All MIBs › ELTEX-SMI-ACTUAL
Organization: Eltex Enterprise, Ltd.
Last Updated: 2012-05-29
Category: Textual Conventions and Registries
Description: Establishes Eltex Networks' Structure of Management Information (SMI), the root OID tree and base definitions that all other Eltex enterprise MIBs build on.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ELTEX-SMI-ACTUAL?
ELTEX-SMI-ACTUAL is Eltex Networks' Structure of Management Information module, providing the root enterprise OID tree used by all other Eltex MIB modules, while also defining top-level alarm/notification branches for several Eltex hardware line cards and modules (PON/Teknovus, FXS-72 voice ports, PP4 power modules, MXA32 access controllers). It therefore mixes structural OID assignment with fault-monitoring notification groups, covering categories like PON alarm conditions, voice port (FXS) alarm and cleared states, and power supply (PP4) alarm conditions. Its practical monitoring value is centered on hardware fault/status reporting: alarm traps such as fxs72AlarmTraps and fxs72OkTraps signal when an FXS port module enters or clears an alarm state, mxa32AlarmTraps/mxa32OkTraps do the same for MXA32 access controller cards, and pp4AlarmTraps flags power module faults. Other Eltex product MIB modules depend on the enterprise OID root defined here, and the notification objects likely correlate with entity/physical-index information from ENTITY-MIB on multi-card Eltex chassis. It is deployed on Eltex Networks access and PON equipment such as MXA/FXS voice gateways and PON OLT/ONU line cards, and loading the ELTEX-SMI-ACTUAL MIB file is a prerequisite for any NMS that intends to receive these FXS, MXA32, or PP4 alarm traps.
IPNetwork Monitor allows you to monitor SNMP objects defined in ELTEX-SMI-ACTUAL. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Eltex LTX-16C — current XGS-PON/ComboPON OLT, up to 4096 XGS-PON subscribers
Monitoring Examples
An administrator would subscribe to fxs72AlarmTraps to be notified when an FXS-72 voice port card raises an alarm (e.g. a port or trunk fault), and watch for the corresponding fxs72OkTraps notification once the condition clears. Similarly, mxa32AlarmTraps/mxa32OkTraps report fault and recovery events on Eltex MXA32 access controller modules, while pp4AlarmTraps flags a power supply module problem on PP4-equipped chassis. ponTeknovusAlarmTraps covers alarm conditions on the PON/Teknovus-based access line, useful for catching optical or ONU-side faults.
What Can Be Monitored
- FXS voice port alarm/clear status
- MXA32 access controller alarm/clear status
- PP4 power module alarm status
- PON/Teknovus line alarm conditions
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| DisplayString | |
| TimeStamp |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| elcAlarmTraps | 1.3.6.1.4.1.35265.3.22 | |||
| NTF elcConfigSavedAlarmTrap | 1.3.6.1.4.1.35265.3.22.8 | Configuration save error. | ||
| NTF elcConfigSavedOkTrap | 1.3.6.1.4.1.35265.3.23.8 | Configuration saved. Descr = Configuration saved to flash | ||
| NTF elcDuplicateMacAlarmTrap | 1.3.6.1.4.1.35265.3.22.14 | Duplicate mac detected. Param1 = VID, Descr = mac. | ||
| NTF elcEponAlarmTrap | 1.3.6.1.4.1.35265.3.22.7 | EPON port failed. Param 1 - link number | ||
| NTF elcEponOkTrap | 1.3.6.1.4.1.35265.3.23.7 | EPON port ok. Param 1 - link number | ||
| NTF elcFanAlarmTrap | 1.3.6.1.4.1.35265.3.22.4 | fan stopped. param1 = fan number | ||
| NTF elcFanOkTrap | 1.3.6.1.4.1.35265.3.23.4 | param1 = fan number | ||
| NTF elcFirmwareUpdateAlarmTrap | 1.3.6.1.4.1.35265.3.22.9 | Firmware update error. | ||
| NTF elcFirmwareUpdateOkTrap | 1.3.6.1.4.1.35265.3.23.9 | Firmware updated. Descr = Firmware updated | ||
| NTF elcFlappingAlarmTrap | 1.3.6.1.4.1.35265.3.22.6 | Period between OpticalAlarmTrap events is less than 30 seconds. Param 1 - link number | ||
| NTF elcFlappingOkTrap | 1.3.6.1.4.1.35265.3.23.6 | 1 minute passed after last OpticalAlarmTrap. Param 1 - link number | ||
| NTF elcLoadAverageAlarmTrap | 1.3.6.1.4.1.35265.3.22.15 | Load average exceeded limits. Param1 = 0 - 1 min, 1 - 5 min, 2 - 15 min | ||
| NTF elcLoadAverageOkTrap | 1.3.6.1.4.1.35265.3.23.15 | Load average is back to normal. Param1 = 0 - 1 min, 1 - 5 min, 2 - 15 min | ||
| NTF elcLoginAlarmTrap | 1.3.6.1.4.1.35265.3.22.12 | Login unsuccessful. Param1 = protocol (0 - serial, 1 - SSH, 2 - telnet, 3 - http, 4 - https) Descr = login, ip:port | ||
| NTF elcLoginOkTrap | 1.3.6.1.4.1.35265.3.23.12 | Login successful. Param1 = privileged/nonprivileged(1/0) Param1 = protocol (0 - serial, 1 - SSH, 2 - telnet, 3 - http, 4 - https) Descr = login, ip:port | ||
| NTF elcLogoutOkTrap | 1.3.6.1.4.1.35265.3.23.13 | User logged out. Param1 = privileged/nonprivileged(1/0) Param1 = protocol (0 - serial, 1 - SSH, 2 - telnet, 3 - http, 4 - https) Descr = login, ip:port | ||
| elcOkTraps | 1.3.6.1.4.1.35265.3.23 | |||
| NTF elcONTAuthAlarmTrap | 1.3.6.1.4.1.35265.3.22.1 | Bad registration ONT Event (mcTrapLParam1=Optical Interface Number, mcTrapDescr='description with MAC addr ONT') | ||
| NTF elcONTAuthOkTrap | 1.3.6.1.4.1.35265.3.23.1 | Normal registration ONT Event (mcTrapLParam1=Optical Interface Number, mcTrapDescr='description with MAC addr ONT') | ||
| NTF elcONTConfAlarmTrap | 1.3.6.1.4.1.35265.3.22.5 | ONT is not configured. Param1 = optical interface number, Descr = mac-address of ONT. | ||
| NTF elcONTConfOKTrap | 1.3.6.1.4.1.35265.3.23.5 | ONT is configured. Param1 = optical interface number, Descr = macaddress of ont | ||
| NTF elcOpticalAlarmTrap | 1.3.6.1.4.1.35265.3.22.3 | The optical link N (mcTrapLParam1) has no active devices | ||
| NTF elcOpticalOkTrap | 1.3.6.1.4.1.35265.3.23.3 | The optical link N (mcTrapLParam1) has M (mcTrapLParam2) active devices | ||
| NTF elcRAMAlarmTrap | 1.3.6.1.4.1.35265.3.22.11 | Ammount of free memory is < 5Mb | ||
| NTF elcRAMOkTrap | 1.3.6.1.4.1.35265.3.23.11 | Ammount of free memory is > 7Mb | ||
| NTF elcSwitchConfigChangeTrap | 1.3.6.1.4.1.35265.3.23.14 | Switch configuration has been changed | ||
| NTF elcTemperatureAlarmTrap | 1.3.6.1.4.1.35265.3.22.16 | Temperature is higher than 65 deg. Param1 = temperature value | ||
| NTF elcTemperatureOkTrap | 1.3.6.1.4.1.35265.3.23.16 | Temperature is lower than 60 deg. Param1 = temperature value | ||
| NTF elcUplinkAlarmTrap | 1.3.6.1.4.1.35265.3.22.2 | Uplink Down, mcTrapLParam1=Link Number, Description='GePON: Eth Link N down' | ||
| NTF elcUplinkOkTrap | 1.3.6.1.4.1.35265.3.23.2 | Eth Link Up, mcTrapLParam1=Link Number, Description='GePON: Eth Link N up' | ||
| NTF elcUserLoginAlarmTrap | 1.3.6.1.4.1.35265.3.22.10 | User login error **This entry is deprecated** | ||
| NTF elcUserLoginOkTrap | 1.3.6.1.4.1.35265.3.23.10 | User logged in from CLI. Param1 = privileged/nonprivileged (1/0), Descr = ${username} logged in ** This entry is deprecated. | ||
| elHardware | 1.3.6.1.4.1.35265.1 | The root of eltex hardware OIDs. | ||
| elSoftware | 1.3.6.1.4.1.35265.2 | The root of eltex software OIDs. | ||
| eltexLtd | 1.3.6.1.4.1.35265 | The Structure of Management Information for Eltex Networks. | ||
| NTF eltexShutdownTrap | 1.3.6.1.4.1.35265.3.99 | Agent is being normally shutdown. | ||
| eltrapDepNotificationGroup | 1.3.6.1.4.1.35265.3.103 | |||
| eltrapGroup | 1.3.6.1.4.1.35265.3 | The root of eltex traps objects. | ||
| eltrapNotificationGroup | 1.3.6.1.4.1.35265.3.100 | |||
| eltrapObjectGroup | 1.3.6.1.4.1.35265.3.101 | |||
| fxs72AlarmTraps | 1.3.6.1.4.1.35265.3.6 | |||
| NTF fxs72BpuAlarmTrap | 1.3.6.1.4.1.35265.3.6.12 | BPU is NOT available | ||
| NTF fxs72BpuOkTrap | 1.3.6.1.4.1.35265.3.7.12 | BPU is available | ||
| NTF fxs72FanAlarmTrap | 1.3.6.1.4.1.35265.3.6.4 | Fans are on, but not rotating. LParam1 = fan number | ||
| NTF fxs72FanLowSpeedAlarmTrap | 1.3.6.1.4.1.35265.3.6.22 | Fan rotation speed lower than 1000 rpm | ||
| NTF fxs72FanLowSpeedOkTrap | 1.3.6.1.4.1.35265.3.7.22 | Fan rotation speed is normal (more than 1000 rpm). | ||
| NTF fxs72FanOkTrap | 1.3.6.1.4.1.35265.3.7.4 | Fans are rotating. LParam1 = fan number | ||
| NTF fxs72FansSwitchTrap | 1.3.6.1.4.1.35265.3.7.11 | Fans has been switched on or off. LParam1 = 0 - off, 1 - on. | ||
| NTF fxs72LicenseAlarmTrap | 1.3.6.1.4.1.35265.3.6.14 | TAU-MEGACO 1.2 mcTrapExState: 1 - alarm, no license, 0 - ok license | ||
| NTF fxs72LicenseOkTrap | 1.3.6.1.4.1.35265.3.7.14 | TAU-MEGACO 1.2 mcTrapExState: 1 - alarm, no license, 0 - ok license | ||
| fxs72OkTraps | 1.3.6.1.4.1.35265.3.7 | |||
| NTF fxs72PortAlarmTrap | 1.3.6.1.4.1.35265.3.6.6 | Port Blocked. TAU-SIP Param1 = port number, p2=block cause, Descr = Block cause 0x00 - unknown cause (0x00) 0x01 - leakage current has exceeded the permissible parameters 0x02 - temperature has exceeded the permissible parameters 0x03 - power dissipation has exceeded the permissible parameters 0x04 - reinitialization by changing the input voltage 0x05 - hardware reset 0x06 - low Vbat level 0x07 - FXS port is out of order 0x08 - FXO line is not connected 0x09 - low FXO line current 0x0A - receiver offhook TAU-MEGACO p1=port, p2=cause 1-leakage_current 2-overheating 3-dissipated_power | ||
| NTF fxs72PortOkTrap | 1.3.6.1.4.1.35265.3.7.6 | Port unblocked. Param1 = port number, p2=state TAU-MEGACO p1=port, p2=state(ELTEX-FXS72::PortMegacoState) | ||
| NTF fxs72PowerUnitTermAlarm | 1.3.6.1.4.1.35265.3.6.21 | Power supply unit temperature is out of limit (more than 95 C) | ||
| NTF fxs72PowerUnitTermOk | 1.3.6.1.4.1.35265.3.7.21 | Power supply unit temperature is normal (lower than 95 C) | ||
| NTF fxs72SSwAlarmTrap | 1.3.6.1.4.1.35265.3.6.5 | Softswitch became disconnected TAU-MEGACO p1=status (undefined=0, connect=1, disconnect=2) | ||
| NTF fxs72SSwOkTrap | 1.3.6.1.4.1.35265.3.7.5 | Softswitch status ok. TAU-MEGACO p1=status (undefined=0, connect=1, disconnect=2) | ||
| NTF fxs72TemperatureAlarmTrap | 1.3.6.1.4.1.35265.3.6.3 | Temperature is too high. (Temp>90 deg). LParam1 = temperature value. LParam2 = sensor number | ||
| NTF fxs72TemperatureOkTrap | 1.3.6.1.4.1.35265.3.7.3 | Temperature is back to normal. LParam2 = sensor number | ||
| NTF fxs72TempmeasurementAlarmTrap | 1.3.6.1.4.1.35265.3.6.13 | Temperature measurement failed. TAU-SIP 2.9 | ||
| NTF fxs72TempmeasurementOkTrap | 1.3.6.1.4.1.35265.3.7.13 | Temperature measurement is OK. TAU-SIP 2.9 | ||
| NTF fxs72updateFwFail | 1.3.6.1.4.1.35265.3.6.20 | par1 = error type. descr = file + addr + FAIL | ||
| NTF fxs72updateFwOk | 1.3.6.1.4.1.35265.3.7.20 | descr = file + addr + OK | ||
| NTF fxs72VbatAlarmTrap | 1.3.6.1.4.1.35265.3.6.1 | Vbat is out of limits (Vbat72V). LParam1 = Vbat voltage | ||
| NTF fxs72VbatOkTrap | 1.3.6.1.4.1.35265.3.7.1 | Vbat is back to normal. | ||
| NTF fxs72VmodeSwitchTrap | 1.3.6.1.4.1.35265.3.7.10 | Voltage mode has been switched. LParam1 = new mode (1- 60V, 2 - 48V). | ||
| NTF fxs72VringAlarmTrap | 1.3.6.1.4.1.35265.3.6.2 | Vring1 or Vring2 is out of limits (Vring120V). LParam1 = Vring voltage. LParam2 = 1 or 2 | ||
| NTF fxs72VringOkTrap | 1.3.6.1.4.1.35265.3.7.2 | Vring1 or Vring2 is back to normal. LParam2 = 1 or 2 | ||
| mc240TrapTypes | 1.3.6.1.4.1.35265.3.5 | |||
| mccpAlarmTraps | 1.3.6.1.4.1.35265.3.30 | |||
| NTF mccpConfigAlarmTrap | 1.3.6.1.4.1.35265.3.30.1 | config file alarm | ||
| NTF mccpConfigOkTrap | 1.3.6.1.4.1.35265.3.31.1 | config file is normal | ||
| NTF mccpIntfAlarmTrap | 1.3.6.1.4.1.35265.3.30.7 | V52-Interface number [param1] Alarm | ||
| NTF mccpIntfOkTrap | 1.3.6.1.4.1.35265.3.31.7 | V52-Interface number [param1] is Normal | ||
| NTF mccpIntfSlotAlarmTrap | 1.3.6.1.4.1.35265.3.30.8 | 24AK slot [param2] on V52-Interface number [param1] Alarm | ||
| NTF mccpIntfSlotOkTrap | 1.3.6.1.4.1.35265.3.31.8 | 24AK slot [param2] on V52-Interface number [param1] is Normal | ||
| NTF mccpLinksetAlarmTrap | 1.3.6.1.4.1.35265.3.30.3 | SS7 Linkset alarm [param1] | ||
| NTF mccpLinksetOkTrap | 1.3.6.1.4.1.35265.3.31.3 | SS7 Linkset in work [param1] | ||
| mccpOkTraps | 1.3.6.1.4.1.35265.3.31 | |||
| NTF mccpSlotAlarmTrap | 1.3.6.1.4.1.35265.3.30.2 | slot [param1] alarm | ||
| NTF mccpSlotOkTrap | 1.3.6.1.4.1.35265.3.31.2 | slot [param1] in work | ||
| NTF mccpSS7LinkAlarmTrap | 1.3.6.1.4.1.35265.3.30.5 | SS7 Link alarm at [param1:param2] | ||
| NTF mccpSS7LinkOkTrap | 1.3.6.1.4.1.35265.3.31.5 | SS7 Link at [param1:param2] in work | ||
| NTF mccpStartOkTrap | 1.3.6.1.4.1.35265.3.31.16 | MCCP started | ||
| NTF mccpStreamAlarmTrap | 1.3.6.1.4.1.35265.3.30.4 | Stream alarm at [param1:param2] state=%s [state] | ||
| NTF mccpStreamOkTrap | 1.3.6.1.4.1.35265.3.31.4 | Stream alarm at [param1:param2] in work | ||
| NTF mccpSutdownSnmpdAlarmTrap | 1.3.6.1.4.1.35265.3.30.17 | shutdown snmpd | ||
| NTF mccpSyncAlarmTrap | 1.3.6.1.4.1.35265.3.30.6 | Low priority sync state or no sync | ||
| NTF mccpSyncOkTrap | 1.3.6.1.4.1.35265.3.31.6 | Normal sync state | ||
| I32 mcReservedFlag | 1.3.6.1.4.1.35265.3.5.9 | Integer32 | read-only | Reserved flag |
| STR mcTrapDescr | 1.3.6.1.4.1.35265.3.5.6 | DisplayString | read-only | Alarm description |
| I32 mcTrapExState | 1.3.6.1.4.1.35265.3.5.1 | Integer32 | read-only | state (additional state) |
| I32 mcTrapID | 1.3.6.1.4.1.35265.3.5.5 | Integer32 | read-only | ID (pbx trap id) |
| I32 mcTrapLParam1 | 1.3.6.1.4.1.35265.3.5.2 | Integer32 | read-only | param-1 (slot or index) |
| I32 mcTrapLParam2 | 1.3.6.1.4.1.35265.3.5.3 | Integer32 | read-only | param-2 (port or index) |
| I32 mcTrapLParam3 | 1.3.6.1.4.1.35265.3.5.4 | Integer32 | read-only | param-3 (other index) |
| I32 mcTrapRestoredAlarmID | 1.3.6.1.4.1.35265.3.5.7 | Integer32 | read-only | If this restore event then here writed Alarm ID. If this alarm event then mcTrapRestoredAlarmID=0. |
| I32 mcTrapSyncType | 1.3.6.1.4.1.35265.3.5.8 | Integer32 | read-only | Type of trap: 0 - Normal; 1 - Journal alarms; 2 - Active alarms |
| mxa24AlarmTraps | 1.3.6.1.4.1.35265.3.18 | |||
| NTF mxa24DslLinkAlarmTrap | 1.3.6.1.4.1.35265.3.18.1 | Adsl port in down state. LParam1 - port number | ||
| NTF mxa24DslLinkOkTrap | 1.3.6.1.4.1.35265.3.19.1 | Adsl port is up. LParam1 - port number | ||
| NTF mxa24EthLinkAlarmTrap | 1.3.6.1.4.1.35265.3.18.2 | Uplink port in down state. LParam1 - port number | ||
| NTF mxa24EthLinkOkTrap | 1.3.6.1.4.1.35265.3.19.2 | Uplink port is up. LParam1 - port number | ||
| mxa24OkTraps | 1.3.6.1.4.1.35265.3.19 | |||
| NTF mxa24TempAlarmTrap | 1.3.6.1.4.1.35265.3.18.3 | Temperature is too high. LParam1 - sensor index: 0(sensor0), 1(sensor1) LParam3 - actual temperature value ['C] | ||
| NTF mxa24TempOkTrap | 1.3.6.1.4.1.35265.3.19.3 | Temperature normalization. LParam1 - sensor index: 0(sensor0), 1(sensor1) LParam3 - actual temperature value ['C] | ||
| NTF mxa24UserLoginTrap | 1.3.6.1.4.1.35265.3.18.5 | Device voltage is out of range. LParam1 - the process pid LParam2 - interface number: 1(console), 2(telnet), 3..6(web) | ||
| NTF mxa24UserLogoutTrap | 1.3.6.1.4.1.35265.3.19.5 | User logout. LParam1 - the process pid LParam2 - interface number: 1(console), 2(telnet), 3..6(web) | ||
| NTF mxa24VoltAlarmTrap | 1.3.6.1.4.1.35265.3.18.4 | Device voltage is out of range. LParam1 - voltage index: 2(1V), 3(12V), 4(-12V), 5(3.3V), 6(2.5V), 7(1.8V), 8(0.9V), 9(1.5V) LParam3 - actual voltage value [mV/10] | ||
| NTF mxa24VoltOkTrap | 1.3.6.1.4.1.35265.3.19.4 | Device voltage is in acceptable range. LParam1 - voltage index: 2(1V), 3(12V), 4(-12V), 5(3.3V), 6(2.5V), 7(1.8V), 8(0.9V), 9(1.5V) LParam3 - actual voltage value [mV/10] | ||
| mxa32AlarmTraps | 1.3.6.1.4.1.35265.3.14 | |||
| NTF mxa32DslLinkAlarmTrap | 1.3.6.1.4.1.35265.3.14.1 | Adsl port in down state. LParam1 - port number | ||
| NTF mxa32DslLinkOkTrap | 1.3.6.1.4.1.35265.3.15.1 | Adsl port is up. LParam1 - port number | ||
| NTF mxa32EthLinkAlarmTrap | 1.3.6.1.4.1.35265.3.14.2 | Uplink port in down state. LParam1 - port number | ||
| NTF mxa32EthLinkOkTrap | 1.3.6.1.4.1.35265.3.15.2 | Uplink port is up. LParam1 - port number | ||
| mxa32OkTraps | 1.3.6.1.4.1.35265.3.15 | |||
| NTF mxa32TempAlarmTrap | 1.3.6.1.4.1.35265.3.14.3 | Temperature is too high. LParam1 - sensor index: 0(sensor0), 1(sensor1) LParam3 - actual temperature value ['C] | ||
| NTF mxa32TempOkTrap | 1.3.6.1.4.1.35265.3.15.3 | Temperature normalization. LParam1 - sensor index: 0(sensor0), 1(sensor1) LParam3 - actual temperature value ['C] | ||
| NTF mxa32UserLoginTrap | 1.3.6.1.4.1.35265.3.14.5 | User logIN. LParam1 - the process pid LParam2 - interface number: 1(console), 2(telnet), 3..6(web) | ||
| NTF mxa32UserLogoutTrap | 1.3.6.1.4.1.35265.3.15.5 | User logOUT. LParam1 - the process pid LParam2 - interface number: 1(console), 2(telnet), 3..6(web) | ||
| NTF mxa32VoltAlarmTrap | 1.3.6.1.4.1.35265.3.14.4 | Device voltage is out of range. LParam1 - voltage index: 2(1V), 3(12V), 4(-12V), 5(3.3V), 6(2.5V), 7(1.8V), 8(0.9V), 9(1.5V) LParam3 - actual voltage value [mV/10] | ||
| NTF mxa32VoltOkTrap | 1.3.6.1.4.1.35265.3.15.4 | Device voltage is in acceptable range. LParam1 - voltage index: 2(1V), 3(12V), 4(-12V), 5(3.3V), 6(2.5V), 7(1.8V), 8(0.9V), 9(1.5V) LParam3 - actual voltage value [mV/10] | ||
| mxa64AlarmTraps | 1.3.6.1.4.1.35265.3.16 | |||
| NTF mxa64DslLinkAlarmTrap | 1.3.6.1.4.1.35265.3.16.1 | Adsl port in down state. LParam1 - port number | ||
| NTF mxa64DslLinkOkTrap | 1.3.6.1.4.1.35265.3.17.1 | Adsl port is up. LParam1 - port number | ||
| NTF mxa64EthLinkAlarmTrap | 1.3.6.1.4.1.35265.3.16.2 | Uplink port in down state. LParam1 - port number | ||
| NTF mxa64EthLinkOkTrap | 1.3.6.1.4.1.35265.3.17.2 | Uplink port is up. LParam1 - port number | ||
| mxa64OkTraps | 1.3.6.1.4.1.35265.3.17 | |||
| NTF mxa64TempAlarmTrap | 1.3.6.1.4.1.35265.3.16.3 | Temperature is too high. LParam1 - sensor index: 0(sensor0), 1(sensor1), 2(sensor2), 3(sensor3) LParam3 - actual temperature value ['C] | ||
| NTF mxa64TempOkTrap | 1.3.6.1.4.1.35265.3.17.3 | Temperature normalization. LParam1 - sensor index: 0(sensor0), 1(sensor1), 2(sensor2), 3(sensor3) LParam3 - actual temperature value ['C] | ||
| NTF mxa64UserLoginTrap | 1.3.6.1.4.1.35265.3.16.5 | User login. LParam1 - the process pid LParam2 - interface number: 1(console), 2(telnet), 3..6(web) | ||
| NTF mxa64UserLogoutTrap | 1.3.6.1.4.1.35265.3.17.5 | User logout. LParam1 - the process pid LParam2 - interface number: 1(console), 2(telnet), 3..6(web) | ||
| NTF mxa64VoltAlarmTrap | 1.3.6.1.4.1.35265.3.16.4 | Device voltage is out of range. LParam1 - voltage index: 4(1V), 5(12V), 6(-12V), 7(3.3V), 8(2.5V), 9(1.8V), 10(0.9V), 11(1.5V) LParam3 - actual voltage value [mV/10] | ||
| NTF mxa64VoltOkTrap | 1.3.6.1.4.1.35265.3.17.4 | Device voltage is in acceptable range. LParam1 - voltage index: 4(1V), 5(12V), 6(-12V), 7(3.3V), 8(2.5V), 9(1.8V), 10(0.9V), 11(1.5V) LParam3 - actual voltage value [mV/10] | ||
| omsOperationAlarmTraps | 1.3.6.1.4.1.35265.3.20 | |||
| NTF omsOperationCommandAlarm | 1.3.6.1.4.1.35265.3.20.1 | mcTrapLParam1 = command ; mcTrapLParam2 = filetype mcTrapDescr = Description of operarion: DeviceName, command , tftp host, config filename, status=Error, cause of error for 'sigtran' par3 = cause integer code, in description text - system(...) ret code if needed | ||
| NTF omsOperationCommandOk | 1.3.6.1.4.1.35265.3.21.1 | mcTrapLParam1 = command ; mcTrapLParam2 = filetype mcTrapDescr = Description of operarion: DeviceName, command , tftp host, config filename, status=Ok | ||
| omsOperationOkTraps | 1.3.6.1.4.1.35265.3.21 | |||
| ponTeknovusAlarmTraps | 1.3.6.1.4.1.35265.3.10 | |||
| NTF ponTeknovusBoardRebootTrap | 1.3.6.1.4.1.35265.3.11.20 | Board is being rebooted. Descr = initiated reboot | ||
| NTF ponTeknovusConfigMigrateAlarmTrap | 1.3.6.1.4.1.35265.3.10.18 | Config migrate error. Param1 = config type (0 - all, 1 - pon) | ||
| NTF ponTeknovusConfigMigrateOkTrap | 1.3.6.1.4.1.35265.3.11.18 | Config migrate success. Param1 = config type (0 - all, 1 - pon) | ||
| NTF ponTeknovusConfigRereadTrap | 1.3.6.1.4.1.35265.3.11.24 | Config was reread from flash. | ||
| NTF ponTeknovusConfigSavedAlarmTrap | 1.3.6.1.4.1.35265.3.10.8 | Configuration save error. | ||
| NTF ponTeknovusConfigSavedOkTrap | 1.3.6.1.4.1.35265.3.11.8 | Configuration saved. Descr = Configuration saved to flash | ||
| NTF ponTeknovusDuplicateMacAlarmTrap | 1.3.6.1.4.1.35265.3.10.14 | Duplicate mac detected. Param1 = VID, Descr = mac. | ||
| NTF ponTeknovusEponAlarmTrap | 1.3.6.1.4.1.35265.3.10.7 | EPON port failed. Param 1 - link number | ||
| NTF ponTeknovusEponOkTrap | 1.3.6.1.4.1.35265.3.11.7 | EPON port ok. Param 1 - link number | ||
| NTF ponTeknovusFanAlarmTrap | 1.3.6.1.4.1.35265.3.10.4 | fan stopped. param1 = fan number | ||
| NTF ponTeknovusFanOkTrap | 1.3.6.1.4.1.35265.3.11.4 | param1 = fan number | ||
| NTF ponTeknovusFirmwareUpdateAlarmTrap | 1.3.6.1.4.1.35265.3.10.9 | Firmware update error. | ||
| NTF ponTeknovusFirmwareUpdateOkTrap | 1.3.6.1.4.1.35265.3.11.9 | Firmware updated. Descr = Firmware updated | ||
| NTF ponTeknovusFlappingAlarmTrap | 1.3.6.1.4.1.35265.3.10.6 | Period between OpticalAlarmTrap events is less than 30 seconds. Param 1 - link number | ||
| NTF ponTeknovusFlappingOkTrap | 1.3.6.1.4.1.35265.3.11.6 | 1 minute passed after last OpticalAlarmTrap. Param 1 - link number | ||
| NTF ponTeknovusLoadAverageAlarmTrap | 1.3.6.1.4.1.35265.3.10.15 | Load average exceeded limits. Param1 = 0 - 1 min, 1 - 5 min, 2 - 15 min | ||
| NTF ponTeknovusLoadAverageOkTrap | 1.3.6.1.4.1.35265.3.11.15 | Load average is back to normal. Param1 = 0 - 1 min, 1 - 5 min, 2 - 15 min | ||
| NTF ponTeknovusLoginAlarmTrap | 1.3.6.1.4.1.35265.3.10.12 | Login unsuccessful. Param1 = protocol (0 - serial, 1 - SSH, 2 - telnet, 3 - http, 4 - https) Descr = login, ip:port | ||
| NTF ponTeknovusLoginOkTrap | 1.3.6.1.4.1.35265.3.11.12 | Login successful. Param1 = privileged/nonprivileged(1/0) Param1 = protocol (0 - serial, 1 - SSH, 2 - telnet, 3 - http, 4 - https) Descr = login, ip:port | ||
| NTF ponTeknovusLogoutOkTrap | 1.3.6.1.4.1.35265.3.11.13 | User logged out. Param1 = privileged/nonprivileged(1/0) Param1 = protocol (0 - serial, 1 - SSH, 2 - telnet, 3 - http, 4 - https) Descr = login, ip:port | ||
| ponTeknovusOkTraps | 1.3.6.1.4.1.35265.3.11 | |||
| NTF ponTeknovusONTAuthAlarmTrap | 1.3.6.1.4.1.35265.3.10.1 | Bad registration ONT Event (mcTrapLParam1=Optical Interface Number, mcTrapDescr='description with MAC addr ONT') | ||
| NTF ponTeknovusONTAuthOkTrap | 1.3.6.1.4.1.35265.3.11.1 | Normal registration ONT Event (mcTrapLParam1=Optical Interface Number, mcTrapDescr='description with MAC addr ONT') | ||
| NTF ponTeknovusONTConfAlarmTrap | 1.3.6.1.4.1.35265.3.10.5 | ONT is not configured. Param1 = optical interface number, Descr = mac-address of ONT. | ||
| NTF ponTeknovusONTConfigChangedTrap | 1.3.6.1.4.1.35265.3.11.23 | ONT config changed. Param1 = pon channel, Param2 = ID ONT, Descr = ADD|DEL|EDIT ELTXhhhhhhhh pon_channel id description | ||
| NTF ponTeknovusONTConfOKTrap | 1.3.6.1.4.1.35265.3.11.5 | ONT is configured. Param1 = optical interface number, Descr = macaddress of ont | ||
| NTF ponTeknovusONTDeconfigureTrap | 1.3.6.1.4.1.35265.3.11.21 | ONT is being deconfigured (before disconnect). Param1 = pon-channel, Description = mac-address | ||
| NTF ponTeknovusONTPortBlockedAlarmTrap | 1.3.6.1.4.1.35265.3.10.17 | ONT's UNI port blocked. Param1 = port number, Descr = mac-address of ONT | ||
| NTF ponTeknovusONTPortBlockedOkTrap | 1.3.6.1.4.1.35265.3.11.17 | ONT's UNI port not blocked. Param1 = port number, Descr = mac-address of ONT | ||
| NTF ponTeknovusONTStateChangedTrap | 1.3.6.1.4.1.35265.3.11.22 | ONT's state changed. Param1 = pon channel, Param2 = ID ONT, Descr = ELTXhhhhhhhh pon_channel id state | ||
| NTF ponTeknovusOpticalAlarmTrap | 1.3.6.1.4.1.35265.3.10.3 | The optical link N (mcTrapLParam1) has no active devices | ||
| NTF ponTeknovusOpticalOkTrap | 1.3.6.1.4.1.35265.3.11.3 | The optical link N (mcTrapLParam1) has M (mcTrapLParam2) active devices | ||
| NTF ponTeknovusRAMAlarmTrap | 1.3.6.1.4.1.35265.3.10.11 | Ammount of free memory is < 5Mb | ||
| NTF ponTeknovusRAMOkTrap | 1.3.6.1.4.1.35265.3.11.11 | Ammount of free memory is > 7Mb | ||
| NTF ponTeknovusSwitchConfigChangeTrap | 1.3.6.1.4.1.35265.3.11.14 | Switch configuration has been changed | ||
| NTF ponTeknovusTemperatureAlarmTrap | 1.3.6.1.4.1.35265.3.10.16 | Temperature is higher than 65 deg. Param1 = temperature value | ||
| NTF ponTeknovusTemperatureOkTrap | 1.3.6.1.4.1.35265.3.11.16 | Temperature is lower than 60 deg. Param1 = temperature value | ||
| NTF ponTeknovusUplinkAlarmTrap | 1.3.6.1.4.1.35265.3.10.2 | Uplink Down, mcTrapLParam1=Link Number, Description='GePON: Eth Link N down' | ||
| NTF ponTeknovusUplinkOkTrap | 1.3.6.1.4.1.35265.3.11.2 | Eth Link Up, mcTrapLParam1=Link Number, Description='GePON: Eth Link N up' | ||
| NTF ponTeknovusUserLoginAlarmTrap | 1.3.6.1.4.1.35265.3.10.10 | User login error **This entry is deprecated** | ||
| NTF ponTeknovusUserLoginOkTrap | 1.3.6.1.4.1.35265.3.11.10 | User logged in from CLI. Param1 = privileged/nonprivileged (1/0), Descr = ${username} logged in ** This entry is deprecated. | ||
| pp4AlarmTraps | 1.3.6.1.4.1.35265.3.12 | |||
| NTF pp4AutoNegotiationAlarmTrap | 1.3.6.1.4.1.35265.3.12.2 | Autonegotiation failed (Param1 = link number) | ||
| NTF pp4AutoNegotiationOkTrap | 1.3.6.1.4.1.35265.3.13.2 | Autonegotiation successful (Param1 = link number) | ||
| NTF pp4BoardAddOkTrap | 1.3.6.1.4.1.35265.3.13.13 | New board added to slot #par1. board type #par2 | ||
| NTF pp4BoardRemoveAlarmTrap | 1.3.6.1.4.1.35265.3.12.13 | Board removed from slot #par1. board type #par2 | ||
| NTF pp4CommitOkTrap | 1.3.6.1.4.1.35265.3.13.7 | Commit OK | ||
| NTF pp4ConfigChangedOkTrap | 1.3.6.1.4.1.35265.3.13.12 | Config pp4x Changed | ||
| NTF pp4ConfigRestoredOkTrap | 1.3.6.1.4.1.35265.3.13.18 | timeout for confirm. Config Restored Now | ||
| NTF pp4DuplicationMacAlarmTrap | 1.3.6.1.4.1.35265.3.12.10 | Duplication of MAC address on PP4 | ||
| NTF pp4FwConfirmNeededAlarmTrap | 1.3.6.1.4.1.35265.3.12.23 | |||
| NTF pp4FwUpdateAlarmTrap | 1.3.6.1.4.1.35265.3.12.22 | |||
| NTF pp4FwUpdateOkTrap | 1.3.6.1.4.1.35265.3.13.22 | |||
| NTF pp4LinkAlarmTrap | 1.3.6.1.4.1.35265.3.12.1 | Link is down (Param1 = link number) | ||
| NTF pp4LinkFlapAlarmTrap | 1.3.6.1.4.1.35265.3.12.11 | linkflap on ifindex=param1 | ||
| NTF pp4LinkFlapEndOkTrap | 1.3.6.1.4.1.35265.3.13.11 | linkflap End on ifindex=param1 | ||
| NTF pp4LinkOkTrap | 1.3.6.1.4.1.35265.3.13.1 | Link is up (Param1 = link number) | ||
| NTF pp4LoadAvgAlarmTrap | 1.3.6.1.4.1.35265.3.12.4 | Load avg > 95% (Param1 = 1-1min, 2-5 min, 3-15 min, all LAs in description | ||
| NTF pp4LoadAvgOkTrap | 1.3.6.1.4.1.35265.3.13.4 | Load avg is back to normal (Param1 = 1-1min, 2-5 min, 3-15 min, all LAs in description | ||
| NTF pp4LoadCpuAlarmTrap | 1.3.6.1.4.1.35265.3.12.9 | Load CPU Alarm | ||
| NTF pp4LoginAlarmTrap | 1.3.6.1.4.1.35265.3.12.5 | Login failed | ||
| NTF pp4LoginOkTrap | 1.3.6.1.4.1.35265.3.13.5 | Login OK | ||
| NTF pp4LogoutAlarmTrap | 1.3.6.1.4.1.35265.3.12.6 | Logout failed | ||
| NTF pp4LogoutOkTrap | 1.3.6.1.4.1.35265.3.13.6 | Logout OK | ||
| NTF pp4MemoryAlarmTrap | 1.3.6.1.4.1.35265.3.12.3 | Running out of free memory (Param1 = current ammount of free memory) | ||
| NTF pp4MemoryOkTrap | 1.3.6.1.4.1.35265.3.13.3 | Ammount of free memory is back to normal | ||
| pp4OkTraps | 1.3.6.1.4.1.35265.3.13 | |||
| NTF pp4PortCounterErrorFoundAlarmTrap | 1.3.6.1.4.1.35265.3.12.16 | Founded errors for this port-counter | ||
| NTF pp4PortCounterErrorFreeOkTrap | 1.3.6.1.4.1.35265.3.13.16 | No errors for this port-counter | ||
| NTF pp4RebootFwTimerAlarmTrap | 1.3.6.1.4.1.35265.3.12.21 | |||
| NTF pp4RebootStackAlarmTrap | 1.3.6.1.4.1.35265.3.12.20 | |||
| NTF pp4RebootUnitAlarmTrap | 1.3.6.1.4.1.35265.3.12.19 | |||
| NTF pp4RebootUnitOkTrap | 1.3.6.1.4.1.35265.3.13.19 | |||
| NTF pp4RoleChangedOkTrap | 1.3.6.1.4.1.35265.3.13.15 | Now unit number par[1] with position par[2] is Master | ||
| NTF pp4SaveAlarmTrap | 1.3.6.1.4.1.35265.3.12.8 | Save FAIL | ||
| NTF pp4SaveOkTrap | 1.3.6.1.4.1.35265.3.13.8 | Save OK | ||
| NTF pp4SyncDisallowedAlarmTrap | 1.3.6.1.4.1.35265.3.12.17 | User didn't set command to allow unit-synchronization | ||
| NTF pp4SyncDisallowedOkTrap | 1.3.6.1.4.1.35265.3.13.17 | User set command to allow unit-synchronization | ||
| NTF pp4UnitAddOkTrap | 1.3.6.1.4.1.35265.3.13.14 | UNIT number par[1] vas added to position left(par[2]=1) or right(par[2]=0) | ||
| NTF pp4UnitRemoveAlarmTrap | 1.3.6.1.4.1.35265.3.12.14 | UNIT number par[1] vas removed from position left(par[2]=1) or right(par[2]=0) | ||
| STR radiusDescr | 1.3.6.1.4.1.35265.3.5.15 | DisplayString | read-only | Notification description |
| radiusNotification | 1.3.6.1.4.1.35265.3.32.1 | |||
| NTF radiusRequestNotification | 1.3.6.1.4.1.35265.3.32.1.1 | Notification about request to server | ||
| I32 radiusSeqNum | 1.3.6.1.4.1.35265.3.5.10 | Integer32 | read-only | Sequence number of the request |
| I32 radiusStatus | 1.3.6.1.4.1.35265.3.5.11 | Integer32 | read-only | Completion status of the request |
| I32 radiusSwitchSrv | 1.3.6.1.4.1.35265.3.5.13 | Integer32 | read-only | Quantity indicator switch to the backup server |
| I32 radiusTimeout | 1.3.6.1.4.1.35265.3.5.12 | Integer32 | read-only | General timeout (in MS) to complete processing of the request (before receiving the server response or the completion of all attempts) |
| radiusTraps | 1.3.6.1.4.1.35265.3.32 | |||
| I32 radiusTypeResp | 1.3.6.1.4.1.35265.3.5.14 | Integer32 | read-only | The type of the server response |
| smgAlarm | 1.3.6.1.4.1.35265.3.29.1 | |||
| NTF smgAlarmCDRFileTrap | 1.3.6.1.4.1.35265.3.29.1.26 | Error while creating CDR-file state 0 - OK, 1 - commom alarm (can't create CDR file on disk), 3 - critical alarm (can't create CDR file) | ||
| NTF smgAlarmCdrFtpTrap | 1.3.6.1.4.1.35265.3.29.1.12 | No connection with FTP server Param1 0 No alarm, 2 - warning (minor alarm. The record was wrong, local CDR-data is less than 5 Mb), 1 - common (major alarm. The record was wrong, local CDR-data is more than 5 Mb and less than 15 Mb), 3 - critical (critical alarm. The record was wrong, local CDR-data is more than 15 Mb) (exState 0-ok 1-alarm 2-warning 3-critical) | ||
| NTF smgAlarmConfigTrap | 1.3.6.1.4.1.35265.3.29.1.1 | Configuration failure (exState 0-ok 3-critical) | ||
| NTF smgAlarmDriveLimitTrap | 1.3.6.1.4.1.35265.3.29.1.24 | Drive limit alarm param1: drive_id param2: (percent&0xFF << 8) | (exists & 0xFF) param3: free_size_kB Drive name at description text | ||
| NTF smgAlarmFansIdleTrap | 1.3.6.1.4.1.35265.3.29.1.23 | Fans idle alarm Par1 - fans operational bit-list Par2 - total fans operated Par3 - total fans on board | ||
| NTF smgAlarmH323NodeTrap | 1.3.6.1.4.1.35265.3.29.1.16 | No link to H323 adapter alarm (exState 0-ok 1-alarm) | ||
| NTF smgAlarmIpcOverloadTrap | 1.3.6.1.4.1.35265.3.29.1.51 | IPC overload (exState 0-ok 1-alarm) | ||
| NTF smgAlarmLinkSetTrap | 1.3.6.1.4.1.35265.3.29.1.4 | LinkSet alarm (exState 0-ok 3-critical) Param1 = LinkSet number | ||
| NTF smgAlarmMaintenanceTrap | 1.3.6.1.4.1.35265.3.29.1.18 | Maintenance alarm param1: 1 - COT test failed 2 - RLC-packet waiting error 3 - BLA-packet waiting error 4 - UBA-packet waiting error 5 - CGBA-packet waiting error 6 - CGUA-packet waiting error 7 - GRA-packet waiting error 8 - Error while blocking channels (CGBA) - not all of the requested channles were blocked 9 - Error while blocking channels (CGBA) - one of requested channels didn't blocked 10 - Error while blocking channels (CGUA) - not all of the requested channles were blocked 11 - Error while blocking channels (CGUA) - one of requested channels didn't blocked 12 - Error while get power voltage 13 - No free DVO blocks (param2 - subscriber group ID) param2 - E1 stream number, param3 - E1 channel number | ||
| NTF smgAlarmMegacoNodeTrap | 1.3.6.1.4.1.35265.3.29.1.27 | MEGACO-module alarm (exState 0-ok 3-critical) | ||
| NTF smgAlarmMemoryLimitTrap | 1.3.6.1.4.1.35265.3.29.1.13 | Param2 - free space, Param3 - summary space exState 0-ok, 2-warning (75% busy), 1-alarm (90%), 3-critical (95%) | ||
| NTF smgAlarmMspDevTrap | 1.3.6.1.4.1.35265.3.29.1.3 | SM-VP module alarm (exState 0-ok 1-alarm) Param1 - module number | ||
| NTF smgAlarmPowerModuleStateTrap | 1.3.6.1.4.1.35265.3.29.1.14 | exState 0 - ok, 2 - warning Param1 - PSU number Param2 - PSU state: 0 - OK, 1 - no power supply, 2 - missing | ||
| NTF smgAlarmProcOverloadTrap | 1.3.6.1.4.1.35265.3.29.1.21 | Processor overload exState 0-ok, 2-warning (load 90%), 1-alarm (95%) Par3 - CPU mask | ||
| NTF smgAlarmSbcRegistrationExpiredTrap | 1.3.6.1.4.1.35265.3.29.1.50 | sbc registration expired alarm. (no ok trap). abonent number in description | ||
| NTF smgAlarmSipAccessTrap | 1.3.6.1.4.1.35265.3.29.1.19 | SIP interface access alarm param1 - SIP interface number | ||
| NTF smgAlarmSipDuplicateTrap | 1.3.6.1.4.1.35265.3.29.1.31 | No SIP interface access alarm param1 - SIP interface number param2 - Destination IP-addr param3 - Destination port | ||
| NTF smgAlarmSipOptionsQueueOk | 1.3.6.1.4.1.35265.3.29.2.25 | SIP OPTIONS queue is OK | ||
| NTF smgAlarmSipOptionsQueueOverload | 1.3.6.1.4.1.35265.3.29.1.25 | SIP OPTIONS queue iverload | ||
| NTF smgAlarmSiptNodeTrap | 1.3.6.1.4.1.35265.3.29.1.2 | SIPT-module alarm (exState 0-ok 3-critical) | ||
| NTF smgAlarmSS7LinkTrap | 1.3.6.1.4.1.35265.3.29.1.6 | SS7-Link alarm (exState 0-ok 1-alarm) Param1 - E1Stream number Param2 - LinkSet number | ||
| NTF smgAlarmStreamTrap | 1.3.6.1.4.1.35265.3.29.1.5 | Stream alarm (exState 0-ok 2-warning 3-critical) Param1 - stream number Param2=1 - signal loss Param2=2 - remote alarm | ||
| NTF smgAlarmSyncTrap | 1.3.6.1.4.1.35265.3.29.1.7 | Synchronization alarm (freerun mode - work with local source) (exState 0-ok 1-alarm 2-warning), param1=1 - local param1=2 - less priority | ||
| NTF smgAlarmTemperatureTrap | 1.3.6.1.4.1.35265.3.29.1.17 | Tenperature alarm exState: 0 - ok, 2 - warning (more than 70 deg. Celsius), 1 - alarm (more than 85), 3 - critical-alarm (more than 100) param2 - temp #0 (CPU temp, generates alarm), param3 - temp #1 (RAM temp, for info only) | ||
| NTF smgCallForbiddenTrap | 1.3.6.1.4.1.35265.3.29.1.52 | Call forbidden info | ||
| NTF smgDemoLicenseTrap | 1.3.6.1.4.1.35265.3.29.1.30 | DEMO license status info param1 - Status 1 - inactive (ntp-off) 2 - inactive (ntp-nok) 3 - will expire in less than 72h 4 - will expire in less than 36h 5 - inactive (expired) 6 - inactive (error) | ||
| NTF smgFail2banBlockTrap | 1.3.6.1.4.1.35265.3.29.1.28 | Fail2ban address block info | ||
| NTF smgFirewallTrap | 1.3.6.1.4.1.35265.3.29.1.60 | Firewall info | ||
| smgOK | 1.3.6.1.4.1.35265.3.29.2 | |||
| NTF smgOkCallForbiddenTrap | 1.3.6.1.4.1.35265.3.29.2.52 | Call forbidden info | ||
| NTF smgOkCDRFileTrap | 1.3.6.1.4.1.35265.3.29.2.26 | No Error while creating CDR-file state 0 - OK, 1 - commom alarm (can't create CDR file on disk), 3 - critical alarm (can't create CDR file) | ||
| NTF smgOkCdrFtpTrap | 1.3.6.1.4.1.35265.3.29.2.12 | FTP server connection in norm | ||
| NTF smgOkConfigTrap | 1.3.6.1.4.1.35265.3.29.2.1 | NO Configuration failure | ||
| NTF smgOkDemoLicenseTrap | 1.3.6.1.4.1.35265.3.29.2.30 | DEMO license status info param1 - Status 0 - active | ||
| NTF smgOkDriveLimitTrap | 1.3.6.1.4.1.35265.3.29.2.24 | Drive limit OK Par1 - drive index Par2 - 1 - drive exist; 0 - removed Par3 - filling percentage Drive name at description text | ||
| NTF smgOkFansIdleTrap | 1.3.6.1.4.1.35265.3.29.2.23 | Fans idle OK Par1 - fans operational bit-list Par2 - total fans operated Par3 - total fans on board | ||
| NTF smgOkFirewallTrap | 1.3.6.1.4.1.35265.3.29.2.60 | Firewall info | ||
| NTF smgOkH323NodeTrap | 1.3.6.1.4.1.35265.3.29.2.16 | Link to H323 adapter is OK | ||
| NTF smgOkIpcOverloadTrap | 1.3.6.1.4.1.35265.3.29.2.51 | No IPC overload | ||
| NTF smgOkLinkSetTrap | 1.3.6.1.4.1.35265.3.29.2.4 | NO LinkSet alarm Param1 = LinkSet number | ||
| NTF smgOkMaintenanceTrap | 1.3.6.1.4.1.35265.3.29.2.18 | No maintenance alarm param1: MAINTENANCE_ALARM_SS7_COT_FAIL = 1 param2 - E1 stream number, param3 - E1 channel number | ||
| NTF smgOkMemoryLimitTrap | 1.3.6.1.4.1.35265.3.29.2.13 | No memory alarm Param2 - free space Param3 - summary space | ||
| NTF smgOkMspDevTrap | 1.3.6.1.4.1.35265.3.29.2.3 | NO SM-VP module alarm Param1 = module number | ||
| NTF smgOkPctlModuleTrap | 1.3.6.1.4.1.35265.3.29.2.58 | Packet control module info | ||
| NTF smgOkPortScanDetectorTrap | 1.3.6.1.4.1.35265.3.29.2.59 | Port scan detector info | ||
| NTF smgOkPowerModuleStateTrap | 1.3.6.1.4.1.35265.3.29.2.14 | PSU ok Param1 - PSU number Param2 - PSU state: 0 - OK, 1 - no power supply, 2 - missing | ||
| NTF smgOkProcOverloadTrap | 1.3.6.1.4.1.35265.3.29.2.21 | No proc overload | ||
| NTF smgOkRebootTrap | 1.3.6.1.4.1.35265.3.29.2.22 | Software started param1 = (version_major&0xFF) | ((version_minor&0xFF)<<8) | ((version_sub&0xFF)<<16) param2 = version_build param3 = reboot_cause (for SMG2016 only) 0 - power, 1 - software command, 2 - watchdog | ||
| NTF smgOkRegForbiddenTrap | 1.3.6.1.4.1.35265.3.29.2.53 | Registration forbidden info | ||
| NTF smgOkReserveSlaveLinkChangedTrap | 1.3.6.1.4.1.35265.3.29.2.55 | Reserve slave link info param2 = lan status param3 = wan status 0 - unlink, 1 - link | ||
| NTF smgOkReserveSlaveSoftVersionTrap | 1.3.6.1.4.1.35265.3.29.2.56 | Reserve soft version info | ||
| NTF smgOkSipAccessTrap | 1.3.6.1.4.1.35265.3.29.2.19 | No SIP interface access alarm param1 - SIP interface number | ||
| NTF smgOkSipAttackedTrap | 1.3.6.1.4.1.35265.3.29.2.57 | SIP attacked info | ||
| NTF smgOkSipDuplicateTrap | 1.3.6.1.4.1.35265.3.29.2.31 | SIP interface Duplicate alarm param1 - SIP interface number | ||
| NTF smgOkSIPinterfaceTrap | 1.3.6.1.4.1.35265.3.29.2.54 | SIP interface info | ||
| NTF smgOkSiptNodeTrap | 1.3.6.1.4.1.35265.3.29.2.2 | NO SIPT-module alarm | ||
| NTF smgOkSS7LinkTrap | 1.3.6.1.4.1.35265.3.29.2.6 | NO SS7-Link alarm: par1 - e1line, par2 - linkset | ||
| NTF smgOkStreamTrap | 1.3.6.1.4.1.35265.3.29.2.5 | NO Stream alarm Param1 - stream number | ||
| NTF smgOkSyncTrap | 1.3.6.1.4.1.35265.3.29.2.7 | NO Synchronization alarm (freerun mode - work with local source) | ||
| NTF smgOkTemperatureTrap | 1.3.6.1.4.1.35265.3.29.2.17 | No Temperature alarm Param2 - temp #0 CPU Param3 - temp #1 RAM | ||
| NTF smgOkTrunkGroupCPSTrap | 1.3.6.1.4.1.35265.3.29.2.29 | No CPS warning for the TrunkGroup param1 - TrunkGroup index param2 - CPS-warn threshold value param3 - Detected CPS value | ||
| NTF smgPctlModuleTrap | 1.3.6.1.4.1.35265.3.29.1.58 | Packet control module info | ||
| NTF smgPortScanDetectorTrap | 1.3.6.1.4.1.35265.3.29.1.59 | Port scan detector info | ||
| NTF smgRegForbiddenTrap | 1.3.6.1.4.1.35265.3.29.1.53 | Registration forbidden info | ||
| NTF smgReserveSlaveLinkChangedTrap | 1.3.6.1.4.1.35265.3.29.1.55 | Reserve slave link info param2 = lan status param3 = wan status 0 - unlink, 1 - link | ||
| NTF smgReserveSlaveSoftVersionTrap | 1.3.6.1.4.1.35265.3.29.1.56 | Reserve soft version info | ||
| NTF smgSipAttackedTrap | 1.3.6.1.4.1.35265.3.29.1.57 | SIP attacked info | ||
| NTF smgSIPinterfaceTrap | 1.3.6.1.4.1.35265.3.29.1.54 | SIP interface info | ||
| smgTraps | 1.3.6.1.4.1.35265.3.29 | |||
| NTF smgTrunkGroupCPSTrap | 1.3.6.1.4.1.35265.3.29.1.29 | TrunkGroup reached CPS warning threshold param1 - TrunkGroup index param2 - CPS-warn threshold value param3 - Detected CPS value | ||
| NTF smgUpdateFwFail | 1.3.6.1.4.1.35265.3.29.1.20 | descr = file + addr + FAIL | ||
| NTF smgUpdateFwOk | 1.3.6.1.4.1.35265.3.29.2.20 | descr = file + addr + OK |
FAQ
What alarm traps does ELTEX-SMI-ACTUAL define for Eltex voice and power hardware?
It defines fxs72AlarmTraps/fxs72OkTraps for FXS-72 voice port modules entering or clearing an alarm state, mxa32AlarmTraps/mxa32OkTraps for MXA32 access controller cards, and pp4AlarmTraps for PP4 power module faults, alongside PON/Teknovus line alarm conditions.
Why does an NMS need to load ELTEX-SMI-ACTUAL before it can properly receive Eltex FXS or power-module alarms?
ELTEX-SMI-ACTUAL defines the Eltex enterprise root OID tree and the alarm/notification branches for the FXS-72, MXA32, and PP4 modules, so the trap OIDs referenced by other Eltex MIBs can't be resolved or interpreted without this module being loaded first.
RFC description
Defines the Structure of Management Information (SMI) for Eltex Networks, providing the root OID tree and base definitions used by all other Eltex enterprise MIBs.
Start monitoring Eltex Networks access/PON equipment, e.g. MXA/FXS voice gateways, PON OLT/ONU (root SMI + alarm traps) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.