ATEN-PE-CFG-STR

All MIBs › ATEN-PE-CFG-STR

Organization: ATEN

Last Updated: 2013-10-31

Category: Textual Conventions and Registries, Vendor: ATEN

Description: Defines string data structures and configuration objects used by ATEN PE series PDU management MIBs.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ATEN-PE-CFG-STR?

ATEN-PE-CFG-STR is an ATEN enterprise MIB defining the string/configuration data structures used by ATEN's PE-series power distribution unit (PDU) management MIBs, mounted under enterprises.aten.atenProducts.overip.poweroverip.pe. It exposes device-level electrical telemetry through deviceValueTable (deviceCurrent, deviceVoltage, devicePower, devicePowerDissipation, devicePowerFactor) and equivalent per-outlet telemetry in outletValueTable, alongside a sensorValueTable reporting temperature, humidity, and pressure from up to six environmental sensors. deviceConfigTable and deviceSensorTresholdTable hold minimum/maximum measurement thresholds for current, voltage, power, and environmental readings, while per-outlet objects (outlet1Status through outlet27Status and beyond) allow both status display and remote on/off/reboot control. POP (Power Outlet Protection) and CAP (Current Awareness Protection) objects add configurable overload-protection modes and per-outlet priority for controlled shutdown sequencing. It is deployed on ATEN PE-series switched/metered rack PDUs, and administrators can download the ATEN-PE-CFG-STR MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ATEN-PE-CFG-STR. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ATEN PE-series managed/switched PDUs

Monitoring Examples

An operator polls deviceCurrent and deviceMaxCurMT to check whether total PDU load is approaching its configured maximum-current threshold, and reviews individual outletNStatus values; an outlet reporting fault(5) alongside device current near its threshold would indicate an overloaded outlet that POP protection may soon shut down.

What Can Be Monitored

device and per-outlet current/voltage/power/power-factor
environmental sensor temperature/humidity/pressure
configurable measurement thresholds
per-outlet on/off/reboot status
POP (power protection) and CAP priority mode settings
door sensor status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Gauge
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

From SNMP-USER-BASED-SM-MIB

KeyChange

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE

From SNMPv2-TC

TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
aten	1.3.6.1.4.1.21317			ATEN PE MIB
atenProducts	1.3.6.1.4.1.21317.1
overip	1.3.6.1.4.1.21317.1.3
poweroverip	1.3.6.1.4.1.21317.1.3.2
pe	1.3.6.1.4.1.21317.1.3.2.2
userManagement	1.3.6.1.4.1.21317.1.3.2.2.1
usrListTable	1.3.6.1.4.1.21317.1.3.2.2.1.1		not-accessible	A list of user. The number of user is given by the value of usrcfgNumber.
usrListEntry	1.3.6.1.4.1.21317.1.3.2.2.1.1.1		not-accessible	Status and parameter values for a pe8208 user.
INT usrIndex	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.1	INTEGER	read-only	The value of usrIndex for the user. We have 1 administrator and 8 users. The index 9 will be the administrator.
INT usrType	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.2	INTEGER	read-only	The user's type.
STR usrName	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.3	DisplayString	read-write	A textual string containing name of the user. string length: 1~16
STR usrPassword	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.4	DisplayString	read-write	A textual string containing password of the user. string length: 1~16
INT usrPort1Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.5	INTEGER	read-write	Display or set this user's outlet 1 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort2Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.6	INTEGER	read-write	Display or set this user's outlet 2 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort3Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.7	INTEGER	read-write	Display or set this user's outlet 3 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort4Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.8	INTEGER	read-write	Display or set this user's outlet 4 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort5Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.9	INTEGER	read-write	Display or set this user's outlet 5 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort6Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.10	INTEGER	read-write	Dispaly or set this user's outlet 6 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort7Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.11	INTEGER	read-write	Display or set this user's outlet 7 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort8Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.12	INTEGER	read-write	Display or set this user's outlet 8 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort9Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.13	INTEGER	read-write	Display or set this user's outlet 9 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort10Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.14	INTEGER	read-write	Display or set this user's outlet 10 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort11Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.15	INTEGER	read-write	Display or set this user's outlet 11 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort12Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.16	INTEGER	read-write	Display or set this user's outlet 12 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort13Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.17	INTEGER	read-write	Display or set this user's outlet 13 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort14Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.18	INTEGER	read-write	Display or set this user's outlet 14 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort15Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.19	INTEGER	read-write	Display or set this user's outlet 15 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort16Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.20	INTEGER	read-write	Display or set this user's outlet 16 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort17Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.21	INTEGER	read-write	Display or set this user's outlet 17 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort18Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.22	INTEGER	read-write	Display or set this user's outlet 18 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort19Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.23	INTEGER	read-write	Display or set this user's outlet 19 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort20Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.24	INTEGER	read-write	Display or set this user's outlet 20 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort21Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.25	INTEGER	read-write	Display or set this user's outlet 21 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort22Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.26	INTEGER	read-write	Display or set this user's outlet 22 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort23Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.27	INTEGER	read-write	Display or set this user's outlet 23 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort24Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.28	INTEGER	read-write	Display or set this user's outlet 24 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort25Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.29	INTEGER	read-write	Display or set this user's outlet 25 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort26Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.30	INTEGER	read-write	Display or set this user's outlet 26 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort27Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.31	INTEGER	read-write	Display or set this user's outlet 27 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort28Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.32	INTEGER	read-write	Display or set this user's outlet 28 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort29Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.33	INTEGER	read-write	Display or set this user's outlet 29 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort30Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.34	INTEGER	read-write	Display or set this user's outlet 30 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort31Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.35	INTEGER	read-write	Display or set this user's outlet 31 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort32Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.36	INTEGER	read-write	Display or set this user's outlet 32 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort33Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.37	INTEGER	read-write	Display or set this user's outlet 33 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort34Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.38	INTEGER	read-write	Display or set this user's outlet 34 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort35Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.39	INTEGER	read-write	Display or set this user's outlet 35 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort36Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.40	INTEGER	read-write	Display or set this user's outlet 36 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort37Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.41	INTEGER	read-write	Display or set this user's outlet 37 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort38Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.42	INTEGER	read-write	Display or set this user's outlet 38 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort39Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.43	INTEGER	read-write	Display or set this user's outlet 39 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort40Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.44	INTEGER	read-write	Display or set this user's outlet 40 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort41Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.45	INTEGER	read-write	Display or set this user's outlet 41 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrPort42Auth	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.46	INTEGER	read-write	Display or set this user's outlet 42 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
INT usrEnable	1.3.6.1.4.1.21317.1.3.2.2.1.1.1.47	INTEGER	read-write	Display or set this user is enable or not
control	1.3.6.1.4.1.21317.1.3.2.2.2
device	1.3.6.1.4.1.21317.1.3.2.2.2.1
STR modelName	1.3.6.1.4.1.21317.1.3.2.2.2.1.1	DisplayString	read-only	Indicate PE device model name.
STR deviceName	1.3.6.1.4.1.21317.1.3.2.2.2.1.2	DisplayString	read-write	The name of PE device. string length: 1~39 NOTE: Input string as /empty to set this object to NULL.
deviceValueTable	1.3.6.1.4.1.21317.1.3.2.2.2.1.3		not-accessible	Device value table. This table displays device's current, voltage, power and power dissipation.
deviceValueEntry	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1		not-accessible	Single deviceValue entry containing device info.
INT deviceValueIndex	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.1	INTEGER	read-only	Index of deviceValue.
STR deviceCurrent	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.2	DisplayString	read-only	Device electric current value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR deviceVoltage	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.3	DisplayString	read-only	Device voltage value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR devicePower	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.4	DisplayString	read-only	Device power value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR devicePowerDissipation	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.5	DisplayString	read-only	Device power dissipation value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
INT inputMaxVoltage	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.6	INTEGER	read-only	Device input Voltage value. unit:(V) If the device does not support this OID, we show value 0.
INT inputMaxCurrent	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.7	INTEGER	read-only	Device input Current value. unit:(A) If the device does not support this OID, we show value 0.
INT powerCapacity	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.8	INTEGER	read-only	Device power Capacity value.unit:(VA) If the device does not support this OID, we show value 0.
STR devicePowerFactor	1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.9	DisplayString	read-only	Device power Factor value. If the device does not support this OID, it returns: not-support.
sensorValueTable	1.3.6.1.4.1.21317.1.3.2.2.2.1.4		not-accessible	Device's sensor value table. This table displays sensor's temperature, humidity and pressure.
sensorValueEntry	1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1		not-accessible	Single device's sensor value entry containing device info.
INT sensorValueIndex	1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.1	INTEGER	read-only	Index of sensor number.
STR sensorTemperature	1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.2	DisplayString	read-only	Sensor's Temperature value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR sensorHumidity	1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.3	DisplayString	read-only	Sensor's Humidity value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR sensorPressure	1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.4	DisplayString	read-only	Sensor's Pressure value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
INT sensorProperty	1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.5	INTEGER	read-only	Sensor's Property.
deviceOutletStatusTable	1.3.6.1.4.1.21317.1.3.2.2.2.1.5		not-accessible	Device outlet status value table.
deviceOutletStatusEntry	1.3.6.1.4.1.21317.1.3.2.2.2.1.5.1		not-accessible	Single deviceOutletStatus entry containing device info.
INT deviceOutletStatusIndex	1.3.6.1.4.1.21317.1.3.2.2.2.1.5.1.1	INTEGER	read-only	Index of deviceOutletStatus
INT displayOutletStatus	1.3.6.1.4.1.21317.1.3.2.2.2.1.5.1.2	INTEGER	read-only	Display outlet status.
deviceConfigTable	1.3.6.1.4.1.21317.1.3.2.2.2.1.6		not-accessible	Device configuration table
deviceConfigEntry	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1		not-accessible	Single deviceConfig entry containing device info.
INT deviceConfigIndex	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.1	INTEGER	read-only	Index of deviceConfig
INT deviceMinCurMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.2	INTEGER	read-write	Display or set device minimum electric current measurement threshold. Example: range 0.0~32.0 represents 0~320. NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT deviceMaxCurMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.3	INTEGER	read-write	Display or set device maximum electric current measurement threshold. Example: range 0.0~32.0 represents 0~320 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT deviceMinVolMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.4	INTEGER	read-write	Display or set device minimum voltage measurement threshold. Exapmple: range 90.0~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT deviceMaxVolMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.5	INTEGER	read-write	Display or set device maximum voltage measurement threshold. Example: range 90.0~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT deviceMinPMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.6	INTEGER	read-write	Display or set device minimum power measurement threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT deviceMaxPMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.7	INTEGER	read-write	Display or set device maximum power measurement threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT deviceMaxPDMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.8	INTEGER	read-write	Display or set device maximum power dissipation measurement threshold. Example: range 0.0 ~ 99999.0 represents 0~999990 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
deviceSensorTresholdTable	1.3.6.1.4.1.21317.1.3.2.2.2.1.7		not-accessible	Device environment value table
deviceSensorTresholdEntry	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1		not-accessible	Device's sensor Environment entry containing sensor info.
INT deviceSensorTresholdIndex	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.1	INTEGER	read-only	Index of sensor number
INT sensorMinTempMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.2	INTEGER	read-write	Display or set sensor minimum temperature measurement threshold. Example: range -20.0 ~ 60.0 represents -200~600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT sensorMaxTempMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.3	INTEGER	read-write	Display or set sensor maximum temperature measurement threshold. Example: range -20.0 ~ 60.0 represents -200~600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT sensorMinHumMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.4	INTEGER	read-write	Display or set sensor minimum humidity measurement threshold. Example: range 15.0 ~ 95.0 represents 150~950 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT sensorMaxHumMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.5	INTEGER	read-write	Display or set sensor maximum humidity measurement threshold. Example: range 15.0 ~ 95.0 represents 150~950 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT sensorMinPressMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.6	INTEGER	read-write	Display or set sensor minimum pressure measurement threshold. Example: range -250.0 ~ 250.0 represents -2500 ~ 2500 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT sensorMaxPressMT	1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.7	INTEGER	read-write	Display or set sensor maximum pressure measurement threshold. Example: range -250.0 ~ 250.0 represents -2500 ~ 2500 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT deviceOutletControl	1.3.6.1.4.1.21317.1.3.2.2.2.1.8	INTEGER	read-write	This function is used for all outlet ports control. Set off(1) to turn off for all outlet ports. Set on(2) to turn on for all outlet ports. Get this object always return nostatus(3), because there is no device status.
INT deviceOutletReboot	1.3.6.1.4.1.21317.1.3.2.2.2.1.9	INTEGER	read-write	This function is used for all outlet ports to reboot. Only when outlet status is ON can do outlet reboot action to all ports. Set yes(2) to reboot all outlet ports. Get this object always return no(1).
INT switchable	1.3.6.1.4.1.21317.1.3.2.2.2.1.10	INTEGER	read-only	Outlet is switchable or not.
INT perportreading	1.3.6.1.4.1.21317.1.3.2.2.2.1.11	INTEGER	read-only	Outlet is per-port reading or not.
INT sensornumber	1.3.6.1.4.1.21317.1.3.2.2.2.1.12	INTEGER	read-only	Sensor number.
INT outletnumber	1.3.6.1.4.1.21317.1.3.2.2.2.1.13	INTEGER	read-only	Outlet number.
INT banknumber	1.3.6.1.4.1.21317.1.3.2.2.2.1.14	INTEGER	read-only	Bank number.
doorSensor	1.3.6.1.4.1.21317.1.3.2.2.2.1.16
INT doorSensorStatus	1.3.6.1.4.1.21317.1.3.2.2.2.1.16.1	INTEGER	read-only	Display door sensor status. close(0) represents door close. open(1) represents door open. not-attached(2) represents door sensor don't attach to device.
INT doorSensorType	1.3.6.1.4.1.21317.1.3.2.2.2.1.16.2	INTEGER	read-write	Door Sensor Type Selection
pop	1.3.6.1.4.1.21317.1.3.2.2.2.1.17
INT enablePOPmode	1.3.6.1.4.1.21317.1.3.2.2.2.1.17.1	INTEGER	read-write	Enable/Disable POP mode.
INT popThreshold	1.3.6.1.4.1.21317.1.3.2.2.2.1.17.2	INTEGER	read-write	(-1)means default value same as Bank Max Current 16 A. Example: range 0.0~32.0 represents 0~320 You can define the POP threshold or set as default(-1) value.
INT enableOutletPOPmode	1.3.6.1.4.1.21317.1.3.2.2.2.1.17.3	INTEGER	read-write	Enable/Disable Outlet POP mode.
INT enableLIFOPOPmode	1.3.6.1.4.1.21317.1.3.2.2.2.1.17.4	INTEGER	read-write	Enable/Disable LIFO POP mode.
INT enablePriorityPOPmode	1.3.6.1.4.1.21317.1.3.2.2.2.1.17.5	INTEGER	read-write	Enable/Disable Priority POP mode.
cap	1.3.6.1.4.1.21317.1.3.2.2.2.1.18
INT enableCAPmode	1.3.6.1.4.1.21317.1.3.2.2.2.1.18.1	INTEGER	read-write	Enable/Disable CAP mode.
outletCAPTable	1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2		not-accessible	Outlet CAP table
outletCAPEntry	1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2.1		not-accessible	Outlet CAP entry containing CAP info.
INT outletCAPIndex	1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2.1.1	INTEGER	read-only	Index of outlet's CAP configuration
INT outletCAPPriority	1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2.1.2	INTEGER	read-write	Display or set the CAP Priority of outlet. Priority 0 means this outlet does not support this OID.
INT outletInitMode	1.3.6.1.4.1.21317.1.3.2.2.2.1.19	INTEGER	read-write	choose outlet init mode you want.
outlet	1.3.6.1.4.1.21317.1.3.2.2.2.2
outletValueTable	1.3.6.1.4.1.21317.1.3.2.2.2.2.1		not-accessible	Display total outlet value table
outletValueEntry	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1		not-accessible	Single outletValue entry containing outlet info.
INT outletValueIndex	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.1	INTEGER	read-only	Index of outlet number
STR outletCurrent	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.2	DisplayString	read-only	Outlet electric current value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR outletVoltage	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.3	DisplayString	read-only	Outlet voltage value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR outletPower	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.4	DisplayString	read-only	Outlet power value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR outletPowerDissipation	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.5	DisplayString	read-only	Outlet power dissipation value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
INT outletMaxCurrent	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.6	INTEGER	read-only	Outlet Max Current value. unit: (A). If the device does not support this OID, we show value 0.
STR outletPowerFactor	1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.7	DisplayString	read-only	Outlet Power Factor value. If the device does not support this OID, it returns: not-support.
INT outlet1Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.2	INTEGER	read-write	Display and control outlet 1 status. Can't set pending status.
INT outlet2Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.3	INTEGER	read-write	Display and control outlet 2 status. Can't set pending status.
INT outlet3Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.4	INTEGER	read-write	Display and control outlet 3 status. Can't set pending status.
INT outlet4Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.5	INTEGER	read-write	Display and control outlet 4 status. Can't set pending status.
INT outlet5Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.6	INTEGER	read-write	Display and control outlet 5 status. Can't set pending status.
INT outlet6Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.7	INTEGER	read-write	Display and control outlet 6 status. Can't set pending status.
INT outlet7Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.8	INTEGER	read-write	Display and control outlet 7 status. Can't set pending status.
INT outlet8Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.9	INTEGER	read-write	Display and control outlet 8 status. Can't set pending status.
outletConfigTable	1.3.6.1.4.1.21317.1.3.2.2.2.2.10		not-accessible	Outlet configuration table
outletConfigEntry	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1		not-accessible	Outlet Config entry containing outlet info.
INT outletConfigIndex	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.1	INTEGER	read-only	Index of outlet number
STR outletName	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.2	DisplayString	read-write	Display or set the name of outlet. If the device does not support this OID, we show n/a. string length: 0~15 NOTE: Input string as /empty to set this object to NULL.
INT outletConfirmation	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.3	INTEGER	read-write	Display or set the confirmation of outlet.
INT outletOnDelayTime	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.4	INTEGER	read-write	Display or set the ON delay time of outlet. When this model does not support the OID, we show value -1.
INT outletOffDelayTime	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.5	INTEGER	read-write	Display or set the OFF delay time of outlet. When this model does not support the OID, we show value -1.
INT outletShutdownMethod	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.6	INTEGER	read-write	Display or set the shutdown mehtod of outlet.
STR outletMAC	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.7	DisplayString	read-write	Display or set the MAC address of ShutdownMethod. If the device does not support this OID, we show n/a. string length: 12
INT outletMinCurMT	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.8	INTEGER	read-write	Display or set the outlet minimum electric current measurment threshold. Example: range 0.0 ~16.0 rerpresnts 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT outletMaxCurMT	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.9	INTEGER	read-write	Display or set the outlet maximum electric current measurment threshold. Example: range 0.0 ~16.0 represents 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT outletMinVolMT	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.10	INTEGER	read-write	Display or set the outlet minimum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT outletMaxVolMT	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.11	INTEGER	read-write	Display or set the outlet maximum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT outletMinPMT	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.12	INTEGER	read-write	Display or set the outlet minimum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT outletMaxPMT	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.13	INTEGER	read-write	Display or set the outlet maximum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT outletMaxPDMT	1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.14	INTEGER	read-write	Display or set the outlet maximum power dissipation measurment threshold. Example: range 0.0 ~ 99999.0 represents 0~999990 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT outlet9Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.11	INTEGER	read-write	Display and control outlet 9 status. Can't set pending status.
INT outlet10Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.12	INTEGER	read-write	Display and control outlet 10 status. Can't set pending status.
INT outlet11Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.13	INTEGER	read-write	Display and control outlet 11 status. Can't set pending status.
INT outlet12Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.14	INTEGER	read-write	Display and control outlet 12 status. Can't set pending status.
INT outlet13Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.15	INTEGER	read-write	Display and control outlet 13 status. Can't set pending status.
INT outlet14Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.16	INTEGER	read-write	Display and control outlet 14 status. Can't set pending status.
INT outlet15Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.17	INTEGER	read-write	Display and control outlet 15 status. Can't set pending status.
INT outlet16Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.18	INTEGER	read-write	Display and control outlet 16 status. Can't set pending status.
INT outlet17Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.19	INTEGER	read-write	Display and control outlet 17 status. Can't set pending status.
INT outlet18Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.20	INTEGER	read-write	Display and control outlet 18 status. Can't set pending status.
INT outlet19Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.21	INTEGER	read-write	Display and control outlet 19 status. Can't set pending status.
INT outlet20Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.22	INTEGER	read-write	Display and control outlet 20 status. Can't set pending status.
INT outlet21Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.23	INTEGER	read-write	Display and control outlet 21 status. Can't set pending status.
INT outlet22Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.24	INTEGER	read-write	Display and control outlet 22 status. Can't set pending status.
INT outlet23Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.25	INTEGER	read-write	Display and control outlet 23 status. Can't set pending status.
INT outlet24Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.26	INTEGER	read-write	Display and control outlet 24 status. Can't set pending status.
INT outlet25Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.27	INTEGER	read-write	Display and control outlet 25 status. Can't set pending status.
INT outlet26Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.28	INTEGER	read-write	Display and control outlet 26 status. Can't set pending status.
INT outlet27Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.29	INTEGER	read-write	Display and control outlet 27 status. Can't set pending status.
INT outlet28Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.30	INTEGER	read-write	Display and control outlet 28 status. Can't set pending status.
INT outlet29Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.31	INTEGER	read-write	Display and control outlet 29 status. Can't set pending status.
INT outlet30Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.32	INTEGER	read-write	Display and control outlet 30 status. Can't set pending status.
INT outlet31Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.33	INTEGER	read-write	Display and control outlet 31 status. Can't set pending status.
INT outlet32Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.34	INTEGER	read-write	Display and control outlet 32 status. Can't set pending status.
INT outlet33Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.35	INTEGER	read-write	Display and control outlet 33 status. Can't set pending status.
INT outlet34Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.36	INTEGER	read-write	Display and control outlet 34 status. Can't set pending status.
INT outlet35Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.37	INTEGER	read-write	Display and control outlet 35 status. Can't set pending status.
INT outlet36Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.38	INTEGER	read-write	Display and control outlet 36 status. Can't set pending status.
INT outlet37Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.39	INTEGER	read-write	Display and control outlet 37 status. Can't set pending status.
INT outlet38Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.40	INTEGER	read-write	Display and control outlet 38 status. Can't set pending status.
INT outlet39Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.41	INTEGER	read-write	Display and control outlet 39 status. Can't set pending status.
INT outlet40Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.42	INTEGER	read-write	Display and control outlet 40 status. Can't set pending status.
INT outlet41Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.43	INTEGER	read-write	Display and control outlet 41 status. Can't set pending status.
INT outlet42Status	1.3.6.1.4.1.21317.1.3.2.2.2.2.44	INTEGER	read-write	Display and control outlet 42 status. Can't set pending status.
outletSwitchableTable	1.3.6.1.4.1.21317.1.3.2.2.2.2.70		not-accessible
outletSwitchableEntry	1.3.6.1.4.1.21317.1.3.2.2.2.2.70.1		not-accessible
INT outletSwitchableIndex	1.3.6.1.4.1.21317.1.3.2.2.2.2.70.1.1	INTEGER	read-only	Index of outlet number.
INT outletSwitchable	1.3.6.1.4.1.21317.1.3.2.2.2.2.70.1.2	INTEGER	read-only
bank	1.3.6.1.4.1.21317.1.3.2.2.2.3
breakerStatusTable	1.3.6.1.4.1.21317.1.3.2.2.2.3.1		not-accessible	Display total bank value table
breakerStatusEntry	1.3.6.1.4.1.21317.1.3.2.2.2.3.1.1		not-accessible	Single bankValue entry containing bank info.
INT breakerStatusIndex	1.3.6.1.4.1.21317.1.3.2.2.2.3.1.1.1	INTEGER	read-only	Index of breaker number.
INT breakerStatus	1.3.6.1.4.1.21317.1.3.2.2.2.3.1.1.2	INTEGER	read-only	Breaker status.
bankValueTable	1.3.6.1.4.1.21317.1.3.2.2.2.3.2		not-accessible	Display total bank value table
bankValueEntry	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1		not-accessible	Single bankValue entry containing bank info.
INT bankValueIndex	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.1	INTEGER	read-only	Index of bank number
STR bankCurrent	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.2	DisplayString	read-only	Bank electric current value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR bankVoltage	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.3	DisplayString	read-only	Bank voltage value. We put this OID to write access type for user to set the reference voltage on EC1000 model. And the setting should be the numbers. You can set 0 to clear the setting. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR bankPower	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.4	DisplayString	read-only	Bank power value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
STR bankPowerDissipation	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.5	DisplayString	read-only	Bank power dissipation value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
INT bankMaxCurrent	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.6	INTEGER	read-only	The Bank Max Current value. unit: (A) EC1000:0A~320A
INT bankAttachStatus	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.7	INTEGER	read-only	The status of Energy sensor Bank attached status.
STR bankPowerFactor	1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.8	DisplayString	read-only	Bank Power Factor value. If the device does not support this OID, it returns: not-support.
bankConfigTable	1.3.6.1.4.1.21317.1.3.2.2.2.3.3		not-accessible	Bank configuration table
bankConfigEntry	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1		not-accessible	Bank Config entry containing Bank info.
INT bankConfigIndex	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.1	INTEGER	read-only	Index of bank number
STR bankName	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.2	DisplayString	read-write	Display or set the name of bank. When this model does not support the OID, we show n/a. string length: 0~15 NOTE: Input string as /empty to set this object to NULL.
INT bankMinCurMT	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.3	INTEGER	read-write	Display or set the outlet minimum electric current measurment threshold. Example: range 0.0 ~16.0 rerpresnts 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT bankMaxCurMT	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.4	INTEGER	read-write	Display or set the outlet maximum electric current measurment threshold. Example: range 0.0 ~16.0 represents 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT bankMinVolMT	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.5	INTEGER	read-write	Display or set the outlet minimum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT bankMaxVolMT	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.6	INTEGER	read-write	Display or set the outlet maximum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT bankMinPMT	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.7	INTEGER	read-write	Display or set the outlet minimum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT bankMaxPMT	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.8	INTEGER	read-write	Display or set the outlet maximum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
INT bankMaxPDMT	1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.9	INTEGER	read-write	Display or set the outlet maximum power dissipation measurment threshold. Example: range 0.0 ~ 99999.0 represents 0~999990 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
bankControlTable	1.3.6.1.4.1.21317.1.3.2.2.2.3.4		not-accessible	Bank Control table
bankControlEntry	1.3.6.1.4.1.21317.1.3.2.2.2.3.4.1		not-accessible	Bank control entry.
INT bankControlIndex	1.3.6.1.4.1.21317.1.3.2.2.2.3.4.1.1	INTEGER	read-only	Index of bank number
INT bankControlStatus	1.3.6.1.4.1.21317.1.3.2.2.2.3.4.1.2	INTEGER	read-write	This function is used for outlet control of bank. Set off(1) to turn off for outlet control of bank. Set on(2) to turn on for all outlet control of bank. Set reboot(3) to turn on for outlet control of bank. Get this object always return nostatus(3), because there is no bank status.
deviceManagement	1.3.6.1.4.1.21317.1.3.2.2.3
config	1.3.6.1.4.1.21317.1.3.2.2.3.4
STR deviceMAC	1.3.6.1.4.1.21317.1.3.2.2.3.4.1	DisplayString	read-only	Display device MAC address.
IP deviceIPv4	1.3.6.1.4.1.21317.1.3.2.2.3.4.2	IpAddress	read-only	Display device IP address.
STR deviceFWversion	1.3.6.1.4.1.21317.1.3.2.2.3.4.3	DisplayString	read-only	Display device FW version.
dashBoard	1.3.6.1.4.1.21317.1.3.2.2.3.4.4
INT dashboardRow	1.3.6.1.4.1.21317.1.3.2.2.3.4.4.1	INTEGER	read-write	Display or set device's dashboard row number.
INT dashboardColumn	1.3.6.1.4.1.21317.1.3.2.2.3.4.4.2	INTEGER	read-write	Display or set device's dashboard column number.
STR dashboardRackName	1.3.6.1.4.1.21317.1.3.2.2.3.4.4.3	DisplayString	read-write	Display or set device's dashboard rack name. string length: 1~32 NOTE: Input string as /empty to set this object to NULL.
servicePorts	1.3.6.1.4.1.21317.1.3.2.2.3.4.5
INT httpPort	1.3.6.1.4.1.21317.1.3.2.2.3.4.5.1	INTEGER	read-write	Display or set the HTTP port of PE device.
INT httpsPort	1.3.6.1.4.1.21317.1.3.2.2.3.4.5.2	INTEGER	read-write	Display or set the HTTPs port of PE device.
INT httpsOnlyEnable	1.3.6.1.4.1.21317.1.3.2.2.3.4.5.3	INTEGER	read-write	Enable to use Webpage HTTPs only or disable to use Webpage HTTP/HTTPs
ipv4config	1.3.6.1.4.1.21317.1.3.2.2.3.4.6
INT staticIPEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.6.1	INTEGER	read-write	Display or set IPv4 address automatically or not
IP fixedIPv4	1.3.6.1.4.1.21317.1.3.2.2.3.4.6.2	IpAddress	read-write	Display or set fixed IPv4 address
IP subnetMask	1.3.6.1.4.1.21317.1.3.2.2.3.4.6.3	IpAddress	read-write	Display or set subnet mask address
IP gateway	1.3.6.1.4.1.21317.1.3.2.2.3.4.6.4	IpAddress	read-write	Display or set gateway address
INT staticDNSEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.6.5	INTEGER	read-write	Display or set DNS address automatically or not
IP dnsPreferIPv4	1.3.6.1.4.1.21317.1.3.2.2.3.4.6.6	IpAddress	read-write	Display or set prefer DNS address
IP dnsAlternateIPv4	1.3.6.1.4.1.21317.1.3.2.2.3.4.6.7	IpAddress	read-write	Display or set alternate DNS address
eventNotification	1.3.6.1.4.1.21317.1.3.2.2.3.4.7
devicesnmp	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1
INT trapEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.1	INTEGER	read-write	Indicates if this trap entry is enabled or not. You should set the username/auth-password/priv-password first, when choosing snmpv3. You should set the community string first, when choosing snmpv1/v2c.
INT trapVersion	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.2	INTEGER	read-write	Choose SNMP Trap version to send trap. You should set the username/auth-password/priv-password first, when choosing snmpv3. You should set the community string first, when choosing snmpv1/v2c.
snmpTrapTable	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3		not-accessible	PE SNMP agent trap setup table. If users want to use trap, they must set enable trap, ip and community first.
snmpTrapEntry	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1		not-accessible	Single trap entry containing trap receiver info.
INT trapReceiverNumber	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.1	INTEGER	read-only	Index of trap receiver
IP trapReceiverIPAddress	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.2	IpAddress	read-write	Trap receiver IP address
INT trapPort	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.3	INTEGER	read-write	NMS trap port to be used by agent to send trap
STR trapCommunity	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.4	DisplayString	read-write	If use SNMPv1/v2c to receive trap should set this Community string. MAX string length: 20 NOTE: Input string as /empty to set this object to NULL.
STR trapUsername	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.5	DisplayString	read-write	If use SNMPv3 to receive trap should set this string. NOTE: Input string as /empty to set this object to NULL. MAX string length: 20
STR trapAuthpassword	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.6	DisplayString	read-write	If use SNMPv3 to receive trap should set this string. MAX string length: 20 NOTE: Input string as /empty to set this object to NULL.
STR trapPrivpassword	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.7	DisplayString	read-write	If use SNMPv3 to receive trap should set this string. MAX string length: 20 NOTE: Input string as /empty to set this object to NULL.
syslog	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2
INT sysLogServerEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2.1	INTEGER	read-write	Display or set syslog server address automatically or not
IP sysLogServerIPv4	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2.2	IpAddress	read-write	Display or set syslog server address
INT sysLogServerPort	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2.3	INTEGER	read-write	Display or set syslog server port
smtp	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3
INT smtpServerEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.1	INTEGER	read-write	Display or set SMTP server enable status.
STR smtpServerName	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.2	DisplayString	read-write	Display or set a SMTP server name. NOTE: Input string as /empty to set this object to NULL.
INT smtpAuthEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.3	INTEGER	read-write	Display or set authentication of SMTP server.
STR smtpAccountName	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.4	DisplayString	read-write	Display or set a user's name of SMTP server. NOTE: Input string as /empty to set this object to NULL.
STR smtpAccountPwd	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.5	DisplayString	read-write	Display or set a user's password of SMTP server. NOTE: Input string as /empty to set this object to NULL.
STR smtpMailFrom	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.6	DisplayString	read-write	Display or set a mail of SMTP server. NOTE: Input string as /empty to set this object to NULL.
STR smtpMailTo	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.7	DisplayString	read-write	Display or set a mail of SMTP server. NOTE: Input string as /empty to set this object to NULL.
configurationNotification	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.9
INT configurationNotifyEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.9.1	INTEGER	read-write
NTF configurationNotifyTrapMSG	1.3.6.1.4.1.21317.1.3.2.2.3.4.7.9.2
dateTime	1.3.6.1.4.1.21317.1.3.2.2.3.4.8
timeZone	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.1
INT timeZoneSetting	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.1.1	INTEGER	read-write	Display or set the time zone of PE device. (0) [GMT-12:00] Eniwetok Kwajalein (1) [GMT-11:00] Midway Island Samoa (2) [GMT-10:00] Hawaii (3) [GMT-09:00] Alaska (4) [GMT-08:00] Pacific Time (US & Canada); Tijuana (5) [GMT-07:00] Mountain Time (US & Canada) (6) [GMT-07:00] Arizona (7) [GMT-06:00] Central Time (US & Canada) (8) [GMT-06:00] Mexico City (9) [GMT-06:00] Saskatchewan (10)[GMT-06:00] Central America (11)[GMT-05:00] Eastern Time (US & Canada) (12)[GMT-05:00] Indiana (East) (13)[GMT-05:00] Bogota Lima Quito (14)[GMT-04:00] Atlantic Time (Canada) (15)[GMT-04:00] Caracas La Paz (16)[GMT-04:00] Santiago (17)[GMT-03:30] Newfoundland (18)[GMT-03:00] Buenos Aires Georgetown (19)[GMT-03:00] Brasilia (20)[GMT-03:00] Greenland (21)[GMT-02:00] Mid-Atlantic (22)[GMT-01:00] Azores (23)[GMT-01:00] Cape Verde Is (24)[GMT] Casablanca Monrovia (25)[GMT] Greenwich Mean Time: Dublin Edinburgh Lisbon London (26)[GMT+01:00] Amsterdam Copenhagen Madrid Paris Vilnius (27)[GMT+01:00] West Central Africa (28)[GMT+01:00] Belgrade Sarajevo Skopje Sofija Zagreb (29)[GMT+01:00] Bratislava Budapest Ljubljana Prague Warsaw (30)[GMT+01:00] Brussels Berlin Bern Rome Stockholm Vienna (31)[GMT+02:00] Cairo (32)[GMT+02:00] Harare Pretoria (33)[GMT+02:00] Jerusalem (34)[GMT+02:00] Bucharest (35)[GMT+02:00] Helsinki Riga Tallinn (36)[GMT+02:00] Athens Istanbul Minsk (37)[GMT+03:00] Kuwait Riyadh (38)[GMT+03:00] Nairobi (39)[GMT+03:00] Baghdad (40)[GMT+03:00] Moscow St. Petersburg Volgograd (41)[GMT+03:30] Tehran (42)[GMT+04:00] Abu Dhabi Muscat (43)[GMT+04:00] Baku Tbilisi Yerevan (44)[GMT+04:30] Kabul (45)[GMT+05:00] Islamabad Karachi Tashkent (46)[GMT+05:00] Ekaterinburg (47)[GMT+05:30] Calcutta Chennai Mumbai New Delhi (48)[GMT+05:45] Kathmandu (49)[GMT+06:00] Astana Dhaka (50)[GMT+06:00] Sri Jayawardenepura (51)[GMT+06:00] Almaty Novosibirsk (52)[GMT+06:30] Rangoon (53)[GMT+07:00] Bangkok Hanoi Jakarta (54)[GMT+07:00] Krasnoyarsk (55)[GMT+08:00] Beijing Chongqing Hong Kong Urumqi (56)[GMT+08:00] Perth (57)[GMT+08:00] Kuala Lumpur Singapore (58)[GMT+08:00] Taipei (59)[GMT+08:00] Irkutsk Ulaan Bataar (60)[GMT+09:00] Osaka Sapporo Tokyo (61)[GMT+09:00] Seoul (62)[GMT+09:00] Yakutsk (63)[GMT+09:30] Darwin (64)[GMT+09:30] Adelaide (65)[GMT+10:00] Canberra Melbourne Sydney (66)[GMT+10:00] Brisbane (67)[GMT+10:00] Guam Port Moresby (68)[GMT+10:00] Hobart (69)[GMT+10:00] Vladivostok (70)[GMT+11:00] Magadan Solomon Is New Caledonia (71)[GMT+12:00] Fiji Kamchatka Marshall Is. (72)[GMT+12:00] Auckland Wellington (73)[GMT+13:00] Nuku'alofa
INT dstEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.1.2	INTEGER	read-write	Display or set daylight savings time .
manualInput	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.2
STR dateSetting	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.2.1	DisplayString	read-write	Display or set date in a manual way.(This is Greenwich Mean Time, GMT) string length: 10 This value format must match the following form: YYYY-MM-DD ex. 2011-01-01 Note: range of year: 2000-2099 range of month: 01-12 range of day: 01-31
STR timeSetting	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.2.2	DisplayString	read-write	Display or set time in a manual way.(This is Greenwich Mean Time, GMT) string length: 8 This value format must match the following form: HH:MM:SS ex. 02:02:02 Note: range of hour: 00-24 range of minute: 00-60 range of second: 00-60
networkTime	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3
INT autoAdjustEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.1	INTEGER	read-write	Display or set date time useing auto adjustment way.
INT preferNTP	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.2	INTEGER	read-write	Display or set prefer NTP server. AU \| ntp1.cs.mu.OZ.AU(0), AU \| ntp0.cs.mu.OZ.AU(1), BE \| ntp2.oma.be(2), BE \| ntp1.oma.be(3), BR \| ntps1.pads.ufrj.br(4), CH \| swisstime.ethz.ch(5), CL \| ntp.shoa.cl(6), CZ \| ntp.nic.cz(7), DE \| ntp.stairweb.de(8), DE \| ntps1-0.cs.tu-berlin.de(9), DE \| ptbtime1.ptb.de(10), DE \| ntp1.fau.de(11), DE \| ptbtime2.ptb.de(12), DE \| time1.one4vision.de(13), DE \| rustime01.rus.uni-stuttgart.de(14), DE \| ntp.probe-networks.de(15), DE \| ntp2.fau.de(16), ES \| hora.roa.es(17), HK \| stdtime.gov.hk(18), IE \| ntp-galway.hea.net(19), IT \| ntp1.inrim.it(20), IT \| ntp2.inrim.it(21), JP \| clock.tl.fukuoka-u.ac.jp(22), JP \| ntp.nict.jp(23), JP \| clock.nc.fukuoka-u.ac.jp(24), KR \| ntp.xbsd.kr(25), MX \| cronos.cenam.mx(26), NL \| ntp0.nl.uu.net(27), NL \| ntp1.nl.uu.net(28), NL \| ntp.remco.org(29), NL \| ntp0.nl.net(30), PL \| vega.cbk.poznan.pl(31), PL \| ntp.ntp-servers.com(32), RO \| ntp3.usv.ro(33), RO \| ntp2.usv.ro(34), RU \| ntp1.vniiftri.ru; ntp1.imvp.ru(35), RU \| ntp2.vniiftri.ru; ntp2.imvp.ru(36), SE \| ntp1.mmo.netnod.se(37), SE \| ntp1.sth.netnod.se(38), SE \| ntp2.mmo.netnod.se(39), SE \| ntp2.sth.netnod.se(40), SE \| time2.stupi.se(41), SE \| ntp1.sp.se(42), SE \| timehost.lysator.liu.se(43), SI \| ntp.mostovna.com(44), US CA \| timekeeper.isi.edu(45), US CA \| clock.sjc.he.net(46), US CA \| nist1.symmetricom.com(47), US CA \| clock.via.net(48), US CA \| nist1.aol-ca.truetime.com(49), US CA \| clock.isc.org(50), US CA \| clepsydra.dec.com(51), US CA \| gps.layer42.net(52), US CA \| time.no-such-agency.net(53), US CA \| nist1-sj.WiTime.net(54), US CA \| clock.fmt.he.net(55), US CO \| time-b.timefreq.bldrdoc.gov(56), US CO \| time-a.timefreq.bldrdoc.gov(57), US CO \| utcnist.colorado.edu(58), US CO \| time-c.timefreq.bldrdoc.gov(59), US DE \| rackety.udel.edu(60), US DE \| mizbeaver.udel.edu(61), US GA \| nist1.columbiacountyga.gov(62), US IL \| ntp.your.org(63), US MA \| bonehed.lcs.mit.edu(64), US MA \| time.keneli.org(65), US MA \| ntp0.broad.mit.edu(66), US MD \| time-a.nist.gov(67), US MD \| time-b.nist.gov(68), US MI \| nist.netservicesgroup.com(69), US NY \| nist1-ny.WiTime.net(70), US NY \| clock.nyc.he.net(71), US UT \| time.xmission.com(72), US VA \| nist1-dc.WiTime.net(73), US VA \| nist1.aol-va.truetime.com(74), US WA \| time-nw.nist.gov(75), FR \| utp.univ-lyon1.fr(76), FR \| ntp-sop.inria.fr(77), FR \| ntp.tuxfamily.net(78), UK \| bear.zoo.bt.co.uk(79)
INT preferServerIPenable	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.3	INTEGER	read-write	Enable or disable prefer custom server IP.
IP preferNTPIp	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.4	IpAddress	read-write	Display or set prefer NTP server IP.
INT alternateNtpEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.5	INTEGER	read-write	Display or set date time using alternate NTP server.
INT alternateNtp	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.6	INTEGER	read-write	Display or set alternative NTP server. AU \| ntp1.cs.mu.OZ.AU(0), AU \| ntp0.cs.mu.OZ.AU(1), BE \| ntp2.oma.be(2), BE \| ntp1.oma.be(3), BR \| ntps1.pads.ufrj.br(4), CH \| swisstime.ethz.ch(5), CL \| ntp.shoa.cl(6), CZ \| ntp.nic.cz(7), DE \| ntp.stairweb.de(8), DE \| ntps1-0.cs.tu-berlin.de(9), DE \| ptbtime1.ptb.de(10), DE \| ntp1.fau.de(11), DE \| ptbtime2.ptb.de(12), DE \| time1.one4vision.de(13), DE \| rustime01.rus.uni-stuttgart.de(14), DE \| ntp.probe-networks.de(15), DE \| ntp2.fau.de(16), ES \| hora.roa.es(17), HK \| stdtime.gov.hk(18), IE \| ntp-galway.hea.net(19), IT \| ntp1.inrim.it(20), IT \| ntp2.inrim.it(21), JP \| clock.tl.fukuoka-u.ac.jp(22), JP \| ntp.nict.jp(23), JP \| clock.nc.fukuoka-u.ac.jp(24), KR \| ntp.xbsd.kr(25), MX \| cronos.cenam.mx(26), NL \| ntp0.nl.uu.net(27), NL \| ntp1.nl.uu.net(28), NL \| ntp.remco.org(29), NL \| ntp0.nl.net(30), PL \| vega.cbk.poznan.pl(31), PL \| ntp.ntp-servers.com(32), RO \| ntp3.usv.ro(33), RO \| ntp2.usv.ro(34), RU \| ntp1.vniiftri.ru; ntp1.imvp.ru(35), RU \| ntp2.vniiftri.ru; ntp2.imvp.ru(36), SE \| ntp1.mmo.netnod.se(37), SE \| ntp1.sth.netnod.se(38), SE \| ntp2.mmo.netnod.se(39), SE \| ntp2.sth.netnod.se(40), SE \| time2.stupi.se(41), SE \| ntp1.sp.se(42), SE \| timehost.lysator.liu.se(43), SI \| ntp.mostovna.com(44), US CA \| timekeeper.isi.edu(45), US CA \| clock.sjc.he.net(46), US CA \| nist1.symmetricom.com(47), US CA \| clock.via.net(48), US CA \| nist1.aol-ca.truetime.com(49), US CA \| clock.isc.org(50), US CA \| clepsydra.dec.com(51), US CA \| gps.layer42.net(52), US CA \| time.no-such-agency.net(53), US CA \| nist1-sj.WiTime.net(54), US CA \| clock.fmt.he.net(55), US CO \| time-b.timefreq.bldrdoc.gov(56), US CO \| time-a.timefreq.bldrdoc.gov(57), US CO \| utcnist.colorado.edu(58), US CO \| time-c.timefreq.bldrdoc.gov(59), US DE \| rackety.udel.edu(60), US DE \| mizbeaver.udel.edu(61), US GA \| nist1.columbiacountyga.gov(62), US IL \| ntp.your.org(63), US MA \| bonehed.lcs.mit.edu(64), US MA \| time.keneli.org(65), US MA \| ntp0.broad.mit.edu(66), US MD \| time-a.nist.gov(67), US MD \| time-b.nist.gov(68), US MI \| nist.netservicesgroup.com(69), US NY \| nist1-ny.WiTime.net(70), US NY \| clock.nyc.he.net(71), US UT \| time.xmission.com(72), US VA \| nist1-dc.WiTime.net(73), US VA \| nist1.aol-va.truetime.com(74), US WA \| time-nw.nist.gov(75), FR \| utp.univ-lyon1.fr(76), FR \| ntp-sop.inria.fr(77), FR \| ntp.tuxfamily.net(78), UK \| bear.zoo.bt.co.uk(79)
INT alternateServerIPenable	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.7	INTEGER	read-write	Enable or disable alternate custom server IP.
IP alternateNtpIp	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.8	IpAddress	read-write	Display or set alternative NTP server IP.
INT adjustTimeEveryDays	1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.9	INTEGER	read-write	Display or set frequency of adjustment in days.
devicesecurity	1.3.6.1.4.1.21317.1.3.2.2.3.5
loginFailures	1.3.6.1.4.1.21317.1.3.2.2.3.5.1
INT loginAllowTimes	1.3.6.1.4.1.21317.1.3.2.2.3.5.1.1	INTEGER	read-write	Display or set time of login faliure.
INT loginTimeOut	1.3.6.1.4.1.21317.1.3.2.2.3.5.1.2	INTEGER	read-write	Display or set login time out.
workingMode	1.3.6.1.4.1.21317.1.3.2.2.3.5.2
INT icmpEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.5.2.1	INTEGER	read-write	Display or set status of ICMP.
accountPolicy	1.3.6.1.4.1.21317.1.3.2.2.3.5.3
INT minUserNameLen	1.3.6.1.4.1.21317.1.3.2.2.3.5.3.1	INTEGER	read-write	Display or set minimum length of user name.
INT minUserPwdLen	1.3.6.1.4.1.21317.1.3.2.2.3.5.3.2	INTEGER	read-write	Display or set minimum length of user password.
INT upperCaseEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.5.3.3	INTEGER	read-write	Display or set one upper case rule in user password.
INT lowerCaseEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.5.3.4	INTEGER	read-write	Display or set one lower case rule in user password.
INT numberEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.5.3.5	INTEGER	read-write	Display or set one number rule in user password.
INT disableDuplicateLogin	1.3.6.1.4.1.21317.1.3.2.2.3.5.3.6	INTEGER	read-write	Display or set status of disabled duplicate login rule.
loginRestriction	1.3.6.1.4.1.21317.1.3.2.2.3.5.4
STR loginString	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.1	DisplayString	read-write	Display or set a login string. string length: 0~32 NOTE: Input string as /empty to set this object to NULL.
ipFilter	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2
INT ipFilterEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.1	INTEGER	read-write	Display or set status of ip filter.
INT ipFilterRule	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.2	INTEGER	read-write	Display or set status of ip filter rule.
ipFilterTable	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3		not-accessible	A list of restricted ip.
ipFilterEntry	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1		not-accessible	Status and parameter values for a PE's restricted IP.
INT ipFilterIndex	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1.1	INTEGER	read-only	The value of index for the ip filter.
IP ipFilterFrom	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1.2	IpAddress	read-write	A set of restricted ip. ex. 192.168.0.1 Note: Users must follow in order to set the ip address. Note: To clear the settings to set the ip 0.0.0.0
IP ipFilterTo	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1.3	IpAddress	read-write	A set of restricted ip. ex. 192.168.0.255 Note: Users must follow in order to set the ip address. Note: To clear the settings to set the ip 0.0.0.0
macFilter	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3
INT macFilterEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.1	INTEGER	read-write	Display or set status of mac filter.
INT macFilterRule	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.2	INTEGER	read-write	Display or set status of mac filter rule.
macFilterTable	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3		not-accessible	A list of restricted mac.
macFilterEntry	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3.1		not-accessible	Status and parameter values for a PE's restricted MAC.
INT macFilterIndex	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3.1.1	INTEGER	read-only	The value of index for the mac filter.
STR macFilterSet	1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3.1.2	DisplayString	read-write	A set of restricted mac. string length: 12 ex. 004854655511 Note: Users must follow in order to set the MAC address. Note: To clear the settings to set the MAC 000000000000
authentication	1.3.6.1.4.1.21317.1.3.2.2.3.5.5
radius	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1
INT radiusEnabled	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.1	INTEGER	read-write	Display or set status of RADIUS server.
IP preferRadiusIp	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.2	IpAddress	read-write	Display or set prefer RADIUS server IP.
INT preferRadiusPort	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.3	INTEGER	read-write	Display or set prefer RADIUS server port.
IP alternateRadiusIp	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.4	IpAddress	read-write	Display or set alternative RADIUS server IP.
INT alternateRadiusPort	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.5	INTEGER	read-write	Display or set alternative RADIUS server port.
INT radiusTimeOut	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.6	INTEGER	read-write	Display or set time out of authentication using RADIUS server. The unit is sec.
INT radiusRetry	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.7	INTEGER	read-write	Display or set retry times of authentication using RADIUS server.
STR radiusSecret	1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.8	DisplayString	read-write	Display or set shared secret of RADIUS server. string length: 6~15 At least 6 characters. NOTE: Input string as /empty to set this object to NULL.
NTF customTrapMSG	1.3.6.1.4.1.21317.1.3.2.2.5			Display custom trap message.
INT rebootDevice	1.3.6.1.4.1.21317.1.3.2.2.6	INTEGER	read-write	Reboot PE Device

RFC description

ATEN International vendor-private MIB for PE series Power over IP management, configuration, sensors, and CAP features.

Start monitoring ATEN PE-series intelligent PDUs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ATEN-PE-CFG-STR

What Is ATEN-PE-CFG-STR?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description