All MIBs › BIANCA-BRICK-HDSL2SHDSL2-MIB
Category: DSL and Broadband, Vendor: bintec
Description: Manages HDSL2/SHDSL2 DSL interface line status, rate negotiation, and error counters on bintec BIANCA/BRICK.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is BIANCA-BRICK-HDSL2SHDSL2-MIB?
BIANCA-BRICK-HDSL2SHDSL2-MIB is a legacy BinTec/Bianca-Brick (later Funkwerk) proprietary MIB (enterprise OID 272) packaging the standard IETF HDSL2/SHDSL MIB (RFC 3276) for BinTec/Bianca-Brick routers. Its inventory table records vendor ID/model/serial number, EOC (Embedded Operations Channel) software version, standard version, list/issue number, vendor software version, equipment code, and transmission-mode capability, while an endpoint-configuration table records side (near/far), wire interface, min/max line rate, transmission mode, and worst-case target margin (up/down). As a configuration/hardware-status MIB it lets an administrator confirm an HDSL2/SHDSL line's negotiated rate and target-margin settings. It is deployed on legacy BinTec/Bianca-Brick routers with HDSL2/SHDSL interfaces. Engineers can download the BIANCA-BRICK-HDSL2SHDSL2-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in BIANCA-BRICK-HDSL2SHDSL2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Legacy BinTec/Bianca-Brick routers (HDSL2/SHDSL interfaces)
Monitoring Examples
An administrator checks hdsl2ShdslEndpointConfMinLineRate and MaxLineRate to confirm an HDSL2/SHDSL line's rate range matches the intended circuit provisioning on a Bianca-Brick router.
What Can Be Monitored
- HDSL2/SHDSL line rate and inventory identification
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| enterprises |
From RFC1158-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| bibo | 1.3.6.1.4.1.272.4 | |||
| bintec | 1.3.6.1.4.1.272 | |||
| hdsl2shdsl | 1.3.6.1.4.1.272.4.35 | |||
| INT hdsl2ShdslEndpointConfCapListStyle | 1.3.6.1.4.1.272.4.35.1.1.4.1.20 | INTEGER | read-write | This object specifies the data format of the capability list, that is exchanged during the G.994.1 handshake: auto - automatic detection of the used capability list style. old - only ATM modes till 2312 kbps can be negotiated. new - all modes can be negotiated. |
| hdsl2ShdslEndpointConfEntry | 1.3.6.1.4.1.272.4.35.1.1.4.1 | not-accessible | An entry in the hdsl2ShdslEndpointConfTable. Each entry represents a single segment endpoint in a HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line. | |
| INT hdsl2ShdslEndpointConfGroupId | 1.3.6.1.4.1.272.4.35.1.1.4.1.14 | INTEGER | read-write | This object defines which wire-pairs belong to the same M-pair group or IMA group. Members of the same group have the same entry. |
| INT hdsl2ShdslEndpointConfIfIndex | 1.3.6.1.4.1.272.4.35.1.1.4.1.1 | INTEGER | read-only | This object specifies the associated interface index of this HDSL2/SHDSL line. |
| INT hdsl2ShdslEndpointConfLicenseUsage | 1.3.6.1.4.1.272.4.35.1.1.4.1.16 | INTEGER | read-only | Shows which license type is currently used for this SHDSL interface. |
| INT hdsl2ShdslEndpointConfLineProbeEnable | 1.3.6.1.4.1.272.4.35.1.1.4.1.15 | INTEGER | read-write | This object specifies the configuration of the PMMS behavior: auto - Line Probe is enabled if hdsl2ShdslEndpointConfMinLineRate < hdsl2ShdslEndpointConfMaxLineRate. disable - Line Probe is disabled. enable - Line Probe is enabled. enable_std - Line Probe is enabled and standard compliant behaviour is enforced. |
| INT hdsl2ShdslEndpointConfMaxLineRate | 1.3.6.1.4.1.272.4.35.1.1.4.1.7 | INTEGER | read-write | This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. |
| INT hdsl2ShdslEndpointConfMinLineRate | 1.3.6.1.4.1.272.4.35.1.1.4.1.6 | INTEGER | read-write | This object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. |
| INT hdsl2ShdslEndpointConfMinWirePairs | 1.3.6.1.4.1.272.4.35.1.1.4.1.19 | INTEGER | read-write | This object configures the minimum number of wire pairs for the associated SHDSL bundle. The associated interfaces go up only when at least the specified number of wire pairs is connected and in Showtime. This variable has no effect with single pair modes. |
| INT hdsl2ShdslEndpointConfPamMode | 1.3.6.1.4.1.272.4.35.1.1.4.1.17 | INTEGER | read-write | This object specifies which modulation modes are allowed for this wire pair. 16 - 16-TCPAM, used for Annex A,B and F,G. 32 - 32-TCPAM, used for Annex F,G only. 4, 8, 64, 128 - non standard proprietary modes. On CPE site more than one mode can be allowed by adding the values. On CO site only the highest mode is used if several values are added. |
| INT hdsl2ShdslEndpointConfSide | 1.3.6.1.4.1.272.4.35.1.1.4.1.2 | INTEGER | read-write | The side of the unit associated with this segment endpoint - Network/Customer side - as per the Hdsl2ShdslUnitSide textual convention. |
| hdsl2ShdslEndpointConfTable | 1.3.6.1.4.1.272.4.35.1.1.4 | not-accessible | This table supports configuration parameters for segment endpoints in a HDSL2/SHDSL line. As this table is indexed by ifIndex, it MUST be maintained in a persistent manner. Entries in this table are created by the system only. | |
| INT hdsl2ShdslEndpointConfTotalMinLineRate | 1.3.6.1.4.1.272.4.35.1.1.4.1.18 | INTEGER | read-write | This object configures the minimum transmission rate in bits-per-second (bps) for the associated SHDSL bundle. The associated interfaces go up only when the sum of the data rates of the associated wire pairs in state Showtime reaches or exceeds the specified value. This variable has no effect with single pair modes. |
| INT hdsl2ShdslEndpointConfTransmissionMode | 1.3.6.1.4.1.272.4.35.1.1.4.1.8 | INTEGER | read-write | This object specifies the regional setting for the SHDSL line: region1 - ITU-T G.991.2 Annex A region2 - ITU-T G.991.2 Annex B |
| INT hdsl2ShdslEndpointConfWireInterface | 1.3.6.1.4.1.272.4.35.1.1.4.1.5 | INTEGER | read-write | This object configures the bonding mode of the SHDSL Line. twoWire(1) : no bonding is used fourWire(2) : four-wire mode fourWireStandard(3) : four-wire mode, disable globespan enhanced mode fourWireIMA(4) : 2 wire pairs bonded with IMA sixWire(5) : 3 wire pairs in m-pair mode sixWireIMA(6) : 3 wire pairs bonded with IMA eightWire(7) : 4 wire pairs in m-pair mode eightWireIMA(8) : 4 wire pairs bonded with IMA not-used(9) : wire pair inactive groupMember(10) : wire pair belongs to a bonding group twoWireEFM(11) : 2 wire EFM mode fourWireEFM(12) : 2 wire pairs in EFM mode with PAF bonding sixWireEFM(13) : 3 wire pairs in EFM mode with PAF bonding eightWireEFM(14) : 4 wire pairs in EFM mode with PAF bonding |
| INT hdsl2ShdslEndpointConfWorstCaseTargetMarginDown | 1.3.6.1.4.1.272.4.35.1.1.4.1.11 | INTEGER | read-write | This object specifies the downstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit. |
| INT hdsl2ShdslEndpointConfWorstCaseTargetMarginUp | 1.3.6.1.4.1.272.4.35.1.1.4.1.13 | INTEGER | read-write | This object specifies the upstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit. |
| CTR hdsl2ShdslEndpointCRCanomalies | 1.3.6.1.4.1.272.4.35.1.1.5.1.11 | Counter | read-only | Count of CRC anomalies on this endpoint since the xU was last restarted. |
| INT hdsl2ShdslEndpointCurr15MinCorrectedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.16 | INTEGER | read-only | Count of all blocks received with errors that were corrected on this channel within the mandatory 15 minute interval. |
| INT hdsl2ShdslEndpointCurr15MinCRCanomalies | 1.3.6.1.4.1.272.4.35.1.1.5.1.21 | INTEGER | read-only | Count of CRC anomalies in the current 15-minute interval. |
| INT hdsl2ShdslEndpointCurr15MinES | 1.3.6.1.4.1.272.4.35.1.1.5.1.19 | INTEGER | read-only | Count of Errored Seconds (ES) in the current 15-minute interval. |
| INT hdsl2ShdslEndpointCurr15MinLOSWS | 1.3.6.1.4.1.272.4.35.1.1.5.1.22 | INTEGER | read-only | Count of Loss of Sync Word (LOSW) Seconds in the current 15-minute interval. |
| INT hdsl2ShdslEndpointCurr15MinReceivedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.14 | INTEGER | read-only | Count of all encoded blocks received on this channel within the mandatory 15 minute interval. |
| INT hdsl2ShdslEndpointCurr15MinSES | 1.3.6.1.4.1.272.4.35.1.1.5.1.20 | INTEGER | read-only | Count of Severely Errored Seconds (SES) in the current 15-minute interval. |
| INT hdsl2ShdslEndpointCurr15MinTimeElapsed | 1.3.6.1.4.1.272.4.35.1.1.5.1.18 | INTEGER | read-only | Total elapsed seconds in the current 15-minute interval. |
| INT hdsl2ShdslEndpointCurr15MinTransmittedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.15 | INTEGER | read-only | Count of all encoded blocks transmitted on this channel within the mandatory 15 minute interval. |
| INT hdsl2ShdslEndpointCurr15MinUAS | 1.3.6.1.4.1.272.4.35.1.1.5.1.23 | INTEGER | read-only | Count of Unavailable Seconds (UAS) in the current 15-minute interval. |
| INT hdsl2ShdslEndpointCurr15MinUncorrectBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.17 | INTEGER | read-only | Count of all blocks received with uncorrectable errors on this channel within the mandatory 15 minute interval. |
| INT hdsl2ShdslEndpointCurr1DayCorrectedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.26 | INTEGER | read-only | Count of all blocks received with errors that were corrected on this channel during the mandatory day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DayCRCanomalies | 1.3.6.1.4.1.272.4.35.1.1.5.1.31 | INTEGER | read-only | Count of CRC anomalies during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DayES | 1.3.6.1.4.1.272.4.35.1.1.5.1.29 | INTEGER | read-only | Count of Errored Seconds (ES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DayLOSWS | 1.3.6.1.4.1.272.4.35.1.1.5.1.32 | INTEGER | read-only | Count of Loss of Sync Word (LOSW) Seconds during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DayReceivedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.24 | INTEGER | read-only | Count of all encoded blocks received on this channel during the mandatory day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DaySES | 1.3.6.1.4.1.272.4.35.1.1.5.1.30 | INTEGER | read-only | Count of Severely Errored Seconds (SES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DayTimeElapsed | 1.3.6.1.4.1.272.4.35.1.1.5.1.28 | INTEGER | read-only | Number of seconds that have elapsed since the beginning of the current 1-day interval. |
| INT hdsl2ShdslEndpointCurr1DayTransmittedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.25 | INTEGER | read-only | Count of all encoded blocks transmitted on this channel during the mandatory day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DayUAS | 1.3.6.1.4.1.272.4.35.1.1.5.1.33 | INTEGER | read-only | Count of Unavailable Seconds (UAS) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurr1DayUncorrectBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.27 | INTEGER | read-only | Count of all blocks received with uncorrectable errors on this channel during the mandatory day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed. |
| INT hdsl2ShdslEndpointCurrAtn | 1.3.6.1.4.1.272.4.35.1.1.5.1.6 | INTEGER | read-only | The current loop attenuation for this endpoint as reported in a Network or Customer Side Performance Status message. |
| INT hdsl2ShdslEndpointCurrCorrectedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.4 | INTEGER | read-only | Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data. |
| hdsl2ShdslEndpointCurrEntry | 1.3.6.1.4.1.272.4.35.1.1.5.1 | not-accessible | An entry in the hdsl2ShdslEndpointCurrTable. Each entry contains status and performance information relating to a single segment endpoint. It is indexed by the ifIndex of the HDSL2/SHDSL line. | |
| INT hdsl2ShdslEndpointCurrIfIndex | 1.3.6.1.4.1.272.4.35.1.1.5.1.1 | INTEGER | read-only | This object specifies the associated interface index of this HDSL2/SHDSL line. |
| INT hdsl2ShdslEndpointCurrReceivedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.2 | INTEGER | read-only | Count of all encoded blocks received on this channel since agent reset. |
| INT hdsl2ShdslEndpointCurrSnrMgn | 1.3.6.1.4.1.272.4.35.1.1.5.1.7 | INTEGER | read-only | The current SNR margin for this endpoint as reported in a Status Response/SNR message. |
| INT hdsl2ShdslEndpointCurrStatus | 1.3.6.1.4.1.272.4.35.1.1.5.1.8 | INTEGER | read-only | Contains the current state of the endpoint. This is a bitmap of possible conditions. The various bit positions are: noDefect There no defects on the line. powerBackoff Indicates enhanced Power Backoff. deviceFault Indicates a vendor-dependent diagnostic or self-test fault has been detected. dcContinuityFault Indicates vendor-dependent conditions that interfere with span powering such as short and open circuits. snrMarginAlarm Indicates that the SNR margin has dropped below the alarm threshold. loopAttenuationAlarm Indicates that the loop attenuation exceeds the alarm threshold. (not supported by GlobeSpan !) loswFailureAlarm Indicates a forward LOSW alarm. configInitFailure Endpoint failure during initialization due to paired endpoint not able to support requested configuration. protocolInitFailure Endpoint failure during initialization due to incompatible protocol used by the paired endpoint. noNeighborPresent Endpoint failure during initialization due to no activation sequence detected from paired endpoint. loopbackActive A loopback is currently active at this Segment Endpoint. This is intended to supplement ifOperStatus. Note that there is a 1-1 relationship between the status bits defined in this object and the notification thresholds defined elsewhere in this MIB. |
| hdsl2ShdslEndpointCurrTable | 1.3.6.1.4.1.272.4.35.1.1.5 | not-accessible | This table contains current status and performance information for segment endpoints in HDSL2/SHDSL Lines. As with other tables in this MIB indexed by ifIndex, entries in this table MUST be maintained in a persistent manner. Entries in this table are created by the system only. | |
| INT hdsl2ShdslEndpointCurrTransmittedBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.3 | INTEGER | read-only | Count of all encoded blocks transmitted on this channel since agent reset. |
| INT hdsl2ShdslEndpointCurrUncorrectBlks | 1.3.6.1.4.1.272.4.35.1.1.5.1.5 | INTEGER | read-only | Count of all blocks received with uncorrectable errors since agent reset. |
| CTR hdsl2ShdslEndpointES | 1.3.6.1.4.1.272.4.35.1.1.5.1.9 | Counter | read-only | Count of Errored Seconds (ES) on this endpoint since the xU was last restarted. |
| CTR hdsl2ShdslEndpointLOSWS | 1.3.6.1.4.1.272.4.35.1.1.5.1.12 | Counter | read-only | Count of Loss of Sync Word (LOSW) Seconds on this endpoint since the xU was last restarted. |
| CTR hdsl2ShdslEndpointSES | 1.3.6.1.4.1.272.4.35.1.1.5.1.10 | Counter | read-only | Count of Severely Errored Seconds (SES) on this endpoint since the xU was last restarted. |
| CTR hdsl2ShdslEndpointUAS | 1.3.6.1.4.1.272.4.35.1.1.5.1.13 | Counter | read-only | Count of Unavailable Seconds (UAS) on this endpoint since the xU was last restarted. |
| hdsl2ShdslInventoryEntry | 1.3.6.1.4.1.272.4.35.1.1.3.1 | not-accessible | An entry in the hdsl2ShdslInventoryTable. Each entry represents inventory information for a single unit in a HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line. | |
| hdsl2ShdslInventoryTable | 1.3.6.1.4.1.272.4.35.1.1.3 | not-accessible | This table supports retrieval of unit inventory information available via the EOC from units in a HDSL2/SHDSL line. Entries in this table are dynamically created during the line discovery process. The life cycle for these entries is as follows: - xtu discovers a device, either a far-end xtu or an xru - an inventory table entry is created for the device - the line goes down for whatever reason - inventory table entries for unreachable devices are destroyed. As these entries are created/destroyed dynamically, they are NOT persistent. | |
| OCT hdsl2ShdslInvEquipmentCode | 1.3.6.1.4.1.272.4.35.1.1.3.1.11 | OCTET STRING | read-only | Equipment code conforming to ANSI T1.213, Coded Identification of Equipment Entities. |
| INT hdsl2ShdslInvIfIndex | 1.3.6.1.4.1.272.4.35.1.1.3.1.1 | INTEGER | read-only | This object specifies the associated interface index of this HDSL2/SHDSL line. |
| INT hdsl2ShdslInvIndex | 1.3.6.1.4.1.272.4.35.1.1.3.1.2 | INTEGER | read-only | Each entry in this table corresponds to a physical element in a HDSL2/SHDSL Span. It is based on the EOC unit addressing scheme with reference to the xtuC. |
| INT hdsl2ShdslInvStandardVersion | 1.3.6.1.4.1.272.4.35.1.1.3.1.7 | INTEGER | read-only | Version of the HDSL2/SHDSL standard implemented, as reported in an Inventory Response message. |
| INT hdsl2ShdslInvTransmissionModeCapability | 1.3.6.1.4.1.272.4.35.1.1.3.1.13 | INTEGER | read-only | Contains the transmission mode capability of the SHDSL unit: region1 - ITU-T G.991.2 Annex A region2 - ITU-T G.991.2 Annex B |
| INT hdsl2ShdslInvVendorEOCSoftwareVersion | 1.3.6.1.4.1.272.4.35.1.1.3.1.6 | INTEGER | read-only | Vendor EOC version as reported in a Discovery Response message. |
| OCT hdsl2ShdslInvVendorID | 1.3.6.1.4.1.272.4.35.1.1.3.1.3 | OCTET STRING | read-only | Vendor ID as reported in an Inventory Response message. |
| OCT hdsl2ShdslInvVendorIssueNumber | 1.3.6.1.4.1.272.4.35.1.1.3.1.9 | OCTET STRING | read-only | Vendor issue number as reported in an Inventory Response message. |
| OCT hdsl2ShdslInvVendorListNumber | 1.3.6.1.4.1.272.4.35.1.1.3.1.8 | OCTET STRING | read-only | Vendor list number as reported in an Inventory Response message. |
| OCT hdsl2ShdslInvVendorModelNumber | 1.3.6.1.4.1.272.4.35.1.1.3.1.4 | OCTET STRING | read-only | Vendor model number as reported in an Inventory Response message. |
| OCT hdsl2ShdslInvVendorOther | 1.3.6.1.4.1.272.4.35.1.1.3.1.12 | OCTET STRING | read-only | Other vendor information as reported in an Inventory Response message. |
| OCT hdsl2ShdslInvVendorSerialNumber | 1.3.6.1.4.1.272.4.35.1.1.3.1.5 | OCTET STRING | read-only | Vendor serial number as reported in an Inventory Response message. |
| OCT hdsl2ShdslInvVendorSoftwareVersion | 1.3.6.1.4.1.272.4.35.1.1.3.1.10 | OCTET STRING | read-only | Vendor software version as reported in an Inventory Response message. |
| hdsl2ShdslLineMib | 1.3.6.1.4.1.272.4.35.1 | |||
| hdsl2ShdslMibObjects | 1.3.6.1.4.1.272.4.35.1.1 | |||
| INT hdsl2ShdslSpanConfMaxLineRate | 1.3.6.1.4.1.272.4.35.1.1.10.1.4 | INTEGER | read-write | This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. |
| INT hdsl2ShdslSpanConfMinLineRate | 1.3.6.1.4.1.272.4.35.1.1.10.1.3 | INTEGER | read-write | This object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. |
| hdsl2ShdslSpanConfProfileEntry | 1.3.6.1.4.1.272.4.35.1.1.10.1 | not-accessible | Each entry corresponds to a single span configuration profile. Each profile contains a set of span configuration parameters. The configuration parameters in a profile are applied to those lines referencing that profile (see the hdsl2ShdslSpanConfProfile object). Profiles may be created/deleted only by the system. | |
| STR hdsl2ShdslSpanConfProfileName | 1.3.6.1.4.1.272.4.35.1.1.10.1.1 | DisplayString | read-only | This object is the unique index associated with this profile. Entries in this table are referenced via the object hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry. |
| hdsl2ShdslSpanConfProfileTable | 1.3.6.1.4.1.272.4.35.1.1.10 | not-accessible | This table supports definitions of span configuration profiles for SHDSL lines. HDSL2 does not support these configuration options. This table MUST be maintained in a persistent manner. Entries in this table are created by the system only. | |
| INT hdsl2ShdslSpanConfTransmissionMode | 1.3.6.1.4.1.272.4.35.1.1.10.1.6 | INTEGER | read-write | This object specifies the regional setting for the SHDSL line: region1 - ITU-T G.991.2 Annex A region2 - ITU-T G.991.2 Annex B |
| INT hdsl2ShdslSpanConfWireInterface | 1.3.6.1.4.1.272.4.35.1.1.10.1.2 | INTEGER | read-write | This object configures the bonding mode of the SHDSL Line. twoWire(1) : no bonding is used fourWire(2) : four-wire mode fourWireStandard(3) : four-wire mode, disable globespan enhanced mode fourWireIMA(4) : 2 wire pairs bonded with IMA sixWire(5) : 3 wire pairs in m-pair mode sixWireIMA(6) : 3 wire pairs bonded with IMA eightWire(7) : 4 wire pairs in m-pair mode eightWireIMA(8) : 4 wire pairs bonded with IMA not-used(9) : wire pair inactive groupMember(10) : wire pair belongs to a bonding group twoWireEFM(11) : 2 wire EFM mode fourWireEFM(12) : 2 wire pairs in EFM mode with PAF bonding sixWireEFM(13) : 3 wire pairs in EFM mode with PAF bonding eightWireEFM(14) : 4 wire pairs in EFM mode with PAF bonding |
| INT hdsl2ShdslSpanConfWorstCaseTargetMarginDown | 1.3.6.1.4.1.272.4.35.1.1.10.1.10 | INTEGER | read-write | This object specifies the downstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit. |
| INT hdsl2ShdslSpanConfWorstCaseTargetMarginUp | 1.3.6.1.4.1.272.4.35.1.1.10.1.12 | INTEGER | read-write | This object specifies the upstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit. |
RFC description
HDSL2 and SHDSL line configuration and performance monitoring for Bianca Brick modems.
Start monitoring bintec BIANCA/BRICK ISDN/VPN routers (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.