AIRESPACE-SWITCHING-MIB

All MIBs › AIRESPACE-SWITCHING-MIB

Organization: Airespace, Inc.

Last Updated: 2006-04-10

Category: VLAN and Bridging, Wireless and WLAN

Description: Manages switching configuration and VLAN membership on Airespace (Cisco) wireless LAN controllers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AIRESPACE-SWITCHING-MIB?

AIRESPACE-SWITCHING-MIB is a MIB originally from Airespace (acquired by Cisco) for wireless LAN controllers acting as Central Controllers that terminate the LWAPP tunnel from lightweight access points. It covers switching-layer configuration such as VLAN membership/quarantine settings and per-port switching statistics, alongside the controller's broader role of exposing inventory, memory, CPU, and trap-log information as described in its module text. For hardware/software status monitoring, it supports checking controller CPU and memory load, inventory/hardware identification, and trap history, in addition to port-level switching statistics that reveal traffic anomalies. It is tied to the LWAPP architecture and complements companion Airespace/Cisco wireless MIBs covering AP and radio status. It is deployed on Airespace/Cisco wireless LAN controllers (the predecessor to Cisco's Unified Wireless Network controllers) managing fleets of lightweight access points, and the AIRESPACE-SWITCHING-MIB MIB Browser view lets administrators inspect these switching-layer objects directly.

IPNetwork Monitor allows you to monitor SNMP objects defined in AIRESPACE-SWITCHING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Airespace/Cisco wireless LAN controller

Monitoring Examples

An administrator would check agentInterfaceVlanQuarantine to confirm which VLAN is used to quarantine a management interface or misbehaving client traffic, and poll portStatsTable/portStatsEntry to review per-port switching statistics on the controller's physical uplink/downlink ports for error or utilization anomalies. Because the module description also references controller memory, CPU, and trap logs, an admin would correlate port-level stats with overall controller resource load when diagnosing wireless performance issues.

What Can Be Monitored

VLAN quarantine configuration
per-port switching statistics
controller CPU load
controller memory usage
controller inventory
trap log history

Imported Objects

From AIRESPACE-REF-MIB

airespace

MODULE-IDENTITY

From IANAifType-MIB

IANAifType

From Q-BRIDGE-MIB

dot1qFdbId	OBJECT-TYPE
dot1qVlanIndex	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
PhysAddress
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using portStatsPktsTx64Octets OID:

Select a Cisco (Airespace) Wireless LAN Controller (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type portStatsPktsTx64Octets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of packets (including bad packets) transmitted that were 64 octets in length (excluding framing bits but including FCS octets). On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in Packets), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
I32 agentApAssociateDisassociateTrapCount	1.3.6.1.4.1.14179.1.1.2.6	Integer32	read-only	The total number of AP Associate/Disassociate traps sent since last reset.
I32 agentApCoverageProfileFailTrapCount	1.3.6.1.4.1.14179.1.1.2.10	Integer32	read-only	The total number of AP Coverge Profile Failure traps sent since last reset.
I32 agentApInterferenceProfileFailTrapCount	1.3.6.1.4.1.14179.1.1.2.9	Integer32	read-only	The total number of AP Interference Profile Failure traps sent since last reset.
I32 agentApLoadProfileFailTrapCount	1.3.6.1.4.1.14179.1.1.2.7	Integer32	read-only	The total number of AP Load Profile Failure traps sent since last reset.
I32 agentApNoiseProfileFailTrapCount	1.3.6.1.4.1.14179.1.1.2.8	Integer32	read-only	The total number of AP Noise Profile Failure traps sent since last reset.
INT agentClearConfig	1.3.6.1.4.1.14179.1.3.2	INTEGER	read-write	clear config to factory defaults
INT agentClearLags	1.3.6.1.4.1.14179.1.3.3	INTEGER	read-write	clear lag configuration
INT agentClearLoginSessions	1.3.6.1.4.1.14179.1.3.4	INTEGER	read-write	close all telnet sessions
INT agentClearPortStats	1.3.6.1.4.1.14179.1.3.6	INTEGER	read-write	clear all port statistics
INT agentClearSwitchStats	1.3.6.1.4.1.14179.1.3.7	INTEGER	read-write	clear all switch statistics
INT agentClearTrapLog	1.3.6.1.4.1.14179.1.3.8	INTEGER	read-write	clear trap log
agentCLIConfigGroup	1.3.6.1.4.1.14179.1.2.1
agentConfigGroup	1.3.6.1.4.1.14179.1.2
INT agentCurrentCPUUtilization	1.3.6.1.4.1.14179.1.1.5.1	INTEGER	read-only	Current CPU Load of the switch in percentage.
agentDhcpConfigGroup	1.3.6.1.4.1.14179.1.2.15
IP agentDhcpScopeDefaultRouterAddress1	1.3.6.1.4.1.14179.1.2.15.1.1.8	IpAddress	read-create	IP Address of the DHCP Scope's default Router 1.
IP agentDhcpScopeDefaultRouterAddress2	1.3.6.1.4.1.14179.1.2.15.1.1.9	IpAddress	read-create	IP Address of the DHCP Scope's default Router 2.
IP agentDhcpScopeDefaultRouterAddress3	1.3.6.1.4.1.14179.1.2.15.1.1.10	IpAddress	read-create	IP Address of the DHCP Scope's default Router 3.
STR agentDhcpScopeDnsDomainName	1.3.6.1.4.1.14179.1.2.15.1.1.11	DisplayString	read-create	DNS Domain name for the DHCP Scope.
IP agentDhcpScopeDnsServerAddress1	1.3.6.1.4.1.14179.1.2.15.1.1.12	IpAddress	read-create	IP Address of the DHCP Scope's DNS Server 1.
IP agentDhcpScopeDnsServerAddress2	1.3.6.1.4.1.14179.1.2.15.1.1.13	IpAddress	read-create	IP Address of the DHCP Scope's DNS Server 2.
IP agentDhcpScopeDnsServerAddress3	1.3.6.1.4.1.14179.1.2.15.1.1.14	IpAddress	read-create	IP Address of the DHCP Scope's DNS Server 3.
agentDhcpScopeEntry	1.3.6.1.4.1.14179.1.2.15.1.1		not-accessible	Switch's DHCP Server Scope entry.
U32 agentDhcpScopeIndex	1.3.6.1.4.1.14179.1.2.15.1.1.1	Unsigned32	read-create	DHCP Scope Identifier Index.
I32 agentDhcpScopeLeaseTime	1.3.6.1.4.1.14179.1.2.15.1.1.3	Integer32	read-create	DHCP Scope Lease time in seconds.
STR agentDhcpScopeName	1.3.6.1.4.1.14179.1.2.15.1.1.2	DisplayString	read-create	DHCP Scope Name.
IP agentDhcpScopeNetbiosNameServerAddress1	1.3.6.1.4.1.14179.1.2.15.1.1.15	IpAddress	read-create	IP Address of DHCP Scope's Netbios Name Server 1.
IP agentDhcpScopeNetbiosNameServerAddress2	1.3.6.1.4.1.14179.1.2.15.1.1.16	IpAddress	read-create	IP Address of DHCP Scope's Netbios Name Server 2.
IP agentDhcpScopeNetbiosNameServerAddress3	1.3.6.1.4.1.14179.1.2.15.1.1.17	IpAddress	read-create	IP Address of DHCP Scope's Netbios Name Server 3.
IP agentDhcpScopeNetmask	1.3.6.1.4.1.14179.1.2.15.1.1.5	IpAddress	read-create	The DHCP Scope Netmask. This the subnet mask for the address pool.
IP agentDhcpScopeNetwork	1.3.6.1.4.1.14179.1.2.15.1.1.4	IpAddress	read-create	IP Address of the DHCP Scope Network. This is the address which is used to determine the DHCP scope a remote Switch is attaching to.
IP agentDhcpScopePoolEndAddress	1.3.6.1.4.1.14179.1.2.15.1.1.7	IpAddress	read-create	The DHCP Scope address pool end IP address.
IP agentDhcpScopePoolStartAddress	1.3.6.1.4.1.14179.1.2.15.1.1.6	IpAddress	read-create	The DHCP Scope address pool start IP address.
ROW agentDhcpScopeRowStatus	1.3.6.1.4.1.14179.1.2.15.1.1.30	RowStatus	read-create	Dhcp Scope entry row status.
INT agentDhcpScopeState	1.3.6.1.4.1.14179.1.2.15.1.1.18	INTEGER	read-create	DHCP Scope's State.
agentDhcpScopeTable	1.3.6.1.4.1.14179.1.2.15.1		not-accessible	A table listing the Scopes defined on the switch's DHCP Server.
I32 agentDot3adAggPort	1.3.6.1.4.1.14179.1.2.11.1.1	Integer32	read-only	ifIndex of this physical port
agentDot3adAggPortEntry	1.3.6.1.4.1.14179.1.2.11.1		not-accessible	Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.
INT agentDot3adAggPortLACPMode	1.3.6.1.4.1.14179.1.2.11.1.21	INTEGER	read-write	Enable/disable 802.3ad LACP on this port
agentDot3adAggPortTable	1.3.6.1.4.1.14179.1.2.11		not-accessible	This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.
I32 agentFreeMemory	1.3.6.1.4.1.14179.1.1.5.3	Integer32	read-only	Free RAM of the switch in Kbytes.
agentInfoGroup	1.3.6.1.4.1.14179.1.1
STR agentInterfaceAclName	1.3.6.1.4.1.14179.1.2.13.1.13	DisplayString	read-create	Name of the Access Control List applied to the interface. This attribute is applicable only to the management interface and other dynamic interfaces. If it is required to remove the ACL name for an interface, it should be set to an empty string.
I32 agentInterfaceActivePortNo	1.3.6.1.4.1.14179.1.2.13.1.15	Integer32	read-only	This is the currently active port for this interface.
INT agentInterfaceAPManagementFeature	1.3.6.1.4.1.14179.1.2.13.1.14	INTEGER	read-create	When enabled, the dynamic interface can be used for AP management. SNMP support for AP management through dynamic interfaces has been introduced since '3.0.21.0' release. Only applicable to dynamic interfaces in 4200 series. In static interfaces, 'disable' value 0 is returned. In 4000/3500 series of switches, 'disable' value 0 is returned.
I32 agentInterfaceBackupPortNo	1.3.6.1.4.1.14179.1.2.13.1.16	Integer32	read-create	This values is valid only for the 4200 series of switches. The backup port is the port this interface is moved to once the primary port fails. A value 0 means the port is not set. The valid value can be any one of the physical ports on the 4200 switch.
agentInterfaceConfigEntry	1.3.6.1.4.1.14179.1.2.13.1		not-accessible	Switch's Interface Config entry
agentInterfaceConfigTable	1.3.6.1.4.1.14179.1.2.13		not-accessible	A table of the switch's Interface Config entries Typically, it will contain entries for Service Port Interface, DS Port Interface and Virtual Gateway Interface apart from other entries.
INT agentInterfaceDhcpProtocol	1.3.6.1.4.1.14179.1.2.13.1.11	INTEGER	read-create	The interface's DHCP protocol. This applies only to the service port interface.
STR agentInterfaceDnsHostName	1.3.6.1.4.1.14179.1.2.13.1.12	DisplayString	read-create	The DNS host name for the Virtual Interface. This attribute is not valid for other interfaces.
IP agentInterfaceIPAddress	1.3.6.1.4.1.14179.1.2.13.1.5	IpAddress	read-create	IP Address of the interface.
IP agentInterfaceIPGateway	1.3.6.1.4.1.14179.1.2.13.1.7	IpAddress	read-create	IP Gateway of the interface. This is 0 for virtual and service-port interface.
IP agentInterfaceIPNetmask	1.3.6.1.4.1.14179.1.2.13.1.6	IpAddress	read-create	IP Netmask of the interface. This is 0 for the virtual interface.
MAC agentInterfaceMacAddress	1.3.6.1.4.1.14179.1.2.13.1.4	MacAddress	read-only	Interface MAC Address. This is only applicable in case of management and service-port interfaces.
OCT agentInterfaceName	1.3.6.1.4.1.14179.1.2.13.1.1	OCTET STRING	read-create	Interace Name. This values is 'management' for DS port, 'service-port' for service port and 'virtual' for virtual gateway. For other interfaces, the name can be anything. These interfaces are already created by default.
I32 agentInterfacePortNo	1.3.6.1.4.1.14179.1.2.13.1.8	Integer32	read-create	A value 0 means the port is not set. The valid value can be any one of the physical ports on the switch. This is the primary port configured on the interface.
IP agentInterfacePrimaryDhcpAddress	1.3.6.1.4.1.14179.1.2.13.1.9	IpAddress	read-create	Primary DHCP Server IP Address for the interface This applies to the management interface and other dynamic interfaces.
ROW agentInterfaceRowStatus	1.3.6.1.4.1.14179.1.2.13.1.31	RowStatus	read-create	The interface entry Row status.
IP agentInterfaceSecondaryDhcpAddress	1.3.6.1.4.1.14179.1.2.13.1.10	IpAddress	read-create	Secondary DHCP Server IP Address for the interface. This applies to the management interface and other dynamic interfaces.
INT agentInterfaceType	1.3.6.1.4.1.14179.1.2.13.1.3	INTEGER	read-only	The interface's type. The static type is set for the interfaces that are created by default on the switch and these cannot be deleted. Any other interface that is created is of type dynamic which can be deleted.
I32 agentInterfaceVlanId	1.3.6.1.4.1.14179.1.2.13.1.2	Integer32	read-create	Vlan ID configured for the Interface.
T/F agentInterfaceVlanQuarantine	1.3.6.1.4.1.14179.1.2.13.1.17	TruthValue	read-create	This object is used to configure the health of the interface identified by agentInterfaceName. A value of 'true' is used to indicate that this particular interface is unhealthy. In this case, the data packets of the clients, that are assigned the VLAN Id corresponding to this interface, must be tunneled to the Controller by the REAP AP. A value of 'false' indicates that the VLAN configured against the interface is healthy and that the REAP AP can switch the clients of this VLAN locally rather than tunneling them to the Controller.
PHY agentInventoryBurnedInMacAddress	1.3.6.1.4.1.14179.1.1.1.9	PhysAddress	read-only	Burned-In MAC Address
T/F agentInventoryFipsModeEnabled	1.3.6.1.4.1.14179.1.1.1.20	TruthValue	read-only	True if FIPS (Federal Information Processing Standards) mode has been enabled on the controller.False if FIPS mode has not been enabled. FIPS mode can only be enabled through console.
agentInventoryGroup	1.3.6.1.4.1.14179.1.1.1
T/F agentInventoryIsCryptoCard2Present	1.3.6.1.4.1.14179.1.1.1.19	TruthValue	read-only	True if the switch is carrying second Crypto card for 4400 controller.
T/F agentInventoryIsCryptoCardPresent	1.3.6.1.4.1.14179.1.1.1.16	TruthValue	read-only	True if the switch is carrying a Crypto card.
T/F agentInventoryIsForeignAPSupported	1.3.6.1.4.1.14179.1.1.1.17	TruthValue	read-only	States whether the switch supports third party Access Points.
T/F agentInventoryIsGigECardPresent	1.3.6.1.4.1.14179.1.1.1.15	TruthValue	read-only	True if the Switch contains a Gigabit ethernet card .
STR agentInventoryMachineModel	1.3.6.1.4.1.14179.1.1.1.3	DisplayString	read-only	The switch's Machine Model.
STR agentInventoryMachineType	1.3.6.1.4.1.14179.1.1.1.2	DisplayString	read-only	Type of the Machine used in the Switch.
STR agentInventoryMaintenanceLevel	1.3.6.1.4.1.14179.1.1.1.6	DisplayString	read-only	The switch's Inventory Maintenance Level
STR agentInventoryManufacturerName	1.3.6.1.4.1.14179.1.1.1.12	DisplayString	read-only	Name of the switch manufacturer.
I32 agentInventoryMaxNumberOfAPsSupported	1.3.6.1.4.1.14179.1.1.1.18	Integer32	read-only	Maximum number of APs supported with this Controller.
STR agentInventoryOperatingSystem	1.3.6.1.4.1.14179.1.1.1.10	DisplayString	read-only	Operating System running on this unit
STR agentInventoryProductName	1.3.6.1.4.1.14179.1.1.1.13	DisplayString	read-only	Name of the product.
STR agentInventoryProductVersion	1.3.6.1.4.1.14179.1.1.1.14	DisplayString	read-only	Version of the product.
STR agentInventorySerialNumber	1.3.6.1.4.1.14179.1.1.1.4	DisplayString	read-only	Serial number of the switch.
STR agentInventorySysDescription	1.3.6.1.4.1.14179.1.1.1.1	DisplayString	read-only	The switch's Inventory system description.
STR agentLagConfigCreate	1.3.6.1.4.1.14179.1.2.2.1	DisplayString	read-write	Agent Lag Create. When this object is set with a non-empty string, a new lag will be created.if possible with the entered string as it's name.
agentLagConfigGroup	1.3.6.1.4.1.14179.1.2.2
INT agentLagConfigMode	1.3.6.1.4.1.14179.1.2.2.4	INTEGER	read-write	The Lag Mode on the 4400 series controller. When it is on, all the gigabit ports are bound to one aggregated link.
agentLagDetailedConfigEntry	1.3.6.1.4.1.14179.1.2.2.3.1		not-accessible	Switch's lag config entry
agentLagDetailedConfigTable	1.3.6.1.4.1.14179.1.2.2.3		not-accessible	A detailed table of the switch's lag config entries
I32 agentLagDetailedIfIndex	1.3.6.1.4.1.14179.1.2.2.3.1.2	Integer32	read-only	Lag port index
I32 agentLagDetailedLagIndex	1.3.6.1.4.1.14179.1.2.2.3.1.1	Integer32	read-only	Lag index
OID agentLagDetailedPortSpeed	1.3.6.1.4.1.14179.1.2.2.3.1.22	OBJECT IDENTIFIER	read-only	Lag port speed. See agentPortType for description and list of valid values.
I32 agentLagSummaryAddPort	1.3.6.1.4.1.14179.1.2.2.2.1.7	Integer32	read-create	Agent Lag Add Port. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.
INT agentLagSummaryAdminMode	1.3.6.1.4.1.14179.1.2.2.2.1.5	INTEGER	read-create	Agent Lag Admin Mode
agentLagSummaryConfigEntry	1.3.6.1.4.1.14179.1.2.2.2.1		not-accessible	Switch's lag config entry
agentLagSummaryConfigTable	1.3.6.1.4.1.14179.1.2.2.2		not-accessible	A summary table of the switch's lag config entries
I32 agentLagSummaryDeletePort	1.3.6.1.4.1.14179.1.2.2.2.1.8	Integer32	read-create	Agent Lag Delete Port
I32 agentLagSummaryFlushTimer	1.3.6.1.4.1.14179.1.2.2.2.1.3	Integer32	read-create	Agent Lag Flush Timer
I32 agentLagSummaryLagIndex	1.3.6.1.4.1.14179.1.2.2.2.1.2	Integer32	read-only	Agent Lag If Index
INT agentLagSummaryLinkTrap	1.3.6.1.4.1.14179.1.2.2.2.1.4	INTEGER	read-create	Agent Lag Link Trap
STR agentLagSummaryName	1.3.6.1.4.1.14179.1.2.2.2.1.1	DisplayString	read-create	Agent Lag Name
U32 agentLagSummaryPortsBitMask	1.3.6.1.4.1.14179.1.2.2.2.1.9	Unsigned32	read-create	Agent Lag Member Ports in bit mask representation
ROW agentLagSummaryStatus	1.3.6.1.4.1.14179.1.2.2.2.1.30	RowStatus	read-create	Agent Lag Status. active(1) - This Lag is enabled. destroy(6) - Set to this value to remove the Lag.
INT agentLagSummaryStpMode	1.3.6.1.4.1.14179.1.2.2.2.1.6	INTEGER	read-create	Agent Lag STP Mode
INT agentLoginSessionConnectionType	1.3.6.1.4.1.14179.1.2.1.1.1.4	INTEGER	read-only	Agent Login Session Connection Type of the switch
agentLoginSessionEntry	1.3.6.1.4.1.14179.1.2.1.1.1		not-accessible	Login Session Entry
TIK agentLoginSessionIdleTime	1.3.6.1.4.1.14179.1.2.1.1.1.5	TimeTicks	read-only	Agent Login Session Idle Time of the switch
I32 agentLoginSessionIndex	1.3.6.1.4.1.14179.1.2.1.1.1.1	Integer32	read-only	Agent Login Session Index of the switch
IP agentLoginSessionIPAddress	1.3.6.1.4.1.14179.1.2.1.1.1.3	IpAddress	read-only	Agent Login Session IP Address of the switch
TIK agentLoginSessionSessionTime	1.3.6.1.4.1.14179.1.2.1.1.1.6	TimeTicks	read-only	Agent Login Session Time of the switch
ROW agentLoginSessionStatus	1.3.6.1.4.1.14179.1.2.1.1.1.26	RowStatus	read-write	Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.
agentLoginSessionTable	1.3.6.1.4.1.14179.1.2.1.1		not-accessible	A table of the switch's login session
STR agentLoginSessionUserName	1.3.6.1.4.1.14179.1.2.1.1.1.2	DisplayString	read-only	Agent Login Session UserName of the switch
INT agentNetworkAllowMgmtViaWireless	1.3.6.1.4.1.14179.1.2.3.16	INTEGER	read-write	This states whether Management via wireless is allowed or not.
U32 agentNetworkArpTimeout	1.3.6.1.4.1.14179.1.2.3.13	Unsigned32	read-write	Sets the ARP entry timeout.
INT agentNetworkBroadcastSsidMode	1.3.6.1.4.1.14179.1.2.3.17	INTEGER	read-write	This mode when enabled allows WLAN SSIDs to be broadcasted.
PHY agentNetworkBurnedInMacAddress	1.3.6.1.4.1.14179.1.2.3.4	PhysAddress	read-only	The switch's Burned-In MAC address
agentNetworkConfigGroup	1.3.6.1.4.1.14179.1.2.3
INT agentNetworkConfigProtocol	1.3.6.1.4.1.14179.1.2.3.7	INTEGER	read-write	The switch's network config protocol
IP agentNetworkDefaultGateway	1.3.6.1.4.1.14179.1.2.3.3	IpAddress	read-write	The switch's network default gateway
I32 agentNetworkDsPortNumber	1.3.6.1.4.1.14179.1.2.3.11	Integer32	read-write	The switch's distribution port number.
INT agentNetworkGvrpStatus	1.3.6.1.4.1.14179.1.2.3.15	INTEGER	read-write	The state of GVRP operation on the Switch. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.(Attribute No longer supported)
IP agentNetworkIPAddress	1.3.6.1.4.1.14179.1.2.3.1	IpAddress	read-write	The switch's network ip address
U32 agentNetworkManagementVlan	1.3.6.1.4.1.14179.1.2.3.14	Unsigned32	read-write	VLAN ID of the network management interface.
IP agentNetworkMulticastGroupAddress	1.3.6.1.4.1.14179.1.2.3.25	IpAddress	read-write	Multicast group address for access points.
INT agentNetworkMulticastMode	1.3.6.1.4.1.14179.1.2.3.10	INTEGER	read-write	Switch's ethernet multicast support. disable- multicast is disabled multicast - Multicast is enabled. unicast- Controller will convert multicast to unicast packet.
INT agentNetworkPeerToPeerBlockingMode	1.3.6.1.4.1.14179.1.2.3.24	INTEGER	read-write	Mobile Peer to Peer Blocking mode on the switch.
agentNetworkRouteConfigEntry	1.3.6.1.4.1.14179.1.2.3.23.1		not-accessible	Switch's Network Route entry
agentNetworkRouteConfigTable	1.3.6.1.4.1.14179.1.2.3.23		not-accessible	A table of the switch's Network Route entries
IP agentNetworkRouteGateway	1.3.6.1.4.1.14179.1.2.3.23.1.3	IpAddress	read-create	Network Route IP Gateway.
IP agentNetworkRouteIPAddress	1.3.6.1.4.1.14179.1.2.3.23.1.1	IpAddress	read-create	Network Route IP Address.
IP agentNetworkRouteIPNetmask	1.3.6.1.4.1.14179.1.2.3.23.1.2	IpAddress	read-create	Network Route IP Netmask.
ROW agentNetworkRouteStatus	1.3.6.1.4.1.14179.1.2.3.23.1.23	RowStatus	read-create	Network Route Row Status.
INT agentNetworkSecureWebMode	1.3.6.1.4.1.14179.1.2.3.9	INTEGER	read-write	If https is enable or not provided web mode is enabled
OCT agentNetworkSecureWebPassword	1.3.6.1.4.1.14179.1.2.3.18	OCTET STRING	read-write	SSL Certificate Password. This can be optionally set while downloading SSL certificates of type Web Admin and Web Authentication
IP agentNetworkSubnetMask	1.3.6.1.4.1.14179.1.2.3.2	IpAddress	read-write	The switch's network subnet mask
U32 agentNetworkUserIdleTimeout	1.3.6.1.4.1.14179.1.2.3.12	Unsigned32	read-write	Sets the idle user timeout.
INT agentNetworkWebAdminCertRegenerateCmdInvoke	1.3.6.1.4.1.14179.1.2.3.20	INTEGER	read-write	This command when set to 'activate' will regenerate a Web Administration Certificate Locally that will replace the existing certificate.
STR agentNetworkWebAdminCertType	1.3.6.1.4.1.14179.1.2.3.19	DisplayString	read-only	Type of currently existing Web Admin Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally.
INT agentNetworkWebAuthCertRegenerateCmdInvoke	1.3.6.1.4.1.14179.1.2.3.22	INTEGER	read-write	This command when set to 'activate' will regenerate a Web Authentication Certificate Locally that will replace the existing certificate.
STR agentNetworkWebAuthCertType	1.3.6.1.4.1.14179.1.2.3.21	DisplayString	read-only	Type of currently exisitng Web Authentication Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally.
INT agentNetworkWebMode	1.3.6.1.4.1.14179.1.2.3.8	INTEGER	read-write	The switch's web access mode.
agentNtpConfigGroup	1.3.6.1.4.1.14179.1.2.14
I32 agentNtpPollingInterval	1.3.6.1.4.1.14179.1.2.14.1	Integer32	read-write	Network Time Protocol polling interval. Min value is one hour and maximum is a week.
IP agentNtpServerAddress	1.3.6.1.4.1.14179.1.2.14.2.1.2	IpAddress	read-create	IP Address of the NTP Server
agentNtpServerEntry	1.3.6.1.4.1.14179.1.2.14.2.1		not-accessible	Switch's NTP Server entry. Upto 4 entries may be added.
I32 agentNtpServerIndex	1.3.6.1.4.1.14179.1.2.14.2.1.1	Integer32	read-create	NTP Server priority index.
ROW agentNtpServerRowStatus	1.3.6.1.4.1.14179.1.2.14.2.1.20	RowStatus	read-create	NTP server entry row status.
agentNtpServerTable	1.3.6.1.4.1.14179.1.2.14.2		not-accessible	A summary table for switch's lag config entries
INT agentPortAdminMode	1.3.6.1.4.1.14179.1.2.12.1.6	INTEGER	read-write	The switch's Port Admin Mode
INT agentPortAutoNegAdminStatus	1.3.6.1.4.1.14179.1.2.12.1.13	INTEGER	read-write	This object identifies the administration status of auto negotiation for this port.
INT agentPortClearStats	1.3.6.1.4.1.14179.1.2.12.1.10	INTEGER	read-write	Clear stats for this port only
agentPortConfigEntry	1.3.6.1.4.1.14179.1.2.12.1		not-accessible	Switch's physical port config entry
agentPortConfigTable	1.3.6.1.4.1.14179.1.2.12		not-accessible	A table of the switch's physical port config entries
OID agentPortDefaultType	1.3.6.1.4.1.14179.1.2.12.1.11	OBJECT IDENTIFIER	read-write	This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively- configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
I32 agentPortDot1dBasePort	1.3.6.1.4.1.14179.1.2.12.1.1	Integer32	read-only	The port number of this port.
INT agentPortDot3FlowControlMode	1.3.6.1.4.1.14179.1.2.12.1.14	INTEGER	read-write	Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.
U32 agentPortGarpJoinTime	1.3.6.1.4.1.14179.1.2.12.1.17	Unsigned32	read-write	The GARP Join time, in centiseconds.(Attribute no longer supported)
U32 agentPortGarpLeaveAllTime	1.3.6.1.4.1.14179.1.2.12.1.19	Unsigned32	read-write	The GARP LeaveAll time, in centiseconds.(Attribute no longer supported)
U32 agentPortGarpLeaveTime	1.3.6.1.4.1.14179.1.2.12.1.18	Unsigned32	read-write	The GARP Leave time, in centiseconds.(Attribute no longer supported)
INT agentPortGvrpStatus	1.3.6.1.4.1.14179.1.2.12.1.16	INTEGER	read-write	The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.(Attribute no longer supported)
IAN agentPortIanaType	1.3.6.1.4.1.14179.1.2.12.1.3	IANAifType	read-only	The switch's Port Type
I32 agentPortIfIndex	1.3.6.1.4.1.14179.1.2.12.1.2	Integer32	read-only	The switch's Port IfIndex
INT agentPortLinkTrapMode	1.3.6.1.4.1.14179.1.2.12.1.9	INTEGER	read-write	If enabled, link up and link down traps will be sent for this port.
INT agentPortMirrorMode	1.3.6.1.4.1.14179.1.2.12.1.20	INTEGER	read-write	The switch's Port Mirror Mode. If enabled, then this is the port that the packets are mirrored to.
INT agentPortMulticastApplianceMode	1.3.6.1.4.1.14179.1.2.12.1.21	INTEGER	read-write	The Port Multicast Appliance Mode. If enabled, then this port allows multicast streams through it. At a time, a maximum of four ports including the gigabit ethernet port can have this mode enabled on them. This is to limit the number of multicast streams allowed through the switch at a given time.
INT agentPortOperationalStatus	1.3.6.1.4.1.14179.1.2.12.1.40	INTEGER	read-only	The current operational state of the port.
INT agentPortPhysicalMode	1.3.6.1.4.1.14179.1.2.12.1.7	INTEGER	read-write	The switch's Port Speed Mode. This is the configured physical mode.This object is read-only for gigabit ports
INT agentPortPhysicalStatus	1.3.6.1.4.1.14179.1.2.12.1.8	INTEGER	read-only	The switch's Port Physical Speed Status.This is the current actual speed.
INT agentPortPowerMode	1.3.6.1.4.1.14179.1.2.12.1.15	INTEGER	read-write	Enable/Disable the port's Power over ethernet. This doesn't apply to appliances that have no POE controller.
INT agentPortSTPMode	1.3.6.1.4.1.14179.1.2.12.1.4	INTEGER	read-write	The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port
INT agentPortSTPState	1.3.6.1.4.1.14179.1.2.12.1.5	INTEGER	read-only	The switch's Port Spanning Tree Protocol State
OID agentPortType	1.3.6.1.4.1.14179.1.2.12.1.12	OBJECT IDENTIFIER	read-only	This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object qbEnetDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object qbEnetPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
agentProductGroup	1.3.6.1.4.1.14179.1.1.4
I32 agentRadioUpDownTrapCount	1.3.6.1.4.1.14179.1.1.2.5	Integer32	read-only	The total number of AP Up/Down traps sent since last reset.
INT agentResetSystem	1.3.6.1.4.1.14179.1.3.10	INTEGER	read-write	reset the switch
agentResourceInfoGroup	1.3.6.1.4.1.14179.1.1.5
INT agentSaveConfig	1.3.6.1.4.1.14179.1.3.1	INTEGER	read-write	save config to NVRAM
INT agentSerialBaudrate	1.3.6.1.4.1.14179.1.2.1.5.2	INTEGER	read-write	Agent Serial Baudrate
I32 agentSerialCharacterSize	1.3.6.1.4.1.14179.1.2.1.5.3	Integer32	read-only	Agent Serial Character Size
agentSerialGroup	1.3.6.1.4.1.14179.1.2.1.5
INT agentSerialHWFlowControlMode	1.3.6.1.4.1.14179.1.2.1.5.4	INTEGER	read-only	Agent Serial Hardware Flow Control.
INT agentSerialParityType	1.3.6.1.4.1.14179.1.2.1.5.6	INTEGER	read-only	Agent Serial Parity Type
I32 agentSerialStopBits	1.3.6.1.4.1.14179.1.2.1.5.5	Integer32	read-only	Agent Serial Stop Bits
I32 agentSerialTimeout	1.3.6.1.4.1.14179.1.2.1.5.1	Integer32	read-write	Agent Serial Timeout
PHY agentServicePortBurnedInMacAddress	1.3.6.1.4.1.14179.1.2.4.4	PhysAddress	read-only	The switch's Service Port Burned-In MAC address (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
agentServicePortConfigGroup	1.3.6.1.4.1.14179.1.2.4
INT agentServicePortConfigProtocol	1.3.6.1.4.1.14179.1.2.4.5	INTEGER	read-write	The switch's Service Port config protocol (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
IP agentServicePortDefaultGateway	1.3.6.1.4.1.14179.1.2.4.3	IpAddress	read-write	Not Supported for release 1.0. The switch's Service Port default gateway. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
IP agentServicePortIPAddress	1.3.6.1.4.1.14179.1.2.4.1	IpAddress	read-write	The switch's Service Port IP address. (Service-port interface use is recommended instead of this group)
IP agentServicePortSubnetMask	1.3.6.1.4.1.14179.1.2.4.2	IpAddress	read-write	The switch's Service Port subnet mask. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
INT agentSnmpAuthenticationTrapFlag	1.3.6.1.4.1.14179.1.2.5.7.1	INTEGER	read-write	Authentication Flag - Enable/Disable authentication Flag.
INT agentSnmpBroadcastStormTrapFlag	1.3.6.1.4.1.14179.1.2.5.7.5	INTEGER	read-write	Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.
INT agentSnmpCommunityAccessMode	1.3.6.1.4.1.14179.1.2.5.5.1.4	INTEGER	read-create	The switch's Snmp Community Access Mode Access Mode - This value can be readOnly or readWrite. A community with a read-only access allows for switch information to be displayed. A community with a readWrite access allows for configuration changes to be made and for information to be displayed.
agentSnmpCommunityConfigEntry	1.3.6.1.4.1.14179.1.2.5.5.1		not-accessible	Switch's SNMP community Config entry
agentSnmpCommunityConfigTable	1.3.6.1.4.1.14179.1.2.5.5		not-accessible	A table of the switch's SNMP community Config entries
INT agentSnmpCommunityEnabled	1.3.6.1.4.1.14179.1.2.5.5.1.5	INTEGER	read-create	If community is Enabled
IP agentSnmpCommunityIPAddress	1.3.6.1.4.1.14179.1.2.5.5.1.2	IpAddress	read-create	The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.
IP agentSnmpCommunityIPMask	1.3.6.1.4.1.14179.1.2.5.5.1.3	IpAddress	read-create	The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.
STR agentSnmpCommunityName	1.3.6.1.4.1.14179.1.2.5.5.1.1	DisplayString	read-create	The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.
ROW agentSnmpCommunityStatus	1.3.6.1.4.1.14179.1.2.5.5.1.25	RowStatus	read-create	The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP manager associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.
agentSnmpConfigGroup	1.3.6.1.4.1.14179.1.2.5
INT agentSnmpLinkUpDownTrapFlag	1.3.6.1.4.1.14179.1.2.5.7.2	INTEGER	read-write	Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.
INT agentSnmpMultipleUsersTrapFlag	1.3.6.1.4.1.14179.1.2.5.7.3	INTEGER	read-write	Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session
INT agentSnmpSpanningTreeTrapFlag	1.3.6.1.4.1.14179.1.2.5.7.4	INTEGER	read-write	Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.
agentSnmpTrapFlagsConfigGroup	1.3.6.1.4.1.14179.1.2.5.7
U32 agentSnmpTrapPortNumber	1.3.6.1.4.1.14179.1.2.5.1	Unsigned32	read-write	Snmp Trap Port Number
agentSnmpTrapReceiverConfigEntry	1.3.6.1.4.1.14179.1.2.5.6.1		not-accessible	Switch's Snmp Trap Receiver Config entry
agentSnmpTrapReceiverConfigTable	1.3.6.1.4.1.14179.1.2.5.6		not-accessible	Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.
INT agentSnmpTrapReceiverEnabled	1.3.6.1.4.1.14179.1.2.5.6.1.3	INTEGER	read-create	The flag to enable the trap receiver. If disabled, no traps are sent to this receiver's IP Address.
IP agentSnmpTrapReceiverIPAddress	1.3.6.1.4.1.14179.1.2.5.6.1.2	IpAddress	read-create	SNMP network Manager IP Address. The IP Address traps will be sent to. Each IP address parameter is four integer numbers. The numbers range from 0 to 255. After creation of entry IP Address cannot be changed.
OCT agentSnmpTrapReceiverName	1.3.6.1.4.1.14179.1.2.5.6.1.1	OCTET STRING	read-create	The switch's Snmp Trap Receiver Name. This is the name of the remote network manager. the name can be up to 16 characters, and is case-sensitive.
ROW agentSnmpTrapReceiverStatus	1.3.6.1.4.1.14179.1.2.5.6.1.23	RowStatus	read-create	This object is used to create and delete instances of this table. The row, when created with the row status value of 'createAndGo' or 'createAndWait' is moved to the 'active' state automatically by the agent and remains in that state till the time the row is removed through the 'destroy' option.
agentSnmpV3ConfigGroup	1.3.6.1.4.1.14179.1.2.6
INT agentSnmpV3UserAccessMode	1.3.6.1.4.1.14179.1.2.6.2.1.2	INTEGER	read-create	Agent User Access Mode
OCT agentSnmpV3UserAuthenticationPassword	1.3.6.1.4.1.14179.1.2.6.2.1.5	OCTET STRING	read-create	SNMPv3 User Encryption Password
INT agentSnmpV3UserAuthenticationType	1.3.6.1.4.1.14179.1.2.6.2.1.3	INTEGER	read-create	SNMPv3 User Authentication none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication
agentSnmpV3UserConfigEntry	1.3.6.1.4.1.14179.1.2.6.2.1		not-accessible	User Config Entry
agentSnmpV3UserConfigTable	1.3.6.1.4.1.14179.1.2.6.2		not-accessible	User Config Table. Only creation and deletion of users is supported. All individual updates are not supported.
OCT agentSnmpV3UserEncryptionPassword	1.3.6.1.4.1.14179.1.2.6.2.1.6	OCTET STRING	read-create	SNMPv3 User Encryption Password
INT agentSnmpV3UserEncryptionType	1.3.6.1.4.1.14179.1.2.6.2.1.4	INTEGER	read-create	SNMPv3 User Encryption Must be set to none(1) if agentSnmpV3UserAuthenticationType is set to none(1). Setting this object will set the encryption password to an empty string. none(1) - no encryption used des(1) - DES encryption used
OCT agentSnmpV3UserName	1.3.6.1.4.1.14179.1.2.6.2.1.1	OCTET STRING	read-create	Agent User Name.
ROW agentSnmpV3UserStatus	1.3.6.1.4.1.14179.1.2.6.2.1.26	RowStatus	read-create	Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.
INT agentSnmpVersion1Status	1.3.6.1.4.1.14179.1.2.5.2	INTEGER	read-write	Snmp Version 1 Status
INT agentSnmpVersion2cStatus	1.3.6.1.4.1.14179.1.2.5.3	INTEGER	read-write	Snmp Version 2c Status
INT agentSnmpVersion3Status	1.3.6.1.4.1.14179.1.2.6.1	INTEGER	read-write	Snmp Version 3 Status
agentSpanningTreeConfigGroup	1.3.6.1.4.1.14179.1.2.7
INT agentSpanningTreeMode	1.3.6.1.4.1.14179.1.2.7.1	INTEGER	read-write	The switch's Spanning Tree Switch Status
INT agentSSHAllowNewMode	1.3.6.1.4.1.14179.1.2.1.2.4	INTEGER	read-write	Allow new SSH sessions (enable or disable) Config SSH disable means that no new SSH sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
I32 agentSwitchAddressAgingTimeout	1.3.6.1.4.1.14179.1.2.8.4.1.10	Integer32	read-write	The FDB entry's address aging timeout(in seconds)
agentSwitchAddressAgingTimeoutEntry	1.3.6.1.4.1.14179.1.2.8.4.1		not-accessible	Aging information about a specific Filtering Database.
agentSwitchAddressAgingTimeoutTable	1.3.6.1.4.1.14179.1.2.8.4		not-accessible	The switch's address aging timeout table
INT agentSwitchBroadcastControlMode	1.3.6.1.4.1.14179.1.2.8.2	INTEGER	read-write	The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discards) the broadcast traffic until the broadcast traffic returns to 10 percent or less.Upper limit for 10M link is 20% and lower limit is 10%. For 100M link Upper limit is 5% and lower limit is 2%
agentSwitchConfigGroup	1.3.6.1.4.1.14179.1.2.8
INT agentSwitchDot3FlowControlMode	1.3.6.1.4.1.14179.1.2.8.3	INTEGER	read-write	Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.
agentSwitchInfoGroup	1.3.6.1.4.1.14179.1.1.3
INT agentSwitchInfoLwappTransportMode	1.3.6.1.4.1.14179.1.1.3.1	INTEGER	read-only	The LWAPP transport mode specifies if the switch is operating in Layer2 or Layer3 mode. This attribute gives the current mode the switch is operating on.
INT agentSwitchInfoPowerSupply1Operational	1.3.6.1.4.1.14179.1.1.3.3	INTEGER	read-only	This is to indicate if the switch's Power Supply 1 is operational. This is applicable to the 4200 series and will always return true for the earlier device versions.
INT agentSwitchInfoPowerSupply1Present	1.3.6.1.4.1.14179.1.1.3.2	INTEGER	read-only	This is to indicate if the switch has Power Supply 1 present on it. This is applicable to the 4200 series and will always return true for the earlier device versions.
INT agentSwitchInfoPowerSupply2Operational	1.3.6.1.4.1.14179.1.1.3.5	INTEGER	read-only	This is to indicate if the switch's Power Supply 2 is operational.This is applicable to the 4200 series and will always return false for the earlier device versions.
INT agentSwitchInfoPowerSupply2Present	1.3.6.1.4.1.14179.1.1.3.4	INTEGER	read-only	This is to indicate if the switch has Power Supply 2 present on it. This is applicable to the 4200 series and will always return false for the earlier device versions.
INT agentSwitchLwappTransportMode	1.3.6.1.4.1.14179.1.2.8.5	INTEGER	read-write	The LWAPP transport mode decides if the switch is operating in the Layer2 or Layer3 mode. The switch needs to be rebooted for the mode change to take effect.
agentSystemGroup	1.3.6.1.4.1.14179.1.3
INT agentTelnetAllowNewMode	1.3.6.1.4.1.14179.1.2.1.2.3	INTEGER	read-write	Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
agentTelnetConfigGroup	1.3.6.1.4.1.14179.1.2.1.2
I32 agentTelnetLoginTimeout	1.3.6.1.4.1.14179.1.2.1.2.1	Integer32	read-write	Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 0 to 160. A value of 0 indicates that a Telnet session remains active indefinitely. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.
I32 agentTelnetMaxSessions	1.3.6.1.4.1.14179.1.2.1.2.2	Integer32	read-write	Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.
I32 agentTotalMemory	1.3.6.1.4.1.14179.1.1.5.2	Integer32	read-only	Total RAM of the switch in Kbytes.
agentTransferConfigGroup	1.3.6.1.4.1.14179.1.2.9
INT agentTransferConfigurationFileEncryption	1.3.6.1.4.1.14179.1.2.9.3	INTEGER	read-write	The configuration file can be encrypted before tftp upload from the switch and then decrypted before downloading to the switch when this option is enabled.
STR agentTransferConfigurationFileEncryptionKey	1.3.6.1.4.1.14179.1.2.9.4	DisplayString	read-write	This is the key to be used when encrypting the configuration file while upload from the switch or while decrypting the file after download to the switch.
INT agentTransferDownloadDataType	1.3.6.1.4.1.14179.1.2.9.2.5	INTEGER	read-write	Transfer download datatype configures the type of file to downloaded to the switch. The types for download are: - Code - Configuration - Certificates - Signatures - customWebauth- custom webauth tar ball
STR agentTransferDownloadFilename	1.3.6.1.4.1.14179.1.2.9.2.4	DisplayString	read-write	Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
agentTransferDownloadGroup	1.3.6.1.4.1.14179.1.2.9.2
INT agentTransferDownloadMode	1.3.6.1.4.1.14179.1.2.9.2.1	INTEGER	read-write	Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
STR agentTransferDownloadPath	1.3.6.1.4.1.14179.1.2.9.2.3	DisplayString	read-write	Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.
IP agentTransferDownloadServerIP	1.3.6.1.4.1.14179.1.2.9.2.2	IpAddress	read-write	Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
INT agentTransferDownloadStart	1.3.6.1.4.1.14179.1.2.9.2.6	INTEGER	read-write	Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
INT agentTransferDownloadStatus	1.3.6.1.4.1.14179.1.2.9.2.7	INTEGER	read-only	Indicates the current status of an download transfer.
U32 agentTransferDownloadTftpMaxRetries	1.3.6.1.4.1.14179.1.2.9.2.8	Unsigned32	read-write	Maximum number of retries to be allowed for a TFTP message packet.
U32 agentTransferDownloadTftpTimeout	1.3.6.1.4.1.14179.1.2.9.2.9	Unsigned32	read-write	Timeout in seconds for a TFTP message packet.
INT agentTransferUploadDataType	1.3.6.1.4.1.14179.1.2.9.1.5	INTEGER	read-write	Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - System trace - Trap log - Crash File
STR agentTransferUploadFilename	1.3.6.1.4.1.14179.1.2.9.1.4	DisplayString	read-write	Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
agentTransferUploadGroup	1.3.6.1.4.1.14179.1.2.9.1
INT agentTransferUploadMode	1.3.6.1.4.1.14179.1.2.9.1.1	INTEGER	read-write	Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
STR agentTransferUploadPath	1.3.6.1.4.1.14179.1.2.9.1.3	DisplayString	read-write	Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.
IP agentTransferUploadServerIP	1.3.6.1.4.1.14179.1.2.9.1.2	IpAddress	read-write	Transfer upload tftpserverip configures the IP address of the server where the file will be uploaded. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
INT agentTransferUploadStart	1.3.6.1.4.1.14179.1.2.9.1.6	INTEGER	read-write	Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
INT agentTransferUploadStatus	1.3.6.1.4.1.14179.1.2.9.1.7	INTEGER	read-only	Indicates the current status of an upload transfer.
agentTrapLogEntry	1.3.6.1.4.1.14179.1.1.2.4.1		not-accessible	Agent trap log entry
agentTrapLogGroup	1.3.6.1.4.1.14179.1.1.2
I32 agentTrapLogIndex	1.3.6.1.4.1.14179.1.1.2.4.1.1	Integer32	read-only	Unique index of trap entry
STR agentTrapLogSystemTime	1.3.6.1.4.1.14179.1.1.2.4.1.2	DisplayString	read-only	System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.
agentTrapLogTable	1.3.6.1.4.1.14179.1.1.2.4		not-accessible	Agent Trap Log
I32 agentTrapLogTotal	1.3.6.1.4.1.14179.1.1.2.1	Integer32	read-only	The total number of traps sent since last reset.
I32 agentTrapLogTotalSinceLastViewed	1.3.6.1.4.1.14179.1.1.2.3	Integer32	read-only	The number of traps sent since last viewed.
OCT agentTrapLogTrap	1.3.6.1.4.1.14179.1.1.2.4.1.22	OCTET STRING	read-only	Description of the trap sent.
agentWcpControllerInfoEntry	1.3.6.1.4.1.14179.1.1.6.7.1		not-accessible	Entry for a wireless controller on a WCP device.
IP agentWcpControllerInfoIpAddress	1.3.6.1.4.1.14179.1.1.6.7.1.10	IpAddress	read-only	The management IP Address of a controller.
U32 agentWcpControllerInfoPortNumber	1.3.6.1.4.1.14179.1.1.6.7.1.2	Unsigned32	read-only	The port number on the Wcp Device that a controller is residing on.
U32 agentWcpControllerInfoSlotNumber	1.3.6.1.4.1.14179.1.1.6.7.1.1	Unsigned32	read-only	The slot number on the Wcp device that a controller is residing on.
agentWcpControllerInfoTable	1.3.6.1.4.1.14179.1.1.6.7		not-accessible	A table of the wireless controllers on a WCP device.
I32 agentWcpControllerTableChecksum	1.3.6.1.4.1.14179.1.1.6.6	Integer32	read-only	This is the checksum that tracks the changes in the agentWcpControllerInfoTable. If there is any change in the information on this table, the checksum changes.
STR agentWcpDeviceName	1.3.6.1.4.1.14179.1.1.6.1	DisplayString	read-only	This is the name of the device this controller is residing on.
agentWcpInfoGroup	1.3.6.1.4.1.14179.1.1.6
IP agentWcpPeerIpAddress	1.3.6.1.4.1.14179.1.1.6.5	IpAddress	read-only	The IP Address of this controller's peer on the same slot on Wcp Device that this controller is residing on.
U32 agentWcpPeerPortNumber	1.3.6.1.4.1.14179.1.1.6.4	Unsigned32	read-only	The port number of this controller's peer on the same slot on Wcp Device that this controller is residing on.
U32 agentWcpPortNumber	1.3.6.1.4.1.14179.1.1.6.3	Unsigned32	read-only	The port number on the Wcp Device that this controller is residing on.
U32 agentWcpSlotNumber	1.3.6.1.4.1.14179.1.1.6.2	Unsigned32	read-only	The slot number on the Wcp Device that this controller is residing on.
NTF broadcastStormEndTrap	1.3.6.1.4.1.14179.1.50.3			Broadcast Storm End Log Trap.
NTF broadcastStormStartTrap	1.3.6.1.4.1.14179.1.50.2			Broadcast Storm Start Log Trap.
bsnSwitching	1.3.6.1.4.1.14179.1			This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration, statistics and status information about the controller. This includes controller statistics and provides information such as Inventory, Trap logs, memory and CPU. This MIB also provides configuration of CLI, SNMP, LAG, DHCP, Spanning Tree, etc. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
bsnSwitchingAgentConfigGroup	1.3.6.1.4.1.14179.1.51.2			This collection of objects provide switching configuration information.
bsnSwitchingAgentInfoGroup	1.3.6.1.4.1.14179.1.51.1			This collection of objects provide switching information.
bsnSwitchingAgentStatsGroup	1.3.6.1.4.1.14179.1.51.4			This collection of objects provide switching statistics.
bsnSwitchingAgentSystemGroup	1.3.6.1.4.1.14179.1.51.3			This collection of objects provide switching system information and config.
bsnSwitchingCompliance	1.3.6.1.4.1.14179.1.52.1			The compliance statement for the SNMP entities that implement the bsnSwitching module
bsnSwitchingCompliances	1.3.6.1.4.1.14179.1.52
bsnSwitchingGroups	1.3.6.1.4.1.14179.1.51
bsnSwitchingObsGroup	1.3.6.1.4.1.14179.1.51.5			This collection of objects are obsoleted in bsnSwitching module.
bsnSwitchingTrap	1.3.6.1.4.1.14179.1.51.6			This collection of objects provides switching related notification.
NTF fanFailureTrap	1.3.6.1.4.1.14179.1.50.9			Fan Failure Log Trap.
NTF linkFailureTrap	1.3.6.1.4.1.14179.1.50.4			trapMgrLinkFailureLogTrap.
NTF multipleUsersTrap	1.3.6.1.4.1.14179.1.50.1			Multiple Users Log Trap.
portStatsEntry	1.3.6.1.4.1.14179.1.4.1.1		not-accessible	A collection of statistics kept for a particular Ethernet interface.
I32 portStatsIndex	1.3.6.1.4.1.14179.1.4.1.1.1	Integer32	read-only	The value of this object uniquely identifies this portStatsEntry.
C32 portStatsPktsRx1519to1530Octets	1.3.6.1.4.1.14179.1.4.1.1.8	Counter32	read-only	The total number of packets (including bad packets) received that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).
C32 portStatsPktsTx1024to1518Octets	1.3.6.1.4.1.14179.1.4.1.1.7	Counter32	read-only	The total number of packets (including bad packets) transmitted that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
C32 portStatsPktsTx128to255Octets	1.3.6.1.4.1.14179.1.4.1.1.4	Counter32	read-only	The total number of packets (including bad packets) transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
C32 portStatsPktsTx1519to1530Octets	1.3.6.1.4.1.14179.1.4.1.1.9	Counter32	read-only	The total number of packets (including bad packets) transmitted that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).
C32 portStatsPktsTx256to511Octets	1.3.6.1.4.1.14179.1.4.1.1.5	Counter32	read-only	The total number of packets (including bad packets) transmitted that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
C32 portStatsPktsTx512to1023Octets	1.3.6.1.4.1.14179.1.4.1.1.6	Counter32	read-only	The total number of packets (including bad packets) transmitted that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
C32 portStatsPktsTx64OctetsEx	1.3.6.1.4.1.14179.1.4.1.1.2	Counter32	read-only	The total number of packets (including bad packets) transmitted that were 64 octets in length (excluding framing bits but including FCS octets).
C32 portStatsPktsTx65to127Octets	1.3.6.1.4.1.14179.1.4.1.1.3	Counter32	read-only	The total number of packets (including bad packets) transmitted that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
C32 portStatsPktsTxOversizeOctets	1.3.6.1.4.1.14179.1.4.1.1.30	Counter32	read-only	The total number of packets (including bad packets) transmitted that were more than 1530 octets in length. (excluding framing bits but including FCS octets).
portStatsTable	1.3.6.1.4.1.14179.1.4.1		not-accessible	A list of additional thernet statistics entries.
NTF powerSupplyStatusChangeTrap	1.3.6.1.4.1.14179.1.50.12			Power Supply Status Change Trap
productGroup1	1.3.6.1.4.1.14179.1.1.4.1
productGroup2	1.3.6.1.4.1.14179.1.1.4.2
productGroup3	1.3.6.1.4.1.14179.1.1.4.3
productGroup4	1.3.6.1.4.1.14179.1.1.4.4
stats	1.3.6.1.4.1.14179.1.4
NTF stpInstanceNewRootTrap	1.3.6.1.4.1.14179.1.50.10			STP Instance New Root Trap
NTF stpInstanceTopologyChangeTrap	1.3.6.1.4.1.14179.1.50.11			STP Instance Topology Change Trap
switchingTraps	1.3.6.1.4.1.14179.1.50
NTF vlanDefaultCfgFailureTrap	1.3.6.1.4.1.14179.1.50.7			Default Vlan Config Failure Log Trap
NTF vlanDeleteLastTrap	1.3.6.1.4.1.14179.1.50.6			Last Vlan Delete Log Trap
NTF vlanRequestFailureTrap	1.3.6.1.4.1.14179.1.50.5			Vlan Request Failure Log Trap
NTF vlanRestoreFailureTrap	1.3.6.1.4.1.14179.1.50.8			Vlan Restore Failure Log Trap

RFC description

Provides configuration, statistics, and status information for Cisco Airespace LWAPP controllers including inventory, memory, CPU, and LAG management.

Start monitoring Cisco (Airespace) Wireless LAN Controllers (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AIRESPACE-SWITCHING-MIB