| OID symbolic | OID numeric | Type | Access | Description |
| hwXdslCommon | 1.3.6.1.4.1.2011.6.148 | | | This MIB is used for defining Huawei's XDSL common management MIB objects,
which provides XDSL management NMS interfaces. |
| hwXdslCommonMib | 1.3.6.1.4.1.2011.6.148.1 | | | |
| hwXdslAutoDeleteProfUnused | 1.3.6.1.4.1.2011.6.148.1.1 | | | |
| INT hwXdslAutoDeleteProfUnusedProfType | 1.3.6.1.4.1.2011.6.148.1.1.1 | INTEGER | read-write | The profile type of deleting unused XDSL profile.
Options:
1. vdsl2LineConfTemplate(1) - Vdsl line template
2. vdsl2LineConfProf(2) - Vdsl line profile
3. vdsl2ChConfProfile(3) - Vdsl channel profile
4. vdsl2LineAlarmConfTemplate(4) - Vdsl line alarm template
5. vdsl2LineAlarmConfProfile(5) - Vdsl line alarm profile
6. vdsl2ChAlarmConfProfile(6) - Vdsl channel alarm profile
7. vdsl2ServProf(7) - Vdsl service profile (TI mode)
8. vdsl2SpectrumProf(8) - Vdsl spectrum profile (TI mode)
9. vdsl2DpboProf(9) - Vdsl DPBO profile (TI mode)
10. vdsl2UpboProf(10) - Vdsl UPBO profile (TI mode)
11. vdsl2NoiseMarginProf(11) - Vdsl noise-margin profile (TI mode)
12. vdsl2DelayInpProf(12) - Vdsl delay-inp profile (TI mode)
13. vopDataRateConfProf(13) - Xdsl data rate profile (TR165 mode)
14. vopLineSpectrumConfProf(14) - Xdsl line spectrum profile (TR165 mode)
15. vopUPBOConfProf(15) - Xdsl UPBO profile (TR165 mode)
16. vopDPBOConfProf(16) - Xdsl DPBO profile (TR165 mode)
17. vopRFIConfProf(17) - Xdsl RFI profile (TR165 mode)
18. vopSNRMarginConfProf(18) - Xdsl SNR margin profile (TR165 mode)
19. vopINPDelayConfProf(19) - Xdsl INP delay profile (TR165 mode)
20. vopVirtualNoiseConfProf(20) - Xdsl virtual noise profile (TR165 mode)
21. vopModeSpecificPSDConfProf(21) - Xdsl mode specific PSD profile (TR165 mode)
22. adsl2LineConfTemplate(22) - Adsl line template (RFC4706 mode)
23. adsl2LineConfProf(23) - Adsl line profile (RFC4706 mode)
24. adsl2ChConfProfile(24) - Adsl channel profile (RFC4706 mode)
25. adsl2LineAlarmConfTemplate(25) - Adsl line alarm template (RFC4706 mode)
26. adsl2LineAlarmConfProfile(26) - Adsl line alarm profile (RFC4706 mode)
27. adsl2ChAlarmConfProfile(27) - Adsl channel alarm profile (RFC4706 mode)
28. adslLineConfProfile(28) - Adsl line profile (RFC2662 mode)
29. adslLineAlarmConfProfile(29) - Adsl line alarm profile (RFC2662 mode)
30. adslLineExtConfProfile(30) - Adsl line ext profile (RFC2662 mode)
31. shdslLineConfProfile(31) - Shdsl line profile
32. shdslAlarmConfProfile(32) - Shdsl alarm profile
33. vopINMConfProf(33) - Xdsl INM profile (TR165 mode)
34. invalidValue(-1) - Invalid value |
| INT hwXdslAutoDeleteProfUnusedOperType | 1.3.6.1.4.1.2011.6.148.1.1.2 | INTEGER | read-write | The operation type of deleting unused xDSL profile.
Options:
1. first(1) - Delete the first unused xDSL profile
2. all(2) - Delete all the unused xDSL profile
3. invalidValue(-1) - Invalid value |
| hwXdslLineTable | 1.3.6.1.4.1.2011.6.148.1.2 | | not-accessible | The table hwXdslLineTable contains status
parameters of xDSL line. The index of this table is
ifIndex. |
| hwXdslLineEntry | 1.3.6.1.4.1.2011.6.148.1.2.1 | | not-accessible | The table hwXdslLineTable contains status
parameters of xDSL line. The index of this entry is ifIndex. |
| U32 hwAllChActDataRateDs | 1.3.6.1.4.1.2011.6.148.1.2.1.1 | Unsigned32 | read-only | The downstream actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. This is the sum of net date rates
that all bearer channels operating at. |
| U32 hwAllChActDataRateUs | 1.3.6.1.4.1.2011.6.148.1.2.1.2 | Unsigned32 | read-only | The upstream actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. This is the sum of net date rates
that all bearer channels operating at. |
| hwXdslPortFrequentRetrainControlTable | 1.3.6.1.4.1.2011.6.148.1.3 | | not-accessible | The table hwXdslPortFrequentRetrainControlTable contains information
of xDSL port frequent retrain control policy.
The index of this table is ifIndex. |
| hwXdslPortFrequentRetrainControlEntry | 1.3.6.1.4.1.2011.6.148.1.3.1 | | not-accessible | The table hwXdslPortFrequentRetrainControlTable contains information
of xDSL port frequent retrain control policy.
The index of this entry is ifIndex. |
| U32 hwXdslPortFrequentRetrainControlTimes | 1.3.6.1.4.1.2011.6.148.1.3.1.1 | Unsigned32 | read-write | The times that xDSL port frequent retrain.
The invalid value is 4294967295.
If board does not support the operation, the invalid value will be returned. |
| INT hwXdslPortFrequentRetrainControlPolicy | 1.3.6.1.4.1.2011.6.148.1.3.1.2 | INTEGER | read-write | The control policy that xDSL port frequent retrain.
Options:
1. lock(1) - The port is not allowed to go online within 15 minutes
2. nolimit(2) - The port can go online without the limitation of control policies
3. postponed(3) - The port can go online after a postponed time when the number of frequent
resynchronizations on the port reaches the threshold
4. invalidValue(-1) - Invalid value |
| U32 hwXdslPortFrequentRetrainControlPostponedTime | 1.3.6.1.4.1.2011.6.148.1.3.1.3 | Unsigned32 | read-write | The postponed time when control policy of xDSL port frequent retrain is postponed.
The invalid value is 4294967295.
If board does not support the operation, the invalid value will be returned. |
| hwXdslAttndrConfig | 1.3.6.1.4.1.2011.6.148.1.4 | | | |
| INT hwXdslAttndrMethod | 1.3.6.1.4.1.2011.6.148.1.4.1 | INTEGER | read-write | This parameter specifies the method to be used for the calculation of the ATTNDR
in the downstream and upstream direction. The parameter can take three values 0, 1 and 2.
Options:
1. attndrMethod0(0) - The basic Attainable Net Data Rate method
2. attndrMethod1(1) - The improved Attainable Net Data Rate method, If the control
parameter attndr_method is set to a value of 1, the VTU-O and
VTU-R shall use the impulse noise protection limit INP_min0 with
value as indicated in O-TPS. If O-TPS configures for dual bearer
channel mode, then the highest INP_MINn over the bearer channels
shall be used 1
3. attndrMethod2(2) - The improved Attainable Net Data Rate method, If the control parameter
attndr_method is set to a value of 2, the VTU-O and VTU-R shall use an
impulse noise protection limit INP_MIN0 = 0 |
| hwXdslADSL1INPAdaptionConfig | 1.3.6.1.4.1.2011.6.148.1.5 | | | |
| INT hwXdslADSL1INPAdaption | 1.3.6.1.4.1.2011.6.148.1.5.1 | INTEGER | read-write | Enable/Disable the global ADSL1 INP Adaption configuration. This object is defaulted disable(2).
This configuration will take effect after port manually reactivated or board reset.
Options:
1. enable(1) - Enable the ADSL1 INP Adaption configuration
2. disable(2) - Disable the ADSL1 INP Adaption configuration |
| hwXdslTrapsVbOids | 1.3.6.1.4.1.2011.6.148.2 | | | |
| INT hwXdslDynamicCollectResult | 1.3.6.1.4.1.2011.6.148.2.1 | INTEGER | accessible-for-notify | Dynamic information collecting result.
Options:
1. noFail(0) - The dynamic info has been collected successful
2. memFull(1) - The memory used for dynamic info collecting is full
3. otherCause(2) - Other collect failure reason |
| DAT hwXdslDynamicCollectTime | 1.3.6.1.4.1.2011.6.148.2.2 | DateAndTime | accessible-for-notify | Time of the Dynamic information file. |
| I32 hwXdslRequestID | 1.3.6.1.4.1.2011.6.148.2.3 | Integer32 | accessible-for-notify | Request ID. |
| INT hwXdslSeltCompleteResult | 1.3.6.1.4.1.2011.6.148.2.4 | INTEGER | accessible-for-notify | Selt test complete result.
Options:
1. success(1) - Selt test is successful
2. fail(2) - Failed in selt test |
| INT hwAdslProfIDType | 1.3.6.1.4.1.2011.6.148.2.5 | INTEGER | accessible-for-notify | Type of the adsl template ID.
Options:
1. lineTemplate(1) - Indicates line template ID
2. alarmTemplate(2) - Indicates alarm template ID
3. extProfile(3) - Indicates ext profile ID |
| OCT hwXdslProfName | 1.3.6.1.4.1.2011.6.148.2.6 | OCTET STRING | accessible-for-notify | The name of the XDSL profile. |
| U32 hwXdslPortActualUpRate | 1.3.6.1.4.1.2011.6.148.2.7 | Unsigned32 | accessible-for-notify | Xdsl port actual upstream rate. |
| U32 hwXdslPortActualDownRate | 1.3.6.1.4.1.2011.6.148.2.8 | Unsigned32 | accessible-for-notify | Xdsl port actual downstream rate. |
| U32 hwXdslDelProfIndex | 1.3.6.1.4.1.2011.6.148.2.9 | Unsigned32 | accessible-for-notify | Index of the profile which is deleted.
If you delete all the profiles unused, this parameter will be 0xffffffff. |
| OCT hwXdslDelProfName | 1.3.6.1.4.1.2011.6.148.2.10 | OCTET STRING | accessible-for-notify | Name of the profile which is deleted.
If you delete all the profiles unused, this parameter will be a zero string. |
| INT hwXdslSeltTestStartResult | 1.3.6.1.4.1.2011.6.148.2.11 | INTEGER | accessible-for-notify | XDSL selt test start result.
Options:
1. normal(1) - This notification indicates that a SELT task has been started successfully
2. failed(2) - This notification indicates that a SELT task failed to be started |
| hwXdslTraps | 1.3.6.1.4.1.2011.6.148.3 | | | |
| hwXdslCommonTraps | 1.3.6.1.4.1.2011.6.148.3.1 | | | |
| hwXdslCommonTrapsPrefix | 1.3.6.1.4.1.2011.6.148.3.1.0 | | | |
| NTF hwXdslDynamicCollectInfoTrap | 1.3.6.1.4.1.2011.6.148.3.1.0.1 | | | XDSL dynamic collect trap.
This trap message is generated when XDSL dynamic collected. |
| NTF hwXdslSeltCompleteResultTrap | 1.3.6.1.4.1.2011.6.148.3.1.0.2 | | | Selt test complete result trap.
This trap message is generated when selt test completed. |
| NTF hwAdslProfIDChangeTrap | 1.3.6.1.4.1.2011.6.148.3.1.0.3 | | | Adsl profile ID change trap.
This trap message is generated when adsl profile ID changed. |
| NTF hwXdslProfDeleteTrap | 1.3.6.1.4.1.2011.6.148.3.1.0.4 | | | This trap message is generated when Xdsl unused profile trap deleted. |
| NTF hwXdslSeltStartResultTrap | 1.3.6.1.4.1.2011.6.148.3.1.0.5 | | | XDSL selt test start trap.
This notification indicates trap when xDSL selt test start. |
| hwXdslAlarmTraps | 1.3.6.1.4.1.2011.6.148.3.2 | | | |
| hwXdslAlarmTrapsPrefix | 1.3.6.1.4.1.2011.6.148.3.2.0 | | | |
| NTF hwXdslAutoDeactivateLackLicensesAlarmTrap | 1.3.6.1.4.1.2011.6.148.3.2.0.1 | | | This trap message is generated when some xDSL ports or all the xDSL ports
are automatically deactivated due to lack of licenses. |
| NTF hwXdslPortActRateLowerThresholdAlarmTrap | 1.3.6.1.4.1.2011.6.148.3.2.0.2 | | | This trap message is generated when the activation rate
of the xDSL line is lower than the threshold. |