All MIBs › MRV-IN-REACH-CHARACTER-MIB
Category: Console Servers
Description: Manages MRV In-Reach character-mode serial port sessions and flow control.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MRV-IN-REACH-CHARACTER-MIB?
MRV-IN-REACH-CHARACTER-MIB is a vendor-specific module for MRV Communications' In-Reach family of console/terminal servers, covering the environmental-monitoring and power-management features built into these devices. It exposes environmental sensor data (temperature/humidity and units), contact-closure/alarm inputs, circuit-breaker status, and a controllable power outlet table with per-outlet naming, on/off control, and remote reboot. This makes it strongly oriented toward monitoring physical hardware status: ambient temperature and humidity, external alarm/contact-closure sensor trips, circuit breaker faults, and the operational on/off state (including redundancy) of each managed power outlet. It is part of MRV's proprietary In-Reach MIB family and is typically used alongside the companion In-Reach chassis and Ethernet MIBs for the same device. Typical deployment is data-center or remote-site equipment racks where an In-Reach console server also provides environmental monitoring and remote power-cycling of attached equipment. Engineers can download the MRV-IN-REACH-CHARACTER-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in MRV-IN-REACH-CHARACTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- MRV In-Reach console/terminal server with environmental/power management module
Monitoring Examples
An admin polls basicTemperatureHumiditySensor and basicTemperatureUnits to track ambient rack temperature/humidity, and watches basicContactClosureOrAlarmInputTable (basicContactClosureOrAlarmInputEntry) for a tripped door or alarm contact. basicPowerOutletTable (basicPowerOutletEntry, indexed by basicPowerOutletIndex) exposes basicPowerOutletName and basicPowerOutletOnOff so the admin can remotely power-cycle a hung device via basicPowerOutletReboot, basicPowerOutletRedundant flags whether an outlet is on a redundant feed, and basicEnvironmentalManagerCircuitBreaker reports circuit-breaker trip status for the outlet bank.
What Can Be Monitored
- ambient temperature/humidity
- contact closure/alarm input status
- power outlet on/off status
- circuit breaker status
- redundant outlet indication
This MIB depends on
Related MIBs
Imported Objects
From MRV-IN-REACH-PRODUCT-DIVISION-MIB
| AddressType | |
| DateTime | |
| mrvInReachProductDivision | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| TimeTicks |
From RFC1213-MIB
| DisplayString | |
| sysLocation |
From RFC1316-MIB
| charPortIndex | OBJECT-TYPE |
From RFC1317-MIB
| rs232InSigState | OBJECT-TYPE |
| rs232OutSigState | OBJECT-TYPE |
| rs232PortIndex | OBJECT-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF alarmInputLowDensity0001Alarm | 1.3.6.1.4.1.33.0.10001 | Generated when alarm point 1 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0001Normal | 1.3.6.1.4.1.33.0.20001 | Generated when alarm point 1 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0002Alarm | 1.3.6.1.4.1.33.0.10002 | Generated when alarm point 2 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0002Normal | 1.3.6.1.4.1.33.0.20002 | Generated when alarm point 2 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0003Alarm | 1.3.6.1.4.1.33.0.10003 | Generated when alarm point 3 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0003Normal | 1.3.6.1.4.1.33.0.20003 | Generated when alarm point 3 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0004Alarm | 1.3.6.1.4.1.33.0.10004 | Generated when alarm point 4 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0004Normal | 1.3.6.1.4.1.33.0.20004 | Generated when alarm point 4 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0005Alarm | 1.3.6.1.4.1.33.0.10005 | Generated when alarm point 5 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0005Normal | 1.3.6.1.4.1.33.0.20005 | Generated when alarm point 5 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0006Alarm | 1.3.6.1.4.1.33.0.10006 | Generated when alarm point 6 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0006Normal | 1.3.6.1.4.1.33.0.20006 | Generated when alarm point 6 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0007Alarm | 1.3.6.1.4.1.33.0.10007 | Generated when alarm point 7 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0007Normal | 1.3.6.1.4.1.33.0.20007 | Generated when alarm point 7 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0008Alarm | 1.3.6.1.4.1.33.0.10008 | Generated when alarm point 8 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0008Normal | 1.3.6.1.4.1.33.0.20008 | Generated when alarm point 8 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0009Alarm | 1.3.6.1.4.1.33.0.10009 | Generated when alarm point 9 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0009Normal | 1.3.6.1.4.1.33.0.20009 | Generated when alarm point 9 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0010Alarm | 1.3.6.1.4.1.33.0.10010 | Generated when alarm point 10 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0010Normal | 1.3.6.1.4.1.33.0.20010 | Generated when alarm point 10 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0011Alarm | 1.3.6.1.4.1.33.0.10011 | Generated when alarm point 11 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0011Normal | 1.3.6.1.4.1.33.0.20011 | Generated when alarm point 11 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0012Alarm | 1.3.6.1.4.1.33.0.10012 | Generated when alarm point 12 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0012Normal | 1.3.6.1.4.1.33.0.20012 | Generated when alarm point 12 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0013Alarm | 1.3.6.1.4.1.33.0.10013 | Generated when alarm point 13 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0013Normal | 1.3.6.1.4.1.33.0.20013 | Generated when alarm point 13 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0014Alarm | 1.3.6.1.4.1.33.0.10014 | Generated when alarm point 14 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0014Normal | 1.3.6.1.4.1.33.0.20014 | Generated when alarm point 14 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0015Alarm | 1.3.6.1.4.1.33.0.10015 | Generated when alarm point 15 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0015Normal | 1.3.6.1.4.1.33.0.20015 | Generated when alarm point 15 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0016Alarm | 1.3.6.1.4.1.33.0.10016 | Generated when alarm point 16 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0016Normal | 1.3.6.1.4.1.33.0.20016 | Generated when alarm point 16 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0017Alarm | 1.3.6.1.4.1.33.0.10017 | Generated when alarm point 17 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0017Normal | 1.3.6.1.4.1.33.0.20017 | Generated when alarm point 17 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0018Alarm | 1.3.6.1.4.1.33.0.10018 | Generated when alarm point 18 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0018Normal | 1.3.6.1.4.1.33.0.20018 | Generated when alarm point 18 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0019Alarm | 1.3.6.1.4.1.33.0.10019 | Generated when alarm point 19 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0019Normal | 1.3.6.1.4.1.33.0.20019 | Generated when alarm point 19 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0020Alarm | 1.3.6.1.4.1.33.0.10020 | Generated when alarm point 20 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0020Normal | 1.3.6.1.4.1.33.0.20020 | Generated when alarm point 20 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0021Alarm | 1.3.6.1.4.1.33.0.10021 | Generated when alarm point 21 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0021Normal | 1.3.6.1.4.1.33.0.20021 | Generated when alarm point 21 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0022Alarm | 1.3.6.1.4.1.33.0.10022 | Generated when alarm point 22 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0022Normal | 1.3.6.1.4.1.33.0.20022 | Generated when alarm point 22 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0023Alarm | 1.3.6.1.4.1.33.0.10023 | Generated when alarm point 23 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0023Normal | 1.3.6.1.4.1.33.0.20023 | Generated when alarm point 23 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0024Alarm | 1.3.6.1.4.1.33.0.10024 | Generated when alarm point 24 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0024Normal | 1.3.6.1.4.1.33.0.20024 | Generated when alarm point 24 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0025Alarm | 1.3.6.1.4.1.33.0.10025 | Generated when alarm point 25 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0025Normal | 1.3.6.1.4.1.33.0.20025 | Generated when alarm point 25 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0026Alarm | 1.3.6.1.4.1.33.0.10026 | Generated when alarm point 26 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0026Normal | 1.3.6.1.4.1.33.0.20026 | Generated when alarm point 26 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0027Alarm | 1.3.6.1.4.1.33.0.10027 | Generated when alarm point 27 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0027Normal | 1.3.6.1.4.1.33.0.20027 | Generated when alarm point 27 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0028Alarm | 1.3.6.1.4.1.33.0.10028 | Generated when alarm point 28 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0028Normal | 1.3.6.1.4.1.33.0.20028 | Generated when alarm point 28 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0029Alarm | 1.3.6.1.4.1.33.0.10029 | Generated when alarm point 29 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0029Normal | 1.3.6.1.4.1.33.0.20029 | Generated when alarm point 29 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0030Alarm | 1.3.6.1.4.1.33.0.10030 | Generated when alarm point 30 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0030Normal | 1.3.6.1.4.1.33.0.20030 | Generated when alarm point 30 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0031Alarm | 1.3.6.1.4.1.33.0.10031 | Generated when alarm point 31 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0031Normal | 1.3.6.1.4.1.33.0.20031 | Generated when alarm point 31 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0032Alarm | 1.3.6.1.4.1.33.0.10032 | Generated when alarm point 32 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0032Normal | 1.3.6.1.4.1.33.0.20032 | Generated when alarm point 32 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0033Alarm | 1.3.6.1.4.1.33.0.10033 | Generated when alarm point 33 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0033Normal | 1.3.6.1.4.1.33.0.20033 | Generated when alarm point 33 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0034Alarm | 1.3.6.1.4.1.33.0.10034 | Generated when alarm point 34 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0034Normal | 1.3.6.1.4.1.33.0.20034 | Generated when alarm point 34 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0035Alarm | 1.3.6.1.4.1.33.0.10035 | Generated when alarm point 35 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0035Normal | 1.3.6.1.4.1.33.0.20035 | Generated when alarm point 35 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0036Alarm | 1.3.6.1.4.1.33.0.10036 | Generated when alarm point 36 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0036Normal | 1.3.6.1.4.1.33.0.20036 | Generated when alarm point 36 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0037Alarm | 1.3.6.1.4.1.33.0.10037 | Generated when alarm point 37 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0037Normal | 1.3.6.1.4.1.33.0.20037 | Generated when alarm point 37 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0038Alarm | 1.3.6.1.4.1.33.0.10038 | Generated when alarm point 38 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0038Normal | 1.3.6.1.4.1.33.0.20038 | Generated when alarm point 38 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0039Alarm | 1.3.6.1.4.1.33.0.10039 | Generated when alarm point 39 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0039Normal | 1.3.6.1.4.1.33.0.20039 | Generated when alarm point 39 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0040Alarm | 1.3.6.1.4.1.33.0.10040 | Generated when alarm point 40 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0040Normal | 1.3.6.1.4.1.33.0.20040 | Generated when alarm point 40 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0041Alarm | 1.3.6.1.4.1.33.0.10041 | Generated when alarm point 41 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0041Normal | 1.3.6.1.4.1.33.0.20041 | Generated when alarm point 41 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0042Alarm | 1.3.6.1.4.1.33.0.10042 | Generated when alarm point 42 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0042Normal | 1.3.6.1.4.1.33.0.20042 | Generated when alarm point 42 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0043Alarm | 1.3.6.1.4.1.33.0.10043 | Generated when alarm point 43 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0043Normal | 1.3.6.1.4.1.33.0.20043 | Generated when alarm point 43 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0044Alarm | 1.3.6.1.4.1.33.0.10044 | Generated when alarm point 44 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0044Normal | 1.3.6.1.4.1.33.0.20044 | Generated when alarm point 44 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0045Alarm | 1.3.6.1.4.1.33.0.10045 | Generated when alarm point 45 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0045Normal | 1.3.6.1.4.1.33.0.20045 | Generated when alarm point 45 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0046Alarm | 1.3.6.1.4.1.33.0.10046 | Generated when alarm point 46 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0046Normal | 1.3.6.1.4.1.33.0.20046 | Generated when alarm point 46 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0047Alarm | 1.3.6.1.4.1.33.0.10047 | Generated when alarm point 47 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0047Normal | 1.3.6.1.4.1.33.0.20047 | Generated when alarm point 47 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0048Alarm | 1.3.6.1.4.1.33.0.10048 | Generated when alarm point 48 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0048Normal | 1.3.6.1.4.1.33.0.20048 | Generated when alarm point 48 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0049Alarm | 1.3.6.1.4.1.33.0.10049 | Generated when alarm point 49 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0049Normal | 1.3.6.1.4.1.33.0.20049 | Generated when alarm point 49 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0050Alarm | 1.3.6.1.4.1.33.0.10050 | Generated when alarm point 50 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0050Normal | 1.3.6.1.4.1.33.0.20050 | Generated when alarm point 50 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0051Alarm | 1.3.6.1.4.1.33.0.10051 | Generated when alarm point 51 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0051Normal | 1.3.6.1.4.1.33.0.20051 | Generated when alarm point 51 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0052Alarm | 1.3.6.1.4.1.33.0.10052 | Generated when alarm point 52 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0052Normal | 1.3.6.1.4.1.33.0.20052 | Generated when alarm point 52 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0053Alarm | 1.3.6.1.4.1.33.0.10053 | Generated when alarm point 53 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0053Normal | 1.3.6.1.4.1.33.0.20053 | Generated when alarm point 53 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0054Alarm | 1.3.6.1.4.1.33.0.10054 | Generated when alarm point 54 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0054Normal | 1.3.6.1.4.1.33.0.20054 | Generated when alarm point 54 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0055Alarm | 1.3.6.1.4.1.33.0.10055 | Generated when alarm point 55 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0055Normal | 1.3.6.1.4.1.33.0.20055 | Generated when alarm point 55 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0056Alarm | 1.3.6.1.4.1.33.0.10056 | Generated when alarm point 56 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0056Normal | 1.3.6.1.4.1.33.0.20056 | Generated when alarm point 56 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0057Alarm | 1.3.6.1.4.1.33.0.10057 | Generated when alarm point 57 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0057Normal | 1.3.6.1.4.1.33.0.20057 | Generated when alarm point 57 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0058Alarm | 1.3.6.1.4.1.33.0.10058 | Generated when alarm point 58 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0058Normal | 1.3.6.1.4.1.33.0.20058 | Generated when alarm point 58 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0059Alarm | 1.3.6.1.4.1.33.0.10059 | Generated when alarm point 59 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0059Normal | 1.3.6.1.4.1.33.0.20059 | Generated when alarm point 59 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0060Alarm | 1.3.6.1.4.1.33.0.10060 | Generated when alarm point 60 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0060Normal | 1.3.6.1.4.1.33.0.20060 | Generated when alarm point 60 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0061Alarm | 1.3.6.1.4.1.33.0.10061 | Generated when alarm point 61 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0061Normal | 1.3.6.1.4.1.33.0.20061 | Generated when alarm point 61 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0062Alarm | 1.3.6.1.4.1.33.0.10062 | Generated when alarm point 62 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0062Normal | 1.3.6.1.4.1.33.0.20062 | Generated when alarm point 62 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0063Alarm | 1.3.6.1.4.1.33.0.10063 | Generated when alarm point 63 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0063Normal | 1.3.6.1.4.1.33.0.20063 | Generated when alarm point 63 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0064Alarm | 1.3.6.1.4.1.33.0.10064 | Generated when alarm point 64 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0064Normal | 1.3.6.1.4.1.33.0.20064 | Generated when alarm point 64 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0065Alarm | 1.3.6.1.4.1.33.0.10065 | Generated when alarm point 65 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0065Normal | 1.3.6.1.4.1.33.0.20065 | Generated when alarm point 65 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0066Alarm | 1.3.6.1.4.1.33.0.10066 | Generated when alarm point 66 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0066Normal | 1.3.6.1.4.1.33.0.20066 | Generated when alarm point 66 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0067Alarm | 1.3.6.1.4.1.33.0.10067 | Generated when alarm point 67 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0067Normal | 1.3.6.1.4.1.33.0.20067 | Generated when alarm point 67 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0068Alarm | 1.3.6.1.4.1.33.0.10068 | Generated when alarm point 68 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0068Normal | 1.3.6.1.4.1.33.0.20068 | Generated when alarm point 68 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0069Alarm | 1.3.6.1.4.1.33.0.10069 | Generated when alarm point 69 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0069Normal | 1.3.6.1.4.1.33.0.20069 | Generated when alarm point 69 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0070Alarm | 1.3.6.1.4.1.33.0.10070 | Generated when alarm point 70 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0070Normal | 1.3.6.1.4.1.33.0.20070 | Generated when alarm point 70 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0071Alarm | 1.3.6.1.4.1.33.0.10071 | Generated when alarm point 71 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0071Normal | 1.3.6.1.4.1.33.0.20071 | Generated when alarm point 71 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0072Alarm | 1.3.6.1.4.1.33.0.10072 | Generated when alarm point 72 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0072Normal | 1.3.6.1.4.1.33.0.20072 | Generated when alarm point 72 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0073Alarm | 1.3.6.1.4.1.33.0.10073 | Generated when alarm point 73 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0073Normal | 1.3.6.1.4.1.33.0.20073 | Generated when alarm point 73 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0074Alarm | 1.3.6.1.4.1.33.0.10074 | Generated when alarm point 74 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0074Normal | 1.3.6.1.4.1.33.0.20074 | Generated when alarm point 74 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0075Alarm | 1.3.6.1.4.1.33.0.10075 | Generated when alarm point 75 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0075Normal | 1.3.6.1.4.1.33.0.20075 | Generated when alarm point 75 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0076Alarm | 1.3.6.1.4.1.33.0.10076 | Generated when alarm point 76 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0076Normal | 1.3.6.1.4.1.33.0.20076 | Generated when alarm point 76 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0077Alarm | 1.3.6.1.4.1.33.0.10077 | Generated when alarm point 77 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0077Normal | 1.3.6.1.4.1.33.0.20077 | Generated when alarm point 77 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0078Alarm | 1.3.6.1.4.1.33.0.10078 | Generated when alarm point 78 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0078Normal | 1.3.6.1.4.1.33.0.20078 | Generated when alarm point 78 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0079Alarm | 1.3.6.1.4.1.33.0.10079 | Generated when alarm point 79 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0079Normal | 1.3.6.1.4.1.33.0.20079 | Generated when alarm point 79 from a low density unit transitions to the normal state. | ||
| NTF alarmInputLowDensity0080Alarm | 1.3.6.1.4.1.33.0.10080 | Generated when alarm point 80 from a low density unit transitions to the alarm state. | ||
| NTF alarmInputLowDensity0080Normal | 1.3.6.1.4.1.33.0.20080 | Generated when alarm point 80 from a low density unit transitions to the normal state. | ||
| NTF alarmMasterInputStateChange | 1.3.6.1.4.1.33.0.41 | Indication that the alarm input point within a high density alarm management port transitioned to open or closed. | ||
| NTF alarmMasterNotResponding | 1.3.6.1.4.1.33.0.39 | Indication that the high density alarm management device lost or regained contact with the inReach port to which it was connected as indicated by the basicPortAlarmMasterStatus variable. | ||
| NTF alarmMasterSideAOff | 1.3.6.1.4.1.33.0.46 | Indication that side A powered off in the attached IR7104 alarm unit due to DC rail fluctuations. | ||
| NTF alarmMasterSideAOn | 1.3.6.1.4.1.33.0.48 | Indication that side A powered on in the attached IR7104 alarm unit after previous power off. | ||
| NTF alarmMasterSideBOff | 1.3.6.1.4.1.33.0.47 | Indication that side B powered off in the attached IR7104 alarm unit due to DC rail fluctuations. | ||
| NTF alarmMasterSideBOn | 1.3.6.1.4.1.33.0.49 | Indication that side B powered on in the attached IR7104 alarm unit after previous power off. | ||
| NTF asciiToTrapTranslation | 1.3.6.1.4.1.33.0.42 | This trap contains ASCII data, which arrived at serial port, was formatted as a trap, and sent out on the network. | ||
| GAU basicActivePorts | 1.3.6.1.4.1.33.13.1.10 | Gauge | read-only | The number of ports with connected sessions or logged in users. Corresponds directly to the value labeled 'Active Ports:' and 'Cur' in the SERVER STATUS display. |
| GAU basicActivePortsHigh | 1.3.6.1.4.1.33.13.1.11 | Gauge | read-only | The highest value of basicActivePorts since system initialization. Corresponds directly to the value labeled 'Active Ports:' and 'High' in the SERVER STATUS display. |
| GAU basicActiveUsers | 1.3.6.1.4.1.33.13.1.12 | Gauge | read-only | The number of logged in users. Corresponds directly to the value labeled 'Active Users:' and 'Cur' in the SERVER STATUS display. |
| GAU basicActiveUsersHigh | 1.3.6.1.4.1.33.13.1.13 | Gauge | read-only | The highest value of basicActiveUsers since system initialization. Corresponds directly to the value labeled 'Active Users:' and 'High' in the SERVER STATUS display. |
| INT basicAlarmMasterControlOutputSignal | 1.3.6.1.4.1.33.13.1.36.1.6 | INTEGER | read-write | Control to toggle the output signal for an alarm point. |
| INT basicAlarmMasterDisplay | 1.3.6.1.4.1.33.13.1.36.1.13 | INTEGER | read-write | Control to toggle the display of the alarm status for this point in the display window of the high density alarm unit. |
| INT basicAlarmMasterInputDebounceInterval | 1.3.6.1.4.1.33.13.1.36.1.8 | INTEGER | read-write | Amount of time in seconds to debounce a signal change before triggering an alarm. |
| INT basicAlarmMasterInputEnable | 1.3.6.1.4.1.33.13.1.36.1.7 | INTEGER | read-write | Control to toggle whether this alarm point is active. |
| basicAlarmMasterInputEntry | 1.3.6.1.4.1.33.13.1.36.1 | not-accessible | An entry in the basicAlarmMasterInputTable. | |
| INT basicAlarmMasterInputFaultSeverity | 1.3.6.1.4.1.33.13.1.36.1.9 | INTEGER | read-write | Control to determine the severity level associated with the trap sent out when a fault occurs for this alarm input point. |
| INT basicAlarmMasterInputFaultState | 1.3.6.1.4.1.33.13.1.36.1.10 | INTEGER | read-write | Control to indicate which state, open or closed, represents the fault condition for this alarm input point. The other state is the cleared condition. |
| STR basicAlarmMasterInputManufacturer | 1.3.6.1.4.1.33.13.1.36.1.17 | DisplayString | read-write | The name used to identify the manufacturer of this equipment. |
| STR basicAlarmMasterInputModel | 1.3.6.1.4.1.33.13.1.36.1.18 | DisplayString | read-write | The model name of this equipment. |
| STR basicAlarmMasterInputName | 1.3.6.1.4.1.33.13.1.36.1.4 | DisplayString | read-write | The name used to identify this alarm point. |
| INT basicAlarmMasterInputPoint | 1.3.6.1.4.1.33.13.1.36.1.3 | INTEGER | read-only | An index value that uniquely identifies an alarm point within an alarm slot on a high density alarm port. |
| INT basicAlarmMasterInputPort | 1.3.6.1.4.1.33.13.1.36.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| STR basicAlarmMasterInputRelatedEquipment | 1.3.6.1.4.1.33.13.1.36.1.15 | DisplayString | read-write | The name used to identify related equipment. |
| STR basicAlarmMasterInputSiteId | 1.3.6.1.4.1.33.13.1.36.1.16 | DisplayString | read-write | The name used to identify the site where the unit resides. |
| INT basicAlarmMasterInputSlot | 1.3.6.1.4.1.33.13.1.36.1.2 | INTEGER | read-only | An index value that uniquely identifies a slot of alarm points on a given high density alarm port. |
| INT basicAlarmMasterInputStatus | 1.3.6.1.4.1.33.13.1.36.1.11 | INTEGER | read-only | Indicates the current status of the alarm input point. If the basicAlarmMasterInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared. |
| basicAlarmMasterInputTable | 1.3.6.1.4.1.33.13.1.36 | not-accessible | Information about the high density alarm manager's alarm inputs. | |
| INT basicAlarmMasterInputTrapEnable | 1.3.6.1.4.1.33.13.1.36.1.5 | INTEGER | read-write | Control to send a trap when the alarm input changes state. |
| INT basicAlarmMasterInputValue | 1.3.6.1.4.1.33.13.1.36.1.12 | INTEGER | read-only | Indicates the current state of the alarm input point. |
| STR basicAlarmMasterInputZone | 1.3.6.1.4.1.33.13.1.36.1.14 | DisplayString | read-write | The name used to identify the zone where the equipment resides. |
| STR basicAutoProtocolDetectMessage | 1.3.6.1.4.1.33.13.1.100 | DisplayString | read-write | The text string sent as a prompt message out the port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Message' in the SERVER UNIT display. |
| INT basicBroadcast | 1.3.6.1.4.1.33.13.1.1 | INTEGER | read-write | Control for user ability to broadcast messages to other local ports. Corresponds directly to SERVER BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT basicConsoleLogoutDisconnect | 1.3.6.1.4.1.33.13.1.19 | INTEGER | read-write | Control for automatic session disconnection when a console port user logs out. Corresponds directly to SERVER CONSOLE LOGOUT and the presence of the label 'Console Logout' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| basicContactClosureOrAlarmInputEntry | 1.3.6.1.4.1.33.13.1.25.1 | not-accessible | An entry in the basicContactClosureOrAlarmInputTable. | |
| INT basicContactClosureOrAlarmInputFaultSeverity | 1.3.6.1.4.1.33.13.1.25.1.4 | INTEGER | read-write | Control to determine the severity level associated with the trap sent out when a fault occurs for a given contact closure or alarm input. |
| INT basicContactClosureOrAlarmInputFaultState | 1.3.6.1.4.1.33.13.1.25.1.5 | INTEGER | read-write | Control to indicate which state, open or closed, represents the fault condition. The other state is the cleared condition. |
| INT basicContactClosureOrAlarmInputIndex | 1.3.6.1.4.1.33.13.1.25.1.10 | INTEGER | read-only | An index which uniquely identifies the contact closure or alarm input. |
| STR basicContactClosureOrAlarmInputManufacturer | 1.3.6.1.4.1.33.13.1.25.1.11 | DisplayString | read-write | The name used to identify the manufacturer of this equipment. |
| STR basicContactClosureOrAlarmInputModel | 1.3.6.1.4.1.33.13.1.25.1.12 | DisplayString | read-write | The model name of this equipment. |
| STR basicContactClosureOrAlarmInputName | 1.3.6.1.4.1.33.13.1.25.1.2 | DisplayString | read-write | The name used to identify this contact closure or alarm input. |
| STR basicContactClosureOrAlarmInputRelatedEquipment | 1.3.6.1.4.1.33.13.1.25.1.8 | DisplayString | read-write | The name used to identify related equipment. |
| STR basicContactClosureOrAlarmInputSiteId | 1.3.6.1.4.1.33.13.1.25.1.9 | DisplayString | read-write | The name used to identify the site where the unit resides. |
| INT basicContactClosureOrAlarmInputStatus | 1.3.6.1.4.1.33.13.1.25.1.6 | INTEGER | read-only | Indicates the current status of the contact closure or alarm input. If the basicContactClosureOrAlarmInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared. |
| basicContactClosureOrAlarmInputTable | 1.3.6.1.4.1.33.13.1.25 | not-accessible | Information about contact closures or alarm inputs. | |
| INT basicContactClosureOrAlarmInputTrapEnable | 1.3.6.1.4.1.33.13.1.25.1.3 | INTEGER | read-write | Control to send trap when contact closure or alarm input changes state. |
| INT basicContactClosureOrAlarmInputValue | 1.3.6.1.4.1.33.13.1.25.1.1 | INTEGER | read-only | Indicates the state of the contact closure or alarm input. |
| STR basicContactClosureOrAlarmInputZone | 1.3.6.1.4.1.33.13.1.25.1.7 | DisplayString | read-write | The name used to identify the zone where the equipment resides. |
| INT basicControlledPorts | 1.3.6.1.4.1.33.13.1.20 | INTEGER | read-write | Status of Controlled Ports feature. Corresponds directly to the 'Controlled Ports' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. Enabling this feature causes strings of control characters to be sent out on a port upon starting and/or stopping a session |
| basicControlOutputEntry | 1.3.6.1.4.1.33.13.1.30.1 | not-accessible | An entry in the basicControlOutputTable. | |
| INT basicControlOutputIndex | 1.3.6.1.4.1.33.13.1.30.1.10 | INTEGER | read-only | An index which uniquely identifies a distribution control signal point. |
| STR basicControlOutputName | 1.3.6.1.4.1.33.13.1.30.1.2 | DisplayString | read-write | The name used to identify this distribution control signal point. |
| basicControlOutputRelayEntry | 1.3.6.1.4.1.33.13.1.38.1 | not-accessible | An entry in the basicControlOutputRelayTable. | |
| INT basicControlOutputRelayIndex | 1.3.6.1.4.1.33.13.1.38.1.1 | INTEGER | read-only | An index which uniquely identifies a control output relay. |
| STR basicControlOutputRelayName | 1.3.6.1.4.1.33.13.1.38.1.2 | DisplayString | read-write | The name used to identify this control output relay. |
| INT basicControlOutputRelayState | 1.3.6.1.4.1.33.13.1.38.1.3 | INTEGER | read-write | Controls the opening or closing of the control output relay. |
| INT basicControlOutputRelayStatus | 1.3.6.1.4.1.33.13.1.38.1.4 | INTEGER | read-only | Indicates the current status of the control output relay. |
| basicControlOutputRelayTable | 1.3.6.1.4.1.33.13.1.38 | not-accessible | Information about controlled output relays. | |
| INT basicControlOutputSignalDtrRts | 1.3.6.1.4.1.33.13.1.30.1.1 | INTEGER | read-write | Controls the raising or lowering of a signal on a distribution control signal point. The signal is DTR when the basicControlOutputIndex is odd, or RTS when the basicControlOutputIndex is even. |
| basicControlOutputTable | 1.3.6.1.4.1.33.13.1.30 | not-accessible | Information about controlled output distribution points. | |
| basicControlSignalEntry | 1.3.6.1.4.1.33.13.1.28.1 | not-accessible | An entry in the basicControlSignalTable. | |
| INT basicControlSignalIndex | 1.3.6.1.4.1.33.13.1.28.1.10 | INTEGER | read-only | An index which uniquely identifies a control signal point. |
| basicControlSignalTable | 1.3.6.1.4.1.33.13.1.28 | not-accessible | Information about Environmental Manager Control Signal points. | |
| INT basicControlSignalValue | 1.3.6.1.4.1.33.13.1.28.1.1 | INTEGER | read-write | Sets and reads the state of the control signal point. |
| INT basicEnvironmentalManagerCircuitBreaker | 1.3.6.1.4.1.33.13.1.24 | INTEGER | read-only | Indicates whether the circuit breaker is activated. |
| INT basicErrorReport | 1.3.6.1.4.1.33.13.1.2 | INTEGER | read-write | Control for server display of an error when the user gives an unsupported command. Corresponds directly to SERVER REPORT ERRORS and the presence of the label 'Report Errors' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT basicHumidityAlarmSeverity | 1.3.6.1.4.1.33.13.1.27.2.1.5 | INTEGER | read-write | Control to indicate the severity level associated with the trap sent out when the humidity reading is out-of-bounds. |
| INT basicHumidityAlarmStatus | 1.3.6.1.4.1.33.13.1.27.2.1.6 | INTEGER | read-only | Indicates the current status of the humidity sensor. If the basicHumidityValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level. |
| INT basicHumiditySensor | 1.3.6.1.4.1.33.13.1.27.2.1.3 | INTEGER | read-write | Controls the enabling or disabling of a humidity sensor. |
| basicHumiditySensorEntry | 1.3.6.1.4.1.33.13.1.27.2.1 | not-accessible | An entry in the basicHumiditySensorTable. | |
| INT basicHumiditySensorIndex | 1.3.6.1.4.1.33.13.1.27.2.1.10 | INTEGER | read-only | An index which uniquely identifies a humidity sensor. |
| basicHumiditySensorTable | 1.3.6.1.4.1.33.13.1.27.2 | not-accessible | Information about Environmental Manager Humidity Sensors. | |
| INT basicHumidityTrapHighThreshold | 1.3.6.1.4.1.33.13.1.27.2.1.1 | INTEGER | read-write | The humidity at or above which a sensorThresholdTrap is generated. |
| INT basicHumidityTrapLowThreshold | 1.3.6.1.4.1.33.13.1.27.2.1.2 | INTEGER | read-write | The humidity at or below which a sensorThresholdTrap is generated. |
| INT basicHumidityValue | 1.3.6.1.4.1.33.13.1.27.2.1.4 | INTEGER | read-write | The current humidity reading for this sensor. |
| INT basicInactivityTimer | 1.3.6.1.4.1.33.13.1.4 | INTEGER | read-write | Number of minutes a terminal may remain logged in with no sessions, no input or output, and no modem transitions. Corresponds directly to SERVER INACTIVITY TIMER and the value labeled 'Inactivity Timer:' in the SERVER CHARACTERISTICS display. |
| INT basicLock | 1.3.6.1.4.1.33.13.1.3 | INTEGER | read-write | Control for user ability to use a password to protect a logged in terminal from other users. Corresponds directly to SERVER LOCK and the presence of the label 'Lock' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| STR basicLoginPassword | 1.3.6.1.4.1.33.13.1.7 | DisplayString | read-write | The password a user must enter to be given the opportunity to log in. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER LOGIN PASSWORD. |
| STR basicLoginPrompt | 1.3.6.1.4.1.33.13.1.8 | DisplayString | read-write | The text string the server displays to prompt a user for the login password. Corresponds directly to SERVER LOGIN PROMPT. |
| INT basicPasswordRetryLimit | 1.3.6.1.4.1.33.13.1.5 | INTEGER | read-write | Number of times the server allows a user to retry an incorrect password. Corresponds directly to SERVER PASSWORD LIMIT and the value labeled 'Password Limit:' in the SERVER CHARACTERISTICS display. |
| STR basicPortActiveUserName | 1.3.6.1.4.1.33.13.1.17.1.26 | DisplayString | read-only | The user name currently logged into the port. Corresponds directly to the value by the port number and labeled 'Username' in the USERS display. |
| INT basicPortAlarmControl | 1.3.6.1.4.1.33.13.1.17.1.49 | INTEGER | read-write | Control to configure this port for alarm input and control output. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortSensor. A set will only update the permanent database. Use a charPortReset for this change to take effect. |
| INT basicPortAlarmMaster | 1.3.6.1.4.1.33.13.1.17.1.61 | INTEGER | read-write | Control to configure this port for high densitiy alarm input and control output management. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort, basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect. |
| INT basicPortAlarmMasterAccounting | 1.3.6.1.4.1.33.13.1.17.1.62 | INTEGER | read-write | Control to toggle logging of alarm events on this port. Use a charPortReset for this change to take effect. |
| INT basicPortAlarmMasterAudibleAlarm | 1.3.6.1.4.1.33.13.1.17.1.63 | INTEGER | read-write | Control whether the alarm will have an audible sound for all alarm points attached to this port. |
| INT basicPortAlarmMasterFaultSeverity | 1.3.6.1.4.1.33.13.1.17.1.71 | INTEGER | read-write | Control to determine the severity level associated with the trap sent out when a fault occurs when no response is obtained from the high density alarm unit attached to this port. |
| INT basicPortAlarmMasterFixTime | 1.3.6.1.4.1.33.13.1.17.1.64 | INTEGER | read-write | Time in minutes between audible alarm soundings for an alarm master port. This occurs after someone hits the master alarm reset button. If there is at least one alarm condition on an alarm point within the fix time, then the alarm will sound again at the end of that fix time. |
| STR basicPortAlarmMasterLcdDisplayString | 1.3.6.1.4.1.33.13.1.17.1.65 | DisplayString | read-write | Updates the LCD display message for the high density alarm unit attached to the port. Corresponds directly to the DISPLAY AMST command. |
| INT basicPortAlarmMasterReboot | 1.3.6.1.4.1.33.13.1.17.1.66 | INTEGER | read-write | Control to reboot the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Corresponds directly to the REBOOT AMST command. |
| INT basicPortAlarmMasterStatus | 1.3.6.1.4.1.33.13.1.17.1.70 | INTEGER | read-only | Indicates the current status of the high density alarm unit attached to the port. If no response is obtained from this unit, the status is set to basicPortAlarmMasterFaultSeverity. Otherwise it is cleared. |
| INT basicPortAlarmMasterUpdateFirmware | 1.3.6.1.4.1.33.13.1.17.1.69 | INTEGER | read-write | Control to update firmware for the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. The basicPortAlarmMasterUpdateFirmwareHost and basicPortAlarmMasterUpdateFirmwareFileName must be set prior to setting this object. Corresponds directly to the UPDATE AMST FIRMWARE command. |
| STR basicPortAlarmMasterUpdateFirmwareFileName | 1.3.6.1.4.1.33.13.1.17.1.68 | DisplayString | read-write | The filename to request when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's FILE parameter. |
| IP basicPortAlarmMasterUpdateFirmwareHost | 1.3.6.1.4.1.33.13.1.17.1.67 | IpAddress | read-write | The internet address of the server to use when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's INTERNET ADDRESS parameter. |
| INT basicPortAsciiToTrapTranslation | 1.3.6.1.4.1.33.13.1.17.1.79 | INTEGER | read-write | Control to configure the port as an ascii-to-trap translator. One must log out the port for this change to take effect. |
| STR basicPortAsciiToTrapTranslationLastMessage | 1.3.6.1.4.1.33.13.1.17.1.82 | DisplayString | read-only | The last message or partial message sent out by this port. |
| CTR basicPortAsciiToTrapTranslationMessages | 1.3.6.1.4.1.33.13.1.17.1.81 | Counter | read-only | Count of number of trap messages sent from this port. |
| INT basicPortAsciiToTrapTranslationTrapSeverity | 1.3.6.1.4.1.33.13.1.17.1.80 | INTEGER | read-write | Control to determine the severity level associated with the trap sent out from this port. One must log out the port for this change to take effect. |
| INT basicPortAutoConnect | 1.3.6.1.4.1.33.13.1.17.1.7 | INTEGER | read-write | Control for automatic session connection. Corresponds directly to PORT AUTOCONNECT and the presence of the label 'Autoconnect' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortAutoLogin | 1.3.6.1.4.1.33.13.1.17.1.8 | INTEGER | read-write | Control for automatic port login. Corresponds directly to PORT AUTODEDICATED and the presence of the label 'Autodedicated' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| OCT basicPortBreakSequence | 1.3.6.1.4.1.33.13.1.17.1.51 | OCTET STRING | read-write | A sequence of characters to be sent out the serial port on receipt of a Break from the network in lieu of a hardware break. The sequence entered by the user is converted into an octet string up to four bytes long to be sent out the serial port. For example, the user's representation of octal 2, or '\002', takes four characters in basicPortBreakSequence; but only one byte in the string sent out the serial port. |
| INT basicPortBroadcast | 1.3.6.1.4.1.33.13.1.17.1.9 | INTEGER | read-write | Control for display of messages sent by users on other ports. Corresponds directly to PORT BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortBuffering | 1.3.6.1.4.1.33.13.1.17.1.85 | INTEGER | read-write | Control to allow data from an attached device to be retained across multiple sessions. When a session is established to a port with buffering, the contents of the command buffer is sent to the remote device. One must log out the port for this change to take effect. |
| INT basicPortCommandLogging | 1.3.6.1.4.1.33.13.1.17.1.50 | INTEGER | read-write | A control to toggle logging of commands at this port. Command input may be logged from direct terminal connections, session input from the LAN, or session output to the LAN. Corresponds directly to the presence of 'Command Logging' under the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off. |
| INT basicPortCommandLoggingSuppressControlCharacters | 1.3.6.1.4.1.33.13.1.17.1.56 | INTEGER | read-write | Control to toggle suppression of control characters in the command log. This object can only be set to enabled when command logging is enabled on that port. |
| INT basicPortConnectResume | 1.3.6.1.4.1.33.13.1.17.1.10 | INTEGER | read-write | Control for behavior of a connection attempt to a destination where the port already has a connection. 'disabled' causes a new connection. 'enabled' causes the existing connection to become the active connection. Corresponds directly to PORT CONNECTRESUME and the presence of the label 'Connectresume' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortConsolePort | 1.3.6.1.4.1.33.13.1.17.1.46 | INTEGER | read-write | Control to configure this port as a console port. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect. |
| OCT basicPortControlledPortLogin | 1.3.6.1.4.1.33.13.1.17.1.34 | OCTET STRING | read-write | A control string to send out the serial port upon port login. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Login:' in the PORT CONTROLLED display. |
| OCT basicPortControlledPortLogout | 1.3.6.1.4.1.33.13.1.17.1.35 | OCTET STRING | read-write | A control string to send out the serial port upon port logout. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Logout:' in the PORT CONTROLLED display. |
| OCT basicPortControlledSessionInitialize | 1.3.6.1.4.1.33.13.1.17.1.36 | OCTET STRING | read-write | A control string to send out the serial port upon entering a session. Corresponds to the hexadecimal code which represented in ASCII following the label 'Controlled Session Initialize:' in the PORT CONTROLLED display. |
| OCT basicPortControlledSessionTerminate | 1.3.6.1.4.1.33.13.1.17.1.37 | OCTET STRING | read-write | A control string to send out the serial port upon exiting a session. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Session Terminate:' in the PORT CONTROLLED display. |
| INT basicPortDataLogging | 1.3.6.1.4.1.33.13.1.17.1.57 | INTEGER | read-write | Control to toggle data logging on the specified port. |
| INT basicPortDataLoggingSuppressControlCharacters | 1.3.6.1.4.1.33.13.1.17.1.58 | INTEGER | read-write | Control to toggle suppression of control characters in the data log. This object can only be set to enabled when data logging is enabled on that port. |
| INT basicPortDefaultDedicatedSessionType | 1.3.6.1.4.1.33.13.1.17.1.42 | INTEGER | read-write | This integer is interpreted as a bit mask that specifies the default session type for a dedicated service for this port. The bit numbers are: 1;service name, 2;node name, 3;port name, 4, telnet console; 5, rlogin; 6, bridge console; 7, chassis console. |
| INT basicPortDefaultDestAction | 1.3.6.1.4.1.33.13.1.17.1.2 | INTEGER | read-write | The action to take relative to basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. |
| INT basicPortDefaultDestControlled | 1.3.6.1.4.1.33.13.1.17.1.33 | INTEGER | read-write | A control to send preconfigured controlled port session strings when entering or exiting a session established to the basicPortDefaultDestName. Corresponds directly to the value labeled '(Controlled)' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. |
| STR basicPortDefaultDestLATNodeName | 1.3.6.1.4.1.33.13.1.17.1.5 | DisplayString | read-write | A LAT node name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. This object can have a non- zero-length value only if the value of basicPortDefaultDestProtocol is 'lat'. |
| STR basicPortDefaultDestLATPortName | 1.3.6.1.4.1.33.13.1.17.1.6 | DisplayString | read-write | A LAT port name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. this object can hav a non-zero-length value only if the value if basicPortDefaultDestProtocol is 'lat' |
| STR basicPortDefaultDestName | 1.3.6.1.4.1.33.13.1.17.1.4 | DisplayString | read-write | The default name to use in forming a connection when no other name is specified. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the value labeled 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. If the value of basicPortDefaultDestProtocol is 'telnet', an Internet port number may be included on the end of the name, delimited with a colon (':'). If the value of basicPortDefaultDestProtocol is not 'telnet', then the maximum length is 16. |
| INT basicPortDefaultDestProtocol | 1.3.6.1.4.1.33.13.1.17.1.3 | INTEGER | read-write | The session protocol to use with basicPortDefaultDestName. Corresponds directly to LAT/TELNET PORT DEDICATED/PREFERRED SERVICE. |
| INT basicPortDefaultProtocol | 1.3.6.1.4.1.33.13.1.17.1.19 | INTEGER | read-write | The session protocol to use when not otherwise specified. Corresponds directly to PORT RESOLVE SERVICE and the value labeled 'Resolve Service:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicPortDefaultSessionMode | 1.3.6.1.4.1.33.13.1.17.1.27 | INTEGER | read-write | Data recognition mode when starting a session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data Corresponds directly to PORT DEFAULT SESSION MODE and the value labeled 'Default Session Mode:' in the PORT ALTERNATE CHARACTERISTICS display. |
| STR basicPortDefaultUserName | 1.3.6.1.4.1.33.13.1.17.1.17 | DisplayString | read-write | Default user name to use for automatically logging in the port. Corresponds directly to PORT USERNAME and the value labeled 'Port n:' in the PORT CHARACTERISTICS display. |
| INT basicPortDialup | 1.3.6.1.4.1.33.13.1.17.1.11 | INTEGER | read-write | Defines whether the port should be considered as connected to a dialup line. 'enabled' means that it is. Corresponds directly to PORT DIALUP and the presence of the label 'Dial Up' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| basicPortEntry | 1.3.6.1.4.1.33.13.1.17.1 | not-accessible | Basic parameter values for a port. | |
| INT basicPortFallBack | 1.3.6.1.4.1.33.13.1.17.1.60 | INTEGER | read-write | Control to allow a 'fallback' authentication mechanism after RADIUS or SecurID authentication fails because the RADIUS or SecurID servers are unavailable. Onboard security, an internal security database, is used for fallback authentication. The user in fallback mode must enter a valid username and password to be successfully logged in. The change takes effect after logging out the port. |
| INT basicPortFallThrough | 1.3.6.1.4.1.33.13.1.17.1.55 | INTEGER | read-write | Control to allow a user to login to a port after RADIUS or SecurID authentication fails because the RADIUS servers or SecurID servers are unavailable. When a user is logged in via 'fallthrough', he is logged in to the port as a non-privileged user. The change takes effect after logging out the port. |
| INT basicPortIdleTimeout | 1.3.6.1.4.1.33.13.1.17.1.12 | INTEGER | read-write | The number of minutes the system will allow a session to have no activity before automatically disconnecting it. A value of -1 indicates no timeout. Zero is not a valid value. Corresponds directly to PORT IDLE TIMEOUT and the value labeled 'Idle Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. |
| CTR basicPortIdleTimeouts | 1.3.6.1.4.1.33.13.1.17.1.22 | Counter | read-only | The number of session disconnects due to expiration of basicPortIdleTimeout. Corresponds directly to the value labeled 'Idle Timeouts:' in the PORT COUNTERS display. |
| INT basicPortIdleTimeReceive | 1.3.6.1.4.1.33.13.1.17.1.43 | INTEGER | read-write | Control to restrict the basicPortIdleTimeout to apply to data received from the network and transmitted out the serial port. Data received by the serial port will not be considered activity. Corresponds directly to the value labeled 'Idle Time Receive Mode:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicPortIdleTimeTransmit | 1.3.6.1.4.1.33.13.1.17.1.44 | INTEGER | read-write | Control to restrict the basicPortIdleTimeout to apply to data received from the serial port and transmitted out the LAN. Data received from the network will not count as activity. Corresponds directly to the value labeled 'Idle Time Transmit Mode:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicPortInactivityLogout | 1.3.6.1.4.1.33.13.1.17.1.13 | INTEGER | read-write | Control for the system automatically logging the port out when it has no sessions, no local activity, and no modem signal changes for the time period specified by basicInactivityTimer. Corresponds directly to PORT INACTIVITY LOGOUT and the presence of the label 'Inactivity Logout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortIndex | 1.3.6.1.4.1.33.13.1.17.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| INT basicPortLastInCharacter | 1.3.6.1.4.1.33.13.1.17.1.24 | INTEGER | read-only | The character that most recently came into the port. Corresponds directly to the value labeled 'Last Char Input:' in the PORT STATUS display. |
| INT basicPortLastOutCharacter | 1.3.6.1.4.1.33.13.1.17.1.25 | INTEGER | read-only | The character that most recently went out of the port. Corresponds directly to the value labeled 'Last Char Output:' in the PORT STATUS display. |
| INT basicPortLockout | 1.3.6.1.4.1.33.13.1.17.1.78 | INTEGER | read-write | Control to prohibit access to this port and send a trap when login authentication fails. One must log out the port for this change to take effect. |
| INT basicPortLogFacilityLevel | 1.3.6.1.4.1.33.13.1.17.1.86 | INTEGER | read-write | Indicates that server originated accounting messages pertaining to this port are logged to the syslog host at this UNIX facility level. If 'none', the server's sessionLogFacility is used. |
| INT basicPortLoginDuration | 1.3.6.1.4.1.33.13.1.17.1.39 | INTEGER | read-write | The amount of time in minutes that a port may remain logged in regardless of the activity on the port. The value 0 indicates that the timer is disabled. Corresponds directly to the value labeled 'Login Duration:' in the PORT ALTERNATE CHARACTERISTICS display. |
| STR basicPortLoginPassword | 1.3.6.1.4.1.33.13.1.17.1.47 | DisplayString | read-write | The password a user must enter to be given the opportunity to log in to a given port. For security reasons reading this object always returns a zero-length value. Corresponds directly to PORT LOGIN PASSWORD. |
| CTR basicPortLogins | 1.3.6.1.4.1.33.13.1.17.1.20 | Counter | read-only | The number of logins on the port since system initialization. Corresponds directly to the value labeled 'Local Accesses:' in the PORT COUNTERS display. |
| INT basicPortLossNotification | 1.3.6.1.4.1.33.13.1.17.1.14 | INTEGER | read-write | Control for the system sending a Bell character to the port when it looses an input character due to an overrun or data error. Corresponds directly to PORT LOSS NOTIFICATION and the presence of the label 'Loss Notification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortMessageCodes | 1.3.6.1.4.1.33.13.1.17.1.15 | INTEGER | read-write | Control for including error numbers in error messages displayed on the port. Corresponds directly to PORT MESSAGE CODES and the presence of the label 'Message Codes' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortMultisessions | 1.3.6.1.4.1.33.13.1.17.1.16 | INTEGER | read-write | Control for running the multisession line protocol between the port and the locally-connected terminal. Corresponds directly to PORT MULTISESSIONS and the presence of the label 'Multisessions' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortOnboardSecurity | 1.3.6.1.4.1.33.13.1.17.1.59 | INTEGER | read-write | A control to toggle onboard security for this port where the username and password are authenticated against an internal access list. The desired change will not take effect until the port is logged off. |
| INT basicPortOutboundSecurity | 1.3.6.1.4.1.33.13.1.17.1.40 | INTEGER | read-write | Control to disable outbound security, which can be either Kerberos or SecureID, on a per port basis. Corresponds directly to the presence of the value 'OutboundSecurity' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display. |
| INT basicPortPortIndex | 1.3.6.1.4.1.33.13.1.21.1.1 | INTEGER | read-only | The value of basicPortIndex for the port to which this session belongs. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| INT basicPortPowerMaster | 1.3.6.1.4.1.33.13.1.17.1.72 | INTEGER | read-write | Control to configure this port as a power master port. This control is only valid on those models with variable configuration ports and which support the power master. This object can only be set enabled, and doing so will disable the previous port type, such as basicPortConsolePort. A set will only update the permanent database. Use a charPortReset for this change to take effect. |
| INT basicPortPowerMasterAlarmSeverity | 1.3.6.1.4.1.33.13.1.17.1.83 | INTEGER | read-write | Control to determine the severity level associated with the trap sent out when the power device is not responding to this port. |
| INT basicPortPowerMasterDeviceStatus | 1.3.6.1.4.1.33.13.1.17.1.84 | INTEGER | read-only | Indicates the current status of the power device controlled by this port. If the device is responding, the status is cleared. Otherwise the status matches the basicPortPowerMasterAlarmSeverity. |
| STR basicPortPowerMasterFirmware | 1.3.6.1.4.1.33.13.1.17.1.77 | DisplayString | read-only | The firmware version of the power master device, which is connected to this port. A response of a null string to a get-request or get-next-request indicates that the power unit attached to this port is not responding with status. |
| STR basicPortPowerMasterModel | 1.3.6.1.4.1.33.13.1.17.1.75 | DisplayString | read-only | The model number of the power master device, which is connected to this port. A response of a null string to a get-request or get-next-request indicates that the power unit attached to this port is not responding with status. |
| STR basicPortPowerMasterSerialNumber | 1.3.6.1.4.1.33.13.1.17.1.76 | DisplayString | read-only | The serial number of the power master device, which is connected to this port. A response of a null string to a get-request or get-next-request indicates that the power unit attached to this port is not responding with status. |
| INT basicPortPowerMasterSwitch | 1.3.6.1.4.1.33.13.1.17.1.74 | INTEGER | read-write | Control to power on or off all of the outlets in the power device attached to this port. A get-request or a get-next- request always returns ready. |
| INT basicPortPowerMasterTimeDelay | 1.3.6.1.4.1.33.13.1.17.1.73 | INTEGER | read-write | Control to set the power up delay interval in milliseconds for the power device attached to this port. A response of 'none' to a get-request or get-next-request may indicate that the power unit attached to this port is not responding with status. |
| INT basicPortPppDialBackup | 1.3.6.1.4.1.33.13.1.17.1.87 | INTEGER | read-write | Indicates whether this port is configured as a PPP dial backup port. This parameter will not take effect until the port is logged out, and this function is restricted to one port. |
| INT basicPortPppDialBackupAddresses | 1.3.6.1.4.1.33.13.1.17.1.94 | INTEGER | read-write | Control to initiate dialing from a dial backup port. In response to get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' after a valid basicPortPppDialBackupLocalAddress and basicPortPppDialBackupDestinationAddress are configured causes the basicPortPppDialBackup port to dial the basicPortPppDialBackupNumbermber. |
| IP basicPortPppDialBackupDestinationAddress | 1.3.6.1.4.1.33.13.1.17.1.93 | IpAddress | read-write | The destination address to use in a PPP dial backup link when the network connection is down and there are SNMP traps to forward. |
| INT basicPortPppDialBackupDisconnectTimer | 1.3.6.1.4.1.33.13.1.17.1.91 | INTEGER | read-write | Indicates the time in seconds that the dial backup link will stay up when there is no more SNMP traffic flowing prior to disconnecting it. |
| IP basicPortPppDialBackupLocalAddress | 1.3.6.1.4.1.33.13.1.17.1.92 | IpAddress | read-write | The local address to use in a PPP dial backup link when the network connection is down and there are SNMP traps to forward. |
| STR basicPortPppDialBackupNumber | 1.3.6.1.4.1.33.13.1.17.1.88 | DisplayString | read-write | The number to dial when a PPP dial backup link is activated, which occurs when the network is down and there are SNMP traps to forward. The port must be a basicPortPppDialBackup port, and it must be logged out for the change to take effect. |
| INT basicPortPppDialBackupRedialRetries | 1.3.6.1.4.1.33.13.1.17.1.90 | INTEGER | read-write | Indicates the number of time to try to dial the backup number before recording an error, logging out the port, and if there are new traps trying to dial again. |
| INT basicPortPppDialBackupRedialTimer | 1.3.6.1.4.1.33.13.1.17.1.89 | INTEGER | read-write | Indicates the time in seconds to wait before redialing the basicPortPppDialBackupNumber on a basicPortPppDialBackup port. |
| INT basicPortRemoteDisconnectNotify | 1.3.6.1.4.1.33.13.1.17.1.32 | INTEGER | read-write | If enabled, a BELL (ctrl G) will be sent out the serial port when a remote session is disconnected and the port is logged out. |
| CTR basicPortRemoteSessions | 1.3.6.1.4.1.33.13.1.17.1.21 | Counter | read-only | The number of remotely originating sessions to the port since system initialization. Corresponds directly to the value labeled 'Remote Accesses:' in the PORT COUNTERS display. |
| INT basicPortRloginTransparentMode | 1.3.6.1.4.1.33.13.1.17.1.38 | INTEGER | read-write | A control to pass x'ff' as binary data, not doubling x'ff'. Similar to basicPortSessionMode = transparent but for a rlogin session. |
| INT basicPortSensor | 1.3.6.1.4.1.33.13.1.17.1.48 | INTEGER | read-write | Control to configure this port as a temperature and humidity sensor. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect. |
| INT basicPortSessEncryption | 1.3.6.1.4.1.33.13.1.22 | INTEGER | read-write | Status of the default encryption value to be set for each session. Corresponds directly to Console Security on SHOW SERVER screen. |
| basicPortSessEntry | 1.3.6.1.4.1.33.13.1.21.1 | not-accessible | Status and parameter values for a basic port session. | |
| INT basicPortSessIndex | 1.3.6.1.4.1.33.13.1.21.1.2 | INTEGER | read-only | The session index in the context of the port, a non-zero positive integer. Session indexes within a port need not be sequential. Session indexes may be reused for different ports. For example, port 1 and port 3 may both have a session 2 at the same time. Session indexes may have any valid integer value, with any meaning convenient to the agent implementation. The session identified by a particular value of this index is the same session as identified by charSessIndex in the standard Character MIB. |
| INT basicPortSessionMode | 1.3.6.1.4.1.33.13.1.17.1.31 | INTEGER | read-write | Data recognition mode for an active session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data noActiveSessions no sessions on this port. This object can be set to values of 1 to 4, but only if there is an active session on the port. |
| basicPortSessionTable | 1.3.6.1.4.1.33.13.1.21 | not-accessible | A list of port session entries. | |
| INT basicPortSignalName | 1.3.6.1.4.1.33.13.1.35.1.2 | INTEGER | read-only | Identification of the hardware signal as specified in RFC1659 as follows: rts Request to Send cts Clear to Send dsr Data Set Ready dts Data Terminal Ready ri Ring Indicator dcd Received Line Signal Detector Some agents do not support DSR since its pin is shared with DCD. |
| INT basicPortStatus | 1.3.6.1.4.1.33.13.1.17.1.23 | INTEGER | read-only | The current operational status of the port. Corresponds directly to the value labeled 'Status:' in the PORT STATUS display. |
| basicPortTable | 1.3.6.1.4.1.33.13.1.17 | not-accessible | A list of basic character port entries. | |
| INT basicPortTl1Console | 1.3.6.1.4.1.33.13.1.17.1.54 | INTEGER | read-write | Controls whether this port becomes the TL1 console receiving and displaying autonomous reports of alarm events. A change takes effect after logging out the port. |
| INT basicPortTl1Mode | 1.3.6.1.4.1.33.13.1.17.1.53 | INTEGER | read-write | Controls the TL1 mode of a port. Valid TL1 modes are human- to-machine language (hml), machine-to-machine language (mml), and MML without echo. MML is for direct connection to another TL1 device whereas HML provides human prompts. A change takes effect after logging out the port. |
| basicPortTrapEntry | 1.3.6.1.4.1.33.13.1.35.1 | not-accessible | Administrative status of signal change traps for a hardware port. | |
| INT basicPortTrapIndex | 1.3.6.1.4.1.33.13.1.35.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by rs232PortIndex in the standard rs232 MIB. |
| INT basicPortTrapStatus | 1.3.6.1.4.1.33.13.1.35.1.3 | INTEGER | read-write | Control to toggle the sending of a trap on a specific signal change on a physical port. One must logout the port prior to this taking effect. |
| basicPortTrapTable | 1.3.6.1.4.1.33.13.1.35 | not-accessible | A list of traps associated with signal control changes on ports. | |
| INT basicPortUnixCommands | 1.3.6.1.4.1.33.13.1.17.1.30 | INTEGER | read-write | Control to allow the user to use Unix-style commands the port. |
| INT basicPortVerification | 1.3.6.1.4.1.33.13.1.17.1.18 | INTEGER | read-write | Control for display of informational messages on the port when the user connects, disconnects, or switches a session. Corresponds directly to PORT VERIFICATION and the presence of the label 'Verification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortXonTimer | 1.3.6.1.4.1.33.13.1.17.1.41 | INTEGER | read-write | Indicates the number of seconds between successive 'XON's sent out a port. A zero signifies that the timer is disabled. Corresponds directly to the value labeled 'Xon Send Timer:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicPortZero | 1.3.6.1.4.1.33.13.1.17.1.28 | INTEGER | read-write | Control to zero counters for the port. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the port's counters to be zeroed. Corresponds to the ZERO PORT command. |
| INT basicPortZeroDisconnectSession | 1.3.6.1.4.1.33.13.1.17.1.45 | INTEGER | read-write | A control to disconnect a session at Port 0 when the password limit is reached. |
| TIK basicPortZeroTime | 1.3.6.1.4.1.33.13.1.17.1.29 | TimeTicks | read-only | The number of hundredths of a second since the most recent zeroing of the port's counters, such as through execution of basicPortZero. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the PORT COUNTERS display. |
| INT basicPowerAlarmTimer | 1.3.6.1.4.1.33.13.1.29 | INTEGER | read-write | The polling interval in seconds for the fuse and power supply status. An alarm trap is issued on power failure. |
| STR basicPowerMasterOutletAmperageStatus | 1.3.6.1.4.1.33.13.1.37.1.5 | DisplayString | read-only | Indicates the current amperage drawn at this outlet. There may be a noticeable time delay while processing a get-request for this object. A null string indicates that amperage status is temporarily unavailable. |
| basicPowerMasterOutletEntry | 1.3.6.1.4.1.33.13.1.37.1 | not-accessible | An entry in the basicPowerMasterOutletTable. | |
| INT basicPowerMasterOutletIndex | 1.3.6.1.4.1.33.13.1.37.1.2 | INTEGER | read-only | An index which uniquely identifies a power master outlet. |
| STR basicPowerMasterOutletName | 1.3.6.1.4.1.33.13.1.37.1.3 | DisplayString | read-write | The name used to identify this power master outlet. |
| INT basicPowerMasterOutletState | 1.3.6.1.4.1.33.13.1.37.1.4 | INTEGER | read-write | Switches the power master outlet on or off. There may be a noticeable time delay while processing a get-request for this object. A response of 'off' to a get-request may indicate that the state is temporarily unavailable. |
| basicPowerMasterOutletTable | 1.3.6.1.4.1.33.13.1.37 | not-accessible | Information about power master outlets. | |
| INT basicPowerMasterPortIndex | 1.3.6.1.4.1.33.13.1.37.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by the charPortIndex in the standard Character MIB. |
| STR basicPowerOutletConsoleName | 1.3.6.1.4.1.33.13.1.26.1.5 | DisplayString | read-write | A name used to identify a console port on a unit with power outlet managment. |
| basicPowerOutletEntry | 1.3.6.1.4.1.33.13.1.26.1 | not-accessible | An entry in the basicPowerOutletTable. | |
| INT basicPowerOutletHighCurrent | 1.3.6.1.4.1.33.13.1.26.1.6 | INTEGER | read-write | A control to indicate a high current unit is attached to this power outlet. When enabled the high current unit will provide current when it detects no power from the power outlet; and will stop the current when the outlet resumes power. This control only works on those InReach devices which support the high current unit such as the IRMGR0. Corresponds directly to the value labeled 'HCNC Setting' in the INREACH MANAGER OUTLET STATUS display. |
| INT basicPowerOutletIndex | 1.3.6.1.4.1.33.13.1.26.1.10 | INTEGER | read-only | An index which uniquely identifies a power outlet. |
| STR basicPowerOutletName | 1.3.6.1.4.1.33.13.1.26.1.3 | DisplayString | read-write | A name used to identify this power outlet. |
| INT basicPowerOutletOnOff | 1.3.6.1.4.1.33.13.1.26.1.1 | INTEGER | read-write | Controls turning on or off the power for the device connected to this power outlet. |
| INT basicPowerOutletReboot | 1.3.6.1.4.1.33.13.1.26.1.2 | INTEGER | read-write | Controls rebooting of the device attached this power outlet. |
| INT basicPowerOutletRedundant | 1.3.6.1.4.1.33.13.1.26.1.4 | INTEGER | read-only | Controls whether power outlets in bank A have redundant outlets in bank B. When enabled, powering on an outlet in bank A will simultaneously power on the corresponding outlet number in bank B. |
| basicPowerOutletTable | 1.3.6.1.4.1.33.13.1.26 | not-accessible | Information about Environmental Manager Power Outlets. | |
| INT basicPowerStatusFuseA | 1.3.6.1.4.1.33.13.1.31 | INTEGER | read-only | Indicates the status of fuse bank A. |
| INT basicPowerStatusFuseB | 1.3.6.1.4.1.33.13.1.32 | INTEGER | read-only | Indicates the status of fuse bank B. |
| INT basicPowerSupplyStatusA | 1.3.6.1.4.1.33.13.1.33 | INTEGER | read-only | Indicates the status of power supply A. |
| INT basicPowerSupplyStatusB | 1.3.6.1.4.1.33.13.1.34 | INTEGER | read-only | Indicates the status of power supply B. |
| STR basicPrivilegedPassword | 1.3.6.1.4.1.33.13.1.6 | DisplayString | read-write | The password a user must enter to become privileged. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER PRIVILEGED PASSWORD. |
| OCT basicSerialPortAPDDefaultProtocol | 1.3.6.1.4.1.33.13.1.18.1.37 | OCTET STRING | read-write | A bit map that specifies the protocol that this port will use when the time specified by basicSerialPortAPDTimeout has expired without sucessfully identifying the incoming porotocol. The bit numbers for the protocols are: None;Logout the port, 1;ARAP, 2;CSLIP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. Only one protocol may be specified for this object |
| OCT basicSerialPortAPDProtocols | 1.3.6.1.4.1.33.13.1.18.1.35 | OCTET STRING | read-write | A bit map that specifies the protocols that this port will attempt to detect using the Auto Protocol Detection function. The bit numbers for the protocols are: 1;ARAP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. More than one of these protocols may be ORed together. The default is 0 (zero) no protocols. |
| INT basicSerialPortAPDTimeout | 1.3.6.1.4.1.33.13.1.18.1.36 | INTEGER | read-write | A time value, in seconds, that specifies how long the port will attempt to determine which protocol is coming into the port. When basicSerialPortAPDTimeout seconds have expired, the port will assume the protocol to use is that specified by basicSerialPortAPDDefaultProtocol. A value of 0 (zero provides an unlimited timeout. |
| INT basicSerialPortAutoHangup | 1.3.6.1.4.1.33.13.1.18.1.39 | INTEGER | read-write | A control that, if enabled, will cause the port to be logged off when the last session on that port is destroyed |
| INT basicSerialPortAutoProtocolDetectPrompt | 1.3.6.1.4.1.33.13.1.18.1.41 | INTEGER | read-write | Controls whether to send the basicAutoProtocolDetectMessage out the serial port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Prompt' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortAutoProtocolDetectSecurityInteractiveOnly | 1.3.6.1.4.1.33.13.1.18.1.44 | INTEGER | read-write | Controls whether Auto Protocol Detect (APD) authentication applies only to interactive users, and not to other APD protocols such as PPP. Corresponds directly to the value labeled 'APD Authentication Interactive Only:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortBackwardSwitch | 1.3.6.1.4.1.33.13.1.18.1.9 | INTEGER | read-write | Character input from the character port to cause a switch to the previous, lower numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT BACKWARD SWITCH and the value labeled 'Backwards Switch:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortBreak | 1.3.6.1.4.1.33.13.1.18.1.2 | INTEGER | read-write | Action to take on a BREAK condition from the port. Corresponds directly to PORT BREAK and the value labeled 'Break:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortBreakLength | 1.3.6.1.4.1.33.13.1.18.1.50 | INTEGER | read-write | Specifies the duration in milliseconds of a remote serial break which is sent via the Telnet Break command. Corresponds directly to the value labeled 'Break Length:' in the PORT CHARACTERISTIC display. |
| INT basicSerialPortCommandSize | 1.3.6.1.4.1.33.13.1.18.1.40 | INTEGER | read-write | Maximum number of input characters to hold in the command buffer. Corresponds directly to the PORT COMMAND SIZE and the value labeled 'Command Size:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortDCDTimeout | 1.3.6.1.4.1.33.13.1.18.1.16 | INTEGER | read-write | The number of milleseconds that DCD may be asserted before disconnecting the port. Corresponds directly to PORT DCD TIMEOUT and the value labeled 'DCD Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| STR basicSerialPortDedicatedKickStartData | 1.3.6.1.4.1.33.13.1.18.1.48 | DisplayString | read-write | A text string which is used to compare at login time to incoming serial data. A match will initiate a telnet session to a dedicated service. Corresponds to the value labeled 'KickStart:' in the PORT CHARACTERISTICS display. |
| STR basicSerialPortDedicatedUserData | 1.3.6.1.4.1.33.13.1.18.1.45 | DisplayString | read-write | The text string to send at the beginning of a connection to a Telnet dedicated service. Corresponds to the value labeled 'UserData:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortDSRLogout | 1.3.6.1.4.1.33.13.1.18.1.14 | INTEGER | read-write | Control for logging out the port when DCD is deasserted. Corresponds directly to PORT DSRLOGOUT and the presence of the label 'DSRlogout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| INT basicSerialPortDSRObserve | 1.3.6.1.4.1.33.13.1.18.1.15 | INTEGER | read-write | Control for beginning the login sequence on the port when DCD is asserted. Corresponds directly to PORT DSRWAIT and the presence of the label 'DSRwait' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| INT basicSerialPortDTRAssert | 1.3.6.1.4.1.33.13.1.18.1.17 | INTEGER | read-write | Control when the system asserts DTR on the port. always unconditional(DISABLED) onConnectionOrRing connection formed or RING asserted(ENABLED) onConnection connection formed (FORCONNECTION) onRing RING asserted (FORRING) Corresponds directly to PORT DTRWAIT and the value labeled 'DTR Wait:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| basicSerialPortEntry | 1.3.6.1.4.1.33.13.1.18.1 | not-accessible | Basic parameter values for a serial port. | |
| INT basicSerialPortForwardSwitch | 1.3.6.1.4.1.33.13.1.18.1.10 | INTEGER | read-write | Character input from the character port to cause a switch to the next, higher numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT FORWARD SWITCH and the value labeled 'Forwards Switch:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortGatewayAutoDiscovery | 1.3.6.1.4.1.33.13.1.18.1.53 | INTEGER | read-write | Control to enable a non-standard method of acquiring the gateway address after boot completes via the bootp protocol. |
| INT basicSerialPortIndex | 1.3.6.1.4.1.33.13.1.18.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| INT basicSerialPortInterrupts | 1.3.6.1.4.1.33.13.1.18.1.3 | INTEGER | read-write | Control for recognizing BREAK or local switch to interrupt a session. Corresponds directly to PORT INTERRUPTS and the presence of the label 'Interrupts' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortIpAutoDiscovery | 1.3.6.1.4.1.33.13.1.18.1.47 | INTEGER | read-write | Control to enable a non-standard method of acquiring the IP address after boot completes via the BOOTP protocol. Corresponds to the value labeled 'IP Address Auto Discovery' in the SERVER CHARACTERISTICS display. |
| INT basicSerialPortIpConfigureBootp | 1.3.6.1.4.1.33.13.1.18.1.57 | INTEGER | read-write | Control to use the BOOTP protocol upon startup to learn the unit's own internet address, subnet mask, primary and secondary gateway servers, domain name servers, time server and domain name. This object was moved to the MRV-IN-REACH-INTERNET-MIB for InReach agent software version V2.4. |
| INT basicSerialPortLimitedCommands | 1.3.6.1.4.1.33.13.1.18.1.18 | INTEGER | read-write | Control for limiting the commands available to the user on the port. Corresponds directly to PORT SECURITY and the presence of the label 'Security' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| INT basicSerialPortLimitedView | 1.3.6.1.4.1.33.13.1.18.1.19 | INTEGER | read-write | Control for restricting what a user may display. Corresponds directly to PORT LIMITED VIEW and the presence of the label 'Limited View' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortLineEditor | 1.3.6.1.4.1.33.13.1.18.1.21 | INTEGER | read-write | Control for allowing the user to use local mode command line editing. Corresponds directly to PORT LINE EDITOR and the presence of the label 'Line Editor' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortLineEditorBackspace | 1.3.6.1.4.1.33.13.1.18.1.22 | INTEGER | read-write | Character input from the character port to move the cursor to the left. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BACKSPACE and the value labeled 'Backspace Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorBeginning | 1.3.6.1.4.1.33.13.1.18.1.23 | INTEGER | read-write | Character input from the character port to move the cursor to the beginning of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BEGINNING and the value labeled 'Begin Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorCancel | 1.3.6.1.4.1.33.13.1.18.1.24 | INTEGER | read-write | Character input from the character port to cancel an interactive dialog or delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR CANCEL and the value labeled 'Cancel Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorDeleteBeginning | 1.3.6.1.4.1.33.13.1.18.1.25 | INTEGER | read-write | Character input from the character port to delete the current line from the cursor to the beginning. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE BEGINNING and the value labeled 'Delete Begin Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorDeleteLine | 1.3.6.1.4.1.33.13.1.18.1.26 | INTEGER | read-write | Character input from the character port to delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE LINE and the value labeled 'Delete Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorEnd | 1.3.6.1.4.1.33.13.1.18.1.27 | INTEGER | read-write | Character input from the character port to move the cursor to the end of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR END and the value labeled 'End of Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorForward | 1.3.6.1.4.1.33.13.1.18.1.28 | INTEGER | read-write | Character input from the character port to move the cursor to the right. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR FORWARDS and the value labeled 'Forwards Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorInsertToggle | 1.3.6.1.4.1.33.13.1.18.1.29 | INTEGER | read-write | Character input from the character port to toggle between insert and overwrite modes. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR INSERT TOGGLE and the value labeled 'Insert Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorNextLine | 1.3.6.1.4.1.33.13.1.18.1.30 | INTEGER | read-write | Character input from the character port to recall the next, newer line in the command history. The value -1 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR NEXT LINE and the value labeled 'Next Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorPreviousLine | 1.3.6.1.4.1.33.13.1.18.1.31 | INTEGER | read-write | Character input from the character port to recall the previous, older line in the command history. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR PREVIOUS LINE and the value labeled 'Previous Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorQuotingCharacter | 1.3.6.1.4.1.33.13.1.18.1.32 | INTEGER | read-write | Character input from the character port to inhibit interpretation of the next input character. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR QUOTING CHARACTER and the value labeled 'Quoting Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorRedisplay | 1.3.6.1.4.1.33.13.1.18.1.33 | INTEGER | read-write | Character input from the character port to redisplay the current command line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR REDISPLAY CHARACTER and the value labeled 'Redisplay Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLocalSwitch | 1.3.6.1.4.1.33.13.1.18.1.11 | INTEGER | read-write | Character input from the character port to cause a switch to local command mode. The value 0 indicates no character has this effect. Corresponds directly to PORT LOCAL SWITCH and the value labeled 'Local Switch:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortModemControl | 1.3.6.1.4.1.33.13.1.18.1.12 | INTEGER | read-write | Control for observing hardware modem control signals. Corresponds directly to PORT MODEM CONTROL and the value labeled 'Modem Control:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| INT basicSerialPortNoLoss | 1.3.6.1.4.1.33.13.1.18.1.4 | INTEGER | read-write | Control for storing port input locally in anticipation of session startup. Corresponds directly to PORT NOLOSS and the presence of the label 'Noloss' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortPassword | 1.3.6.1.4.1.33.13.1.18.1.20 | INTEGER | read-write | Control for requiring the user to supply the login password to log in on the port. Corresponds directly to PORT PASSWORD and the presence of the label 'Password' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| STR basicSerialPortPasswordPrompt | 1.3.6.1.4.1.33.13.1.18.1.43 | DisplayString | read-write | The text string used to prompt for a user's password. Corresponds directly to the value labeled 'Password Prompt:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortPause | 1.3.6.1.4.1.33.13.1.18.1.5 | INTEGER | read-write | Control for pausing after each screenful of locally-originated output to the port. Corresponds directly to PORT PAUSE and the presence of the label 'Pause' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| STR basicSerialPortPrompt | 1.3.6.1.4.1.33.13.1.18.1.6 | DisplayString | read-write | Prompt for the system to use on the port. Corresponds directly to PORT PROMPT and the value labeled 'Prompt:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortQuadartReceiveDiscard | 1.3.6.1.4.1.33.13.1.18.1.34 | INTEGER | read-write | Control for discard of received errors from quadart hardware. |
| INT basicSerialPortRaiseControlDtr | 1.3.6.1.4.1.33.13.1.18.1.56 | INTEGER | read-write | Controls the ability to change the state of DTR using basicSerialPortRaiseLowerDTR. This characteristic is not intended for use with modem ports. Corresponds directly to the presence of 'Control DTR' under the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off. |
| INT basicSerialPortRaiseLowerDtr | 1.3.6.1.4.1.33.13.1.18.1.55 | INTEGER | read-write | A control to to raise or lower the DTR signal from this port by setting it to high or low, respectively. This request will have no effect unless basicSerialPortRaiseControlDtr is enabled. In response to a get-request or get-next-request the agent always returns low for this object. |
| INT basicSerialPortRotaryRoundRobin | 1.3.6.1.4.1.33.13.1.18.1.51 | INTEGER | read-write | Controls whether a port which participates in an internet rotary is selected in round robin or fixed priority order. Corresponds directly to the value labeled 'Round Robin search:' in the SERVER INTERNET ROTARY display. |
| INT basicSerialPortSignalCheck | 1.3.6.1.4.1.33.13.1.18.1.13 | INTEGER | read-write | Control for observing DSR and DCD to bound allowing sessions. Corresponds directly to PORT SIGNAL CHECK and the presence of the label 'Signal Check' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220). |
| INT basicSerialPortSubnetAutoDiscovery | 1.3.6.1.4.1.33.13.1.18.1.54 | INTEGER | read-write | Control to enable a non-standard method of acquiring the subnet mask after boot completes via the bootp protocol. |
| basicSerialPortTable | 1.3.6.1.4.1.33.13.1.18 | not-accessible | A list of basic character serial port entries. | |
| INT basicSerialPortTerminalType | 1.3.6.1.4.1.33.13.1.18.1.7 | INTEGER | read-write | Type of terminal attached to the port, for formatting local output. Corresponds directly to PORT TYPE and the value labeled 'Type:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortTypeaheadLimit | 1.3.6.1.4.1.33.13.1.18.1.8 | INTEGER | read-write | Maximum number of input characters to hold pending tranmission on a session. Corresponds directly to PORT TYPEAHEAD SIZE and the value labeled 'Typeahead Size:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortUsernameCharSet | 1.3.6.1.4.1.33.13.1.18.1.38 | INTEGER | read-write | A control, that if set to seven-bit, will allow only the ASCII printable characters in the range SP (X20) to ~ (X7E) in the username field. A value of none allows any character |
| STR basicSerialPortUsernamePrompt | 1.3.6.1.4.1.33.13.1.18.1.42 | DisplayString | read-write | The text string used to prompt for a user's name. Corresponds directly to the value labeled 'Username Prompt:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortWelcomeBeforeAuthentication | 1.3.6.1.4.1.33.13.1.18.1.52 | INTEGER | read-write | Control to display the basicWelcome message prior to authenticating the user. Corresponds to the presence of the value 'Welcome-Banner-Pre-Authentication' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display. |
| INT basicSessControlled | 1.3.6.1.4.1.33.13.1.21.1.3 | INTEGER | read-only | A control to send preconfigured controlled port session strings out the serial port when entering or exiting this session. Corresponds directly to the value labeled 'Controlled' under the Service Mode header in the SESSION display. |
| GAU basicSessions | 1.3.6.1.4.1.33.13.1.14 | Gauge | read-only | The total number of connected sessions. Corresponds directly to the value labeled 'Connected Sessions:' and 'Cur' in the SERVER STATUS display. |
| GAU basicSessionsHigh | 1.3.6.1.4.1.33.13.1.15 | Gauge | read-only | The highest value of basicSessions since system initialization. Corresponds directly to the value labeled 'Connected Sessions:' and 'High' in the SERVER STATUS display. |
| INT basicSessionsLimit | 1.3.6.1.4.1.33.13.1.16 | INTEGER | read-write | The maximum total number of sessions that can simultaneously be connected to the system. A value of -1 indicates no limit up to available dynamic system memory. Corresponds directly to SERVER SESSION LIMIT and the value labeled 'Connected Sessions:' and 'Max' in the SERVER STATUS display. |
| INT basicTemperatureAlarmSeverity | 1.3.6.1.4.1.33.13.1.27.1.1.5 | INTEGER | read-write | Control to determine the severity level associated with the trap sent out when the temperature reading is out-of-bounds. |
| INT basicTemperatureAlarmStatus | 1.3.6.1.4.1.33.13.1.27.1.1.6 | INTEGER | read-only | Indicates the current status of the temperature sensor. If the basicTemperatureValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level. |
| basicTemperatureHumiditySensor | 1.3.6.1.4.1.33.13.1.27 | |||
| STR basicTemperatureHumiditySensorName | 1.3.6.1.4.1.33.13.1.27.1.1.7 | DisplayString | read-write | The name used to identify this temperature sensor. |
| INT basicTemperatureSensor | 1.3.6.1.4.1.33.13.1.27.1.1.3 | INTEGER | read-write | Controls the enabling or disabling of a temperature sensor. |
| basicTemperatureSensorEntry | 1.3.6.1.4.1.33.13.1.27.1.1 | not-accessible | An entry in the basicTemperatureSensorTable. | |
| INT basicTemperatureSensorIndex | 1.3.6.1.4.1.33.13.1.27.1.1.10 | INTEGER | read-only | An index which uniquely identifies a temperature sensor. |
| basicTemperatureSensorTable | 1.3.6.1.4.1.33.13.1.27.1 | not-accessible | Information about Environmental Manager Temperature Sensors. | |
| INT basicTemperatureUnits | 1.3.6.1.4.1.33.13.1.23 | INTEGER | read-write | Indicates the units of measurement for the temperature sensors. |
| INT basicTemperatureValue | 1.3.6.1.4.1.33.13.1.27.1.1.4 | INTEGER | read-write | The current temperature reading for this sensor. |
| INT basicTempTrapHighThreshold | 1.3.6.1.4.1.33.13.1.27.1.1.1 | INTEGER | read-write | The temperature at or above which a sensorThresholdTrap is generated. |
| INT basicTempTrapLowThreshold | 1.3.6.1.4.1.33.13.1.27.1.1.2 | INTEGER | read-write | The temperature at or below which a sensorThresholdTrap is generated. |
| STR basicWelcome | 1.3.6.1.4.1.33.13.1.9 | DisplayString | read-write | The text string the server displays before attempting to log in a user. Corresponds directly to SERVER WELCOME and the value labeled 'Welcome:' in the SERVER CHARACTERISTICS display. |
| broadcastGroupEntry | 1.3.6.1.4.1.33.13.8.1.1 | not-accessible | Broadcast group information. | |
| INT broadcastGroupIndex | 1.3.6.1.4.1.33.13.8.1.1.1 | INTEGER | read-only | An index value that uniquely identifies a broadcast group. |
| INT broadcastGroupMaster | 1.3.6.1.4.1.33.13.8.1.1.3 | INTEGER | read-write | An index value that uniquely identifies the Master Broadcast Port for this group. The port provided in this object is the same port as identified by charPortIndex in the standard Character MIB. |
| OCT broadcastGroupSlaves | 1.3.6.1.4.1.33.13.8.1.1.4 | OCTET STRING | read-write | A bitmap representing the ports included in this broadcast group. A bit with a value of '1' means the corresponding port is included in the broadcast group whereas a value of '0' indicates that the port is not part of the broadcast group. |
| OCT broadcastGroupSlavesBroadcastOnly | 1.3.6.1.4.1.33.13.8.1.1.5 | OCTET STRING | read-write | A bitmap representing the ports set up to discard input data and transmit only the broadcast data on the line. A bit set to '1' means that the corresponding port will only broadcast the data and discard any input. |
| INT broadcastGroupSlaveTcpBroadcastOnly | 1.3.6.1.4.1.33.13.8.1.1.7 | INTEGER | read-write | Specifies whether the TCP port will discard input characters for the Master port so that the Master port operates in broadcast only mode. |
| INT broadcastGroupSlaveTcpPort | 1.3.6.1.4.1.33.13.8.1.1.6 | INTEGER | read-write | A TCP port number on which the broadcast group process will listen for incoming TCP connections. A client connected to this particular port will receive the data broadcast by the Master Port. A value of '0' indicates that no TCP port is defined. |
| INT broadcastGroupStatus | 1.3.6.1.4.1.33.13.8.1.1.2 | INTEGER | read-write | A status value for the broadcast group. The value 'enabled' means that the group is active and broadcasting data whereas 'disabled' means that the group is not active. |
| broadcastGroupTable | 1.3.6.1.4.1.33.13.8.1 | not-accessible | A list of broadcast groups. | |
| cclParsedScriptEntry | 1.3.6.1.4.1.33.13.7.1.1 | not-accessible | Parsed CCL script information. | |
| cclParsedScriptTable | 1.3.6.1.4.1.33.13.7.1 | not-accessible | A list of parsed CCL scripts. | |
| STR cclPortCclName | 1.3.6.1.4.1.33.13.7.2.1.1 | DisplayString | read-write | The name of the ARAP modem CCL script file. |
| cclPortEntry | 1.3.6.1.4.1.33.13.7.2.1 | not-accessible | CCL parameter values for a port. | |
| INT cclPortModemAudible | 1.3.6.1.4.1.33.13.7.2.1.2 | INTEGER | read-write | This boolean indicates if the CCL script should put the modem into audible mode. |
| cclPortTable | 1.3.6.1.4.1.33.13.7.2 | not-accessible | A list of ccl character port entries. | |
| INT cclScriptControl | 1.3.6.1.4.1.33.13.7.1.1.2 | INTEGER | read-write | Control for maintaining the CCL script. The refresh action consists of retrieving the script by name from a script server and parsing it into an executable format. This may be used to add an entry to the table or refresh an existing entry with a new version of the CCL script from the server. This command may take ten seconds or more to complete and may fail if the script file cannot be retrieved or an error is encountered in parsing the CCL script. An error value of genErr is returned upon refresh failure. The refresh action corresponds directly to the commnd: REFRESH SERVER CCL. Setting this field to delete causes a script that is NOT being referenced by any ports to be removed from the list and its memory freed. This action corresponds directly to the command: DELETE SERVER CCL. An error value of badValue is returned upon delete failure. |
| STR cclScriptName | 1.3.6.1.4.1.33.13.7.1.1.1 | DisplayString | read-only | The name of a CCL script file that has been loaded from a script server. Corresponds directly to the name in a SERVER CCL command and the value labeled 'CCL name:' in the PORT CHARACTERISTICS display. |
| characterDep | 1.3.6.1.4.1.33.2 | |||
| NTF contactClosureChanged | 1.3.6.1.4.1.33.0.30 | Indication that the contact closure transitioned to open or closed. | ||
| INT dialPortDialback | 1.3.6.1.4.1.33.13.5.1.1.2 | INTEGER | read-write | Control for use of dialback when a user logs in on the port. Corresponds directly to PORT DIALBACK and the presence of the label 'Dialback' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT dialPortDialbackNoUsername | 1.3.6.1.4.1.33.13.5.1.1.5 | INTEGER | read-write | Control which when enabled on a dialback port will not prompt for a username upon dialing back. Instead the original username is reused. |
| INT dialPortDialbackTimeout | 1.3.6.1.4.1.33.13.5.1.1.3 | INTEGER | read-write | The number of seconds to wait for remote modem response when dialing back. Corresponds directly to PORT DIALBACK TIMEOUT and the value labeled 'Dialback Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT dialPortDialout | 1.3.6.1.4.1.33.13.5.1.1.4 | INTEGER | read-write | A control to determine the state of a remote port after it has been logged out from the remote side of the connection. none will log out the port, query will ask user what to do, slip and ppp will revert to those protocols |
| dialPortEntry | 1.3.6.1.4.1.33.13.5.1.1 | not-accessible | Dial parameter values for a port. | |
| INT dialPortIndex | 1.3.6.1.4.1.33.13.5.1.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| dialPortTable | 1.3.6.1.4.1.33.13.5.1 | not-accessible | A list of dial character port entries. | |
| NTF humidityNormal | 1.3.6.1.4.1.33.0.45 | Indication that the humidity returned within bounds, and the currrent humidity reading. | ||
| NTF humidityThresholdExceeded | 1.3.6.1.4.1.33.0.37 | Indication that the humidity exceeded a threshhold and the value of the currrent humidity. | ||
| IP icmpPingHostAddress | 1.3.6.1.4.1.33.13.9.1.1.2 | IpAddress | read-write | The host address to be monitored to make sure it is reachable using ICMP pings. This address must be unique within the table, and must be Set to a non-zero value prior to configuring the other attributes of the ping host. A set-request with an IpAddress of zero will make this entry inactive. |
| STR icmpPingHostDescription | 1.3.6.1.4.1.33.13.9.1.1.3 | DisplayString | read-write | This is an optional description of the ping host. |
| INT icmpPingHostIndex | 1.3.6.1.4.1.33.13.9.1.1.1 | INTEGER | read-only | An index value that uniquely identifies a ping host. |
| INT icmpPingHostMaximumRetries | 1.3.6.1.4.1.33.13.9.1.1.6 | INTEGER | read-write | The maximum consecutive failed attempts to reach the host via ICMP ping before sending notification as specified by icmpPingHostNotificationType. |
| INT icmpPingHostNotificationType | 1.3.6.1.4.1.33.13.9.1.1.4 | INTEGER | read-write | Indicates the type of notification used, if any, when the ping host is determined to be unreachable. If the type is snmp, a trap is sent to configured trap clients. |
| NTF icmpPingHostNotReachable | 1.3.6.1.4.1.33.0.50 | Indication that the icmp Ping Host is not reachable after polling for icmpPingHostMaximumRetries. | ||
| INT icmpPingHostPollingInterval | 1.3.6.1.4.1.33.13.9.1.1.5 | INTEGER | read-write | The time in seconds between sending an ICMP ping to a ping host in order to check for reachability. |
| NTF icmpPingHostResponding | 1.3.6.1.4.1.33.0.51 | Indication that the icmp Ping Host is reachable again after a failure. | ||
| INT icmpPingHostStatus | 1.3.6.1.4.1.33.13.9.1.1.8 | INTEGER | read-only | Indicates the current status of the ping host. If the host is reachable, the status is cleared. Otherwise, it is the same as the icmpPingHostTrapSeverityLevel. |
| INT icmpPingHostTrapSeverityLevel | 1.3.6.1.4.1.33.13.9.1.1.7 | INTEGER | read-write | Indicates the severity level of a trap to be sent out when the host is unreachable. |
| STR menuCommand | 1.3.6.1.4.1.33.13.3.4.1.4 | DisplayString | read-write | The commands to execute when the user chooses the menu entry. Corresponds directly second line following the entry number in the SERVER MENU display. |
| STR menuContinuePrompt | 1.3.6.1.4.1.33.13.3.2 | DisplayString | read-write | The text to use when prompting a menu user to press RETURN to continue. Corresponds directly to SERVER MENU CONTINUE PROMPT and the value labeled 'Menu Continue Prompt:' in the SERVER MENU display. |
| menuEntry | 1.3.6.1.4.1.33.13.3.4.1 | not-accessible | Parameter values for a menu entry. | |
| INT menuIndex | 1.3.6.1.4.1.33.13.3.4.1.1 | INTEGER | read-only | The index number of a menu entry. Corresponds directly to the numbers down the left of the SERVER MENU display. |
| INT menuNestedEthernet | 1.3.6.1.4.1.33.13.3.9 | INTEGER | read-write | Control to request to download a menu script which is unique for this unit by prepending the Ethernet address, or 802.3 MAC address, of this unit to the nestedMenuName. |
| STR menuNestedName | 1.3.6.1.4.1.33.13.3.6 | DisplayString | read-write | Name of the script file containing the nested menu. |
| INT menuNestedScriptMaximum | 1.3.6.1.4.1.33.13.3.7 | INTEGER | read-write | Maximum number of temporary storage bytes for a nested menu script file. If not zero, the nested menu function is enabled. |
| INT menuNestedSystemName | 1.3.6.1.4.1.33.13.3.8 | INTEGER | read-write | Control to request to download a menu script which is unique for this unit by prepending the sysLocalName of this unit to the nestedMenuName. |
| GAU menuNumber | 1.3.6.1.4.1.33.13.3.1 | Gauge | read-only | The number of entries in the Menu table. Corresponds indirectly to SERVER MENU display. |
| menuPortEntry | 1.3.6.1.4.1.33.13.3.5.1 | not-accessible | Menu parameter values for a port. | |
| INT menuPortIndex | 1.3.6.1.4.1.33.13.3.5.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| INT menuPortMenuStatus | 1.3.6.1.4.1.33.13.3.5.1.2 | INTEGER | read-write | Control for menu operation on the port. Corresponds indirectly to PORT MENU and PORT PRIVILEGED MENU and the presence of the labels 'Menu' and 'Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT menuPortNestedMenuPrivilege | 1.3.6.1.4.1.33.13.3.5.1.4 | INTEGER | read-write | Control for nested privileged menu operation on the port. Corresponds indirectly to PORT NESTED PRIVILEGED MENU and the presence of the label 'Nested Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT menuPortNestedMenuStatus | 1.3.6.1.4.1.33.13.3.5.1.3 | INTEGER | read-write | Control for nested menu operation on the port. Corresponds indirectly to PORT NESTED MENU and the presence of the label 'Nested Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT menuPortNestedTopLevel | 1.3.6.1.4.1.33.13.3.5.1.5 | INTEGER | read-write | The top level nested menu to select from the menu definition file. |
| menuPortTable | 1.3.6.1.4.1.33.13.3.5 | not-accessible | A list of menu-related character port entries. | |
| STR menuSelectionPrompt | 1.3.6.1.4.1.33.13.3.3 | DisplayString | read-write | The text to use when prompting a menu user for a menu selection. Corresponds directly to SERVER MENU PROMPT and the value labeled 'Menu Prompt:' in the SERVER MENU display. |
| INT menuStatus | 1.3.6.1.4.1.33.13.3.4.1.2 | INTEGER | read-write | The status of a the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER MENU command. Actual removal of the entry is implementation specific. |
| menuTable | 1.3.6.1.4.1.33.13.3.4 | not-accessible | A list of menu entries. | |
| STR menuText | 1.3.6.1.4.1.33.13.3.4.1.3 | DisplayString | read-write | The text to be displayed in the menu. Corresponds directly to the line next to the entry number in the SERVER MENU display. |
| INT netLoginNumber | 1.3.6.1.4.1.33.13.4.1 | INTEGER | read-only | The number of entries in the Network Login Server table. |
| netLoginPortEntry | 1.3.6.1.4.1.33.13.4.3.1 | not-accessible | Network login parameter values for a port. | |
| STR netLoginPortExecuteFile | 1.3.6.1.4.1.33.13.4.3.1.7 | DisplayString | read-write | The path and file name of a script to be executed immediately on the port. Corresponds directly the file name in the SCRIPT command. |
| INT netLoginPortIndex | 1.3.6.1.4.1.33.13.4.3.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| OCT netLoginPortLoaderAddress | 1.3.6.1.4.1.33.13.4.3.1.5 | OCTET STRING | read-only | The network address of the server that provided the script for the current port login. Corresponds directly the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display. |
| ADR netLoginPortLoaderAddressType | 1.3.6.1.4.1.33.13.4.3.1.4 | AddressType | read-only | The type of network address contained in netLoginPortLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display. |
| STR netLoginPortLoaderFile | 1.3.6.1.4.1.33.13.4.3.1.6 | DisplayString | read-only | The path and file name of the script used for the current port login. Corresponds directly the file name part of the value labeled 'Script Loaded From:' in the PORT STATUS display. |
| INT netLoginPortScriptEcho | 1.3.6.1.4.1.33.13.4.3.1.3 | INTEGER | read-write | Control for display of script operation on the port when running a script. Corresponds directly to PORT SCRIPT ECHO and the presence of the label 'Script Echo' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT netLoginPortScriptUse | 1.3.6.1.4.1.33.13.4.3.1.2 | INTEGER | read-write | Control for the script action taken when a user logs in on the port. Corresponds directly to PORT SCRIPT LOGIN and the value labeled 'Script Login:' in the PORT ALTERNATE CHARACTERISTICS display. |
| netLoginPortTable | 1.3.6.1.4.1.33.13.4.3 | not-accessible | A list of network login character port entries. | |
| netLoginServerEntry | 1.3.6.1.4.1.33.13.4.2.1 | not-accessible | Network login parameter values for a server entry. | |
| STR netLoginServerName | 1.3.6.1.4.1.33.13.4.2.1.1 | DisplayString | read-only | The name of a network login server, suitable for resolution to a network address. Corresponds directly to host portion of SERVER SCRIPT SERVER and the value labeled 'Script Host' in the SERVER PARAMETER SERVER display. |
| STR netLoginServerPath | 1.3.6.1.4.1.33.13.4.2.1.3 | DisplayString | read-write | The full path name to the script file that is identified by the user name. Corresponds directly to path portion of SERVER SCRIPT SERVER and the value labeled 'Script Path' in the SERVER PARAMETER SERVER display. Defaults to the NULL string when a new entry is created. |
| STR netLoginServerSeparator | 1.3.6.1.4.1.33.13.4.2.1.4 | DisplayString | read-write | The single character string that will be inserted between the components of a file's path on the script server. Defaults to the NULL string when a new entry is created. Corresponds directly to the separator portion of SERVER SCRIPT SERVER display. |
| INT netLoginServerStatus | 1.3.6.1.4.1.33.13.4.2.1.2 | INTEGER | read-write | Status of this entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER SCRIPT SERVER command. Actual removal of the entry is implementation specific. |
| netLoginServerTable | 1.3.6.1.4.1.33.13.4.2 | not-accessible | A list of network login server entries. | |
| pingHostsEntry | 1.3.6.1.4.1.33.13.9.1.1 | not-accessible | Ping Hosts information. | |
| pingHostsTable | 1.3.6.1.4.1.33.13.9.1 | not-accessible | A list of ICMP ping hosts. | |
| NTF portInputSignalChange | 1.3.6.1.4.1.33.0.35 | Indicates that an input signal on a port has transitioned to the state indicated in the variable rs232InSigState. | ||
| NTF portOutputSignalChange | 1.3.6.1.4.1.33.0.36 | Indicates that an output signal on a port has transitioned to the state indicated in the variable rs232OutSigState. | ||
| NTF powerAlarmFuseBankA | 1.3.6.1.4.1.33.0.31 | Indicates that a fuse from bank A tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working. | ||
| NTF powerAlarmFuseBankB | 1.3.6.1.4.1.33.0.32 | Indicates that a fuse from bank B tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working. | ||
| NTF powerMasterNotResponding | 1.3.6.1.4.1.33.0.43 | Indication that the power management port lost or regained contact with the power unit to which it was connected as indicated by the basicPortPowerMasterDeviceStatus variable. | ||
| NTF powerSupplyAlarmA | 1.3.6.1.4.1.33.0.33 | Indicates that power supply A lost or regained power. However, it is unlikely that a trap would be issued when the power comes on. | ||
| NTF powerSupplyAlarmB | 1.3.6.1.4.1.33.0.34 | Indicates that power supply B lost or regained power. However, it is unlikely that a trap would be issued when the power comes on. | ||
| queueEntry | 1.3.6.1.4.1.33.13.2.4.1 | not-accessible | Parameter values for a queue entry. | |
| GAU queueHigh | 1.3.6.1.4.1.33.13.2.2 | Gauge | read-only | The highest value of queueNumber since system initialization. Corresponds directly to the value labeled 'Queue Entries' and 'High' in the SERVER STATUS display. |
| INT queueJob | 1.3.6.1.4.1.33.13.2.4.1.1 | INTEGER | read-only | The job number of a queued request. Corresponds directly to the value labeled 'Entry' in the QUEUE display. |
| INT queueLimit | 1.3.6.1.4.1.33.13.2.1 | INTEGER | read-write | The maximum number of entries that can be made in the Queue table. The value -1 indicates the imit is available memory. Corresponds directly to SERVER QUEUE LIMIT and the value labeled 'Queue Limit:' in the SERVER CHARACTERISTICS display. |
| GAU queueNumber | 1.3.6.1.4.1.33.13.2.3 | Gauge | read-only | The number of entries in the Queue table. Corresponds directly to the value labeled 'Queue Entries' and 'Cur' in the SERVER STATUS display. |
| queuePortEntry | 1.3.6.1.4.1.33.13.2.5.1 | not-accessible | Queuing parameter values for a port. | |
| INT queuePortIndex | 1.3.6.1.4.1.33.13.2.5.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. |
| INT queuePortQueuing | 1.3.6.1.4.1.33.13.2.5.1.2 | INTEGER | read-write | Control for allowing queued requests for using the port. Corresponds directly to PORT QUEUING and the presence of the label 'Queuing' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| queuePortTable | 1.3.6.1.4.1.33.13.2.5 | not-accessible | A list of queuing-related character port entries. | |
| STR queueServiceName | 1.3.6.1.4.1.33.13.2.4.1.4 | DisplayString | read-only | The name of the service for which the originator is waiting. Corresponds directly to the value labeled 'Service' in the QUEUE display. |
| INT queueServicePortIndex | 1.3.6.1.4.1.33.13.2.4.1.5 | INTEGER | read-only | The charPortIndex of the port for which the originator is waiting, if supplied by the originator. As defined in the standard Character MIB. Corresponds indirectly to the port number part of the value labeled 'Port Name' in the QUEUE display. |
| STR queueServicePortName | 1.3.6.1.4.1.33.13.2.4.1.6 | DisplayString | read-only | The name of the port for which the originator is waiting, if supplied by the originator. Corresponds directly to the port name part of the value labeled 'Port Name' in the SERVER QUEUE display. |
| STR queueSourceName | 1.3.6.1.4.1.33.13.2.4.1.3 | DisplayString | read-only | The name of the system that originated the queue entry. Corresponds directly to the value labeled 'Source Node' in the QUEUE display. |
| INT queueStatus | 1.3.6.1.4.1.33.13.2.4.1.2 | INTEGER | read-write | The status of a queue entry. Set to 'invalid' to remove the entry, which corresponds directly to the REMOVE QUEUE ENTRY command. Actual removal of the entry is implementation specific. |
| queueTable | 1.3.6.1.4.1.33.13.2.4 | not-accessible | A list of queue entries. | |
| INT sessionLogConnectionID | 1.3.6.1.4.1.33.13.6.2.1.2 | INTEGER | read-only | An indentifying number for records relating to the same connection, that is, the connect and disconnect records, either of which can be missing. Corresponds directly to value labeled 'Entry' the SERVER ACCOUNTING display. |
| DAT sessionLogConnectTime | 1.3.6.1.4.1.33.13.6.2.1.8 | DateTime | read-only | The date and time that session connection occurred. Corresponds directly to the value labeled 'Connect Time' in the SERVER ACCOUNTING display. |
| DAT sessionLogDisconnectTime | 1.3.6.1.4.1.33.13.6.2.1.9 | DateTime | read-only | The date and time that session disconnection occurred. Corresponds directly to the value labeled 'Disconnect Time' in the SERVER ACCOUNTING display. |
| INT sessionLogEmpty | 1.3.6.1.4.1.33.13.6.7 | INTEGER | read-write | Control to empty the log. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the log to be emptied. |
| sessionLogEntry | 1.3.6.1.4.1.33.13.6.2.1 | not-accessible | Parameter values for a session log entry. | |
| INT sessionLogEvent | 1.3.6.1.4.1.33.13.6.2.1.4 | INTEGER | read-only | The type of event. Corresponds directly to the alphabetic part of the value labeled 'Type' in the SERVER ACCOUNTING display. Type 15 is used by internal processes that call the session log function with an already formatted message. |
| INT sessionLogEventDetail | 1.3.6.1.4.1.33.13.6.2.1.5 | INTEGER | read-only | The detailed reason for the event. Corresponds directly to the numeric part of the value labeled 'Type' in the SERVER ACCOUNTING display. |
| INT sessionLogFacility | 1.3.6.1.4.1.33.13.6.8 | INTEGER | read-write | The UNIX facility level that server originated accounting messages are logged to. |
| OCT sessionLogHostAddress | 1.3.6.1.4.1.33.13.6.4 | OCTET STRING | read-write | The address of the host to receive events. |
| OCT sessionLogHostSecondaryAddress | 1.3.6.1.4.1.33.13.6.11 | OCTET STRING | read-write | The address of a secondary host to receive events. Corresponds directly to the value labeled 'SYSLOGD Host2' in the SERVER UNIT display. |
| INT sessionLogHostSecondaryType | 1.3.6.1.4.1.33.13.6.10 | INTEGER | read-write | The type of secondary host to which session log events are to be sent. This value should be set to unix when configuring a non-zero sessionLogHostSecondaryAddress. Corresponds to the presence of the label 'SYSLOGD Host2' following the label 'Daemon(s)' in the SERVER UNIT display. |
| INT sessionLogHostType | 1.3.6.1.4.1.33.13.6.3 | INTEGER | read-write | The type of host to which session log events are to be sent. |
| CTR sessionLogInCharacters | 1.3.6.1.4.1.33.13.6.2.1.10 | Counter | read-only | The number of characters that came into the port for the session. Corresponds directly to the value labeled 'Bytes In' in the SERVER ACCOUNTING display. |
| INT sessionLogIndex | 1.3.6.1.4.1.33.13.6.2.1.1 | INTEGER | read-only | The index number of a session log entry. Corresponds directly to the order of the displayed records in the SERVER ACCOUNTING display. The maximum value is sessionLogLimit. |
| INT sessionLogLimit | 1.3.6.1.4.1.33.13.6.1 | INTEGER | read-write | The maximum number of entries allowed in the Session Log table. Corresponds directly to SERVER ACCOUNTING ENTRIES and the value labeled 'Accounting Entries:' in the SERVER CHARACTERISTICS display. |
| CTR sessionLogOutCharacters | 1.3.6.1.4.1.33.13.6.2.1.11 | Counter | read-only | The number of characters that went out of the port for the session. Corresponds directly to the value labeled 'Bytes Out' in the SERVER ACCOUNTING display. |
| INT sessionLogPort | 1.3.6.1.4.1.33.13.6.2.1.3 | INTEGER | read-only | An index value that uniquely identifies the port where the event took place. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. Corresponds directly to the value labeled 'Port' in the SERVER ACCOUNTING display. |
| INT sessionLogPriority | 1.3.6.1.4.1.33.13.6.6 | INTEGER | read-write | The largest priority number for the system to log. Higher numbered (lower priority) events will not be logged. |
| INT sessionLogReliable | 1.3.6.1.4.1.33.13.6.9 | INTEGER | read-write | Control for reliable logging. Corresponds directly to the presence of the label 'Reliable Accounting' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| STR sessionLogRemoteName | 1.3.6.1.4.1.33.13.6.2.1.7 | DisplayString | read-only | The name of the session remote partner. Corresponds directly to the value labeled 'Destination' in the SERVER ACCOUNTING display. |
| sessionLogTable | 1.3.6.1.4.1.33.13.6.2 | not-accessible | A list of session log entries. | |
| INT sessionLogTl1AutonomousLogSize | 1.3.6.1.4.1.33.13.6.14 | INTEGER | read-write | The size in bytes of the TL1 autonomous log, which records alarms. A change in log size will not take effect until rebooting the unit. |
| INT sessionLogTl1CommandLogSize | 1.3.6.1.4.1.33.13.6.15 | INTEGER | read-write | The size in bytes of the TL1 command log, which records all TL1 commands entered on this server. A change in log size will not take effect until rebooting the unit. |
| STR sessionLogUserName | 1.3.6.1.4.1.33.13.6.2.1.6 | DisplayString | read-only | The user name logged in on the port when the event occurred. Corresponds directly to the value labeled 'Username' in the SERVER ACCOUNTING display. |
| INT sessionLogVerbose | 1.3.6.1.4.1.33.13.6.5 | INTEGER | read-write | Control for verbose logging. |
| INT sessionLogVerboseEvent | 1.3.6.1.4.1.33.13.6.2.1.12 | INTEGER | read-only | When logging in 'verbose' mode, the event that occured. |
| STR sessionLogVerboseMessage | 1.3.6.1.4.1.33.13.6.2.1.14 | DisplayString | read-only | Text describing the event that was logged. |
| OCT sessionLogX25CalledAddress | 1.3.6.1.4.1.33.13.6.2.1.16 | OCTET STRING | read-only | For an X.25 connection, the X.121 destination address. |
| OCT sessionLogX25CallerAddress | 1.3.6.1.4.1.33.13.6.2.1.15 | OCTET STRING | read-only | For an X.25 connection, the X.121 source address. |
| INT sessionLogX25Direction | 1.3.6.1.4.1.33.13.6.2.1.13 | INTEGER | read-only | The initial direction for an X.25 connection. A value of 0 is returned if the session is not X25 |
| INT sessionLogX25DisconnectCause | 1.3.6.1.4.1.33.13.6.2.1.17 | INTEGER | read-only | For a terminated X.25 connection, the standard, X.25 cause code. |
| INT sessionLogX25DisconnectDiagnostic | 1.3.6.1.4.1.33.13.6.2.1.18 | INTEGER | read-only | For a terminated X.25 connection, the standard, X.25 diagnostic code. |
| INT sessionLogZeroAccountingAll | 1.3.6.1.4.1.33.13.6.12 | INTEGER | read-write | A control to clear all entries in the accounting log including command log entries. Corresponds directly to the command CLEAR SERVER ACCOUNTING ALL. In response to a get-request or get-next-request the agent always returns ready for this value. |
| INT sessionLogZeroAlarmLogging | 1.3.6.1.4.1.33.13.6.17 | INTEGER | read-write | Control to clear all alarm log entries. In response to a get-request or a get-next-request the agent always returns ready for this value. |
| INT sessionLogZeroCommandLogging | 1.3.6.1.4.1.33.13.6.13 | INTEGER | read-write | A control to clear all command log entries. Corresponds directly to the command CLEAR SERVER COMMAND LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value. |
| INT sessionLogZeroDataLogging | 1.3.6.1.4.1.33.13.6.16 | INTEGER | read-write | A control to clear all data log entries. Corresponds directly to the command CLEAR SERVER DATA LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value. |
| NTF temperatureNormal | 1.3.6.1.4.1.33.0.44 | Indication that the temperature returned within bounds, and the value of the currrent temperature. | ||
| NTF temperatureThresholdExceeded | 1.3.6.1.4.1.33.0.38 | Indication that the temperature exceeded a threshhold and the value of the currrent temperature. | ||
| xBasic | 1.3.6.1.4.1.33.13.1 | |||
| xBroadcastGroup | 1.3.6.1.4.1.33.13.8 | |||
| xCcl | 1.3.6.1.4.1.33.13.7 | |||
| xCharacter | 1.3.6.1.4.1.33.13 | |||
| xDial | 1.3.6.1.4.1.33.13.5 | |||
| xMenu | 1.3.6.1.4.1.33.13.3 | |||
| xNetLogin | 1.3.6.1.4.1.33.13.4 | |||
| xPingHosts | 1.3.6.1.4.1.33.13.9 | |||
| xQueue | 1.3.6.1.4.1.33.13.2 | |||
| xSessionLog | 1.3.6.1.4.1.33.13.6 |
RFC description
Manages character stream devices, alarm, sensor, and power management functions on MRV In-Reach systems.
Start monitoring MRV In-Reach console/terminal server with environmental/power management with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.