ZTE-AN-ENVMON-MIB

All MIBs › ZTE-AN-ENVMON-MIB

Organization: ZTE Corporation

Last Updated: 2014-12-23

Category: ZTE Access Node (ZTE-AN) Management

Description: Monitors ZTE access node environmental conditions including temperature, voltage, and fan speed thresholds.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZTE-AN-ENVMON-MIB?

ZTE-AN-ENVMON-MIB is ZTE's environmental-monitoring module for its Access Node (AN) product line, covering the physical operating environment of the chassis rather than network traffic. It exposes environmental sensor data including chassis/ambient temperature, power-supply voltage readings, and fan-speed measurements, typically paired with configurable warning/critical thresholds for each. Its monitoring value is entirely in hardware health: this is exactly the MIB an operator uses to catch overheating (rising temperature past threshold), a failing or under-voltage power supply, or a fan slowing down or stopping, any of which can precede a hardware shutdown or damage if unaddressed. It follows the common pattern of vendor environmental-monitor MIBs (conceptually similar to the temperature/voltage/fan style seen in other vendors' ENVMON MIBs) though implemented independently for ZTE equipment. It is deployed on ZTE access node chassis in central-office or cabinet environments, where NMS platforms rely on ZTE-AN-ENVMON-MIB SNMP monitoring to continuously and proactively alert on environmental conditions.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZTE-AN-ENVMON-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE Access Node chassis

Monitoring Examples

No sample object names were provided for this module; based on the description, an admin would poll the chassis temperature and fan-speed objects to confirm cooling is adequate, and watch the power-supply voltage object against its configured threshold to catch a degrading power supply before it causes an outage.

What Can Be Monitored

chassis/ambient temperature
power supply voltage
fan speed
environmental threshold alerts

Imported Objects

From HC-PerfHist-TC-MIB

HCPerfCurrentCount

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

From ZTE-AN-SMI

zxAccessNode	MODULE-IDENTITY
zxAnEquipment	OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using zxAnCardEnvHis15MinTemp OID:

Select a ZTE Access Node chassis (temperature/power-supply-voltage/fan-speed threshold status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type zxAnCardEnvHis15MinTemp into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The 15 minutes interval average temperature of card. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the reported value exceeds the level expected for healthy operation, since sustained high temperature often precedes thermal shutdown or hardware degradation. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
zxAnEnvMonMib	1.3.6.1.4.1.3902.1082.10.10			This MIB defines zte Access Node managed environment monitor.
zxAnEnvMonGlobalObjects	1.3.6.1.4.1.3902.1082.10.10.1
BIT zxAnEnvMonCapabilities	1.3.6.1.4.1.3902.1082.10.10.1.1	Bits	read-only	The environment management capabilities of this equipment.The bit value 1 means the function represented by this bit is supported by this equipment. NOTE: Not recommended to display it in NMS.
zxAnEnvMonObjects	1.3.6.1.4.1.3902.1082.10.10.2
zxAnEnvParamObjects	1.3.6.1.4.1.3902.1082.10.10.2.1
zxAnEnvParamGlobalObjects	1.3.6.1.4.1.3902.1082.10.10.2.1.1
INT zxAnEnvCardShutdownReason	1.3.6.1.4.1.3902.1082.10.10.2.1.1.1	INTEGER	accessible-for-notify	The alarm reason of zxAnEnvCardShutdownAlm. envHighTemperature(1): Environment temperature is too high. cardHighTemperature(2):Card self temperature is too high. chipHighTemperature(3):Card's chip temperature is too high. emergencyPowerSaving(4):Emergency power saving action has been taken caused by AC power failure.
zxAnEnvParamTable	1.3.6.1.4.1.3902.1082.10.10.2.1.5		not-accessible	This table includes environment temperature information.
zxAnEnvParamEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1		not-accessible	The entry of zxAnEnvParamTable.
I32 zxAnEnvRack	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.1	Integer32	not-accessible	The index of rack.
I32 zxAnEnvShelf	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.2	Integer32	not-accessible	The index of shelf.
I32 zxAnEnvTemp	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.3	Integer32	read-only	The temperature of the environment.
I32 zxAnEnvTempHighAlmThreshold	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.4	Integer32	read-write	The temperature high alarm threshold of the environment.
I32 zxAnEnvTempCriticalAlmThreshold	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.5	Integer32	read-only	The temperature critical alarm threshold of the environment.
I32 zxAnEnvTempLowAlmThreshold	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.6	Integer32	read-write	The temperature low alarm threshold of the environment.
I32 zxAnEnvShelfPowerConsumption	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.7	Integer32	read-only	Power consumption of the shelf. Value 0 means not available.
I32 zxAnEnvShelfVoltage	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.8	Integer32	read-only	Voltage of the shelf. Value 0 means not available.
I32 zxAnEnvShelfCurrent	1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.9	Integer32	read-only	Current of the shelf. Value 0 means not available.
zxAnCardEnvParamTable	1.3.6.1.4.1.3902.1082.10.10.2.1.6		not-accessible	This table includes card temperature information.
zxAnCardEnvParamEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1		not-accessible	The entry of zxAnCardEnvParamTable.
I32 zxAnEnvSlot	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.1	Integer32	not-accessible	The index of slot, the range is [0,20] of 19-inch shelf and [0,22] of 21-inch shelf.
I32 zxAnCardTemp	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.2	Integer32	read-only	The current temperature of the card environment. NOTE: 1. In current system, only certain cards support temperature-reading, such as SCXL, GTGOD cards. 2. If the card is not configured, we cannot get its temperature. 3. For the configured but not support temperature-reading cards, we use -1000 as an invalid temperature value to note its temperature.
I32 zxAnCardPowerConsumption	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.3	Integer32	read-only	Power consumption of the card. Value 0 means not available.
I32 zxAnCardVoltage	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.4	Integer32	read-only	Voltage of the card. Value 0 means not available.
I32 zxAnCardCurrent	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.5	Integer32	read-only	Current of the card. Value 0 means not available.
I32 zxAnCardCriticalTempAlmThreshold	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.6	Integer32	accessible-for-notify	The critical temperature alarm threshold of the card.
I32 zxAnCardOptHighestTemp	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.7	Integer32	accessible-for-notify	The highest temperature of the optical modules in the card.
I32 zxAnCardOptCriticalTempAlmThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.8	Integer32	accessible-for-notify	The critical optical temperature alarm threshold.
I32 zxAnCardOptHighestTempPortNo	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.9	Integer32	accessible-for-notify	The port No. which the optical module is located at, and the optical module has the highest temperature.
I32 zxAnCardHeatRadiationAlmThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.10	Integer32	accessible-for-notify	The heat radiation abnormal alarm threshold of the card.
I32 zxAnCardTempHighAccuracy	1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.11	Integer32	read-only	The high accuracy value of zxAnCardTemp.
zxAnCardEnvHis15MinPerfTable	1.3.6.1.4.1.3902.1082.10.10.2.1.7		not-accessible	The 15 minutes interval performance data table of card temperature.
zxAnCardEnvHis15MinPerfEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.7.1		not-accessible	The 15 minutes interval performance data entry of card temperature.
I32 zxAnCardEnvHis15MinIntervalNo	1.3.6.1.4.1.3902.1082.10.10.2.1.7.1.1	Integer32	not-accessible	Performance data interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
DAT zxAnCardEnvHis15MinDateTime	1.3.6.1.4.1.3902.1082.10.10.2.1.7.1.2	DateAndTime	read-only	The 15 minutes interval performance data generation time.
C64 zxAnCardEnvHis15MinTempEx	1.3.6.1.4.1.3902.1082.10.10.2.1.7.1.3	Counter64	read-only	The 15 minutes interval average temperature of card.
zxAnCardEnvHis1DayPerfTable	1.3.6.1.4.1.3902.1082.10.10.2.1.8		not-accessible	The 1 day interval performance data table of card temperature.
zxAnCardEnvHis1DayPerfEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.8.1		not-accessible	The 1 day interval performance data entry of card temperature.
I32 zxAnCardEnvHis1DayIntervalNo	1.3.6.1.4.1.3902.1082.10.10.2.1.8.1.1	Integer32	not-accessible	Performance data interval number 1 is the the most recent previous interval; interval 7 is 1 week ago. Intervals 2..7 are optional.
DAT zxAnCardEnvHis1DayDateTime	1.3.6.1.4.1.3902.1082.10.10.2.1.8.1.2	DateAndTime	read-only	The 1 day interval performance data generation time.
C64 zxAnCardEnvHis1DayTemp	1.3.6.1.4.1.3902.1082.10.10.2.1.8.1.3	Counter64	read-only	The 1 day interval average temperature of card.
zxAnCardEnvAlmProfileConfTable	1.3.6.1.4.1.3902.1082.10.10.2.1.9		not-accessible	The performance alarm threshold profile items configuration table of card temperature.
zxAnCardEnvAlmProfileConfEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1		not-accessible	The performance alarm threshold profile items configuration entry of card temperature.
STR zxAnCardEnvAlmProfileName	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.1	DisplayString	not-accessible	The performance alarm threshold profile name.
OID zxAnCardEnvPerfVariable	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.2	OBJECT IDENTIFIER	not-accessible	The object identifier of performance variables.
HCP zxAnCardEnvRiseAlmThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.3	HCPerfCurrentCount	read-create	The threshold for rising alarm.
HCP zxAnCardEnvClrRiseAlmThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.4	HCPerfCurrentCount	read-create	The threshold for rising alarm restore.
HCP zxAnCardEnvRiseWarnThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.5	HCPerfCurrentCount	read-create	The threshold for rising warning.
HCP zxAnCardEnvClrRiseWarnThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.6	HCPerfCurrentCount	read-create	The threshold for rising warning restore.
HCP zxAnCardEnvFallWarnThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.7	HCPerfCurrentCount	read-create	The threshold for falling warning.
HCP zxAnCardEnvClrFallWarnThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.8	HCPerfCurrentCount	read-create	The threshold for falling warning restore.
HCP zxAnCardEnvFallAlmThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.9	HCPerfCurrentCount	read-create	The threshold for falling alarm.
HCP zxAnCardEnvClrFallAlmThresh	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.10	HCPerfCurrentCount	read-create	The threshold for falling alarm restore.
ROW zxAnCardEnvAlmPrfConfRowStatus	1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.50	RowStatus	read-create	The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
zxAnCardEnvAlmProfileApplyTable	1.3.6.1.4.1.3902.1082.10.10.2.1.10		not-accessible	The performance alarm threshold profile application table of card temperature.
zxAnCardEnvAlmProfileApplyEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.10.1		not-accessible	The performance alarm threshold profile application entry of card temperature.
STR zxAnCardEnvAlmPrf	1.3.6.1.4.1.3902.1082.10.10.2.1.10.1.1	DisplayString	read-create	The performance alarm threshold profile.
ROW zxAnCardEnvAlmPrfApplyRowStatus	1.3.6.1.4.1.3902.1082.10.10.2.1.10.1.50	RowStatus	read-create	The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
zxAnCardEnvAlmProfileTable	1.3.6.1.4.1.3902.1082.10.10.2.1.11		not-accessible	The performance alarm threshold profile table of card temperature.
zxAnCardEnvAlmProfileEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.11.1		not-accessible	The performance alarm threshold profile entry of card temperature.
ROW zxAnCardEnvAlmPrfRowStatus	1.3.6.1.4.1.3902.1082.10.10.2.1.11.1.50	RowStatus	read-create	The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
zxAnEnvOverheatProtectTable	1.3.6.1.4.1.3902.1082.10.10.2.1.13		not-accessible	Environment overheat protection table.
zxAnEnvOverheatProtectEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.13.1		not-accessible	Environment overheat protection entry. To modify zxAnEnvOverheatProtectEnable from disabled to enabled, zxAnEnvOverheatProtectEnable is mandatory, zxAnEnvOverheatProtectDelay is optional. To modify zxAnEnvOverheatProtectEnable from enabled to disabled, only zxAnEnvOverheatProtectEnable is mandatory.
INT zxAnEnvOverheatProtectEnable	1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.1	INTEGER	read-write	Enables or disables the environment overheat protection function.
I32 zxAnEnvOverheatProtectDelay	1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.2	Integer32	read-write	The delaying time between two steps. For example, when temperature is higher than the threshold, takes an action as the step 1, and delays the value of zxAnEnvOverheatProtectDelay, if the temperature is still higher than the threshold, takes an action as step 2.
ZXA zxAnEnvOverheatProtectFirstStep	1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.3	ZxAnEnvShutdownServiceType	read-write	The first step when the environment temperature exceeds zxAnEnvTempHighAlmThreshold.
ZXA zxAnEnvOverheatProtectSecondStep	1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.4	ZxAnEnvShutdownServiceType	read-write	The second step when the environment temperature still exceeds zxAnEnvTempHighAlmThreshold after first step has been done.
zxAnEnvCardOverheatProtectTable	1.3.6.1.4.1.3902.1082.10.10.2.1.14		not-accessible	Card overheat protection table.
zxAnEnvCardOverheatProtectEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.14.1		not-accessible	Card overheat protection entry.
INT zxAnEnvCardCriticalTempProtectEn	1.3.6.1.4.1.3902.1082.10.10.2.1.14.1.1	INTEGER	read-write	Enables or disables the card critical temperature protection function. If it is enabled, the card will be stopped when the card temperature is higher than the card critical temperature.
zxAnCardEnvHisMinPerfTable	1.3.6.1.4.1.3902.1082.10.10.2.1.15		not-accessible	The 5 minutes or 15 minutes interval environmental monitoring performance data table of card.
zxAnCardEnvHisMinPerfEntry	1.3.6.1.4.1.3902.1082.10.10.2.1.15.1		not-accessible	The 5 minutes or 15 minutes interval environmental monitoring performance data entry of card.
I32 zxAnCardEnvHMinIntervalNo	1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.1	Integer32	not-accessible	The performance data interval number. 1 means the the most recent previous interval; If the performance collection interval is 5 minutes, intervals 2..288 are optional. If the performance collection interval is 15 minutes, intervals 2..96 are optional.
INT zxAnCardEnvHMinIntervalValidData	1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.2	INTEGER	read-only	Performance data validity.
DAT zxAnCardEnvHMinDateTime	1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.3	DateAndTime	read-only	The 5 minutes or 15 minutes interval performance data generation time.
I32 zxAnCardEnvHMinTemperature	1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.4	Integer32	read-only	The average temperature of card in the historical 5 minutes or 15 minutes. If the card does not have this attribute, it should be -1000.
I32 zxAnCardEnvHMinVoltage	1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.5	Integer32	read-only	The average voltage of card in the historical 5 minutes or 15 minutes. If the card does not have this attribute, it should be 0.
I32 zxAnCardEnvHMinPowerConsumption	1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.6	Integer32	read-only	The average power consumption of card in the historical 5 minutes or 15 minutes. If the card does not have this attribute, it should be 0.
zxAnEnvMonInterfaceObjects	1.3.6.1.4.1.3902.1082.10.10.2.2
zxAnEnvMonInterfaceTable	1.3.6.1.4.1.3902.1082.10.10.2.2.5		not-accessible	This table includes the environment interface information.
zxAnEnvMonInterfaceEntry	1.3.6.1.4.1.3902.1082.10.10.2.2.5.1		not-accessible	The entry of zxAnEnvMonInterfaceTable.
INT zxAnEnvMonInterfaceUsage	1.3.6.1.4.1.3902.1082.10.10.2.2.5.1.1	INTEGER	read-write	The equipment type connected to the environment monitor interface.
INT zxAnEnvEpmConnectPort	1.3.6.1.4.1.3902.1082.10.10.2.2.5.1.2	INTEGER	read-write	The port no which epm connect
INT zxAnEnvBackplaneInterfaceUsage	1.3.6.1.4.1.3902.1082.10.10.2.2.5.1.3	INTEGER	read-write	The equipment type connected to the Backplane Interface. fan(1): the fan connect to the Backplane Interface; noUse(3): not used; noSupport(255):not support.
zxAnEnvPowerSupplyObjects	1.3.6.1.4.1.3902.1082.10.10.2.3
zxAnPowerSupplyGlobalObjects	1.3.6.1.4.1.3902.1082.10.10.2.3.1
INT zxAnEnvEmergencyPowerSaveEnable	1.3.6.1.4.1.3902.1082.10.10.2.3.1.1	INTEGER	read-write	Enables or disables the emergency power saving.
I32 zxAnEnvEmergencyPowerSaveDelay	1.3.6.1.4.1.3902.1082.10.10.2.3.1.2	Integer32	read-write	If AC power failure lasts more than zxAnEnvEmergencyPowerSaveDelay, emergency power saving action will be taken.
I32 zxAnEnvEmergencyPowerSaveRecover	1.3.6.1.4.1.3902.1082.10.10.2.3.1.3	Integer32	read-write	If AC power recovered, after this delay, the emergency power save action will be cancelled.
ZXA zxAnEnvEmergencyPowerSaveSvcType	1.3.6.1.4.1.3902.1082.10.10.2.3.1.4	ZxAnEnvShutdownServiceType	read-write	The service types will be shut down in emergency power saving action.
INT zxAnEnvPowerMode	1.3.6.1.4.1.3902.1082.10.10.2.3.1.5	INTEGER	read-write	The current power supply mode of the equipment, emergency power saving action is on the basis of the power mode zxAnEnvPowerMode. normal(1) means using AC power as power supply. battery(2) means using storage battery as power supply.
I32 zxAnEnvEmergencyBatteryVoltage	1.3.6.1.4.1.3902.1082.10.10.2.3.1.6	Integer32	read-only	The current voltage of the battery.
I32 zxAnEnvEmergencyBatteryThreshold	1.3.6.1.4.1.3902.1082.10.10.2.3.1.7	Integer32	read-write	The threshold of the battery voltage. If the battery voltage is less than zxAnEnvEmergencyBatteryThreshold, the emergency power saving action will be taken.
INT zxAnEnvEnergySavingLevel	1.3.6.1.4.1.3902.1082.10.10.2.3.1.8	INTEGER	read-write	level1(1): Level 1 means that the energy saving module action will be taken automatically while the following conditions are detected: 1. There is no card plugged in the slot or the card plugged in the slot has been power off. 2. The actual card type is not same as the configured card type. level2(2): Level 2 means that the energy saving module action will be taken automatically while the following conditions are detected: 1. There is no card plugged in the slot or the card plugged in the slot has been power off. 2. The actual card type is not same as the configured card type. 3. There is no ONU which is configured on the card or on the port. level3(3): Level 3 means that the energy saving module action will be taken automatically while the following conditions are detected: 1. There is no card plugged in the slot or the card plugged in the slot has been power off. 2. The actual card type is not same as the configured card type. 3. There is no ONU which is configured on the card or on the port. 4. If all the uplink ports down, all the cards except the uplink card will be power off.
zxAnPowerSupplyCapabilityTable	1.3.6.1.4.1.3902.1082.10.10.2.3.10		not-accessible	This table includes power supply capability table.
zxAnPowerSupplyCapabilityEntry	1.3.6.1.4.1.3902.1082.10.10.2.3.10.1		not-accessible	The entry of zxAnPowerSupplyCapabilityTable.
I32 zxAnPowerSupplyMaxPowerNum	1.3.6.1.4.1.3902.1082.10.10.2.3.10.1.1	Integer32	read-only	The max number of power supply in the equipment.
zxAnPowerSupplyTable	1.3.6.1.4.1.3902.1082.10.10.2.3.11		not-accessible	This table includes power supply table.
zxAnPowerSupplyEntry	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1		not-accessible	An entry in zxAnPowerSupplyTable.
INT zxAnPowerSupplyOperStatus	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.1	INTEGER	read-only	The operational status of the power supply module.
I32 zxAnPowerSupplyInVoltage	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.2	Integer32	read-only	The actual input volts of the power supply module.
INT zxAnPowerSupplyInVoltageStatus	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.3	INTEGER	read-only	The volt status of the power supply. normal(1) -- The input power is normal. overVoltage(2) -- The input power is over voltage. underVoltage(3) -- The input power is under voltage. off(4)) -- No power input.
I32 zxAnPowerInVoltageUpperThresh	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.4	Integer32	read-write	The upper threshold of input volts.The alarm should be generated when zxAnPowerSupplyInVoltage exceeds this threshold. If it is 0, no alarm reported to manager.
I32 zxAnPowerInVoltageLowerThresh	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.5	Integer32	read-write	The lower threshold of input volts.The alarm should be generated when zxAnPowerSupplyInVoltage is lower than this threshold. If it is 0, no alarm reported to manager.
I32 zxAnPowerSupplyInCurrent	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.6	Integer32	read-only	The actual current of the power supply module.
I32 zxAnPowerInCurrentThresh	1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.7	Integer32	read-write	The upper threshold of input current.The alarm should be generated when zxAnPowerSupplyInCurrent exceeds this threshold. If it is 0, no alarm reported to manager.
zxAnEnvEnergySavingTable	1.3.6.1.4.1.3902.1082.10.10.2.3.12		not-accessible	The energy saving status table of the NE.
zxAnEnvEnergySavingEntry	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1		not-accessible	An entry in zxAnEnvEnergySavingTable.
I32 zxAnEnvEnergySavingRack	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.1	Integer32	not-accessible	The rack number.
I32 zxAnEnvEnergySavingShelf	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.2	Integer32	not-accessible	The shelf number.
I32 zxAnEnvEnergySavingSlot	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.3	Integer32	not-accessible	The slot number.
I32 zxAnEnvEnergySavingPort	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.4	Integer32	not-accessible	The port number. If the card is power off, this object will be set to 255.
INT zxAnEnvEnergySavingStatus	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.5	INTEGER	read-only	The energy saving status.
INT zxAnEnvEnergySavingReason	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.6	INTEGER	read-only	The energy saving reason.
DAT zxAnEnvEnergySavingOccurringTime	1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.7	DateAndTime	read-only	The energy saving occurring time.
zxAnEnvFanObjects	1.3.6.1.4.1.3902.1082.10.10.2.4
zxAnEnvFanTrayTable	1.3.6.1.4.1.3902.1082.10.10.2.4.10		not-accessible	The Fan Tray Control table, with rack and shelf information.
zxAnEnvFanTrayEntry	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1		not-accessible	An entry in the zxAnEnvFanTrayTable.
INT zxAnFanTrayAlarmBeepEnable	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.1	INTEGER	read-write	The control status of the fan alarm beep.
INT zxAnFanTrayAutoSwitchByCardUp	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.2	INTEGER	read-write	Enable/disable fan auto switch with card installation. If it is enabled, the fan under the card should be switched to running status when the card is installed. Otherwise, the fan should be shutdown.
STR zxAnFanTrayHardwareVersion	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.3	DisplayString	read-only	The hardware version of the fan tray
STR zxAnFanTraySoftwareVersion	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.4	DisplayString	read-only	The software version of the fan tray
INT zxAnFanTraySpeedCtrlMode	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.5	INTEGER	read-write	The speed control mode of the fan. When this value is fixSpeed,zxAnFanTrayAdminStatus, zxAnFanTrayConfSpeedLevel,zxAnEnvFanAdminStatus and zxAnEnvFanConfSpeedLevel can be configured.
I32 zxAnFanTrayLowSpeed	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.6	Integer32	read-write	The speed value of the fan's low speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
I32 zxAnFanTrayStdSpeed	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.7	Integer32	read-write	The speed value of the fan's standard speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
I32 zxAnFanTrayHighSpeed	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.8	Integer32	read-write	The speed value of the fan's high speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
I32 zxAnFanTraySuperSpeed	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.9	Integer32	read-write	The speed value of the fan's super speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
I32 zxAnFanTrayLowSpeedShiftTemp	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.10	Integer32	read-write	The temperature to activate the fan tray to shift to the low speed level.
I32 zxAnFanTrayStdSpeedShiftTemp	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.11	Integer32	read-write	The temperature to activate the fan tray to shift to the standard speed level.
I32 zxAnFanTrayHighSpeedShiftTemp	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.12	Integer32	read-write	The temperature to activate the fan tray to shift to the high speed level.
I32 zxAnFanTraySuperSpeedShiftTemp	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.13	Integer32	read-write	The temperature to activate the fan tray to shift to the super speed level.
INT zxAnFanTrayLowSpeedPercent	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.14	INTEGER	read-write	The percentage of speed of the low speed level.
INT zxAnFanTrayStdSpeedPercent	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.15	INTEGER	read-write	The percentage of speed of the standard speed level.
INT zxAnFanTrayHighSpeedPercent	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.16	INTEGER	read-write	The percentage of speed of the high speed level.
INT zxAnFanTraySuperSpeedPercent	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.17	INTEGER	read-write	The percentage of speed of the super speed level.
INT zxAnFanTrayAdminStatus	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.18	INTEGER	read-write	The administrative status of the fan tray. When zxAnFanTrayAdminStatus is configured, all the zxAnEnvFanAdminStatus values are consistent with zxAnFanTrayAdminStatus.
INT zxAnFanTrayConfSpeedLevel	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.19	INTEGER	read-write	The configured speed level of the fan tray. When zxAnFanTrayConfSpeedLevel is configured, all the zxAnEnvFanConfSpeedLevel values are consistent with zxAnFanTrayConfSpeedLevel. This variable is valid if zxAnFanTrayAdminStatus is up.
I32 zxAnFanTrayPowerConsumption	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.20	Integer32	read-only	Power consumption of the fan tray. Value 0 means not available.
STR zxAnFanTraySn	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.21	DisplayString	read-write	The serial number of fan tray.
I32 zxAnFanTrayVoltage	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.22	Integer32	read-only	Voltage of the fan tray. Value 0 means not available.
I32 zxAnFanTrayCurrent	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.23	Integer32	read-only	Current of the fan tray. Value 0 means not available.
I32 zxAnFanTrayTemp	1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.24	Integer32	read-only	The temperature of the fan tray.
zxAnEnvFanTable	1.3.6.1.4.1.3902.1082.10.10.2.4.11		not-accessible	This table includes speed information and operational status of the fan units.
zxAnEnvFanEntry	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1		not-accessible	The entry of zxAnEnvFanTable.
I32 zxAnEnvFanIndex	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.1	Integer32	not-accessible	The index of this fan unit. For 19-inch shelf, there are 3 fans in each fan tray. The fan index should be integer in [1,3]. For 21-inch shelf, there are 4 fans. The fan index should be integer in [1,4].
INT zxAnEnvFanConfSpeedLevel	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.2	INTEGER	read-write	The configured speed level of the fan unit singly.
INT zxAnEnvFanActualSpeedLevel	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.3	INTEGER	read-only	The actual speed level of the fan unit.
INT zxAnEnvFanAdminStatus	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.4	INTEGER	read-write	The administrative status of the fan unit singly.
INT zxAnEnvFanOperStatus	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.5	INTEGER	read-only	The operational status of the fan unit.
INT zxAnEnvFanOnlineStatus	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.6	INTEGER	read-only	The actual online status of the fan unit.
I32 zxAnEnvFanActualSpeed	1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.7	Integer32	read-only	The actual speed of the fan unit. NOTE: If not supported, NMS should use the speed value of zxAnEnvFanActualSpeedLevel.
zxAnEnvFanTrayResetObjects	1.3.6.1.4.1.3902.1082.10.10.2.4.12
I32 zxAnEnvFanTrayResetRack	1.3.6.1.4.1.3902.1082.10.10.2.4.12.1	Integer32	read-write	The rack number of the fan tray.
STR zxAnEnvFanTrayResetShelfList	1.3.6.1.4.1.3902.1082.10.10.2.4.12.2	DisplayString	read-write	The shelf number list of the fan tray. They can be reset in batch, for example: 1,2,3. Setting this object to empty means all the fan trays connected with zxAnEnvFanTrayRack will be reset.
INT zxAnEnvFanTrayResetAction	1.3.6.1.4.1.3902.1082.10.10.2.4.12.3	INTEGER	read-write	Reset the fan trays. To query this object, always return 1.
zxAnEnvDeviceObjects	1.3.6.1.4.1.3902.1082.10.10.2.5
zxAnEnvDeviceTable	1.3.6.1.4.1.3902.1082.10.10.2.5.2		not-accessible	The table of environment device.
zxAnEnvDeviceEntry	1.3.6.1.4.1.3902.1082.10.10.2.5.2.1		not-accessible	The entry of the zxAnEnvDeviceTable.
I32 zxAnEnvDeviceId	1.3.6.1.4.1.3902.1082.10.10.2.5.2.1.1	Integer32	not-accessible	The ID of this environment device. Value 1-50 is default value which can not be modified or deleted. If add a new device, the ID will be starting from 51.
STR zxAnEnvDeviceName	1.3.6.1.4.1.3902.1082.10.10.2.5.2.1.2	DisplayString	read-create	The name of the environment device.
ROW zxAnEnvDeviceRowStatus	1.3.6.1.4.1.3902.1082.10.10.2.5.2.1.50	RowStatus	read-create	The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
zxAnEnvDevMonSwitchTable	1.3.6.1.4.1.3902.1082.10.10.2.5.3		not-accessible	The table of the switch which monitors environment device.
zxAnEnvDevMonSwitchEntry	1.3.6.1.4.1.3902.1082.10.10.2.5.3.1		not-accessible	The entry of the zxAnEnvDevMonSwitchTable.
I32 zxAnEnvDevMonSwitchId	1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.1	Integer32	not-accessible	The ID of the switch.
I32 zxAnEnvDevMonSwitchDeviceId	1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.2	Integer32	read-write	The ID of the device which monitored by the switch. Value 0 means this switch does not monitor any device.
INT zxAnEnvDevMonSwitchTrapEnable	1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.3	INTEGER	read-write	Enables or disables the environment device abnormal trap.
INT zxAnEnvDevMonSwitchNormalStatus	1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.4	INTEGER	read-write	The normal status of the environment device.
INT zxAnEnvDevMonSwitchCurrStatus	1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.5	INTEGER	read-only	The current status of the environment device.
zxAnEnvMonNotifications	1.3.6.1.4.1.3902.1082.10.10.3
zxAnEnvMonTempTraps	1.3.6.1.4.1.3902.1082.10.10.3.1
NTF zxAnEnvHighTempAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.1			The environment temperature has exceeded high temperature threshold zxAnEnvTempHighAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
NTF zxAnEnvHighTempClr	1.3.6.1.4.1.3902.1082.10.10.3.1.2			The environment temperature has returned to normal operating temperature from zxAnEnvTempHighAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
NTF zxAnEnvTempSensorFailure	1.3.6.1.4.1.3902.1082.10.10.3.1.5			It indicates that the temperature sensor is in fault.
NTF zxAnEnvCriticalTempAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.6			The environment temperature has exceeded critical temperature threshold zxAnEnvTempCriticalAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
NTF zxAnEnvCriticalTempClr	1.3.6.1.4.1.3902.1082.10.10.3.1.7			The environment temperature has returned to normal operating temperature from zxAnEnvTempCriticalAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
NTF zxAnEnvLowTempAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.8			The environment temperature is below low temperature threshold zxAnEnvTempLowAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
NTF zxAnEnvLowTempClr	1.3.6.1.4.1.3902.1082.10.10.3.1.9			The environment temperature has returned to normal operating temperature from zxAnEnvTempLowAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
NTF zxAnEnvCardShutdownAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.30			A zxAnEnvCardShutdownAlm trap is sent when the card has been shut down because agent has detected that the temperature is too high or the AC power is failure and the battery voltage is lower than zxAnEnvEmergencyBatteryThreshold. zxAnEnvCardShutdownReason indicates the real reason. When zxAnEnvCardShutdownReason is envHighTemperature ( 1 ), it means the environment temperature is too high, zxAnEnvTemp is the value of current environment temperature, zxAnCardTemp is invalid and should be zero. zxAnEnvEmergencyBatteryVoltage and zxAnEnvEmergencyBatteryThreshold are invalid and should be zero. When zxAnEnvCardShutdownReason is cardHighTemperature ( 2 ), it means the card temperature is too high, zxAnCardTemp is the value of current card temperature, zxAnEnvTemp is invalid and should be zero. zxAnEnvEmergencyBatteryVoltage and zxAnEnvEmergencyBatteryThreshold are invalid and should be zero. When zxAnEnvCardShutdownReason is chipHighTemperature ( 3 ), it means the temperature of the chip on the card is too high, zxAnCardTemp and zxAnEnvTemp are invalid and should be zero. zxAnEnvEmergencyBatteryVoltage and zxAnEnvEmergencyBatteryThreshold are invalid and should be zero. When zxAnEnvCardShutdownReason is emergencyPowerSaving ( 4 ), it means the AC power is failure, the emergency power saving action has been taken, zxAnCardTemp and zxAnEnvTemp are invalid and should be zero. zxAnEnvEmergencyBatteryVoltage is the value of the current battery voltage, zxAnEnvEmergencyBatteryThreshold is the threshold of the battery voltage.
NTF zxAnEnvCardShutdownClr	1.3.6.1.4.1.3902.1082.10.10.3.1.31			A zxAnEnvCardShutdownClr trap is sent when the card temperature becomes normal, or the environment temperature becomes normal, or the chip temperature becomes normal, or the battery voltage is higher than zxAnEnvEmergencyBatteryThreshold or AC power becomes normal.
NTF zxAnEnvTemperatureAbnormalAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.32			In temperature control mode, a zxAnEnvTemperatureAbnormalAlm trap is sent when the environment temperature can't be read.
NTF zxAnEnvTemperatureAbnormalClr	1.3.6.1.4.1.3902.1082.10.10.3.1.33			A zxAnEnvTemperatureAbnormalClr trap is sent when the zxAnEnvTemperatureAbnormalAlm is cleared.
NTF zxAnEnvNearCriticalTempAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.34			A zxAnEnvNearCriticalTempAlm trap is sent when the environment temperature is close to the environment critical temperature alarm threshold.
NTF zxAnEnvNearCriticalTempClr	1.3.6.1.4.1.3902.1082.10.10.3.1.35			A zxAnEnvNearCriticalTempClr trap is sent when the zxAnEnvNearCriticalTempAlm is cleared.
NTF zxAnEnvCardNearCriticalTempAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.36			A zxAnEnvCardNearCriticalTempAlm trap is sent when the card temperature is close to the card critical temperature alarm threshold.
NTF zxAnEnvCardNearCriticalTempClr	1.3.6.1.4.1.3902.1082.10.10.3.1.37			A zxAnEnvCardNearCriticalTempClr trap is sent when the zxAnEnvCardNearCriticalTempAlm is cleared.
NTF zxAnEnvOptNearCriticalTempAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.38			A zxAnEnvOptNearCriticalTempAlm trap is sent when the optical module temperature is close to the optical module critical temperature alarm threshold.
NTF zxAnEnvOptNearCriticalTempClr	1.3.6.1.4.1.3902.1082.10.10.3.1.39			A zxAnEnvOptNearCriticalTempClr trap is sent when the zxAnEnvOptNearCriticalTempAlm is cleared.
NTF zxAnEnvHeatRadiationAbnormalAlm	1.3.6.1.4.1.3902.1082.10.10.3.1.40			A zxAnEnvHeatRadiationAbnormalAlm trap is sent when the temperature difference between the card and the environment exceeds the zxAnCardHeatRadiationAlmThresh.
NTF zxAnEnvHeatRadiationAbnormalClr	1.3.6.1.4.1.3902.1082.10.10.3.1.41			A zxAnEnvHeatRadiationAbnormalClr trap is sent when the zxAnEnvHeatRadiationAbnormalAlm is cleared.
zxAnEnvMonInterfaceTraps	1.3.6.1.4.1.3902.1082.10.10.3.2
NTF zxAnEnvMonitorInterfaceLinkDown	1.3.6.1.4.1.3902.1082.10.10.3.2.1			It indicates that the agent has detected that the link at the environment monitoring interface has been down.
NTF zxAnEnvMonitorInterfaceLinkUp	1.3.6.1.4.1.3902.1082.10.10.3.2.2			It indicates that the agent has detected that the link at the environment monitoring interface has been up.
zxAnEnvMonPowerSupplyTraps	1.3.6.1.4.1.3902.1082.10.10.3.3
NTF zxAnEnvPowerSupplyModuleDown	1.3.6.1.4.1.3902.1082.10.10.3.3.1			It indicates that the power supply module is down.
NTF zxAnEnvPowerSupplyModuleUp	1.3.6.1.4.1.3902.1082.10.10.3.3.2			It indicates that the power supply module is up.
NTF zxAnEnvPowerOverVoltageAlm	1.3.6.1.4.1.3902.1082.10.10.3.3.3			It indicates that the input voltage of power supply is over-voltage.
NTF zxAnEnvPowerOverVoltageClr	1.3.6.1.4.1.3902.1082.10.10.3.3.4			It indicates that the over-voltage fault is cleared.
NTF zxAnEnvPowerUnderVoltageAlm	1.3.6.1.4.1.3902.1082.10.10.3.3.5			It indicates that the input voltage of power supply is under-voltage.
NTF zxAnEnvPowerUnderVoltageClr	1.3.6.1.4.1.3902.1082.10.10.3.3.6			It indicates that the under-voltage fault is cleared.
NTF zxAnEnvPowerOff	1.3.6.1.4.1.3902.1082.10.10.3.3.7			It indicates that the power supply is off.
NTF zxAnEnvPowerOn	1.3.6.1.4.1.3902.1082.10.10.3.3.8			It indicates that the power supply off fault is cleared.
NTF zxAnEnvEmergencyPowerSaveAlm	1.3.6.1.4.1.3902.1082.10.10.3.3.9			The current power supply switches to storage battery, the emergency power saving action has been taken.
NTF zxAnEnvEmergencyPowerSaveClr	1.3.6.1.4.1.3902.1082.10.10.3.3.10			The current power supply switches to normal AC power.
NTF zxAnEnvACPowerDownAlm	1.3.6.1.4.1.3902.1082.10.10.3.3.11			A zxAnEnvACPowerDownAlm trap is sent when the agent detects no AC power input.
NTF zxAnEnvACPowerDownClr	1.3.6.1.4.1.3902.1082.10.10.3.3.12			A zxAnEnvACPowerDownClr trap is sent when the agent detects AC power input.
NTF zxAnEnvNoBatteryAlm	1.3.6.1.4.1.3902.1082.10.10.3.3.13			A zxAnEnvNoBatteryAlm trap is sent when no battery found by the agent.
NTF zxAnEnvNoBatteryClr	1.3.6.1.4.1.3902.1082.10.10.3.3.14			A zxAnEnvNoBatteryClr trap is sent when the battery has been found by the agent.
NTF zxAnEnvBatteryUnderVoltageAlm	1.3.6.1.4.1.3902.1082.10.10.3.3.15			A zxAnEnvBatteryUnderVoltageAlm trap is sent when the battery voltage is under-voltage.
NTF zxAnEnvBatteryUnderVoltageClr	1.3.6.1.4.1.3902.1082.10.10.3.3.16			A zxAnEnvBatteryUnderVoltageClr trap is sent when the battery voltage becomes normal.
zxAnEnvMonFanTraps	1.3.6.1.4.1.3902.1082.10.10.3.4
NTF zxAnEnvFanLinkDown	1.3.6.1.4.1.3902.1082.10.10.3.4.1			It indicates that the agent has detected that fan is offline.
NTF zxAnEnvFanLinkUp	1.3.6.1.4.1.3902.1082.10.10.3.4.2			It indicates that the agent has detected that fan is online.
NTF zxAnEnvFanTrayLinkDown	1.3.6.1.4.1.3902.1082.10.10.3.4.3			It indicates that the agent has detected that the link at the fan card interface has been down.
NTF zxAnEnvFanTrayLinkUp	1.3.6.1.4.1.3902.1082.10.10.3.4.4			It indicates that the agent has detected that the link at the fan card interface has been up.
NTF zxAnEnvFanFailureAlm	1.3.6.1.4.1.3902.1082.10.10.3.4.5			It indicates that the fan is in fault.
NTF zxAnEnvFanFailureClr	1.3.6.1.4.1.3902.1082.10.10.3.4.6			It indicates that the fan's fault is cleared.
zxAnEnvDeviceTraps	1.3.6.1.4.1.3902.1082.10.10.3.5
NTF zxAnEnvDeviceAbnormalAlm	1.3.6.1.4.1.3902.1082.10.10.3.5.1			A zxAnEnvDeviceAbnormalAlm trap is sent when the current status of environment device is inconsistent with normal status.
NTF zxAnEnvDeviceAbnormalClr	1.3.6.1.4.1.3902.1082.10.10.3.5.2			A zxAnEnvDeviceAbnormalClr trap is sent when current status of environment device is consistent with normal status.
zxAnEnvMonConformance	1.3.6.1.4.1.3902.1082.10.10.4
zxAnEnvMonCompliances	1.3.6.1.4.1.3902.1082.10.10.4.1
zxAnEnvMonCompliance	1.3.6.1.4.1.3902.1082.10.10.4.1.1			The compliance statement for SNMP entities which implement the ZTE-AN-ENVMON-MIB.
zxAnEnvMonGroups	1.3.6.1.4.1.3902.1082.10.10.4.2
zxAnEnvMonCapabilitiesGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.1			The collection of objects which are used to represent environment management capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment.
zxAnEnvTempGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.2			The collection of objects which are used to represent the temperature information of this equipment/card and to set the temperature alarm threshold of the environment/card.
zxAnEnvCardTempGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.3			The collection of objects which are used to represent temperature performance of the card environment.
zxAnEnvInterfaceGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.4			The collection of objects which are used to represent the interface connection of the equipment.
zxAnEnvPowerSupplyGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.5			The collection of objects which are used to provide power management functions, include power count and the voltage status of the power supply.
zxAnEnvFanTrayTableGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.6			The collection of objects which are used to provide fan management functions, include setting the speed control mode and the percentage of speed of the different speed level of the fan.
zxAnEnvFanTableGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.7			The collection of objects which are used to provide the speed information and operational status of the fan.
zxAnEnvMonNotificationsGroup	1.3.6.1.4.1.3902.1082.10.10.4.2.8			The notifications which indicate specific changes, include temperature, fan status, power status and gpon card status.

RFC description

Environmental monitoring for ZTE Access Nodes including temperature, power supplies, fans, and environmental protection mechanisms.

Start monitoring ZTE Access Node chassis (temperature/power-supply-voltage/fan-speed threshold status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZTE-AN-ENVMON-MIB