All MIBs › MOXA-NP6000-MIB
Organization: Moxa Technologies Co.
Last Updated: 2006-07-12
Category: Console Servers
Description: Manages Moxa NPort 6000 series serial server port configuration and sessions.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MOXA-NP6000-MIB?
MOXA-NP6000-MIB is a vendor-specific module for Moxa's NPort 6000 series secure serial device servers, which convert RS-232/422/485 serial devices to network-accessible, SSH/SSL-secured connections. The visible structure exposes a management subtree (swMgmt) covering device and serial-port configuration. Monitoring emphasis is on serial port and session health: whether serial ports are up and correctly configured, and how many secure sessions are active, alongside device software/firmware status. It follows Moxa's common device-server management conventions shared across the NPort product line. Typical deployment is industrial serial-to-Ethernet gateway environments (SCADA, PLCs) using Moxa NPort 6000 secure device servers. Engineers can download the MOXA-NP6000-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in MOXA-NP6000-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Moxa NPort 6000 series serial device server
Monitoring Examples
An admin polls objects under the swMgmt subtree to check serial port status and active session/connection information on the NPort 6000, watching for a hung serial link or an unexpected drop in active sessions. Because only the top-level swMgmt node is visible in this excerpt, specific leaf object or table names for individual ports and sessions aren't confirmed here.
What Can Be Monitored
- serial port operational status
- session/connection state
- device configuration
- firmware/software status
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-SMI
| IpAddress | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| MacAddress | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| moxa | 1.3.6.1.4.1.8691 | |||
| nport | 1.3.6.1.4.1.8691.2 | |||
| np6000 | 1.3.6.1.4.1.8691.2.8 | The MIB module for Moxa NPort 6000 series specific information. | ||
| swMgmt | 1.3.6.1.4.1.8691.2.8.1 | |||
| overview | 1.3.6.1.4.1.8691.2.8.1.1 | |||
| STR modelName | 1.3.6.1.4.1.8691.2.8.1.1.1 | DisplayString | read-only | The model name of the NPort. The possible values of this parameter are: 'NP6150' for NPort 6150, 'NP6250' for NPort 6250, 'NP6250-S-SC' for NPort 6250-S-SC, 'NP6250-M-SC' for NPort NPort 6250-M-SC, 'NP6450' for NPort 6450, 'NP6650-8' for NPort 6650-8, and 'NP6650-16' for NPort 6650-16. |
| INT serialNumber | 1.3.6.1.4.1.8691.2.8.1.1.2 | INTEGER | read-only | The serial number of the NPort. Every NPort 6000 series device server is assigned a unique serial number before it is shipped. |
| STR firmwareVersion | 1.3.6.1.4.1.8691.2.8.1.1.3 | DisplayString | read-only | The version of the firmware currently running on the NPort. |
| MAC macAddress | 1.3.6.1.4.1.8691.2.8.1.1.4 | MacAddress | read-only | The MAC address of the NPort's Ethernet interface. |
| STR viewLanSpeed | 1.3.6.1.4.1.8691.2.8.1.1.5 | DisplayString | read-only | The current speed and link status of the NPort's built-in LAN port. The possible values are 'No link', '10M/Link,' or '100M/Link.' |
| STR viewLanModuleSpeed | 1.3.6.1.4.1.8691.2.8.1.1.6 | DisplayString | read-only | The current speed and link status of the the network module's LAN ports, if the module is installed. The value includes two parts. Each part indicates the status of one of the LAN ports. The possible values are 'No link', '10M/Link,' '100M/Link,' or continunous dashes to indicate that the LAN module is not installed. |
| STR upTime | 1.3.6.1.4.1.8691.2.8.1.1.7 | DisplayString | read-only | The time (in human-readable notation) since the system was was last re-initialized. |
| STR moduleType | 1.3.6.1.4.1.8691.2.8.1.1.8 | DisplayString | read-only | The module name currently plugged into the NPort. |
| basicSetting | 1.3.6.1.4.1.8691.2.8.1.2 | |||
| serverSetting | 1.3.6.1.4.1.8691.2.8.1.2.1 | |||
| STR serverName | 1.3.6.1.4.1.8691.2.8.1.2.1.1 | DisplayString | read-write | A text string used to identify the NPort. |
| STR serverLocation | 1.3.6.1.4.1.8691.2.8.1.2.1.2 | DisplayString | read-write | A text string used to identify the location of the NPort. This option is useful for specifying the location or application of different NPort device servers. |
| timeSetting | 1.3.6.1.4.1.8691.2.8.1.2.2 | |||
| INT timeZone | 1.3.6.1.4.1.8691.2.8.1.2.2.1 | INTEGER | read-write | The time-zone index of the NPort. |
| DAT localTime | 1.3.6.1.4.1.8691.2.8.1.2.2.2 | DateAndTime | read-write | The system time in seconds since 1970/1/1. |
| STR timeServer | 1.3.6.1.4.1.8691.2.8.1.2.2.3 | DisplayString | read-write | The NPort 6000 series device server uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the NPort 6000 series device server is configured with the correct Time server address, it will request time information from the Time server every 10 minutes. |
| networkSetting | 1.3.6.1.4.1.8691.2.8.1.3 | |||
| INT ipConfiguration | 1.3.6.1.4.1.8691.2.8.1.3.1 | INTEGER | read-write | The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP, and PPPoE. |
| IP sysIpAddress | 1.3.6.1.4.1.8691.2.8.1.3.2 | IpAddress | read-write | An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment. |
| IP netMask | 1.3.6.1.4.1.8691.2.8.1.3.3 | IpAddress | read-write | A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort 6000 series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort 6000 series device server, a connection is established directly from the NPort 6000 series device server. Otherwise, the connection is established through the given default gateway. |
| IP defaultGateway | 1.3.6.1.4.1.8691.2.8.1.3.4 | IpAddress | read-only | A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort 6000 series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator. |
| IP dnsServer1IpAddr | 1.3.6.1.4.1.8691.2.8.1.3.5 | IpAddress | read-write | The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the websites correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection. |
| IP dnsServer2IpAddr | 1.3.6.1.4.1.8691.2.8.1.3.6 | IpAddress | read-write | The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the websites correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection. |
| STR pppoeUserAccount | 1.3.6.1.4.1.8691.2.8.1.3.7 | DisplayString | read-write | The user account used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username and password that they received from their ISP to establish a network connection. |
| STR pppoePassword | 1.3.6.1.4.1.8691.2.8.1.3.8 | DisplayString | read-write | The password used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username and password that they received from their ISP to establish a network connection. |
| INT winsFunction | 1.3.6.1.4.1.8691.2.8.1.3.9 | INTEGER | read-write | Enable or disable the WINS server. |
| IP winsServer | 1.3.6.1.4.1.8691.2.8.1.3.10 | IpAddress | read-write | If a WINS Server is connected to the network, use this field to record the WINS Servers IP address. TCP/IP uses IP addresses to identify hosts, but users often use symbolic names, such as computer names. The WINS Server, which uses NetBIOS over TCP/IP, contains a dynamic database to map computer names to IP addresses. |
| INT lan1Speed | 1.3.6.1.4.1.8691.2.8.1.3.11 | INTEGER | read-write | IEEE802.3 Ethernet supports the auto negotiation speed function to get suitable speeds. However, for connecting to some switches/hubs, the communication speed must be fixed at 100 Mbps or 10 Mbps. Users can use this function to fix the communication speed. |
| INT routingProtocol | 1.3.6.1.4.1.8691.2.8.1.3.12 | INTEGER | read-write | The routing protocol used by the NPort. This value could be none, RIP-1, or RIP-2. |
| INT gratuitousArp | 1.3.6.1.4.1.8691.2.8.1.3.13 | INTEGER | read-write | Enable or disable the gratuitous ARP function. For some applications, users need the NPort 6000 series device server to send broadcast packets to update the ARP table on the server. If the customer enables this function and sets the send period, the NPort 6000 series device server will send broadcast packets periodically. |
| INT gratuitousArpSendPeriod | 1.3.6.1.4.1.8691.2.8.1.3.14 | INTEGER | read-write | The send period of the gratuitous ARP function. |
| portSetting | 1.3.6.1.4.1.8691.2.8.1.4 | |||
| opModeSetting | 1.3.6.1.4.1.8691.2.8.1.4.1 | |||
| opMode | 1.3.6.1.4.1.8691.2.8.1.4.1.1 | |||
| opModePortTable | 1.3.6.1.4.1.8691.2.8.1.4.1.1.1 | not-accessible | The serial ports' operation mode table. | |
| opModePortEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1 | not-accessible | The serial port's operation mode entry. | |
| INT portIndex | 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.1 | INTEGER | read-only | The serial port index. |
| INT portApplication | 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.2 | INTEGER | read-write | The application of the serial port. Note that changing this setting may also change the operation mode. |
| INT portMode | 1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.3 | INTEGER | read-write | The operation mode of the serial port. Note that changing this setting may also change the application. |
| application | 1.3.6.1.4.1.8691.2.8.1.4.1.2 | |||
| deviceControl | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1 | |||
| deviceControlTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1 | not-accessible | The Device Control application table. | |
| deviceControlEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1 | not-accessible | The Device Control application entry. | |
| INT deviceControlTcpAliveCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.1 | INTEGER | read-write | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection. |
| INT deviceControlMaxConnection | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.2 | INTEGER | read-write | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort 6000 series device server, and the Real COM driver on that host will have full control over the port. Max. connection = 1: Allows only a single hosts Real COM driver to open the specific NPort 6000 series device servers serial port. Max connection = 2 to 8: Allows 2 to 8 hosts Real COM drivers to open the specific NPort 6000 series device servers serial port, at the same time. When multiple hosts Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of getting the settings from your application program (AP). |
| INT deviceControlIgnoreJammedIp | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.3 | INTEGER | read-write | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts. |
| INT deviceControlAllowDriverControl | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.4 | INTEGER | read-write | If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort 6000 series device server may get configuration changes from multiple hosts, the most recent command received will take precedence. |
| INT deviceControlSecure | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.5 | INTEGER | read-write | If 'Secure' is enabled, the data on the Ethernet will be encrypted with SSL. |
| INT deviceControlTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.6 | INTEGER | read-write | The 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 6000 series device server. |
| INT deviceControlConnectionDownRTS | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.7 | INTEGER | read-write | For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the NPort 6000 series device server. If this setting is set to 'goes low,' RTS will change its state to low if the Ethernet link is off. |
| INT deviceControlConnectionDownDTR | 1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.8 | INTEGER | read-write | For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the NPort 6000 series device server. If this setting is set to 'goes low,' DTR will change its state to low if the Ethernet link is off. |
| socket | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2 | |||
| socketTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1 | not-accessible | The Socket application table. | |
| socketEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1 | not-accessible | The Socket application entry. | |
| INT socketTcpAliveCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.1 | INTEGER | read-write | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection. |
| INT socketInactivityTime | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.2 | INTEGER | read-write | 0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection. |
| INT socketMaxConnection | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.3 | INTEGER | read-write | Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort 6000 series device server, and the Real COM driver on that host will have full control over the port. Max. connection 1: Allows only a single hosts Real COM driver to open the specific NPort 6000 series device servers serial port. Max connection 2 to 8: Allows 2 to 8 hosts Real COM drivers to open the specific NPort 6000 series device servers serial port, at the same time. When multiple hosts Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of depending on your application program (AP). |
| INT socketIgnoreJammedIp | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.4 | INTEGER | read-write | Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts. |
| INT socketAllowDriverControl | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.5 | INTEGER | read-write | If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort 6000 series device server may get configuration changes from multiple hosts, the most recent command received will take precedence. |
| INT socketSecure | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.6 | INTEGER | read-write | If Secure is enabled, data sent over the Ethernet will be encrypted with SSL. |
| INT socketTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.7 | INTEGER | read-write | The 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 6000 series device server. |
| INT socketCmdPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.8 | INTEGER | read-write | The 'Command port' is a TCP port used to listen for IP-Serial Lib commands from the host. In order to prevent a TCP port conflict with other applications, the user can set the Command port to another port if needed. IP-Serial Lib will automatically check the Command Port on the NPort 6000 series device server to avoid the need for the user to configure the program. |
| INT socketTcpServerConnectionDownRTS | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.9 | INTEGER | read-write | For some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the NPort 6000 series device server. If this setting is set to 'goes low,' RTS will change the state to low if the Ethernet link is off. |
| INT socketTcpServerConnectionDownDTR | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.10 | INTEGER | read-write | For some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the NPort 6000 series device server. If this setting is set to 'goes low,' DTR will change the state to low if the Ethernet link is off. |
| STR socketTcpClientDestinationAddress1 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.11 | DisplayString | read-write | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| INT socketTcpClientDestinationPort1 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.12 | INTEGER | read-write | The NPort 6000 series device server can connect actively to a remote host that has this TCP port number. |
| STR socketTcpClientDestinationAddress2 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.13 | DisplayString | read-write | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| INT socketTcpClientDestinationPort2 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.14 | INTEGER | read-write | The NPort 6000 series device server can connect actively to a remote host that has this TCP port number. |
| STR socketTcpClientDestinationAddress3 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.15 | DisplayString | read-write | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| INT socketTcpClientDestinationPort3 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.16 | INTEGER | read-write | The NPort 6000 series device server can connect actively to a remote host that has this port number. |
| STR socketTcpClientDestinationAddress4 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.17 | DisplayString | read-write | The NPort 6000 series device server can connect actively to a remote host that has this IP address. |
| INT socketTcpClientDestinationPort4 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.18 | INTEGER | read-write | The NPort 6000 series device server can connect actively to a remote host that has this port number. |
| INT socketTcpClientDesignatedLocalPort1 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.19 | INTEGER | read-write | The local TCP port used to connect actively to the remote host. |
| INT socketTcpClientDesignatedLocalPort2 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.20 | INTEGER | read-write | The local TCP port used to connect actively to the remote host. |
| INT socketTcpClientDesignatedLocalPort3 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.21 | INTEGER | read-write | The local TCP port used to connect actively to the remote host. |
| INT socketTcpClientDesignatedLocalPort4 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.22 | INTEGER | read-write | The local TCP port used to connect actively to the remote host. |
| INT socketTcpClientConnectionControl | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.23 | INTEGER | read-write | Events that cause the TCP client to drop the connection. |
| IP socketUdpDestinationAddress1Begin | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.24 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress1End. |
| IP socketUdpDestinationAddress1End | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.25 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress1Begin and this parameter. |
| INT socketUdpDestinationPort1 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.26 | INTEGER | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts that have this port number. |
| IP socketUdpDestinationAddress2Begin | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.27 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress2End. |
| IP socketUdpDestinationAddress2End | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.28 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to the remote hosts whose IP addresses are in the range between socketUdpDestinationAddress2Begin and this parameter. |
| INT socketUdpDestinationPort2 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.29 | INTEGER | read-write | The NPort 6000 series device server can actively send UDP packets to the remote hosts that have this TCP port number. |
| IP socketUdpDestinationAddress3Begin | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.30 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress3End. |
| IP socketUdpDestinationAddress3End | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.31 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress3Begin and this parameter. |
| INT socketUdpDestinationPort3 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.32 | INTEGER | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number. |
| IP socketUdpDestinationAddress4Begin | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.33 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress4End. |
| IP socketUdpDestinationAddress4End | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.34 | IpAddress | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress4Begin and this parameter. |
| INT socketUdpDestinationPort4 | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.35 | INTEGER | read-write | The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number. |
| INT socketUdpLocalListenPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.36 | INTEGER | read-write | The UDP port that the NPort 6000 series device server listens to and that other devices must use to contact the NPort 6000 series device server. |
| pairConnection | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3 | |||
| pairConnectionTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1 | not-accessible | The Pair Connection table. | |
| pairConnectionEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1 | not-accessible | The Pair Connection entry. | |
| INT pairConnectionTcpAliveCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.1 | INTEGER | read-write | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection. |
| INT pairConnectionSecure | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.2 | INTEGER | read-write | If Secure is enabled, the Ethernet data will be encrypted using SSL. |
| STR pairConnectionDestinationAddress | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.3 | DisplayString | read-write | The Pair Connection 'Master' will contact the network host that has the specified IP address. |
| INT pairConnectionDestinationPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.4 | INTEGER | read-write | Data will be transmitted through the specified port number. Note that you must configure the same TCP port number for the device server acting as the Pair Connection 'Slave.' |
| INT pairConnectionTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.5 | INTEGER | read-write | This port number must be the same port number that was set up for the Pair Connection 'Master' device server. |
| ethernetModem | 1.3.6.1.4.1.8691.2.8.1.4.1.2.4 | |||
| ethernetModemTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1 | not-accessible | The Ethernet Modem table. | |
| ethernetModemEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1 | not-accessible | The Ethernet Modem entry. | |
| INT ethernetModemTcpAliveCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.1 | INTEGER | read-write | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection. |
| INT ethernetModemTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.2 | INTEGER | read-write | The local TCP port used to listen for incoming calls from a remote ethernet modem. |
| terminal | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5 | |||
| terminalTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1 | not-accessible | The Terminal Application table. | |
| terminalEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1 | not-accessible | The Terminal Application entry. | |
| INT terminalTcpAliveCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.1 | INTEGER | read-write | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection from another host. |
| INT terminalInactivityTime | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.2 | INTEGER | read-write | 0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another host's TCP connection. |
| INT terminalAutoLinkProtocol | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.3 | INTEGER | read-write | If Auto-Link protocol is set to 'None,' the NPort 6000 series device server will not connect to the host automatically. If Auto-Link protocol is set to 'Telnet,' the NPort 6000 series device server will connect to the host automatically using Telnet. If Auto-Link protocol is set to 'Rlogin,' the NPort 6000 series device server will connect to the host automatically using rlogin. |
| STR terminalPrimaryHostAddress | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.4 | DisplayString | read-write | If specified, designates a 'permanent' host to which the terminal will always be connected. |
| STR terminalSecondHostAddress | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.5 | DisplayString | read-write | If specified, designates a 'permanent' host to which the terminal will always be connected. |
| INT terminalTelnetTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.6 | INTEGER | read-write | By default, the Telnet TCP port number is set to 23, which is the default TCP port number for Telnet. If you need to telnet to this NPort 6000 series device server's serial port, set the Telnet TCP port to a different number. |
| INT terminalSshTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.7 | INTEGER | read-write | By default, the SSH TCP port number is set to 22, which is the default TCP port number for SSH. If you need to use SSH to connect to this NPort 6000 series device server's serial port, set the Telnet TCP port to a different number. |
| STR terminalType | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.8 | DisplayString | read-write | Defines the terminal type for outgoing connections. |
| INT terminalMaxSessions | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.9 | INTEGER | read-write | Configure the max. number of sessions. |
| STR terminalChangeSession | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.10 | DisplayString | read-write | Defines the control character used to change the terminal session. |
| STR terminalQuit | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.11 | DisplayString | read-write | Defines the control character used to quit a terminal session. |
| STR terminalBreak | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.12 | DisplayString | read-write | Defines the control character used to send a Telnet BREAK message. |
| STR terminalInterrupt | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.13 | DisplayString | read-write | Defines the control character used to send a Telnet INTERRUPT message. |
| INT terminalAuthenticationType | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.14 | INTEGER | read-write | The terminal authentication type. |
| STR terminalAutoLoginPrompt | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.15 | DisplayString | read-write | The prompt string for the automatic login ID. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will automatically reply with the user ID. |
| STR terminalPasswordPrompt | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.16 | DisplayString | read-write | The prompt string for the automatic login password. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will automatically reply with the user password. |
| STR terminalLoginUserName | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.17 | DisplayString | read-write | Terminal login ID for automatic login. |
| STR terminalLoginPassword | 1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.18 | DisplayString | read-write | Terminal login password for automatic login. |
| reverseTerminal | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6 | |||
| reverseTerminalTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1 | not-accessible | The Reverse Terminal Application table. | |
| reverseTerminalEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1 | not-accessible | The Reverse Terminal Application entry. | |
| INT reverseTerminalTcpAliveCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.1 | INTEGER | read-write | The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection. |
| INT reverseTerminalInactivityTime | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.2 | INTEGER | read-write | 0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection. |
| INT reverseTerminalTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.3 | INTEGER | read-write | Each of the NPort 6000 series device server's serial ports are mapped to a TCP port. |
| INT reverseTerminalAuthenticationType | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.4 | INTEGER | read-write | The reverse terminal authentication type. |
| INT reverseTerminalMapKeys | 1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.5 | INTEGER | read-write | If data received through NPort 6000 series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out through the serial port with an added 1. 'carriage return + line feed' if you select the 'cr-lf' option (i.e., the cursor will jump to the next line, and return to the first character of the line) 2. 'carriage return' if you select the 'cr' option (i.e., the cursor will return to the first character of the line 3. 'line feed' if you select the 'lf' option. (i.e., the cursor will jump to the next line, but not move horizontally) |
| printer | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7 | |||
| printerTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1 | not-accessible | The Printer Application table. | |
| printerEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1 | not-accessible | The Printer Application entry. | |
| INT printerTcpAliveCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.1 | INTEGER | read-write | The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection. |
| INT printerTcpPort | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.2 | INTEGER | read-only | The host uses this value to determine the Group to which the printer attached to this serial port belongs. These values are fixed, and cannot be changed by the user. |
| INT printerGroup | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.3 | INTEGER | read-write | Groups printers attached to different ports. Printers in the same group will share the printing load for printing requests to that group of printers. E.g., setting the NPort 6000 series device server's serial ports 1, 3, and 6 for 'Group01' will allow the printers attached to these three ports to act essentially as one printer. |
| STR printerQueueNameRaw | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.4 | DisplayString | read-write | Specify the name of the print queue (in RAW mode). |
| STR printerQueueNameASCII | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.5 | DisplayString | read-write | Specify the name of the print queue (in ASCII mode). |
| INT printerAppendFromFeed | 1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.6 | INTEGER | read-write | Specify paging. |
| dial | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8 | |||
| dialTable | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1 | not-accessible | The Dial In/Out table. | |
| dialEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1 | not-accessible | The Dial In/Out entry. | |
| INT dialTERMBINMode | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.1 | INTEGER | read-write | Select Yes to enable a Binary Terminal connection. |
| INT dialPPPDMode | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.2 | INTEGER | read-write | Select Yes to enable a PPPD connection. |
| INT dialSLIPDMode | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.3 | INTEGER | read-write | Select Yes to enable a SLIPD Terminal connection. |
| INT dialAuthType | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.4 | INTEGER | read-write | The dial in/out authentication type. |
| INT dialDisconnectBy | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.5 | INTEGER | read-write | If this field is set to 'dcd-off,' the connection will be disconnected when the DCD signal is off. If this field is set to 'dsr-off,' the connection will be disconnected when the DSR signal is off. |
| IP dialDestinationIpAddress | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.6 | IpAddress | read-write | Destination IP address is the IP address of the remote dial-in/dial-out server. |
| IP dialSourceIpAddress | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.7 | IpAddress | read-write | Source IP address is IP address of this serial port. The NPort 6000 series device server will automatically assign an IP address for the port. We recommend leaving this field blank. |
| IP dialIpNetmask | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.8 | IpAddress | read-write | The IP netmask used for dial-in/dial-out networks (PPP or SLIP). |
| INT dialTcpIpCompression | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.9 | INTEGER | read-write | Depends on whether the remote user's application requests compression. |
| INT dialInactivityTime | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.10 | INTEGER | read-write | 0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection. |
| INT dialLinkQualityReport | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.11 | INTEGER | read-write | Choose YES if you are using software to collect Link quality information. |
| STR dialOutgoingPAPID | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.12 | DisplayString | read-write | Dial-out user ID account. |
| STR dialPAPPassword | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.13 | DisplayString | read-write | Dial-out user password. |
| INT dialIncomingPAPCheck | 1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.14 | INTEGER | read-write | The Dial in/out incoming PAP check type. |
| dataPacking | 1.3.6.1.4.1.8691.2.8.1.4.1.3 | |||
| dataPackingPortTable | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1 | not-accessible | The Data Packing table. | |
| dataPackingPortEntry | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1 | not-accessible | The Data Packing entry. | |
| INT portPacketLength | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.1 | INTEGER | read-write | If the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value, the data will be forced out. The data length can be configured from 0 to 1024 bytes. Set to 0 if you do not need to limit the length. |
| INT portDelimiter1Enable | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.2 | INTEGER | read-write | Enable the first delimiter character. |
| STR portDelimiter1 | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.3 | DisplayString | read-write | The first delimiter character, in hex decimal. |
| INT portDelimiter2Enable | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.4 | INTEGER | read-write | Enable the second delimiter character. |
| STR portDelimiter2 | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.5 | DisplayString | read-write | The second delimiter character, in hex decimal. |
| INT portDelimiterProcess | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.6 | INTEGER | read-write | 'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterAddTwo') of data is received after receiving the Delimiter. 'stripDelimiter': When the delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining data is transmitted. 'doNothing': The data will be transmitted when the delimiter is received. |
| INT portForceTransmit | 1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.7 | INTEGER | read-write | 0: Disable the force transmit timeout. 1 to 65535: Forces the NPort 6000 series device server's TCP/IP protocol software to try to pack serial data received during the specified time into the same data frame. |
| comParamSetting | 1.3.6.1.4.1.8691.2.8.1.4.2 | |||
| comParamPortTable | 1.3.6.1.4.1.8691.2.8.1.4.2.1 | not-accessible | The Communication Parameters table. | |
| comParamPortEntry | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1 | not-accessible | The Communication Parameters entry. | |
| STR portAlias | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.1 | DisplayString | read-write | Port alias is included to allow easy identification of the serial devices that are connected to NPort 6000 series device server's serial port. |
| INT portInterface | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.2 | INTEGER | read-write | The serial interface that the port works on. |
| INT portBaudRate | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.3 | INTEGER | read-write | The port's speed in bits per second. You can choose a standard baud rate by indexing. |
| INT portBaudRateManual | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.4 | INTEGER | read-write | The port's speed in bits per second. You can specify a baud rate manually. |
| INT portDataBits | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.5 | INTEGER | read-write | The number of bits in a character for the port. |
| INT portStopBits | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.6 | INTEGER | read-write | The number of stop bits for the port. |
| INT portParity | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.7 | INTEGER | read-write | The parity bit for the port. |
| INT portFlowControl | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.8 | INTEGER | read-write | The flow-control method for the port. |
| INT portFIFO | 1.3.6.1.4.1.8691.2.8.1.4.2.1.1.9 | INTEGER | read-write | Enable or disable the port's FIFO. |
| dataBuffering | 1.3.6.1.4.1.8691.2.8.1.4.3 | |||
| dataBufferingPortTable | 1.3.6.1.4.1.8691.2.8.1.4.3.1 | not-accessible | The Data Buffering/Log table. | |
| dataBufferingPortEntry | 1.3.6.1.4.1.8691.2.8.1.4.3.1.1 | not-accessible | The Data Buffering/Log entry. | |
| INT portBufferingEnable | 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.1 | INTEGER | read-write | Enable off-line port buffering. |
| INT portBufferingLocation | 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.2 | INTEGER | read-write | The location of off-line port buffering. |
| INT portBufferingSDFileSize | 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.3 | INTEGER | read-write | The maximum file size of off-line port buffering, in MBytes, if the location is set to 'sdCard.' |
| INT portSerialDataLoggingEnable | 1.3.6.1.4.1.8691.2.8.1.4.3.1.1.4 | INTEGER | read-write | Enable or disable serial data logging for the port. |
| modemSettings | 1.3.6.1.4.1.8691.2.8.1.4.4 | |||
| modemSettingsPortTable | 1.3.6.1.4.1.8691.2.8.1.4.4.1 | not-accessible | The Modem Settings table. | |
| modemSettingsPortEntry | 1.3.6.1.4.1.8691.2.8.1.4.4.1.1 | not-accessible | The Modem Settings entry. | |
| INT portEnableModem | 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.1 | INTEGER | read-write | Enable or disable modem for this port. |
| STR portInitialString | 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.2 | DisplayString | read-write | Set the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer. |
| STR portDialUp | 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.3 | DisplayString | read-write | Set the modem's dial-up AT command string. |
| STR portPhoneNumber | 1.3.6.1.4.1.8691.2.8.1.4.4.1.1.4 | DisplayString | read-write | Set the number used to dial out. |
| welcomeMessage | 1.3.6.1.4.1.8691.2.8.1.4.5 | |||
| INT portEnableWelcomeMessage | 1.3.6.1.4.1.8691.2.8.1.4.5.1 | INTEGER | read-write | Enable or disable the welcome message. |
| STR portMessage | 1.3.6.1.4.1.8691.2.8.1.4.5.2 | DisplayString | read-write | Set up a welcome message to greet dial-in users. |
| sysManagement | 1.3.6.1.4.1.8691.2.8.1.5 | |||
| miscNetworkSettings | 1.3.6.1.4.1.8691.2.8.1.5.1 | |||
| accessibleIp | 1.3.6.1.4.1.8691.2.8.1.5.1.1 | |||
| INT enableAccessibleIpList | 1.3.6.1.4.1.8691.2.8.1.5.1.1.1 | INTEGER | read-write | Enable or disable the entire accessible IP list. |
| accessibleIpListTable | 1.3.6.1.4.1.8691.2.8.1.5.1.1.2 | not-accessible | Accessible IP List table. | |
| accessibleIpListEntry | 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1 | not-accessible | Accessible IP List entry. | |
| INT accessibleIpListIndex | 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.1 | INTEGER | read-only | Accessible IP List index. |
| INT activeAccessibleIpList | 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.2 | INTEGER | read-write | Enable or disable this accessible IP entry. |
| IP accessibleIpListAddress | 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.3 | IpAddress | read-write | Accessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address. |
| IP accessibleIpListNetmask | 1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.4 | IpAddress | read-write | Accessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts. |
| snmpAgentSettings | 1.3.6.1.4.1.8691.2.8.1.5.1.2 | |||
| INT snmpEnable | 1.3.6.1.4.1.8691.2.8.1.5.1.2.1 | INTEGER | read-write | Enable or disable SNMP agent. |
| STR snmpContactName | 1.3.6.1.4.1.8691.2.8.1.5.1.2.2 | DisplayString | read-write | The SNMP contact information usually includes an emergency contact name and telephone or pager number. |
| STR snmpLocation | 1.3.6.1.4.1.8691.2.8.1.5.1.2.3 | DisplayString | read-write | Specify the location string for SNMP agents, such as the NPort 6000 series device server. This string is usually set to the street address where the NPort 6000 series device server is physically located. |
| dDNS | 1.3.6.1.4.1.8691.2.8.1.5.1.3 | |||
| INT dDNSEnable | 1.3.6.1.4.1.8691.2.8.1.5.1.3.1 | INTEGER | read-write | Enable or disable the DDNS function. |
| INT dDNSServerAddress | 1.3.6.1.4.1.8691.2.8.1.5.1.3.2 | INTEGER | read-write | The DDNS server address. The DDNS is serviced by a 3-party provider. To use the DDNS function, you may need to obtain a user account from the server. |
| STR dDNSHostName | 1.3.6.1.4.1.8691.2.8.1.5.1.3.3 | DisplayString | read-write | The host name of the machine to be registered to the DDNS server. |
| STR dDNSUserName | 1.3.6.1.4.1.8691.2.8.1.5.1.3.4 | DisplayString | read-write | The user account provided by the DDNS server. |
| STR dDNSPassword | 1.3.6.1.4.1.8691.2.8.1.5.1.3.5 | DisplayString | read-write | The user password provided by the DDNS server. |
| hostTable | 1.3.6.1.4.1.8691.2.8.1.5.1.4 | |||
| hostTableTable | 1.3.6.1.4.1.8691.2.8.1.5.1.4.1 | not-accessible | Host Table. | |
| hostTableEntry | 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1 | not-accessible | Host Table entry. | |
| INT hostTableIndex | 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.1 | INTEGER | read-only | The Host Table index. |
| STR hostName | 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.2 | DisplayString | read-write | The host name of the host table entry. |
| IP hostIpAddress | 1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.3 | IpAddress | read-write | Related IP address of the host table entry. |
| routeTable | 1.3.6.1.4.1.8691.2.8.1.5.1.5 | |||
| routeTableTable | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1 | not-accessible | Route Table. | |
| routeTableEntry | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1 | not-accessible | Route Table entry. | |
| INT routeTableIndex | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.1 | INTEGER | read-only | The Route Table index. |
| IP gatewayRouteTable | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.2 | IpAddress | read-write | The gateway property of the route table entry. |
| IP destinationRouteTable | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.3 | IpAddress | read-write | The destination IP address of the route table entry. This value can be the IP address of a single host if the netmask set to '255.255.255.255,' or it can be a network address. |
| IP netmaskRouteTable | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.4 | IpAddress | read-write | The destination netmask of the route table entry. |
| INT metricRouteTable | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.5 | INTEGER | read-write | The routing metric for this route. The semantics of this metric are determined by the routing-protocol. Normally, it represents the cost for the destination. |
| INT interfaceRouteTable | 1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.6 | INTEGER | read-write | The value that identifies the local interface through which the next hop of this route should be reached. |
| userTable | 1.3.6.1.4.1.8691.2.8.1.5.1.6 | |||
| userTableTable | 1.3.6.1.4.1.8691.2.8.1.5.1.6.1 | not-accessible | User Table. | |
| userTableEntry | 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1 | not-accessible | User Table entry. | |
| INT userTableIndex | 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.1 | INTEGER | read-only | The User Table index. |
| STR userNameUserTable | 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.2 | DisplayString | read-write | The user name of this entry. |
| STR passwordUserTable | 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.3 | DisplayString | read-write | The password of this user entry. |
| STR phoneNumberUserTable | 1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.4 | DisplayString | read-write | The phone number of this user entry. |
| authenticationServer | 1.3.6.1.4.1.8691.2.8.1.5.1.7 | |||
| STR radiusServerIp | 1.3.6.1.4.1.8691.2.8.1.5.1.7.1 | DisplayString | read-write | The IP address or domain name of the RADIUS server. |
| STR radiusKey | 1.3.6.1.4.1.8691.2.8.1.5.1.7.2 | DisplayString | read-write | RADIUS password. Must be the same as in the RADIUS server. |
| INT udpPortAuthenticationServer | 1.3.6.1.4.1.8691.2.8.1.5.1.7.3 | INTEGER | read-write | The UDP port of the RADIUS server. |
| INT radiusAccounting | 1.3.6.1.4.1.8691.2.8.1.5.1.7.4 | INTEGER | read-write | Enable or disable RADIUS accounting. |
| sysLogSettings | 1.3.6.1.4.1.8691.2.8.1.5.1.8 | |||
| INT sysLocalLog | 1.3.6.1.4.1.8691.2.8.1.5.1.8.1 | INTEGER | read-write | Log the following events to the system log: System Cold Start, System Warm Start. |
| INT networkLocalLog | 1.3.6.1.4.1.8691.2.8.1.5.1.8.2 | INTEGER | read-write | Log the following events to the system log: DHCP/BOOTP/PPPoE Get IP/Renew, NTP, Mail Fail, NTP Connect Fail, DHCP Fail, IP Conflict, Ethernet Link Down. |
| INT configLocalLog | 1.3.6.1.4.1.8691.2.8.1.5.1.8.3 | INTEGER | read-write | Log the following events to the system log: Login Fail, IP Changed, Password Changed, Config Changed, Firmware Upgrade, SSL Key Import, Config Import, Config Export. |
| INT opModeLocalLog | 1.3.6.1.4.1.8691.2.8.1.5.1.8.4 | INTEGER | read-write | Log the following op-mode events to the system log: Connect, Disconnect, Authentication Fail, Restart. |
| autoWarningSettings | 1.3.6.1.4.1.8691.2.8.1.5.2 | |||
| eventSettings | 1.3.6.1.4.1.8691.2.8.1.5.2.1 | |||
| INT mailWarningColdStart | 1.3.6.1.4.1.8691.2.8.1.5.2.1.1 | INTEGER | read-write | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatically issue an auto warning message by e-mail after booting up. |
| INT mailWarningWarmStart | 1.3.6.1.4.1.8691.2.8.1.5.2.1.2 | INTEGER | read-write | Refers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an e-mail after rebooting. |
| INT mailWarningAuthFailure | 1.3.6.1.4.1.8691.2.8.1.5.2.1.3 | INTEGER | read-write | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately send an e-mail. |
| INT mailWarningIpChanged | 1.3.6.1.4.1.8691.2.8.1.5.2.1.4 | INTEGER | read-write | The user has changed the NPort 6000 series device server's IP address. When the IP address changes, the NPort 6000 series device server will send an e-mail with the new IP address before it reboots. If the NPort 6000 series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning. |
| INT mailWarningPasswordChanged | 1.3.6.1.4.1.8691.2.8.1.5.2.1.5 | INTEGER | read-write | The user has changed the NPort 6000 series device server's password. When the password changes, the NPort 6000 series device server will send an e-mail with the password changed notice before it reboots. If the NPort 6000 series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning. |
| INT trapServerColdStart | 1.3.6.1.4.1.8691.2.8.1.5.2.1.6 | INTEGER | read-write | Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatically issue an auto warning message by sending an SNMP trap after booting up. |
| INT trapServerWarmStart | 1.3.6.1.4.1.8691.2.8.1.5.2.1.7 | INTEGER | read-write | Refers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an SNMP trap after rebooting. |
| INT trapServerAuthFailure | 1.3.6.1.4.1.8691.2.8.1.5.2.1.8 | INTEGER | read-write | The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately send an SNMP trap. |
| INT alarmServerEthernet1LinkDown | 1.3.6.1.4.1.8691.2.8.1.5.2.1.9 | INTEGER | read-write | When the built-in link1 port is off, the NPort 6000 series device server will automatically raise a d-out alarm. |
| INT alarmServerEthernet2LinkDown | 1.3.6.1.4.1.8691.2.8.1.5.2.1.10 | INTEGER | read-write | The NPort 6000 series device server can provide an extra Ethernet port via the network module. When the first port on the network module is off, the NPort 6000 series device server will automatically raise a d-out alarm. |
| INT alarmServerEthernet3LinkDown | 1.3.6.1.4.1.8691.2.8.1.5.2.1.11 | INTEGER | read-write | The NPort 6000 series device server can provide an extra Ethernet port via the network module. When the second port on the network module is off, the NPort 6000 series device server will automatically raise a d-out alarm. |
| serialEventSettings | 1.3.6.1.4.1.8691.2.8.1.5.2.2 | |||
| portEventSettingsTable | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1 | not-accessible | Port Event Settings Table. | |
| portEventSettingsEntry | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1 | not-accessible | Port Event Settings entry. | |
| INT mailDCDchange | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.1 | INTEGER | read-write | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately send an e-mail message. |
| INT trapDCDchange | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.2 | INTEGER | read-write | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately send an SNMP trap. |
| INT alarmDCDchange | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.3 | INTEGER | read-write | A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately raise a d-out alarm. |
| INT mailDSRchange | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.4 | INTEGER | read-write | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately send an e-mail message. |
| INT trapDSRchange | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.5 | INTEGER | read-write | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately send an SNMP trap. |
| INT alarmDSRchange | 1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.6 | INTEGER | read-write | A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately raise a d-out alarm. |
| emailAlert | 1.3.6.1.4.1.8691.2.8.1.5.2.3 | |||
| STR emailWarningMailServer | 1.3.6.1.4.1.8691.2.8.1.5.2.3.1 | DisplayString | read-write | The e-mail server's IP address or domain name of the e-mail warning function. |
| INT emailRequiresAuthentication | 1.3.6.1.4.1.8691.2.8.1.5.2.3.2 | INTEGER | read-write | Set if the mail server requires user login. |
| STR emailWarningUserName | 1.3.6.1.4.1.8691.2.8.1.5.2.3.3 | DisplayString | read-write | The user name used to log into the mail server if authentication is required. |
| STR emailWarningPassword | 1.3.6.1.4.1.8691.2.8.1.5.2.3.4 | DisplayString | read-write | The password used to log into the mail server if authentication is required. |
| STR emailWarningFromEmail | 1.3.6.1.4.1.8691.2.8.1.5.2.3.5 | DisplayString | read-write | The e-mail address to be filled in the 'From' field of the auto-warning e-mail. |
| STR emailWarningFirstEmailAddr | 1.3.6.1.4.1.8691.2.8.1.5.2.3.6 | DisplayString | read-write | The first email address to where the auto-warning e-mail is to be sent. |
| STR emailWarningSecondEmailAddr | 1.3.6.1.4.1.8691.2.8.1.5.2.3.7 | DisplayString | read-write | The second email address to where the auto-warning e-mail is to be sent. |
| STR emailWarningThirdEmailAddr | 1.3.6.1.4.1.8691.2.8.1.5.2.3.8 | DisplayString | read-write | The third email address to where the auto-warning e-mail is to be sent. |
| STR emailWarningFourthEmailAddr | 1.3.6.1.4.1.8691.2.8.1.5.2.3.9 | DisplayString | read-write | The fourth email address to where the auto-warning e-mail is to be sent. |
| snmpTrap | 1.3.6.1.4.1.8691.2.8.1.5.2.4 | |||
| STR snmpTrapReceiverIp | 1.3.6.1.4.1.8691.2.8.1.5.2.4.1 | DisplayString | read-write | SNMP trap receiver IP address or domain name. |
| INT trapVersion | 1.3.6.1.4.1.8691.2.8.1.5.2.4.2 | INTEGER | read-write | SNMP trap version used for the auto-warning function. |
| maintenance | 1.3.6.1.4.1.8691.2.8.1.5.3 | |||
| consoleSettings | 1.3.6.1.4.1.8691.2.8.1.5.3.1 | |||
| INT httpConsole | 1.3.6.1.4.1.8691.2.8.1.5.3.1.1 | INTEGER | read-write | Enable or disable HTTP console. |
| INT httpsConsole | 1.3.6.1.4.1.8691.2.8.1.5.3.1.2 | INTEGER | read-write | Enable or disable HTTPS console. |
| INT telnetConsole | 1.3.6.1.4.1.8691.2.8.1.5.3.1.3 | INTEGER | read-write | Enable or disable Telnet console. |
| INT sshConsole | 1.3.6.1.4.1.8691.2.8.1.5.3.1.4 | INTEGER | read-write | Enable or disable SSH console. |
| INT lcmReadOnlyProtect | 1.3.6.1.4.1.8691.2.8.1.5.3.1.5 | INTEGER | read-write | Enable or disable LCM read-only protection. If the LCM panel is under read-only protection, users can only view the configurations from the LCM panel. Otherwise, by default, users can modify the settings directly on the LCM panel. |
| INT resetButtonFunction | 1.3.6.1.4.1.8691.2.8.1.5.3.1.6 | INTEGER | read-write | Enable or disable reset button protection. You can disable the hardware reset button after the NPort 6000 series device server has been restarted for 60 seconds. |
| loadFactoryDefault | 1.3.6.1.4.1.8691.2.8.1.5.3.2 | |||
| INT loadFactoryDefaultSetting | 1.3.6.1.4.1.8691.2.8.1.5.3.2.1 | INTEGER | write-only | This function will reset all of the NPort 6000 series device server's settings to the factory default values. Be aware that previous settings will be lost. Selecting Reset to factory default (excluding IP configuration) will reset all settings except the IP configuration to factory defaults. Selecting Reset to factory default will reset all settings including the IP configuration to factory defaults. |
| sysStatus | 1.3.6.1.4.1.8691.2.8.1.6 | |||
| s2eConnections | 1.3.6.1.4.1.8691.2.8.1.6.1 | |||
| monitorRemoteIpTable | 1.3.6.1.4.1.8691.2.8.1.6.1.1 | not-accessible | Serial to Network Connections Remote IP table. | |
| monitorRemoteIpEntry | 1.3.6.1.4.1.8691.2.8.1.6.1.1.1 | not-accessible | Serial to Network Connections Remote IP entry. | |
| INT remoteIpIndex | 1.3.6.1.4.1.8691.2.8.1.6.1.1.1.1 | INTEGER | read-only | Serial to Network Connections Remote IP index. |
| IP monitorRemoteIp | 1.3.6.1.4.1.8691.2.8.1.6.1.1.1.2 | IpAddress | read-only | The remote IP currently connecting to this port. |
| serialPortStatus | 1.3.6.1.4.1.8691.2.8.1.6.2 | |||
| monitorSerialPortStatusTable | 1.3.6.1.4.1.8691.2.8.1.6.2.1 | not-accessible | Serial Port Status table. | |
| monitorSerialPortStatusEntry | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1 | not-accessible | Serial Port Status entry. | |
| INT monitorTxCount | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.1 | INTEGER | read-only | View the number of bytes transmitted from the port since the last time the port was initialized. |
| INT monitorRxCount | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.2 | INTEGER | read-only | View the number of bytes received by the port since the last time the port was initialized. |
| INT monitorTxTotalCount | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.3 | INTEGER | read-only | View the number of bytes transmitted from the port since the last time the system was initialized. |
| INT monitorRxTotalCount | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.4 | INTEGER | read-only | View the number of bytes received by the port since the last time the system was initialized. |
| INT monitorDSR | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.5 | INTEGER | read-only | View the current DSR status of this port. |
| INT monitorDTR | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.6 | INTEGER | read-only | View the current DTR status of this port. |
| INT monitorRTS | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.7 | INTEGER | read-only | View the current RTS status of this port. |
| INT monitorCTS | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.8 | INTEGER | read-only | View the current CTS status of this port. |
| INT monitorDCD | 1.3.6.1.4.1.8691.2.8.1.6.2.1.1.9 | INTEGER | read-only | View the current DCD status of this port. |
| serialPortErrorCount | 1.3.6.1.4.1.8691.2.8.1.6.3 | |||
| monitorSerialPortErrorCountTable | 1.3.6.1.4.1.8691.2.8.1.6.3.1 | not-accessible | Serial Port Error Count table. | |
| monitorSerialPortErrorCountEntry | 1.3.6.1.4.1.8691.2.8.1.6.3.1.1 | not-accessible | Serial Port Error Count entry. | |
| INT monitorErrorCountFrame | 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.1 | INTEGER | read-only | View the number of 'Frame' errors for this port. |
| INT monitorErrorCountParity | 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.2 | INTEGER | read-only | View the number of 'Parity' errors for this port. |
| INT monitorErrorCountOverrun | 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.3 | INTEGER | read-only | View the number of 'Overrun' errors for this port. |
| INT monitorErrorCountBreak | 1.3.6.1.4.1.8691.2.8.1.6.3.1.1.4 | INTEGER | read-only | View the number of 'Break' errors for this port. |
| serialPortSettings | 1.3.6.1.4.1.8691.2.8.1.6.4 | |||
| monitorSerialPortSettingsTable | 1.3.6.1.4.1.8691.2.8.1.6.4.1 | not-accessible | Serial Port Settings table. | |
| monitorSerialPortSettingsEntry | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1 | not-accessible | Serial Port Settings entry. | |
| INT monitorBaudRate | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.1 | INTEGER | read-only | View the current baudrate of the port. |
| INT monitorDataBits | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.2 | INTEGER | read-only | View the number of bits per byte for the port. |
| STR monitorStopBits | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.3 | DisplayString | read-only | View the number of stop bits for the port. |
| INT monitorParity | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.4 | INTEGER | read-only | View the parity bit for the port. |
| INT monitorRTSCTSFlowControl | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.5 | INTEGER | read-only | View if the port is using RTS/CTS flow control. |
| INT monitorXONXOFFFlowControl | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.6 | INTEGER | read-only | View if the port is using XON/XOFF flow control. |
| INT monitorDTRDSRFlowControl | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.7 | INTEGER | read-only | View if the port is using DTR/DSR flow control. |
| INT monitorFIFO | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.8 | INTEGER | read-only | View FIFO status of this port. |
| INT monitorInterface | 1.3.6.1.4.1.8691.2.8.1.6.4.1.1.9 | INTEGER | read-only | View the serial interface that the port is using. |
| relayOutputStatus | 1.3.6.1.4.1.8691.2.8.1.6.5 | |||
| INT relayOutputEthernet1LinkDown | 1.3.6.1.4.1.8691.2.8.1.6.5.1 | INTEGER | read-only | The relay dout status of the event that the built- in LAN port is off. |
| INT ethernet1LinkDownAcknowledge | 1.3.6.1.4.1.8691.2.8.1.6.5.2 | INTEGER | write-only | Acknowledge the event that the built-in LAN port is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| INT relayOutputEthernet2LinkDown | 1.3.6.1.4.1.8691.2.8.1.6.5.3 | INTEGER | read-only | The relay dout status of the event that the first LAN port of the network module is off. |
| INT ethernet2LinkDownAcknowledge | 1.3.6.1.4.1.8691.2.8.1.6.5.4 | INTEGER | write-only | Acknowledge the event that the first LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| INT relayOutputEthernet3LinkDown | 1.3.6.1.4.1.8691.2.8.1.6.5.5 | INTEGER | read-only | The relay dout status of the event that the second LAN port of the network module is off. |
| INT ethernet3LinkDownAcknowledge | 1.3.6.1.4.1.8691.2.8.1.6.5.6 | INTEGER | write-only | Acknowledge the event that the second LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| portDCDChangedStatusTable | 1.3.6.1.4.1.8691.2.8.1.6.5.7 | not-accessible | DCD changed table. | |
| portDCDChangedStatusEntry | 1.3.6.1.4.1.8691.2.8.1.6.5.7.1 | not-accessible | DCD changed entry. | |
| INT portDCDChangedStatus | 1.3.6.1.4.1.8691.2.8.1.6.5.7.1.1 | INTEGER | read-only | The relay dout status of the event that the DCD signal of the port is changed. |
| INT portDCDChangedAcknowledge | 1.3.6.1.4.1.8691.2.8.1.6.5.7.1.2 | INTEGER | write-only | Acknowledge the event that the DCD signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| portDSRChangedStatusTable | 1.3.6.1.4.1.8691.2.8.1.6.5.8 | not-accessible | DSR changed Table. | |
| portDSRChangedStatusEntry | 1.3.6.1.4.1.8691.2.8.1.6.5.8.1 | not-accessible | DSR changed entry. | |
| INT portDSRChangedStatus | 1.3.6.1.4.1.8691.2.8.1.6.5.8.1.1 | INTEGER | read-only | The relay dout status of the event that the DSR signal of the port is changed. |
| INT portDSRChangedAcknowledge | 1.3.6.1.4.1.8691.2.8.1.6.5.8.1.2 | INTEGER | write-only | Acknowledge the event that the DSR signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem. |
| saveConfiguration | 1.3.6.1.4.1.8691.2.8.1.7 | |||
| INT saveConfig | 1.3.6.1.4.1.8691.2.8.1.7.1 | INTEGER | write-only | Save the applied configuration to the NPort 6000 series device server. |
| restart | 1.3.6.1.4.1.8691.2.8.1.8 | |||
| INT restartPorts | 1.3.6.1.4.1.8691.2.8.1.8.1 | INTEGER | write-only | Restart serial port. Restarting will cause port reseting. |
| INT restartSystem | 1.3.6.1.4.1.8691.2.8.1.8.2 | INTEGER | write-only | Restart the NPort 6000 series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the changes will be lost. |
RFC description
Management MIB for Moxa NPort 6000 series serial device servers with network interface configuration.
Start monitoring Moxa NPort 6000 series secure serial device server with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.