All MIBs › ERICSSON-ROUTER-IPPOOL-MIB
Organization: Ericsson AB
Last Updated: 2015-01-14
Category: Domain: Subscriber Management, Vendor: Ericsson
Description: Monitors and manages IP address pools used for subscriber address allocation on Ericsson routers.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ERICSSON-ROUTER-IPPOOL-MIB?
ERICSSON-ROUTER-IPPOOL-MIB manages and monitors IP address pools used for dynamic subscriber address allocation (e.g., PPP, DHCP) on Ericsson SmartEdge/SM/SSR routers. It exposes a pool table per interface/context giving pool address, mask, total size, and address-usage breakdown (available, unusable, in-use), along with configurable utilization thresholds and trap-enable flags. This is fundamentally a resource/configuration-status MIB used to monitor software-level capacity: operators watch eriRouterIpPoolAvailable versus eriRouterIpPoolSize to catch pool exhaustion before new subscriber sessions start failing, and eriRouterIpPoolSendTrap/threshold objects allow proactive trap-based alerting rather than constant polling. It's a standalone Ericsson MIB with no explicit dependency on external IETF address-pool standards, reflecting Ericsson's subscriber-management architecture. It's typically deployed in broadband/mobile edge routers (BNGs) where address pools serve large numbers of dynamically-provisioned subscriber sessions. Engineers can download the ERICSSON-ROUTER-IPPOOL-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ERICSSON-ROUTER-IPPOOL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Ericsson SmartEdge Multi-service Edge Router (MSER)
- Ericsson Smart Service Router (SSR)
- Ericsson broadband/mobile edge router (BNG)
- Ericsson SmartEdge router series
Monitoring Examples
An operator polls eriRouterIpPoolTable/eriRouterIpPoolEntry, keyed by eriRouterIpPoolInterfaceIdx, comparing eriRouterIpPoolInuse and eriRouterIpPoolAvailable against eriRouterIpPoolSize for a pool identified by eriRouterIpPoolAddr/eriRouterIpPoolMask. If eriRouterIpPoolAvailable falls below the configured eriRouterIpPoolThreshold, the router can raise a trap (per eriRouterIpPoolSendTrap) via eriRouterIpPoolMIBNotifications, alerting the NOC that the pool on eriRouterIpPoolInterfaceName is nearing exhaustion and new subscriber sessions may soon be rejected.
What Can Be Monitored
- IP pool size
- addresses in use
- addresses available
- unusable addresses
- utilization threshold
- pool exhaustion trap status
This MIB depends on
Related MIBs
Imported Objects
From ERICSSON-ROUTER-SMI
| eriRouterMgmt | OBJECT-IDENTITY |
From ERICSSON-ROUTER-TC
| EriRouterPercentage |
From IF-MIB
| InterfaceIndex |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressPrefixLength | |
| InetAddressType |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| eriRouterIpPoolMib | 1.3.6.1.4.1.193.218.2.15 | Defines the objects necessary to obtain information about IP Pools for interfaces within a context. | ||
| eriRouterIpPoolMIBNotifications | 1.3.6.1.4.1.193.218.2.15.0 | |||
| NTF eriRouterIpPoolThresholdMet | 1.3.6.1.4.1.193.218.2.15.0.1 | A notification indicating that the per pool falling threshold has been reached. | ||
| NTF eriRouterIpPoolContextThresholdMet | 1.3.6.1.4.1.193.218.2.15.0.2 | A notification indicating that the per-context falling threshold has been reached. | ||
| NTF eriRouterIpPoolContextThresholdPercentageMet | 1.3.6.1.4.1.193.218.2.15.0.3 | A notification indicating that the per-context percentage falling threshold has been reached. | ||
| NTF eriRouterInetIpPoolHiFallingThrshMet | 1.3.6.1.4.1.193.218.2.15.0.4 | A notification indicating that the falling threshold with the high water mark(eriRouterInetIpPoolHiFallingThrsh) per IP Pool has been reached. | ||
| NTF eriRouterInetIpPoolLoFallingThrshMet | 1.3.6.1.4.1.193.218.2.15.0.5 | A notification indicating that the falling threshold with the low water mark(eriRouterInetIpPoolLoFallingThrsh) per IP Pool has been reached. | ||
| NTF eriRouterInetIpPoolCtxHiFallingThrshMet | 1.3.6.1.4.1.193.218.2.15.0.6 | A notification indicating that the falling threshold with the high water mark(eriRouterInetIpPoolCtxHiFallingThrsh) per IP Pool has been reached. | ||
| NTF eriRouterInetIpPoolCtxLoFallingThrshMet | 1.3.6.1.4.1.193.218.2.15.0.7 | A notification indicating that the falling threshold with the low water mark(eriRouterInetIpPoolCtxLoFallingThrsh) per IP Pool has been reached. | ||
| eriRouterIpPoolMIBObjects | 1.3.6.1.4.1.193.218.2.15.1 | |||
| eriRouterIpPoolTable | 1.3.6.1.4.1.193.218.2.15.1.1 | not-accessible | The purpose of this table is to allow customers to monitor the status of IP Pools on their SMS systems through SNMP. This table contains the objects which identify information about IP Pools. Each row in the table corresponds to one IP Pool for a given interface within a particular context. Objects defined in this table are only accessible within the context identified in the SNMP protocol (i.e. the community string in v1/v2c or the contextName in v3). | |
| eriRouterIpPoolEntry | 1.3.6.1.4.1.193.218.2.15.1.1.1 | not-accessible | A conceptual row in the eriRouterIpPoolTable. | |
| U32 eriRouterIpPoolInterfaceIdx | 1.3.6.1.4.1.193.218.2.15.1.1.1.1 | Unsigned32 | not-accessible | The index of the interface containing the IP Pool. |
| IP eriRouterIpPoolAddr | 1.3.6.1.4.1.193.218.2.15.1.1.1.2 | IpAddress | not-accessible | The start address of the IP Pool. |
| STR eriRouterIpPoolInterfaceName | 1.3.6.1.4.1.193.218.2.15.1.1.1.3 | SnmpAdminString | read-only | The name of the interface containing the IP Pool. |
| IP eriRouterIpPoolMask | 1.3.6.1.4.1.193.218.2.15.1.1.1.4 | IpAddress | read-only | The subnet mask of the IP Pool. This object will be instantiated for IP Pools of type subnet only. |
| U32 eriRouterIpPoolSize | 1.3.6.1.4.1.193.218.2.15.1.1.1.5 | Unsigned32 | read-only | The size of the IP Pool is defined to be the sum of the available addresses plus the unusable addresses. |
| U32 eriRouterIpPoolAvailable | 1.3.6.1.4.1.193.218.2.15.1.1.1.6 | Unsigned32 | read-only | The number of addresses of an IP Pool that are available. |
| U32 eriRouterIpPoolUnusable | 1.3.6.1.4.1.193.218.2.15.1.1.1.7 | Unsigned32 | read-only | Unusable IP addresses in an IP Pool consist of the ip address of the interface, and those used by the network address and the broadcast address of the interface. |
| U32 eriRouterIpPoolInuse | 1.3.6.1.4.1.193.218.2.15.1.1.1.8 | Unsigned32 | read-only | The number of addresses of an IP Pool that are in use. |
| U32 eriRouterIpPoolThreshold | 1.3.6.1.4.1.193.218.2.15.1.1.1.9 | Unsigned32 | read-only | The threshold of an IP Pool is the value for currently available addresses, as reported in eriRouterIpPoolAvailable, which causes a trap and/or log message to be generated when this value is reached. This is a falling threshold, so a trap and/or log message will only be sent on a transition of the value of available addresss from (eriRouterIpPoolThreshold+1) addresses to eriRouterIpPoolThreshold addresses. Additionally, the action of sending the trap and/or log message is subject to the values of eriRouterIpPoolSendTrap and eriRouterIpPoolLogMessage. A value of zero means there is no threshold. |
| T/F eriRouterIpPoolSendTrap | 1.3.6.1.4.1.193.218.2.15.1.1.1.10 | TruthValue | read-only | If true, upon detection of reaching a per-pool threshold event, a trap will be sent. See the definition of the eriRouterIpPoolThresholdMet for the information included in the trap. Note, both eriRouterIpPoolSendTrap and eriRouterIpPoolLogMessage are allowed to be TRUE at the same time. |
| T/F eriRouterIpPoolLogMessage | 1.3.6.1.4.1.193.218.2.15.1.1.1.11 | TruthValue | read-only | If true, upon detection of reaching a per-pool threshold event, a message will be logged. The information contained in the message is the same as that included in the eriRouterIpPoolThresholdMet trap. Note, both eriRouterIpPoolSendTrap and eriRouterIpPoolLogMessage are allowed to be TRUE at the same time. |
| STR eriRouterIpPoolName | 1.3.6.1.4.1.193.218.2.15.1.1.1.12 | SnmpAdminString | read-only | The name of the IP Pool. |
| INT eriRouterIpPoolType | 1.3.6.1.4.1.193.218.2.15.1.1.1.13 | INTEGER | read-only | The type of the IP Pool. |
| IP eriRouterIpPoolEndAddr | 1.3.6.1.4.1.193.218.2.15.1.1.1.14 | IpAddress | read-only | The end address of the IP Pool. This object will be instantiated for range IP Pools only. |
| eriRouterIpPoolSummary | 1.3.6.1.4.1.193.218.2.15.1.2 | |||
| STR eriRouterIpPoolContextName | 1.3.6.1.4.1.193.218.2.15.1.2.1 | SnmpAdminString | read-only | The name of the context containing the IP Pool. |
| U32 eriRouterIpPoolContextAvailable | 1.3.6.1.4.1.193.218.2.15.1.2.2 | Unsigned32 | read-only | The total number of IP addresses available in all pools of all interfaces in the context valid in the current view. |
| U32 eriRouterIpPoolContextThreshold | 1.3.6.1.4.1.193.218.2.15.1.2.3 | Unsigned32 | read-only | The per-context threshold of an IP Pool is the value for currently available per-context addresses, as reported in eriRouterIpPoolContextAvailable, which causes a trap and/or log message to be generated when this value is reached. This is a falling threshold, so a trap and/or log message will only be sent on a transition of the value of available addresss from (eriRouterIpPoolContextThreshold+1) addresses to eriRouterIpPoolContextThreshold addresses. Additionally, the action of sending the trap and/or log message is subject to the values of eriRouterIpPoolContextSendTrap and eriRouterIpPoolContextLogMessage. A value of zero means there is no per-context threshold. |
| T/F eriRouterIpPoolContextSendTrap | 1.3.6.1.4.1.193.218.2.15.1.2.4 | TruthValue | read-only | If true, upon detection of a per-context threshold crossing event, a trap will be sent. See the definition of the eriRouterIpPoolContextThresholdMet for the information included in the trap. Note, both eriRouterIpPoolContextSendTrap and eriRouterIpPoolContextLogMessage are allowed to be true at the same time. |
| T/F eriRouterIpPoolContextLogMessage | 1.3.6.1.4.1.193.218.2.15.1.2.5 | TruthValue | read-only | If true, upon detection of a per-context threshold crossing event, a message will be logged. The information contained in the message logged is the same as that included in the eriRouterIpPoolContextThresholdMet trap. Note, both eriRouterIpPoolContextSendTrap and eriRouterIpPoolContextLogMessage are allowed to be true at the same time. |
| U32 eriRouterIpPoolContextTotalSize | 1.3.6.1.4.1.193.218.2.15.1.2.6 | Unsigned32 | read-only | The total number of IP addresses configured in all pools of all interfaces in the context valid in the current view. It is the sum of the available addresses plus the unusable addresses. |
| eriRouterIpPoolContextThresholdPercentTable | 1.3.6.1.4.1.193.218.2.15.1.2.7 | not-accessible | The purpose of this table is to allow customers to monitor the status of per-context IP Pool percentage thresholds through SNMP. This table contains the objects which identify information about per-context IP Pool thresholds expressed in percentage. Each row in the table corresponds to one IP Pool percentage threshold configured within a particular context. Objects defined in this table are only accessible within the context identified in the SNMP protocol (i.e. the community string in v1/v2c or the contextName in v3). | |
| eriRouterIpPoolContextThresholdPercentEntry | 1.3.6.1.4.1.193.218.2.15.1.2.7.1 | not-accessible | A conceptual row in the eriRouterIpPoolContextThresholdPercentTable. | |
| U32 eriRouterIpPoolContextThresholdIndex | 1.3.6.1.4.1.193.218.2.15.1.2.7.1.1 | Unsigned32 | not-accessible | The index of the IP Pool percentage threshold. |
| ERI eriRouterIpPoolContextThresholdPercentage | 1.3.6.1.4.1.193.218.2.15.1.2.7.1.2 | EriRouterPercentage | read-only | A threshold for the percentage of the number of currently available IP Pool addresses against the total number of IP Pool addresses configured within the context. This is a falling threshold, so an SNMP trap and/or log message will only be sent when the current value, which is the % of eriRouterIpPoolContextAvailable/eriRouterIpPoolContextTotalSize truncated to a whole number in percentage, is less than or equal to this threshold, and the percentage value at the last check was greater than this threshold. Additionally, the action of sending the SNMP trap and/or logging a message is subject to the values of eriRouterIpPoolContextThresholdSendTrap and eriRouterIpPoolContextThresholdLogMessage. |
| T/F eriRouterIpPoolContextThresholdSendTrap | 1.3.6.1.4.1.193.218.2.15.1.2.7.1.3 | TruthValue | read-only | If true, upon detection of a per-context threshold crossing event, an SNMP trap will be sent. See the definition of the eriRouterIpPoolContextThresholdPercentageMet for the information included in the trap. Note, both eriRouterIpPoolContextThresholdSendTrap and eriRouterIpPoolContextThresholdLogMessage are allowed to be true at the same time. |
| T/F eriRouterIpPoolContextThresholdLogMessage | 1.3.6.1.4.1.193.218.2.15.1.2.7.1.4 | TruthValue | read-only | If true, upon detection of a per-context threshold crossing event, a message will be logged. The information contained in the message logged is the same as that included in the eriRouterIpPoolContextThresholdPercentageMet trap. Note, both eriRouterIpPoolContextThresholdSendTrap and eriRouterIpPoolContextThresholdLogMessage are allowed to be true at the same time. |
| eriRouterInetIpPoolTable | 1.3.6.1.4.1.193.218.2.15.1.3 | not-accessible | This table contains the objects which identify information about IP Pools (such as ND IPv6 pool and DHCP-PD IPv6 Pool). Each row in the table corresponds to one IP Pool for either a given interface within a particular context or only within a particular context . If this pool is only configured per context basis, the interface index is set to zero. The IPv6 pool range is from start prefix/length to the end prefix/length. The prefix length for start and end prefixes are the same, and refer to the prefix length to be advertised or delegated. Objects defined in this table are only accessible within the context identified in the SNMP protocol (i.e. the community string in v1/v2c or the contextName in v3). | |
| eriRouterInetIpPoolEntry | 1.3.6.1.4.1.193.218.2.15.1.3.1 | not-accessible | A conceptual row in the eriRouterInetIpPoolTable. | |
| ERI eriRouterInetIpPoolType | 1.3.6.1.4.1.193.218.2.15.1.3.1.1 | EriRouterInetPoolType | not-accessible | The type of IP Pool. |
| NUM eriRouterInetIpPoolIfIndex | 1.3.6.1.4.1.193.218.2.15.1.3.1.2 | InterfaceIndex | not-accessible | The index of the interface containing the IP Pool. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex. |
| IPt eriRouterInetIpPoolStartPrefixType | 1.3.6.1.4.1.193.218.2.15.1.3.1.3 | InetAddressType | not-accessible | The address type of eriRouterInetIpPoolPrefix. |
| IP eriRouterInetIpPoolStartPrefix | 1.3.6.1.4.1.193.218.2.15.1.3.1.4 | InetAddress | not-accessible | The start address prefix of this pool. The address type of this object is specified in eriRouterInetIpPoolPrefixType. The length of this object is the standard length for objects of that type (always 16 bytes). Any bits after eriRouterInetIpPoolStartPrefixLen must be zero. |
| ADR eriRouterInetIpPoolStartPrefixLen | 1.3.6.1.4.1.193.218.2.15.1.3.1.5 | InetAddressPrefixLength | not-accessible | The prefix length associated with this prefix. It refers to advertised or delegated prefix length. |
| IPt eriRouterInetIpPoolEndPrefixType | 1.3.6.1.4.1.193.218.2.15.1.3.1.6 | InetAddressType | read-only | The address type of eriRouterInetIpPoolPrefix. The value of this object is always ipv6 (2). |
| IP eriRouterInetIpPoolEndPrefix | 1.3.6.1.4.1.193.218.2.15.1.3.1.7 | InetAddress | read-only | The end IP address prefix of this pool. The address type of this object is specified in eriRouterInetIpPoolPrefixType. Any bits after eriRouterInetIpPoolPrefixLen must be zero. |
| ADR eriRouterInetIpPoolEndPrefixLen | 1.3.6.1.4.1.193.218.2.15.1.3.1.8 | InetAddressPrefixLength | read-only | The IP prefix length associated with this prefix. It refers to the advertised or delegated prefix length. See eriRouterInetIpPoolEndPrefixLen. |
| STR eriRouterInetIpPoolInterfaceName | 1.3.6.1.4.1.193.218.2.15.1.3.1.9 | SnmpAdminString | read-only | The name of the interface containing the IP Pool. |
| STR eriRouterInetIpPoolName | 1.3.6.1.4.1.193.218.2.15.1.3.1.10 | SnmpAdminString | read-only | The name of the IP Pool. |
| U32 eriRouterInetIpPoolSize | 1.3.6.1.4.1.193.218.2.15.1.3.1.11 | Unsigned32 | read-only | The size of the IP Pool is defined to be the sum of the available prefixes plus the unusable prefixes. |
| U32 eriRouterInetIpPoolAvailable | 1.3.6.1.4.1.193.218.2.15.1.3.1.12 | Unsigned32 | read-only | The number of IP address prefixes of an IP Pool that are available. |
| U32 eriRouterInetIpPoolUnusable | 1.3.6.1.4.1.193.218.2.15.1.3.1.13 | Unsigned32 | read-only | Unusable IP prefixes in an IP Pool. |
| U32 eriRouterInetIpPoolInuse | 1.3.6.1.4.1.193.218.2.15.1.3.1.14 | Unsigned32 | read-only | The number of IP prefixes of an IP Pool that are in use. |
| ERI eriRouterInetIpPoolThrshType | 1.3.6.1.4.1.193.218.2.15.1.3.1.15 | EriRouterInetIpPoolThresholdType | read-only | This object indicates the value type of all threshold values in this logical row, including eriRouterInetIpPoolHiFallingThrsh, eriRouterInetIpPoolLoFallingThrsh. |
| ERI eriRouterInetIpPoolHiFallingThrsh | 1.3.6.1.4.1.193.218.2.15.1.3.1.16 | EriRouterInetIpPoolThreshold | read-only | The falling threshold of an IP Pool. When the value of eriRouterInetIpPoolAvailable crosses from (eriRouterInetIpPoolHiFallingThrsh + 1) to eriRouterInetIpPoolHiFallingThrsh in either absolute value or percentage specified by eriRouterInetIpPoolThrshType, a eriRouterInetIpPoolHiFallingThrshMet notification and/or log is generated. The value of this object should never be smaller than the value of eriRouterInetIpPoolLoFallingThrsh. A value of zero means that this falling threshold is not configured. |
| ERI eriRouterInetIpPoolHiFallingNotify | 1.3.6.1.4.1.193.218.2.15.1.3.1.17 | EriRouterInetIpPoolThrshNotify | read-only | This object specifies if eriRouterInetIpPoolHiFallingThrshMet and/or log is generated. See the description of eriRouterInetIpPoolHiFallingThrsh for conditions which generate the notification. |
| ERI eriRouterInetIpPoolLoFallingThrsh | 1.3.6.1.4.1.193.218.2.15.1.3.1.18 | EriRouterInetIpPoolThreshold | read-only | The falling threshold of an IP Pool. When the value of eriRouterInetIpPoolAvailable crosses from (eriRouterInetIpPoolLoFallingThrsh + 1) to eriRouterInetIpPoolLoFallingThrsh (either absolute value or percentage) specified by eriRouterInetIpPoolThrshType, a eriRouterInetIpPoolLoFallingThrshMet notification and/or log is generated. The value of this object should never be greater than the value of eriRouterInetIpPoolHiFallingThrsh. A value of zero means that this falling threshold is not configured. |
| ERI eriRouterInetIpPoolLoFallingNotify | 1.3.6.1.4.1.193.218.2.15.1.3.1.19 | EriRouterInetIpPoolThrshNotify | read-only | This object specifies if eriRouterInetIpPoolLoFallingThrshMet and/or log is generated. See the description of eriRouterInetIpPoolLoFallingThrsh for conditions which generate the notification. |
| eriRouterInetIpPoolSummary | 1.3.6.1.4.1.193.218.2.15.1.4 | |||
| STR eriRouterInetIpPoolCtxName | 1.3.6.1.4.1.193.218.2.15.1.4.1 | SnmpAdminString | accessible-for-notify | The name of the context containing the IP Pool. |
| eriRouterInetIpPoolCtxTable | 1.3.6.1.4.1.193.218.2.15.1.4.2 | not-accessible | The purpose of this table is to allow customers to monitor the status of IP Pool context summary and thresholds through SNMP. This table contains the objects which identify information about per-context IP Pool thresholds expressed in absolute value or percentage. Each row in the table corresponds to one IP Pool threshold configured within a particular context. Objects defined in this table are only accessible within the context identified in the SNMP protocol (i.e. the community string in v1/v2c or the contextName in v3). | |
| eriRouterInetIpPoolCtxEntry | 1.3.6.1.4.1.193.218.2.15.1.4.2.1 | not-accessible | A conceptual row in the eriRouterInetIpPoolCtxTable. | |
| ERI eriRouterInetIpPoolCtxPoolType | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.1 | EriRouterInetPoolType | not-accessible | The type of ip pool. |
| U32 eriRouterInetIpPoolCtxAvailable | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.2 | Unsigned32 | read-only | The number of IP address prefixes of an IP Pool that are available. |
| U32 eriRouterInetIpPoolCtxPoolSize | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.3 | Unsigned32 | read-only | The total number of IP prefixes configured in all pools of all interfaces in the context valid in the current view. It is the sum of the available plus the unusable prefixes. |
| ERI eriRouterInetIpPoolCtxThrshType | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.4 | EriRouterInetIpPoolThresholdType | read-only | This object indicates the value type of all threshold values in this logical row, including eriRouterInetIpPoolCtxHiFallingThrsh, eriRouterInetIpPoolCtxLoFallingThrsh. |
| ERI eriRouterInetIpPoolCtxHiFallingThrsh | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.5 | EriRouterInetIpPoolThreshold | read-only | The falling threshold of an IP Pool. When the value of eriRouterInetIpPoolCtxAvailable crosses from (eriRouterInetIpPoolCtxHiFallingThrsh + 1) to eriRouterInetIpPoolCtxHiFallingThrsh in either absolute value or percentage specified by eriRouterInetIpPoolCtxThrshType, a eriRouterInetIpPoolCtxHiFallingThrshMet notification and/or log is generated. The value of this object should never be smaller than the value of eriRouterInetIpPoolCtxLoFallingThrsh. A value of zero means that this falling threshold is not configured. |
| ERI eriRouterInetIpPoolCtxHiFallingNotify | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.6 | EriRouterInetIpPoolThrshNotify | read-only | This object specifies if eriRouterInetIpPoolCtxHiFallingThrshMet and/or log is generated. See the description of eriRouterInetIpPoolCtxHiFallingThrsh for conditions which generate the notification. |
| ERI eriRouterInetIpPoolCtxLoFallingThrsh | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.7 | EriRouterInetIpPoolThreshold | read-only | The falling threshold of an IP Pool. When the value of eriRouterInetIpPoolCtxAvailable crosses from (eriRouterInetIpPoolCtxLoFallingThrsh + 1) to eriRouterInetIpPoolCtxLoFallingThrsh (either absolute value or percentage) specified by eriRouterInetIpPoolCtxThrshType, a eriRouterInetIpPoolCtxLoFallingThrshMet notification and/or log is generated. The value of this object should never be greater than the value of eriRouterInetIpPoolCtxHiFallingThrsh. A value of zero means that this falling threshold is not configured. |
| ERI eriRouterInetIpPoolCtxLoFallingNotify | 1.3.6.1.4.1.193.218.2.15.1.4.2.1.8 | EriRouterInetIpPoolThrshNotify | read-only | This object specifies if eriRouterInetIpPoolCtxLoFallingThrshMet and/or log is generated. See the description of eriRouterInetIpPoolCtxLoFallingThrsh for conditions which generate the notification. |
| eriRouterIpPoolMIBConformance | 1.3.6.1.4.1.193.218.2.15.2 | |||
| eriRouterIpPoolCompliances | 1.3.6.1.4.1.193.218.2.15.2.1 | |||
| eriRouterIpPoolCompliance | 1.3.6.1.4.1.193.218.2.15.2.1.1 | The compliance statement for SNMP entities which implement this IP Pool MIB. | ||
| eriRouterIpPoolNameCompliance | 1.3.6.1.4.1.193.218.2.15.2.1.2 | The compliance statement for SNMP entities which implement this IP Pool MIB, including support for named pools. | ||
| eriRouterIpPoolComplianceV2 | 1.3.6.1.4.1.193.218.2.15.2.1.3 | The compliance statement for SNMP entities which implement this IP Pool MIB. | ||
| eriRouterIpPoolNameComplianceV2 | 1.3.6.1.4.1.193.218.2.15.2.1.4 | The compliance statement for SNMP entities which implement this IP Pool MIB, including support for named pools. | ||
| eriRouterIpPoolRangeCompliance | 1.3.6.1.4.1.193.218.2.15.2.1.5 | The compliance statement for SNMP entities which implement thhis IP Pool MIB, including support for range ip pools. | ||
| eriRouterIpPoolThresholdPercentCompliance | 1.3.6.1.4.1.193.218.2.15.2.1.6 | The compliance statement for SNMP entities which implement this IP Pool MIB, including support for per-context KIP Pool percentage thresholds. | ||
| eriRouterInetIpPoolCompliance | 1.3.6.1.4.1.193.218.2.15.2.1.7 | The compliance statement for SNMP entities which implement the IP Pool MIB, including support DHCP-PD & ND IPv6 Pool. | ||
| eriRouterIpPoolGroups | 1.3.6.1.4.1.193.218.2.15.2.2 | |||
| eriRouterIpPoolGroup | 1.3.6.1.4.1.193.218.2.15.2.2.1 | The collection of objects providing interface IP Pool information. | ||
| eriRouterIpPoolNotifyGroup | 1.3.6.1.4.1.193.218.2.15.2.2.2 | The collection of notifications related to IP Pools. | ||
| eriRouterIpPoolNameGroup | 1.3.6.1.4.1.193.218.2.15.2.2.3 | An object providing the IP pool name. | ||
| eriRouterIpPoolGroupV2 | 1.3.6.1.4.1.193.218.2.15.2.2.4 | The collection of objects providing interface IP Pool information. | ||
| eriRouterIpPoolRangeGroup | 1.3.6.1.4.1.193.218.2.15.2.2.5 | An object providing an IP pool range information. | ||
| eriRouterIpPoolInterfaceGroup | 1.3.6.1.4.1.193.218.2.15.2.2.6 | The collection of objects providing interface IP Pool information. | ||
| eriRouterIpPoolContextGroup | 1.3.6.1.4.1.193.218.2.15.2.2.7 | The collection of objects providing context IP Pool information. | ||
| eriRouterIpPoolNotifyGroupV2 | 1.3.6.1.4.1.193.218.2.15.2.2.8 | The collection of notifications related to IP Pools. | ||
| eriRouterInetIpPoolGroup | 1.3.6.1.4.1.193.218.2.15.2.2.9 | The collection of objects providing context IP Pool information. | ||
| eriRouterInetIpPoolNotifyGroup | 1.3.6.1.4.1.193.218.2.15.2.2.10 | The collection of notifications related to IP Pools. |
RFC description
Ericsson vendor-specific MIB for IP address pool management on Ericsson routers supporting dynamic address allocation.
Start monitoring Ericsson SmartEdge routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.