Juniper-AAA-MIB

All MIBs › Juniper-AAA-MIB

Organization: Juniper Networks, Inc.

Last Updated: 2008-10-24

Category: Domain: Subscriber Management, RADIUS and AAA, Vendor: Juniper

Description: Defines managed objects for Authentication, Authorization, and Accounting (AAA) on Juniper Networks ERX/E-series broadband routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-AAA-MIB?

Juniper-AAA-MIB is a Juniper Networks enterprise MIB module defining managed objects for Authentication, Authorization, and Accounting (AAA) services on Juniper ERX/E-series broadband edge routers. It exposes configuration data covering subscriber domain and realm delimiter parsing, BRAS licensing limits, subscriber count limits, tunnel calling-number formatting, and interface identifier/adapter formatting used for subscriber sessions. Rather than raw hardware telemetry, it is used primarily to monitor and verify AAA subsystem configuration and licensing status, such as how many BRAS-licensed users are permitted versus consumed and how domain/realm name parsing is configured. It is a Juniper-proprietary enterprise MIB built around standard RADIUS/AAA concepts but does not itself extend a specific IETF MIB. It is deployed in broadband access networks where E-series routers act as a Broadband Remote Access Server (BRAS) terminating large numbers of subscriber PPP/DHCP sessions. Engineers can download the Juniper-AAA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-AAA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper ERX/E-series broadband edge routers (BRAS)

Monitoring Examples

An administrator polls juniAaaAssignBrasLicensedUsers against juniAaaAssignBrasLicense to track how close a router is to its licensed subscriber ceiling, alerting before new sessions are rejected. Objects like juniAaaAssignDomainDelimiters, juniAaaAssignRealmDelimiters, and juniAaaAssignDomainParseOrder let an operator confirm that domain-based routing of subscriber authentication requests is configured as expected. juniAaaAssignSubscriberLimit provides a hard capacity ceiling used for planning on a given router.

What Can Be Monitored

BRAS license count
licensed subscriber usage
subscriber limit
domain/realm delimiter configuration
domain parse order
tunnel calling number format

Imported Objects

From IPV6-TC

Ipv6Address
Ipv6AddressIfIdentifier
Ipv6AddressPrefix

From Juniper-MIBs

juniMibs

MODULE-IDENTITY

From Juniper-ROUTER-MIB

juniRouterIndex

OBJECT-TYPE

From Juniper-TC

JuniEnable
JuniInterfaceLocationType
JuniInterfaceLocationValue
JuniName
JuniVrfGroupName

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using juniAaaIncomingInitiateRequests OID:

Select a Juniper ERX/E-series broadband edge router (BRAS AAA) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniAaaIncomingInitiateRequests into the Find box to locate it in the OID tree, then select it and click OK. The number of AAA incoming initiate requests. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
juniAaaMIB	1.3.6.1.4.1.4874.2.2.20			The Authentication, Authorization and Accounting (AAA) MIB for the Juniper Networks enterprise.
juniAaaObjects	1.3.6.1.4.1.4874.2.2.20.1
juniAaaAssignment	1.3.6.1.4.1.4874.2.2.20.1.1
juniAaaAssignGeneral	1.3.6.1.4.1.4874.2.2.20.1.1.1
STR juniAaaAssignBrasLicense	1.3.6.1.4.1.4874.2.2.20.1.1.1.1	DisplayString	read-write	The license string that determines the system-wide maximum number of remote user connections allowed. A zero-length string (no license) prohibits remote user connections.
I32 juniAaaAssignBrasLicensedUsers	1.3.6.1.4.1.4874.2.2.20.1.1.1.2	Integer32	read-only	The system-wide maximum number of remote user connections allowed by the currently configured license string.
STR juniAaaAssignDomainDelimiters	1.3.6.1.4.1.4874.2.2.20.1.1.1.3	DisplayString	read-write	The list of delimiters used to separate the user's name from the user's domain in the username field. The default is '@'.
STR juniAaaAssignRealmDelimiters	1.3.6.1.4.1.4874.2.2.20.1.1.1.4	DisplayString	read-write	The list of delimiters used to separate the user's name from the user's realm in the username field. The realm is treated like the domain in the ERX. The default is none.
INT juniAaaAssignDomainParseOrder	1.3.6.1.4.1.4874.2.2.20.1.1.1.5	INTEGER	read-write	The order in which the user's name is parsed: either search for domain first or realm first in the form (realm/user@domain.com). The default is domain first.
I32 juniAaaAssignSubscriberLimit	1.3.6.1.4.1.4874.2.2.20.1.1.1.6	Integer32	read-write	The maximum number of subscribers permitted in this VR context. The value '0' means no limit.
U32 juniAaaAssignDomainMaxPadnPerDomain	1.3.6.1.4.1.4874.2.2.20.1.1.1.7	Unsigned32	read-only	The maximum number of PPPoE active discovery network (PADN) entries permitted in a domain entry.
INT juniAaaInterfaceIdFormat	1.3.6.1.4.1.4874.2.2.20.1.1.1.8	INTEGER	read-write	The interface ID format: include or exclude sub-interface per VR. The sub-interface is included or excluded at the time of the initial AAA request for the user and remains for the duration of the login.
INT juniAaaAssignTunnelCallingNumberFormat	1.3.6.1.4.1.4874.2.2.20.1.1.1.9	INTEGER	read-write	The format of the interface identifier passed to L2TP during an authentication request. L2TP uses this identifier as the calling-number (type 22) attribute value. Note: if selected components of the calling number format are not available (i.e. PPPoE Agent Circuit Id and Agent Remote Id), then the juniAaaAssignTunnelCallingNumberFallbackFormat will be used. Optionally the SVLAN ID inclusion can be enabled
INT juniAaaAssignDomainParseDirection	1.3.6.1.4.1.4874.2.2.20.1.1.1.10	INTEGER	read-write	The direction in which the user's name is parsed: either search for domain delimiter from left to right or right to left; first delimiter marks boundry. The default is right to left.
INT juniAaaAssignRealmParseDirection	1.3.6.1.4.1.4874.2.2.20.1.1.1.11	INTEGER	read-write	The direction in which the user's name is parsed: either search for realm delimiter from left to right or right to left; first delimiter marks boundry. The default is left to right.
INT juniAaaInterfaceAdapterFormat	1.3.6.1.4.1.4874.2.2.20.1.1.1.12	INTEGER	read-write	The interface adapter format: include or exclude the adapter if present field per VR. The adapter field is included or excluded at the time of the initial AAA request for the user and remains for the duration of the login.
INT juniAaaAssignAccountingStatisticsType	1.3.6.1.4.1.4874.2.2.20.1.1.1.13	INTEGER	read-write	The method for collecting AAA acounting statistics. When value is 'full', collect a full set of statistics for AAA accounting. When the value is 'uptime', collect only uptime value for AAA accounting.
JUN juniAaaAssignQosDownstreamRate	1.3.6.1.4.1.4874.2.2.20.1.1.1.14	JuniEnable	read-write	Enables/disables the reporting of the dsl downstream rate information to Qos.
INT juniAaaAssignTunnelCallingNumberFormatFallback	1.3.6.1.4.1.4874.2.2.20.1.1.1.15	INTEGER	read-write	The fallback format of the interface identifier passed to L2TP during an authentication request. L2TP uses this identifier as the calling-number (type 22) attribute value.
T/F juniAaaFramedIpv6PrefixAsIpv6NdRaPrefix	1.3.6.1.4.1.4874.2.2.20.1.1.1.16	TruthValue	read-write	Enables/disables the use of framed-ipv6-prefix RADIUS attribute for IPv6 ND router advertisement.
T/F juniAaaDelegatedIpv6PrefixAsDhcpv6DelegatedPrefix	1.3.6.1.4.1.4874.2.2.20.1.1.1.17	TruthValue	read-write	Enables/disables the use of delegated-ipv6-prefix RADIUS attribute for DHCPv6 prefix delegation.
juniAaaAssignDomain	1.3.6.1.4.1.4874.2.2.20.1.1.2
juniAaaAssignDomainTable	1.3.6.1.4.1.4874.2.2.20.1.1.2.1		not-accessible	The entries in this table specify the assignment of a remote access user to a virtual router, based on the user's domain.
juniAaaAssignDomainEntry	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1		not-accessible	A specification of the virtual router to which users on a specified domain should be assigned.
JUN juniAaaAssignDomainName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.1	JuniAaaDomainName	read-only	The domain name uniquely identifying this entry.
ROW juniAaaAssignDomainRowStatus	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
JUN juniAaaAssignDomainRouterName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.3	JuniName	read-only	This variable is replaced by juniAaaAssignDomainAuthRouterName and juniAaaAssignDomainIpRouterName. It returns same value as juniAaaAssignDomainAuthRouterName.
I32 juniAaaAssignDomainLoopback	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.4	Integer32	read-create	The number of the loopback interface, associated with the specified virtual router, whose IP address is used as the source address when transmitting IP packets on unnumbered remote access user links. For example, if the associated loopback interface for this domain/router was configured via the console as 'loopback 2', this object would contain the integer value 2. A value of -1 indicates the loopback interface is unspecified.
T/F juniAaaAssignDomainIpHint	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.5	TruthValue	read-create	Enables/disables the IP hint feature, which causes the system to allocate an IP address before going to RADIUS for authentication.
INT juniAaaAssignDomainAtmServiceLevel	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.6	INTEGER	read-create	The Service category for this circuit: ubr Unspecified bit rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-realtime Variable Bit Rate. cbr Constant bit rate. rtVbr Realtime Variable Bit Rate. Set the service level in combination of the traffic attributes PCR/SCR/MBS in the following matrix for successfull configurations. ServiceLevel PCR SCR MBS ------------------------------------------ ubr omit omit omit ubrPcr must omit omit nrtVbr must must must cbr must omit omit rtVbr must must must
U32 juniAaaAssignDomainAtmPcr	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.7	Unsigned32	read-create	Peak Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAaaAssignDomainAtmServiceLevel is configured to have one of the following values: ubrPcr nrtVbr cbr
U32 juniAaaAssignDomainAtmScr	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.8	Unsigned32	read-create	Sustained Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAaaAssignDomainAtmServiceLevel is configured to have one of the following values: nrtVbr
U32 juniAaaAssignDomainAtmMbs	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.9	Unsigned32	read-create	Maximum Burst Size, in cells, of this circuit. This parameter is only required when juniAaaAssugbDomainAtmServiceLevel is configured to have one of the following values: nrtVbr
STR juniAaaAssignDomainOverrideUserName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.10	DisplayString	read-create	The override user name associated with this entry. This object is used to override the user name of the remote client.
OCT juniAaaAssignDomainOverridePassword	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.11	OCTET STRING	read-create	The override password for the user name defined by juniAaaAssignDomainOverrideUserName. This object is used to override the password part of the username/password pair of the remote client. This value returns a string length of 0 on reads for security reasons.
T/F juniAaaAssignDomainStripDomain	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.12	TruthValue	read-create	Enables/disables the domain name stripping feature, which causes the system to strip the domain name before sending the access-request to RADIUS for authentication.
STR juniAaaAssignDomainPoolName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.13	DisplayString	read-create	The name of the local address pool from which to allocate an IP address for the subscriber when none is returned from the authentication server.
STR juniAaaAssignDomainLocalInterface	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.14	DisplayString	read-create	The local interface, associated with the specified virtual router, whose IP address is used as the source address when transmitting IP packets on remote access user links.
JUN juniAaaAssignDomainIpv6RouterName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.15	JuniName	read-create	The name of the virtual router to which remote access users within this domain are assigned for IPv6 interfaces.
STR juniAaaAssignDomainIpv6LocalInterface	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.16	DisplayString	read-create	The local interface, associated with the specified virtual router, whose IPv6 address is used as the source address when transmitting IPv6 packets on remote access user links.
JUN juniAaaAssignDomainTunnelGroup	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.17	JuniAaaTunnelGroupName	read-create	The tunnel group assigned to this domain map. Non default configuration of this object cannot coexist with matching tunnel entries in juniAaaAssignDomainTunnelTable.
JUN juniAaaAssignDomainAuthRouterName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.18	JuniName	read-create	The name of the virtual router where remote access users within this domain will be authenticated.
JUN juniAaaAssignDomainIpRouterName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.19	JuniName	read-create	The name of the virtual router to which remote access users within this domain are assigned for IP interfaces.
T/F juniAaaAssignDomainTunnelSubscriberAuthentication	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.20	TruthValue	read-create	When there are tunnel configurations under this domain, enable or disable subscribers of this domain authenticate with configured authentication server.
STR juniAaaAssignDomainBackupPoolName	1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.21	DisplayString	read-create	The name of the backup local address pool from which to allocate an IP address for the subscriber when the primary address pool is 100% allocated
juniAaaAssignDomainTunnelTable	1.3.6.1.4.1.4874.2.2.20.1.1.2.2		not-accessible	The entries in this table specify the tunnels associated with a domain.
juniAaaAssignDomainTunnelEntry	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1		not-accessible	A specification of the tunnels associated with a domain.
JUN juniAaaAssignDomainTunnelName	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.1	JuniAaaDomainName	read-only	The domain name associated with this entry.
I32 juniAaaAssignDomainTunnelTag	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.2	Integer32	read-only	The tunnel tag value associated with this entry.
I32 juniAaaAssignDomainTunnelPreference	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.3	Integer32	read-create	The tunnel's preference value associated with this entry. The value 0 is the highest preference.
INT juniAaaAssignDomainTunnelType	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.4	INTEGER	read-create	The tunnel type associated with this entry. Attempts to set this object to tunnelUnknown(2) and tunnelL2f(3) will fail (wrongValue).
INT juniAaaAssignDomainTunnelMedium	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.5	INTEGER	read-create	The tunnel medium associated with this entry. The medium dictates the format of the tunnel address. Attempts to set this object to tunnelMediumUnknown(2) will fail (wrongValue).
STR juniAaaAssignDomainTunnelAddress	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.6	DisplayString	read-create	The tunnel server address associated with this entry. The juniAaaAssignDomainTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
STR juniAaaAssignDomainTunnelPassword	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.7	DisplayString	read-create	The tunnel password associated with this entry. The object returns a null length string on reads due to security concerns.
STR juniAaaAssignDomainTunnelId	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.8	DisplayString	read-create	The tunnel identifier associated with this entry. The tunnel identifier is used to distinguish between multiple tunnels to the same juniAaaAssignDomainTunnelAddress.
STR juniAaaAssignDomainTunnelHostName	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.9	DisplayString	read-create	The tunnel client hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Client-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
ROW juniAaaAssignDomainTunnelRowStatus	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.10	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
STR juniAaaAssignDomainTunnelServerName	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.11	DisplayString	read-create	The tunnel server hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Server-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
STR juniAaaAssignDomainTunnelClientAddress	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.12	DisplayString	read-create	The tunnel client address associated with this entry. The juniAaaAssignDomainTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
U32 juniAaaAssignDomainTunnelMaxSessions	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.13	Unsigned32	read-create	The tunnel's max-session value associated with this entry. The value 0 indicates no maximum session value.
I32 juniAaaAssignDomainTunnelReceiveWindowSize	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.14	Integer32	read-create	For an L2TP tunnel this object represents the receive window size. A value of 0 indicates that this object has no effect on the tunnel's receive window size.
INT juniAaaAssignDomainTunnelFailoverResync	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.15	INTEGER	read-create	For an L2TP tunnel this object represents the failover resync mechanism: disable(0) - Disable failover resync failoverProtocol(1) - Use the L2TP Failover Protocol silentFailover(2) - Use the JUNOSe Silent Failover Mechanism failoverProtocolFallbackToSilentFailover(3) - (Default) Use the L2TP Failover Protocol and fall back to Silent Failover.
JUN juniAaaAssignDomainTunnelSwitchProfile	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.16	JuniAaaTunnelSwitchProfileName	read-create	The name of the L2TP tunnel switch profile to apply in tunnel switching scenarios.
INT juniAaaAssignDomainTunnelTxConnectSpeedMethod	1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.17	INTEGER	read-create	For an L2TP tunnel this object represents the tx connect speed method mechanism at the LAC: notSet(0) - this parameter has not been configured staticLayer2(1) - use static layer 2 settings dynamicLayer2(2) - use layer 2 settings including dynamic speeds qos(3) - use qos speed actual(4) - minimum of dynamicLayer2 and qos
juniAaaAssignDomainPadnTable	1.3.6.1.4.1.4874.2.2.20.1.1.2.3		not-accessible	The entries in this table specify the PPPoE active discovery network (PADN) parameters associated with a domain.
juniAaaAssignDomainPadnEntry	1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1		not-accessible	A specification of the PPPoE active discovery network parameters associated with a domain.
IP juniAaaAssignDomainPadnIpAddress	1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.1	IpAddress	not-accessible	The IP address of this entry.
IP juniAaaAssignDomainPadnIpMask	1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.2	IpAddress	not-accessible	The IP mask of this entry.
ROW juniAaaAssignDomainPadnRowStatus	1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.3	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
I32 juniAaaAssignDomainPadnDistance	1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.4	Integer32	read-create	The administrative distance metric of this entry.
juniAaaAuthentication	1.3.6.1.4.1.4874.2.2.20.1.2
juniAaaAuthGeneral	1.3.6.1.4.1.4874.2.2.20.1.2.1
OCT juniAaaAuthMethods	1.3.6.1.4.1.4874.2.2.20.1.2.1.1	OCTET STRING	read-write	The set of authentication protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAuthenticationMethods TEXTUAL-CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding authentication protocol defined by JuniAaaAuthenticationMethods. Note that if the octet is set to: protocolNone(4) Then authentication does not take place. If an authentication protocol is configured and attempts to reach the authentication server fail, the system will move to the next octet in this object and retry the authentication in the form dictated by the corresponding authentication protocoltype. The process of sequencing thru each octet will stop if the authentication server is successfully contacted, or there are no more configured octets in this object.
juniAaaAuthMethodsTable	1.3.6.1.4.1.4874.2.2.20.1.2.1.2		not-accessible	The entries in this table specify the assignment of authentication methods for a particular subscriber type.
juniAaaAuthMethodsEntry	1.3.6.1.4.1.4874.2.2.20.1.2.1.2.1		not-accessible	A specification of the authentication methods for a particular subscriber type.
JUN juniAaaAuthMethodsSubscriberType	1.3.6.1.4.1.4874.2.2.20.1.2.1.2.1.1	JuniAaaAuthenticationSubscriberTypes	read-only	The subscriber type.
OCT juniAaaAuthMethodsAuthentication	1.3.6.1.4.1.4874.2.2.20.1.2.1.2.1.2	OCTET STRING	read-write	The set of authentication protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAuthenticationMethods TEXTUAL-CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding authentication protocol defined by JuniAaaAuthenticationMethods. Note that if the octet is set to: protocolNone(4) Then authentication does not take place. If an authentication protocol is configured and attempts to reach the authentication server fail, the system will move to the next octet in this object and retry the authentication in the form dictated by the corresponding authentication protocoltype. The process of sequencing thru each octet will stop if the authentication server is successfully contacted, or there are no more configured octets in this object.
juniAaaLocalAuth	1.3.6.1.4.1.4874.2.2.20.1.2.2
juniAaaLocalAuthUser	1.3.6.1.4.1.4874.2.2.20.1.2.2.1
juniAaaLocalAuthUserTable	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1		not-accessible	This table contains entries for users present in the local user databases.
juniAaaLocalAuthUserEntry	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1		not-accessible	Each entry in this table represents a single user in a local user database.
STR juniAaaLocalAuthUserName	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.1	DisplayString	not-accessible	The name of the user.
ROW juniAaaLocalAuthUserRowStatus	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported.
OCT juniAaaLocalAuthUserPassword	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.3	OCTET STRING	read-create	The password for this user. If the juniAaaLocalAuthUserEncrypted object is not set with this object, the password value is assumed to be unencrypted. When set, any existing password is overwritten. Setting a zero length OCTET STRING removes the password. Reading this object always results in a zero length OCTET STRING.
INT juniAaaLocalAuthUserEncryption	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.4	INTEGER	read-create	The encryption type of the password value being set with the juniAaaLocalAuthUserPassword object. Reading this object always results in a value of encryptionNone. encyptionNone - The password is unencrypted (i.e. in plain text.) encyptionSecret - The password has been generated using a one-way MD5 encryption mechanism, algorithm 5. encyptionPassword - The password has been generated using a two-way encryption mechanism, algorithm 8.
IP juniAaaLocalAuthUserIpAddress	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.5	IpAddress	read-create	The IP address this user is to be assigned, once authenticated. This object corresponds to the Framed-IP-Address attribute in RADIUS authentication servers.
STR juniAaaLocalAuthUserIpAddressPool	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.6	DisplayString	read-create	The name of the local address pool this user is to be allocated an IP address from, once authenticated. This object corresponds to the Framed-Pool attribute in RADIUS authentication servers.
JUN juniAaaLocalAuthUserRouterName	1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.7	JuniName	read-create	The name of the router this user is to be assigned to, once authenticated. This object corresponds to the Unispher-Virtual-Router attribute in RADIUS authentication servers.
juniAaaLocalAuthUserDb	1.3.6.1.4.1.4874.2.2.20.1.2.2.2
juniAaaLocalAuthUserDbTable	1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1		not-accessible	This table contains entries for local user databases.
juniAaaLocalAuthUserDbEntry	1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1.1		not-accessible	Each entry in this table represents a single local user database.
STR juniAaaLocalAuthUserDbName	1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1.1.1	DisplayString	not-accessible	The name of this local user database.
ROW juniAaaLocalAuthUserDbRowStatus	1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported.
juniAaaLocalAuthUserDbAssoc	1.3.6.1.4.1.4874.2.2.20.1.2.2.3
juniAaaLocalAuthUserDbAssocTable	1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1		not-accessible	This table contains entries that identify the local user database that is associated with each virtual router.
juniAaaLocalAuthUserDbAssocEntry	1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1.1		not-accessible	Each entry in this table represents a single association between a virtual router and local user database. The same database can be referenced by multiple virtual routers; however, a virtual router can reference only one database. No entries are displayed for virtual routers that reference the default local user database.
ROW juniAaaLocalAuthUserDbAssocRowStatus	1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1.1.1	RowStatus	read-create	Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported. When a virtual router is deleted, its corresponding entries in this table will be deleted as well.
STR juniAaaLocalAuthUserDbAssocDbName	1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1.1.2	DisplayString	read-create	The name of local user database associated with this virtual router. Setting the name to the default local user database, 'default', will delete this entry, as this is the default association for all virtual routers.
juniAaaAccounting	1.3.6.1.4.1.4874.2.2.20.1.3
juniAaaAcctGeneral	1.3.6.1.4.1.4874.2.2.20.1.3.1
I32 juniAaaAcctInterval	1.3.6.1.4.1.4874.2.2.20.1.3.1.1	Integer32	read-write	The interval that must elapse between generation of accounting reports, ranging from 10 minutes to 24 hours, or disabled if set to zero. The set of this object affects both the juniAaaServiceAcctInterval and juniAaaUserAcctInterval values; the get of this object returns only the juniAaaUserAcctInterval value.
JUN juniAaaAcctDupServerRouterName	1.3.6.1.4.1.4874.2.2.20.1.3.1.2	JuniName	read-write	The name of another router on this system to which accounting reports should be sent, in addition to or instead of sending accounting reports to the accounting service (if any) configured on the current router (i.e., the router context within which this object instance exists). A zero-length name disables this mechanism.
OCT juniAaaAcctMethods	1.3.6.1.4.1.4874.2.2.20.1.3.1.3	OCTET STRING	read-write	The set of accounting protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAccountingMethods TEXTUAL CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding accounting protocol defined by JuniAaaAccountingMethods. Note that if the octet is set to: protocolNone(4) Then accounting is disabled. If an accounting protocol is configured and reports are not successfully generated, the system will move to the next octet in this object and repeat the attempt to generate an accounting report in the form dictated by the corresponding accounting protocol type. The process of sequencing thru each octet will stop if accounting reports are either successfully generated, or there are no more configured octets in this object.
T/F juniAaaAcctSendStopOnAaaDeny	1.3.6.1.4.1.4874.2.2.20.1.3.1.4	TruthValue	read-write	Enables/disables the accounting stop message sent to the accounting server when authentication server grants access, but AAA denies access.
T/F juniAaaAcctSendStopOnAaaReject	1.3.6.1.4.1.4874.2.2.20.1.3.1.5	TruthValue	read-write	Enables/disables the accounting stop message sent to the accounting server when authentication server denies access.
T/F juniAaaAcctSendImmediateAcctUpdate	1.3.6.1.4.1.4874.2.2.20.1.3.1.6	TruthValue	read-write	Enables/disables the sending of an accounting update with the client's IP address upon receipt of accounting start response.
juniAaaAcctMethodsTable	1.3.6.1.4.1.4874.2.2.20.1.3.1.7		not-accessible	The entries in this table specify the assignment of accounting methods for a particular subscriber type.
juniAaaAcctMethodsEntry	1.3.6.1.4.1.4874.2.2.20.1.3.1.7.1		not-accessible	A specification of the accounting methods for a particular subscriber type.
JUN juniAaaAcctMethodsSubscriberType	1.3.6.1.4.1.4874.2.2.20.1.3.1.7.1.1	JuniAaaAccountingSubscriberTypes	read-only	The subscriber type.
OCT juniAaaAcctMethodsAccounting	1.3.6.1.4.1.4874.2.2.20.1.3.1.7.1.2	OCTET STRING	read-write	The set of accounting protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAccountingMethods TEXTUAL CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding accounting protocol defined by JuniAaaAccountingMethods. Note that if the octet is set to: protocolNone(4) Then accounting is disabled. If an accounting protocol is configured and reports are not successfully generated, the system will move to the next octet in this object and repeat the attempt to generate an accounting report in the form dictated by the corresponding accounting protocol type. The process of sequencing thru each octet will stop if accounting reports are either successfully generated, or there are no more configured octets in this object.
JUN juniAaaAcctBcastServerGroupName	1.3.6.1.4.1.4874.2.2.20.1.3.1.8	JuniVrfGroupName	read-write	The name of a group of other routers on this system to which accounting reports should be sent, for every subsriber who has this router assigned as an operational router. A zero-length name disables this mechanism.
I32 juniAaaUserAcctInterval	1.3.6.1.4.1.4874.2.2.20.1.3.1.9	Integer32	read-write	The interval that must elapse between generation of user accounting reports, ranging from 10 minutes to 24 hours, or disabled if set to zero.
I32 juniAaaServiceAcctInterval	1.3.6.1.4.1.4874.2.2.20.1.3.1.10	Integer32	read-write	The interval that must elapse between generation of service accounting reports, ranging from 10 minutes to 24 hours, or disabled if set to zero.
juniAaaAcctBcastConfig	1.3.6.1.4.1.4874.2.2.20.1.3.2
juniAaaAcctBcastServerGroupTable	1.3.6.1.4.1.4874.2.2.20.1.3.2.1		not-accessible	The entries in this table specify broadcast accounting routers of the named group. In addition to row status operations if juniAaaAcctBrasServerGroupRouter1, juniAaaAcctBrasServerGroupRouter2, juniAaaAcctBrasServerGroupRouter3 and juniAaaAcctBrasServerGroupRouter4 are all set zero length strings, the entry will be deleted. At least one non zero length string router is required to successfully create and entry. All non zero length string routers have to be unique within the group.
juniAaaAcctBcastServerGroupEntry	1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1		not-accessible	A specification of the accounting servers for a particular group.
JUN juniAaaAcctBcastServerGroup	1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.1	JuniVrfGroupName	not-accessible	The group name.
JUN juniAaaAcctBcastServerGroupRouter1	1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.2	JuniName	read-write	The name of the first router in the group.
JUN juniAaaAcctBcastServerGroupRouter2	1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.3	JuniName	read-write	The name of the second router in the group.
JUN juniAaaAcctBcastServerGroupRouter3	1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.4	JuniName	read-write	The name of the third router in the group.
JUN juniAaaAcctBcastServerGroupRouter4	1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.5	JuniName	read-write	The name of the third router in the group.
ROW juniAaaAcctBcastServerGroupRowStatus	1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.6	RowStatus	read-write	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET. In addition to row status operations if juniAaaAcctBrasServerGroupRouter1, juniAaaAcctBrasServerGroupRouter2, juniAaaAcctBrasServerGroupRouter3 and juniAaaAcctBrasServerGroupRouter4 are all set zero length strings, the entry will be deleted. At least one non zero length string router is required to successfully create and entry.
juniAaaAddress	1.3.6.1.4.1.4874.2.2.20.1.4
juniAaaAddrGeneral	1.3.6.1.4.1.4874.2.2.20.1.4.1
INT juniAaaAddrPoolDefault	1.3.6.1.4.1.4874.2.2.20.1.4.1.1	INTEGER	read-write	Identifies the default source of IP address allocation for remote access links: none No address source is specified. Using this setting allows the remote PPP subscriber (client) to set it's own address. local Use the local address pool named 'default'. dhcp Use DHCP service.
T/F juniAaaDupAddrCheck	1.3.6.1.4.1.4874.2.2.20.1.4.1.2	TruthValue	read-write	Enables/disables the duplicate IP address checking which causes the system to check the route table for the PPP user's dynamic IP address is provided to PPP (from AAA).
juniAaaAddrNameServer	1.3.6.1.4.1.4874.2.2.20.1.4.2
juniAaaAddrDns	1.3.6.1.4.1.4874.2.2.20.1.4.2.1
IP juniAaaAddrDnsPrimary	1.3.6.1.4.1.4874.2.2.20.1.4.2.1.1	IpAddress	read-write	The IP address of the primary DNS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
IP juniAaaAddrDnsSecondary	1.3.6.1.4.1.4874.2.2.20.1.4.2.1.2	IpAddress	read-write	The IP address of the secondary DNS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
ADR juniAaaAddrIpv6DnsPrimary	1.3.6.1.4.1.4874.2.2.20.1.4.2.1.3	Ipv6Address	read-write	The IPv6 address of the primary IPv6 DNS server to be used by remote access clients. A value of ::0 indicates no server is configured.
ADR juniAaaAddrIpv6DnsSecondary	1.3.6.1.4.1.4874.2.2.20.1.4.2.1.4	Ipv6Address	read-write	The IPv6 address of the secondary IPv6 DNS server to be used by remote access clients. A value of ::0 indicates no server is configured.
juniAaaAddrWins	1.3.6.1.4.1.4874.2.2.20.1.4.2.2
IP juniAaaAddrWinsPrimary	1.3.6.1.4.1.4874.2.2.20.1.4.2.2.1	IpAddress	read-write	The IP address of the primary WINS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
IP juniAaaAddrWinsSecondary	1.3.6.1.4.1.4874.2.2.20.1.4.2.2.2	IpAddress	read-write	The IP address of the secondary WINS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
juniAaaStatistics	1.3.6.1.4.1.4874.2.2.20.1.5
C32 juniAaaIncomingInitiateRequestsEx	1.3.6.1.4.1.4874.2.2.20.1.5.1	Counter32	read-only	The number of AAA incoming initiate requests
C32 juniAaaIncomingTerminateRequests	1.3.6.1.4.1.4874.2.2.20.1.5.2	Counter32	read-only	The number of AAA incomining termination requests
C32 juniAaaOutgoingTunnelGrantResponses	1.3.6.1.4.1.4874.2.2.20.1.5.3	Counter32	read-only	The number of AAA outgoing tunnel grant responses
C32 juniAaaOutgoingGrantResponses	1.3.6.1.4.1.4874.2.2.20.1.5.4	Counter32	read-only	The number of AAA outgoing grant responses
C32 juniAaaOutgoingDenyResponses	1.3.6.1.4.1.4874.2.2.20.1.5.5	Counter32	read-only	The number of AAA outgoing deny responses
C32 juniAaaOutgoingErrorResponses	1.3.6.1.4.1.4874.2.2.20.1.5.6	Counter32	read-only	The number of AAA outgoing error responses
C32 juniAaaOutgoingAuthRequests	1.3.6.1.4.1.4874.2.2.20.1.5.7	Counter32	read-only	The number of AAA outgoing authentication requests
C32 juniAaaIncomingAuthResponses	1.3.6.1.4.1.4874.2.2.20.1.5.8	Counter32	read-only	The number of AAA incoming authentication responses
C32 juniAaaOutgoingReAuthRequests	1.3.6.1.4.1.4874.2.2.20.1.5.9	Counter32	read-only	The number of AAA outgoing re-authentication requests
C32 juniAaaIncomingReAuthResponses	1.3.6.1.4.1.4874.2.2.20.1.5.10	Counter32	read-only	The number of AAA incoming re-authentication responses
C32 juniAaaOutgoingAcctRequests	1.3.6.1.4.1.4874.2.2.20.1.5.11	Counter32	read-only	The number of AAA outgoing accounting requests
C32 juniAaaIncomingAcctResponses	1.3.6.1.4.1.4874.2.2.20.1.5.12	Counter32	read-only	The number of AAA incoming accounting responses
C32 juniAaaOutgoingDupAcctRequests	1.3.6.1.4.1.4874.2.2.20.1.5.13	Counter32	read-only	The number of AAA outgoing duplicate accounting requests
C32 juniAaaIncomingDupAcctResponses	1.3.6.1.4.1.4874.2.2.20.1.5.14	Counter32	read-only	The number of AAA incoing duplication accounting responses
C32 juniAaaOutgoingAddrRequests	1.3.6.1.4.1.4874.2.2.20.1.5.15	Counter32	read-only	The number of AAA outgoing address requests
C32 juniAaaIncomingAddrResponses	1.3.6.1.4.1.4874.2.2.20.1.5.16	Counter32	read-only	The number of AAA incoming address responses
C32 juniAaaOutgoingBcastAcctRequests	1.3.6.1.4.1.4874.2.2.20.1.5.17	Counter32	read-only	The number of AAA outgoing broadcast accounting requests
C32 juniAaaIncomingBcastAcctResponses	1.3.6.1.4.1.4874.2.2.20.1.5.18	Counter32	read-only	The number of AAA incoing broadcast accounting responses
juniAaaTimeout	1.3.6.1.4.1.4874.2.2.20.1.6
juniAaaTimeoutGeneral	1.3.6.1.4.1.4874.2.2.20.1.6.1
I32 juniAaaIdleTimeout	1.3.6.1.4.1.4874.2.2.20.1.6.1.1	Integer32	read-write	The maximum number of seconds that a user session can be idle before system disconnects the user, ranging from 300 to 86400 seconds, 0 disables idle timeout.
I32 juniAaaSessionTimeout	1.3.6.1.4.1.4874.2.2.20.1.6.1.2	Integer32	read-write	The maximum number of seconds that a user session can be established before system disconnects the user, ranging from 60 to 31622400 seconds. 0 specifies that a default value should be used, according to the rules of the implementing interface.
JUN juniAaaMonitorIngressTrafficOnly	1.3.6.1.4.1.4874.2.2.20.1.6.1.3	JuniEnable	read-write	Enables/disables the monitoring of ingress traffic. Inactive sessions are disconnected after a period, specified in juniAaaIdleTimeout. Inactivity is determined by both inbound and outbound traffic. If this option is enabled, only ingress traffic is monitored for determining session inactivity.
juniAaaTunnel	1.3.6.1.4.1.4874.2.2.20.1.7
juniAaaTunnelGeneral	1.3.6.1.4.1.4874.2.2.20.1.7.1
STR juniAaaTunnelClientName	1.3.6.1.4.1.4874.2.2.20.1.7.1.1	DisplayString	read-write	The default tunnel client hostname associated with this virtual router. This object is used when no tunnel client name (client auth ID) is supplied in the authentication response.
STR juniAaaTunnelPassword	1.3.6.1.4.1.4874.2.2.20.1.7.1.2	DisplayString	read-write	The default tunnel password associated with this virtual router. This object is used when no tunnel password is supplied in the authentication response. The object returns a null length string on reads due to security concerns.
INT juniAaaTunnelNasPortMethod	1.3.6.1.4.1.4874.2.2.20.1.7.1.3	INTEGER	read-write	The default tunnel NAS-port method associated with this virtual router. This object is used to specify the LAC's NAS-port method. This provides limit compatiability to Cisco LNS for the NAS-port method AVP.
T/F juniAaaTunnelIgnoreNasPort	1.3.6.1.4.1.4874.2.2.20.1.7.1.4	TruthValue	read-write	Enables/disables the use of the NAS-port value that is passed in from the tunnel application.
T/F juniAaaTunnelIgnoreNasPortType	1.3.6.1.4.1.4874.2.2.20.1.7.1.5	TruthValue	read-write	Enables/disables the use of the NAS-port-type value that is passed in from the tunnel application.
INT juniAaaTunnelAssignmentIdFormat	1.3.6.1.4.1.4874.2.2.20.1.7.1.6	INTEGER	read-write	The tunnel assignment ID format for distinguishing tunnel definitions. This object is used to specify the tunnel assigment ID format passed to the LAC. The value assignmentId(0) indicates that the original tunnel assignment ID value is to be used; clientServerId(1) indicates that the concatenated value from client-auth-name, server-auth-name, and assignment-id is to be used.
JUN juniAaaTunnelSwitchProfile	1.3.6.1.4.1.4874.2.2.20.1.7.1.7	JuniAaaTunnelSwitchProfileName	read-write	The default tunnel switch profile associated with this virtual router. This object is used when no tunnel switch profile is supplied in the authentication response.
INT juniAaaTunnelTxConnectSpeedMethod	1.3.6.1.4.1.4874.2.2.20.1.7.1.8	INTEGER	read-write	The default tunnel tx connect speed method associated with this virtual router. This object is used to specify the LAC's tx connect speed method.
juniAaaTunnelGroups	1.3.6.1.4.1.4874.2.2.20.1.7.2
juniAaaTunnelGroupTable	1.3.6.1.4.1.4874.2.2.20.1.7.2.1		not-accessible	The entries in this table specify tunnel attributes sufficient tunnel establishment.
juniAaaTunnelGroupEntry	1.3.6.1.4.1.4874.2.2.20.1.7.2.1.1		not-accessible	An entry in the tunnel group table.
JUN juniAaaTunnelGroupName	1.3.6.1.4.1.4874.2.2.20.1.7.2.1.1.1	JuniAaaTunnelGroupName	read-only	The tunnel group name uniquely identifying this entry.
ROW juniAaaTunnelGroupRowStatus	1.3.6.1.4.1.4874.2.2.20.1.7.2.1.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
juniAaaTunnelGroupTunnelTable	1.3.6.1.4.1.4874.2.2.20.1.7.2.2		not-accessible	The entries in this table specify the tunnels associated with a tunnel group.
juniAaaTunnelGroupTunnelEntry	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1		not-accessible	A specification of the tunnels associated with a tunnel group.
JUN juniAaaTunnelGroupTunnelName	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.1	JuniAaaTunnelGroupName	read-only	The tunnel group name associated with this entry.
I32 juniAaaTunnelGroupTunnelTag	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.2	Integer32	read-only	The tunnel tag value associated with this entry.
I32 juniAaaTunnelGroupTunnelPreference	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.3	Integer32	read-create	The tunnel's preference value associated with this entry. The value 0 is the highest preference.
INT juniAaaTunnelGroupTunnelType	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.4	INTEGER	read-create	The tunnel type associated with this entry.
INT juniAaaTunnelGroupTunnelMedium	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.5	INTEGER	read-create	The tunnel medium associated with this entry. The medium dictates the format of the tunnel address. Attempts to set this object to tunnelMediumUnknown(2) will fail (wrongValue).
STR juniAaaTunnelGroupTunnelAddress	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.6	DisplayString	read-create	The tunnel server address associated with this entry. The juniAaaTunnelGroupTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
STR juniAaaTunnelGroupTunnelPassword	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.7	DisplayString	read-create	The tunnel password associated with this entry. The object returns a null length string on reads due to security concerns.
STR juniAaaTunnelGroupTunnelId	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.8	DisplayString	read-create	The tunnel identifier associated with this entry. The tunnel identifier is used to distinguish between multiple tunnels to the same juniAaaTunnelGroupTunnelAddress.
STR juniAaaTunnelGroupTunnelHostName	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.9	DisplayString	read-create	The tunnel client hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Client-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
ROW juniAaaTunnelGroupTunnelRowStatus	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.10	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
STR juniAaaTunnelGroupTunnelServerName	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.11	DisplayString	read-create	The tunnel server hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Server-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
STR juniAaaTunnelGroupTunnelClientAddress	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.12	DisplayString	read-create	The tunnel client address associated with this entry. The juniAaaTunnelGroupTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
I32 juniAaaTunnelGroupTunnelMaxSessions	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.13	Integer32	read-create	The tunnel's max-session value associated with this entry. The value 0 indicates no maximum session value.
I32 juniAaaTunnelGroupTunnelReceiveWindowSize	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.14	Integer32	read-create	For an L2TP tunnel this object represents the receive window size. A value of 0 indicates that this object has no effect on the tunnel's receive window size.
JUN juniAaaTunnelGroupTunnelRouterName	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.15	JuniName	read-create	The name of the virtual router to which remote access users within this tunnel are assigned.
INT juniAaaTunnelGroupTunnelFailoverResync	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.16	INTEGER	read-create	For an L2TP tunnel this object represents the failover resync mechanism: disable(0) - Disable failover resync failoverProtocol(1) - Use the L2TP Failover Protocol silentFailover(2) - Use the JUNOSe Silent Failover Mechanism failoverProtocolFallbackToSilentFailover(3) - (Default) Use the L2TP Failover Protocol and fall back to Silent Failover.
JUN juniAaaTunnelGroupTunnelSwitchProfile	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.17	JuniAaaTunnelSwitchProfileName	read-create	The name of the L2TP tunnel switch profile to apply in tunnel switching scenarios.
INT juniAaaTunnelGroupTunnelTxConnectSpeedMethod	1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.18	INTEGER	read-create	For an L2TP tunnel this object represents the tx connect speed method mechanism at the LAC: notSet(0) - this parameter has not been configured staticLayer2(1) - use static layer 2 settings dynamicLayer2(2) - use layer 2 settings including dynamic speeds qos(3) - use qos speed actual(4) - minimum of dynamicLayer2 and qos
juniAaaSubscribers	1.3.6.1.4.1.4874.2.2.20.1.8
I32 juniAaaSubscriberMaxCount	1.3.6.1.4.1.4874.2.2.20.1.8.1	Integer32	read-only	The configuration setting for the maximum number of subscribers. There is a grace number of subscribers above this limit, which when reached will cause authentication requests to be denied.
G32 juniAaaSubscriberPeakCount	1.3.6.1.4.1.4874.2.2.20.1.8.2	Gauge32	read-only	The peak number of subscribers. The peak count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated.
G32 juniAaaSubscriberCount	1.3.6.1.4.1.4874.2.2.20.1.8.3	Gauge32	read-only	The current number of subscribers. The subscriber count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated.
juniAaaSubscriberTable	1.3.6.1.4.1.4874.2.2.20.1.8.4		not-accessible	The entries in this table represent subscribers by subscriber handle value.
juniAaaSubscriberEntry	1.3.6.1.4.1.4874.2.2.20.1.8.4.1		not-accessible	A specification of subscribers by subscriber handle.
U32 juniAaaSubscriberHandle	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.1	Unsigned32	not-accessible	The subscriber handle associated with this subscriber. A subscriber handle is a monotomically increasing integer.
STR juniAaaSubscriberUserName	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.2	DisplayString	read-only	The RADIUS userName associated with this subscriber.
JUN juniAaaSubscriberRouterName	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.3	JuniName	read-only	The virtual router assigned to this subscriber.
U32 juniAaaSubscriberRouterIndex	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.4	Unsigned32	read-only	The router index that identifies the virtual router associated with this subscriber. The value of this object can be used to index the router in the juniRouterTable.
STR juniAaaSubscriberLoginTime	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.5	DisplayString	read-only	The time this subscriber logged in to RADIUS server.
IP juniAaaSubscriberIpAddress	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.6	IpAddress	read-only	The client IP Address assigned to this subscriber.
IP juniAaaSubscriberIpAddressMask	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.7	IpAddress	read-only	The client IP Address Mask assigned to this subscriber.
ADR juniAaaSubscriberAddrAssignType	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.8	JuniAddressAssignType	read-only	The address assignment type for this subscriber.
STR juniAaaSubscriberInterfaceId	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.9	DisplayString	read-only	A text string describing the local interface associated with this subscriber. Types/formats/examples for this string include: ERX: == /; E320: == //; ATM Virtual Circuit atm :. 'atm 3/2:0.100' (ERX) 'atm 3/0/2:0.100' (E320) Ethernet { fastEthernet \| gigabitEthernet } 'fastEthernet 3/2' (ERX) 'gigabitEthernet 3/2' (ERX) 'gigabitEthernet 3/0/2' (E320) 'tenGigabitEthernet 3/0/2' (E320) Ethernet VLAN { fastEthernet \| gigabitEthernet } : 'fastEthernet 3/2:1000' (ERX) 'gigabitEthernet 3/2:1000' (ERX) 'gigabitEthernet 3/0/2:1000' (E320) 'tenGigabitEthernet 3/0/2:1000' (E320) Channelized Serial serial :[/]* 'serial 3/2:4' (ERX T1/E1) 'serial 3/2:2/4' (ERX T3/E3) 'serial 3/2:2/1/1/4' (ERX OC3/OC12 - channelized DS3) 'serial 3/2:2/1/1/1/4' (ERX OC3/OC12 - virtual tributaries) 'serial 3/0/2:2/1/1/4' (E320 OC3/OC12 - channelized DS3) 'serial 3/0/2:2/1/1/1/4' (E320 OC3/OC12 - virtual tributaries) L2TP over IP ip::::: :: 'ip:10.10.0.1:20.20.0.2:1234:5678:9abc:def0:6789abcd' (Note: tunnelIDs, sessionIDs, and callSerialNumber are in hexadecimal.) Other formats may be supported over time.
JUN juniAaaSubscriberState	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.10	JuniSubscriberState	read-only	The state of this subscriber.
JUN juniAaaSubscriberClientType	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.11	JuniSubscriberClientType	read-only	The client type for this subscriber. Certain client types (e.g., 'other') might be suppressed from representation in this table.
STR juniAaaSubscriberIngressPolicyName	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.12	DisplayString	read-only	The Ingress Policy Name associated with this subscriber.
STR juniAaaSubscriberEgressPolicyName	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.13	DisplayString	read-only	The Egress Policy Name associated with this subscriber.
STR juniAaaSubscriberQosProfileName	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.14	DisplayString	read-only	The QoS Profile Name associated with this subscriber.
ROW juniAaaSubscriberRowStatus	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.15	RowStatus	read-write	Controls the deletion of the subscriber from this table. Deletion of the subscriber is analogous to logging the subscriber out of the network. Note: only 'destroy' is supported for SNMP SET operations.
U32 juniAaaSubscriberIpv6RouterIndex	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.16	Unsigned32	read-only	The router index that identifies the virtual router associated with this subscriber's IPv6 interface. The value of this object can be used to index the router in the juniRouterTable.
ADR juniAaaSubscriberIpv6AddrIfIdentifier	1.3.6.1.4.1.4874.2.2.20.1.8.4.1.17	Ipv6AddressIfIdentifier	read-only	The client IPv6 Address Interface Identifier assigned to this subscriber.
juniAaaSubscriberRouterSummaryTable	1.3.6.1.4.1.4874.2.2.20.1.8.5		not-accessible	The entries in this table report number of subscribers per router.
juniAaaSubscriberRouterSummaryEntry	1.3.6.1.4.1.4874.2.2.20.1.8.5.1		not-accessible	A specification of subscribers for a router.
U32 juniAaaSubscriberRouterSummaryRouterIndex	1.3.6.1.4.1.4874.2.2.20.1.8.5.1.1	Unsigned32	not-accessible	The router index of the virtual router. The value of this object can be used to retrieve additional information in the router mib.
G32 juniAaaSubscriberRouterSummaryCount	1.3.6.1.4.1.4874.2.2.20.1.8.5.1.2	Gauge32	read-only	The number of subscribers on this router.
juniAaaSubscriberRouterTable	1.3.6.1.4.1.4874.2.2.20.1.8.6		not-accessible	The entries in this table sort subscribers by router ID.
juniAaaSubscriberRouterEntry	1.3.6.1.4.1.4874.2.2.20.1.8.6.1		not-accessible	A specification of subscribers by router ID.
U32 juniAaaSubscriberRouterRouterIndex	1.3.6.1.4.1.4874.2.2.20.1.8.6.1.1	Unsigned32	not-accessible	The router index of the virtual router. The value of this object can be used to retrieve additional information in the router MIB.
U32 juniAaaSubscriberRouterHandle	1.3.6.1.4.1.4874.2.2.20.1.8.6.1.2	Unsigned32	not-accessible	The subscriber handle associated with this subscriber. A subscriber handle is a monotonically increasing integer.
ROW juniAaaSubscriberRouterRowStatus	1.3.6.1.4.1.4874.2.2.20.1.8.6.1.3	RowStatus	read-only	Always has value 'active'.
NUM juniAaaSubscriberLocationType	1.3.6.1.4.1.4874.2.2.20.1.8.7	JuniInterfaceLocationType	read-only	Describes the interpretation of JuniInterfaceLocationValue object values into platform-dependent interface location components, e.g., 'slot.port' on an ERX.
juniAaaSubscriberLocationSummaryTable	1.3.6.1.4.1.4874.2.2.20.1.8.8		not-accessible	The entries in this table report number of subscribers per interface location.
juniAaaSubscriberLocationSummaryEntry	1.3.6.1.4.1.4874.2.2.20.1.8.8.1		not-accessible	A specification of subscribers on an interface location.
NUM juniAaaSubscriberLocationSummaryLocationIndex	1.3.6.1.4.1.4874.2.2.20.1.8.8.1.1	JuniInterfaceLocationValue	not-accessible	The value of a platform interface location.
G32 juniAaaSubscriberLocationSummaryCount	1.3.6.1.4.1.4874.2.2.20.1.8.8.1.2	Gauge32	read-only	The number of subscribers associated with this interface location.
juniAaaSubscriberLocationTable	1.3.6.1.4.1.4874.2.2.20.1.8.9		not-accessible	The entries in this table sort subscribers by interface location.
juniAaaSubscriberLocationEntry	1.3.6.1.4.1.4874.2.2.20.1.8.9.1		not-accessible	An association of a subscriber to an interface location.
NUM juniAaaSubscriberLocationLocationIndex	1.3.6.1.4.1.4874.2.2.20.1.8.9.1.1	JuniInterfaceLocationValue	not-accessible	The value of a platform interface location.
U32 juniAaaSubscriberLocationHandle	1.3.6.1.4.1.4874.2.2.20.1.8.9.1.2	Unsigned32	not-accessible	The subscriber handle associated with this subscriber. A subscriber handle is a monotonically increasing integer.
ROW juniAaaSubscriberLocationRowStatus	1.3.6.1.4.1.4874.2.2.20.1.8.9.1.3	RowStatus	read-only	Always has value 'active'.
G32 juniAaaSubscriberPseudoPeakCount	1.3.6.1.4.1.4874.2.2.20.1.8.10	Gauge32	read-only	The peak number of pseudo-subscribers. The peak count includes successfully authenticated pseudo-subscribers as well as those pseudo-subscribers in the process of being authenticated. Pseudo-subscribers are those whose identities are locally configured on a dynamic link (e.g. an ATM subinterface) via the (imprecisely named) Juniper-SUBSCRIBER-MIB. Some links (e.g. IPoA) provide no link protocol with which to query the identity of a remote user. In such a case, a locally configured pseudo-subscriber can be used to conduct AAA authentication-based configuration of the dynamic link when it becomes active. Pseudo-subscribers are understood to be intended more for dynamic configuration than for actually identifying the remote user. Consequently, the pseudo-subscribers are not reflected in any of the subscriber tables defined in this MIB.
G32 juniAaaSubscriberPseudoCount	1.3.6.1.4.1.4874.2.2.20.1.8.11	Gauge32	read-only	The current number of pseudo-subscribers. The pseudo-subscriber count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated. Pseudo-subscribers are those whose identities are locally configured on a dynamic link (e.g. an ATM subinterface) via the (imprecisely named) Juniper-SUBSCRIBER-MIB. Some links (e.g. IPoA) provide no link protocol with which to query the identity of a remote user. In such a case, a locally configured pseudo-subscriber can be used to conduct AAA authentication-based configuration of the dynamic link when it becomes active. Pseudo-subscribers are understood to be intended more for dynamic configuration than for actually identifying the remote user. Consequently, the pseudo-subscribers are not reflected in any of the subscriber tables defined in this MIB.
juniAaaSubscriberIpv6AddrPrefixTable	1.3.6.1.4.1.4874.2.2.20.1.8.12		not-accessible	The entries in this table represent IPv6 Address Prefixes by subscriber handle value.
juniAaaSubscriberIpv6AddrPrefixEntry	1.3.6.1.4.1.4874.2.2.20.1.8.12.1		not-accessible	A specification of IPv6 Address Prefixes by subscriber handle.
ADR juniAaaSubscriberIpv6AddrPrefix	1.3.6.1.4.1.4874.2.2.20.1.8.12.1.1	Ipv6AddressPrefix	read-only	The client IPv6 Address Prefix assigned to this subscriber.
I32 juniAaaSubscriberIpv6AddrPrefixSize	1.3.6.1.4.1.4874.2.2.20.1.8.12.1.2	Integer32	read-only	The size of the client IPv6 Address Prefix assigned to this subscriber.
juniAaaSubscriberExtTable	1.3.6.1.4.1.4874.2.2.20.1.8.13		not-accessible	The entries in this table represent subscribers extension attributes by subscriber handle value.
juniAaaSubscriberExtEntry	1.3.6.1.4.1.4874.2.2.20.1.8.13.1		not-accessible	A specification of subscribers extension attributes by subscriber handle.
STR juniAaaSubscriberExtUserName	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.1	DisplayString	read-only	The user name associated with this subscriber.
STR juniAaaSubscriberExtLoginTime	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.2	DisplayString	read-only	The time this subscriber logged in using AAA protocol.
IP juniAaaSubscriberExtIpAddress	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.3	IpAddress	read-only	The client IP Address assigned to this subscriber.
IP juniAaaSubscriberExtIpAddressMask	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.4	IpAddress	read-only	The client IP Address Mask assigned to this subscriber.
ADR juniAaaSubscriberExtAddrAssignType	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.5	JuniAddressAssignType	read-only	The address assignment type for this subscriber.
JUN juniAaaSubscriberExtState	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.6	JuniSubscriberState	read-only	The state of this subscriber.
JUN juniAaaSubscriberExtClientType	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.7	JuniSubscriberClientType	read-only	The client type for this subscriber. Certain client types (e.g., 'other') might be suppressed from representation in this table.
STR juniAaaSubscriberExtAcctSessionId	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.8	DisplayString	read-only	Account session ID associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 44 for RADIUS.
STR juniAaaSubscriberExtClass	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.9	DisplayString	read-only	Classification attribute associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 25 for RADIUS.
U32 juniAaaSubscriberExtNasPort	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.10	Unsigned32	read-only	Associated NAS port with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 5 for RADIUS.
U32 juniAaaSubscriberExtNasPortType	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.11	Unsigned32	read-only	Associated NAS port type attribute associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 61 for RADIUS.
OCT juniAaaSubscriberExtCalledStationId	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.12	OCTET STRING	read-only	Called ID associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 30 for RADIUS.
OCT juniAaaSubscriberExtCallingStationId	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.13	OCTET STRING	read-only	Calling ID associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 31 for RADIUS.
I32 juniAaaSubscriberExtL2tpTunnelId	1.3.6.1.4.1.4874.2.2.20.1.8.13.1.14	Integer32	read-only	L2TP Tunnel ID associated with this subscriber of concerned LNS. A value 0 for this attribute indicates the terminated subscriber.
juniAaaSubscriberInterfaceSummaryTable	1.3.6.1.4.1.4874.2.2.20.1.8.14		not-accessible	The entries in this table report number of subscribers per subscriber interface which includes the port type (1 = atm; 2 = ethernet), slot, port and sub-interface.
juniAaaSubscriberInterfaceSummaryEntry	1.3.6.1.4.1.4874.2.2.20.1.8.14.1		not-accessible	A specification of subscribers on an subscriber interface.
NUM juniAaaSubscriberInterfaceSummaryIndex	1.3.6.1.4.1.4874.2.2.20.1.8.14.1.1	JuniSubscriberInterfaceValue	not-accessible	The value of a subscriber interface.
I32 juniAaaSubscriberSubInterfaceSummaryIndex	1.3.6.1.4.1.4874.2.2.20.1.8.14.1.2	Integer32	not-accessible	The value of a subscriber sub-interface.
G32 juniAaaSubscriberInterfaceSummaryCount	1.3.6.1.4.1.4874.2.2.20.1.8.14.1.3	Gauge32	read-only	The number of subscribers associated with this subscriber interface.
juniAaaSubscriberInterfaceTable	1.3.6.1.4.1.4874.2.2.20.1.8.15		not-accessible	The subscriber entries in this table sorted by subscriber interface.
juniAaaSubscriberInterfaceEntry	1.3.6.1.4.1.4874.2.2.20.1.8.15.1		not-accessible	An association of a subscriber to a subscriber interface.
NUM juniAaaSubscriberInterfaceIndex	1.3.6.1.4.1.4874.2.2.20.1.8.15.1.1	JuniSubscriberInterfaceValue	not-accessible	The value of a subscriber interface. This includes the port type (1 = ATM; 2 = Ethernet), slot, port, and sub-interface.
I32 juniAaaSubscriberSubInterfaceIndex	1.3.6.1.4.1.4874.2.2.20.1.8.15.1.2	Integer32	not-accessible	The value of a subscriber sub-interface.
U32 juniAaaSubscriberInterfaceHandle	1.3.6.1.4.1.4874.2.2.20.1.8.15.1.3	Unsigned32	not-accessible	The subscriber handle associated with this subscriber interface. A subscriber handle is a monotonically increasing integer.
ROW juniAaaSubscriberInterfaceRowStatus	1.3.6.1.4.1.4874.2.2.20.1.8.15.1.4	RowStatus	read-only	Always has value 'active'.
juniAaaSubscriberSlotSummaryTable	1.3.6.1.4.1.4874.2.2.20.1.8.16		not-accessible	The entries in this table report number of subscribers per slot.
juniAaaSubscriberSlotSummaryEntry	1.3.6.1.4.1.4874.2.2.20.1.8.16.1		not-accessible	A specification of subscribers for a slot.
U32 juniAaaSubscriberSlotSummarySlotIndex	1.3.6.1.4.1.4874.2.2.20.1.8.16.1.1	Unsigned32	not-accessible	The index of the slot.
G32 juniAaaSubscriberSlotSummaryCount	1.3.6.1.4.1.4874.2.2.20.1.8.16.1.2	Gauge32	read-only	The number of subscribers on this slot.
juniAaaSubscriberSlotTable	1.3.6.1.4.1.4874.2.2.20.1.8.17		not-accessible	The subscriber in this table sorted by slot.
juniAaaSubscriberSlotEntry	1.3.6.1.4.1.4874.2.2.20.1.8.17.1		not-accessible	A specification of subscribers by slot.
U32 juniAaaSubscriberSlotIndex	1.3.6.1.4.1.4874.2.2.20.1.8.17.1.1	Unsigned32	not-accessible	The index of the slot.
U32 juniAaaSubscriberSlotHandle	1.3.6.1.4.1.4874.2.2.20.1.8.17.1.2	Unsigned32	not-accessible	The subscriber handle associated with this slot. The subscriber handle is a monotonically increasing integer.
ROW juniAaaSubscriberSlotRowStatus	1.3.6.1.4.1.4874.2.2.20.1.8.17.1.3	RowStatus	read-only	Always has value 'active'.
juniAaaCapabilities	1.3.6.1.4.1.4874.2.2.20.1.9
T/F juniAaaAccountingCapability	1.3.6.1.4.1.4874.2.2.20.1.9.1	TruthValue	read-only	Indicates whether this system supports AAA Accounting. The value true(1) indicate that it does, false(2) indicates that it does not.
T/F juniAaaAddressAssignmentCapability	1.3.6.1.4.1.4874.2.2.20.1.9.2	TruthValue	read-only	Indicates whether this system supports AAA address assignment. The value true(1) indicates that it does, false(2) indicates that it does not.
T/F juniAaaBrasCapability	1.3.6.1.4.1.4874.2.2.20.1.9.3	TruthValue	read-only	Indicates whether this system supports AAA BRAS functionality. The value true(1) indicates that it does, false(2) indicates that it does not.
T/F juniAaaTunnelingCapability	1.3.6.1.4.1.4874.2.2.20.1.9.4	TruthValue	read-only	Indicates whether this system supports AAA tunneling. The value true(1) indicates that it does, false(2) indicates that it does not.
juniAaaMIBConformance	1.3.6.1.4.1.4874.2.2.20.4
juniAaaMIBCompliances	1.3.6.1.4.1.4874.2.2.20.4.1
juniAaaCompliance	1.3.6.1.4.1.4874.2.2.20.4.1.1			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added.
juniAaaCompliance2	1.3.6.1.4.1.4874.2.2.20.4.1.2			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added and new groupings were defined.
juniAaaCompliance3	1.3.6.1.4.1.4874.2.2.20.4.1.3			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the juniAaaAssignDomainStripDomain object was added to the B-RAS group.
juniAaaCompliance4	1.3.6.1.4.1.4874.2.2.20.4.1.4			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new assignment delimiter objects were added to the B-RAS group.
juniAaaCompliance5	1.3.6.1.4.1.4874.2.2.20.4.1.5			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the subscriber and capabilities groups were added.
juniAaaCompliance6	1.3.6.1.4.1.4874.2.2.20.4.1.6			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when support was added for subscriber information by interface location.
juniAaaCompliance7	1.3.6.1.4.1.4874.2.2.20.4.1.7			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when several new objects were added.
juniAaaCompliance8	1.3.6.1.4.1.4874.2.2.20.4.1.8			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added to the B-RAS and tunnel groups.
juniAaaCompliance9	1.3.6.1.4.1.4874.2.2.20.4.1.9			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added to the B-RAS group.
juniAaaCompliance10	1.3.6.1.4.1.4874.2.2.20.4.1.10			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added to the B-RAS, Subscriber and Address groups.
juniAaaCompliance11	1.3.6.1.4.1.4874.2.2.20.4.1.11			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance12	1.3.6.1.4.1.4874.2.2.20.4.1.12			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance13	1.3.6.1.4.1.4874.2.2.20.4.1.13			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance14	1.3.6.1.4.1.4874.2.2.20.4.1.14			The compliance statement for systems supporting AAA.
juniAaaCompliance15	1.3.6.1.4.1.4874.2.2.20.4.1.15			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance16	1.3.6.1.4.1.4874.2.2.20.4.1.16			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance17	1.3.6.1.4.1.4874.2.2.20.4.1.17			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance18	1.3.6.1.4.1.4874.2.2.20.4.1.18			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance19	1.3.6.1.4.1.4874.2.2.20.4.1.19			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance20	1.3.6.1.4.1.4874.2.2.20.4.1.20			Obsolete compliance statement for systems supporting AAA.
juniAaaCompliance21	1.3.6.1.4.1.4874.2.2.20.4.1.21			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the juniAaaMonitorIngressTrafficOnly object was added to the B-RAS group.
juniAaaCompliance22	1.3.6.1.4.1.4874.2.2.20.4.1.22			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the juniAaaAssignDomainBackupPoolName object was added to the B-RAS group.
juniAaaCompliance23	1.3.6.1.4.1.4874.2.2.20.4.1.23			Obsolete compliance statement for systems supporting AAA. This statement became obsolete when juniAaaFramedIpv6PrefixAsIpv6NdRaPrefix and juniAaaDelegatedIpv6PrefixAsDhcpv6DelegatedPrefix objects were added to the B-RAS group.
juniAaaCompliance24	1.3.6.1.4.1.4874.2.2.20.4.1.24			The compliance statement for systems supporting AAA.
juniAaaMIBGroups	1.3.6.1.4.1.4874.2.2.20.4.2
juniAaaGroup	1.3.6.1.4.1.4874.2.2.20.4.2.1			Obsolete collection of objects providing management of AAA functionality in a Juniper product. This group became obsolete when new objects were added.
juniAaaGroup2	1.3.6.1.4.1.4874.2.2.20.4.2.2			Obsolete collection of objects providing management of AAA functionality in a Juniper product. This group became obsolete when new objects were added and new groupings were defined.
juniAaaBasicGroup	1.3.6.1.4.1.4874.2.2.20.4.2.3			The basic collection of objects providing management of AAA functionality in a Juniper product.
juniAaaBrasGroup	1.3.6.1.4.1.4874.2.2.20.4.2.4			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when the juniAaaAssignDomainStripDomain object was added.
juniAaaTunnelGroup	1.3.6.1.4.1.4874.2.2.20.4.2.5			Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product. This group became obsolete when the maximum sessions object was added.
juniAaaAuthenticationGroup	1.3.6.1.4.1.4874.2.2.20.4.2.6			Obsolete collection of objects providing management of AAA authentication functionality in a Juniper product. This group became obsolete when the authentication methods table was added.
juniAaaAccountingGroup	1.3.6.1.4.1.4874.2.2.20.4.2.7			Obsolete collection of objects providing management of AAA accounting functionality in a Juniper product. This group became obsolete when the juniAaaAcctSendStopOnAaaDeny object was added.
juniAaaAddressGroup	1.3.6.1.4.1.4874.2.2.20.4.2.8			Obsolete collection of objects providing management of AAA address assignment functionality in a Juniper product. This group became obsolete when IPv6 support was added.
juniAaaBrasGroup2	1.3.6.1.4.1.4874.2.2.20.4.2.9			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when new assignment delimiter objects were added.
juniAaaBrasGroup3	1.3.6.1.4.1.4874.2.2.20.4.2.10			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when new objects were added.
juniAaaSubscriberGroup	1.3.6.1.4.1.4874.2.2.20.4.2.11			Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product. This group became obsolete when support was added for monitoring subscriber information by interface location.
juniAaaCapabilitiesGroup	1.3.6.1.4.1.4874.2.2.20.4.2.12			The collection of objects providing management of AAA Capabilities functionality in a Juniper product.
juniAaaSubscriberGroup2	1.3.6.1.4.1.4874.2.2.20.4.2.13			Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product. This group became obsolete when the pseudo-subscriber meters were added.
juniAaaAccountingGroup2	1.3.6.1.4.1.4874.2.2.20.4.2.14			Obsolete collection of objects providing management of AAA accounting functionality in a Juniper product. This group became obsolete when the accounting methods table was added.
juniAaaBrasGroup4	1.3.6.1.4.1.4874.2.2.20.4.2.15			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when assign domain pool name was added.
juniAaaSubscriberGroup3	1.3.6.1.4.1.4874.2.2.20.4.2.16			Obsoleted collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product. This group became obsolete when IPv6 support was added.
juniAaaBrasGroup5	1.3.6.1.4.1.4874.2.2.20.4.2.17			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when PADN support was added.
juniAaaTunnelGroup2	1.3.6.1.4.1.4874.2.2.20.4.2.18			Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product.
juniAaaBrasGroup6	1.3.6.1.4.1.4874.2.2.20.4.2.19			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when IPv6 support was added.
juniAaaBrasGroup7	1.3.6.1.4.1.4874.2.2.20.4.2.20			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaAddressGroup2	1.3.6.1.4.1.4874.2.2.20.4.2.21			The collection of objects providing management of AAA address assignment functionality in a Juniper product.
juniAaaSubscriberGroup4	1.3.6.1.4.1.4874.2.2.20.4.2.22			Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product.
juniAaaBrasGroup8	1.3.6.1.4.1.4874.2.2.20.4.2.23			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaBrasGroup9	1.3.6.1.4.1.4874.2.2.20.4.2.24			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaTunnelGroup3	1.3.6.1.4.1.4874.2.2.20.4.2.25			Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product.
juniAaaAccountingGroup3	1.3.6.1.4.1.4874.2.2.20.4.2.26			Obsolete collection of objects providing management of AAA accounting functionality in a Juniper product.
juniAaaAuthenticationGroup2	1.3.6.1.4.1.4874.2.2.20.4.2.27			Obsolete collection of objects providing management of AAA authentication functionality in a Juniper product.
juniAaaAuthenticationGroup3	1.3.6.1.4.1.4874.2.2.20.4.2.28			The collection of objects providing management of AAA authentication functionality in a Juniper product.
juniAaaAccountingGroup4	1.3.6.1.4.1.4874.2.2.20.4.2.29			The collection of objects providing management of AAA accounting functionality in a Juniper product.
juniAaaTunnelGroup4	1.3.6.1.4.1.4874.2.2.20.4.2.30			Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product.
juniAaaSubscriberGroup5	1.3.6.1.4.1.4874.2.2.20.4.2.31			The collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product.
juniAaaBrasGroup10	1.3.6.1.4.1.4874.2.2.20.4.2.32			Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaTunnelGroup5	1.3.6.1.4.1.4874.2.2.20.4.2.33			The collection of collection of objects providing management of AAA tunneling functionality in a Juniper product.
juniAaaBrasGroup11	1.3.6.1.4.1.4874.2.2.20.4.2.34			The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaAccountingGroup5	1.3.6.1.4.1.4874.2.2.20.4.2.35			The collection of objects providing management of AAA accounting functionality in a Juniper product.
juniAaaBrasGroup12	1.3.6.1.4.1.4874.2.2.20.4.2.36			The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaBrasGroup13	1.3.6.1.4.1.4874.2.2.20.4.2.37			The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaBrasGroup14	1.3.6.1.4.1.4874.2.2.20.4.2.38			The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
juniAaaBrasGroup15	1.3.6.1.4.1.4874.2.2.20.4.2.39			The collection of objects providing management of AAA B-RAS functionality in a Juniper product.

RFC description

Authentication, Authorization, and Accounting (AAA) configuration for Juniper Networks routers.

Start monitoring Juniper ERX/E-series broadband edge router (BRAS AAA) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-AAA-MIB