Nortel-Magellan-Passport-Frf5EpMIB

All MIBs › Nortel-Magellan-Passport-Frf5EpMIB

Category: ATM

Description: Manages Nortel Magellan Passport FRF.5 Frame Relay to ATM endpoint interworking configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-Magellan-Passport-Frf5EpMIB?

This Nortel Magellan Passport module manages FRF.5 (Frame Relay Forum Implementation Agreement 5) network interworking configuration on Passport platforms, which defines how Frame Relay traffic is carried over an ATM network via interworking endpoints. It exposes group-level row-status/provisioning tables (mcsMgrFrf5EpGRowStatusTable) and address-level row-status tables (mcsMgrFrf5EpGAddrRowStatusTable) that define FRF.5 endpoint groups and their associated addressing. Its monitoring value is configuration/provisioning verification for the interworking function: confirming FRF.5 endpoint groups and their address entries are correctly provisioned and in an active row status, necessary for Frame Relay-to-ATM interworking traffic to flow correctly between the two network types. This module explicitly implements the Frame Relay Forum's FRF.5 standard for network interworking, making that specification its key dependency, in addition to sharing the common Passport component/row-status conventions. It was deployed on Nortel Magellan Passport switches providing Frame Relay-to-ATM network interworking gateways in carrier multiservice networks. Engineers can download the Nortel-Magellan-Passport-Frf5EpMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-Frf5EpMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Magellan Passport Frame Relay/ATM interworking switch

Monitoring Examples

An operator would poll mcsMgrFrf5EpGRowStatusTable (mcsMgrFrf5EpGRowStatusEntry) to confirm a FRF.5 interworking endpoint group is provisioned and active, then check mcsMgrFrf5EpGAddrRowStatusTable/mcsMgrFrf5EpGAddrRowStatusEntry for the associated address entries to verify addressing is correctly mapped between the Frame Relay and ATM sides. A row stuck in a non-active state in either table would indicate a failed interworking configuration, likely causing traffic between the Frame Relay and ATM segments to fail.

What Can Be Monitored

FRF.5 endpoint group row/provisioning status
endpoint address entry status
interworking group configuration

Imported Objects

From Nortel-Magellan-Passport-McsMgrMIB

mcsMgr	OBJECT-IDENTITY
mcsMgrIndex	OBJECT-TYPE

From Nortel-Magellan-Passport-StandardTextualConventionsMIB

Counter32
DisplayString
Integer32
RowPointer
RowStatus
StorageType
Unsigned32

From Nortel-Magellan-Passport-TextualConventionsMIB

AsciiString
HexString
IntegerSequence
NonReplicated

From Nortel-Magellan-Passport-UsefulDefinitionsMIB

passportMIBs

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
mcsMgrFrf5EpG	1.3.6.1.4.1.562.2.4.1.122.14
mcsMgrFrf5EpGRowStatusTable	1.3.6.1.4.1.562.2.4.1.122.14.1		not-accessible	This entry controls the addition and deletion of mcsMgrFrf5EpG components.
mcsMgrFrf5EpGRowStatusEntry	1.3.6.1.4.1.562.2.4.1.122.14.1.1		not-accessible	A single entry in the table represents a single mcsMgrFrf5EpG component.
ROW mcsMgrFrf5EpGRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mcsMgrFrf5EpG components. These components can be added and deleted.
STR mcsMgrFrf5EpGComponentName	1.3.6.1.4.1.562.2.4.1.122.14.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mcsMgrFrf5EpGStorageType	1.3.6.1.4.1.562.2.4.1.122.14.1.1.4	StorageType	read-only	This variable represents the storage type value for the mcsMgrFrf5EpG tables.
I32 mcsMgrFrf5EpGIndex	1.3.6.1.4.1.562.2.4.1.122.14.1.1.10	Integer32	not-accessible	This variable represents the index for the mcsMgrFrf5EpG tables.
mcsMgrFrf5EpGAddr	1.3.6.1.4.1.562.2.4.1.122.14.2
mcsMgrFrf5EpGAddrRowStatusTable	1.3.6.1.4.1.562.2.4.1.122.14.2.1		not-accessible	This entry controls the addition and deletion of mcsMgrFrf5EpGAddr components.
mcsMgrFrf5EpGAddrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.122.14.2.1.1		not-accessible	A single entry in the table represents a single mcsMgrFrf5EpGAddr component.
ROW mcsMgrFrf5EpGAddrRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGAddr components. These components cannot be added nor deleted.
STR mcsMgrFrf5EpGAddrComponentName	1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mcsMgrFrf5EpGAddrStorageType	1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mcsMgrFrf5EpGAddr tables.
NON mcsMgrFrf5EpGAddrIndex	1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mcsMgrFrf5EpGAddr tables.
mcsMgrFrf5EpGAddrProvTable	1.3.6.1.4.1.562.2.4.1.122.14.2.10		not-accessible	This group contains the provisionable attributes of the Address component.
mcsMgrFrf5EpGAddrProvEntry	1.3.6.1.4.1.562.2.4.1.122.14.2.10.1		not-accessible	An entry in the mcsMgrFrf5EpGAddrProvTable.
STR mcsMgrFrf5EpGAddrRemoteAddress	1.3.6.1.4.1.562.2.4.1.122.14.2.10.1.1	AsciiString	read-write	This attribute specifies the ATM End System Address (AESA) in the ISO NSAP format that is used by each EndPoint under this Frf5EpG to establish a VCC. For example, NSAP ATM address '45000006138292323F000000000020480D002900'.
STR mcsMgrFrf5EpGAddrCommentText	1.3.6.1.4.1.562.2.4.1.122.14.2.10.1.2	AsciiString	read-write	This optional attribute contains additional textual information to be added by the network operator.
mcsMgrFrf5EpGAddrAddrPreTable	1.3.6.1.4.1.562.2.4.1.122.14.2.362		not-accessible	This attribute specifies the list of prefixes directed to the EndPoints under this Frf5EndPointGroup. The individual end point is selected for each subconnection on the basis of its supportedTransferPriorities. For example, E.164 prefix 'e.613722', X.121 prefix 'x.302'.
mcsMgrFrf5EpGAddrAddrPreEntry	1.3.6.1.4.1.562.2.4.1.122.14.2.362.1		not-accessible	An entry in the mcsMgrFrf5EpGAddrAddrPreTable.
STR mcsMgrFrf5EpGAddrAddrPreValue	1.3.6.1.4.1.562.2.4.1.122.14.2.362.1.1	AsciiString	read-write	This variable represents both the value and the index for the mcsMgrFrf5EpGAddrAddrPreTable.
ROW mcsMgrFrf5EpGAddrAddrPreRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.2.362.1.2	RowStatus	write-only	This variable is used to control the addition and deletion of individual values of the mcsMgrFrf5EpGAddrAddrPreTable.
mcsMgrFrf5EpGEp	1.3.6.1.4.1.562.2.4.1.122.14.3
mcsMgrFrf5EpGEpRowStatusTable	1.3.6.1.4.1.562.2.4.1.122.14.3.1		not-accessible	This entry controls the addition and deletion of mcsMgrFrf5EpGEp components.
mcsMgrFrf5EpGEpRowStatusEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.1.1		not-accessible	A single entry in the table represents a single mcsMgrFrf5EpGEp component.
ROW mcsMgrFrf5EpGEpRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEp components. These components can be added and deleted.
STR mcsMgrFrf5EpGEpComponentName	1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mcsMgrFrf5EpGEpStorageType	1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mcsMgrFrf5EpGEp tables.
I32 mcsMgrFrf5EpGEpIndex	1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.10	Integer32	not-accessible	This variable represents the index for the mcsMgrFrf5EpGEp tables.
mcsMgrFrf5EpGEpLmi	1.3.6.1.4.1.562.2.4.1.122.14.3.2
mcsMgrFrf5EpGEpLmiRowStatusTable	1.3.6.1.4.1.562.2.4.1.122.14.3.2.1		not-accessible	This entry controls the addition and deletion of mcsMgrFrf5EpGEpLmi components.
mcsMgrFrf5EpGEpLmiRowStatusEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1		not-accessible	A single entry in the table represents a single mcsMgrFrf5EpGEpLmi component.
ROW mcsMgrFrf5EpGEpLmiRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpLmi components. These components can be added and deleted.
STR mcsMgrFrf5EpGEpLmiComponentName	1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mcsMgrFrf5EpGEpLmiStorageType	1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mcsMgrFrf5EpGEpLmi tables.
NON mcsMgrFrf5EpGEpLmiIndex	1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mcsMgrFrf5EpGEpLmi tables.
mcsMgrFrf5EpGEpLmiParmsTable	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10		not-accessible	This group contains the provisionable attributes of the Local Management Interface component.
mcsMgrFrf5EpGEpLmiParmsEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1		not-accessible	An entry in the mcsMgrFrf5EpGEpLmiParmsTable.
INT mcsMgrFrf5EpGEpLmiProcedures	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.1	INTEGER	read-write	This attribute selects the procedures to be used for the Local Management Interface. The following are the supported procedures: none: no Local Management Interface procedures are running on the ATM VCC. This accomodates remote interworking functions which do not implement LMI procedures. In this case, the remaining attributes of this group will be ignored. ccitt: Local Management Interface procedures from the CCITT specification are supported. Dlci/0 is used for the LMI protocol, to comply with FRF.5. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol.
INT mcsMgrFrf5EpGEpLmiAsyncStatusReport	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.2	INTEGER	read-write	This attribute selects the use of asynchronous PVC status report procedures as specified in the CCITT specification (ITU-T Q.933, Annex A), and the ANSI specification Annex D.
U32 mcsMgrFrf5EpGEpLmiErrorEventThreshold	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.3	Unsigned32	read-write	For the network side procedure, an event is defined as follows: (1) receipt of a STATUS ENQUIRY message, or (2) expiration of timer T392. An error event is (1) nonreceipt of STATUS ENQUIRY in T392 seconds; (2) invalid format of an LMI message; (3) invalid receive sequence number. For the user side procedure, an event is defined as a polling cycle or a status enquiry and status report exchange. An error event is (1) non-receipt of a STATUS within the polling cycle, or (2) invalid format of an LMI message, or (3) invalid sequence number. This attribute specifies the number of error events which, if they occur within eventCount events, will cause a protocol error condition. The condition is cleared after eventCount sequential correct events occur. It must be less than or equal to eventCount (n393).
U32 mcsMgrFrf5EpGEpLmiEventCount	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.4	Unsigned32	read-write	This attribute specifies the number of contiguous events within which no more than eventErrorThreshold error events are allowed. It must be greater than or equal to errorEventThreshold (n392).
U32 mcsMgrFrf5EpGEpLmiCheckPointTimer	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.5	Unsigned32	read-write	This attribute selects the time (in seconds) within which a STATUS ENQUIRY message is expected. It must be greater than linkVerificationTimer (t391).
INT mcsMgrFrf5EpGEpLmiSide	1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.8	INTEGER	read-write	This attribute selects the user side procedure (DTE), or the network side procedure (DCE), or both the user side and the network side procedures of the LMI. This attribute can be set to user, network or both.
mcsMgrFrf5EpGEpLmiNniParmsTable	1.3.6.1.4.1.562.2.4.1.122.14.3.2.11		not-accessible	This group contains the provisionable attributes of the FRF.5 LMI procedures which are unique to NNI.
mcsMgrFrf5EpGEpLmiNniParmsEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.2.11.1		not-accessible	An entry in the mcsMgrFrf5EpGEpLmiNniParmsTable.
U32 mcsMgrFrf5EpGEpLmiFullStatusPollingCycles	1.3.6.1.4.1.562.2.4.1.122.14.3.2.11.1.1	Unsigned32	read-write	This attribute specifies how frequently the FRF.5 LMI initiates a Status Enquiry for a full PVC status report. A polling cycle is a Status Enquiry and Status Report exchange.
U32 mcsMgrFrf5EpGEpLmiLinkVerificationTimer	1.3.6.1.4.1.562.2.4.1.122.14.3.2.11.1.2	Unsigned32	read-write	This attribute specifies how frequently the FRF.5 LMI initiates a Status Enquiry for link integrity verification. It must be less than checkPointTimer (t392).
mcsMgrFrf5EpGEpLmiStateTable	1.3.6.1.4.1.562.2.4.1.122.14.3.2.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mcsMgrFrf5EpGEpLmiStateEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1		not-accessible	An entry in the mcsMgrFrf5EpGEpLmiStateTable.
INT mcsMgrFrf5EpGEpLmiAdminState	1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mcsMgrFrf5EpGEpLmiOperationalState	1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mcsMgrFrf5EpGEpLmiUsageState	1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mcsMgrFrf5EpGEpLmiPsiTable	1.3.6.1.4.1.562.2.4.1.122.14.3.2.13		not-accessible	This group provides the protocol status of the Local Management Interface.
mcsMgrFrf5EpGEpLmiPsiEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.2.13.1		not-accessible	An entry in the mcsMgrFrf5EpGEpLmiPsiTable.
INT mcsMgrFrf5EpGEpLmiProtocolStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.2.13.1.1	INTEGER	read-only	This attribute indicates whether the LMI is in an error condition or whether the protocol is behaving normally. This attribute will be set to errorCondition after enough LMI errors have been detected to warrant a change in condition. This occurs when n392 of the last n393 events are in error. The error condition is lifted when a sufficient number of consecutive events has occurred without error. This occurs when n393 consecutive good events take place. The consequence of an error condition is that all DLCIs on this interface will become inactive in both directions.
mcsMgrFrf5EpGEpLmiStatsTable	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14		not-accessible	This group contains the operational statistics for the FRF.5 NNI Local Management Interface.
mcsMgrFrf5EpGEpLmiStatsEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1		not-accessible	An entry in the mcsMgrFrf5EpGEpLmiStatsTable.
C32 mcsMgrFrf5EpGEpLmiKeepAliveStatusToInterface	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.1	Counter32	read-only	This attribute counts the Local Management Interface keep alive status messages sent to the ATM VCC in response to a status enquiry for keep alive status. When the maximum count is reached it wraps to zero.
C32 mcsMgrFrf5EpGEpLmiFullStatusToInterface	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.2	Counter32	read-only	This attribute counts the Local Management Interface full status messages sent to the ATM VCC in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
C32 mcsMgrFrf5EpGEpLmiKeepAliveStatusEnqFromInterface	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.3	Counter32	read-only	This attribute counts the Local Management Interface valid keep alive status enquiry messages received from the ATM VCC. When the maximum count is reached it wraps to zero.
C32 mcsMgrFrf5EpGEpLmiFullStatusEnqFromInterface	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.4	Counter32	read-only	This attribute counts the Local Management Interface valid full status enquiry messages received from the ATM VCC. When the maximum count is reached it wraps to zero.
STR mcsMgrFrf5EpGEpLmiNetworkSideEventHistory	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.5	AsciiString	read-only	This attribute displays the Local Management Interface network side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status enquiry message. An error event is either a T392 timer expiry or receipt of a status enquiry with an incorrect sequence number.
STR mcsMgrFrf5EpGEpLmiUserSideEventHistory	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.6	AsciiString	read-only	This attribute displays the Local Management Interface user side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status message. An error event is either a T391 timer expiry or receipt of a status message with an incorrect sequence number.
C32 mcsMgrFrf5EpGEpLmiProtocolErrors	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.7	Counter32	read-only	This attribute counts the number of Local Management Interface protocol errors. It is the sum of the sequence (sequenceErrors and statusSequenceErrors) and timeout (pollingVerifTimeouts and noStatusReportCount) errors. When the maximum count is reached it wraps to zero.
C32 mcsMgrFrf5EpGEpLmiUnexpectedIes	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.8	Counter32	read-only	This attribute counts the number of Local Managament Interface frames received with an Information Element identifier that is unknown or unexpected. An unexpected Information Element is not a protocol error. When the maximum count is reached, this counter wraps to zero.
C32 mcsMgrFrf5EpGEpLmiSequenceErrors	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.9	Counter32	read-only	This attribute counts the number of Local Management Interface Status Enquiry message sequence errors. A sequence error is receipt of a Status Enquiry message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
C32 mcsMgrFrf5EpGEpLmiStatusSequenceErrors	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.10	Counter32	read-only	This attribute counts the number of Local Management Interface Status message sequence errors. A sequence error is receipt of a Status message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
C32 mcsMgrFrf5EpGEpLmiUnexpectedReports	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.11	Counter32	read-only	This attribute counts the number of Local Management Interface frames received with an unknown or unexpected report type. An unexpected report type is not a protocol error. When the maximum count is reached the counter wraps to zero.
C32 mcsMgrFrf5EpGEpLmiPollingVerifTimeouts	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.12	Counter32	read-only	This attribute counts the checkPointTimer (T392) expiries occurring on the Local Management Interface. When the maximum count is reached the counter wraps to zero.
C32 mcsMgrFrf5EpGEpLmiNoStatusReportCount	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.13	Counter32	read-only	This attribute counts the number of times when no status report or an invalid status report comes from the external network. This attribute is incremented: i) after a status enquiry is sent out and the T391 timer expires without having a status report received. ii) if an invalid status report is received. When the maximum count is reached it wraps to zero.
C32 mcsMgrFrf5EpGEpLmiKeepAliveEnqToIf	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.14	Counter32	read-only	This attribute counts the number of Local Management Interface keep alive enquiry status messages sent to the external user device for keep alive status. When the maximum count is reached it wraps to zero.
C32 mcsMgrFrf5EpGEpLmiFullStatusEnqToIf	1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.15	Counter32	read-only	This attribute counts the number of Local Management Interface full status messages sent to the external user device in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
mcsMgrFrf5EpGEpEpd	1.3.6.1.4.1.562.2.4.1.122.14.3.3
mcsMgrFrf5EpGEpEpdRowStatusTable	1.3.6.1.4.1.562.2.4.1.122.14.3.3.1		not-accessible	This entry controls the addition and deletion of mcsMgrFrf5EpGEpEpd components.
mcsMgrFrf5EpGEpEpdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1		not-accessible	A single entry in the table represents a single mcsMgrFrf5EpGEpEpd component.
ROW mcsMgrFrf5EpGEpEpdRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpEpd components. These components cannot be added nor deleted.
STR mcsMgrFrf5EpGEpEpdComponentName	1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mcsMgrFrf5EpGEpEpdStorageType	1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mcsMgrFrf5EpGEpEpd tables.
NON mcsMgrFrf5EpGEpEpdIndex	1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mcsMgrFrf5EpGEpEpd tables.
mcsMgrFrf5EpGEpEpdProvTable	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10		not-accessible	This group contains the provisionable attributes of the FRF.5 End Point.
mcsMgrFrf5EpGEpEpdProvEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1		not-accessible	An entry in the mcsMgrFrf5EpGEpEpdProvTable.
NUM mcsMgrFrf5EpGEpEpdRemoteConnectionIdentifier	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.3	IntegerSequence	read-write	This attribute specifies the remote connection identifier. It either represents the VPI.VCI logical channel number assignment of a remote ATM interface, or the Endpoint.Frf5EndPointGroup instances of a remote Passport FRF.5 EndPoint.
U32 mcsMgrFrf5EpGEpEpdConnectionTransferPriority	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.4	Unsigned32	read-write	This attribute specifies the transfer priority used to establish the ATM connection. The EndPoint references the ModuleData FrameRelayService AtmNetworking TransferPriority/n component to determine the ATM service category to be used by the connection. This attribute is also used to determine which EndPoint within an Frf5EndPointGroup is to multiplex a particular FrAtm Dlci. DESCRIPTION
U32 mcsMgrFrf5EpGEpEpdCommittedInformationRate	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.5	Unsigned32	read-write	This attribute specifies the committed information rate (CIR), and represents the rate at which the network FRF.5 ATM VCC agrees to transfer information under normal conditions. A conservative CIR value would be the sum of the CIRs of all the individual FrAtm Dlcis multiplexed by the VCC. The cir is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
U32 mcsMgrFrf5EpGEpEpdExcessInformationRate	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.6	Unsigned32	read-write	This attribute specifies the excess information rate (EIR), and represents the rate at which the network FRF.5 ATM VCC attempts to transfer information. A conservative EIR value would be the sum of the EIRs of all the individual FrAtm Dlcis multiplexed by the VCC. The eir is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
U32 mcsMgrFrf5EpGEpEpdCommittedBurstSize	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.7	Unsigned32	read-write	This attribute specifies the committed burst size (Bc), and represents the amount of data that the network FRF.5 ATM VCC agrees to transfer under normal conditions. A conservative Bc value would be the sum of the Bcs of all the individual FrAtm Dlcis multiplexed by the VCC. The bc is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
INT mcsMgrFrf5EpGEpEpdType	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.8	INTEGER	read-write	This attribute specifies the FRF.5 End Point type. If the value is provisioned as master, this End Point is responsible for initiating the SPVC call to set up the FRF.5 ATM VCC. If the value is provisioned as slave, this End Point receives call setup requests from a master remote end.
U32 mcsMgrFrf5EpGEpEpdAccessRate	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.9	Unsigned32	read-write	This attribute represents the access rate of the FRF.5 EndPoint. A conservative value would be the sum of the access rates of all the FrAtms' that have DLCIs multiplexed by the VCC. The access rate is converted into ATM service parameters when conversion policies 3, 4 and 5 are used. For policy 6, this attribute is ignored.
U32 mcsMgrFrf5EpGEpEpdExcessBurstSize	1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.10	Unsigned32	read-write	This attribute specifies the excess burst size (Be), and represents the amount of uncommitted data that the network FRF.5 ATM VCC agrees to transfer under normal conditions. A conservative Be value would be the sum of the Bes of all the individual FrAtm Dlcis multiplexed by the VCC. The be is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
mcsMgrFrf5EpGEpEpdCidDataTable	1.3.6.1.4.1.562.2.4.1.122.14.3.3.11		not-accessible	This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
mcsMgrFrf5EpGEpEpdCidDataEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.3.11.1		not-accessible	An entry in the mcsMgrFrf5EpGEpEpdCidDataTable.
U32 mcsMgrFrf5EpGEpEpdCustomerIdentifier	1.3.6.1.4.1.562.2.4.1.122.14.3.3.11.1.1	Unsigned32	read-write	This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
mcsMgrFrf5EpGEpDlci	1.3.6.1.4.1.562.2.4.1.122.14.3.4
mcsMgrFrf5EpGEpDlciRowStatusTable	1.3.6.1.4.1.562.2.4.1.122.14.3.4.1		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This entry controls the addition and deletion of mcsMgrFrf5EpGEpDlci components.
mcsMgrFrf5EpGEpDlciRowStatusEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1		not-accessible	A single entry in the table represents a single mcsMgrFrf5EpGEpDlci component.
ROW mcsMgrFrf5EpGEpDlciRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpDlci components. These components cannot be added nor deleted.
STR mcsMgrFrf5EpGEpDlciComponentName	1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mcsMgrFrf5EpGEpDlciStorageType	1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the mcsMgrFrf5EpGEpDlci tables.
I32 mcsMgrFrf5EpGEpDlciIndex	1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.10	Integer32	not-accessible	This variable represents the index for the mcsMgrFrf5EpGEpDlci tables.
mcsMgrFrf5EpGEpDlciOperTable	1.3.6.1.4.1.562.2.4.1.122.14.3.4.10		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This group contains the operational attributes for the FRF.5 DLCI.
mcsMgrFrf5EpGEpDlciOperEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1		not-accessible	An entry in the mcsMgrFrf5EpGEpDlciOperTable.
INT mcsMgrFrf5EpGEpDlciABitStatusToIf	1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.1	INTEGER	read-only	This attribute indicates the most recent A-bit status sent to the ATM VCC. If the value is inactive, the reason for the LMI failure is given by the aBitReasonToNetwork.
INT mcsMgrFrf5EpGEpDlciABitReasonToIf	1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.2	INTEGER	read-only	This attribute indicates the reason for the latest inactive A-bit status sent to the ATM VCC. The value is notApplicable when the aBitStatusToNetwork is active. The value is remoteUserSignaled if the FrAtm originating the A-Bit status has detected that the virtual circuit is down at the remote network through the LMI protocol. The FrAtm must be running network site LMI protocol for this A-Bit status reason to be sent. The value is localLmiError if the LMI protocol is down at this Ep. The value is remoteLmiError if the LMI protocol is down at the FrAtm originating this A-Bit status reason. The value is localLinkDown if the physical interface is disabled at this Ep. The value is pvcDown if no A-Bit status has been sent to this Ep (i.e., no A-Bit status has been relayed from the FrAtm). The value is remoteLinkDown if the physical interface is disabled at the FrAtm originating this A-Bit status reason.
INT mcsMgrFrf5EpGEpDlciABitStatusFromIf	1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.3	INTEGER	read-only	This attribute indicates the most recent A-bit status received from the ATM VCC. If the value is inactive, the reason for the LMI failure is given by the aBitReasonFromNetwork.
INT mcsMgrFrf5EpGEpDlciABitReasonFromIf	1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.4	INTEGER	read-only	This attributes indicates the reason for the latest inactive A-bit status received from the ATM VCC. The value is notApplicable when the aBitStatusFromNetwork is active. The value is remoteUserSignaled if the remote FRF.5 End Point originating the A-Bit status has detected that the virtual circuit is down at the remote network through the LMI protocol. The remote FRF.5 End Point must be running network site LMI protocol for this A-Bit status reason to be sent. The value is localLmiError if the LMI protocol is down at this Ep. The value is localLinkDown if the physical interface is disabled at this Ep. The value is missingFromLmiReport if the remote FRF.5 End Point did not provide a reason along with the inactive A-Bit status.
STR mcsMgrFrf5EpGEpDlciAccessConnectionComponent	1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.5	AsciiString	read-only	This attribute identifies the FrAtm Dlci to which this Dlci component is bound.
mcsMgrFrf5EpGEpAtmCon	1.3.6.1.4.1.562.2.4.1.122.14.3.5
mcsMgrFrf5EpGEpAtmConRowStatusTable	1.3.6.1.4.1.562.2.4.1.122.14.3.5.1		not-accessible	This entry controls the addition and deletion of mcsMgrFrf5EpGEpAtmCon components.
mcsMgrFrf5EpGEpAtmConRowStatusEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1		not-accessible	A single entry in the table represents a single mcsMgrFrf5EpGEpAtmCon component.
ROW mcsMgrFrf5EpGEpAtmConRowStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpAtmCon components. These components cannot be added nor deleted.
STR mcsMgrFrf5EpGEpAtmConComponentName	1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mcsMgrFrf5EpGEpAtmConStorageType	1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.4	StorageType	read-only	This variable represents the storage type value for the mcsMgrFrf5EpGEpAtmCon tables.
NON mcsMgrFrf5EpGEpAtmConIndex	1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mcsMgrFrf5EpGEpAtmCon tables.
mcsMgrFrf5EpGEpAtmConOperTable	1.3.6.1.4.1.562.2.4.1.122.14.3.5.10		not-accessible	This attribute group contains the operational attributes for the NapAtmConnection component.
mcsMgrFrf5EpGEpAtmConOperEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.5.10.1		not-accessible	An entry in the mcsMgrFrf5EpGEpAtmConOperTable.
NUM mcsMgrFrf5EpGEpAtmConNextHop	1.3.6.1.4.1.562.2.4.1.122.14.3.5.10.1.1	RowPointer	read-only	This attribute shows the component name of the AtmIf Vcc Ep or AtmCon component to which this switched connection is established.
mcsMgrFrf5EpGEpStateTable	1.3.6.1.4.1.562.2.4.1.122.14.3.10		not-accessible	This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
mcsMgrFrf5EpGEpStateEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1		not-accessible	An entry in the mcsMgrFrf5EpGEpStateTable.
INT mcsMgrFrf5EpGEpAdminState	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
INT mcsMgrFrf5EpGEpOperationalState	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
INT mcsMgrFrf5EpGEpUsageState	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OCT mcsMgrFrf5EpGEpAvailabilityStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.4	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OCT mcsMgrFrf5EpGEpProceduralStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.5	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OCT mcsMgrFrf5EpGEpControlStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.6	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OCT mcsMgrFrf5EpGEpAlarmStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.7	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
INT mcsMgrFrf5EpGEpStandbyStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.8	INTEGER	read-only	If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
INT mcsMgrFrf5EpGEpUnknownStatus	1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.9	INTEGER	read-only	This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
mcsMgrFrf5EpGEpOperTable	1.3.6.1.4.1.562.2.4.1.122.14.3.11		not-accessible	This group contains the operational attributes for the FRF.5 ATM connection.
mcsMgrFrf5EpGEpOperEntry	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1		not-accessible	An entry in the mcsMgrFrf5EpGEpOperTable.
U32 mcsMgrFrf5EpGEpLastVccClearCause	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.4	Unsigned32	read-only	This attribute indicates the clear cause value of the last SPVC release message received on the FRF.5 end point Vcc pipe.
U32 mcsMgrFrf5EpGEpConnectionTransferPriority	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.5	Unsigned32	read-only	This attribute indicates the transfer priority used to establish the ATM connection and to multiplex the Frame Relay DLCIs.
INT mcsMgrFrf5EpGEpServiceCategory	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.6	INTEGER	read-only	This attribute indicates the ATM service category that is used for this connection.
U32 mcsMgrFrf5EpGEpPeakCellRate01	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.8	Unsigned32	read-only	This attribute indicates the Peak Cell Rate (PCR) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The pcr01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
U32 mcsMgrFrf5EpGEpSustainedCellRate0	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.9	Unsigned32	read-only	This attribute indicates the Sustained Cell Rate (SCR) of the FRF.5 ATM VCC for high priority cells (with CLP=0). The scr0 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
U32 mcsMgrFrf5EpGEpSustainedCellRate01	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.10	Unsigned32	read-only	This attribute indicates the Sustained Cell Rate (SCR) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The scr01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
U32 mcsMgrFrf5EpGEpMaximumBurstSize0	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.11	Unsigned32	read-only	This attribute indicates the Maximum Burst Size (MBS) of the FRF.5 ATM VCC for high priority cells (with CLP=0). The mbs0 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
U32 mcsMgrFrf5EpGEpMaximumBurstSize01	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.12	Unsigned32	read-only	This attribute indicates the Maximum Burst Size (MBS) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The mbs01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
U32 mcsMgrFrf5EpGEpAvgFrameSize	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.13	Unsigned32	read-only	This attribute indicates the average frame size that is used in the traffic parameter conversion policy calculations for this end point.
INT mcsMgrFrf5EpGEpTrafficParmConversionPolicy	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.14	INTEGER	read-only	This attribute indicates the traffic parameter conversion policy used to specify the equivalent ATM bandwidth rate at this end point. Policy 3 characterizes the traffic in the following way: - ATM traffic descriptor type 6 is selected - PCR0+1 is based on the AR - SCR0+1 is based on the CIR and EIR - MBS0+1 is based on Bc,Be,CIR,EIR and AR - Takes into account that the instananeous rate of the frame relay stream can burst above CIR and up tp the AR. Policy 4 characterizes the traffic in the following way: - ATM traffic descriptor type 7 or 8 is selected. Type 7 is chosen when non-conforming cells are to be discarded and type 8 when non-conforming cells are tagged by UPC traffic policer. - PCR0+1 is based on the AR - SCR0 is based on the CIR - MBS0 is based on Bc,CIR and AR - There is no direct characterization of EIR. The allowed EIR can be derived using the difference between the AR and CIR. Policy 5 characterizes the traffic in the following way: - ATM traffic descriptor type 7 or 8 is selected . Type 7 is chosen when non-conforming cells are to be discarded and type 8 when non-conforming cells are tagged by UPC traffic policer - PCR0+1 is based on CIR and EIR - SCR0 is based on the CIR - MBS0 is based on the Bc,CIR and AR - The maximum PCR is no longer based on AR but based on the CIR and EIR. Policy 6 characterizes the traffic in the following way: - ATM traffic descriptor type 3 is selected - PCR0+1 is based only on CIR.
INT mcsMgrFrf5EpGEpType	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.15	INTEGER	read-only	This attribute indicates the FRF.5 End Point type. If the value is master, this End Point is responsible for initiating the call to set up the FRF.5 ATM VCC. If the value is slave, this End Point receives call setup requests from the remote end.
STR mcsMgrFrf5EpGEpLastVccCauseDiag	1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.20	HexString	read-only	This attribute indicates the diagnostic value of the last SPVC release message received on the FRF.5 end point Vcc pipe.
frf5EpMIB	1.3.6.1.4.1.562.2.4.2.121
frf5EpGroup	1.3.6.1.4.1.562.2.4.2.121.1
frf5EpGroupBD	1.3.6.1.4.1.562.2.4.2.121.1.4
frf5EpGroupBD02	1.3.6.1.4.1.562.2.4.2.121.1.4.3
frf5EpGroupBD02A	1.3.6.1.4.1.562.2.4.2.121.1.4.3.2
frf5EpCapabilities	1.3.6.1.4.1.562.2.4.2.121.3
frf5EpCapabilitiesBD	1.3.6.1.4.1.562.2.4.2.121.3.4
frf5EpCapabilitiesBD02	1.3.6.1.4.1.562.2.4.2.121.3.4.3
frf5EpCapabilitiesBD02A	1.3.6.1.4.1.562.2.4.2.121.3.4.3.2

RFC description

Nortel FRF.5 frame relay endpoint management with NSAP address and prefix configuration.

Start monitoring Nortel Magellan Passport Frame Relay/ATM interworking switch (FRF.5) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-Magellan-Passport-Frf5EpMIB

What Is Nortel-Magellan-Passport-Frf5EpMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description