ICOTERA-I6400-SERIES

All MIBs › ICOTERA-I6400-SERIES

Organization: Icotera A/S

Last Updated: 2017-03-01

Category: DSL and Broadband, Vendor: Icotera

Description: Icotera MIB for the I6400 series residential gateway providing DSL/fiber interface, routing, and subscriber management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ICOTERA-I6400-SERIES?

ICOTERA-I6400-SERIES is Icotera's enterprise MIB for the I6400 series residential gateway, a broadband customer-premises equipment (CPE) product supporting DSL/fiber/cable access and subscriber routing. It exposes a mix of physical-layer and hardware diagnostic objects, covering CATV/RF cable-modem parameters and optical transceiver digital diagnostic monitoring (DDM) data. It is strongly hardware-status oriented: transceiverDdmTemperature, transceiverDdmTxPower, transceiverDdmRxPower, and transceiverDdmVoltage/TxBiasCurrent give direct visibility into the optical transceiver's physical health, while catvModuleSignalDetected, catvModuleLowSignal, and catvModulePowerLevel report the RF/cable module's signal-quality and power state. As an Icotera-specific gateway MIB it is largely self-contained, though its transceiver DDM objects mirror the industry-standard SFF-8472 DDM data model used broadly across optical vendor MIBs. It is deployed on Icotera I6400 series residential/SMB gateways used by broadband service providers for last-mile access. Engineers can download the ICOTERA-I6400-SERIES file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ICOTERA-I6400-SERIES. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Icotera I6400 series residential/SMB broadband gateway

Monitoring Examples

An administrator would poll transceiverDdmRxPower and transceiverDdmTxPower together with transceiverDdmTemperature to catch a degrading optical link before it fails outright, since falling RX power combined with rising temperature often precedes a fiber transceiver fault. catvModuleSignalDetected and catvModuleLowSignal would be checked to confirm the CATV/RF module still sees a valid downstream signal, with catvModuleRflevel and catvModulePowerLevel providing the actual signal-strength readings; a low-signal flag alongside a dropping RF level points to a cable-plant or connector problem on that specific gateway.

What Can Be Monitored

optical transceiver temperature/voltage/bias current
transceiver TX/RX optical power
CATV/RF signal level and detection
low-signal alarm condition
module admin status

Imported Objects

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using curMetrTotalBytes OID:

Select an Icotera I6400 series residential/SMB broadband gateway as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type curMetrTotalBytes into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of bytes transferred within the stream. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
icotera	1.3.6.1.4.1.29865			The Icotera management information base SMI definitions
ictIGW1k	1.3.6.1.4.1.29865.11			Device related SNMP options
ictMgmt	1.3.6.1.4.1.29865.11.2
ictMgmtMib	1.3.6.1.4.1.29865.11.2.1			The MIB which allows managing the CPE
ictFwUpg	1.3.6.1.4.1.29865.11.2.1.1			The MIB of firmware upgrade
OCT upgUrl	1.3.6.1.4.1.29865.11.2.1.1.1	OCTET STRING	read-write	MIB for firmware file path declaration.
INT upgExecute	1.3.6.1.4.1.29865.11.2.1.1.2	INTEGER	read-write	MIB for firmware upgrade execution.
OCT upgStatus	1.3.6.1.4.1.29865.11.2.1.1.3	OCTET STRING	read-only	MIB used to check firmware upgrade status.
ictCfgUpdate	1.3.6.1.4.1.29865.11.2.1.2			The MIB of configuration update
OCT cfgTftpPath	1.3.6.1.4.1.29865.11.2.1.2.1	OCTET STRING	read-write	MIB for configuration file path stored at TFTP declaration.
INT cfgExecute	1.3.6.1.4.1.29865.11.2.1.2.2	INTEGER	read-write	MIB for configuration upload exectution.
OCT cfgStatus	1.3.6.1.4.1.29865.11.2.1.2.3	OCTET STRING	read-only	MIB used to check configuration upload status.
ictReboot	1.3.6.1.4.1.29865.11.2.1.3			The MIB responsible for CPE reboot
INT performCpeReboot	1.3.6.1.4.1.29865.11.2.1.3.2	INTEGER	read-write	MIB for CPE reboot execution.
ictServices	1.3.6.1.4.1.29865.11.3
ictServicesMibs	1.3.6.1.4.1.29865.11.3.1			The MIB module for managing Icotera services
ictCatv	1.3.6.1.4.1.29865.11.3.1.1			The MIB module for managing Icotera services
INT catvModuleAdminStatus	1.3.6.1.4.1.29865.11.3.1.1.1	INTEGER	read-only	The administrative status of the module, this can be enabled(1) or disabled(0).
INT catvModuleFilter	1.3.6.1.4.1.29865.11.3.1.1.2	INTEGER	read-only	Package filter selected for catv module
INT catvModuleRflevel	1.3.6.1.4.1.29865.11.3.1.1.3	INTEGER	read-only	RF signal amplification on CATV output
INT catvModuleLowSignal	1.3.6.1.4.1.29865.11.3.1.1.4	INTEGER	read-only	Low signal level of catv led
INT catvModuleSignalDetected	1.3.6.1.4.1.29865.11.3.1.1.5	INTEGER	read-only	Tells whether CATV signal is detected: yes(1) - detected, no(0) - not detected.
INT catvModulePowerLevel	1.3.6.1.4.1.29865.11.3.1.1.6	INTEGER	read-only	Current CATV power level. It can have one of the following values: - any integer between -1099 and 199 when the power level is higher than -11.00 and lower than 2.00, which is the power level in dBm multiplied by 100. - a value of -2147483648 when the power level is lower than -11 dBm - a value of 2147483647 when the power level is higher than 2 dBm.
ictTransceiver	1.3.6.1.4.1.29865.11.3.1.3			The container for DDM related MIB module
INT transceiverDdmTemperature	1.3.6.1.4.1.29865.11.3.1.3.1	INTEGER	read-only	Internally measured transceiver temperature. Represented in increments of 1/256 degrees Celsius, yielding a total range of (minus) 128C to (plus) 128C.
INT transceiverDdmTxPower	1.3.6.1.4.1.29865.11.3.1.3.2	INTEGER	read-only	Measured TX output power. Represented in increments of 1/10000 mW.
INT transceiverDdmRxPower	1.3.6.1.4.1.29865.11.3.1.3.3	INTEGER	read-only	Measured RX received optical power. Represented in increments of 1/10000 mW.
INT transceiverDdmVoltage	1.3.6.1.4.1.29865.11.3.1.3.4	INTEGER	read-only	Internally measured transceiver supply voltage. Represented in increments of 1/10000 V.
INT transceiverDdmTxBiasCurrent	1.3.6.1.4.1.29865.11.3.1.3.5	INTEGER	read-only	Measured TX bias current. Represented in increments of 1/500 mA.
INT transceiverTransceiverType	1.3.6.1.4.1.29865.11.3.1.3.6	INTEGER	read-only	Type of serial transceiver.
INT transceiverLaserWavelength	1.3.6.1.4.1.29865.11.3.1.3.7	INTEGER	read-only	TX Laser Wavelength, units of nm.
INT transceiverConnectorType	1.3.6.1.4.1.29865.11.3.1.3.8	INTEGER	read-only	Connector type provided.
INT transceiverEthernetCompliance	1.3.6.1.4.1.29865.11.3.1.3.9	INTEGER	read-only	Ethernet compliance. 8-bit bit field: Bit 7 - BASE-PX Bit 6 - BASE-BX10 Bit 5 - 100BASE-FX Bit 4 - 100BASE-LX/LX10 Bit 3 - 1000BASE-T Bit 2 - 1000BASE-CX Bit 1 - 1000BASE-LX Bit 0 - 1000BASE-SX.
INT transceiverLinkLength	1.3.6.1.4.1.29865.11.3.1.3.10	INTEGER	read-only	Link length supported for single mode fiber, units of km.
INT transceiverDiagCapable	1.3.6.1.4.1.29865.11.3.1.3.11	INTEGER	read-only	Digital diagnostic monitoring implemented.
ictReset	1.3.6.1.4.1.29865.11.5
ictFacRst	1.3.6.1.4.1.29865.11.5.1			The MIB parent for CPE reset
ictFacRstMib	1.3.6.1.4.1.29865.11.5.1.1			The MIB which makes Factory Reset of CPE
INT performFactoryReset	1.3.6.1.4.1.29865.11.5.1.1.1	INTEGER	read-write	MIB used to perform Factory Reset.
ictMcastAnalyzer	1.3.6.1.4.1.29865.11.7
ictMcastAnalyzerCurrent	1.3.6.1.4.1.29865.11.7.1
ictMcastAnalyzerCurrentList	1.3.6.1.4.1.29865.11.7.1.1		not-accessible	A list of currently analyzed multicast groups.
currentListEntry	1.3.6.1.4.1.29865.11.7.1.1.1		not-accessible	An entry containing a particular multicast group address.
INT curGroupIndex	1.3.6.1.4.1.29865.11.7.1.1.1.1	INTEGER	read-only	Index of the analyzed multicast group.
IP curGroupAddr	1.3.6.1.4.1.29865.11.7.1.1.1.2	IpAddress	read-only	The IPv4 address of this entry's multicast group.
ictMcastAnalyzerCurrentMetrics	1.3.6.1.4.1.29865.11.7.1.2		not-accessible	A list of currently analyzed multicast groups and their metrics.
currentMetricsEntry	1.3.6.1.4.1.29865.11.7.1.2.1		not-accessible	An entry containing metrics concerning a particular multicast group.
IP curMetrGroupAddr	1.3.6.1.4.1.29865.11.7.1.2.1.1	IpAddress	read-only	The IPv4 address of this entry's multicast group.
IP curMetrSourceAddr	1.3.6.1.4.1.29865.11.7.1.2.1.2	IpAddress	read-only	The source IPv4 address of this multicast stream.
I32 curMetrDstPort	1.3.6.1.4.1.29865.11.7.1.2.1.3	Integer32	read-only	The destination port number of this multicast stream.
I32 curMetrSrcPort	1.3.6.1.4.1.29865.11.7.1.2.1.4	Integer32	read-only	The source port number of this multicast stream.
C64 curMetrTotalBytesEx	1.3.6.1.4.1.29865.11.7.1.2.1.5	Counter64	read-only	The total number of bytes transferred within the stream.
C64 curMetrTotalPackets	1.3.6.1.4.1.29865.11.7.1.2.1.6	Counter64	read-only	The total number of packets transferred within the stream.
G32 curMetrKbps	1.3.6.1.4.1.29865.11.7.1.2.1.7	Gauge32	read-only	Kilobits per second during last second.
G32 curMetrPps	1.3.6.1.4.1.29865.11.7.1.2.1.8	Gauge32	read-only	Packets per second during last second.
G32 curMetrAvgKbps	1.3.6.1.4.1.29865.11.7.1.2.1.9	Gauge32	read-only	Average kilobits per second.
G32 curMetrAvgPps	1.3.6.1.4.1.29865.11.7.1.2.1.10	Gauge32	read-only	Average packets per second.
ICT curMetrMaxDelta	1.3.6.1.4.1.29865.11.7.1.2.1.11	IctDelta	read-only	Maximum time period between two successive packets from the last second.
ICT curMetrAvgDelta	1.3.6.1.4.1.29865.11.7.1.2.1.12	IctDelta	read-only	Average time period between two successive packets from the last second.
ICT curMetrTotalMaxDelta	1.3.6.1.4.1.29865.11.7.1.2.1.13	IctDelta	read-only	Maximum time period between two successive packets.
ICT curMetrTotalAvgDelta	1.3.6.1.4.1.29865.11.7.1.2.1.14	IctDelta	read-only	Average time period between two successive packets.
ICT curMetrStartTimestamp	1.3.6.1.4.1.29865.11.7.1.2.1.15	IctTimeStamp	read-only	The time at which the stream started being analyzed.
ICT curMetrStopTimestamp	1.3.6.1.4.1.29865.11.7.1.2.1.16	IctTimeStamp	read-only	The time at which the stream stopped being analyzed.
ICT curMetrMemberPorts	1.3.6.1.4.1.29865.11.7.1.2.1.17	IctPortList	read-only	LAN ports being members of the multicast group.
OCT curMetrStreamType	1.3.6.1.4.1.29865.11.7.1.2.1.18	OCTET STRING	read-only	Type of the stream: either RTP or UDP.
C32 curMetrSkips	1.3.6.1.4.1.29865.11.7.1.2.1.19	Counter32	read-only	Number of skipped MPG-TS packets during last second.
C32 curMetrDiscontinuities	1.3.6.1.4.1.29865.11.7.1.2.1.20	Counter32	read-only	Number of MPG-TS discontinuities during last second.
C32 curMetrLost	1.3.6.1.4.1.29865.11.7.1.2.1.21	Counter32	read-only	Number of lost RTP packets during last second.
C32 curMetrReordered	1.3.6.1.4.1.29865.11.7.1.2.1.22	Counter32	read-only	Number of reordered RTP packets during last second.
C32 curMetrTotalSkips	1.3.6.1.4.1.29865.11.7.1.2.1.23	Counter32	read-only	Total number of skipped MPG-TS packets.
C32 curMetrTotalDiscontinuities	1.3.6.1.4.1.29865.11.7.1.2.1.24	Counter32	read-only	Total number of MPG-TS discontinuities.
C32 curMetrTotalLost	1.3.6.1.4.1.29865.11.7.1.2.1.25	Counter32	read-only	Total number of lost RTP packets.
C32 curMetrTotalReordered	1.3.6.1.4.1.29865.11.7.1.2.1.26	Counter32	read-only	Total number of reordered RTP packets.
G32 curMetrAvgLostPps	1.3.6.1.4.1.29865.11.7.1.2.1.27	Gauge32	read-only	Average number of lost RTP packets per second.
ICT curMetrJitter	1.3.6.1.4.1.29865.11.7.1.2.1.28	IctJitter	read-only	Jitter calculated for the last second.
ictMcastAnalyzerHistory	1.3.6.1.4.1.29865.11.7.2
ictMcastAnalyzerHistoryList	1.3.6.1.4.1.29865.11.7.2.1		not-accessible	A list of formerly analyzed multicast groups.
historyListEntry	1.3.6.1.4.1.29865.11.7.2.1.1		not-accessible	An entry containing a particular multicast group address.
INT histGroupIndex	1.3.6.1.4.1.29865.11.7.2.1.1.1	INTEGER	read-only	Index of the historical multicast group.
IP histGroupAddr	1.3.6.1.4.1.29865.11.7.2.1.1.2	IpAddress	read-only	The IPv4 address of this entry's multicast group.
ictMcastAnalyzerHistoryMetrics	1.3.6.1.4.1.29865.11.7.2.2		not-accessible	A list of formerly analyzed multicast groups and their metrics.
historyMetricsEntry	1.3.6.1.4.1.29865.11.7.2.2.1		not-accessible	An entry containing metrics concerning a particular multicast group.
IP histMetrGroupAddr	1.3.6.1.4.1.29865.11.7.2.2.1.1	IpAddress	read-only	The IPv4 address of this entry's multicast group.
IP histMetrSourceAddr	1.3.6.1.4.1.29865.11.7.2.2.1.2	IpAddress	read-only	The source IPv4 address of this multicast stream.
I32 histMetrDstPort	1.3.6.1.4.1.29865.11.7.2.2.1.3	Integer32	read-only	The destination port number of this multicast stream.
I32 histMetrSrcPort	1.3.6.1.4.1.29865.11.7.2.2.1.4	Integer32	read-only	The source port number of this multicast stream.
C64 histMetrTotalBytes	1.3.6.1.4.1.29865.11.7.2.2.1.5	Counter64	read-only	The total number of bytes transferred within the stream.
C64 histMetrTotalPackets	1.3.6.1.4.1.29865.11.7.2.2.1.6	Counter64	read-only	The total number of packets transferred within the stream.
G32 histMetrKbps	1.3.6.1.4.1.29865.11.7.2.2.1.7	Gauge32	read-only	Kilobits per second during last second.
G32 histMetrPps	1.3.6.1.4.1.29865.11.7.2.2.1.8	Gauge32	read-only	Packets per second during last second.
G32 histMetrAvgKbps	1.3.6.1.4.1.29865.11.7.2.2.1.9	Gauge32	read-only	Average kilobits per second.
G32 histMetrAvgPps	1.3.6.1.4.1.29865.11.7.2.2.1.10	Gauge32	read-only	Average packets per second.
ICT histMetrMaxDelta	1.3.6.1.4.1.29865.11.7.2.2.1.11	IctDelta	read-only	Maximum time period between two successive packets from the last second.
ICT histMetrAvgDelta	1.3.6.1.4.1.29865.11.7.2.2.1.12	IctDelta	read-only	Average time period between two successive packets from the last second.
ICT histMetrTotalMaxDelta	1.3.6.1.4.1.29865.11.7.2.2.1.13	IctDelta	read-only	Maximum time period between two successive packets.
ICT histMetrTotalAvgDelta	1.3.6.1.4.1.29865.11.7.2.2.1.14	IctDelta	read-only	Average time period between two successive packets.
ICT histMetrStartTimestamp	1.3.6.1.4.1.29865.11.7.2.2.1.15	IctTimeStamp	read-only	The time at which the stream started being analyzed.
ICT histMetrStopTimestamp	1.3.6.1.4.1.29865.11.7.2.2.1.16	IctTimeStamp	read-only	The time at which the stream stopped being analyzed.
ICT histMetrMemberPorts	1.3.6.1.4.1.29865.11.7.2.2.1.17	IctPortList	read-only	LAN ports being members of the multicast group.
OCT histMetrStreamType	1.3.6.1.4.1.29865.11.7.2.2.1.18	OCTET STRING	read-only	Type of the stream: either RTP or UDP.
C32 histMetrSkips	1.3.6.1.4.1.29865.11.7.2.2.1.19	Counter32	read-only	Number of skipped MPG-TS packets during last second.
C32 histMetrDiscontinuities	1.3.6.1.4.1.29865.11.7.2.2.1.20	Counter32	read-only	Number of MPG-TS discontinuities during last second.
C32 histMetrLost	1.3.6.1.4.1.29865.11.7.2.2.1.21	Counter32	read-only	Number of lost RTP packets during last second.
C32 histMetrReordered	1.3.6.1.4.1.29865.11.7.2.2.1.22	Counter32	read-only	Number of reordered RTP packets during last second.
C32 histMetrTotalSkips	1.3.6.1.4.1.29865.11.7.2.2.1.23	Counter32	read-only	Total number of skipped MPG-TS packets.
C32 histMetrTotalDiscontinuities	1.3.6.1.4.1.29865.11.7.2.2.1.24	Counter32	read-only	Total number of MPG-TS discontinuities.
C32 histMetrTotalLost	1.3.6.1.4.1.29865.11.7.2.2.1.25	Counter32	read-only	Total number of lost RTP packets.
C32 histMetrTotalReordered	1.3.6.1.4.1.29865.11.7.2.2.1.26	Counter32	read-only	Total number of reordered RTP packets.
G32 histMetrAvgLostPps	1.3.6.1.4.1.29865.11.7.2.2.1.27	Gauge32	read-only	Average number of lost RTP packets per second.
ICT histMetrJitter	1.3.6.1.4.1.29865.11.7.2.2.1.28	IctJitter	read-only	Jitter calculated for the last second.

RFC description

Provides management objects for Icotera i6400-series CPE (Customer Premise Equipment). Supports monitoring and configuration of this product family.

Start monitoring Icotera I6400 series residential/SMB broadband gateway with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ICOTERA-I6400-SERIES