F3-SYNC-MIB

All MIBs › F3-SYNC-MIB

Organization: ADVA Optical Networking SE

Last Updated: 2020-01-15

Category: Domain: Telco/Transport, Technology: Optical Transport, Technology: Time Synchronization, Vendor: ADVA Optical

Description: ADVA Optical Networking F3 platform MIB for synchronization source management including SyncE and timing references.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is F3-SYNC-MIB?

F3-SYNC-MIB is an ADVA Optical Networking proprietary MIB for the FSP 3000 (F3) platform, managing synchronization and timing objects including SyncE, network clock references, and (in later revisions) precision clock-phase/offset adjustments. It exposes configuration data (admin state, selected reference, clock mode, protection-group membership) alongside operational/status data (operational state, secondary state, quality level) for each timing source. Each F3-SYNC-MIB OID in this family, such as f3SyncOperationalState and f3SyncSecondaryState, directly supports monitoring the operational health of timing distribution hardware by revealing whether a clock source is locked, in holdover, or degraded, while the added clock-phase/offset objects monitor drift and jump events critical to network timing accuracy. As an ADVA platform MIB it is used alongside other F3-series MIBs covering the same optical network elements. It is typically deployed on ADVA FSP 3000 optical transport platforms requiring precise synchronization, e.g. mobile backhaul with SyncE/timing distribution.

IPNetwork Monitor allows you to monitor SNMP objects defined in F3-SYNC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADVA Optical Networking FSP150CM/CC (F3 platform) carrier Ethernet device (SyncE/timing synchronization) — Identified via cross-reference against the module's own release notes ('MIB version ready for release of FSP150CC devices GE101 and GE206') and its F3-PTP-MIB/F3-SYNCJACK-MIB sibling dependencies, all of which are FSP150CM/CC (F3) platform modules; the previous description's 'FSP 3000 R8'/'FSP 3000 OLS' DWDM optical transport attribution was incorrect — FSP 3000 is an unrelated ADVA product line.

Monitoring Examples

f3SyncTable/f3SyncEntry, indexed by f3SyncIndex, expose f3SyncAdminState and f3SyncOperationalState so an admin can confirm a timing source is enabled and operationally locked; f3SyncSecondaryState gives finer-grained status such as holdover or free-run for diagnosing timing degradation. f3SyncSelectedReference and f3SyncQL show which reference the clock has selected and its quality level, letting an operator catch an unwanted reference switch. f3SyncClockMode and f3SyncNetworkClockType describe the synchronization mode (e.g. SyncE) in use, and f3SyncDomain groups timing objects by synchronization domain on larger platforms.

What Can Be Monitored

sync source admin state
sync source operational state
secondary/holdover state
selected clock reference
clock quality level (QL)
synchronization domain/protection group membership

Imported Objects

From ADVA-MIB

fsp150cm

OBJECT-IDENTITY

From CM-COMMON-MIB

AdminState
F3DisplayString
OperationalState
RestartType
SecondaryState

From CM-ENTITY-MIB

neIndex	OBJECT-TYPE
shelfIndex	OBJECT-TYPE
slotIndex	OBJECT-TYPE

From CM-REDUNDANCY-MIB

CmGenPgSwitchoverReason

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
StorageType
TEXTUAL-CONVENTION
TruthValue
VariablePointer

How to Use in IPNetwork Monitor

Example using f3TimeClockAtoiCurrentOffset OID:

Select an ADVA Optical Networking FSP150 (F3 platform) carrier Ethernet device as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type f3TimeClockAtoiCurrentOffset into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the current offset, in seconds, of this node's alternate time-of-day reference from the node's own clock. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the offset drifts away from zero beyond the tolerance your timing plan allows, since a growing clock offset indicates a synchronization problem. Click Finish to create the monitor; you can adjust any parameter later.

See also: f3TimeClockTimeInHoldover

OIDs

OID symbolic	OID numeric	Type	Access	Description
I32 f3PrcAccuracyAdjustement	1.3.6.1.4.1.2544.1.12.12.1.5.1.8	Integer32	read-write	This object allows to adjust an internal frequency to optimize the PRC accuracy. This is typically done only once after the Prc has been tested. The value is a relative frequency with unit value of 10e-15.
ACK f3PrcAcknowledgeAction	1.3.6.1.4.1.2544.1.12.12.1.5.1.10	AcknowledgeType	read-write	Allows to acknowledge the alarm that raises when f3AccuracyAdjustement value is changed.
ADM f3PrcAdminState	1.3.6.1.4.1.2544.1.12.12.1.5.1.3	AdminState	read-write	This object represents the Administrative State of the Primary Reference Clock Entity.
STR f3PrcAlias	1.3.6.1.4.1.2544.1.12.12.1.5.1.2	F3DisplayString	read-write	This object allows SNMP management entities to provide an alias to the Primary Reference Clock entity.
TIM f3PrcClockMode	1.3.6.1.4.1.2544.1.12.12.1.5.1.7	TimeClockMode	read-only	This object provides the PRC Clock Mode.
SSM f3PrcCurrentQL	1.3.6.1.4.1.2544.1.12.12.1.5.1.9	SSMQualityLevel	read-only	This object describe the current quality level.
f3PrcEntry	1.3.6.1.4.1.2544.1.12.12.1.5.1		not-accessible	An entry containing information applicable to a particular Primary Reference Clock Entity.
I32 f3PrcIndex	1.3.6.1.4.1.2544.1.12.12.1.5.1.1	Integer32	not-accessible	Unique index value associated with the Primary Reference Clock Entity.
f3PrcObjectGroup	1.3.6.1.4.1.2544.1.12.12.2.2.3			A collection of objects used to manage the F3 Primary Reference Clock Object group.
OPE f3PrcOperationalState	1.3.6.1.4.1.2544.1.12.12.1.5.1.4	OperationalState	read-only	This object represents the Operational State of the Primary Reference Clock Entity.
RES f3PrcRestartAction	1.3.6.1.4.1.2544.1.12.12.1.5.1.11	RestartType	read-write	Allows to perform specified warm restart action on the PRC Clock. Cold restart is refused by the equipment
SEC f3PrcSecondaryState	1.3.6.1.4.1.2544.1.12.12.1.5.1.5	SecondaryState	read-only	This object represents the Secondary State of the Primary Reference Clock Entity.
SSM f3PrcSsmMode	1.3.6.1.4.1.2544.1.12.12.1.5.1.6	SsmMode	read-write	This object provides the PRC SSM mode. It determines whether or not the SSM is given to the BITS-OUT Ports.
f3PrcTable	1.3.6.1.4.1.2544.1.12.12.1.5		not-accessible	A list of entries corresponding to the Primary Reference Clock (PRC) entities.
f3ProtObjectGroup	1.3.6.1.4.1.2544.1.12.12.2.2.4			A collection of objects used to manage the Protection Object group.
ADM f3SyncAdminState	1.3.6.1.4.1.2544.1.12.12.1.1.1.2	AdminState	read-write	This object represents the Administrative State of the Sync Entity.
STR f3SyncAlias	1.3.6.1.4.1.2544.1.12.12.1.1.1.9	DisplayString	read-create	This object allows SNMP management entities to provide an alias to the Sync entity.
CLO f3SyncClockMode	1.3.6.1.4.1.2544.1.12.12.1.1.1.7	ClockMode	read-only	This object provides the system clock mode.
f3SyncCompliance	1.3.6.1.4.1.2544.1.12.12.2.1.1			Describes the requirements for conformance to the F3 Sync group.
f3SyncCompliances	1.3.6.1.4.1.2544.1.12.12.2.1
f3SyncConformance	1.3.6.1.4.1.2544.1.12.12.2
NUM f3SyncDomain	1.3.6.1.4.1.2544.1.12.12.1.1.1.10	SyncDomainType	read-write	This object represents the Sync entity's domain type. A Sync entity can be in chassis (system) domain (applicable for HUB shelf and Aggregation shelf) or line card domain (applicable for HUB shelf, Aggregation shelf as well as NIDs).
f3SyncEntry	1.3.6.1.4.1.2544.1.12.12.1.1.1		not-accessible	An entry containing information applicable to a particular Sync Entity.
f3SyncGroups	1.3.6.1.4.1.2544.1.12.12.2.2
I32 f3SyncIndex	1.3.6.1.4.1.2544.1.12.12.1.1.1.1	Integer32	read-only	Unique index value associated with the Synchronization Entity.
f3SyncMIB	1.3.6.1.4.1.2544.1.12.12			Notes from release 202001150000Z (1) Added f3TimeClockPhaseAdjust Notes from release 201909110000Z, (1) New textual conventions: ClkSignalType Notes from release 201907080000Z, (1) Added f3TimeClockAtoiCurrentOffset, f3TimeClockAtoiJumpSeconds, f3TimeClockAtoiTimeOfNextJump, f3TimeClockAtoiDisplayName Notes from release 201901230000Z, (1) Added table indices: f3SyncProtGroupIndex in f3SyncProtMemberEntry, f3TimeClockProtGroupIndex in f3TimeClockProtMemberEntry Notes from release 201807300000Z, (1) New tables: f3SyncProtGroupTable, f3SyncProtMemberTable, f3TimeClockProtGroupTable, f3TimeClockProtMemberTable Notes from release 201901070000Z (1) Added f3TimeClockTimeHoldoverTimeout (2) Added f3TimeClockTimeInHoldover Notes from release 201802210000Z, (1) Added table: f3PrcTable (2) New textual conventions: SsmMode and AcknowledgeType Notes from release 201304240000Z, (1) New tables: f3TimeClockTable, f3TimeClockRefTable Notes from release 201003250000Z, (1)f3SyncTable has new objects f3SyncSelectionMode, f3SyncWaitToRestoreTime, f3SyncOperationSyncRef, f3SyncOperationType, (2)f3SyncRefTable has new object f3SyncRefOperationType Notes from release 201002120000Z, (1)f3SyncTable has new objects f3SyncAlias, f3SyncDomain (2)f3SyncRefTable has new objects f3SyncRefAlias, f3SyncRefEffectiveQL Notes from release 200903190000Z, (1)MIB version ready for release of FSP150CC devices GE101 and GE206.
NET f3SyncNetworkClockType	1.3.6.1.4.1.2544.1.12.12.1.1.1.5	NetworkClockType	read-write	This object represents the regional clock type for the system. This object determines which QL codes are supported.
f3SyncObjectGroup	1.3.6.1.4.1.2544.1.12.12.2.2.1			A collection of objects used to manage the F3 Sync Object group.
f3SyncObjects	1.3.6.1.4.1.2544.1.12.12.1
OPE f3SyncOperationalState	1.3.6.1.4.1.2544.1.12.12.1.1.1.3	OperationalState	read-only	This object represents the Operational State of the Sync Entity.
NUM f3SyncOperationSyncRef	1.3.6.1.4.1.2544.1.12.12.1.1.1.13	VariablePointer	read-write	This object allows configuration of the Object Identifier of the Sync Reference Entity on which the f3SyncOperationType is performed. A value of 0.0 denotes no sync reference is chosen for operation.
SYN f3SyncOperationType	1.3.6.1.4.1.2544.1.12.12.1.1.1.14	SyncOperationType	read-write	This object allows to perform the specified operation on the Sync Reference specified by f3SyncOperationSyncRef.
PLL f3SyncPLLBw	1.3.6.1.4.1.2544.1.12.12.1.1.1.15	PLLBw	read-write	This object allows configuration of the Sync entity's Clock PLL Bandwidth.
NUM f3SyncProtGroupActiveMember	1.3.6.1.4.1.2544.1.12.12.1.6.1.3	VariablePointer	read-only	The corresponding OID of the Active Member in the Sync Protection Group.
ADM f3SyncProtGroupAdminState	1.3.6.1.4.1.2544.1.12.12.1.6.1.2	AdminState	read-write	This object represents the Administrative State of the Sync Protection Group.
f3SyncProtGroupEntry	1.3.6.1.4.1.2544.1.12.12.1.6.1		not-accessible	An entry containing information applicable to a Sync Protection Group.
I32 f3SyncProtGroupIndex	1.3.6.1.4.1.2544.1.12.12.1.6.1.1	Integer32	read-only	Unique index value associated with the Sync Protection Group entity.
CMG f3SyncProtGroupLastSwitchOverReason	1.3.6.1.4.1.2544.1.12.12.1.6.1.5	CmGenPgSwitchoverReason	read-only	The reason for last switch over in the Sync Protection Group.
TIK f3SyncProtGroupLastSwitchOverTime	1.3.6.1.4.1.2544.1.12.12.1.6.1.4	TimeTicks	read-only	The value of sysUpTime when last switch over occurred.
ROW f3SyncProtGroupRowStatus	1.3.6.1.4.1.2544.1.12.12.1.6.1.7	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3SyncProtGroupRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3SyncProtGroupRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3SyncProtGroupRowStatus object may be modified if the associated instance of this object is equal to active(1).
STO f3SyncProtGroupStorageType	1.3.6.1.4.1.2544.1.12.12.1.6.1.6	StorageType	read-create	The type of storage configured for this entry.
f3SyncProtGroupTable	1.3.6.1.4.1.2544.1.12.12.1.6		not-accessible	A list of entries corresponding to the Sync Protection Groups.
f3SyncProtMemberEntry	1.3.6.1.4.1.2544.1.12.12.1.7.1		not-accessible	A conceptual row in the f3SyncProtMemberTable.
NUM f3SyncProtMemberObject	1.3.6.1.4.1.2544.1.12.12.1.7.1.1	VariablePointer	not-accessible	This object points to the Protection Group Member.
ROW f3SyncProtMemberRowStatus	1.3.6.1.4.1.2544.1.12.12.1.7.1.3	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3SyncProtMemberRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3SyncProtMemberRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3SyncProtMemberRowStatus object may be modified if the associated instance of this object is equal to active(1).
STO f3SyncProtMemberStorageType	1.3.6.1.4.1.2544.1.12.12.1.7.1.2	StorageType	read-create	The type of storage configured for this entry.
f3SyncProtMemberTable	1.3.6.1.4.1.2544.1.12.12.1.7		not-accessible	A list of entries for the Sync Protection Group Members.
SSM f3SyncQL	1.3.6.1.4.1.2544.1.12.12.1.1.1.8	SSMQualityLevel	read-only	This object provides the QL of the system reference. This is the value for each external reference's Transmit QL attribute unless it should be transmitting QL-DNU.
STR f3SyncRefAlias	1.3.6.1.4.1.2544.1.12.12.1.2.1.9	DisplayString	read-create	This object allows SNMP management entities to provide an alias to the Sync Reference entity.
SSM f3SyncRefEffectiveQL	1.3.6.1.4.1.2544.1.12.12.1.2.1.10	SSMQualityLevel	read-only	This object provides the sync reference effective QL.
f3SyncRefEntry	1.3.6.1.4.1.2544.1.12.12.1.2.1		not-accessible	An entry containing information applicable to a particular Sync Reference Entity.
I32 f3SyncRefIndex	1.3.6.1.4.1.2544.1.12.12.1.2.1.1	Integer32	read-only	Unique index value associated with the Sync Reference Entity.
SYN f3SyncRefOperationType	1.3.6.1.4.1.2544.1.12.12.1.2.1.11	SyncOperationType	read-only	This object provides information on the current/active operation on this sync reference.
I32 f3SyncRefPriority	1.3.6.1.4.1.2544.1.12.12.1.2.1.3	Integer32	read-create	This object represents the priority of the external sync reference to be used as system clock reference source. This value is not mandatory when a single clock reference source is supported. Lower priority value indicates higher priority.
SSM f3SyncRefReceivedQL	1.3.6.1.4.1.2544.1.12.12.1.2.1.6	SSMQualityLevel	read-only	This object provides the sync reference received QL.
NUM f3SyncRefReference	1.3.6.1.4.1.2544.1.12.12.1.2.1.2	VariablePointer	read-create	This object represents the external sync reference to be used as system clock reference source.
ROW f3SyncRefRowStatus	1.3.6.1.4.1.2544.1.12.12.1.2.1.8	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3SyncRefRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3SyncRefRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3SyncRefRowStatus object may be modified if the associated instance of this object is equal to active(1).
SYN f3SyncRefState	1.3.6.1.4.1.2544.1.12.12.1.2.1.5	SyncRefState	read-only	This object provides the sync reference state.
SYN f3SyncRefStatus	1.3.6.1.4.1.2544.1.12.12.1.2.1.4	SyncRefStatus	read-only	This object provides the sync reference status.
STO f3SyncRefStorageType	1.3.6.1.4.1.2544.1.12.12.1.2.1.7	StorageType	read-create	The type of storage configured for this entry.
f3SyncRefTable	1.3.6.1.4.1.2544.1.12.12.1.2		not-accessible	A list of entries corresponding to the Sync Reference entities.
SEC f3SyncSecondaryState	1.3.6.1.4.1.2544.1.12.12.1.1.1.4	SecondaryState	read-only	This object represents the Secondary State of the Sync Entity.
NUM f3SyncSelectedReference	1.3.6.1.4.1.2544.1.12.12.1.1.1.6	VariablePointer	read-only	This object provides the source of the currently selected Sync reference. This would be the OID of the actual entity (bits port, traffic port etc.). An OID value of {0 0} represents internal clock.
SYN f3SyncSelectionMode	1.3.6.1.4.1.2544.1.12.12.1.1.1.11	SyncSelectionMode	read-write	This object represents the Sync entity's selection mode. If this mode is configured as ql-mode, the selection of which reference should be used shall be based upon the reference's Quality Level. The highest received Quality Level shall be the selected reference. The priority shall only be used to distinguish between references with the same received QL. When multiple references have the same QL and same priority, the behavior of selection process within the group is non-revertive. If this mode is configued as priority-mode, the selection of which reference should be used shall be based upon the reference's priority (i.e. QL is disabled). When multiple references have the same priority, the behavior of selection process within the group is non-revertive.
f3SyncTable	1.3.6.1.4.1.2544.1.12.12.1.1		not-accessible	A list of entries corresponding to the Sync entities.
I32 f3SyncWaitToRestoreTime	1.3.6.1.4.1.2544.1.12.12.1.1.1.12	Integer32	read-write	This object allows configuration of the Sync entity's wait-to-restore time (in minutes). A value of 0 disables WTR timers for all references.
ADM f3TimeClockAdminState	1.3.6.1.4.1.2544.1.12.12.1.3.1.3	AdminState	read-write	This object represents the Administrative State of the Time Clock Entity.
STR f3TimeClockAlias	1.3.6.1.4.1.2544.1.12.12.1.3.1.2	F3DisplayString	read-write	This object allows SNMP management entities to provide an alias to the Time Clock entity.
I32 f3TimeClockAtoiCurrentOffsetEx	1.3.6.1.4.1.2544.1.12.12.1.3.1.29	Integer32	read-only	The value of currentOffset (offset of the alternate time, in seconds, from the time of this node). The alternate time is the sum of this value and the time of the node, which is TAI if the PTP time scale is used.
STR f3TimeClockAtoiDisplayName	1.3.6.1.4.1.2544.1.12.12.1.3.1.32	DisplayString	read-only	The value of displayName (text name of the alternate timescale in ASCII-8). It represent the time zone, e.g. CET; a leading character of * indicates that daylight saving time is in effect.
I32 f3TimeClockAtoiJumpSeconds	1.3.6.1.4.1.2544.1.12.12.1.3.1.30	Integer32	read-only	The value of jumpSeconds (size of the next discontinuity, in seconds, of the alternate time). A value of zero indicates that no discontinuity is expected. A positive value indicates that the discontinuity will cause the currentOffset of the alternate time to increase.
C64 f3TimeClockAtoiTimeOfNextJump	1.3.6.1.4.1.2544.1.12.12.1.3.1.31	Counter64	read-only	The value of timeOfNextJump (value of the seconds portion of the time of the transmitting node at the time that the next discontinuity will occur). The discontinuity occurs at the start of the second indicated by the value of timeOfNextJump.
U32 f3TimeClockClockClass	1.3.6.1.4.1.2544.1.12.12.1.3.1.8	Unsigned32	read-only	This object provides the Time Clock Clock Class
TIM f3TimeClockClockMode	1.3.6.1.4.1.2544.1.12.12.1.3.1.7	TimeClockMode	read-only	This object provides the Time Clock mode.
SSM f3TimeClockCurrentQL	1.3.6.1.4.1.2544.1.12.12.1.3.1.17	SSMQualityLevel	read-only	This object describe the current quality level.
DAT f3TimeClockCurrentTimeOfDay	1.3.6.1.4.1.2544.1.12.12.1.3.1.21	DateAndTime	read-only	This object allows specification of the Time Clock Current Time of Day.
f3TimeClockEntry	1.3.6.1.4.1.2544.1.12.12.1.3.1		not-accessible	An entry containing information applicable to a particular Time Clock Entity.
T/F f3TimeClockEPRTCModeEnabled	1.3.6.1.4.1.2544.1.12.12.1.3.1.26	TruthValue	read-write	This object describe whether it is EPRTC Mode Enabled. When enabled, the time clock combines the stable frequency input, such as a Cesium Clock, to extend the holdover capability to meet the e-PRTC holdover standards. Before configuring this setting, ensure that you activate the e-PRTC license. Note: This setting is applicable for Rb/HQ++ oscillators only.
SSM f3TimeClockExpectedQL	1.3.6.1.4.1.2544.1.12.12.1.3.1.16	SSMQualityLevel	read-write	This object describe the expected quality level.
CLO f3TimeClockFrequencyClockMode	1.3.6.1.4.1.2544.1.12.12.1.3.1.23	ClockMode	read-only	This object provides the Frequency Clock mode determined according to the used f3TimeClockFrequencyReference. In Case the f3TimeClockFrequencyReference is not selected (0.0), a 'notAvailable' value shall be used here
NUM f3TimeClockFrequencyReference	1.3.6.1.4.1.2544.1.12.12.1.3.1.22	VariablePointer	read-write	This object provides the source of the currently selected frequency source for the Time Clock. This would be the OID of the actual entity (GNSS Receiver port, Input Frquency Port, Sync object). An OID value of {0.0} represents a state where the Time Clock does not use a dedicated frequency input.
I32 f3TimeClockIndex	1.3.6.1.4.1.2544.1.12.12.1.3.1.1	Integer32	not-accessible	Unique index value associated with the Time Clock Entity.
T/F f3TimeClockLeap59	1.3.6.1.4.1.2544.1.12.12.1.3.1.13	TruthValue	read-only	True if last minute of current UTC day contains 59 seconds, else false
T/F f3TimeClockLeap61	1.3.6.1.4.1.2544.1.12.12.1.3.1.14	TruthValue	read-only	True if last minute of current UTC day contains 61 seconds, else false
f3TimeClockObjectGroup	1.3.6.1.4.1.2544.1.12.12.2.2.2			A collection of objects used to manage the F3 TimeClock Object group.
OPE f3TimeClockOperationalState	1.3.6.1.4.1.2544.1.12.12.1.3.1.4	OperationalState	read-only	This object represents the Operational State of the Time Clock Entity.
NUM f3TimeClockOperationTimeClockRef	1.3.6.1.4.1.2544.1.12.12.1.3.1.11	VariablePointer	read-write	This object allows configuration of the Object Identifier of the TimeClock Reference Entity on which the f3TimeClockOperationType is performed. A value of 0.0 denotes no Time Clock reference is chosen for operation.
SYN f3TimeClockOperationType	1.3.6.1.4.1.2544.1.12.12.1.3.1.12	SyncOperationType	read-write	This object allows to perform the specified operation on the Time Clock Reference specified by f3TimeClockOperationTimeClockRef.
I32 f3TimeClockPhaseAdjust	1.3.6.1.4.1.2544.1.12.12.1.3.1.33	Integer32	read-write	Configurable Phase Adjust (0..250000 nSec) .
NUM f3TimeClockProtGroupActiveMember	1.3.6.1.4.1.2544.1.12.12.1.8.1.3	VariablePointer	read-only	The corresponding OID of the Active Member in the Time Clock Protection Group.
ADM f3TimeClockProtGroupAdminState	1.3.6.1.4.1.2544.1.12.12.1.8.1.2	AdminState	read-write	This object represents the Administrative State of the Time Clock Protection Group.
f3TimeClockProtGroupEntry	1.3.6.1.4.1.2544.1.12.12.1.8.1		not-accessible	An entry containing information applicable to a Time Clock Protection Group.
I32 f3TimeClockProtGroupIndex	1.3.6.1.4.1.2544.1.12.12.1.8.1.1	Integer32	read-only	Unique index value associated with the Time Clock Protection Group entity.
CMG f3TimeClockProtGroupLastSwitchOverReason	1.3.6.1.4.1.2544.1.12.12.1.8.1.5	CmGenPgSwitchoverReason	read-only	The reason for last switch over in the Time Clock Redundancy Group.
TIK f3TimeClockProtGroupLastSwitchOverTime	1.3.6.1.4.1.2544.1.12.12.1.8.1.4	TimeTicks	read-only	The value of sysUpTime when last switch over occurred.
ROW f3TimeClockProtGroupRowStatus	1.3.6.1.4.1.2544.1.12.12.1.8.1.7	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3TimeClockProtGroupRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3TimeClockProtGroupRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3TimeClockProtGroupRowStatus object may be modified if the associated instance of this object is equal to active(1).
STO f3TimeClockProtGroupStorageType	1.3.6.1.4.1.2544.1.12.12.1.8.1.6	StorageType	read-create	The type of storage configured for this entry.
f3TimeClockProtGroupTable	1.3.6.1.4.1.2544.1.12.12.1.8		not-accessible	A list of entries corresponding to the Time Clock Protection Groups.
f3TimeClockProtMemberEntry	1.3.6.1.4.1.2544.1.12.12.1.9.1		not-accessible	A conceptual row in the f3TimeClockProtMemberTable.
NUM f3TimeClockProtMemberObject	1.3.6.1.4.1.2544.1.12.12.1.9.1.1	VariablePointer	not-accessible	This object points to the Protection Group Member.
ROW f3TimeClockProtMemberRowStatus	1.3.6.1.4.1.2544.1.12.12.1.9.1.3	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3TimeClockProtMemberRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3TimeClockProtMemberRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3TimeClockProtMemberRowStatus object may be modified if the associated instance of this object is equal to active(1).
STO f3TimeClockProtMemberStorageType	1.3.6.1.4.1.2544.1.12.12.1.9.1.2	StorageType	read-create	The type of storage configured for this entry.
f3TimeClockProtMemberTable	1.3.6.1.4.1.2544.1.12.12.1.9		not-accessible	A list of entries for the Time Clock Protection Group Members.
STR f3TimeClockRefAlias	1.3.6.1.4.1.2544.1.12.12.1.4.1.2	F3DisplayString	read-create	This object allows SNMP management entities to provide an alias to the Time Clock Reference entity.
f3TimeClockRefEntry	1.3.6.1.4.1.2544.1.12.12.1.4.1		not-accessible	An entry containing information applicable to a particular Time Clock Reference Entity.
I32 f3TimeClockRefIndex	1.3.6.1.4.1.2544.1.12.12.1.4.1.1	Integer32	not-accessible	Unique index value associated with the Time Clock Reference Entity.
SYN f3TimeClockRefOperationType	1.3.6.1.4.1.2544.1.12.12.1.4.1.7	SyncOperationType	read-only	This object provides information on the current/active operation on this Time Clock reference.
I32 f3TimeClockRefPriority	1.3.6.1.4.1.2544.1.12.12.1.4.1.4	Integer32	read-create	This object represents the priority of the external reference to be used as Time clock reference source. This value is not mandatory when a single clock reference source is supported. Lower priority value indicates higher priority.
NUM f3TimeClockRefReference	1.3.6.1.4.1.2544.1.12.12.1.4.1.3	VariablePointer	read-create	This object represents the external reference to be used as system clock reference source.
ROW f3TimeClockRefRowStatus	1.3.6.1.4.1.2544.1.12.12.1.4.1.9	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3TimeClockRefRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3TimeClockRefRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3TimeClockRefRowStatus object may be modified if the associated instance of this object is equal to active(1).
SYN f3TimeClockRefState	1.3.6.1.4.1.2544.1.12.12.1.4.1.6	SyncRefState	read-only	This object provides the Time Clock reference state.
SYN f3TimeClockRefStatus	1.3.6.1.4.1.2544.1.12.12.1.4.1.5	SyncRefStatus	read-only	This object provides the Time Clock reference status.
STO f3TimeClockRefStorageType	1.3.6.1.4.1.2544.1.12.12.1.4.1.8	StorageType	read-create	The type of storage configured for this entry.
f3TimeClockRefTable	1.3.6.1.4.1.2544.1.12.12.1.4		not-accessible	A list of entries corresponding to the Time Clock Reference entities.
SEC f3TimeClockSecondaryState	1.3.6.1.4.1.2544.1.12.12.1.3.1.5	SecondaryState	read-only	This object represents the Secondary State of the Time Clock Entity.
NUM f3TimeClockSelectedReference	1.3.6.1.4.1.2544.1.12.12.1.3.1.6	VariablePointer	read-only	This object provides the source of the currently selected Time Clock reference. This would be the OID of the actual entity (GPS port, PPS port etc.). An OID value of {0 0} represents internal clock.
SYN f3TimeClockSelectionMode	1.3.6.1.4.1.2544.1.12.12.1.3.1.9	SyncSelectionMode	read-write	!! Currently Only Priority Mode is supported !! This object represents the Time Clock entity's selection mode. If this mode is configured as ql-mode, the selection of which reference should be used shall be based upon the reference's Quality Level. The highest received Quality Level shall be the selected reference. The priority shall only be used to distinguish between references with the same received QL. When multiple references have the same QL and same priority, the behavior of selection process within the group is non-revertive. If this mode is configued as priority-mode, the selection of which reference should be used shall be based upon the reference's priority (i.e. QL is disabled). When multiple references have the same priority, the behavior of selection process within the group is non-revertive.
T/F f3TimeClockSyncRefCandidate	1.3.6.1.4.1.2544.1.12.12.1.3.1.18	TruthValue	read-write	This object describe whether it is sync reference candiddate.
f3TimeClockTable	1.3.6.1.4.1.2544.1.12.12.1.3		not-accessible	A list of entries corresponding to the Time Clock entities.
TIM f3TimeClockTimeHoldoverPerformance	1.3.6.1.4.1.2544.1.12.12.1.3.1.19	TimeHoldoverPerformance	read-write	This object describe the Holdover performance.
I32 f3TimeClockTimeHoldoverTimeout	1.3.6.1.4.1.2544.1.12.12.1.3.1.27	Integer32	read-write	Configurable Holdover time The time (0..3000000 seconds) that the OCXO is expected to maintain the required accuracy and maintain Holdover-within-limits. Default is 0.
I32 f3TimeClockTimeInHoldoverEx	1.3.6.1.4.1.2544.1.12.12.1.3.1.28	Integer32	read-only	Time (seconds) in Holdover.
TIM f3TimeClockTimeScale	1.3.6.1.4.1.2544.1.12.12.1.3.1.24	TimeScale	read-write	This object allows configuration of the Sync entity's Time Scale. Only PTP or ARB values are allowed. In PTP mode, phase is recovered from time reference source. In ARB mode phase is taken from Linux time and locked on chosen reference.
TIM f3TimeClockTimeTraceAbilityStatus	1.3.6.1.4.1.2544.1.12.12.1.3.1.15	TimeTraceAbilityStatus	read-only	This object describe the trace ability status.
TOD f3TimeClockTODSource	1.3.6.1.4.1.2544.1.12.12.1.3.1.25	TODSource	read-only	This object provides the ARB TOD Source. The value decided according to the Time Scale parameter. Can be NA or System TOD.
U32 f3TimeClockUtcOffset	1.3.6.1.4.1.2544.1.12.12.1.3.1.20	Unsigned32	read-only	This object describe the UTC offset.
I32 f3TimeClockWaitToRestoreTime	1.3.6.1.4.1.2544.1.12.12.1.3.1.10	Integer32	read-write	This object allows configuration of the Time Clock entity's wait-to-restore time (in minutes). A value of 0 disables WTR timers for all references.

RFC description

Ciena F3 platform MIB for synchronization and timing management.

Start monitoring ADVA Optical Networking FSP150CM/CC (F3 platform) carrier Ethernet device (SyncE/timing synchronization) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download F3-SYNC-MIB