DKSF-50-8-1-A-X

All MIBs › DKSF-50-8-1-A-X

Organization: Alentis Electronics

Last Updated: 2010-04-14

Category: Domain: Environmental Monitoring, Vendor: NetPing/DKSF

Description: MIB for DKSF-50 NetPing device firmware 8.1 variant A providing sensor and relay management objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DKSF-50-8-1-A-X?

This is a generic NetPing MIB (used by the DKSF-50-8-1-A-X firmware variant) for remote sensing and control devices that combine IP-based power/relay control with environmental sensors. It exposes a power/relay control table for managing reset/reboot channels and a thermometer table for temperature sensor readings, alongside counters tracking how often resets have occurred. As a monitoring module it directly supports hardware status monitoring: tracking ambient/cabinet temperature via its thermal sensor inputs, and tracking the power-cycling behavior (manual mode, reset counts) of whatever equipment is plugged into its controlled outlets. It defines its own private object structure (npPwr, npThermo, lightcom) without an evident dependency on other standard MIBs beyond generic SNMP conventions. It is deployed in server rooms, comms cabinets, or remote sites where DKSF-50-8-1-A-X SNMP monitoring provides remote power-cycling control and basic environmental monitoring for connected equipment via a NetPing unit.

IPNetwork Monitor allows you to monitor SNMP objects defined in DKSF-50-8-1-A-X. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

NetPing DKSF-50-8-1-A-X IP-based remote power/relay and sensor controller

Monitoring Examples

Polling npThermoTable entries -- npThermoSensorN and npThermoValue -- lets an administrator track cabinet or ambient temperature per sensor channel and catch a cooling failure before it damages equipment. Separately, npPwrTable exposes per-channel control (npPwrChannelN, npPwrManualMode, npPwrStartReset) and reset counters (npPwrResetsCounter, npPwrRepeatingResetsCounter); a rapidly climbing npPwrRepeatingResetsCounter would indicate a connected device stuck in a boot loop that the NetPing unit keeps power-cycling.

What Can Be Monitored

temperature sensor readings
power/relay channel state
manual control mode
reset/reboot counters
repeating reset counter

Imported Objects

From RFC1155-SMI

enterprises

From SNMPv2-MIB

snmpTraps

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
mib-2

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using npRelHumSensorStatus OID:

Select a NetPing DKSF-50 IP-based remote power/relay and sensor controller as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type npRelHumSensorStatus into the Find box to locate it in the OID tree, then select it and click OK. Status of the Rel.Humidity Sensor One 0=Normal, 1=Error or Sensor isn't connected. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is anything other than 'ok', since that indicates the condition this object reports has changed to one worth investigating. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
lightcom	1.3.6.1.4.1.25728
netPing	1.3.6.1.4.1.25728.50			Generic MIB for NetPing remote sensing and control
npCurLoop	1.3.6.1.4.1.25728.8300
npCurLoopEntry	1.3.6.1.4.1.25728.8300.1.1		not-accessible	Current loop sensors Table Row
INT npCurLoopI	1.3.6.1.4.1.25728.8300.1.1.3	INTEGER	read-only	Loop current, mA
INT npCurLoopN	1.3.6.1.4.1.25728.8300.1.1.1	INTEGER	read-only	Index of current loop, 1 to max supported
INT npCurLoopPower	1.3.6.1.4.1.25728.8300.1.1.7	INTEGER	read-write	Control of loop power 0=Off, 1=On, 2=reset by off/on power
INT npCurLoopR	1.3.6.1.4.1.25728.8300.1.1.5	INTEGER	read-only	Resistance of the loop, Ohm
INT npCurLoopStatus	1.3.6.1.4.1.25728.8300.1.1.2	INTEGER	read-only	Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
npCurLoopTable	1.3.6.1.4.1.25728.8300.1		not-accessible	Current loop sensors Table
INT npCurLoopV	1.3.6.1.4.1.25728.8300.1.1.4	INTEGER	read-only	Voltage drop on the loop, mV
npIo	1.3.6.1.4.1.25728.8900
npIoEntry	1.3.6.1.4.1.25728.8900.1.1		not-accessible	Digital Input/output Table Row
INT npIoLevelIn	1.3.6.1.4.1.25728.8900.1.1.2	INTEGER	read-only	Input level, 0 or 1
INT npIoLevelOut	1.3.6.1.4.1.25728.8900.1.1.3	INTEGER	read-write	Output level, 0 or 1
INT npIoLineN	1.3.6.1.4.1.25728.8900.1.1.1	INTEGER	read-only	Number of IO line, from 1 to max supported
STR npIoMemo	1.3.6.1.4.1.25728.8900.1.1.6	DisplayString	read-only	IO line memo
npIoTable	1.3.6.1.4.1.25728.8900.1		not-accessible	Digital Input/output Table
npPwr	1.3.6.1.4.1.25728.5800
INT npPwrChannelN	1.3.6.1.4.1.25728.5800.3.1.1	INTEGER	read-only	The id of watchdog/power channel
npPwrEntry	1.3.6.1.4.1.25728.5800.3.1		not-accessible	Watchdog and outlet/relay control table row
INT npPwrManualMode	1.3.6.1.4.1.25728.5800.3.1.3	INTEGER	read-write	Mode of power channel 0 - manual off 1 - manual on 2 - watchdog
STR npPwrMemo	1.3.6.1.4.1.25728.5800.3.1.6	DisplayString	read-only	Watchdog/power channel memo
INT npPwrRepeatingResetsCounter	1.3.6.1.4.1.25728.5800.3.1.5	INTEGER	read-only	Counter of continous failed watchdog resets
INT npPwrResetsCounter	1.3.6.1.4.1.25728.5800.3.1.4	INTEGER	read-write	Counter of watchdog resets Write 0 to clear.
INT npPwrStartReset	1.3.6.1.4.1.25728.5800.3.1.2	INTEGER	read-write	Write 1 to start reset On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active
npPwrTable	1.3.6.1.4.1.25728.5800.3		not-accessible	Watchdog and outlet/relay control table
npRelHumidity	1.3.6.1.4.1.25728.8400
npRelHumSensor	1.3.6.1.4.1.25728.8400.2
INT npRelHumSensorStatusEx	1.3.6.1.4.1.25728.8400.2.3	INTEGER	read-only	Status of the Rel.Humidity Sensor One 0=Normal, 1=Error or Sensor isn't connected
INT npRelHumSensorValueH	1.3.6.1.4.1.25728.8400.2.2	INTEGER	read-only	Relative humidity value, %
INT npRelHumSensorValueT	1.3.6.1.4.1.25728.8400.2.4	INTEGER	read-only	Sensor temperature, deg.C
npThermo	1.3.6.1.4.1.25728.8800
npThermoEntry	1.3.6.1.4.1.25728.8800.1.1		not-accessible	Thermo Sensors Table Row
INT npThermoHigh	1.3.6.1.4.1.25728.8800.1.1.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoLow	1.3.6.1.4.1.25728.8800.1.1.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoMemo	1.3.6.1.4.1.25728.8800.1.1.6	DisplayString	read-only	T channel memo
INT npThermoSensorN	1.3.6.1.4.1.25728.8800.1.1.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoStatus	1.3.6.1.4.1.25728.8800.1.1.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
npThermoTable	1.3.6.1.4.1.25728.8800.1		not-accessible	Thermo Sensors Table
INT npThermoValue	1.3.6.1.4.1.25728.8800.1.1.2	INTEGER	read-only	Temperature, deg.C

RFC description

Generic MIB for NetPing remote sensing and control devices with power outlet/relay management.

Start monitoring NetPing DKSF-50 IP-based remote power/relay and sensor controller with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DKSF-50-8-1-A-X