BLADETYPE2-PHYSICAL-MIB

All MIBs › BLADETYPE2-PHYSICAL-MIB

Organization: Hewlett Packard Company

Last Updated: 2003-12-05

Category: Hardware and Environment, Vendor: HP/HPE

Description: Reports physical hardware inventory and status for HP BladeSystem Type 2 blade modules.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BLADETYPE2-PHYSICAL-MIB?

BLADETYPE2-PHYSICAL-MIB is a switch-vendor MIB (associated with "Blade Type 2" series Layer 2 switching modules) whose available data covers Layer 2 configuration, statistics, and redundancy-link ("hotlinks") behavior rather than general chassis hardware inventory. It exposes data organized under layer2Configs, layer2Stats, and layer2Info branches, plus a dedicated hotlinks feature for automatic link failover between a primary and backup uplink port. In terms of monitoring, it is used to track hardware/software operational status of the switching fabric, specifically whether the current hotlinks configuration is active, whether forwarding-database updates are enabled, and whether an individual redundancy trigger has failed over (preempted) to its backup master port. It complements bridge/interface standards (BRIDGE-MIB, IF-MIB) by adding vendor-specific Layer 2 redundancy behavior not covered by those standards. Typical deployment is on managed Layer 2 switch blades in an enterprise or carrier access closet where uplink redundancy to a distribution switch must be monitored for correct failover. Engineers can download the BLADETYPE2-PHYSICAL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BLADETYPE2-PHYSICAL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Layer 2 managed switch / switch blade module (Blade Type 2 series)

Monitoring Examples

An operator would poll hotlinksCurCfgTriggerTable/hotlinksCurCfgTriggerEntry to check hotlinksCurCfgTriggerState and hotlinksCurCfgTriggerPreemptState for each configured trigger, confirming which port is currently the active hotlinksCurCfgTriggerMasterPort. A change in hotlinksCurCfgFdbUpdateState combined with a state flip on a trigger would reveal an uplink failover event, prompting investigation of the primary link. Comparing hotlinksCurCfgOnState against hotlinksNewCfgOnState also shows whether a pending configuration change has been applied.

What Can Be Monitored

hotlinks redundancy state
active vs backup master port
forwarding-database update status
trigger failover/preempt status
layer2 configuration and statistics

Imported Objects

From BRIDGE-MIB

BridgeId

From HP-SWITCH-PL-MIB

hpSwitchBladeType2-Mgmt

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
PhysAddress

How to Use in IPNetwork Monitor

Example using fdbStatsCreates OID:

Select a Layer 2 managed switches/blade module as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type fdbStatsCreates into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of entries created in the Forwarding Database. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT cistBridgeForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.11	INTEGER	read-only	The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root.
INT cistBridgeMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.10	INTEGER	read-only	The value in seconds that all bridges use for MaxAge when this bridge is acting as the root.
INT cistBridgePriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.9	INTEGER	read-only	The value of the writable portion of the Brigde Identifier comprising of the first two octets.
cistGeneralInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1
cistInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1
BRI cistInfoPortDesignatedBridge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.6	BridgeId	read-only	The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.
OCT cistInfoPortDesignatedPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.7	OCTET STRING	read-only	The Port identifier of the port on the Designated Bridge for this port's segment.
INT cistInfoPortHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.9	INTEGER	read-only	The amount of time between the transmission of Configuration Port PDUs in seconds.
I32 cistInfoPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.1	Integer32	read-only	The port number of the port for which this entry contains spanning tree configuration.
INT cistInfoPortLinkType	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.8	INTEGER	read-only	The point-to-point status of the LAN segment attached to this port. A value of p2p (2) indicates that this port is being treated as if it is connected to a point-to-point link. A value of shared(3) indicates that this port is being treated as having a shared media connection.
I32 cistInfoPortPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.3	Integer32	read-only	The contribution of this port to the path cost of paths towards the CIST Root which include this port.
I32 cistInfoPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.2	Integer32	read-only	The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value.
INT cistInfoPortRole	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.5	INTEGER	read-only	Selected Port Role of the port for this spanning tree instance.
INT cistInfoPortState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1.4	INTEGER	read-only	Current state of the Port as defined by the Common spanning tree protocol.
cistInfoPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2		not-accessible	The table of CIST Port information.
cistInfoPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.2.1		not-accessible	Information about a particular CIST Port.
INT cistMaxHopCount	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.12	INTEGER	read-only	Indicates the maximum hop count value.
I32 cistRegionalPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.8	Integer32	read-only	The Cost of the path to the CIST Regional Root as seen from this bridge.
BRI cistRegionalRoot	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.7	BridgeId	read-only	The bridge identifier of the Root of the Multiple spanning tree region as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Regional Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
BRI cistRoot	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.1	BridgeId	read-only	The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
I32 cistRootForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.6	Integer32	read-only	The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root.
I32 cistRootHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.4	Integer32	read-only	The amount of time between the transmission of Configuration bridge PDUs in seconds.
I32 cistRootMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.5	Integer32	read-only	The value in seconds that all bridges use for MaxAge when this bridge is acting as the root.
I32 cistRootPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.2	Integer32	read-only	The cost of the path to the CIST Root as seen from this bridge.
I32 cistRootPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.3	Integer32	read-only	The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge.
dot1pInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6
INT dot1pInfoPortCOSq	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.2.1.3	INTEGER	read-only	The 8021p port COSq.
dot1pInfoPortEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.2.1		not-accessible	Information about 8021p Port Priority
I32 dot1pInfoPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.2.1.1	Integer32	read-only	The 8021p Port number for which the table is related.
INT dot1pInfoPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.2.1.2	INTEGER	read-only	The 8021p Port number for which the table is related.
dot1pInfoPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.2		not-accessible	The table of 8021p port priority configuration in the Current_config.
INT dot1pInfoPortWeight	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.2.1.4	INTEGER	read-only	The 8021p port weight.
dot1pInfoPriorityCOSEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.1.1		not-accessible	Current information about 8021p priority to COS queue.
INT dot1pInfoPriorityCOSQueue	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.1.1.2	INTEGER	read-only	The 8021p priority COSq.
dot1pInfoPriorityCOSTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.1		not-accessible	The table of current priority to COS queue information.
INT dot1pInfoPriorityCOSWeight	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.1.1.3	INTEGER	read-only	The 8021p priority weight.
INT dot1pInfoPriorityIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.6.1.1.1	INTEGER	read-only	The 8021p priority for which the table is related.
dot1x	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11
INT dot1xCurCfgGlobalMaxRq	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.6	INTEGER	read-only	Maximum number of requests (1..10)
INT dot1xCurCfgGlobalMode	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.1	INTEGER	read-only	Autehtication Mode forceUnauth(0), auto(1), forceAuth(2)
INT dot1xCurCfgGlobalQtPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.2	INTEGER	read-only	Quiet period (0..65535)
INT dot1xCurCfgGlobalRaPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.7	INTEGER	read-only	Reauthentication period (0..604800)
INT dot1xCurCfgGlobalReAuth	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.8	INTEGER	read-only
INT dot1xCurCfgGlobalSrvTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.5	INTEGER	read-only	Server timeout (1..65535)
INT dot1xCurCfgGlobalSupTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.4	INTEGER	read-only	Supplicant timeout (1..65535)
dot1xCurCfgGlobalTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5
INT dot1xCurCfgGlobalTxPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.5.3	INTEGER	read-only	Tx period (1..65535)
dot1xCurCfgPortEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1		not-accessible	Information about 8021x Port Config
I32 dot1xCurCfgPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.1	Integer32	read-only	The 8021x Port number for which the table is related.
INT dot1xCurCfgPortMaxRq	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.7	INTEGER	read-only	Maximum numer of requests (1..10)
INT dot1xCurCfgPortMode	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.2	INTEGER	read-only	Port authenticaton mode forceUnauth(0), auto(1), forceAuth(2)
INT dot1xCurCfgPortQtPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.3	INTEGER	read-only	Quiet period (0-65535)
INT dot1xCurCfgPortRaPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.8	INTEGER	read-only	Reautentication period (0..604800)
INT dot1xCurCfgPortReAuth	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.9	INTEGER	read-only	ReAuthentication state off(0), on(1)
INT dot1xCurCfgPortSrvTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.6	INTEGER	read-only	Server timeout (1..65535)
INT dot1xCurCfgPortSupTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.5	INTEGER	read-only	Supplicant timeout (1..65535)
dot1xCurCfgPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3		not-accessible	The table of 8021x configuration in the Current_config.
INT dot1xCurCfgPortTxPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.3.1.4	INTEGER	read-only	Tx Period
INT dot1xCurStatus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.1	INTEGER	read-only	Dot1x status
dot1xInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5
INT dot1xInfoPortAuthMode	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1.1.2	INTEGER	read-only	Authentication mode
INT dot1xInfoPortAuthPAEState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1.1.5	INTEGER	read-only	Authenticator PAE State
INT dot1xInfoPortAuthStatus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1.1.3	INTEGER	read-only	Authentication status
INT dot1xInfoPortBackAuthState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1.1.6	INTEGER	read-only	Backend authenticator PAE state
INT dot1xInfoPortCtrlDir	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1.1.4	INTEGER	read-only	Controlled Directions
dot1xInfoPortEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1.1		not-accessible	Information about 8021x Port Config
I32 dot1xInfoPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1.1.1	Integer32	read-only	The 8021x Port number for which the table is related.
dot1xInfoPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.1		not-accessible	The table of 8021x configuration in the Current_config.
INT dot1xNewCfgGlobalMaxRq	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.6	INTEGER	read-create	Maximum number of requests (1..10)
INT dot1xNewCfgGlobalMode	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.1	INTEGER	read-create	Authentication Mode
INT dot1xNewCfgGlobalQtPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.2	INTEGER	read-create	Quiet Period (0..65535)
INT dot1xNewCfgGlobalRaPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.7	INTEGER	read-create	Reauthentication period (1..604800)
INT dot1xNewCfgGlobalReAuth	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.8	INTEGER	read-create	Reauthentication status
INT dot1xNewCfgGlobalSrvTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.5	INTEGER	read-create	Server timeout (1..65535)
INT dot1xNewCfgGlobalSupTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.4	INTEGER	read-create	Supplicand timeout (1..65535)
dot1xNewCfgGlobalTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6
INT dot1xNewCfgGlobalTxPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.6.3	INTEGER	read-create	Tx Period (1..65535)
INT dot1xNewCfgPortApplyGlobal	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.11	INTEGER	read-create	Apply Global config
INT dot1xNewCfgPortDefault	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.10	INTEGER	read-create	Port default settings
dot1xNewCfgPortEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1		not-accessible	Information about 8021x Port Config
I32 dot1xNewCfgPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.1	Integer32	read-only	The 8021x Port number for which the table is related.
INT dot1xNewCfgPortMaxRq	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.7	INTEGER	read-create	Maximum number of requests (1..10)
INT dot1xNewCfgPortMode	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.2	INTEGER	read-create	Port authentication mode forceUnauth(0), auto(1), forceAuth(2)
INT dot1xNewCfgPortQtPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.3	INTEGER	read-create	Quiet period (0..65535)
INT dot1xNewCfgPortRaPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.8	INTEGER	read-create	Reauthentication period (1..604800)
INT dot1xNewCfgPortReAuth	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.9	INTEGER	read-create	Reauthentication state off(0), on(1)
INT dot1xNewCfgPortSrvTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.6	INTEGER	read-create	Server Timeout (1..65535)
INT dot1xNewCfgPortSupTmout	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.5	INTEGER	read-create	Supplicant Timeout (1..65535)
dot1xNewCfgPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4		not-accessible	The table of 8021x configuration in the new_config.
INT dot1xNewCfgPortTxPeriod	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.4.1.4	INTEGER	read-create	Tx Period (1..65535)
INT dot1xNewStatus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.11.2	INTEGER	read-write	Dot1x status
INT dot1xSystemCapability	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.2.1	INTEGER	read-only	System capability
dot1xSystemInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.2
INT dot1xSystemProtoVersion	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.2.3	INTEGER	read-only	Protocol version
INT dot1xSystemStatus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.5.2.2	INTEGER	read-only	System status
fdb	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12
INT fdbClear	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.1	INTEGER	read-write	Setting this value to clear(2) clears the entire master FDB.
I32 fdbCurCfgAgingTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.1.1	Integer32	read-only	Fdb current aging time
fdbEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1		not-accessible	A row in the FDB table
fdbGeneralCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.1
fdbInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2
I32 fdbLearnedPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1.6	Integer32	read-only	The learned port associated with this FDB entry.
PHY fdbMacAddr	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1.1	PhysAddress	read-only	The MAC address for the FDB entry.
PHY fdbNewCfgAddMac	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.2.1.4	PhysAddress	read-create	Add a fdb entry.
I32 fdbNewCfgAddPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.2.1.3	Integer32	read-create	The MAC address port number.
I32 fdbNewCfgAddVlan	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.2.1.2	Integer32	read-create	Add vlan for fdb entry index
I32 fdbNewCfgAgingTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.1.2	Integer32	read-write	Fdb new aging time.
INT fdbNewCfgDelStaticEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.2.1.5	INTEGER	read-create	When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row.
I32 fdbNewCfgEntryIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.2.1.1	Integer32	read-only	The fdb entry index
fdbNewCfgStaticEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.2.1		not-accessible	A row in the fdb table.
fdbNewCfgStaticTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.12.2		not-accessible	The table of FDB static entries.
STR fdbRefSps	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1.5	DisplayString	read-only	The referenced SPs associated with this FDB entry.
I32 fdbSrcPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1.3	Integer32	read-only	Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address.
I32 fdbSrcTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1.7	Integer32	read-only	Either the value '0', or the trunk number of the trunk on which a frame having a source address equal to the value of the corresponding instance has been seen. A value of '0' indicates that the source address is not associated with a trunk.
INT fdbState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1.4	INTEGER	read-only	The state of the FDB entry. The meanings of the values are : unknown(1) : the MAC address has not yet been learned by the switch but has only been seen as a destination address forward(3) : the MAC address has been learned by the switch flood(4) : the MAC address is a multicast destination address trunk(6) : frames with this MAC address are forwarded to trunk group vir(7) : frames with this MAC address are forwarded for L3 processing
fdbStats	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1
C32 fdbStatsCreatesEx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.1	Counter32	read-only	Number of entries created in the Forwarding Database.
G32 fdbStatsCurrent	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.3	Gauge32	read-only	Current number of entries in the Forwarding Database.
C32 fdbStatsDeletes	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.2	Counter32	read-only	Number of entries deleted from the Forwarding Database.
C32 fdbStatsFindFails	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.8	Counter32	read-only	Number of search failures in the Forwarding Database.
C32 fdbStatsFindOrCreates	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.9	Counter32	read-only	Number of entries found or created in the Forwarding Database.
C32 fdbStatsFinds	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.7	Counter32	read-only	Number of searches in the Forwarding Database.
I32 fdbStatsHiwat	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.4	Integer32	read-only	Highest number of entries recorded at any given time in the Forwarding Database.
C32 fdbStatsLookupFails	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.6	Counter32	read-only	Number of unsuccessful searches made in the Forwarding Database.
C32 fdbStatsLookups	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.5	Counter32	read-only	Number of entry lookups in the Forwarding Database.
C32 fdbStatsOverflows	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.1.10	Counter32	read-only	Number of entries overflowing the Forwarding Database.
fdbTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2		not-accessible	The table of FDB entries.
I32 fdbVlan	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.2.2.1.2	Integer32	read-only	The VLAN ID for the FDB entry.
INT generalInfoStpUplinkFast	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.7.1	INTEGER	read-only	STP uplink fast mode
INT generalInfoUplinkFastRate	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.7.2	INTEGER	read-only	STP fast uplink rate.
genInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.7
hotlinksCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14
INT hotlinksCurCfgFdbUpdateState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.3	INTEGER	read-only	Enable/disable Hot Links FDB Update setting.
INT hotlinksCurCfgOnState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.1	INTEGER	read-only	Hot Links ON/OFF setting.
I32 hotlinksCurCfgTriggerBackupPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.7	Integer32	read-only	The backup interface port number.
I32 hotlinksCurCfgTriggerBackupTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.8	Integer32	read-only	The backup interface trunk number.
I32 hotlinksCurCfgTriggerFdelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.4	Integer32	read-only	Forward Delay setting (in secs).
I32 hotlinksCurCfgTriggerId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.1	Integer32	read-only	The Trigger identifier.
I32 hotlinksCurCfgTriggerMasterPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.5	Integer32	read-only	The master interface port number.
I32 hotlinksCurCfgTriggerMasterTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.6	Integer32	read-only	The master interface trunk number.
INT hotlinksCurCfgTriggerPreemptState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.3	INTEGER	read-only	Enable/disable Preemption state.
INT hotlinksCurCfgTriggerState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1.2	INTEGER	read-only	Enable/disable Trigger state.
hotlinksCurCfgTriggerTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6		not-accessible	The Hot Links Trigger Table.
hotlinksCurCfgTriggerTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.6.1		not-accessible	A row in the Hot Links Trigger Table.
hotlinksInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10
INT hotlinksInfoFdbUpdateState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.2	INTEGER	read-only	Enable/disable Hot Links FDB Update setting info.
INT hotlinksInfoOnState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.1	INTEGER	read-only	Hot Links ON/OFF setting info.
STR hotlinksInfoTriggerActive	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.3.1.5	DisplayString	read-only	A textual string containing the active interface info.
I32 hotlinksInfoTriggerFdelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.3.1.4	Integer32	read-only	Forward Delay setting info (in secs).
I32 hotlinksInfoTriggerId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.3.1.1	Integer32	read-only	The Trigger identifier.
INT hotlinksInfoTriggerPreemptState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.3.1.3	INTEGER	read-only	Enable/disable Preemption state info.
INT hotlinksInfoTriggerState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.3.1.2	INTEGER	read-only	Enable/disable Trigger state info.
hotlinksInfoTriggerTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.3		not-accessible	The Hot Links Trigger Table Info.
hotlinksInfoTriggerTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.10.3.1		not-accessible	A row in the Hot Links Trigger Table Info.
I32 hotlinksMaxTriggerEntries	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.5	Integer32	read-only	The maximum number of entries in the Hot Links Trigger Table.
INT hotlinksNewCfgFdbUpdateState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.4	INTEGER	read-write	Enable/disable Hot Links FDB Update setting.
INT hotlinksNewCfgOnState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.2	INTEGER	read-write	Hot Links ON/OFF settings.
I32 hotlinksNewCfgTriggerBackupPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.7	Integer32	read-write	The backup interface port number.
I32 hotlinksNewCfgTriggerBackupTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.8	Integer32	read-write	The backup interface trunk number.
I32 hotlinksNewCfgTriggerFdelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.4	Integer32	read-write	Forward Delay setting (in secs).
I32 hotlinksNewCfgTriggerId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.1	Integer32	read-only	The Trigger identifier.
I32 hotlinksNewCfgTriggerMasterPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.5	Integer32	read-write	The master interface port number.
I32 hotlinksNewCfgTriggerMasterTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.6	Integer32	read-write	The master interface trunk number.
INT hotlinksNewCfgTriggerPreemptState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.3	INTEGER	read-write	Enable/disable Preemption state.
INT hotlinksNewCfgTriggerState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1.2	INTEGER	read-write	Enable/disable Trigger state.
hotlinksNewCfgTriggerTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7		not-accessible	The Hot Links Trigger Table.
hotlinksNewCfgTriggerTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.14.7.1		not-accessible	A row in the Hot Links Trigger Table.
hotlinksStats	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6
I32 hotlinksStatsTriggerBackupActive	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6.1.1.3	Integer32	read-only	The number of times the backup interface was set to active.
I32 hotlinksStatsTriggerFdbFailed	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6.1.1.5	Integer32	read-only	The number of times an FDB update failed.
I32 hotlinksStatsTriggerFdbUpdate	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6.1.1.4	Integer32	read-only	The number of times an FDB update was performed.
I32 hotlinksStatsTriggerId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6.1.1.1	Integer32	read-only	The Trigger identifier.
I32 hotlinksStatsTriggerMasterActive	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6.1.1.2	Integer32	read-only	The number of times the master interface was set to active.
hotlinksStatsTriggerTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6.1		not-accessible	The Hot Links Trigger Table Stats.
hotlinksStatsTriggerTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.6.1.1		not-accessible	A row in the Hot Links Trigger Table Stats.
I32 illegalRx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.6	Integer32	read-only	Illegal subtype received
l2GeneralCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.8
INT l2ThashCurCfgDipState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.7	INTEGER	read-only	Enable or disable dip hash.
INT l2ThashCurCfgDmacState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.3	INTEGER	read-only	Enable or disable dmac hash.
INT l2ThashCurCfgSipState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.5	INTEGER	read-only	Enable or disable sip hash.
INT l2ThashCurCfgSmacState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.1	INTEGER	read-only	Enable or disable smac hash.
INT l2ThashNewCfgDipState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.8	INTEGER	read-write	Enable or disable dip hash.
INT l2ThashNewCfgDmacState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.4	INTEGER	read-write	Enable or disable dmac hash.
INT l2ThashNewCfgSipState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.6	INTEGER	read-write	Enable or disable sip hash.
INT l2ThashNewCfgSmacState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1.2	INTEGER	read-write	Enable or disable smac hash.
lacp	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6
INT lacpCurPortActorAdminKey	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.7.1.4	INTEGER	read-only	The current administrative value of the Key for the Aggregation Port. This is a 16-bit read-only value. The meaning of particular Key values is of local significance.
INT lacpCurPortActorPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.7.1.3	INTEGER	read-only	The priority value assigned to this Aggregation Port. This 16-bit value is read-only.
lacpCurPortCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.7		not-accessible	The table of LACP port configuration.
lacpCurPortCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.7.1		not-accessible	A row in the LACP port configuration table.
I32 lacpCurPortCfgTableId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.7.1.1	Integer32	read-only	LACP port number.
INT lacpCurPortState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.7.1.2	INTEGER	read-only	LACP port state can be one of three states off (Not participating in LACP) Active (Initiates LACPDU updates) Passive (Does not initiate LACPDU updates but responds to peer.
INT lacpCurSystemPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.1	INTEGER	read-only	A 2-octet read-write value indicating the priority value associated with the Actor's System ID.
INT lacpCurSystemTimeoutTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.5	INTEGER	read-only	If a port does not receive LACPDUs for Timeout time LACP information pertaining to the port is invalidated. Its every 3 sec (short) and every 90 sec (long 3).
I32 lacpdusRx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.2	Integer32	read-only	Valid LACPDUs received
I32 lacpdusTx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.7	Integer32	read-only	LACPDUs transmitted
lacpInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4
I32 lacpInfoPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4.1.1.1	Integer32	read-only	The port identifier.
INT lacpInfoPortMoved	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4.1.1.5	INTEGER	read-only	Port Moved flag is set to true if the receive machine for a port is in the port_disabled state, and the combination of partner oper system and partner oper port number in use by the port has been used by received in an incoming LACPDU on a different port.
INT lacpInfoPortNtt	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4.1.1.3	INTEGER	read-only	Need to transmit flag. True indicates that there is new protocol information that should be transmitted on the link.
INT lacpInfoPortReadyN	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4.1.1.4	INTEGER	read-only	True value for Ready_N flag indicates that the wait while timer has expired and it is waiting to attach to an aggregator. There is one Ready_N value for each port.
INT lacpInfoPortSelected	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4.1.1.2	INTEGER	read-only	Selected flag value indicates that the selection logic has selected an appropriate Aggregator. A value of unselected indicates that no aggregator is currently selected. A value of standby indicates that although the selection logic has selected an appropriate Aggregator, aggregation restrictions currently precent the port from being enabled as part of the aggregation, and so the port is being held in standby condition.
lacpInfoPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4.1		not-accessible	The table of LACP port information.
lacpInfoPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.4.1.1		not-accessible	Information about a LACP port.
INT lacpNewPortActorAdminKey	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.8.1.4	INTEGER	read-write	The current administrative value of the Key for the Aggregation Port. This is a 16-bit read-write value. The meaning of particular Key values is of local significance.
INT lacpNewPortActorPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.8.1.3	INTEGER	read-write	The priority value assigned to this Aggregation Port. This 16-bit value is read-write.
lacpNewPortCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.8		not-accessible	The table of LACP port configuration.
lacpNewPortCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.8.1		not-accessible	A row in the LACP port configuration table.
I32 lacpNewPortCfgTableId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.8.1.1	Integer32	read-only	LACP port number.
INT lacpNewPortState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.8.1.2	INTEGER	read-write	LACP port state can be one of three states off (Not participating in LACP) Active (Initiates LACPDU updates) Passive (Does not initiate LACPDU updates but responds to peer.
INT lacpNewSystemPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.2	INTEGER	read-write	A 2-octet read-write value indicating the priority value associated with the Actor's System ID.
INT lacpNewSystemTimeoutTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.6.6	INTEGER	read-write	If a port does not receive LACPDUs for Timeout time LACP information pertaining to the port is invalidated. Its every 3 sec (short) and every 90 sec (long 3).
lacpStats	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3
I32 lacpStatsIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.1	Integer32	read-only	Index
lacpStatsTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1		not-accessible	The table of LACP Stats.
lacpStatsTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1		not-accessible	Lacp status info.
layer2	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2			The MIB module for the Layer 2 configuration, statistics and information .
layer2Configs	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1
layer2Info	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3
layer2Oper	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.4
layer2Stats	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2
I32 markerpdusRx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.3	Integer32	read-only	Valid Marker PDUs received
I32 markerpdusTx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.8	Integer32	read-only	Market PDUs transmitted
I32 markerresponsepdusRx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.4	Integer32	read-only	Valid Marker Rsp PDUs received
I32 markerresponsepdusTx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.9	Integer32	read-only	Marker Rsp PDUs transmitted
mirroring	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4
mirrPortMirr	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1
mstCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5
mstCistBridgeCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2
mstCistCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2
INT mstCistCurCfgBridgeForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.7	INTEGER	read-only	The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root.
INT mstCistCurCfgBridgeMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.5	INTEGER	read-only	The value in seconds that all bridges use for MaxAge when this bridge is acting as the root.
INT mstCistCurCfgBridgePriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.1	INTEGER	read-only	The value of the writable portion of the Brigde Identifier comprising of the first two octets.
INT mstCistCurCfgPortEdge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1.5	INTEGER	read-only	The value of the Edge Port parameter.
INT mstCistCurCfgPortHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1.7	INTEGER	read-only	The amount of time between the transmission of Configuration Port PDUs in seconds.
I32 mstCistCurCfgPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1.1	Integer32	read-only	The port number of the port for which this entry contains spanning tree configuration.
INT mstCistCurCfgPortLinkType	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1.4	INTEGER	read-only	The administrative point-to-point status of the LAN segment attached to this port. A value of p2p (2) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of shared(3) indicates that this port should be treated as having a shared media connection. A value of auto(1) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
INT mstCistCurCfgPortPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1.3	INTEGER	read-only	The contribution of this port to the path cost of paths towards the CIST Root which include this port.
INT mstCistCurCfgPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1.2	INTEGER	read-only	The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value.
INT mstCistCurCfgPortStpState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1.6	INTEGER	read-only	Turn port's Spanning Tree on/off.
mstCistCurCfgPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3		not-accessible	The table of CIST Port configuration.
mstCistCurCfgPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.3.1		not-accessible	Information about a particular CIST Port configuration.
OCT mstCistCurCfgVlanBmap	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.9	OCTET STRING	read-only	The vlans applied to the CIST group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4094. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 9 \|\| \|\| \|\| \|\|___ vlan 8 \|\| \|____ vlan 7 \|\| . . . \|\|_________ vlan 2 \|__________ vlan 1 where x : 1 - The represented vlan applied to the CIST group. 0 - The represented vlan not applied to the group
INT mstCistDefaultCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.1	INTEGER	read-write	Setting the value to default(1) will set the Multiple Spanning Tree and member parameters to default. default(1) is always returned when read, but it does not mean anything.
I32 mstCistNewCfgAddVlan	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.11	Integer32	read-create	The vlan to be added to the CIST Group. A '0' value is returned when read.
INT mstCistNewCfgBridgeForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.8	INTEGER	read-write	The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root.
INT mstCistNewCfgBridgeMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.6	INTEGER	read-write	The value in seconds that all bridges use for MaxAge when this bridge is acting as the root.
INT mstCistNewCfgBridgePriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.2	INTEGER	read-write	The value of the writable portion of the Brigde Identifier comprising of the first two octets.
INT mstCistNewCfgPortEdge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1.5	INTEGER	read-create	The value of the Edge Port parameter.
INT mstCistNewCfgPortHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1.7	INTEGER	read-create	The amount of time between the transmission of Configuration Port PDUs in seconds.
I32 mstCistNewCfgPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1.1	Integer32	read-only	The port number of the port for which this entry contains spanning tree configuration.
INT mstCistNewCfgPortLinkType	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1.4	INTEGER	read-create	The administrative point-to-point status of the LAN segment attached to this port. A value of p2p (2) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of shared(3) indicates that this port should be treated as having a shared media connection. A value of auto(1) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
INT mstCistNewCfgPortPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1.3	INTEGER	read-create	The contribution of this port to the path cost of paths towards the CIST Root which include this port.
INT mstCistNewCfgPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1.2	INTEGER	read-create	The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value.
INT mstCistNewCfgPortStpState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1.6	INTEGER	read-create	Turn port's Spanning Tree on/off.
mstCistNewCfgPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4		not-accessible	The table of CIST Port configuration.
mstCistNewCfgPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.4.1		not-accessible	Information about a particular CIST Port configuration.
OCT mstCistNewCfgVlanBmap	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.2.2.10	OCTET STRING	read-only	The vlans applied to the CIST group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4094. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 9 \|\| \|\| \|\| \|\|___ vlan 8 \|\| \|____ vlan 7 \|\| . . . \|\|_________ vlan 2 \|__________ vlan 1 where x : 1 - The represented vlan applied to the CIST group. 0 - The represented vlan not applied to the group
INT mstCurCfgMaxHopCount	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.7	INTEGER	read-only	Indicates the maximum hop count value.
STR mstCurCfgRegionName	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.3	DisplayString	read-only	The Name for the Region's configuration.
INT mstCurCfgRegionVersion	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.5	INTEGER	read-only	Version of the MST Region.
INT mstCurCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.1	INTEGER	read-only	Enable or disable MSTP/RSTP
INT mstCurCfgStpMode	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.9	INTEGER	read-only	The version of Spanning Tree Protocal the bridge is currently running.
mstGeneralCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1
INT mstNewCfgMaxHopCount	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.8	INTEGER	read-write	Indicates the maximum hop count value.
STR mstNewCfgRegionName	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.4	DisplayString	read-write	The Name for the Region's configuration.
INT mstNewCfgRegionVersion	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.6	INTEGER	read-write	Version of the MST Region.
INT mstNewCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.2	INTEGER	read-write	Enable or disable MSTP/RSTP
INT mstNewCfgStpMode	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.5.1.10	INTEGER	read-write	The version of Spanning Tree Protocal the bridge is currently running.
STR mstpDigest	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.1.1.13	DisplayString	read-only	The digest of the mstp.
INT pmCurCfgPmirrDirection	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.3.1.3	INTEGER	read-only	The type of traffic to be monitored with respect to the mirrored port.
I32 pmCurCfgPmirrMirrPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.3.1.2	Integer32	read-only	The mirrored port number
I32 pmCurCfgPmirrMoniPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.3.1.1	Integer32	read-only	The monitoring port number.
INT pmCurCfgPortMirrState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.1	INTEGER	read-only	The state of port-based port mirroring.
pmCurCfgPortMonitorEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.3.1		not-accessible	A row in the monitoring port table.
pmCurCfgPortMonitorTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.3		not-accessible	The table of monitoring ports.
INT pmNewCfgPmirrDelete	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.4.1.4	INTEGER	read-create	Setting the value to delete(2) will delete the entire row. When read, other(1) is returned.
INT pmNewCfgPmirrDirection	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.4.1.3	INTEGER	read-create	The type of traffic to be monitored with respect to the mirrored port.
I32 pmNewCfgPmirrMirrPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.4.1.2	Integer32	read-only	The mirrored port number
I32 pmNewCfgPmirrMoniPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.4.1.1	Integer32	read-only	The monitoring port number.
INT pmNewCfgPmonDelete	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.4.1.10	INTEGER	read-create	Setting the value to delete(2) will delete the monitor port. When read, other(1) is returned.
INT pmNewCfgPortMirrState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.2	INTEGER	read-write	The state of port-based port mirroring.
pmNewCfgPortMonitorEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.4.1		not-accessible	A row in the monitoring port table.
pmNewCfgPortMonitorTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.4.1.4		not-accessible	The table of monitoring ports.
stgCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3
INT stgCurCfgAgingTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.9	INTEGER	read-only	The timeout period in seconds for aging out dynamically learned forwarding information.
INT stgCurCfgBrgForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.7	INTEGER	read-only	The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root.
INT stgCurCfgBrgHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.6	INTEGER	read-only	The value in seconds that all bridges use for HelloTime when this bridge is acting as the root.
INT stgCurCfgBrgMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.8	INTEGER	read-only	The value in seconds that all bridges use for MaxAge when this bridge is acting as the root.
I32 stgCurCfgIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.1	Integer32	read-only	The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB.
INT stgCurCfgPortEdge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.7	INTEGER	read-only	The state of port edge.
INT stgCurCfgPortFastFwd	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.8	INTEGER	read-only	The state of port fast forwarding.
I32 stgCurCfgPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.2	Integer32	read-only	The port identifier of a particular Spanning Tree Group.
INT stgCurCfgPortLink	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.6	INTEGER	read-only	The type of the port link.
INT stgCurCfgPortPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.5	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree root which include this port.
INT stgCurCfgPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.4	INTEGER	read-only	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
INT stgCurCfgPortState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.3	INTEGER	read-only	Turn on of off Spanning Tree operation of a particular port of a Spanning Tree Group.
stgCurCfgPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3		not-accessible	The table of Spanning Tree Group port configuration in the current_config.
stgCurCfgPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1		not-accessible	Information about port configuration of a particular Spanning Tree Group.
INT stgCurCfgPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.5	INTEGER	read-only	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID.
INT stgCurCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.2	INTEGER	read-only	Turn on of off Spanning Tree operation of a particular Spanning Tree Group.
I32 stgCurCfgStgIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.3.1.1	Integer32	read-only	The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB.
stgCurCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1		not-accessible	The table of Spanning Tree Group configuration.
stgCurCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1		not-accessible	Information about a particular Spanning Tree Group configuration.
OCT stgCurCfgVlanBmap	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.10	OCTET STRING	read-only	The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4095. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 9 \|\| \|\| \|\| \|\|___ vlan 8 \|\| \|____ vlan 7 \|\| . . . \|\|_________ vlan 2 \|__________ vlan 1 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree
OCT stgCurCfgVlanBmap1	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.3	OCTET STRING	read-only	The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 2048. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 9 \|\| \|\| \|\| \|\|___ vlan 8 \|\| \|____ vlan 7 \|\| . . . \|\|_________ vlan 2 \|__________ vlan 1 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree
OCT stgCurCfgVlanBmap2	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.1.1.4	OCTET STRING	read-only	The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 2049 to 4096. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 2057 \|\| \|\| \|\| \|\|___ vlan 2056 \|\| \|____ vlan 2055 \|\| . . . \|\|_________ vlan 2050 \|__________ vlan 2049 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree
OCT stgInfoVlanBmap	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.3	OCTET STRING	read-only	The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4096. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 9 \|\| \|\| \|\| \|\|___ vlan 8 \|\| \|____ vlan 7 \|\| . . . \|\|_________ vlan 2 \|__________ vlan 1 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree
I32 stgNewCfgAddVlan	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.4	Integer32	read-create	The vlan to be added to the specified Spanning Tree Group. A '0' value is returned when read.
INT stgNewCfgAgingTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.12	INTEGER	read-create	The timeout period in seconds for aging out dynamically learned forwarding information.
INT stgNewCfgBrgForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.10	INTEGER	read-create	The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root.
INT stgNewCfgBrgHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.9	INTEGER	read-create	The value in seconds that all bridges use for HelloTime when this bridge is acting as the root.
INT stgNewCfgBrgMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.11	INTEGER	read-create	The value in seconds that all bridges use for MaxAge when this bridge is acting as the root.
INT stgNewCfgDefaultCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.3	INTEGER	read-create	Setting the value to default-config(1) will set the default configuration as recommended by IEEE 802.1D for a particular Spanning Tree Group. default-config (1) is always returned When read, but it does not mean anything.
I32 stgNewCfgIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.1	Integer32	read-only	The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB.
INT stgNewCfgPortEdge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.7	INTEGER	read-create	The state of port edge.
INT stgNewCfgPortFastFwd	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.8	INTEGER	read-create	The state of port fast forwarding.
I32 stgNewCfgPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.2	Integer32	read-only	The port identifier of a particular Spanning Tree Group.
INT stgNewCfgPortLink	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.6	INTEGER	read-create	The type of the port link.
INT stgNewCfgPortPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.5	INTEGER	read-create	The contribution of this port to the path cost of paths towards the spanning tree root which include this port.
INT stgNewCfgPortPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.4	INTEGER	read-create	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
INT stgNewCfgPortState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.3	INTEGER	read-create	Turn on of off Spanning Tree operation of a particular port of a Spanning Tree Group.
stgNewCfgPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4		not-accessible	The table of Spanning Tree Group port configuration in the new_config.
stgNewCfgPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1		not-accessible	Information about port configuration of a particular Spanning Tree Group.
INT stgNewCfgPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.8	INTEGER	read-create	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID.
I32 stgNewCfgRemoveVlan	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.5	Integer32	read-create	The vlan to be removed from the specified Spanning Tree Group. A '0' value is returned when read.
INT stgNewCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.2	INTEGER	read-create	Turn on of off Spanning Tree operation of a particular Spanning Tree Group.
I32 stgNewCfgStgIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.4.1.1	Integer32	read-only	The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB.
stgNewCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2		not-accessible	The table of Spanning Tree Groups configuration in the new_config.
stgNewCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1		not-accessible	Information about a particular Spanning Tree Group configuration.
OCT stgNewCfgVlanBmap	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.13	OCTET STRING	read-only	The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4095. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 9 \|\| \|\| \|\| \|\|___ vlan 8 \|\| \|____ vlan 7 \|\| . . . \|\|_________ vlan 2 \|__________ vlan 1 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree
OCT stgNewCfgVlanBmap1	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.6	OCTET STRING	read-only	The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 2048. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 9 \|\| \|\| \|\| \|\|___ vlan 8 \|\| \|____ vlan 7 \|\| . . . \|\|_________ vlan 2 \|__________ vlan 1 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree
OCT stgNewCfgVlanBmap2	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.3.2.1.7	OCTET STRING	read-only	The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 2049 to 4096. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ vlan 2057 \|\| \|\| \|\| \|\|___ vlan 2056 \|\| \|____ vlan 2055 \|\| . . . \|\|_________ vlan 2050 \|__________ vlan 2049 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree
I32 stgStatsPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1.1.2	Integer32	read-only	The port identifier of a particular Spanning Tree Group.
C32 stgStatsPortRcvCfgBpdus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1.1.3	Counter32	read-only	Number of Configuration BPDU's received on this port.
C32 stgStatsPortRcvTcnBpdus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1.1.4	Counter32	read-only	Number of TCN BPDU's received on this port.
stgStatsPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1		not-accessible	The table of Spanning Tree Group port statistics.
stgStatsPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1.1		not-accessible	Statistics about port of a particular Spanning Tree Group.
C32 stgStatsPortXmtCfgBpdus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1.1.5	Counter32	read-only	Number of Configuration BPDU's trasmitted from the port.
C32 stgStatsPortXmtTcnBpdus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1.1.6	Counter32	read-only	Number of TCN BPDU's trasmitted from the port.
I32 stgStatsStpIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2.1.1.1	Integer32	read-only	The identifier of a particular Spanning Tree Group.
stpInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3
INT stpInfoAgingTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.17	INTEGER	read-only	The timeout period in seconds for aging out dynamically learned forwarding information.
INT stpInfoBrgForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.15	INTEGER	read-only	The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root.
INT stpInfoBrgHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.14	INTEGER	read-only	The value in seconds that all bridges use for HelloTime when this bridge is acting as the root.
INT stpInfoBrgMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.16	INTEGER	read-only	The value in seconds that all bridges use for MaxAge when this bridge is acting as the root.
INT stpInfoBrgPriority	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.13	INTEGER	read-only	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID.
BRI stpInfoDesignatedRoot	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.6	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
I32 stpInfoForwardDelay	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.11	Integer32	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database.
I32 stpInfoHelloTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.10	Integer32	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
I32 stpInfoHoldTime	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.12	Integer32	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
I32 stpInfoIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.1	Integer32	read-only	The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB.
I32 stpInfoMaxAge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.9	Integer32	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
BRI stpInfoPortDesignatedBridge	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.6	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
I32 stpInfoPortDesignatedCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.5	Integer32	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT stpInfoPortDesignatedPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.7	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
BRI stpInfoPortDesignatedRoot	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.4	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
C32 stpInfoPortForwardTransitions	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.8	Counter32	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
I32 stpInfoPortIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.2	Integer32	read-only	The port identifier of a particular Spanning Tree Group.
I32 stpInfoPortPathCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.9	Integer32	read-only	The path cost of the port.
INT stpInfoPortState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.3	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled, this object will have a value of disabled(1).
I32 stpInfoPortStpIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1.1	Integer32	read-only	The identifier of a particular Spanning Tree Group.
stpInfoPortTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2		not-accessible	The table of Spanning Tree Group port information.
stpInfoPortTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.2.1		not-accessible	Information about port configuration for a particular Spanning Tree Group.
I32 stpInfoRootCost	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.7	Integer32	read-only	The cost of the path to the root as seen from this bridge.
I32 stpInfoRootPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.8	Integer32	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
INT stpInfoState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.2	INTEGER	read-only	Turn on of off Spanning Tree operation of a particular Spanning Tree Group.
stpInfoTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1		not-accessible	The table of Spanning Tree Group information.
stpInfoTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1		not-accessible	Information about a particular Spanning Tree Group.
TIK stpInfoTimeSinceTopChange	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.4	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
C32 stpInfoTopChanges	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.3.1.1.5	Counter32	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
stpStats	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.2
thash	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7
thashL2	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.7.1
trunkgroup	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2
I32 trunkGroupCurCfgIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.2.1.1	Integer32	read-only	The identifier of the trunk group.
OCT trunkGroupCurCfgPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.2.1.2	OCTET STRING	read-only	The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to the trunk group 0 - The represented port does not belong to the trunk group
INT trunkGroupCurCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.2.1.3	INTEGER	read-only	Enable or disable a trunk group.
trunkGroupCurCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.2		not-accessible	The table of trunk group configuration.
trunkGroupCurCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.2.1		not-accessible	A row in the trunk group configuration table.
trunkGroupInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.9
I32 trunkGroupInfoIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.9.1.1.1	Integer32	read-only	The identifier of the trunk group.
OCT trunkGroupInfoPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.9.1.1.3	OCTET STRING	read-only	The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to the trunk group 0 - The represented port does not belong to the trunk group
INT trunkGroupInfoState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.9.1.1.2	INTEGER	read-only	Trunk group state.
trunkGroupInfoTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.9.1		not-accessible	The table of trunk group information.
trunkGroupInfoTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.9.1.1		not-accessible	A row in trunk group information table.
I32 trunkGroupNewCfgAddPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3.1.3	Integer32	read-create	The port to be added in the trunk group. When read, 0 is returned.
INT trunkGroupNewCfgDelete	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3.1.6	INTEGER	read-create	Setting the value to delete(2) will delete the entire row. When read, other(1) is returned.
I32 trunkGroupNewCfgIndex	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3.1.1	Integer32	read-only	The identifier of the trunk group.
OCT trunkGroupNewCfgPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3.1.2	OCTET STRING	read-only	The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to the trunk group 0 - The represented port does not belong to the trunk group
I32 trunkGroupNewCfgRemovePort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3.1.4	Integer32	read-create	The port to be deleted from the trunk group. when read, 0 is returned.
INT trunkGroupNewCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3.1.5	INTEGER	read-create	Enable or disable a trunk group.
trunkGroupNewCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3		not-accessible	The table of trunk group configuration.
trunkGroupNewCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.3.1		not-accessible	A row in the trunk group configuration table.
I32 trunkGroupTableMaxSize	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.2.1	Integer32	read-only	The maximum number of entries in trunk group table.
ufd	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9
INT ufdCurCfgGlobalState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.19	INTEGER	read-only	Current global Failover settings.
OCT ufdCurCfgLtDPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.7	OCTET STRING	read-only	The LtD port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to LtD 0 - The represented port does not belong to LtD
OCT ufdCurCfgLtDTrunks	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.9	OCTET STRING	read-only	The LtD trunk list. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ trunk 8 \|\| \|\| \|\| \|\|___ trunk 7 \|\| \|____ trunk 6 \|\| . . . \|\|_________ trunk 1 \|__________ reserved where x : 1 - The represented trunk belongs to LtD 0 - The represented trunk does not belong to LtD
OCT ufdCurCfgLtMPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.3	OCTET STRING	read-only	The LtM port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to LtM 0 - The represented port does not belong to LtM
OCT ufdCurCfgLtMTrunks	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.5	OCTET STRING	read-only	The LtM trunk list. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ trunk 8 \|\| \|\| \|\| \|\|___ trunk 7 \|\| \|____ trunk 6 \|\| . . . \|\|_________ trunk 1 \|__________ reserved where x : 1 - The represented trunk belongs to LtM 0 - The represented trunk does not belong to LtM
INT ufdCurCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.1	INTEGER	read-only	Enable or disable UFD state
ufdGeneralCfg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1
INT ufdNewCfgAddLtDPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.15	INTEGER	read-write	The port to be added to LtD. A '0' value is returned when read.
INT ufdNewCfgAddLtDTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.17	INTEGER	read-write	The trunk to be added to LtM. A '0' value is returned when read.
INT ufdNewCfgAddLtMPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.11	INTEGER	read-write	The port to be added to LtM. A '0' value is returned when read.
INT ufdNewCfgAddLtMTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.13	INTEGER	read-write	The trunk to be added to LtM. A '0' value is returned when read.
INT ufdNewCfgGlobalState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.20	INTEGER	read-write	New global Failover settings.
OCT ufdNewCfgLtDPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.8	OCTET STRING	read-write	The LtD port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to LtD 0 - The represented port does not belong to LtD
OCT ufdNewCfgLtDTrunks	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.10	OCTET STRING	read-write	The LtD trunk list. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ trunk 8 \|\| \|\| \|\| \|\|___ trunk 7 \|\| \|____ trunk 6 \|\| . . . \|\|_________ trunk 1 \|__________ reserved where x : 1 - The represented trunk belongs to LtD 0 - The represented trunk does not belong to LtD
OCT ufdNewCfgLtMPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.4	OCTET STRING	read-write	The LtM port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to LtM 0 - The represented port does not belong to LtM
OCT ufdNewCfgLtMTrunks	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.6	OCTET STRING	read-write	The LtM trunk list. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ trunk 8 \|\| \|\| \|\| \|\|___ trunk 7 \|\| \|____ trunk 6 \|\| . . . \|\|_________ trunk 1 \|__________ reserved where x : 1 - The represented trunk belongs to LtM 0 - The represented trunk does not belong to LtM
INT ufdNewCfgRemoveLtDPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.16	INTEGER	read-write	The port to be removed from LtM. A '0' value is returned when read.
INT ufdNewCfgRemoveLtDTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.18	INTEGER	read-write	The trunk to be removed from LtD. A '0' value is returned when read.
INT ufdNewCfgRemoveLtMPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.12	INTEGER	read-write	The port to be removed from LtM. A '0' value is returned when read.
INT ufdNewCfgRemoveLtMTrunk	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.14	INTEGER	read-write	The trunk to be removed from LtM. A '0' value is returned when read.
INT ufdNewCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.9.1.2	INTEGER	read-write	Enable or disable UFD state
I32 ufdNoLtDAutoDisabled	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.4.3	Integer32	read-only
I32 ufdNoLtMLinkBlockingState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.4.2	Integer32	read-only
I32 ufdNoLtMLinkFailure	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.4.1	Integer32	read-only
ufdStats	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.4
I32 unknownRx	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.2.3.1.1.5	Integer32	read-only	Unknown version/TLV type
INT updateCurCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.8.3	INTEGER	read-only	UplinkFast station update rate: packets per second
INT updateNewCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.8.4	INTEGER	read-write	UplinkFast station update rate: packets per second
INT upfastCurCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.8.1	INTEGER	read-only	Enable or disable uplink fast
INT upfastNewCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.8.2	INTEGER	read-write	Enable or disable uplink fast
vlan	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1
OCT vlanCurCfgPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.2.1.3	OCTET STRING	read-only	The port list in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to the VLAN 0 - The represented port does not belong to the VLAN
INT vlanCurCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.2.1.4	INTEGER	read-only	Enable or disable a VLAN
I32 vlanCurCfgStg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.2.1.6	Integer32	read-only	The Spanning Tree Group for the VLAN.
vlanCurCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.2		not-accessible	The table of VLAN configuration.
vlanCurCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.2.1		not-accessible	A row in the VLAN configuration table.
I32 vlanCurCfgVlanId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.2.1.1	Integer32	read-only	The VLAN identifier.
STR vlanCurCfgVlanName	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.2.1.2	DisplayString	read-only	The VLAN name.
vlanInfo	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.8
INT vlanInfoId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.8.1.1.1	INTEGER	read-only	The VLAN identifier.
STR vlanInfoName	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.8.1.1.2	DisplayString	read-only	The VLAN name.
OCT vlanInfoPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.8.1.1.4	OCTET STRING	read-only	The port list information in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to the VLAN 0 - The represented port does not belong to the VLAN
INT vlanInfoStatus	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.8.1.1.3	INTEGER	read-only	Enable or disable, VLAN state information
vlanInfoTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.8.1		not-accessible	The table of VLAN information.
vlanInfoTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.3.8.1.1		not-accessible	Information about a particular VLAN.
I32 vlanMaxEnt	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.1	Integer32	read-only	The maximum number of rows in the VLAN configuration table.
I32 vlanNewCfgAddPort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.5	Integer32	read-create	The port to be added to the specified VLAN. A '0' value is returned when read.
INT vlanNewCfgDelete	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.7	INTEGER	read-create	This is an action object to create or delete a VLAN. other(1) is returned always when read. The following values are writable: delete(2)...to delete a VLAN
OCT vlanNewCfgPorts	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.3	OCTET STRING	read-only	The port list in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... \|\| \|\| \|_ port 8 \|\| \|\| \|\| \|\|___ port 7 \|\| \|____ port 6 \|\| . . . \|\|_________ port 1 \|__________ reserved where x : 1 - The represented port belongs to the VLAN 0 - The represented port does not belong to the VLAN
I32 vlanNewCfgRemovePort	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.6	Integer32	read-create	The port to be removed from the specified VLAN. A '0' value is returned when read.
INT vlanNewCfgState	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.4	INTEGER	read-create	Enable or disable a VLAN
I32 vlanNewCfgStg	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.9	Integer32	read-create	The Spanning Tree Group for the VLAN.
vlanNewCfgTable	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3		not-accessible	The table of VLAN configuration.
vlanNewCfgTableEntry	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1		not-accessible	A row in the VLAN configuration table.
I32 vlanNewCfgVlanId	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.1	Integer32	read-only	The VLAN identifier.
STR vlanNewCfgVlanName	1.3.6.1.4.1.11.2.3.7.11.33.1.2.2.1.1.3.1.2	DisplayString	read-create	The VLAN name.

RFC description

Manages Layer 2 configuration, VLAN, spanning tree, and physical port settings on HP blade switches.

Start monitoring Layer 2 managed switches/blade modules with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BLADETYPE2-PHYSICAL-MIB