HM2-TIMESYNC-MIB

All MIBs › HM2-TIMESYNC-MIB

Organization: Hirschmann Automation and Control GmbH

Last Updated: 2011-03-16

Category: Protocol: NTP, Technology: Time Synchronization, Vendor: Belden

Description: Hirschmann HiOS (HM2) time synchronization MIB for NTP, SNTP, and IEEE 1588 PTP configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HM2-TIMESYNC-MIB?

HM2-TIMESYNC-MIB is a Hirschmann HiOS proprietary MIB managing time synchronization on Hirschmann switches, covering NTP/SNTP client and server configuration alongside IEEE 1588 Precision Time Protocol (PTP) settings referenced in its description. It exposes the device's current UTC and local time, configured time source, and detailed SNTP server/client settings including broadcast mode address and port. Its monitoring value is verifying that device clocks remain accurate and synchronized, which is critical for correlating log timestamps, SNMP trap timing, and coordinating time-sensitive industrial protocols across a network; a stalled or unreachable time source directly undermines fault diagnosis elsewhere. It builds on standard NTP/SNTP (RFC 4330) and IEEE 1588 PTP protocols as its underlying time-sync mechanisms. It is deployed on Hirschmann industrial Ethernet switches in substations, factories, or transportation systems requiring tightly synchronized clocks. Engineers can download the HM2-TIMESYNC-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HM2-TIMESYNC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Hirschmann HiOS industrial Ethernet switch

Monitoring Examples

An administrator checks hm2SystemUtcTime and hm2SystemTimeSource to confirm the switch has a valid, actively-synced time source, and hm2SystemLocalTime/hm2SystemLocalOffset to verify local time zone handling is correct. The hm2SntpServerAdminState and hm2SntpServerStatus objects show whether the SNTP client is enabled and successfully synchronizing, while hm2SntpServerBroadcastAdminState and hm2SntpServerBroadcastAddrType/Addr describe broadcast-mode time distribution settings. If hm2SntpServerStatus reports a failure, the admin knows switch logs and traps may carry drifting timestamps until the time source issue is resolved.

What Can Be Monitored

current UTC/local time
configured time source
SNTP client admin state and sync status
SNTP broadcast configuration

Imported Objects

From HM2-TC-MIB

HmEnabledStatus
HmTimeSeconds1970
hm2ConfigurationMibs	OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType
InetPortNumber

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using hm2SystemTimeSource OID:

Select a Hirschmann HiOS industrial Ethernet switch (NTP/SNTP/PTP time sync) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hm2SystemTimeSource into the Find box to locate it in the OID tree, then select it and click OK. Shows the source of the system time. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is 'local', since that means the device has fallen back to its own clock instead of an external time reference. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hm2TimeSyncMib	1.3.6.1.4.1.248.11.50			Hirschmann Time Sync MIB. Copyright (C) 2011. All Rights Reserved.
hm2TimeSyncMibNotifications	1.3.6.1.4.1.248.11.50.0
NTF hm2Ptp2SynchronizationChange	1.3.6.1.4.1.248.11.50.0.1			This notification is sent if the PTP synchronization status is changed.
NTF hm2SntpClientSynchronizationChangeTrap	1.3.6.1.4.1.248.11.50.0.10			This notification is sent if the SNTP synchronization status (hm2SntpClientStatus) is changed.
hm2TimeSyncMibObjects	1.3.6.1.4.1.248.11.50.1
hm2SystemTimeGroup	1.3.6.1.4.1.248.11.50.1.1
HMT hm2SystemUtcTime	1.3.6.1.4.1.248.11.50.1.1.1	HmTimeSeconds1970	read-write	Time measured in seconds since 00:00:00 UTC, January 1, 1970. The clock of the device may be set using this variable.
INT hm2SystemTimeSourceEx	1.3.6.1.4.1.248.11.50.1.1.2	INTEGER	read-only	Shows the source of the system time.
HMT hm2SystemLocalTime	1.3.6.1.4.1.248.11.50.1.1.3	HmTimeSeconds1970	read-write	The current local time. This includes the timezone offset and if supported summertime offset. Measured in seconds since 00:00:00, January 1, 1970.
I32 hm2SystemLocalOffset	1.3.6.1.4.1.248.11.50.1.1.4	Integer32	read-write	The difference between the local timezone and UTC in minutes.
hm2SntpGroup	1.3.6.1.4.1.248.11.50.1.2
hm2SntpServerGroup	1.3.6.1.4.1.248.11.50.1.2.1
HME hm2SntpServerAdminState	1.3.6.1.4.1.248.11.50.1.2.1.1	HmEnabledStatus	read-write	Enables/disables SNTP server admin mode.
INE hm2SntpServerPort	1.3.6.1.4.1.248.11.50.1.2.1.2	InetPortNumber	read-write	The local port number used to listen for client requests.
HME hm2SntpServerOnlyIfSync	1.3.6.1.4.1.248.11.50.1.2.1.3	HmEnabledStatus	read-write	The SNTP server is enabled only if synchronized to another external time reference. (e.g. NTP or PTP).
INT hm2SntpServerStatus	1.3.6.1.4.1.248.11.50.1.2.1.4	INTEGER	read-only	Operational status of the SNTP server.
hm2SntpServerBroadcastGroup	1.3.6.1.4.1.248.11.50.1.2.2
HME hm2SntpServerBroadcastAdminState	1.3.6.1.4.1.248.11.50.1.2.2.1	HmEnabledStatus	read-write	Enables/disables SNTP server broadcast admin mode.
IPt hm2SntpServerBroadcastAddrType	1.3.6.1.4.1.248.11.50.1.2.2.2	InetAddressType	read-write	Address type.
IP hm2SntpServerBroadcastAddr	1.3.6.1.4.1.248.11.50.1.2.2.3	InetAddress	read-write	Destination address for SNTP broadcast or multicast.
INE hm2SntpServerBroadcastPort	1.3.6.1.4.1.248.11.50.1.2.2.4	InetPortNumber	read-write	The port number to send the broadcast packets to the clients.
I32 hm2SntpServerBroadcastInterval	1.3.6.1.4.1.248.11.50.1.2.2.5	Integer32	read-write	Interval of SNTP broadcast messages send in seconds.
hm2SntpServerBroadcastVlanTable	1.3.6.1.4.1.248.11.50.1.2.2.10		not-accessible	This table contains all VLANs used for SNTP server broadcast or multicast messages.
hm2SntpServerBroadcastVlanEntry	1.3.6.1.4.1.248.11.50.1.2.2.10.1		not-accessible	The SNTP broadcast server VLAN objects.
I32 hm2SntpServerBroadcastVlan	1.3.6.1.4.1.248.11.50.1.2.2.10.1.1	Integer32	read-only	VLAN used for SNTP server broadcast or multicast messages.
ROW hm2SntpServerBroadcastVlanRowStatus	1.3.6.1.4.1.248.11.50.1.2.2.10.1.2	RowStatus	read-create	Indicates the status of an entry in this table, and is used to create/delete entries. Objects within this table can by changed while the status is 'active'.
hm2SntpClientGroup	1.3.6.1.4.1.248.11.50.1.2.3
HME hm2SntpClientAdminState	1.3.6.1.4.1.248.11.50.1.2.3.1	HmEnabledStatus	read-write	Enables/disables the SNTP client admin mode.
INT hm2SntpClientOperatingMode	1.3.6.1.4.1.248.11.50.1.2.3.2	INTEGER	read-write	Enables/disables SNTP client operating mode. In 'unicast' mode, the client sends a request to a designated unicast server and expects a reply from that server. In 'broadcast' client mode, it sends no request and waits for a broadcast from one or more broadcast servers.
HME hm2SntpClientDisableAfterSync	1.3.6.1.4.1.248.11.50.1.2.3.3	HmEnabledStatus	read-write	When set to 'enable' the SNTP client is disabled after the device is synchronized the first time successfully to a SNTP server.
I32 hm2SntpClientRequestInterval	1.3.6.1.4.1.248.11.50.1.2.3.4	Integer32	read-write	SNTP client request interval in seconds.
INT hm2SntpClientStatus	1.3.6.1.4.1.248.11.50.1.2.3.5	INTEGER	read-only	Overall operational status of the SNTP client.
I32 hm2SntpClientBroadcastRecvTimeout	1.3.6.1.4.1.248.11.50.1.2.3.6	Integer32	read-write	Time in seconds after the client in broadcast client mode will change the status from 'synchronizedToRemoteServer' to 'notSynchronized' if no broadcast packets are received.
hm2SntpClientServerAddrTable	1.3.6.1.4.1.248.11.50.1.2.3.10		not-accessible	This table contains objects to configure SNTP client connections.
hm2SntpClientServerAddrEntry	1.3.6.1.4.1.248.11.50.1.2.3.10.1		not-accessible	The SNTP client connection objects.
I32 hm2SntpClientServerIndex	1.3.6.1.4.1.248.11.50.1.2.3.10.1.1	Integer32	not-accessible	Index for server table.
IPt hm2SntpClientServerAddrType	1.3.6.1.4.1.248.11.50.1.2.3.10.1.2	InetAddressType	read-create	Address type.
IP hm2SntpClientServerAddr	1.3.6.1.4.1.248.11.50.1.2.3.10.1.3	InetAddress	read-create	The address of the external time server.
INE hm2SntpClientServerPort	1.3.6.1.4.1.248.11.50.1.2.3.10.1.4	InetPortNumber	read-create	The port number of the external time server.
STR hm2SntpClientServerDescr	1.3.6.1.4.1.248.11.50.1.2.3.10.1.5	DisplayString	read-create	The description of the server configured.
HMS hm2SntpClientServerStatus	1.3.6.1.4.1.248.11.50.1.2.3.10.1.6	HmSntpClientServerStatus	read-only	Status of the SNTP client - server connection.
ROW hm2SntpClientServerRowStatus	1.3.6.1.4.1.248.11.50.1.2.3.10.1.7	RowStatus	read-create	Indicates the status of an entry in this table, and is used to create/delete entries. Objects within this table can by changed while the status is 'active'.
hm2NtpGroup	1.3.6.1.4.1.248.11.50.1.3
hm2NtpGeneralGroup	1.3.6.1.4.1.248.11.50.1.3.1
INT hm2NtpOperatingState	1.3.6.1.4.1.248.11.50.1.3.1.1	INTEGER	read-only	Operational status of the NTP server/client.
hm2NtpServerGroup	1.3.6.1.4.1.248.11.50.1.3.2
hm2NtpServerConfigGroup	1.3.6.1.4.1.248.11.50.1.3.2.1
HME hm2NtpServerAdminState	1.3.6.1.4.1.248.11.50.1.3.2.1.1	HmEnabledStatus	read-write	Enables/disables the NTP server.
INT hm2NtpServerOperatingMode	1.3.6.1.4.1.248.11.50.1.3.2.1.2	INTEGER	read-write	NTP server operating mode.
I32 hm2NtpServerLocalClockStratum	1.3.6.1.4.1.248.11.50.1.3.2.1.3	Integer32	read-write	The stratum to be used for the case that the server is only synchronized to the local clock
hm2NtpClientGroup	1.3.6.1.4.1.248.11.50.1.3.3
hm2NtpClientConfigGroup	1.3.6.1.4.1.248.11.50.1.3.3.1
HME hm2NtpClientAdminState	1.3.6.1.4.1.248.11.50.1.3.3.1.1	HmEnabledStatus	read-write	Enables/disables the NTP client.
INT hm2NtpClientOperatingMode	1.3.6.1.4.1.248.11.50.1.3.3.1.2	INTEGER	read-write	NTP client operating mode.
hm2NtpClientServerAddrTable	1.3.6.1.4.1.248.11.50.1.3.3.4		not-accessible	This table contains variables for each interface of the switch.
hm2NtpClientServerAddrEntry	1.3.6.1.4.1.248.11.50.1.3.3.4.1		not-accessible	This entry contains variables for each interface of the switch.
I32 hm2NtpClientServerIndex	1.3.6.1.4.1.248.11.50.1.3.3.4.1.1	Integer32	not-accessible	Index for Server table.
IPt hm2NtpClientServerAddressType	1.3.6.1.4.1.248.11.50.1.3.3.4.1.2	InetAddressType	read-create	Address type for external time server. Currently, only IPv4 and DNS is supported.
IP hm2NtpClientServerAddress	1.3.6.1.4.1.248.11.50.1.3.3.4.1.3	InetAddress	read-create	The address of the external time server.
INE hm2NtpClientServerPort	1.3.6.1.4.1.248.11.50.1.3.3.4.1.4	InetPortNumber	read-create	The port number of the external time server. Zero is not allowed as port number.
HME hm2NtpClientServerInitialBurst	1.3.6.1.4.1.248.11.50.1.3.3.4.1.5	HmEnabledStatus	read-create	The initial burst is intended to speed up the initial synchronization. Use with caution as it can cause a overload situation on the server.
HME hm2NtpClientServerBurst	1.3.6.1.4.1.248.11.50.1.3.3.4.1.6	HmEnabledStatus	read-create	The burst mode can be used to increase the precision on links with high jitter e.g. GSM/UMTS links
T/F hm2NtpClientServerPrefer	1.3.6.1.4.1.248.11.50.1.3.3.4.1.7	TruthValue	read-create	The prefer flag can be used to mark the peer as preferred. Among a set of correctly operating peers, this one will be chosen as synchronization source.
INT hm2NtpClientServerStatus	1.3.6.1.4.1.248.11.50.1.3.3.4.1.10	INTEGER	read-only	Status of the NTP client server connection.
ROW hm2NtpClientServerRowStatus	1.3.6.1.4.1.248.11.50.1.3.3.4.1.11	RowStatus	read-create	Indicates the status of an entry in this table, and is used to create/delete entries. Objects within this table can be changed while the status is 'active'.
hm2NtpClientListenAddrTable	1.3.6.1.4.1.248.11.50.1.3.3.5		not-accessible	Client table.
hm2NtpClientListenAddrEntry	1.3.6.1.4.1.248.11.50.1.3.3.5.1		not-accessible	Client entry.
I32 hm2NtpClientListenAddrIndex	1.3.6.1.4.1.248.11.50.1.3.3.5.1.1	Integer32	not-accessible	Index for server table.
IPt hm2NtpClientListenAddrAddressType	1.3.6.1.4.1.248.11.50.1.3.3.5.1.2	InetAddressType	read-create	Address type for external time server. Currently, only IPv4 and DNS is supported.
IP hm2NtpClientListenAddrAddress	1.3.6.1.4.1.248.11.50.1.3.3.5.1.3	InetAddress	read-create	The address of the external time server.
INE hm2NtpClientListenAddrPort	1.3.6.1.4.1.248.11.50.1.3.3.5.1.4	InetPortNumber	read-create	The port number of the external time server. Zero is not allowed as port number.
INT hm2NtpClientListenAddrStatus	1.3.6.1.4.1.248.11.50.1.3.3.5.1.10	INTEGER	read-only	Status of the NTP client server connection.
ROW hm2NtpClientListenAddrRowStatus	1.3.6.1.4.1.248.11.50.1.3.3.5.1.11	RowStatus	read-create	Indicates the status of an entry in this table, and is used to create/delete entries. Objects within this table can by changed while the status is 'active'.
hm2PtpGroup	1.3.6.1.4.1.248.11.50.1.4
hm2PtpGlobal	1.3.6.1.4.1.248.11.50.1.4.1
HME hm2PtpEnable	1.3.6.1.4.1.248.11.50.1.4.1.1	HmEnabledStatus	read-write	Enable or disable the Precision Time Protocol (PTP) on this node.
INT hm2PtpClockMode	1.3.6.1.4.1.248.11.50.1.4.1.2	INTEGER	read-write	This members value shall indicate which clock mode is used.
INT hm2PtpProfile	1.3.6.1.4.1.248.11.50.1.4.1.3	INTEGER	read-write	Configures PTP parameters to a specific profile. Setting the object to user-defined (1) has no effect.
INT hm2PtpIsSynchronized	1.3.6.1.4.1.248.11.50.1.4.1.4	INTEGER	read-only	If the clock is synchronized to the current Master this object is set to true. Otherwise it is set to false. The clock sets this object to true, if the offset (ns) to the current Master is less than hm2PtpSyncLowerBound. The clock sets this object to false, if the offset (ns) to the current Master is bigger than hm2PtpSyncUpperBound.
I32 hm2PtpSyncLowerBound	1.3.6.1.4.1.248.11.50.1.4.1.5	Integer32	read-write	This object defines when the hm2PtpIsSynchronized object is set to true. If the absolute value of the offset is smaller than hm2PtpSyncLowerBound, the hm2PtpIsSynchronized is set true. The value is interpreted as nanoseconds.
I32 hm2PtpSyncUpperBound	1.3.6.1.4.1.248.11.50.1.4.1.6	Integer32	read-write	This object defines when the hm2PtpIsSynchronized object is set to false. If the absolute value of the offset is bigger than hm2PtpSyncUpperBound, the hm2PtpIsSynchronized is set false. The value is interpreted as nanoseconds.
I32 hm2PtpAbsMaxOffset	1.3.6.1.4.1.248.11.50.1.4.1.7	Integer32	read-only	This members value shall indicate the absolute value for the maximum offset between its parent and this node. The value is set to zero if the offset is the first time smaller than hm2PtpSyncLowerBound. Offsets bigger than +/-1 second are indicated by the maximum value.
PTP hm2PtpTimeSeconds	1.3.6.1.4.1.248.11.50.1.4.1.8	PtpTimeStamp	read-only	Current PTP time in PTP timescale
T/F hm2PtpManagement	1.3.6.1.4.1.248.11.50.1.4.1.9	TruthValue	read-write	If set to true PTP management via PTP management messages is enabled.
hm2Ptp2Objects	1.3.6.1.4.1.248.11.50.1.4.2
hm2Ptp2Configuration	1.3.6.1.4.1.248.11.50.1.4.2.1
T/F hm2Ptp2TwoStepClock	1.3.6.1.4.1.248.11.50.1.4.2.1.1	TruthValue	read-only	A value of true indicates that this node is a two-step device.
PTP hm2Ptp2ClockIdentity	1.3.6.1.4.1.248.11.50.1.4.2.1.2	PtpClockIdentity	read-only	This value is the clock identity of the local clock.
PTP hm2Ptp2ClockQuality	1.3.6.1.4.1.248.11.50.1.4.2.1.3	PtpClockQuality	read-only	Clock quality of the local clock.
I32 hm2Ptp2ClockClass	1.3.6.1.4.1.248.11.50.1.4.2.1.4	Integer32	read-only	First octet of hm2Ptp2ClockQuality. This represents the clock class of the local clock.
INT hm2Ptp2ClockAccuracy	1.3.6.1.4.1.248.11.50.1.4.2.1.5	INTEGER	read-only	Second octet of hm2Ptp2ClockQuality. This represents the clock accuracy of the local clock.
I32 hm2Ptp2ClockVariance	1.3.6.1.4.1.248.11.50.1.4.2.1.6	Integer32	read-only	Last two octets of hm2Ptp2ClockQuality. This represents the clock variance of the local clock.
I32 hm2Ptp2Priority1	1.3.6.1.4.1.248.11.50.1.4.2.1.7	Integer32	read-write	Priority 1 value of the local clock
I32 hm2Ptp2Priority2	1.3.6.1.4.1.248.11.50.1.4.2.1.8	Integer32	read-write	Priority 2 value of the local clock
I32 hm2Ptp2DomainNumber	1.3.6.1.4.1.248.11.50.1.4.2.1.9	Integer32	read-write	PTP domain number of the local clock.
I32 hm2Ptp2StepsRemoved	1.3.6.1.4.1.248.11.50.1.4.2.1.10	Integer32	read-only	The value of hm2Ptp2StepsRemoved is the number of communication paths traversed between the local clock and the grandmaster clock.
NUM hm2Ptp2OffsetFromMaster	1.3.6.1.4.1.248.11.50.1.4.2.1.11	PtpTimeInterval	read-only	Current value of the time difference between master and slave measured by this clock.
NUM hm2Ptp2MeanPathDelay	1.3.6.1.4.1.248.11.50.1.4.2.1.12	PtpTimeInterval	read-only	Current value of the mean propagation time (e2e-delay) between Master and Slave. This is only valid if hm2Ptp2DelayMechanism is set to e2e on the current slave port.
PTP hm2Ptp2ParentPortIdentity	1.3.6.1.4.1.248.11.50.1.4.2.1.13	PtpPortIdentity	read-only	The port identity value of the port on the master that issues the synchronization messages used to synchronize this clock.
T/F hm2Ptp2ParentStats	1.3.6.1.4.1.248.11.50.1.4.2.1.14	TruthValue	read-only	A value of True indicates that the objects hm2Ptp2ObservedParentOffsetScaledLogVariance and hm2Ptp2ObservedParentClockPhaseChangeRate are valid.
I32 hm2Ptp2ObservedParentOffsetScaledLogVariance	1.3.6.1.4.1.248.11.50.1.4.2.1.15	Integer32	read-only	Estimate of the parent clocks PTP variance observed by this clock.
I32 hm2Ptp2ObservedParentClockPhaseChangeRate	1.3.6.1.4.1.248.11.50.1.4.2.1.16	Integer32	read-only	Estimate of the phase change rate (drift) observed by this clock.
PTP hm2Ptp2GrandmasterIdentity	1.3.6.1.4.1.248.11.50.1.4.2.1.17	PtpClockIdentity	read-only	ClockIdentity of the Grandmaster clock synchronizing this clock.
PTP hm2Ptp2GrandmasterClockQuality	1.3.6.1.4.1.248.11.50.1.4.2.1.18	PtpClockQuality	read-only	ClockQuality of the Grandmaster clock synchronizing this clock.
I32 hm2Ptp2GrandmasterClockClass	1.3.6.1.4.1.248.11.50.1.4.2.1.19	Integer32	read-only	First octet of hm2Ptp2GrandmasterClockQuality. This represents the grand masters clock class.
INT hm2Ptp2GrandmasterClockAccuracy	1.3.6.1.4.1.248.11.50.1.4.2.1.20	INTEGER	read-only	Second octet of hm2Ptp2GrandmasterClockAccuracy. This represents the grand masters clock accuracy.
I32 hm2Ptp2GrandmasterClockVariance	1.3.6.1.4.1.248.11.50.1.4.2.1.21	Integer32	read-only	Last two octets of hm2Ptp2GrandmasterClockQuality. This represents the grand masters clock variance.
I32 hm2Ptp2GrandmasterPriority1	1.3.6.1.4.1.248.11.50.1.4.2.1.22	Integer32	read-only	Priority 1 value of the grand master clock.
I32 hm2Ptp2GrandmasterPriority2	1.3.6.1.4.1.248.11.50.1.4.2.1.23	Integer32	read-only	Priority 2 value of the grand master clock.
I32 hm2Ptp2CurrentUtcOffset	1.3.6.1.4.1.248.11.50.1.4.2.1.24	Integer32	read-write	Current difference between the PTP timescale (TAI) and UTC in seconds.
T/F hm2Ptp2CurrentUtcOffsetValid	1.3.6.1.4.1.248.11.50.1.4.2.1.25	TruthValue	read-write	A value of True indicates that the hm2Ptp2CurrentUtcOffset is known to be correct.
T/F hm2Ptp2Leap59	1.3.6.1.4.1.248.11.50.1.4.2.1.26	TruthValue	read-only	A value of true indicates that the last minute of the current UTC day contains 59 seconds.
T/F hm2Ptp2Leap61	1.3.6.1.4.1.248.11.50.1.4.2.1.27	TruthValue	read-only	A value of true indicates that the last minute of the current UTC day contains 61 seconds.
T/F hm2Ptp2TimeTraceable	1.3.6.1.4.1.248.11.50.1.4.2.1.28	TruthValue	read-only	A value of True indicates that the current time is traceable to a primary reference.
T/F hm2Ptp2FrequencyTraceable	1.3.6.1.4.1.248.11.50.1.4.2.1.29	TruthValue	read-only	A value of True indicates that the frequency determining the timescale is traceable to a primary reference.
T/F hm2Ptp2PtpTimescale	1.3.6.1.4.1.248.11.50.1.4.2.1.30	TruthValue	read-only	A value of True indicates that the clocks timescale is PTP.
INT hm2Ptp2TimeSource	1.3.6.1.4.1.248.11.50.1.4.2.1.31	INTEGER	read-write	The source of time used by the Grandmaster clock.
hm2Ptp2PortTable	1.3.6.1.4.1.248.11.50.1.4.2.2		not-accessible	This table contains variables for each PTP2 port of the switch.
hm2Ptp2PortEntry	1.3.6.1.4.1.248.11.50.1.4.2.2.1		not-accessible	Entry for one port.
HME hm2Ptp2PortEnable	1.3.6.1.4.1.248.11.50.1.4.2.2.1.1	HmEnabledStatus	read-write	Enable or disable the sending and receiving / processing of PTP synchronization messages.
INT hm2Ptp2PortState	1.3.6.1.4.1.248.11.50.1.4.2.2.1.2	INTEGER	read-only	State of the PTP2 port instance.
I32 hm2Ptp2LogDelayReqInterval	1.3.6.1.4.1.248.11.50.1.4.2.2.1.3	Integer32	read-only	Logarithm to the base of 2 of the minimum DelayRequest interval used to measure the e2e-delay.
NUM hm2Ptp2PeerMeanPathDelay	1.3.6.1.4.1.248.11.50.1.4.2.2.1.4	PtpTimeInterval	read-only	If hm2Ptp2DelayMechanism is set to p2p this value is an estimate of the current one-way propagation delay (p2p-delay).
INT hm2Ptp2LogAnnounceInterval	1.3.6.1.4.1.248.11.50.1.4.2.2.1.5	INTEGER	read-write	Logarithm to the base of 2 of the mean announce interval.
I32 hm2Ptp2AnnounceReceiptTimeout	1.3.6.1.4.1.248.11.50.1.4.2.2.1.6	Integer32	read-write	Announce receipt timeout in multiples of hm2Ptp2LogAnnounceInterval.
NUM hm2Ptp2LogSyncInterval	1.3.6.1.4.1.248.11.50.1.4.2.2.1.7	Hm2Ptp2LogSyncIntervalTc	read-write	Logarithm to the base of 2 of the mean synchronization interval.
INT hm2Ptp2DelayMechanism	1.3.6.1.4.1.248.11.50.1.4.2.2.1.8	INTEGER	read-write	This value indicates the propagation delay measuring option used by this port.
NUM hm2Ptp2LogPdelayReqInterval	1.3.6.1.4.1.248.11.50.1.4.2.2.1.9	Hm2Ptp2LogPdelayReqIntervalTc	read-write	Logarithm to the base of 2 of the minimum PDelay Request interval (used for p2p-delay).
INT hm2Ptp2VersionNumber	1.3.6.1.4.1.248.11.50.1.4.2.2.1.10	INTEGER	read-write	PTP version in use on this port (always ptpVersion2).
INT hm2Ptp2NetworkProtocol	1.3.6.1.4.1.248.11.50.1.4.2.2.1.11	INTEGER	read-write	Current configured network transport protocol of this port.
INT hm2Ptp2V1Compatibility	1.3.6.1.4.1.248.11.50.1.4.2.2.1.12	INTEGER	read-write	If set to on all PTPv2 messages will be padded to the length of a PTPv1 frame. This is required by some hardware.
I32 hm2Ptp2DelayAsymmetry	1.3.6.1.4.1.248.11.50.1.4.2.2.1.13	Integer32	read-write	Asymmetry of the link connected to this port in nanoseconds. The hm2Ptp2DelayAsymmetry is positive when the master-to-slave propagation time is longer than the slave-to-master propagation time.
BIT hm2Ptp2PortCapability	1.3.6.1.4.1.248.11.50.1.4.2.2.1.14	Bits	read-only	This object shows the capability of the ptp port.
I32 hm2Ptp2VlanID	1.3.6.1.4.1.248.11.50.1.4.2.2.1.15	Integer32	read-write	VLAN in which PTP packets are send. With a value of -1 all packets are send untagged
I32 hm2Ptp2VlanPriority	1.3.6.1.4.1.248.11.50.1.4.2.2.1.16	Integer32	read-write	VLAN priority of tagged ptp packets
hm2Ptp2TCObjects	1.3.6.1.4.1.248.11.50.1.4.3
hm2Ptp2TCConfiguration	1.3.6.1.4.1.248.11.50.1.4.3.1
PTP hm2Ptp2TCClockIdentity	1.3.6.1.4.1.248.11.50.1.4.3.1.1	PtpClockIdentity	read-only	This value is the clock identity of the transparent clock.
INT hm2Ptp2TCDelayMechanism	1.3.6.1.4.1.248.11.50.1.4.3.1.2	INTEGER	read-write	Configures the transparent clock to be either a e2e- or p2p-transparent clock. If supported a value of e2e-optimized sets the clock to e2e mode where delay requests are only forwarded on the port where the current Master (hm2Ptp2TCCurrentMaster) is connected.
I32 hm2Ptp2TCPrimaryDomain	1.3.6.1.4.1.248.11.50.1.4.3.1.3	Integer32	read-write	PTP domain number of the primary syntonization domain.
T/F hm2Ptp2TCSyntonized	1.3.6.1.4.1.248.11.50.1.4.3.1.4	TruthValue	read-write	A value of true indicates that the syntonization of the transparent clock is enabled.
INT hm2Ptp2TCNetworkProtocol	1.3.6.1.4.1.248.11.50.1.4.3.1.5	INTEGER	read-write	Current configured network transport protocol of the transparent clock.
PTP hm2Ptp2TCCurrentMaster	1.3.6.1.4.1.248.11.50.1.4.3.1.6	PtpPortIdentity	read-only	The port identity value of the port on the master that issues the synchronization messages used to syntonize/synchronize this clock.
T/F hm2Ptp2TCMultiDomainMode	1.3.6.1.4.1.248.11.50.1.4.3.1.7	TruthValue	read-write	If set to false, PTP messages from domains other than hm2Ptp2TCPrimaryDomain are ignored.
T/F hm2Ptp2TCSyncLocalClock	1.3.6.1.4.1.248.11.50.1.4.3.1.8	TruthValue	read-write	Enable synchronisation of the local clock (TC hybrid mode). This requires syntonization to be enabled. All transparent clock operations are still done based on the syntonized clock.
NUM hm2Ptp2TCOffsetFromMaster	1.3.6.1.4.1.248.11.50.1.4.3.1.9	PtpTimeInterval	read-only	Current value of the time difference between Master and this clock measured by this clock. This object is only valid if hm2Ptp2TCSyncLocalClock is set to true.
NUM hm2Ptp2TCMeanPathDelay	1.3.6.1.4.1.248.11.50.1.4.3.1.10	PtpTimeInterval	read-only	Current value of the mean propagation time (e2e-delay) between Master and Slave. This object is only valid for e2e-transparent-clock and hm2Ptp2TCSyncLocalClock is set to true.
I32 hm2Ptp2TCVlanID	1.3.6.1.4.1.248.11.50.1.4.3.1.11	Integer32	read-write	VLAN in which PTP packets are send. With a value of -1 all packets are send untagged.
I32 hm2Ptp2TCVlanPriority	1.3.6.1.4.1.248.11.50.1.4.3.1.12	Integer32	read-write	VLAN priority of tagged PTP packets.
BIT hm2Ptp2TCCapability	1.3.6.1.4.1.248.11.50.1.4.3.1.13	Bits	read-only	This object shows the capability of the TC.
hm2Ptp2TCPortTable	1.3.6.1.4.1.248.11.50.1.4.3.2		not-accessible	This table contains variables for each PTP2 TC port of the switch.
hm2Ptp2TCPortEntry	1.3.6.1.4.1.248.11.50.1.4.3.2.1		not-accessible	Entry for one port.
HME hm2Ptp2TCPortEnable	1.3.6.1.4.1.248.11.50.1.4.3.2.1.1	HmEnabledStatus	read-write	Enable or disable the sending and receiving / processing of PTP synchronization messages.
NUM hm2Ptp2TCLogPdelayReqInterval	1.3.6.1.4.1.248.11.50.1.4.3.2.1.2	Hm2Ptp2LogPdelayReqIntervalTc	read-write	Logarithm to the base of 2 of the minimum PDelay Request interval (used for p2p-delay).
T/F hm2Ptp2TCFaulty	1.3.6.1.4.1.248.11.50.1.4.3.2.1.3	TruthValue	read-only	True if port is in Faulty state.
NUM hm2Ptp2TCPeerMeanPathDelay	1.3.6.1.4.1.248.11.50.1.4.3.2.1.4	PtpTimeInterval	read-only	This value is an estimate of the current one way propagation delay of a p2p-transparent-clock.
I32 hm2Ptp2TCDelayAsymmetry	1.3.6.1.4.1.248.11.50.1.4.3.2.1.5	Integer32	read-write	Asymmetry of the link connected to this port in nanoseconds. The hm2Ptp2TCDelayAsymmetry is positive when the master-to-slave propagation time is longer than the slave-to-master propagation time.
hm2IrigGroup	1.3.6.1.4.1.248.11.50.1.5
HME hm2IrigAdminStatus	1.3.6.1.4.1.248.11.50.1.5.1	HmEnabledStatus	read-write	Enables/disables the IRIG-B output.
INT hm2IrigMode	1.3.6.1.4.1.248.11.50.1.5.2	INTEGER	read-write	Set the IRIG Mode, allowed values: (See https://wsmrc2vger.wsmr.army.mil/rcc/manuals/200-04/TT-45.pdf) irig-b000 (0) - Mode IRIG B000, BCDtoy, CF, SBS irig-b001 (1) - Mode IRIG B001, BCDtoy, CF irig-b002 (2) - Mode IRIG B002, BCDtoy irig-b003 (3) - Mode IRIG B003, BCDtoy, SBS irig-b004 (4) - Mode IRIG B004, BCDtoy, BCDyear, CF, SBS irig-b005 (5) - Mode IRIG B005, BCDtoy, BCDyear, CF irig-b006 (6) - Mode IRIG B006, BCDtoy, BCDyear irig-b007 (7) - Mode IRIG B007, BCDtoy, BCDyear, SBS with BCDtoy: binary coded decimal time of year BCDyear: binary coded decimal year CF: control functions SBS: straight binary seconds of day only modes b002,B003,B006 and b007 are supported.
HME hm2IrigPpsAdminStatus	1.3.6.1.4.1.248.11.50.1.5.3	HmEnabledStatus	read-write	Enables/disables the pps output.
INT hm2IrigTimeMode	1.3.6.1.4.1.248.11.50.1.5.4	INTEGER	read-write	Define the IRIG-B time base (UTC or local).
HME hm2IrigOperStatus	1.3.6.1.4.1.248.11.50.1.5.5	HmEnabledStatus	read-only	Current operational status of the IRIG-B output.
INT hm2IrigTimeQuality	1.3.6.1.4.1.248.11.50.1.5.6	INTEGER	read-only	Current IRIG-B time quality according to IEEE 1344.
hm2TimeSyncMibSNMPExtensionGroup	1.3.6.1.4.1.248.11.50.3
hm2TimeSyncSystemTimeSESGroup	1.3.6.1.4.1.248.11.50.3.1
hm2TimeSyncSntpSESGroup	1.3.6.1.4.1.248.11.50.3.2
hm2TimeSyncSntpSESIpv4PortNumberPairInUse	1.3.6.1.4.1.248.11.50.3.2.1			Indicates that the given IPv4 address / port number combination is already in use.
hm2TimeSyncSntpSESDnsPortNumberPairInUse	1.3.6.1.4.1.248.11.50.3.2.2			Indicates that the given DNS name / port number combination is already in use.
hm2TimeSyncNtpSESGroup	1.3.6.1.4.1.248.11.50.3.3
hm2TimeSyncPtpSESGroup	1.3.6.1.4.1.248.11.50.3.4
hm2TimeSyncIrigSESGroup	1.3.6.1.4.1.248.11.50.3.5

RFC description

Harmonic vendor-private MIB for managing time synchronization, NTP, and clock distribution in Media Platform systems.

Start monitoring Hirschmann HiOS industrial Ethernet switch (NTP/SNTP/PTP time sync) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HM2-TIMESYNC-MIB