| OID symbolic | OID numeric | Type | Access | Description |
|---|
| zhoneIfMauTable | 1.3.6.1.4.1.5504.5.1.1 | | not-accessible | Table of descriptive and status information
about the phsyical Enet interface. |
| zhoneIfMauEntry | 1.3.6.1.4.1.5504.5.1.1.1 | | not-accessible | An entry in the table, containing information
about a single physical Enet interface. |
| I32 zhoneMauIfIndex | 1.3.6.1.4.1.5504.5.1.1.1.1 | Integer32 | read-only | This variable uniquely identifies the interface
to which the Ethernet/MAU described by this entry
is connected. |
| INT zhoneMauType | 1.3.6.1.4.1.5504.5.1.1.1.2 | INTEGER | read-write | Physical Interface Type |
| INT zhoneMauOperStatus | 1.3.6.1.4.1.5504.5.1.1.1.3 | INTEGER | read-only | The current operational state of the MAU.
other(1) is returned if the MAU or interface is in
a state other than one of the states 2 through 6.
unknown(2) is returned when the true state of the
MAU is unknown; for example, when it is being
initialized.
operational(3) state is fully functional, operates,
and passes signals to its attached DTE.
standby(4) state forces DI and CI to idle and the
media transmitter or interface to idle or fault,
if supported. Standby(4) mode only applies to
link type MAUs. The state of
zhoneMauMediaAvailable is unaffected.
A MAU in shutdown(5) state assumes the same
condition on DI, CI, and the media transmitter
as though it were powered down or not connected.
The MAU MAY return other(1) value for the
zhoneMauJabberState and zhoneMauMediaAvailable
objects when it is in this state. For an AUI,
this state will remove power from the AUI.
Setting this variable to the value reset(6)
resets the MAU in the same manner as a
power-off, power-on cycle of at least one-half
second would. The agent is not required to
return the value reset (6). |
| INT zhoneMauMediaAvailable | 1.3.6.1.4.1.5504.5.1.1.1.4 | INTEGER | read-only | If the MAU or interface is a link or fiber type
(FOIRL, 10BASE-T, 10BASE-F) then this is
equivalent to the link test fail state/low light
function. For an AUI MAU this indicates whether
or not loopback is detected on the DI circuit.
other(1) is returned if the mediaAvailable state
is not one of 2 through 11.
unknown(2) is returned when the MAU's true state
is unknown; for example, when it is being
initialized. At power-up or following a reset,
the value of this attribute will be unknown for
AUI and 10BASE-FP MAUs. For these MAUs loopback
will be tested on each transmission during which
no collision is detected. If DI is receiving input
when DO returns to IDL after a transmission and
there has been no collision during the
transmission then loopback will be detected. The
value of this attribute will only change during
non-collided transmissions for AUI and
10BASE-FP MAUs.
For 100Mbps and 1000Mbps MAUs, the enumerations
match the states within the respective link
integrity states. Any MAU which implements
management of auto-negotiation will map remote
fault indication to remote fault.
available(3) indicates that the link, light, or
loopback is normal. The value notAvailable(4)
indicates link loss, low light, or no loopback.
remoteFault(5) indicates that a fault has been
detected at the remote end of the link. This
value applies to 10BASE-FB, 100BASE-T4 Far End
Fault Indication and non-specified remote
faults from a system running auto-negotiation.
remoteJabber(7), remoteLinkLoss(8), and
remoteTest(9) SHOULD be used instead of
remoteFault(5) where the reason for remote
fault is identified in the remote signaling
protocol.
invalidSignal(6) indicates that an invalid signal
has been received from the other end of the link.
InvalidSignal(6) applies only to MAUs of type
10BASE-FB.
Where an IEEE Std 802.3u-1995 clause 22 MII
is present, a logic one in the remote fault bit
(reference section 22.2.4.2.8 of that document)
maps to the value remoteFault(5), and a logic
zero in the link status bit (reference section
22.2.4.2.10 of that document) maps to the value
notAvailable(4). The value notAvailable(4)
takes precedence over the value remoteFault(5).
Any MAU that implements management of clause 37
Auto-Negotiation will map the received RF1 and
RF2 bit values for Offline to offline(10), Link
Failure to remoteFault(5) and Auto-Negotiation
Error to autoNegError(11). |
| C32 zhoneMauMediaAvailStateExits | 1.3.6.1.4.1.5504.5.1.1.1.5 | Counter32 | read-only | A count of the number of times that
zhoneMauMediaAvailable for this MAU or interface
instance leaves the state available(3).
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime. |
| INT zhoneMauJabberState | 1.3.6.1.4.1.5504.5.1.1.1.6 | INTEGER | read-only | The value other(1) is returned if the jabber
state is not 2, 3, or 4.
unknown(2) is returned when the MAU's true state
is unknown; e.g. when it is being initialized.
If the MAU is not jabbering the agent returns
noJabber(3). This is the 'normal' state.
If the MAU is in jabber state the agent returns
the jabbering(4) value. |
| C32 zhoneMauJabberingStateEnters | 1.3.6.1.4.1.5504.5.1.1.1.7 | Counter32 | read-only | A count of the number of times that
zhoneMauJabberState for this MAU or interface
instance enters the state jabbering(4). This
counter will always indicate zero for MAUs of
ype dot1MauTypeAUI and those of speeds above
10Mbps.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime. |
| C32 zhoneMauFalseCarriers | 1.3.6.1.4.1.5504.5.1.1.1.8 | Counter32 | read-only | A count of the number of false carrier events
during IDLE in 100BASE-X and 1000BASE-X links.
For all other MAU or inetrafce types, this counter
will always indicate zero. This counter does not
increment at the symbol rate.
It can increment after a valid carrier
completion at a maximum rate of once per 100 ms
for 100BASE-X and once per 10us for 1000BASE-X
until the next CarrierEvent.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime. |
| INT zhoneMauDefaultType | 1.3.6.1.4.1.5504.5.1.1.1.9 | INTEGER | read-only | Physical interface type. |
| T/F zhoneMauAutoNegSupported | 1.3.6.1.4.1.5504.5.1.1.1.10 | TruthValue | read-only | This object indicates whether or not
auto-negotiation is supported. |
| BIT zhoneMauTypeListBits | 1.3.6.1.4.1.5504.5.1.1.1.11 | Bits | read-only | A value that uniquely identifies the set of
possible IEEE 802.3 types that the MAU could be.
If auto-negotiation is present on this MAU, this
object will map to ifMauAutoNegCapability.
Note that this MAU may be capable of operating
as a MAU type that is beyond the scope of this
MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for capabilities that are listed above. |
| INT zhoneMauClkSrc | 1.3.6.1.4.1.5504.5.1.1.1.12 | INTEGER | read-write | Clock source for timing.
Unused - unused
Automatic - Master/Slave is decided during autonegotiation
Master - Clocked from local source
Slave - Loop timing from the received data stream |
| INT zhoneMauPauseFlowControl | 1.3.6.1.4.1.5504.5.1.1.1.13 | INTEGER | read-write | When autonegotiation is enabled (zhoneMauAutoNegSupported is true),
this Pause Flow Control field is used to program the advertised
pause capabilities.
When autonegotiation is disabled (manual negotiation), this
Pause Flow Control field is used to program the local Mac
as instructed.
If passthrough is selected the pause frames are sent to the host
for forwarding or discard as the packet rules dictate. |
| INT zhoneMauAggregationMode | 1.3.6.1.4.1.5504.5.1.1.1.14 | INTEGER | read-write | On: The link aggregation is forced to be formed without any
LACP negotiation .In other words, the switch will neither send the
LACP packet nor process any incoming LACP packet. This is similar
to the on state for PAgP.
Off: The link aggregation will not be formed.
We do not send or understand the LACP packet.
This is similar to the off state for PAgP.
Passive: The switch does not initiate the channel,
but does understand incoming LACP packets.
The peer (in active state) initiates negotiation
(by sending out an LACP packet) which we receive and reply to,
eventually forming the aggregation channel with the peer.
This is similar to the auto mode in PAgP.
Active: We are willing to form an aggregate link, and
initiate the negotiation. The link aggregate will be formed
if the other end is running in LACP active or passive mode.
This is similar to the desirable mode of PAgP. |
| NUM zhoneMauLinkStateMirror | 1.3.6.1.4.1.5504.5.1.1.1.15 | InterfaceIndexOrZero | read-write | ifIndex of another physical interface whose link state will be mirrored on
this MAU. This is used to propagate a link fault observed on one physical
interface onto another interface. |
| I32 zhoneMauSetPauseTime | 1.3.6.1.4.1.5504.5.1.1.1.16 | Integer32 | read-write | Used to set the pause interval. Units are in pause_quanta.
Currently not supported. |
| I32 zhoneMauMaxFrameSize | 1.3.6.1.4.1.5504.5.1.1.1.17 | Integer32 | read-write | Used to set the max frame size for ethernet ports.
Units are bytes. Range is 0 15360. 0 is default implying 2048 bytes. |
| I32 zhoneMauIngressRate | 1.3.6.1.4.1.5504.5.1.1.1.18 | Integer32 | read-write | Used to set the ingress rate for ethernet ports.
Units are Kbps. Range is 0 10Gbps. 0 is default implying no limit. |
| I32 zhoneMauIngressBurstSize | 1.3.6.1.4.1.5504.5.1.1.1.19 | Integer32 | read-write | Used to set the ingress burst size for ethernet ports.
Units are Kbits. Range is 0 512000. 0 is default implying no restriction. |
| I32 zhoneMauEgressRate | 1.3.6.1.4.1.5504.5.1.1.1.20 | Integer32 | read-write | Used to set the egress rate for ethernet ports.
Units are Kbps. Range is 0 10Gbps. 0 is default implying no limit. |
| I32 zhoneMauEgressBurstSize | 1.3.6.1.4.1.5504.5.1.1.1.21 | Integer32 | read-write | Used to set the egress burst size for ethernet ports.
Units are Kbits. Range is 0 512000. 0 is default implying no restriction. |
| zhoneMauAutoNegTable | 1.3.6.1.4.1.5504.5.1.2 | | not-accessible | Configuration and status objects for the
auto-negotiation function of MAUs attached to
interfaces. |
| zhoneMauAutoNegEntry | 1.3.6.1.4.1.5504.5.1.2.1 | | not-accessible | An entry in the table, containing configuration
and status information for the auto-negotiation
function of a particular MAU. |
| INT zhoneMauAutoNegAdminStatus | 1.3.6.1.4.1.5504.5.1.2.1.1 | INTEGER | read-write | Setting this object to enabled(1) will cause
the interface which has the auto-negotiation
signaling ability to be enabled.
If the value of this object is disabled(2) then
the interface will act as it would if it had no
auto-negotiation signaling. Under these
conditions, an IEEE 802.3 MAU will immediately
be forced to the state indicated by the value of
the object zhoneMauDefaultType.
NOTE TO IMPLEMENTORS: When
ifMauAutoNegAdminStatus transitions from enabled
to disabled, the agent implementation MUST
ensure that the operational type of the MAU (as
reported by zhoneMauType) correctly transitions
to the value specified by the zhoneMauDefaultType
object, rather than continuing to operate at the
value earlier determined by the auto-negotiation
function. |
| INT zhoneMauAutoNegRemoteSignaling | 1.3.6.1.4.1.5504.5.1.2.1.2 | INTEGER | read-only | A value indicating whether the remote end of
the link is using auto-negotiation signaling. It
takes the value detected(1) if and only if,
during the previous link negotiation, FLP Bursts
were received. |
| INT zhoneMauAutoNegConfig | 1.3.6.1.4.1.5504.5.1.2.1.3 | INTEGER | read-only | A value indicating the current status of the
auto-negotiation process. The enumeration
parallelDetectFail(5) maps to a failure in
parallel detection as defined in 28.2.3.1 of
[IEEE 802.3 Std]. |
| INT zhoneMauAutoNegRestart | 1.3.6.1.4.1.5504.5.1.2.1.4 | INTEGER | read-write | If the value of this object is set to restart(1)
then this will force auto-negotiation to begin
link renegotiation. If auto-negotiation signaling
is disabled, a write to this object
has no effect.
Setting the value of this object to norestart(2)
has no effect. |
| BIT zhoneMauAutoNegCapabilityBits | 1.3.6.1.4.1.5504.5.1.2.1.5 | Bits | read-only | A value that uniquely identifies the set of
capabilities of the local auto-negotiation
entity. Note that interfaces that support this
MIB may have capabilities that extend beyond the
scope of this MIB.
Note that the local auto-negotiation entity may
support some capabilities beyond the scope of
this MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for capabilities that are listed above. |
| BIT zhoneMauAutoNegCapAdvertBits | 1.3.6.1.4.1.5504.5.1.2.1.6 | Bits | read-write | A value that uniquely identifies the set of
capabilities advertised by the local
auto-negotiation entity.
Capabilities in this object that are not
available in ifMauAutoNegCapabilityBits cannot
be enabled.
Note that the local auto-negotiation entity may
advertise some capabilities beyond the scope of
this MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for capabilities that are listed above. |
| BIT zhoneMauAutoNegCapRecvBits | 1.3.6.1.4.1.5504.5.1.2.1.7 | Bits | read-only | A value that uniquely identifies the set of
capabilities received from the remote
auto-negotiation entity.
Note that interfaces that support this MIB may
be attached to remote auto-negotiation entities
which have capabilities beyond the scope of this
MIB. This is indicated by returning the bit
value bOther(0) in addition to any bit values for
capabilities that are listed above. |
| INT zhoneMauAutoNegRemoteFaultAdvert | 1.3.6.1.4.1.5504.5.1.2.1.8 | INTEGER | read-write | A value that identifies any local fault
indications that this MAU has detected and will
advertise at the next auto-negotiation
interaction for 1000Mbps MAUs. |
| INT zhoneMauAutoNegRemoteFaultRecv | 1.3.6.1.4.1.5504.5.1.2.1.9 | INTEGER | read-only | A value that identifies any fault indications
received from the far end of a link by the
local auto-negotiation entity for 1000Mbps
MAUs. |
| zhoneEnetTraps | 1.3.6.1.4.1.5504.5.1.3 | | | Description. |
| enetV2Traps | 1.3.6.1.4.1.5504.5.1.3.0 | | | Description. |
| NTF rprEastSpanTrap | 1.3.6.1.4.1.5504.5.1.3.0.1 | | | Resilient Packet Ring (RPR) East Span Trap - indicates
East span went Up or Down. RPR runs over Gigabit
Ethernet. |
| NTF rprWestSpanTrap | 1.3.6.1.4.1.5504.5.1.3.0.2 | | | Resilient Packet Ring (RPR) West Span Trap - indicates
West span went Up or Down. RPR runs over Gigabit
Ethernet. |
| NTF linkAggLink1Trap | 1.3.6.1.4.1.5504.5.1.3.0.3 | | | Link Aggregation Link1 Trap - indicates
Link 1 went Up or Down. |
| NTF linkAggLink2Trap | 1.3.6.1.4.1.5504.5.1.3.0.4 | | | Link Aggregation Link2 Trap - indicates
Link 2 went Up or Down. |
| rprSpanGroup | 1.3.6.1.4.1.5504.5.1.3.2 | | | Grouping of RPR Span Notifications. |
| linkAggLinkGroup | 1.3.6.1.4.1.5504.5.1.3.3 | | | Grouping of Link Aggregation Link Notifications. |
| zhoneLinkAggTable | 1.3.6.1.4.1.5504.5.1.4 | | not-accessible | Table of Identifiers specifying the partner system to which an aggregation is connected. |
| zhoneLinkAggEntry | 1.3.6.1.4.1.5504.5.1.4.1 | | not-accessible | An entry in the table, containing information
about a single partner system aggregation. |
| I32 zhoneLinkAggIfIndex | 1.3.6.1.4.1.5504.5.1.4.1.1 | Integer32 | read-only | This variable uniquely identifies the link
aggregation by which the profile described
in this entry is identified. |
| OCT zhoneLinkAggPartnerSystem | 1.3.6.1.4.1.5504.5.1.4.1.2 | OCTET STRING | read-only | A six-byte identifier, similar to a MAC address,
specifying the partner system, but stored as a
string, and specified in the pattern
'nn:nn:nn:nn:nn:nn', where 'nn' is a hex number
specifying a byte of the pattern. |
| I32 zhoneLinkAggPartnerSystemPriority | 1.3.6.1.4.1.5504.5.1.4.1.3 | Integer32 | read-only | An integer further specifying the partner system. |
| I32 zhoneLinkAggPartnerGroupId | 1.3.6.1.4.1.5504.5.1.4.1.4 | Integer32 | read-only | An integer identifier specifying the link group. |
| phyEnetMauMib | 1.3.6.1.4.1.5504.6.8 | | | MIB to manage the physical interface on Ethernet
ports. The MAU referred to by the MIB refers to
both integarted physical interfaces as well as
the now rarely used external MAUs.
Adapted from RFC 2668 - Definitions of Managed
Objects for 802.3 Media Attachment Units (MAU). |
