HPN-ICF-TE-TUNNEL-MIB

All MIBs › HPN-ICF-TE-TUNNEL-MIB

Last Updated: 2011-03-24

Category: MPLS and Traffic Engineering, Vendor: H3C/HH3C, Vendor: HP/HPE

Description: Manages MPLS TE tunnel attributes, bandwidth reservation, and protection configuration on HP/Comware MPLS devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-TE-TUNNEL-MIB?

HPN-ICF-TE-TUNNEL-MIB is an HP/H3C Comware private MIB for managing MPLS Traffic Engineering (TE) tunnels, including static CR-LSPs (Constraint-based Routed Label Switched Paths) and tunnel-to-LSP correlation objects. It exposes configuration data such as static CR-LSP labels, names, roles, and cross-connect pointers, alongside status objects that indicate whether a given LSP or tunnel binding is operational. From a monitoring standpoint, it lets an operator track the operational status of each configured TE tunnel/CR-LSP, detect label or role misconfigurations, and confirm that a tunnel is correctly bound to its cross-connect path, which is essential for verifying MPLS forwarding-plane software state. This MIB depends heavily on the standard MPLS-related IETF MIBs (e.g., MPLS-TE-MIB, MPLS-LSR-MIB) for the underlying LSP and cross-connect concepts it extends. It is typically deployed on HP/H3C Comware MPLS-capable routers and provider-edge devices in service-provider or large enterprise WAN backbones. Engineers can download the HPN-ICF-TE-TUNNEL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-TE-TUNNEL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP/H3C Comware MPLS routers and provider-edge devices

Monitoring Examples

An engineer polls hpnicfTeTunnelStaticCrlspTable, keyed by hpnicfTeTunnelStaticCrlspInLabel, to verify that a named static CR-LSP (hpnicfTeTunnelStaticCrlspName) is configured with the correct hpnicfTeTunnelStaticCrlspRole (ingress/transit/egress) and that hpnicfTeTunnelStaticCrlspStatus shows it as active. They cross-reference hpnicfTeTunnelStaticCrlspXCPointer to confirm the LSP is correctly cross-connected. Separately, walking hpnicfTeTunnelCoTable by hpnicfTeTunnelCoIndex reveals which hpnicfTeTunnelCoLspInstance is currently mapped to a given TE tunnel, and a mismatch or missing entry indicates a tunnel setup failure.

What Can Be Monitored

static CR-LSP status
CR-LSP label/role assignment
cross-connect pointer binding
tunnel-to-LSP instance mapping
maximum tunnel index/capacity

Imported Objects

From HPN-ICF-OID-MIB

hpnicfCommon

OBJECT-IDENTITY

From MPLS-TC-STD-MIB

MplsExtendedTunnelId
MplsLabel
MplsTunnelIndex
MplsTunnelInstanceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowPointer

How to Use in IPNetwork Monitor

Example using hpnicfTeTunnelStaticCrlspStatus OID:

Select an HP/H3C Comware router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpnicfTeTunnelStaticCrlspStatus into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Indicates the actual status of this static-crlsp, The value must be up when the static-crlsp status is up and the value must be down when the static-crlsp status is down. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is anything other than 'up', since that indicates the condition this object reports has changed to one worth investigating. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfTeTunnel	1.3.6.1.4.1.11.2.14.11.15.2.115			This MIB contains managed object definitions for the Multiprotocol Label Switching (MPLS) Te Tunnel.
hpnicfTeTunnelScalars	1.3.6.1.4.1.11.2.14.11.15.2.115.1
MPL hpnicfTeTunnelMaxTunnelIndex	1.3.6.1.4.1.11.2.14.11.15.2.115.1.1	MplsTunnelIndex	read-only	The max value of tunnel id is permitted configure on the device.
hpnicfTeTunnelObjects	1.3.6.1.4.1.11.2.14.11.15.2.115.2
hpnicfTeTunnelStaticCrlspTable	1.3.6.1.4.1.11.2.14.11.15.2.115.2.1		not-accessible	This table contains information for static-crlsp, and through this to get detail information about this static-crlsp. Only support transit LSR and egress LSR.
hpnicfTeTunnelStaticCrlspEntry	1.3.6.1.4.1.11.2.14.11.15.2.115.2.1.1		not-accessible	The entry in this table describes static-crlsp information.
MPL hpnicfTeTunnelStaticCrlspInLabel	1.3.6.1.4.1.11.2.14.11.15.2.115.2.1.1.1	MplsLabel	not-accessible	This is unique label value that manualy assigned. Uniquely identifies a static-crlsp. Managers should use this to obtain detail static-crlsp information.
OCT hpnicfTeTunnelStaticCrlspName	1.3.6.1.4.1.11.2.14.11.15.2.115.2.1.1.2	OCTET STRING	read-only	The unique name assigned to the static-crlsp.
INT hpnicfTeTunnelStaticCrlspStatusEx	1.3.6.1.4.1.11.2.14.11.15.2.115.2.1.1.3	INTEGER	read-only	Indicates the actual status of this static-crlsp, The value must be up when the static-crlsp status is up and the value must be down when the static-crlsp status is down.
INT hpnicfTeTunnelStaticCrlspRole	1.3.6.1.4.1.11.2.14.11.15.2.115.2.1.1.4	INTEGER	read-only	This value indicate the role of this static-crlsp. This value must be transit at transit point of the tunnel, and tail at terminating point of the tunnel.
NUM hpnicfTeTunnelStaticCrlspXCPointer	1.3.6.1.4.1.11.2.14.11.15.2.115.2.1.1.5	RowPointer	read-only	This pointer unique identify a row of mplsXCTable. This value should be zeroDotZero when the static-crlsp is down. The mplsXCTable identifies the segments that compose this tunnel, their characteristics, and relationships to each other.
hpnicfTeTunnelCoTable	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2		not-accessible	This table contains information for Co-routed reverse crlsp and infomation of Co-routed bidirectional Tunnel Interface. If hpnicfCorouteTunnelLspInstance is zero, to obtain infomation of Co-routed bidirectional Tunnel Interface, otherwise to obtain Co-routed reverse crlsp infomation.
hpnicfTeTunnelCoEntry	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1		not-accessible	The entry in this table describes Co-routed infomation of bidirectional Tunnel Interface and reserver lsp information.
MPL hpnicfTeTunnelCoIndex	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1.1	MplsTunnelIndex	not-accessible	Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs that specified at originating point. This value should be equal to the value signaled in the Tunnel Id of the Session object.
MPL hpnicfTeTunnelCoLspInstance	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1.2	MplsTunnelInstanceIndex	not-accessible	When obtain infomation of Co-routed bidirectional Tunnel Interface, this vlaue should be zero. And this value must be LspID to obtain reverse crlsp information. Values greater than 0, but less than or equal to 65535, should be useless.
MPL hpnicfTeTunnelCoIngressLSRId	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1.3	MplsExtendedTunnelId	not-accessible	Identity the ingress LSR associated with this tunnel instance. This vlaue is equal to the LsrID of originating endpoint.
MPL hpnicfTeTunnelCoEgressLSRId	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1.4	MplsExtendedTunnelId	not-accessible	Identity of the egress LSR associated with this tunnel instance. This vlaue is equal to the LsrID of terminating point.
INT hpnicfTeTunnelCoBiMode	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1.5	INTEGER	read-only	This vlaue indicated the bidirection mode of tunnel interface. The valuemust be coroutedActive at the originating point of the tunnel and coroutedPassive at the terminating point.
MPL hpnicfTeTunnelCoReverseLspInstance	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1.6	MplsTunnelInstanceIndex	read-only	This value indicated the reverse lsp instance, and should be equal to obverse lsp instance.
NUM hpnicfTeTunnelCoReverseLspXCPointer	1.3.6.1.4.1.11.2.14.11.15.2.115.2.2.1.7	RowPointer	read-only	This pointer unique index to mplsXCTable of the reverse lsp. The mplsXCTable identifies the segments that compose this tunnel, their characteristics, and relationships to each other. A value of zeroDotZero indicate that there is no crlsp assigned to this.
hpnicfTeTunnelPsTable	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3		not-accessible	This table defines some objects for managers to obtain TE tunnel Protection Switching group current status information.
hpnicfTeTunnelPsEntry	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1		not-accessible	The entry in this table describes TE tunnel Protection Switching group infromation.
MPL hpnicfTeTunnelPsIndex	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.1	MplsTunnelIndex	not-accessible	Uniquely identifies a TE tunnel Protection Switching group instance. This value must be equal to the tunnel id of work tunnel instance.
MPL hpnicfTeTunnelPsIngressLSRId	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.2	MplsExtendedTunnelId	not-accessible	Identity the ingress LSR associated with work tunnel instance.
MPL hpnicfTeTunnelPsEgressLSRId	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.3	MplsExtendedTunnelId	not-accessible	Identity of the egress LSR associated with work tunnel instance.
MPL hpnicfTeTunnelPsProtectIndex	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.4	MplsTunnelIndex	read-only	Uniquely identifies a TE tunnel Protection Switching group instance. This value must be equal to the tunnel id of TE tunnel Protection Switching group instance.
MPL hpnicfTeTunnelPsProtectIngressLSRId	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.5	MplsExtendedTunnelId	read-only	Identity the ingress LSR associated with TE tunnel Protection Switching group instance.
MPL hpnicfTeTunnelPsProtectEgressLSRId	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.6	MplsExtendedTunnelId	read-only	Identity of the egress LSR associated with TE tunnel Protection Switching group instance.
INT hpnicfTeTunnelPsProtectType	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.7	INTEGER	read-only	This value indicated TE tunnel Protection Switching group type. The default value is oneToOne.
INT hpnicfTeTunnelPsRevertiveMode	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.8	INTEGER	read-only	This value indicated protect switch mode. The value must be revertive or nonRevertive, default value is revertive.
U32 hpnicfTeTunnelPsWtrTime	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.9	Unsigned32	read-only	The cycle time that switch to protect tunnel.
U32 hpnicfTeTunnelPsHoldOffTime	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.10	Unsigned32	read-only	This value is switchback delay time. When detected the work path fault, switch to protect path after this time.
INT hpnicfTeTunnelPsSwitchMode	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.11	INTEGER	read-only	This value indicated TE tunnel Protection Switching group switch mode.
INT hpnicfTeTunnelPsWorkPathStatus	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.12	INTEGER	read-only	This value indicates work path status. none, noDefect, inDefect will be used.
INT hpnicfTeTunnelPsProtectPathStatus	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.13	INTEGER	read-only	This value indicates protect path status. none, noDefect, inDefect(3) will be used.
INT hpnicfTeTunnelPsSwitchResult	1.3.6.1.4.1.11.2.14.11.15.2.115.2.3.1.14	INTEGER	read-only	This value indicated current using path is work path or protect path.
hpnicfTeTunnelNotifications	1.3.6.1.4.1.11.2.14.11.15.2.115.3
hpnicfTeTunnelNotificationsPrefix	1.3.6.1.4.1.11.2.14.11.15.2.115.3.0
NTF hpnicfTeTunnelPsSwitchWtoP	1.3.6.1.4.1.11.2.14.11.15.2.115.3.0.1			This notification is generated when protect workgroup switch from work tunnel to protect tunnel.
NTF hpnicfTeTunnelPsSwitchPtoW	1.3.6.1.4.1.11.2.14.11.15.2.115.3.0.2			This notification is generated when protect workgroup switch from protect tunnel to work tunnel.
hpnicfTeTunnelConformance	1.3.6.1.4.1.11.2.14.11.15.2.115.4
hpnicfTeTunnelCompliances	1.3.6.1.4.1.11.2.14.11.15.2.115.4.1
hpnicfTeTunnelCompliance	1.3.6.1.4.1.11.2.14.11.15.2.115.4.1.1			The compliance statement for SNMP.
hpnicfTeTunnelGroups	1.3.6.1.4.1.11.2.14.11.15.2.115.4.2
hpnicfTeTunnelNotificationsGroup	1.3.6.1.4.1.11.2.14.11.15.2.115.4.2.1			This group contains MPLS Te Tunnel traps.
hpnicfTeTunnelScalarsGroup	1.3.6.1.4.1.11.2.14.11.15.2.115.4.2.2			Scalar object needed to implement MPLS te tunnels.
hpnicfTeTunnelStaticCrlspGroup	1.3.6.1.4.1.11.2.14.11.15.2.115.4.2.3			Objects for quering static-crlsp information.
hpnicfTeTunnelCorouteGroup	1.3.6.1.4.1.11.2.14.11.15.2.115.4.2.4			Objects for quering Co-routed reverse crlsp information.
hpnicfTeTunnelPsGroup	1.3.6.1.4.1.11.2.14.11.15.2.115.4.2.5			Objects for quering protect workgroup information.

RFC description

Multiprotocol Label Switching (MPLS) Traffic Engineering (TE) Tunnel management MIB for HP devices.

Start monitoring HP/H3C Comware routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-TE-TUNNEL-MIB