BKTEL-HFC862-NECE-MIB

All MIBs › BKTEL-HFC862-NECE-MIB

Category: DOCSIS and Cable, Vendor: BKTEL

Description: Manages network element control and element (NECE) parameters for BKTEL HFC-862 optical cable nodes.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BKTEL-HFC862-NECE-MIB?

BKTEL-HFC862-NECE-MIB is a vendor-specific MIB from BKtel Communications for the HFC-862 family of hybrid fiber-coax (HFC) optical network element cards used in cable television and broadband access networks. It exposes network element control (NECE) parameters covering configuration, operational mode, and status registers for the optical node/transponder hardware. Because BKtel HFC nodes are unmanned outside-plant devices, this MIB is central to monitoring hardware health, such as module presence, alarm/fault state, and operational versus administrative status of the optical transmit/receive components, so operators can detect a failed node before it causes a service outage. It is typically layered on top of a vendor enterprise MIB tree and used alongside standard IF-MIB/ENTITY-MIB objects for interface and inventory context rather than replacing them. Deployment context is HFC headend and outside-plant optical node management by cable/MSO network operations teams using NMS platforms that poll BKtel nodes for status and configuration changes. Engineers can download the BKTEL-HFC862-NECE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BKTEL-HFC862-NECE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

BKtel HFC-862 optical network element / cable node

Monitoring Examples

Since no object list is available for this module, a typical use would poll NECE status registers on the HFC-862 optical node table for operational state and alarm flags, alerting when a node transitions from normal to fault. An admin would also check configuration objects for optical transmit power or node addressing to confirm a newly provisioned node matches the headend's plan. A sudden alarm-flag change combined with loss of an expected NECE entry would indicate a node has dropped off the HFC segment.

What Can Be Monitored

network element operational status
alarm/fault conditions
node configuration state
optical node addressing
administrative vs operational status

Imported Objects

From BKTEL-HFC862-BASE-MIB

DisplayString
ModuleWidthValue
NESlotValue
PerceivedSeverityValue
TruthValue
modules	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks
enterprises
experimental

OIDs

OID symbolic	OID numeric	Type	Access	Description
nece	1.3.6.1.4.1.7501.1.2.100
neceCommon	1.3.6.1.4.1.7501.1.2.100.1
STR neceCommonDescr	1.3.6.1.4.1.7501.1.2.100.1.2.1.3	DisplayString	read-write	Module alias name
neceCommonEntry	1.3.6.1.4.1.7501.1.2.100.1.2.1		not-accessible	Common-Values for a module.
STR neceCommonFirmwareId	1.3.6.1.4.1.7501.1.2.100.1.2.1.4	DisplayString	read-only	Module firmware version
MOD neceCommonModuleWidth	1.3.6.1.4.1.7501.1.2.100.1.2.1.5	ModuleWidthValue	read-only	The width of the module.
INT neceCommonNumberOfModules	1.3.6.1.4.1.7501.1.2.100.1.1	INTEGER	read-only	Number of modules in table.
neceCommonTable	1.3.6.1.4.1.7501.1.2.100.1.2		not-accessible	The table contains all modules of the nece-type in the NE
STR neceCommonType	1.3.6.1.4.1.7501.1.2.100.1.2.1.2	DisplayString	read-only	Module model name
T/F neceConfigCableWatchUsed	1.3.6.1.4.1.7501.1.2.100.3.1.1.65	TruthValue	read-write	This parameter is obsolete and no more needed, always returns false(2)
STR neceConfigDaylightSavingFrom	1.3.6.1.4.1.7501.1.2.100.3.1.1.72	DisplayString	read-write	Daylight saving start time in a special textformat (see manual for detail)
STR neceConfigDaylightSavingTo	1.3.6.1.4.1.7501.1.2.100.3.1.1.73	DisplayString	read-write	Daylight saving end time in a special textformat (see manual for detail)
IP neceConfigDefaultrouter	1.3.6.1.4.1.7501.1.2.100.3.1.1.52	IpAddress	read-write	The default router of the NEC. NOTE: The NECE executes a reset if this parameter gets changed
OCT neceConfigFactoryCommandLine	1.3.6.1.4.1.7501.1.2.100.3.1.1.71	OCTET STRING	read-write	A factory internal command interface
STR neceConfigGetCommunity	1.3.6.1.4.1.7501.1.2.100.3.1.1.59	DisplayString	read-write	The community name that is allowed for GET requests NOTES: - By writing 'neceConfigGetCommunity' AND 'neceConfigSetCommunity' to an empty string of size 0, the default community settings are used.
STR neceConfigGpio10Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.40	DisplayString	read-write	A description for the general purpose port no. 10
GPI neceConfigGpio10LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.39	GpioLogicLevel	read-write	The logic level of the general purpose port no. 10
GPI neceConfigGpio10Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.38	GpioMode	read-write	The mode of the general purpose port no. 10
GPI neceConfigGpio10Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.37	GpioType	read-only	The type of the general purpose port no. 10
STR neceConfigGpio11Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.44	DisplayString	read-write	A description for the general purpose port no. 11
GPI neceConfigGpio11LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.43	GpioLogicLevel	read-write	The logic level of the general purpose port no. 11
GPI neceConfigGpio11Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.42	GpioMode	read-write	The mode of the general purpose port no. 11
GPI neceConfigGpio11Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.41	GpioType	read-only	The type of the general purpose port no. 11
STR neceConfigGpio12Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.48	DisplayString	read-write	A description for the general purpose port no. 12
GPI neceConfigGpio12LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.47	GpioLogicLevel	read-write	The logic level of the general purpose port no. 12
GPI neceConfigGpio12Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.46	GpioMode	read-write	The mode of the general purpose port no. 12
GPI neceConfigGpio12Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.45	GpioType	read-only	The type of the general purpose port no. 12
STR neceConfigGpio1Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.4	DisplayString	read-write	A description for the general purpose port no. 1
GPI neceConfigGpio1LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.3	GpioLogicLevel	read-write	The logic level of the general purpose port no. 1
GPI neceConfigGpio1Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.2	GpioMode	read-write	The mode of the general purpose port no. 1
GPI neceConfigGpio1Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.1	GpioType	read-only	The type of the general purpose port no. 1
STR neceConfigGpio2Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.8	DisplayString	read-write	A description for the general purpose port no. 2
GPI neceConfigGpio2LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.7	GpioLogicLevel	read-write	The logic level of the general purpose port no. 2
GPI neceConfigGpio2Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.6	GpioMode	read-write	The mode of the general purpose port no. 2
GPI neceConfigGpio2Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.5	GpioType	read-only	The type of the general purpose port no. 2
STR neceConfigGpio3Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.12	DisplayString	read-write	A description for the general purpose port no. 3
GPI neceConfigGpio3LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.11	GpioLogicLevel	read-write	The logic level of the general purpose port no. 3
GPI neceConfigGpio3Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.10	GpioMode	read-write	The mode of the general purpose port no. 3
GPI neceConfigGpio3Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.9	GpioType	read-only	The type of the general purpose port no. 3
STR neceConfigGpio4Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.16	DisplayString	read-write	A description for the general purpose port no. 4
GPI neceConfigGpio4LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.15	GpioLogicLevel	read-write	The logic level of the general purpose port no. 4
GPI neceConfigGpio4Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.14	GpioMode	read-write	The mode of the general purpose port no. 4
GPI neceConfigGpio4Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.13	GpioType	read-only	The type of the general purpose port no. 4
STR neceConfigGpio5Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.20	DisplayString	read-write	A description for the general purpose port no. 5
GPI neceConfigGpio5LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.19	GpioLogicLevel	read-write	The logic level of the general purpose port no. 5
GPI neceConfigGpio5Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.18	GpioMode	read-write	The mode of the general purpose port no. 5
GPI neceConfigGpio5Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.17	GpioType	read-only	The type of the general purpose port no. 5
STR neceConfigGpio6Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.24	DisplayString	read-write	A description for the general purpose port no. 6
GPI neceConfigGpio6LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.23	GpioLogicLevel	read-write	The logic level of the general purpose port no. 6
GPI neceConfigGpio6Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.22	GpioMode	read-write	The mode of the general purpose port no. 6
GPI neceConfigGpio6Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.21	GpioType	read-only	The type of the general purpose port no. 6
STR neceConfigGpio7Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.28	DisplayString	read-write	A description for the general purpose port no. 7
GPI neceConfigGpio7LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.27	GpioLogicLevel	read-write	The logic level of the general purpose port no. 7
GPI neceConfigGpio7Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.26	GpioMode	read-write	The mode of the general purpose port no. 7
GPI neceConfigGpio7Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.25	GpioType	read-only	The type of the general purpose port no. 7
STR neceConfigGpio8Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.32	DisplayString	read-write	A description for the general purpose port no. 8
GPI neceConfigGpio8LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.31	GpioLogicLevel	read-write	The logic level of the general purpose port no. 8
GPI neceConfigGpio8Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.30	GpioMode	read-write	The mode of the general purpose port no. 8
GPI neceConfigGpio8Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.29	GpioType	read-only	The type of the general purpose port no. 8
STR neceConfigGpio9Description	1.3.6.1.4.1.7501.1.2.100.3.1.1.36	DisplayString	read-write	A description for the general purpose port no. 9
GPI neceConfigGpio9LogicLevel	1.3.6.1.4.1.7501.1.2.100.3.1.1.35	GpioLogicLevel	read-write	The logic level of the general purpose port no. 9
GPI neceConfigGpio9Mode	1.3.6.1.4.1.7501.1.2.100.3.1.1.34	GpioMode	read-write	The mode of the general purpose port no. 9
GPI neceConfigGpio9Type	1.3.6.1.4.1.7501.1.2.100.3.1.1.33	GpioType	read-only	The type of the general purpose port no. 9
HFC neceConfigHfcInventoryFormat	1.3.6.1.4.1.7501.1.2.100.3.1.1.68	HfcInventoryFormatValue	read-only	Selects the supported format of the hfcInventoryFabricData (T-NOVA-HFC-INVENTORY-MIB)
T/F neceConfigHmsNotificationsEnable	1.3.6.1.4.1.7501.1.2.100.3.1.1.67	TruthValue	read-write	With this control the user can disable all traps of type NOTIFY and there entries in the SCTE HMS tree. NOTE: The NECE executes a reset if this parameter gets changed
HMS neceConfigHmsTrapsCompliance	1.3.6.1.4.1.7501.1.2.100.3.1.1.66	HmsTrapsComplianceValue	read-write	Set the compliance mode of the SCTE HMS traps In earlier versions of NECE (<= Sw.Rel. 1.10) the trap compliance to the SCTE HMS MIBs was not fully given. See manual for details.
IP neceConfigIpAddress	1.3.6.1.4.1.7501.1.2.100.3.1.1.50	IpAddress	read-write	The ip address of the NEC. NOTE: The NECE executes a reset if this parameter gets changed
NES neceConfigNESlotWrite	1.3.6.1.4.1.7501.1.2.100.3.1.1.49	NESlotWriteValue	read-write	By writing this variable a slot can be assigned for devices that dont support hardware slot detection. Reading '-1' means that the slot position is NOT writable.
IP neceConfigNetmask	1.3.6.1.4.1.7501.1.2.100.3.1.1.51	IpAddress	read-write	The netmask of the NEC. NOTE: The NECE executes a reset if this parameter gets changed
IP neceConfigNtpServerIp	1.3.6.1.4.1.7501.1.2.100.3.1.1.70	IpAddress	read-write	The ip address of an NTP time server. Setting the ip to 0.0.0.0 disables the time server lookup. NOTE: Not all NECE's support an NTP server.
STR neceConfigSetCommunity	1.3.6.1.4.1.7501.1.2.100.3.1.1.60	DisplayString	read-write	The community name that is allowed for SET and GET requests NOTES: - By writing 'neceConfigGetCommunity' AND 'neceConfigSetCommunity' to an empty string of size 0, the default community settings are used.
INT neceConfigTimezone	1.3.6.1.4.1.7501.1.2.100.3.1.1.69	INTEGER	read-write	The timezone in units of half hours from GMT (Greenwich Mean Time). For example: Berlin => +2 half hours means GMT+1 hour Tokio => +18 half hours means GMT+9 hours NewYork => -10 half hours means GMT-5 hours NOTE: Not all NECE's support an NTP server.
TRA neceConfigTrapAccumulationTime	1.3.6.1.4.1.7501.1.2.100.3.1.1.64	TrapAccumulationTimeValue	read-write	Time in seconds that the NECE waits before sending all pending traps. NOTE: There are two condition where the NECE sends its pending traps earlier ignoring this accumulation time (of course verifying first): 1) The NECE's internal trap buffer is 3/4 full 2) The NECE's SNMP agent is polled by a request from manager !!! Only valid if neceConfigTrapReceiverVerify == true(1) !!!
STR neceConfigTrapReceiver1Community	1.3.6.1.4.1.7501.1.2.100.3.1.1.54	DisplayString	read-write	The community name used for traps to host no.1
IP neceConfigTrapReceiver1HostIp	1.3.6.1.4.1.7501.1.2.100.3.1.1.53	IpAddress	read-write	The ip address of the host no.1 that should receive traps Address 0.0.0.0 disables the trap. Broad- or multicast addresses are not allowed
IP neceConfigTrapReceiver2HostIp	1.3.6.1.4.1.7501.1.2.100.3.1.1.55	IpAddress	read-write	The ip address of the host no.2 that should receive traps Address 0.0.0.0 disables the trap. Broad- or multicast addresses are not allowed
STR neceConfigTrapReceiver2to4Community	1.3.6.1.4.1.7501.1.2.100.3.1.1.56	DisplayString	read-write	The community name used for traps to hosts no.2 to no.4
IP neceConfigTrapReceiver3HostIp	1.3.6.1.4.1.7501.1.2.100.3.1.1.57	IpAddress	read-write	The ip address of the host no.3 that should receive traps Address 0.0.0.0 disables the trap. Broad- or multicast addresses are not allowed NOTE: The community name 'neceConfigTrapReceiver2to4Community' is used for this trap receiver no. 3
IP neceConfigTrapReceiver4HostIp	1.3.6.1.4.1.7501.1.2.100.3.1.1.58	IpAddress	read-write	The ip address of the host no.4 that should receive traps Address 0.0.0.0 disables the trap. Broad- or multicast addresses are not allowed NOTE: The community name 'neceConfigTrapReceiver2to4Community' is used for this trap receiver no. 4
T/F neceConfigTrapReceiverVerify	1.3.6.1.4.1.7501.1.2.100.3.1.1.61	TruthValue	read-write	If TRUE, the NECE verifies if the 'sysDescr' variable is readable on host with ip-address 'neceConfigTrapVerifyReceiverIp' before sending new traps. NOTE: The NECE executes a reset if this parameter gets changed
IP neceConfigTrapVerifyReceiverIp	1.3.6.1.4.1.7501.1.2.100.3.1.1.62	IpAddress	read-write	The ip address of the host that should receive the 'sysDescr' verify request. Broad- or multicast addresses are not allowed. !!! Only valid if neceConfigTrapReceiverVerify == true(1) !!!
TRA neceConfigTrapVerifyTimeout	1.3.6.1.4.1.7501.1.2.100.3.1.1.63	TrapVerifyTimeoutValue	read-write	Timeout in seconds after which the NECE stops trying to verify 'sysDescr'. All pending traps are sent, although no verify response, after that timeout. !!! Only valid if neceConfigTrapReceiverVerify == true(1) !!!
neceConfiguration	1.3.6.1.4.1.7501.1.2.100.3
neceConfigurationEntry	1.3.6.1.4.1.7501.1.2.100.3.1.1		not-accessible
neceConfigurationTable	1.3.6.1.4.1.7501.1.2.100.3.1		not-accessible
neceControl	1.3.6.1.4.1.7501.1.2.100.4
neceControlEntry	1.3.6.1.4.1.7501.1.2.100.4.1.1		not-accessible	Alarms for a module.
T/F neceControlReset	1.3.6.1.4.1.7501.1.2.100.4.1.1.1	TruthValue	read-write	Reset the module.
neceControlTable	1.3.6.1.4.1.7501.1.2.100.4.1		not-accessible
neceDisplay	1.3.6.1.4.1.7501.1.2.100.6
neceDisplayEntry	1.3.6.1.4.1.7501.1.2.100.6.1.1		not-accessible
neceDisplayTable	1.3.6.1.4.1.7501.1.2.100.6.1		not-accessible
INT neceDisplayTrapsDiscarded	1.3.6.1.4.1.7501.1.2.100.6.1.1.2	INTEGER	read-only	Number of traps that the NECE has discarded. Discarded traps occur because of trap buffer overflow or timeouts.
INT neceDisplayTrapsSent	1.3.6.1.4.1.7501.1.2.100.6.1.1.1	INTEGER	read-only	Number of traps that the NECE has sent.
neceMeasuringValues	1.3.6.1.4.1.7501.1.2.100.5
neceMeasuringValuesEntry	1.3.6.1.4.1.7501.1.2.100.5.1.1		not-accessible	Common-Values for a module.
neceMeasuringValuesTable	1.3.6.1.4.1.7501.1.2.100.5.1		not-accessible
NES neceNESlot	1.3.6.1.4.1.7501.1.2.100.1.2.1.1	NESlotValue	read-only	The virtual slotID
neceStates	1.3.6.1.4.1.7501.1.2.100.2
neceStatesEntry	1.3.6.1.4.1.7501.1.2.100.2.1.1		not-accessible	Alarms for a module.
PER neceStatesFanLeft	1.3.6.1.4.1.7501.1.2.100.2.1.1.15	PerceivedSeverityValue	read-only	The left (looking from front side) fan unit fails. Only valid for 2G6 Systems !! Non 2G6 Systems always report clear(5)
PER neceStatesFanRight	1.3.6.1.4.1.7501.1.2.100.2.1.1.16	PerceivedSeverityValue	read-only	The right (looking from front side) fan unit fails. Only valid for 2G6 Systems !! Non 2G6 Systems always report clear(5)
PER neceStatesGpInput1	1.3.6.1.4.1.7501.1.2.100.2.1.1.1	PerceivedSeverityValue	read-only	State of general purpose input no. 1.
PER neceStatesGpInput10	1.3.6.1.4.1.7501.1.2.100.2.1.1.10	PerceivedSeverityValue	read-only	State of general purpose input no. 10.
PER neceStatesGpInput11	1.3.6.1.4.1.7501.1.2.100.2.1.1.11	PerceivedSeverityValue	read-only	State of general purpose input no. 11.
PER neceStatesGpInput12	1.3.6.1.4.1.7501.1.2.100.2.1.1.12	PerceivedSeverityValue	read-only	State of general purpose input no. 12.
PER neceStatesGpInput2	1.3.6.1.4.1.7501.1.2.100.2.1.1.2	PerceivedSeverityValue	read-only	State of general purpose input no. 2.
PER neceStatesGpInput3	1.3.6.1.4.1.7501.1.2.100.2.1.1.3	PerceivedSeverityValue	read-only	State of general purpose input no. 3.
PER neceStatesGpInput4	1.3.6.1.4.1.7501.1.2.100.2.1.1.4	PerceivedSeverityValue	read-only	State of general purpose input no. 4.
PER neceStatesGpInput5	1.3.6.1.4.1.7501.1.2.100.2.1.1.5	PerceivedSeverityValue	read-only	State of general purpose input no. 5.
PER neceStatesGpInput6	1.3.6.1.4.1.7501.1.2.100.2.1.1.6	PerceivedSeverityValue	read-only	State of general purpose input no. 6.
PER neceStatesGpInput7	1.3.6.1.4.1.7501.1.2.100.2.1.1.7	PerceivedSeverityValue	read-only	State of general purpose input no. 7.
PER neceStatesGpInput8	1.3.6.1.4.1.7501.1.2.100.2.1.1.8	PerceivedSeverityValue	read-only	State of general purpose input no. 8.
PER neceStatesGpInput9	1.3.6.1.4.1.7501.1.2.100.2.1.1.9	PerceivedSeverityValue	read-only	State of general purpose input no. 9.
PER neceStatesPowerSupplyLeft	1.3.6.1.4.1.7501.1.2.100.2.1.1.13	PerceivedSeverityValue	read-only	The left (looking from front side) power supply unit fails. Only valid for 2G6 Systems !! Non 2G6 Systems always report clear(5)
PER neceStatesPowerSupplyRight	1.3.6.1.4.1.7501.1.2.100.2.1.1.14	PerceivedSeverityValue	read-only	The right (looking from front side) power supply unit fails. Only valid for 2G6 Systems !! Non 2G6 Systems always report clear(5)
neceStatesTable	1.3.6.1.4.1.7501.1.2.100.2.1		not-accessible
INT neceTemperatureHi	1.3.6.1.4.1.7501.1.2.100.5.1.1.4	INTEGER	read-only	Temperature high warning threshold in steps of 0,1�C.
INT neceTemperatureHiHi	1.3.6.1.4.1.7501.1.2.100.5.1.1.5	INTEGER	read-only	Temperature high alarm threshold in steps of 0,1�C.
INT neceTemperatureLo	1.3.6.1.4.1.7501.1.2.100.5.1.1.2	INTEGER	read-only	Temperature low warning threshold in steps of 0,1�C.
INT neceTemperatureLoLo	1.3.6.1.4.1.7501.1.2.100.5.1.1.1	INTEGER	read-only	Temperature low alarm threshold in steps of 0,1�C.
INT neceTemperatureValue	1.3.6.1.4.1.7501.1.2.100.5.1.1.3	INTEGER	read-only	Temperature in steps of 0,1�C.

RFC description

Manages NECE configuration including network element states, GPIO ports, alarms, and trap receivers.

Start monitoring BKtel optical network elements with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BKTEL-HFC862-NECE-MIB

What Is BKTEL-HFC862-NECE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description