DKSF-70-4-X-X-1

All MIBs › DKSF-70-4-X-X-1

Organization: Alentis Electronics

Last Updated: 2015-05-29

Category: Domain: Environmental Monitoring, Vendor: NetPing/DKSF

Description: MIB for DKSF-70 NetPing device firmware 4.x providing environmental sensor monitoring and relay control.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DKSF-70-4-X-X-1?

This MIB module belongs to NetPing, a Russian manufacturer of network-attached environmental sensing and relay-control devices, and it targets the DKSF-70 model running firmware version 4.x. It exposes data organized around two general categories: relay control outputs and thermal sensor inputs, alongside trap notification configuration. From a monitoring standpoint, it is used to track the hardware status of the device's temperature sensors (npThermoValue readings from up to several probes) and the operational state of its relays, which are often wired to door contacts, power switches, or environmental alarms. There is no strong dependency on other standard MIBs beyond the generic SNMPv2-SMI conventions, as this is a self-contained vendor MIB under the 'lightcom' enterprise branch. It is typically deployed in server rooms, telecom closets, or industrial cabinets where a small embedded device provides low-cost remote environmental monitoring and remote power/relay control over SNMP. Engineers can download the DKSF-70-4-X-X-1 file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DKSF-70-4-X-X-1. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

NetPing DKSF-70 environmental sensor/relay controller

Monitoring Examples

An administrator would poll npThermoTable/npThermoEntry columns such as npThermoSensorN and npThermoValue to track ambient temperature at each connected probe, alerting if a reading exceeds a safe threshold indicating cooling failure in a rack. The npRelayTable/npRelayEntry with npRelayState and npRelayMode lets the admin confirm whether a relay (e.g., controlling a fan, UPS bypass, or door lock) is currently open or closed and whether it is in automatic or manual mode. npTrapEmailTo and npTrapInfo configure where alert emails are sent when a threshold or relay state change trap fires, and npRelayStartReset lets an operator remotely cycle power on a stuck device.

What Can Be Monitored

thermal sensor temperature readings
relay open/closed state
relay operating mode
relay reset/power-cycle status
trap email notification target
number of active thermo sensors

Imported Objects

From SNMPv2-MIB

snmpTraps

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using npIoPulseCounter OID:

Select a NetPing DKSF-70 environmental sensor/relay controller as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type npIoPulseCounter into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the pulse Counter on IO input line (counts positive fronts) Write 0 to reset. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
lightcom	1.3.6.1.4.1.25728
npCurLoop	1.3.6.1.4.1.25728.8300
npCurLoopEntry	1.3.6.1.4.1.25728.8300.1.1		not-accessible	Current loop sensors Table Row
INT npCurLoopI	1.3.6.1.4.1.25728.8300.1.1.3	INTEGER	read-only	Loop current, mA
INT npCurLoopN	1.3.6.1.4.1.25728.8300.1.1.1	INTEGER	read-only	Index of current loop, 1 to max supported
INT npCurLoopPower	1.3.6.1.4.1.25728.8300.1.1.7	INTEGER	read-write	Control of loop power 0=Off, 1=On, 2=reset by off/on power
INT npCurLoopR	1.3.6.1.4.1.25728.8300.1.1.5	INTEGER	read-only	Resistance of the loop, Ohm
INT npCurLoopStatus	1.3.6.1.4.1.25728.8300.1.1.2	INTEGER	read-only	Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
npCurLoopTable	1.3.6.1.4.1.25728.8300.1		not-accessible	Current loop sensors Table
NTF npCurLoopTrap	1.3.6.1.4.1.25728.8300.2.0.1			Status of current loop N has changed!
INT npCurLoopTrapI	1.3.6.1.4.1.25728.8300.2.3	INTEGER	read-only	Loop current, mA
INT npCurLoopTrapN	1.3.6.1.4.1.25728.8300.2.1	INTEGER	read-only	Index of current loop, which status has changed
INT npCurLoopTrapPower	1.3.6.1.4.1.25728.8300.2.7	INTEGER	read-write	Status of loop power 0=Off, 1=On
npCurLoopTrapPrefix	1.3.6.1.4.1.25728.8300.2.0
INT npCurLoopTrapR	1.3.6.1.4.1.25728.8300.2.5	INTEGER	read-only	Resistance of the loop, Ohm
npCurLoopTraps	1.3.6.1.4.1.25728.8300.2
INT npCurLoopTrapStatus	1.3.6.1.4.1.25728.8300.2.2	INTEGER	read-only	Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
INT npCurLoopTrapV	1.3.6.1.4.1.25728.8300.2.4	INTEGER	read-only	Voltage drop on the loop, mV
INT npCurLoopV	1.3.6.1.4.1.25728.8300.1.1.4	INTEGER	read-only	Voltage drop on the loop, mV
INT npForcedReboot	1.3.6.1.4.1.25728.911.3	INTEGER	read-write	Write 1 to immediate forced reboot
npGsm	1.3.6.1.4.1.25728.3800
INT npGsmFailed	1.3.6.1.4.1.25728.3800.1.1	INTEGER	read-only	Firmware's GSM module status
npGsmInfo	1.3.6.1.4.1.25728.3800.1
INT npGsmRegistration	1.3.6.1.4.1.25728.3800.1.2	INTEGER	read-only	Status of modem registration in GSM network (AT+CREG? result)
STR npGsmSendSms	1.3.6.1.4.1.25728.3800.1.9	DisplayString	read-write	Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Only Latin characters allowed in message body
INT npGsmStrength	1.3.6.1.4.1.25728.3800.1.3	INTEGER	read-only	GSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating info
NTF npGsmTrap	1.3.6.1.4.1.25728.3800.2.0.1			GSM modem or SMS firmware problems
npGsmTrapPrefix	1.3.6.1.4.1.25728.3800.2.0
npGsmTraps	1.3.6.1.4.1.25728.3800.2
npIo	1.3.6.1.4.1.25728.8900
npIoEntry	1.3.6.1.4.1.25728.8900.1.1		not-accessible	Digital Input/output Table Row
INT npIoLevelIn	1.3.6.1.4.1.25728.8900.1.1.2	INTEGER	read-only	Input level, 0 or 1
INT npIoLevelOut	1.3.6.1.4.1.25728.8900.1.1.3	INTEGER	read-write	Output level, 0 or 1. Write -1 to flip output.
INT npIoLineN	1.3.6.1.4.1.25728.8900.1.1.1	INTEGER	read-only	Number of IO line, from 1 to max supported
STR npIoMemo	1.3.6.1.4.1.25728.8900.1.1.6	DisplayString	read-only	IO line memo
C32 npIoPulseCounterEx	1.3.6.1.4.1.25728.8900.1.1.9	Counter32	read-write	Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.
INT npIoSinglePulseDuration	1.3.6.1.4.1.25728.8900.1.1.12	INTEGER	read-write	Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms
INT npIoSinglePulseStart	1.3.6.1.4.1.25728.8900.1.1.13	INTEGER	read-write	Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration
npIoTable	1.3.6.1.4.1.25728.8900.1		not-accessible	Digital Input/output Table
NTF npIoTrap	1.3.6.1.4.1.25728.8900.2.0.1			Input state of IO line is changed
INT npIoTrapLevelIn	1.3.6.1.4.1.25728.8900.2.2	INTEGER	read-only	Trap data, new Input level, 0 or 1
STR npIoTrapLevelLegend	1.3.6.1.4.1.25728.8900.2.7	DisplayString	read-only	Legend for current logic level on the IO line
INT npIoTrapLineN	1.3.6.1.4.1.25728.8900.2.1	INTEGER	read-only	Trap data, Number of IO line
STR npIoTrapMemo	1.3.6.1.4.1.25728.8900.2.6	DisplayString	read-only	Trap data, IO line memo
npIoTrapPrefix	1.3.6.1.4.1.25728.8900.2.0
npIoTraps	1.3.6.1.4.1.25728.8900.2
npIr	1.3.6.1.4.1.25728.7900
npIrCtrl	1.3.6.1.4.1.25728.7900.1
INT npIrPlayCmd	1.3.6.1.4.1.25728.7900.1.1	INTEGER	read-write	Write IR command number to send IR command
INT npIrReset	1.3.6.1.4.1.25728.7900.1.2	INTEGER	read-write	Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus.
INT npIrStatus	1.3.6.1.4.1.25728.7900.1.3	INTEGER	read-only	IR transiever status
npReboot	1.3.6.1.4.1.25728.911
npRelay	1.3.6.1.4.1.25728.5500
npRelayEntry	1.3.6.1.4.1.25728.5500.5.1		not-accessible	Relay/outlet table row
STR npRelayMemo	1.3.6.1.4.1.25728.5500.5.1.6	DisplayString	read-only	Relay memo
INT npRelayMode	1.3.6.1.4.1.25728.5500.5.1.2	INTEGER	read-write	Control of relay: -1 - flip between on(1) and off(0) 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logic
INT npRelayN	1.3.6.1.4.1.25728.5500.5.1.1	INTEGER	read-only	The N of output relay
INT npRelayStartReset	1.3.6.1.4.1.25728.5500.5.1.3	INTEGER	read-write	Write 1 to start reset (switch relay off for some time)
INT npRelayState	1.3.6.1.4.1.25728.5500.5.1.15	INTEGER	read-only	Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on
npRelayTable	1.3.6.1.4.1.25728.5500.5		not-accessible	Watchdog and outlet/relay control table
npRelHumidity	1.3.6.1.4.1.25728.8400
INT npRelHumSafeRangeHigh	1.3.6.1.4.1.25728.8400.2.7	INTEGER	read-only	Relative Humidity safe range, top margin, %RH
INT npRelHumSafeRangeLow	1.3.6.1.4.1.25728.8400.2.8	INTEGER	read-only	Relative Humidity safe range, bottom margin, %RH
npRelHumSensor	1.3.6.1.4.1.25728.8400.2
INT npRelHumSensorStatus	1.3.6.1.4.1.25728.8400.2.3	INTEGER	read-only	Status of the Rel.Humidity Sensor One 1=Normal, 0=Error or Sensor isn't connected
INT npRelHumSensorStatusH	1.3.6.1.4.1.25728.8400.2.5	INTEGER	read-only	Status of Relative Humiduty
INT npRelHumSensorValueH	1.3.6.1.4.1.25728.8400.2.2	INTEGER	read-only	Relative humidity value, %
INT npRelHumSensorValueT	1.3.6.1.4.1.25728.8400.2.4	INTEGER	read-only	Sensor temperature, deg.C
I32 npRelHumSensorValueT100	1.3.6.1.4.1.25728.8400.2.9	Integer32	read-only	Sensor temperature, deg.C * 100 (fixed point two decimal places) Used to get access to the fractional part of T value
NTF npRelHumTrap	1.3.6.1.4.1.25728.8400.9.0.1			Status of Relative Humidity RH sensor has changed!
npRelHumTrapPrefix	1.3.6.1.4.1.25728.8400.9.0
npRelHumTraps	1.3.6.1.4.1.25728.8400.9
INT npResetStack	1.3.6.1.4.1.25728.911.2	INTEGER	read-write	Write 1 to re-initialize network stack
INT npSoftReboot	1.3.6.1.4.1.25728.911.1	INTEGER	read-write	Write 1 to reboot device after current operations completition
npThermo	1.3.6.1.4.1.25728.8800
npThermoEntry	1.3.6.1.4.1.25728.8800.1.1		not-accessible	Thermo Sensors Table Row
INT npThermoHigh	1.3.6.1.4.1.25728.8800.1.1.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoLow	1.3.6.1.4.1.25728.8800.1.1.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoMemo	1.3.6.1.4.1.25728.8800.1.1.6	DisplayString	read-only	T channel memo
INT npThermoSensorN	1.3.6.1.4.1.25728.8800.1.1.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoStatus	1.3.6.1.4.1.25728.8800.1.1.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
npThermoTable	1.3.6.1.4.1.25728.8800.1		not-accessible	Thermo Sensors Table
NTF npThermoTrap	1.3.6.1.4.1.25728.8800.2.0.1			Status of Thermo sensor is changed (crossing of normal temp. range)
INT npThermoTrapHigh	1.3.6.1.4.1.25728.8800.2.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoTrapLow	1.3.6.1.4.1.25728.8800.2.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoTrapMemo	1.3.6.1.4.1.25728.8800.2.6	DisplayString	read-only	T channel memo
npThermoTrapPrefix	1.3.6.1.4.1.25728.8800.2.0
npThermoTraps	1.3.6.1.4.1.25728.8800.2
INT npThermoTrapSensorN	1.3.6.1.4.1.25728.8800.2.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoTrapStatus	1.3.6.1.4.1.25728.8800.2.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
INT npThermoTrapValue	1.3.6.1.4.1.25728.8800.2.2	INTEGER	read-only	Temperature, deg.C
INT npThermoValue	1.3.6.1.4.1.25728.8800.1.1.2	INTEGER	read-only	Temperature, deg.C
STR npTrapEmailTo	1.3.6.1.4.1.25728.90.1	DisplayString	read-only	user-specified e-mail for NetPing Trap Forwarding Service
npTrapInfo	1.3.6.1.4.1.25728.90
uniPingServerSolutionV3	1.3.6.1.4.1.25728.70			Generic MIB for NetPing remote sensing and control

RFC description

Manages NetPing remote sensing and control devices with relay modes, IO lines, humidity sensors, and current loop monitoring.

Start monitoring NetPing DKSF-70 environmental sensor/relay controller with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DKSF-70-4-X-X-1