All MIBs › HPICF-IPSLA-MIB
Organization: HP Networking.
Last Updated: 2016-11-10
Category: Technology: Network Monitoring, Technology: OAM, Technology: SLA/OAM, Vendor: HP/HPE
Description: HP ICF SNMP MIB for IP SLA probe configuration and performance measurement results on HP ProCurve network devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HPICF-IPSLA-MIB?
HPICF-IPSLA-MIB is an HP (ICF, Internet Common Firmware) proprietary MIB for configuring and monitoring IP Service Level Agreement (SLA) probes on HP ProCurve/Aruba-branded managed network devices. It exposes probe configuration such as probe type, administrative state, source/destination address and port, and source interface, used to actively measure network performance (e.g., latency, jitter, packet loss) between devices. For hardware/software status monitoring it primarily reflects operational software state — hpicfIpSlaAdminState shows whether a given probe is enabled — and its associated (though not sampled here) result objects would carry the actual performance metrics collected by each probe. It builds on the same conceptual model as Cisco's IP SLA and the IETF's disman-ping-mib work, though as an HP proprietary MIB it is independent of those standards. It is deployed in enterprise networks where HP switches/routers run active performance probes to verify SLA compliance between sites. Engineers can download the HPICF-IPSLA-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HPICF-IPSLA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP ProCurve/networking managed switch or router
Monitoring Examples
An administrator would configure hpicfIpSlaTable/hpicfIpSlaEntry with hpicfIpSlaType, hpicfIpSlaSourceAddress/hpicfIpSlaSourceInterface, and hpicfIpSlaDestAddress/hpicfIpSlaL4DestPort to set up a probe from one site to another, then poll hpicfIpSlaAdminState to confirm the probe is active. hpicfIpSlaNotifications would alert if a probe transitions state unexpectedly, such as failing to reach its destination, which would indicate a path outage or SLA breach between the source and destination addressed in the table.
What Can Be Monitored
- IP SLA probe admin state
- probe type
- source/destination address and port
- source interface
- SLA notification events
This MIB depends on
Related MIBs
Imported Objects
From HP-ICF-OID
| hpSwitch | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndexOrZero |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType | |
| InetPortNumber |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| RowStatus |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hpicfIpSla | 1.3.6.1.4.1.11.2.14.11.5.1.127 | This MIB module contains HP proprietary objects for managing IP Service Level Agreement (SLA). | ||
| hpicfIpSlaNotifications | 1.3.6.1.4.1.11.2.14.11.5.1.127.0 | |||
| NTF hpicfIpSlaThresholdexceeded | 1.3.6.1.4.1.11.2.14.11.5.1.127.0.1 | This notification is generated when the metric calculated from the SLA result exceeds the configured threshold value. The hpicfIpSlaThrUpper is not applicable when hpicfIpSlaThrMetricType is set to packetLoss or testCompletion. | ||
| NTF hpicfIpSlaTestCompletion | 1.3.6.1.4.1.11.2.14.11.5.1.127.0.2 | This notification is generated when the SLA test is completed either by reaching stopTime or hpicfIpSlaAttrNumPkts. This notification is sent only when the action type is set to trap or trap-log. | ||
| NTF hpicfIpSlaThresholdPktLoss | 1.3.6.1.4.1.11.2.14.11.5.1.127.0.3 | This notification is generated when SLA test probe reply packets are lost consecutively for the configured number of hpicfIpSlaThrCount. This notification is sent only when the action type is set to trap or trap-log. | ||
| hpicfIpSlaObjects | 1.3.6.1.4.1.11.2.14.11.5.1.127.1 | |||
| hpicfIpSlaTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1 | not-accessible | This table specifies IP SLA test parameters as SLA entries. | |
| hpicfIpSlaEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1 | not-accessible | An entry on this table specifies the destination IP address/ Hostname, Source address, Source Interface ID & Row status corresponding to each SLA test. | |
| I32 hpicfIpSlaID | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.1 | Integer32 | not-accessible | This is an identifier for the IP SLA. |
| INT hpicfIpSlaType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.2 | INTEGER | read-create | SLA Probe Type. IcmpEcho is similar to ping protocol and the destination should be enabled with responder functionality for udpEcho, udpJitter, udpJitterVoIP and tcpConnect. For DHCP and DNS, destination device should be enabled with DHCP and DNS servers, respectively. |
| INT hpicfIpSlaAdminState | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.3 | INTEGER | read-create | Enable or disable the IP Service Level Agreement (SLA) probe. |
| IPt hpicfIpSlaSourceAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.4 | InetAddressType | read-create | SLA source address type. |
| IP hpicfIpSlaSourceAddress | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.5 | InetAddress | read-create | SLA source address. |
| INE hpicfIpSlaL4SourcePort | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.6 | InetPortNumber | read-create | SLA source port to be used for SLA probes that use a transport layer such as udpEcho, udpJitter, udpJitterVoIP and tcpConnect. The allowed range is from 1024 to 65535. |
| NUM hpicfIpSlaSourceInterface | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.7 | InterfaceIndexOrZero | read-create | SLA source interface. |
| IPt hpicfIpSlaDestAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.8 | InetAddressType | read-create | SLA destination address type. |
| IP hpicfIpSlaDestAddress | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.9 | InetAddress | read-create | SLA destination address. |
| INE hpicfIpSlaL4DestPort | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.10 | InetPortNumber | read-create | Port on target device which responds back to the probe. This is used for SLA probes that use a transport layer such as udpEcho, udpJitter, udpJitterVoIP and tcpConnect SLA types. The allowed range is from 1024 to 65535. |
| ROW hpicfIpSlaRowStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.11 | RowStatus | read-create | SLA row status. |
| hpicfIpSlaAttrTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2 | not-accessible | This table specifies IP SLA test parameters as SLA entries. | |
| hpicfIpSlaAttrEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1 | not-accessible | An entry on this table specifies the attributes of SLA test such as scheduling parameters, TOS, payload size, history bucket size and inter packet interval, corresponding to each SLA test. | |
| DAT hpicfIpSlaSchedStartTime | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.1 | DateAndTime | read-create | Timestamp to denote when to start this SLA probe. |
| DAT hpicfIpSlaSchedEndTime | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.2 | DateAndTime | read-create | Timestamp to denote when to end this SLA probe. |
| U32 hpicfIpSlaSchedFreq | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.3 | Unsigned32 | read-create | Frequency in seconds. This value is used to send probes. |
| U32 hpicfIpSlaSchedRepeat | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.4 | Unsigned32 | read-create | Number of times this test will be repeated. |
| U32 hpicfIpSlaAttrTOS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.5 | Unsigned32 | read-create | Type of service value to be set for the probe packet. |
| U32 hpicfIpSlaAttrHistorySize | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.6 | Unsigned32 | read-create | Number of history records to be maintained for SLA test. Size can vary from 1 to 50. |
| U32 hpicfIpSlaAttrPayloadSize | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.7 | Unsigned32 | read-create | Size of the packet payload to be sent out for each probe. It can be set from 0 to 1440 for udpEcho, icmpEcho and from 68 to 8100 for udpJitter. |
| U32 hpicfIpSlaAttrNumPkts | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.8 | Unsigned32 | read-create | Number of packets to be sent out for a single probe for jitter SLA type. |
| U32 hpicfIpSlaAttrPktInterval | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.9 | Unsigned32 | read-create | Inter packet interval in milli seconds. Which is to be used for packets that are sent out for a single probe for jitter SLA type. |
| ROW hpicfIpSlaAttrRowStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.10 | RowStatus | read-create | SLA attribute row status. |
| INT hpicfIpSlaAttrCodecType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.11 | INTEGER | read-create | Codec-type for the VoIP SLA test. |
| U32 hpicfIpSlaAttrAdvntgFactr | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.12 | Unsigned32 | read-create | Advantage factor to calculate the MOS and ICPIF values for VoIP SLA type. |
| hpicfIpSlaThrTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3 | not-accessible | This table specifies IP SLA threshold-action parameters as entries. When one of the monitored parameters of an SLA test goes beyond the configured thresholds, notifications are generated either as traps or syslog messages. | |
| hpicfIpSlaThrEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1 | not-accessible | An entry on this table specifies the Metric type, upper and lower limit of thresholds, threshold type and action to be taken. | |
| INT hpicfIpSlaThrMetricType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.1 | INTEGER | not-accessible | SLA metric type to be monitored. The rtt type is the round trip time of the probe packet. The jitter type is the inter-packet delay variance. The srcTodstTime type is the one-way trip time from source to destination. The dstTosrcTtime type is the one-way trip time from destination to source. The Mean Opinion Scores (MOS) type is derived only for udpJitterVoIP SLA. The Calculated Planning Impairment Factor (ICPIF) type is derived only for udpJitterVoIP SLA. ThepacketLoss type is to monitor loss of communication. The testCompletion type is for notifying about the completion of probe test. The sdJitterPos type is the source-to-destination positive jitter and the dsJitterPos type is the destination-to-source positivejitter. |
| I32 hpicfIpSlaThrUpper | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.2 | Integer32 | read-create | Acceptable upper-limit of threshold value for SLA. This value is not applicable when hpicfIpSlaThrMetricType is set to packetLoss and testCompletion. |
| I32 hpicfIpSlaThrLower | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.3 | Integer32 | read-create | Acceptable lower-limit of threshold value for SLA. This value is not applicable when hpicfIpSlaThrMetricType is set to packetLoss and testCompletion. |
| INT hpicfIpSlaThrType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.4 | INTEGER | read-create | Configure threshold type to trigger action. When a trap/log has to be generated each time the threshold is breached, immediate threshold type can be used. The Consecutive threshold type generates traps/logs when the threshold is violated a certain number of times This value is not applicable when hpicfIpSlaThrMetricType is set to testCompletion. The aggregated threshold type is used to generate traps/logs for aggregated probes. |
| U32 hpicfIpSlaThrCount | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.5 | Unsigned32 | read-create | The value for the number of consecutive times the upper or lower limit of the threshold is violated. For example, this can be configured to trigger a trap/log when the RTT is more than the upper limit, x number of times consecutively. This value is applicable only if hpicfIpSlaThrType is set to consecutive. |
| INT hpicfIpSlaThrAction | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.6 | INTEGER | read-create | The number of probe packets used to calculate Round Trip Time for jitter test. |
| ROW hpicfIpSlaThrRowStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.7 | RowStatus | read-create | Threshold table row status. |
| hpicfIpSlaRespTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.4 | not-accessible | This table specifies IP SLA responder parameters as entries. | |
| hpicfIpSlaRespEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1 | not-accessible | An entry on this table specifies the local IP address, port number and row status corresponding to each SLA responder config. | |
| INT hpicfIpSlaRespType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.1 | INTEGER | not-accessible | The SLA responder type. The udpEcho and tcpConnect objects are for UDP and TCP packets, respectively. The udpJitter and udpJitterVoIP values calculate one-way delay, therefore a timestamp has to be embedded while replying back. This is one of the indexes for the hpicfIpSlaRespTable. |
| IPt hpicfIpSlaRespAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.2 | InetAddressType | read-create | SLA responder IP address type. |
| IP hpicfIpSlaRespAddress | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.3 | InetAddress | not-accessible | The local IP address to which the responder is bound. This is one of the indexes for the hpicfIpSlaRespTable. |
| INE hpicfIpSlaRespL4Port | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.4 | InetPortNumber | not-accessible | L4 port number on hpicfIpSlaRespAddress where the responder listens for probe packets from SLA source. This is one of the indexes for the hpicfIpSlaRespTable. The allowed range is from 1024 to 65535. |
| ROW hpicfIpSlaRespRowStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.5 | RowStatus | read-create | SLA responder row status. |
| hpicfIpSlaMsgTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5 | not-accessible | This table specifies the IP SLA result parameters as entries. | |
| hpicfIpSlaMsgEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1 | not-accessible | An entry on this table specifies the probe received time, probe error counters and threshold hit counter. | |
| U32 hpicfIpSlaMsgLastProbeRcvd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.1 | Unsigned32 | read-only | Last probe received time. |
| U32 hpicfIpSlaMsgLastClrRec | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.2 | Unsigned32 | read-only | Last clear record done time. |
| U32 hpicfIpSlaMsgSuccProbe | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.3 | Unsigned32 | read-only | Number of successful probes. |
| U32 hpicfIpSlaMsgIntErr | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.4 | Unsigned32 | read-only | Internal error count. |
| U32 hpicfIpSlaMsgLocIntfDown | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.5 | Unsigned32 | read-only | Number of probes failed due to local interface failure. |
| U32 hpicfIpSlaMsgResTimeout | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.6 | Unsigned32 | read-only | Resolution timed out. |
| U32 hpicfIpSlaMsgDNSFormatErr | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.7 | Unsigned32 | read-only | Number of DNS format errors. |
| U32 hpicfIpSlaMsgServerFaild | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.8 | Unsigned32 | read-only | Number of server failed errors. |
| U32 hpicfIpSlaMsgDomainNotExist | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.9 | Unsigned32 | read-only | Number of domain does not exist errors. |
| U32 hpicfIpSlaMsgFunctnNotImpl | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.10 | Unsigned32 | read-only | Number of function not implemented errors. |
| U32 hpicfIpSlaMsgServerRefusd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.11 | Unsigned32 | read-only | Number of server refused errors. |
| U32 hpicfIpSlaMsgNameNotExist | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.12 | Unsigned32 | read-only | Number of name does not exist errors. |
| U32 hpicfIpSlaMsgRRsetNotExist | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.13 | Unsigned32 | read-only | Number of RRset that should not exist errors. |
| U32 hpicfIpSlaMsgServerNotInZone | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.14 | Unsigned32 | read-only | Number of server not in the zone errors. |
| U32 hpicfIpSlaMsgNameNotInZone | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.15 | Unsigned32 | read-only | Number of name not in the zone errors. |
| U32 hpicfIpSlaMsgDHCPFaildResln | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.16 | Unsigned32 | read-only | Number of DHCP failed resolutions. |
| U32 hpicfIpSlaMsgOffrNotRecvd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.17 | Unsigned32 | read-only | Number of DHCP offer not received errors. |
| U32 hpicfIpSlaMsgNACKRecvd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.18 | Unsigned32 | read-only | Number of NACKs received. |
| U32 hpicfIpSlaMsgThrHitRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.19 | Unsigned32 | read-only | Number of round-trip time hits to threshold. |
| U32 hpicfIpSlaMsgStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.20 | Unsigned32 | read-only | IP SLA current running status. |
| U32 hpicfIpSlaMsgNxtSched | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.21 | Unsigned32 | read-only | Next scheduled time of IP SLA probe. |
| U32 hpicfIpSlaMsgThrHitPostvSDAvg | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.22 | Unsigned32 | read-only | The average positive jitter value of packets moving from source to destination that cross the threshold. |
| U32 hpicfIpSlaMsgThrHitPostvDSAvg | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.23 | Unsigned32 | read-only | The average positive jitter value of packets moving from destination to source that cross the threshold. |
| U32 hpicfIpSlaMsgThrHitOneWayDSAvg | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.24 | Unsigned32 | read-only | The average time taken by packets moving from destination to source that cross the threshold. |
| U32 hpicfIpSlaMsgThrHitOneWaySDAvg | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.25 | Unsigned32 | read-only | The average time taken by packets moving from source to destination that cross the threshold. |
| U32 hpicfIpSlaMsgThrHitAvgICPIF | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.26 | Unsigned32 | read-only | Average value of the ICPIF of packets that cross the threshold. |
| U32 hpicfIpSlaMsgThrHitAvgMOS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.27 | Unsigned32 | read-only | Average value of the MOS of packets that cross the threshold. The Value of this object is 100 times of the actual value. |
| U32 hpicfIpSlaMsgNameServUnreach | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.28 | Unsigned32 | read-only | Number of errors due to name server being unreachable. |
| U32 hpicfIpSlaMsgDHCPReleaseErr | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.29 | Unsigned32 | read-only | Number of DHCP release errors. |
| U32 hpicfIpSlaMsgThrHitPktLoss | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.30 | Unsigned32 | read-only | Number of packet loss for each probe. |
| U32 hpicfIpSlaMsgDstUnreach | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.31 | Unsigned32 | read-only | Number of probes failed due to destination not being reachable. |
| U32 hpicfIpSlaMsgProbeSkpd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.32 | Unsigned32 | read-only | Number of probes skipped due to DNS resolution delay. |
| U32 hpicfIpSlaMsgDNSResolnFailed | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.33 | Unsigned32 | read-only | Number of times DNS resolution failed. |
| U32 hpicfIpSlaMsgNoRoutetoTgt | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.34 | Unsigned32 | read-only | Number of errors due to no route to target. |
| U32 hpicfIpSlaMsgUnbleToConctHost | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.35 | Unsigned32 | read-only | Number of errors due to no host connectivity. |
| U32 hpicfIpSlaMsgSuccConnection | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.36 | Unsigned32 | read-only | Number of successful connections. |
| U32 hpicfIpSlaMsgPossTrailDropped | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.37 | Unsigned32 | read-only | Number of probes dropped due to resource unavailability. |
| U32 hpicfIpSlaMsgNoRespFrmTgt | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.38 | Unsigned32 | read-only | Number of errors due to no response from target. |
| U32 hpicfIpSlaMsgProbeRespRecvd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.5.1.39 | Unsigned32 | read-only | Number of probes received. |
| hpicfIpSlaHistTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6 | not-accessible | This table specifies the history of IP SLA result. | |
| hpicfIpSlaHistEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1 | not-accessible | An entry on this table specifies the minimum, maximum and the average time taken from source to destination and vice versa. | |
| U32 hpicfIpSlaHistMinRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.1 | Unsigned32 | read-only | The minimum probe round-trip time. |
| U32 hpicfIpSlaHistMaxRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.2 | Unsigned32 | read-only | The maximum probe round-trip time. |
| U32 hpicfIpSlaHistAvgRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.3 | Unsigned32 | read-only | The average probe round-trip time. |
| U32 hpicfIpSlaHistTotalRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.4 | Unsigned32 | read-only | The total probe round-trip time. |
| U32 hpicfIpSlaHistRTT2 | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.5 | Unsigned32 | read-only | The sum of the squares of round-trip time. |
| U32 hpicfIpSlaHistNumOfRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.6 | Unsigned32 | read-only | The number of RTTs that are successfully measured. |
| U32 hpicfIpSlaHistProbID | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.7 | Unsigned32 | read-only | Probe ID number. |
| U32 hpicfIpSlaHistLastSuccProbTime | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.8 | Unsigned32 | read-only | Last success probe time. |
| U32 hpicfIpSlaHistPacketLoss | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.9 | Unsigned32 | read-only | The packet loss value during the jitter test. |
| U32 hpicfIpSlaHistSentPktNum | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.10 | Unsigned32 | read-only | Number of packets sent to responder. |
| U32 hpicfIpSlaHistRecvdPktNum | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.11 | Unsigned32 | read-only | Number of packets received from responder. |
| U32 hpicfIpSlaHistMinStoDPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.12 | Unsigned32 | read-only | The minimal positive jitter value recorded from source to destination. |
| U32 hpicfIpSlaHistMaxStoDPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.13 | Unsigned32 | read-only | The maximum positive jitter value recorded from source to destination. |
| U32 hpicfIpSlaHistNumOfPosSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.14 | Unsigned32 | read-only | Number of times the source to destination jitter has a positive value. |
| U32 hpicfIpSlaHistSumOfPosSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.15 | Unsigned32 | read-only | The sum of positive jitter values recorded from source to destination. |
| U32 hpicfIpSlaHistAvgStoDPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.16 | Unsigned32 | read-only | The average positive jitter value recorded from source to destination. |
| U32 hpicfIpSlaHistSum2PositivesSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.17 | Unsigned32 | read-only | The sum of square of positive jitter values recorded from source to destination. |
| U32 hpicfIpSlaHistMinDtoSPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.18 | Unsigned32 | read-only | The minimal positive jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistMaxDtoSPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.19 | Unsigned32 | read-only | The maximum positive jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistNumOfPosDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.20 | Unsigned32 | read-only | The positive jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistSumOfPosDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.21 | Unsigned32 | read-only | The sum of positive jitter values recorded from destination to source. |
| U32 hpicfIpSlaHistAvgDtoSPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.22 | Unsigned32 | read-only | The average positive jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistSum2PositivesDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.23 | Unsigned32 | read-only | The sum of square of positive jitter values recorded from destination-to-source. |
| U32 hpicfIpSlaHistMinStoDNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.24 | Unsigned32 | read-only | The minimal negative jitter value recorded from source to destination. |
| U32 hpicfIpSlaHistMaxStoDNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.25 | Unsigned32 | read-only | The maximum negative jitter value recorded from source to destination. |
| U32 hpicfIpSlaHistNumOfNegSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.26 | Unsigned32 | read-only | The number of negative jitter values recorded from source to destination. |
| U32 hpicfIpSlaHistSumOfNegSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.27 | Unsigned32 | read-only | The sum of negative jitter values recorded from source to destination. |
| U32 hpicfIpSlaHistAvgStoDNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.28 | Unsigned32 | read-only | The average negative jitter value recorded from source to destination. |
| U32 hpicfIpSlaHistSum2NegativesSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.29 | Unsigned32 | read-only | The sum of square of negative jitter values recorded from source to destination. |
| U32 hpicfIpSlaHistMinDtoSNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.30 | Unsigned32 | read-only | The minimal negative jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistMaxDtoSNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.31 | Unsigned32 | read-only | The maximum negative jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistNumOfNegDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.32 | Unsigned32 | read-only | The number of negative jitter values recorded from destination to source. |
| U32 hpicfIpSlaHistSumOfNegDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.33 | Unsigned32 | read-only | The negative jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistAvgDtoSNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.34 | Unsigned32 | read-only | The average negative jitter value recorded from destination to source. |
| U32 hpicfIpSlaHistSum2NegativesDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.35 | Unsigned32 | read-only | The negative jitter value recorded from source to destination. |
| U32 hpicfIpSlaHistMinStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.36 | Unsigned32 | read-only | The minimum delay recorded from source to destination. |
| U32 hpicfIpSlaHistMaxStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.37 | Unsigned32 | read-only | The maximum delay recorded from source to destination. |
| U32 hpicfIpSlaHistSumStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.38 | Unsigned32 | read-only | The sum of all delays recorded from source to destination. |
| U32 hpicfIpSlaHistNumOfDelaySD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.39 | Unsigned32 | read-only | The number of delays from source to destination that are successfully measured. |
| U32 hpicfIpSlaHistSum2DelaySD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.40 | Unsigned32 | read-only | The sum of squares of all delays recorded from source to destination. |
| U32 hpicfIpSlaHistMinDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.41 | Unsigned32 | read-only | The minimum delay recorded from destination to source. |
| U32 hpicfIpSlaHistMaxDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.42 | Unsigned32 | read-only | The maximum delay recorded from destination to source. |
| U32 hpicfIpSlaHistNumOfDelayDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.43 | Unsigned32 | read-only | The number of delays from destination to source that are successfully measured. |
| U32 hpicfIpSlaHistSumDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.44 | Unsigned32 | read-only | The sum of all delays recorded from destination to source. |
| U32 hpicfIpSlaHistSum2DelayDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.45 | Unsigned32 | read-only | The sum of squares of all delays recorded from destination to source. |
| U32 hpicfIpSlaHistICPIF | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.46 | Unsigned32 | read-only | The Calculated Planning Impairment Factor (ICPIF) value for the type-specified test. |
| U32 hpicfIpSlaHistMOS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.47 | Unsigned32 | read-only | The Mean Opinion Score (MOS) value for the type-specified test. The Value of this object is 100 times of the actual value. |
| U32 hpicfIpSlaHistAvgStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.48 | Unsigned32 | read-only | The average one-way time from source to destination. |
| U32 hpicfIpSlaHistAvgDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.6.1.49 | Unsigned32 | read-only | The average one-way time from destination to source. |
| hpicfIpSlaHistSummTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7 | not-accessible | This table specifies the history summary of IP SLA result. | |
| hpicfIpSlaHistSummEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1 | not-accessible | An entry on this table specifies the minimum, maximum and the average time taken from source to destination and vice versa. | |
| I32 hpicfIpSlaHistSummIndx | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.1 | Integer32 | not-accessible | This is an index for history summary. Its value can vary from 1 to 50. |
| U32 hpicfIpSlaHistSummStartTime | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.2 | Unsigned32 | read-only | Time at which the type-specified test was executed. |
| U32 hpicfIpSlaHistSummStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.3 | Unsigned32 | read-only | The status of the IP SLA test. |
| U32 hpicfIpSlaHistSummRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.4 | Unsigned32 | read-only | The round-trip time for a successfully measured test. |
| U32 hpicfIpSlaHistSummResolvdIP | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.5 | Unsigned32 | read-only | Resolved IP address. |
| U32 hpicfIpSlaHistSummDescription | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.6 | Unsigned32 | read-only | Error description. |
| U32 hpicfIpSlaHistSummStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.7 | Unsigned32 | read-only | Source to destination delay. |
| U32 hpicfIpSlaHistSummDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.7.1.8 | Unsigned32 | read-only | Destination to source delay. |
| hpicfIpSlaHistAggrTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8 | not-accessible | This table specifies the aggregate value of IP SLA result. The average value is calculating on last 25 probes. Or the calculation will do on the number of probes if the probe count is less than 25 | |
| hpicfIpSlaHistAggrEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1 | not-accessible | An entry on this table specifies aggregate value of minimum, maximum and the average time taken from source to destination and vice versa. | |
| U32 hpicfIpSlaHistAggrMinRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.1 | Unsigned32 | read-only | The minimum round-trip time for the last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.2 | Unsigned32 | read-only | The maximum round-trip time for the last 25 probes. |
| U32 hpicfIpSlaHistAggrNumOfRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.3 | Unsigned32 | read-only | The number of RTTs that are successfully measured for last 25 probes. |
| U32 hpicfIpSlaHistAggrAvgRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.4 | Unsigned32 | read-only | The average round-trip time of last 25 probes. |
| U32 hpicfIpSlaHistAggrTotalRTT | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.5 | Unsigned32 | read-only | The total round-trip time of last 25 probes. |
| U32 hpicfIpSlaHistAggrRTT2 | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.6 | Unsigned32 | read-only | The average of the sum of squares of RTTs for the last 25 probes. |
| U32 hpicfIpSlaHistAggrFrstProbStTime | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.7 | Unsigned32 | read-only | First probe start time. |
| U32 hpicfIpSlaHistAggrProbFailReason | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.8 | Unsigned32 | read-only | Probe failure reason. |
| U32 hpicfIpSlaHistAggrPacketLoss | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.9 | Unsigned32 | read-only | The percentage of packet loss in last 25 probes. |
| U32 hpicfIpSlaHistAggrSentPktNum | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.10 | Unsigned32 | read-only | The total number of packets sent. |
| U32 hpicfIpSlaHistAggrRecvdPktNum | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.11 | Unsigned32 | read-only | The total number of packets received. |
| U32 hpicfIpSlaHistAggrMinStoDPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.12 | Unsigned32 | read-only | The minimum positive jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxStoDPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.13 | Unsigned32 | read-only | The maximum positive jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrNumOfPosSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.14 | Unsigned32 | read-only | The number of times source to destination jitter value became positive. |
| U32 hpicfIpSlaHistAggrSumOfPosSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.15 | Unsigned32 | read-only | The average of the sum of positive jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrAvgStoDPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.16 | Unsigned32 | read-only | The average of the positive jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrSum2PostvSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.17 | Unsigned32 | read-only | The aggregate of square sum of positive jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrMinDtoSPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.18 | Unsigned32 | read-only | The minimum positive jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxDtoSPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.19 | Unsigned32 | read-only | The maximum positive jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrNumOfPosDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.20 | Unsigned32 | read-only | The number of times destination to source jitter was positive. |
| U32 hpicfIpSlaHistAggrSumOfPosDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.21 | Unsigned32 | read-only | The sum of positive jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrAvgDtoSPostv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.22 | Unsigned32 | read-only | The sum of average positive jitter values from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrSum2PostvDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.23 | Unsigned32 | read-only | The aggregate of square sum of positive jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrMinStoDNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.24 | Unsigned32 | read-only | The minimum negative jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxStoDNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.25 | Unsigned32 | read-only | The maximum negative jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrNumOfNegSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.26 | Unsigned32 | read-only | The number of times jitter value from source to destination became negative. |
| U32 hpicfIpSlaHistAggrSumOfNegSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.27 | Unsigned32 | read-only | The sum of negative jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrAvgStoDNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.28 | Unsigned32 | read-only | The average of the negative jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrSum2NegtvSD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.29 | Unsigned32 | read-only | The aggregate of square sum of negative jitter value from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrMinDtoSNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.30 | Unsigned32 | read-only | The minimum negative jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxDtoSNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.31 | Unsigned32 | read-only | The maximum negative jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrNumOfNegDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.32 | Unsigned32 | read-only | The number of times jitter value from destination to source became negative. |
| U32 hpicfIpSlaHistAggrSumOfNegDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.33 | Unsigned32 | read-only | The sum of negative jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrAvgDtoSNegtv | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.34 | Unsigned32 | read-only | The average of the negative jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrSum2NegtvDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.35 | Unsigned32 | read-only | The aggregate of square sum of negative jitter value from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrMinStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.36 | Unsigned32 | read-only | The minimum one-way time from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.37 | Unsigned32 | read-only | The maximum one-way time from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrSumStoDDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.38 | Unsigned32 | read-only | The sum of one-way time from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrNumOfDelaySD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.39 | Unsigned32 | read-only | The number of times source to destination delay occurred for the last 25 probes. |
| U32 hpicfIpSlaHistAggrSum2DelaySD | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.40 | Unsigned32 | read-only | The sum of squares of one-way delay from source to destination for last 25 probes. |
| U32 hpicfIpSlaHistAggrMinDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.41 | Unsigned32 | read-only | The minimum one-way delay from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.42 | Unsigned32 | read-only | The maximum one-way delay from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrNumOfDelayDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.43 | Unsigned32 | read-only | The number of times destination to source delay occurred for the last 25 probes. |
| U32 hpicfIpSlaHistAggrSumDtoSDelay | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.44 | Unsigned32 | read-only | The sum of one-way delay from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrSum2DelayDS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.45 | Unsigned32 | read-only | The sum of squares of one-way delay from destination to source for last 25 probes. |
| U32 hpicfIpSlaHistAggrMinICPIF | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.46 | Unsigned32 | read-only | The minimum ICPIF value for last 25 probes. |
| U32 hpicfIpSlaHistAggrMaxICPIF | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.47 | Unsigned32 | read-only | The maximum ICPIF value for last 25 probes. |
| U32 hpicfIpSlaHistAggrMinMOS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.48 | Unsigned32 | read-only | The minimum MOS value for last 25 probes. The Value of this object is 100 times of the actual value. |
| U32 hpicfIpSlaHistAggrMaxMOS | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.8.1.49 | Unsigned32 | read-only | The maximum MOS value for last 25 probes. The Value of this object is 100 times of the actual value. |
| hpicfIpSlaRespResultTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.9 | not-accessible | This table specifies the IP SLA responder result parameters as entries. | |
| hpicfIpSlaRespResultEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.9.1 | not-accessible | An entry on this table specifies responder status and number of packets received and responded. | |
| U32 hpicfIpSlaRespStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.9.1.1 | Unsigned32 | read-only | The status of the responder. |
| U32 hpicfIpSlaRespnumPktRcvd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.9.1.2 | Unsigned32 | read-only | The number of packets received by the responder. |
| U32 hpicfIpSlaRespNumPktRespnd | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.9.1.3 | Unsigned32 | read-only | The number of packets sent by the responder. |
| hpicfIpSlaJitterRespTable | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10 | not-accessible | This table specifies IP SLA jitter responder parameters as entries. | |
| hpicfIpSlaJitterRespEntry | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1 | not-accessible | An entry on this table specifies the local IP address, port number and row status corresponding to each SLA responder config. | |
| INT hpicfIpSlaJitterRespType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1.1 | INTEGER | not-accessible | The SLA jitter responder type. The udpJitter and udpJitterVoIP values calculate one-way delay, therefore a timestamp has to be embedded while replying back. This is one of the indexes for hpicfIpSlaJitterRespTable. |
| IPt hpicfIpSlaJitterRespAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1.2 | InetAddressType | read-create | SLA jitter responder IP address type. |
| IP hpicfIpSlaJitterRespAddress | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1.3 | InetAddress | not-accessible | The local IP address to which the responder is bound. This is one of the indexes for hpicfIpSlaJitterRespTable. |
| INE hpicfIpSlaJitterRespL4Port | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1.4 | InetPortNumber | not-accessible | L4 port number on hpicfIpSlaJitterRespAddress where the responder listens for probe packets from SLA source. This is one of the indexes for hpicfIpSlaJitterRespTable. The allowed range is 1024 to 65535. |
| IPt hpicfIpSlaJitterRespSrcAddrType | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1.5 | InetAddressType | read-create | SLA jitter responder source IP address type. |
| IP hpicfIpSlaJitterRespSrcAddress | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1.6 | InetAddress | not-accessible | The source IP address to which the responder is responding. |
| ROW hpicfIpSlaJitterRespRowStatus | 1.3.6.1.4.1.11.2.14.11.5.1.127.1.10.1.7 | RowStatus | read-create | SLA jitter responder row status. |
| hpicfIpSlaConformance | 1.3.6.1.4.1.11.2.14.11.5.1.127.2 | |||
| hpicfIpSlaGroups | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1 | |||
| hpicfIpSlaGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.1 | A mandatory group with a set of IP SLA objects. | ||
| hpicfIpSlaAttrGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.2 | A group with a set of IP SLA attribute objects. | ||
| hpicfIpSlaThrGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.3 | A group with a set of IP SLA threshold objects. | ||
| hpicfIpSlaRespGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.4 | A group with a set of IP SLA responder objects. | ||
| hpicfIpSlaNotificationsGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.5 | A collection of IP SLA source and responder notifications objects. | ||
| hpicfIpSlaMsgGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.6 | A mandatory group with a set of IP SLA result objects. | ||
| hpicfIpSlaHistGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.7 | A mandatory group with a set of IP SLA history objects. | ||
| hpicfIpSlaHistSummGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.8 | A mandatory group with a set of IP SLA history summary objects. | ||
| hpicfIpSlaAttrGroup1 | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.9 | A group with a set of IP SLA attribute objects. | ||
| hpicfIpSlaHistAggrGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.10 | A mandatory group with a set of IP SLA aggregate result summary objects. | ||
| hpicfIpSlaRespResultGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.11 | A mandatory group with a set of IP SLA responder objects. | ||
| hpicfIpSlaJitterRespGroup | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.12 | A group with a set of IP SLA jitter responder objects. | ||
| hpicfIpSlaCompliances | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.2 | |||
| hpicfIpSlaCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.2.1 | The compliance statement for HP switches that support IP SLA. | ||
| hpicfIpSlaCompliance1 | 1.3.6.1.4.1.11.2.14.11.5.1.127.2.2.2 | The compliance statement for HP switches that support IP SLA. |
RFC description
HP/Aruba vendor-private MIB for IP Service Level Agreement (SLA) monitoring and measurement on ICF switches.
Start monitoring HP ProCurve/Aruba managed switch/router (IP SLA performance probes) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.