DKSF-52-9-X-X-1

All MIBs › DKSF-52-9-X-X-1

Organization: Alentis Electronics

Last Updated: 2015-08-17

Category: Domain: Environmental Monitoring, Vendor: NetPing/DKSF

Description: MIB for the DKSF-52 NetPing device (firmware 9.x), supplying objects for relay control and remote environmental monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DKSF-52-9-X-X-1?

DKSF-52-9-X-X-1 is the private MIB for NetPing (DKSF-52 series) remote monitoring and control devices running firmware version 9.x, used for environmental sensing and relay-based equipment control in server rooms, cabinets, and remote sites. It exposes objects for controlling relay outputs, reading power/channel status, and configuring trap/email alerting for events. Its monitoring focus is squarely on hardware and environmental status: relay on/off state and mode, power channel status, and light/environmental sensor readings, plus the ability to trigger alerts (e.g., email notification) when a monitored condition changes. As a small vendor-specific device MIB, it has no notable dependency on other standard MIBs beyond the base SNMP framework. It is typically deployed in data-center or telecom-closet environments where DKSF-52-9-X-X-1 SNMP monitoring lets NetPing units provide remote power-cycling and environmental monitoring for otherwise unmanaged racks.

IPNetwork Monitor allows you to monitor SNMP objects defined in DKSF-52-9-X-X-1. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

NetPing DKSF-52 remote monitoring/relay control device

Monitoring Examples

Reading npRelayTable (via npRelayN, npRelayState, npRelayMode) tells an operator whether a given relay-controlled outlet or device is currently on or off, and npRelayFlip/npRelayStartReset can be used to power-cycle equipment remotely if it becomes unresponsive. The npPwrTable (npPwrChannelN) exposes per-channel power status, letting an admin detect a channel that has lost power, while npTrapEmailTo and npTrapInfo configure where alert emails are sent when such an event occurs.

What Can Be Monitored

relay on/off state
relay operating mode
power channel status
trap/alert email destination
relay reset/flip actions

Imported Objects

From SNMPv2-MIB

snmpTraps

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using npIoPulseCounter OID:

Select a NetPing DKSF-52 remote monitoring/relay control device as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type npIoPulseCounter into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the pulse Counter on IO input line (counts positive fronts) Write 0 to reset. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
lightcom	1.3.6.1.4.1.25728
netPing2PWR220	1.3.6.1.4.1.25728.52			Generic MIB for NetPing remote sensing and control
INT npForcedReboot	1.3.6.1.4.1.25728.911.3	INTEGER	read-write	Write 1 to immediate forced reboot
npIo	1.3.6.1.4.1.25728.8900
npIoEntry	1.3.6.1.4.1.25728.8900.1.1		not-accessible	Digital Input/output Table Row
INT npIoLevelIn	1.3.6.1.4.1.25728.8900.1.1.2	INTEGER	read-only	Input level, 0 or 1
INT npIoLevelOut	1.3.6.1.4.1.25728.8900.1.1.3	INTEGER	read-write	Output level
INT npIoLineN	1.3.6.1.4.1.25728.8900.1.1.1	INTEGER	read-only	Number of IO line, from 1 to max supported
STR npIoMemo	1.3.6.1.4.1.25728.8900.1.1.6	DisplayString	read-only	IO line memo
C32 npIoPulseCounterEx	1.3.6.1.4.1.25728.8900.1.1.9	Counter32	read-write	Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.
INT npIoSinglePulseDuration	1.3.6.1.4.1.25728.8900.1.1.12	INTEGER	read-write	Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms
INT npIoSinglePulseStart	1.3.6.1.4.1.25728.8900.1.1.13	INTEGER	read-write	Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration
npIoTable	1.3.6.1.4.1.25728.8900.1		not-accessible	Digital Input/output Table
NTF npIoTrap	1.3.6.1.4.1.25728.8900.2.0.1			Input state of IO line is changed
INT npIoTrapLevelIn	1.3.6.1.4.1.25728.8900.2.2	INTEGER	read-only	Trap data, new Input level, 0 or 1
INT npIoTrapLineN	1.3.6.1.4.1.25728.8900.2.1	INTEGER	read-only	Trap data, Number of IO line
STR npIoTrapMemo	1.3.6.1.4.1.25728.8900.2.6	DisplayString	read-only	Trap data, IO line memo
npIoTrapPrefix	1.3.6.1.4.1.25728.8900.2.0
npIoTraps	1.3.6.1.4.1.25728.8900.2
npIr	1.3.6.1.4.1.25728.7900
npIrCtrl	1.3.6.1.4.1.25728.7900.1
INT npIrPlayCmd	1.3.6.1.4.1.25728.7900.1.1	INTEGER	read-write	Write IR command number to send IR command
INT npIrReset	1.3.6.1.4.1.25728.7900.1.2	INTEGER	read-write	Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus.
INT npIrStatus	1.3.6.1.4.1.25728.7900.1.3	INTEGER	read-only	IR transiever status
npPwr	1.3.6.1.4.1.25728.5800
INT npPwrChannelN	1.3.6.1.4.1.25728.5800.3.1.1	INTEGER	read-only	The id of watchdog/power channel
npPwrEntry	1.3.6.1.4.1.25728.5800.3.1		not-accessible	Watchdog and outlet/relay control table row
INT npPwrManualMode	1.3.6.1.4.1.25728.5800.3.1.3	INTEGER	read-write	Mode of power channel 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - schedule and watchdog 5 - controlled by Logic
STR npPwrMemo	1.3.6.1.4.1.25728.5800.3.1.6	DisplayString	read-only	Relay channel memo
INT npPwrRelayFlip	1.3.6.1.4.1.25728.5800.3.1.14	INTEGER	read-write	Write -1 to flip between manual on and manual off states of relay
INT npPwrRelayState	1.3.6.1.4.1.25728.5800.3.1.15	INTEGER	read-only	Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on
INT npPwrRepeatingResetsCounter	1.3.6.1.4.1.25728.5800.3.1.5	INTEGER	read-only	Counter of continous failed watchdog resets
INT npPwrResetsCounter	1.3.6.1.4.1.25728.5800.3.1.4	INTEGER	read-write	Counter of watchdog resets Write 0 to clear.
INT npPwrStartReset	1.3.6.1.4.1.25728.5800.3.1.2	INTEGER	read-write	Write 1 to start forced reset On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active or watchdog is inactive
npPwrTable	1.3.6.1.4.1.25728.5800.3		not-accessible	Watchdog and outlet/relay control table
npReboot	1.3.6.1.4.1.25728.911
npRelay	1.3.6.1.4.1.25728.5500
npRelayEntry	1.3.6.1.4.1.25728.5500.5.1		not-accessible	Relay/outlet table row
INT npRelayFlip	1.3.6.1.4.1.25728.5500.5.1.14	INTEGER	read-only	Write -1 to flip between manual on and manual off states of relay
STR npRelayMemo	1.3.6.1.4.1.25728.5500.5.1.6	DisplayString	read-only	Relay memo
INT npRelayMode	1.3.6.1.4.1.25728.5500.5.1.2	INTEGER	read-write	Control of relay: 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logic
INT npRelayN	1.3.6.1.4.1.25728.5500.5.1.1	INTEGER	read-only	The N of output relay
INT npRelayStartReset	1.3.6.1.4.1.25728.5500.5.1.3	INTEGER	read-write	Write 1 to start reset (switch relay off for some time)
INT npRelayState	1.3.6.1.4.1.25728.5500.5.1.15	INTEGER	read-only	Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on
npRelayTable	1.3.6.1.4.1.25728.5500.5		not-accessible	Watchdog and outlet/relay control table
npRelHumidity	1.3.6.1.4.1.25728.8400
INT npRelHumSafeRangeHigh	1.3.6.1.4.1.25728.8400.2.7	INTEGER	read-only	Relative Humidity safe range, top margin, %RH
INT npRelHumSafeRangeLow	1.3.6.1.4.1.25728.8400.2.8	INTEGER	read-only	Relative Humidity safe range, bottom margin, %RH
npRelHumSensor	1.3.6.1.4.1.25728.8400.2
INT npRelHumSensorStatus	1.3.6.1.4.1.25728.8400.2.3	INTEGER	read-only	Status of the Rel.Humidity Sensor One 0=Normal, 1=Error or Sensor isn't connected
INT npRelHumSensorStatusH	1.3.6.1.4.1.25728.8400.2.5	INTEGER	read-only	Status of Relative Humiduty
INT npRelHumSensorValueH	1.3.6.1.4.1.25728.8400.2.2	INTEGER	read-only	Relative humidity value, %
INT npRelHumSensorValueT	1.3.6.1.4.1.25728.8400.2.4	INTEGER	read-only	Sensor temperature, deg.C
I32 npRelHumSensorValueT100	1.3.6.1.4.1.25728.8400.2.9	Integer32	read-only	Sensor temperature, deg.C * 100 (fixed point two decimal places) Used to get access to the fractional part of T value
NTF npRelHumTrap	1.3.6.1.4.1.25728.8400.9.0.1			Status of Relative Humidity RH sensor has changed!
npRelHumTrapPrefix	1.3.6.1.4.1.25728.8400.9.0
npRelHumTraps	1.3.6.1.4.1.25728.8400.9
INT npResetStack	1.3.6.1.4.1.25728.911.2	INTEGER	read-write	Write 1 to re-initialize network stack
INT npSoftReboot	1.3.6.1.4.1.25728.911.1	INTEGER	read-write	Write 1 to reboot device after current operations completition
npThermo	1.3.6.1.4.1.25728.8800
npThermoEntry	1.3.6.1.4.1.25728.8800.1.1		not-accessible	Thermo Sensors Table Row
INT npThermoHigh	1.3.6.1.4.1.25728.8800.1.1.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoLow	1.3.6.1.4.1.25728.8800.1.1.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoMemo	1.3.6.1.4.1.25728.8800.1.1.6	DisplayString	read-only	T channel memo
INT npThermoSensorN	1.3.6.1.4.1.25728.8800.1.1.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoStatus	1.3.6.1.4.1.25728.8800.1.1.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
npThermoTable	1.3.6.1.4.1.25728.8800.1		not-accessible	Thermo Sensors Table
NTF npThermoTrap	1.3.6.1.4.1.25728.8800.2.0.1			Status of Thermo sensor is changed (crossing of normal temp. range)
INT npThermoTrapHigh	1.3.6.1.4.1.25728.8800.2.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoTrapLow	1.3.6.1.4.1.25728.8800.2.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoTrapMemo	1.3.6.1.4.1.25728.8800.2.6	DisplayString	read-only	T channel memo
npThermoTrapPrefix	1.3.6.1.4.1.25728.8800.2.0
npThermoTraps	1.3.6.1.4.1.25728.8800.2
INT npThermoTrapSensorN	1.3.6.1.4.1.25728.8800.2.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoTrapStatus	1.3.6.1.4.1.25728.8800.2.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
INT npThermoTrapValue	1.3.6.1.4.1.25728.8800.2.2	INTEGER	read-only	Temperature, deg.C
INT npThermoValue	1.3.6.1.4.1.25728.8800.1.1.2	INTEGER	read-only	Temperature, deg.C
STR npTrapEmailTo	1.3.6.1.4.1.25728.90.1	DisplayString	read-only	user-specified e-mail for NetPing Trap Forwarding Service
npTrapInfo	1.3.6.1.4.1.25728.90

RFC description

MIB for DKSF-52 NetPing device firmware 9.x providing remote environmental monitoring and relay control objects.

Start monitoring NetPing DKSF-52 remote monitoring/relay control device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DKSF-52-9-X-X-1