All MIBs › ZHONE-COM-ATM-MIB
Organization: Zhone Technologies, Inc.
Last Updated: 2005-04-05
Category: Zhone Technologies CPE and Access
Description: Manages Zhone Technologies ATM interface configuration, VCC/VPC provisioning, and traffic statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ZHONE-COM-ATM-MIB?
ZHONE-COM-ATM-MIB is a Zhone Technologies enterprise MIB for managing ATM (Asynchronous Transfer Mode) interfaces on Zhone access/broadband equipment, covering VCC/VPC (virtual circuit/path) provisioning and associated traffic statistics. It exposes ATM interface configuration alongside per-circuit cell/traffic counters used to gauge circuit health and utilization. Its monitoring role blends configuration and performance-status visibility: administrators poll VCC/VPC provisioning state to confirm circuits are correctly established, and watch traffic statistics such as cell counts and discards to detect a circuit experiencing congestion or errors that would degrade the ATM-carried service, often DSL backhaul. It builds on ITU-T/ATM Forum ATM standards and typically complements the IETF ATM MIB (RFC 2515) rather than replacing it. It is deployed on Zhone DSLAM/broadband access equipment where ATM virtual circuits carry subscriber traffic and need ongoing health monitoring. Engineers can download the ZHONE-COM-ATM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ZHONE-COM-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Zhone DSLAM/broadband access equipment (ATM-based)
Monitoring Examples
An administrator would poll the ATM interface's VCC/VPC provisioning table to confirm a given virtual circuit is in the expected active state, then check its traffic statistics counters for rising cell-discard counts that would indicate congestion or a misconfigured traffic contract. Comparing statistics across multiple VCCs on the same physical ATM interface helps isolate whether a problem is circuit-specific or affects the whole interface. Because no sample objects were captured for this MIB, exact object/table names cannot be confirmed beyond what the short description indicates.
What Can Be Monitored
- VCC/VPC provisioning state
- ATM cell traffic statistics
- circuit cell-discard/error counts
This MIB depends on
Related MIBs
Imported Objects
From ATM-MIB
| atmInterfaceDs3PlcpAlarmState | OBJECT-TYPE |
| atmInterfaceTCAlarmState | OBJECT-TYPE |
| atmInterfaceTCEntry | OBJECT-TYPE |
| atmTrafficDescrParamEntry | OBJECT-TYPE |
| atmVcCrossConnectEntry | OBJECT-TYPE |
| atmVccAal5CpcsReceiveSduSize | OBJECT-TYPE |
| atmVccAal5CpcsTransmitSduSize | OBJECT-TYPE |
| atmVccAal5EncapsType | OBJECT-TYPE |
| atmVccAalType | OBJECT-TYPE |
| atmVclAdminStatus | OBJECT-TYPE |
| atmVclCastType | OBJECT-TYPE |
| atmVclConnKind | OBJECT-TYPE |
| atmVclCrossConnectIdentifier | OBJECT-TYPE |
| atmVclEntry | OBJECT-TYPE |
| atmVclLastChange | OBJECT-TYPE |
| atmVclOperStatus | OBJECT-TYPE |
| atmVclReceiveTrafficDescrIndex | OBJECT-TYPE |
| atmVclRowStatus | OBJECT-TYPE |
| atmVclTransmitTrafficDescrIndex | OBJECT-TYPE |
| atmVclVci | OBJECT-TYPE |
| atmVclVpi | OBJECT-TYPE |
| atmVplAdminStatus | OBJECT-TYPE |
| atmVplCastType | OBJECT-TYPE |
| atmVplConnKind | OBJECT-TYPE |
| atmVplCrossConnectIdentifier | OBJECT-TYPE |
| atmVplEntry | OBJECT-TYPE |
| atmVplLastChange | OBJECT-TYPE |
| atmVplOperStatus | OBJECT-TYPE |
| atmVplReceiveTrafficDescrIndex | OBJECT-TYPE |
| atmVplRowStatus | OBJECT-TYPE |
| atmVplTransmitTrafficDescrIndex | OBJECT-TYPE |
| atmVplVpi | OBJECT-TYPE |
From ATM-TC-MIB
| AtmVcIdentifier | |
| AtmVpIdentifier |
From IF-MIB
| InterfaceIndex | |
| ifIndex | OBJECT-TYPE |
From SNMPv2-CONF
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| TruthValue |
From Zhone
| zhoneAtm | OBJECT-IDENTITY |
| zhoneModules | OBJECT-IDENTITY |
| zhoneShelfIndex | OBJECT-TYPE |
| zhoneSlotIndex | OBJECT-TYPE |
From Zhone-TC
| ZhoneAdminString | |
| ZhoneRowStatus |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF atmDsx3PlcpAlarmStatusChange | 1.3.6.1.4.1.5504.4.2.2.2.0.2 | This trap indicates if there is an alarm present for the DS3 PLCP. | ||
| NTF atmInterfaceTCAlarmStateChange | 1.3.6.1.4.1.5504.4.2.2.2.0.3 | This trap indicates that there is an alarm present for the TC Sublayer. | ||
| NTF atmOamF4PingStatus | 1.3.6.1.4.1.5504.4.2.2.2.0.8 | A notification is sent when the OAM F4 Ping succeeds or fails. The entity is identified by its ifIndex, and VPI values in the trap instance OIDs. A status value of true indicates successful Ping, otherwise unsuccessful Ping. | ||
| NTF atmOamF5PingStatus | 1.3.6.1.4.1.5504.4.2.2.2.0.6 | A notification is sent when the OAM F5 Ping succeeds or fails. The entity is identified by its ifIndex, VPI and VCI values in the trap instance OIDs. A status value of true indicates successful Ping, otherwise unsuccessful Ping. | ||
| OID atmVci | 1.3.6.1.4.1.5504.4.2.2.11 | AtmVcIdentifier | accessible-for-notify | VCI used for traps defined under atm traps |
| NTF atmVclBandwidthUnavailable | 1.3.6.1.4.1.5504.4.2.2.2.0.4 | This trap indicates that guranteed bandwidth specified by zhoneAtmTrafficDescrParamExtTrnkVclRate in the traffic descriptor is not available in the system. This is sent when a VCL is activated with the traffic descriptor which specifies higher than available rate or a VCL is activated with the traffic descriptor which specifies the vcl-rate value which can cause available bandwidth to run out. In this trap, shelf/slot is sent as part of the common fields sent in all traps. | ||
| NTF atmVclExtOamF4PingStatus | 1.3.6.1.4.1.5504.4.2.2.2.0.9 | A notification is sent when the VCL OAM F4 Ping succeeds or fails. The entity is identified by its ifIndex, vpi and vci values in the trap instance OIDs. zhoneAtmVclExtOamF4PingStatus value of true indicates successful Ping, otherwise unsuccessful Ping. | ||
| NTF atmVclOperStatusChange | 1.3.6.1.4.1.5504.4.2.2.2.0.1 | A notification is sent when the operational status of an ATM VCL changes. The VCL entity is identified by its ifIndex, VPI and VCI values in the trap instance OIDs. | ||
| atmVclToMulticastMap | 1.3.6.1.4.1.5504.4.2.2.16 | |||
| atmVclToMulticastMapEntry | 1.3.6.1.4.1.5504.4.2.2.16.2.1 | not-accessible | An entry in the Multicast Address to Vcl Mapping table. This entry is used to associate a multicast address with a Vcl. Step-wise Procedures to set up a Multicast Vcl Mapping profile Once the Vcl that carries the video stream is created, the following steps are taken to provision a Multicast Address to Vcl Mapping: (1) The manager obtains a unique atmMulticastAddressVclMapIndex by reading the atmMulticastAddressVclMapIndexNext object. (2) Next, the manager creates a row in the atmMulticastAddressVclMapTable by setting atmMulticastAddressVclMapRowStatus to createAndGo. The agent checks the sanity of the Vcl, domain index, and multicast address. The row creation fails if: - the specified Vcl does not exist, - the specified Vcl is not of the correct type for multicasting, - the routing domain index is outside of the supported range, - the multicast address is not of the correct format. (3) The manager promotes the row in the atmMulticastAddressVclMapTable when the 'set' completes. | |
| NUM atmVclToMulticastMapIfIndex | 1.3.6.1.4.1.5504.4.2.2.16.2.1.4 | InterfaceIndex | read-create | The ifIndex value of the ATM interface for the Vcl carrying a video stream. |
| INT atmVclToMulticastMapIndex | 1.3.6.1.4.1.5504.4.2.2.16.2.1.1 | INTEGER | not-accessible | A unique value to identify this Multicast Address to Vcl mapping. |
| INT atmVclToMulticastMapIndexNext | 1.3.6.1.4.1.5504.4.2.2.16.1 | INTEGER | read-only | This object contains an appropriate value to be used for atmMulticastAddressVclMapIndex when creating entries in the atmMulticastAddressVclMapTable. The value 0 indicates that no unassigned entries are available. To obtain the atmMulticastAddressVclMapIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse. |
| IP atmVclToMulticastMapMulticastAddress | 1.3.6.1.4.1.5504.4.2.2.16.2.1.3 | IpAddress | read-create | Multicast IP address contained in the MPEG2 video stream. |
| INT atmVclToMulticastMapRoutingDomain | 1.3.6.1.4.1.5504.4.2.2.16.2.1.2 | INTEGER | read-create | Routing domain of the Head-End video server. |
| ZHO atmVclToMulticastMapRowStatus | 1.3.6.1.4.1.5504.4.2.2.16.2.1.7 | ZhoneRowStatus | read-create | Row status of the multicast address to Vcl table entry. This object must be initially set to 'createAndGo'. |
| atmVclToMulticastMapTable | 1.3.6.1.4.1.5504.4.2.2.16.2 | not-accessible | The Multicast Address to Vcl Mapping table. Each entry in this table associates a multicast address representing a video stream with a Vcl. All of the entries in this table are assumed to be unique, not only in terms of index, but in terms of (index, multicast address) (ifIndex, vpi, vci). Note that the Vcl type for this table should always be 'other', denoting cell relay pass-through. We are not terminating the IP stream on the MALC. Also note that the Vcls that this table refer to are the ones originating at the Video Head-End, coming into the MALC Uplink card. | |
| OID atmVclToMulticastMapVci | 1.3.6.1.4.1.5504.4.2.2.16.2.1.6 | AtmVcIdentifier | read-create | The VCI value of the ATM interface for the Vcl carrying a video stream. |
| OID atmVclToMulticastMapVpi | 1.3.6.1.4.1.5504.4.2.2.16.2.1.5 | AtmVpIdentifier | read-create | The VPI value of the ATM interface for the Vcl carrying a video stream. |
| OID atmVpi | 1.3.6.1.4.1.5504.4.2.2.10 | AtmVpIdentifier | accessible-for-notify | VPI used for traps defined under atm traps |
| NTF atmVpiAutoCreateComplete | 1.3.6.1.4.1.5504.4.2.2.2.0.7 | Notification indicating Vpi auto creation is complete. | ||
| I32 atmVpiAutoCreateCount | 1.3.6.1.4.1.5504.4.2.2.13 | Integer32 | accessible-for-notify | This value is the count of the number of auto-created Vpis. |
| T/F atmVpiAutoCreateDone | 1.3.6.1.4.1.5504.4.2.2.12 | TruthValue | accessible-for-notify | Indicates automatic Vpi generation complete. |
| NTF atmVplOperStatusChange | 1.3.6.1.4.1.5504.4.2.2.2.0.5 | Description. | ||
| comAtmExtension | 1.3.6.1.4.1.5504.6.25 | This is the Zhone module identifier for the Zhone ATM MIB extension module. | ||
| I32 zhoneAtmConnectionsAllocated | 1.3.6.1.4.1.5504.4.2.2.8.1.2 | Integer32 | read-only | The total allocated ATM connections for a particular shelf/slot. For a particular VPI, we calculate the number of connections allocated by the following rule: A VP Switched VPI has a Max VCI of 0 and uses 3 connections. A VC Switched VPI has a Max VCI of n (the number n is a power of 2 and is user selected) and uses n connections. The sum of all allocated connections for all VPIs on the selected shelf/slot is the number returned for this value. |
| I32 zhoneAtmConnectionsAvailable | 1.3.6.1.4.1.5504.4.2.2.8.1.1 | Integer32 | read-only | The total available ATM connections for a particular shelf/slot. This number is hardware dependent. Whenever a VPI is allocated for a particular shelf/slot, the number of connections allocated for that VPI is subtracted from the total available and is returned in this value. |
| zhoneAtmConnectionStatsEntry | 1.3.6.1.4.1.5504.4.2.2.8.1 | not-accessible | An entry based on shelf/slot which describes the total allocated and available ATM connections for that shelf/slot. | |
| zhoneAtmConnectionStatsGroup | 1.3.6.1.4.1.5504.4.2.2.3.7 | Description. | ||
| zhoneAtmConnectionStatsTable | 1.3.6.1.4.1.5504.4.2.2.8 | not-accessible | Table which describes the allocated and available ATM connections on a Zhone device. | |
| zhoneAtmExtension | 1.3.6.1.4.1.5504.4.2.2 | This is the Zhone extension MIB tree to the standard ATM defined by rfc2515. | ||
| zhoneAtmGroups | 1.3.6.1.4.1.5504.4.2.2.3 | Zhone ATM object groups and notification groups will be defined under this object identity. | ||
| C32 zhoneAtmInterfaceFeHECEvents | 1.3.6.1.4.1.5504.4.2.2.19.1.5 | Counter32 | read-only | The number of times Far-end Header Error Control (HEC) violations occur. |
| C32 zhoneAtmInterfaceFeNCDEvents | 1.3.6.1.4.1.5504.4.2.2.19.1.4 | Counter32 | read-only | The number of times Far-end No Cell Delineation (NCD) events occur. |
| C32 zhoneAtmInterfaceFeOCDEvents | 1.3.6.1.4.1.5504.4.2.2.19.1.3 | Counter32 | read-only | The number of times Far-end Out of Cell Delineation (OCD) events occur. |
| C32 zhoneAtmInterfaceHECEvents | 1.3.6.1.4.1.5504.4.2.2.19.1.2 | Counter32 | read-only | The number of times Near-end Header Error Control (HEC) violations occur. |
| C32 zhoneAtmInterfaceNCDEvents | 1.3.6.1.4.1.5504.4.2.2.19.1.1 | Counter32 | read-only | The number of times the Near-end No Cell Delineation (NCD) events occur. |
| zhoneAtmInterfaceTcExtEntry | 1.3.6.1.4.1.5504.4.2.2.19.1 | not-accessible | This list contains TC Sublayer parameters and state variables at the ATM interface and is indexed by the ifIndex value of the ATM interface. | |
| zhoneAtmInterfaceTcExtTable | 1.3.6.1.4.1.5504.4.2.2.19 | not-accessible | This table contains ATM interface TC Sublayer parameters and state variables, one entry per ATM interface port. | |
| zhoneAtmPonExtEntry | 1.3.6.1.4.1.5504.4.2.2.17.1 | not-accessible | This is an entry in the Atm PON Extension table. | |
| zhoneAtmPonExtTable | 1.3.6.1.4.1.5504.4.2.2.17 | not-accessible | This is the Zhone extension to the Atm Vcl Table (rfc2515.) It contains APON-related objects. | |
| zhoneAtmPonGroup | 1.3.6.1.4.1.5504.4.2.2.3.9 | Description. | ||
| zhoneAtmStatsExtEntry | 1.3.6.1.4.1.5504.4.2.2.5.1 | not-accessible | Definitions of Forward and Backward: Internal to ATM Switch Fabric ============================================================= |Ext|==>IngressFwd==>| |==>EgressFwd====>|Int| PortPhy|VC | |APC Switch Fabric| |VC |Bus/SAR/DSP | |<==EgressBack<==| |<==IngressBack<==| | Phy ============================================================= | |
| zhoneAtmStatsExtTable | 1.3.6.1.4.1.5504.4.2.2.5 | not-accessible | These statistics values are coming from fabric interface. | |
| zhoneAtmStatsExtTableGroup | 1.3.6.1.4.1.5504.4.2.2.3.4 | Description. | ||
| C64 zhoneAtmStatsTotalFabricCellsRx | 1.3.6.1.4.1.5504.4.2.2.5.1.2 | Counter64 | read-only | Total Cells Recevied at Fabric.Total cells received across the fabric interface for a given VC, including cells discarded due to parity errors. |
| C64 zhoneAtmStatsTotalFabricCellsTx | 1.3.6.1.4.1.5504.4.2.2.5.1.6 | Counter64 | read-only | Total cells transmitted at fabric interace.Total cells transmitted across the fabric interface for a given VC, including cells discarded due to parity errors. |
| C64 zhoneAtmStatsTotalFinalCLP0CellsRx | 1.3.6.1.4.1.5504.4.2.2.5.1.3 | Counter64 | read-only | Total CLP0 Cells received by fabric. This field is setup to monitor egress total cells transmitted CLP0. |
| C64 zhoneAtmStatsTotalFinalCLP0CellsTx | 1.3.6.1.4.1.5504.4.2.2.5.1.7 | Counter64 | read-only | Total CLP0 Cells Transmitted. This field is setup to monitor egress total cells transmitted CLP0. |
| C64 zhoneAtmStatsTotalFinalCLP1CellsRx | 1.3.6.1.4.1.5504.4.2.2.5.1.4 | Counter64 | read-only | Total CLP1 Cells received by fabric. This field is setup to monitor egress total cells transmitted CLP1. |
| C64 zhoneAtmStatsTotalFinalCLP1CellsTx | 1.3.6.1.4.1.5504.4.2.2.5.1.8 | Counter64 | read-only | Total CLP1 Cells Transmitted. This field is setup to monitor egress total cells transmitted CLP1. |
| C64 zhoneAtmStatsTotalInitialCellsRx | 1.3.6.1.4.1.5504.4.2.2.5.1.1 | Counter64 | read-only | Total Initial Cells Received. Total cells received across the ingress interface for a given VC, and not discarded by policing prior to thresholding (includes CPU insertions but excludes Atm switch fabric generated ingress OAM insertions). |
| C64 zhoneAtmStatsTotalInitialCellsTx | 1.3.6.1.4.1.5504.4.2.2.5.1.5 | Counter64 | read-only | Initial Total Cells Transmitted. Total cells transmitted. across the ingress interface for a given VC, and not discarded by policing prior to thresholding (includes CPU insertions but excludes Atm switch fabric generated ingress OAM insertions). |
| I32 zhoneAtmTrafficDescrParamExtCacDivider | 1.3.6.1.4.1.5504.4.2.2.4.1.2 | Integer32 | read-write | This object allows users to oversubsribe. The rate subtracted from CAC is PCR or SCR divided by this object. |
| zhoneAtmTrafficDescrParamExtEntry | 1.3.6.1.4.1.5504.4.2.2.4.1 | not-accessible | This is extension of AtmTrafficDescrParamEntry defined in rfc2515. | |
| zhoneAtmTrafficDescrParamExtGroup | 1.3.6.1.4.1.5504.4.2.2.3.3 | A collection of objects contained in the zhoneAtmTrafficDescrParamExtTable. | ||
| zhoneAtmTrafficDescrParamExtTable | 1.3.6.1.4.1.5504.4.2.2.4 | not-accessible | Zhone extension table for the atmTrafficDescrParamTable defined in rfc2515. | |
| INT zhoneAtmTrafficDescrParamExtTrnkVclRate | 1.3.6.1.4.1.5504.4.2.2.4.1.1 | INTEGER | read-create | This field is used to describe the minimum guaranteed rate for a VCL which is bound to this traffic descriptor for BAN ATM Trunk Cards. It is applicable only for RTVBR service category. Unlike switched voice calls in the TDM world we cannot oversubscribe bandwidth because all of our voice calls must be connected at all times so that we can receive signaling to tell us that the phone when off hook. Instead of oversubscribing we suggest that the service provide under provision their voice calls. An example of this would be a normal good quality voice call over ATM requires about 80kb of bandwidth. To share the bandwidth resource over several customers the service provider would instead allocate (for example) rate16K for a single voice channel, this would allow 5 channels to share the bandwidth required to connect a good quality voice call. Any value less than rate80K could be used if the service provider wished to share bandwidth resources over more than one voice call. In order for this method to produce a good quality voice call enough bandwidth must be unallocated and used in a shared pool by all connections. When the buffering is not adequate for a good quality call the connection will not terminate, instead the call quality will suffer. Values greater than rate80K would be used by devices like a PBX. For all service categories other than RTVBR, unused is the only valid value.For RTVBR unused is not a valid value and one of the rates has to be specified. This parameter is used independently for transmit and receive traffic based on the traffic descriptor specified for transmit and receive in the VCL. Changing this parameter may cause a trap if newly utilized bandwidth for a card exceeds its available bandwidth. It may happen on multiple cards and therefore there can be multiple traps. |
| T/F zhoneAtmTrafficDescrParamExtUsageParameterControl | 1.3.6.1.4.1.5504.4.2.2.4.1.3 | TruthValue | read-create | If set to 'false', this object disables polcing. |
| zhoneAtmTraps | 1.3.6.1.4.1.5504.4.2.2.2 | All the Zhone ATM traps will be defined under this OID. | ||
| zhoneAtmTrapsGroup | 1.3.6.1.4.1.5504.4.2.2.3.2 | A collection of notification traps under the zhoneAtmV2Traps. | ||
| zhoneAtmV2Traps | 1.3.6.1.4.1.5504.4.2.2.2.0 | This object identity adds a zero(0) for the next to last sub-identifier which should be used for new SNMPv2 Traps. | ||
| zhoneAtmVcCrossConnectExtEntry | 1.3.6.1.4.1.5504.4.2.2.20.1 | not-accessible | This list contains Atm Vc Cross Connect Extensions to the atmVcCrossConnectEntry. | |
| OCT zhoneAtmVcCrossConnectExtHandleId | 1.3.6.1.4.1.5504.4.2.2.20.1.1 | OCTET STRING | read-create | An administratively-assigned name for the Atm Vc Cross Connect indicated by the INDEX value. |
| zhoneAtmVcCrossConnectExtTable | 1.3.6.1.4.1.5504.4.2.2.20 | not-accessible | This Table contains Atm Vc Cross Connect Extensions to the atmVcCrossConnectEntry. | |
| zhoneAtmVclExtEntry | 1.3.6.1.4.1.5504.4.2.2.1.1 | not-accessible | An entry in the atmVclExtTable. atmVclExtEntry is an augmentation to the atmVclEntry defined in rfc2515. | |
| INT zhoneAtmVclExtFaultDetectionType | 1.3.6.1.4.1.5504.4.2.2.1.1.1 | INTEGER | read-create | This is used to configure VCL fault detection. The valid values are: * disabled - Fault detection is disabled. This is the default. * oamF5Loopback - This option uses standard OAM fault management cells as defined in ITU.610 for fault detection. Automatic loopback diagnostic cells are sent to the IAD. When fault detection is enabled, atmVclOperStatusChange notification trap is used to indicate to the NMS station an VCL has gone down or has come back up. |
| zhoneAtmVclExtGroup | 1.3.6.1.4.1.5504.4.2.2.3.1 | A collection of objects contained in the zhoneAtmVclExtTable. | ||
| INT zhoneAtmVclExtOamF4Ping | 1.3.6.1.4.1.5504.4.2.2.1.1.5 | INTEGER | read-create | This is used to send a OAM F4 loopback cell for fault detection. The value will automatically revert to disabled after the set is complete. The valid values are: * disabled - OAM F4 loopback cell is not being sent. This is the default. * endToEnd - This option uses standard OAM fault management cells as defined in ITU.610 for fault detection. Setting this will send a OAM F4 end-to-end loopback cell to be sent * segment - This is not supported at this time |
| T/F zhoneAtmVclExtOamF4PingStatus | 1.3.6.1.4.1.5504.4.2.2.1.1.6 | TruthValue | accessible-for-notify | TRUE if ping was successfull and FALSE if failed. |
| INT zhoneAtmVclExtOamF5Ping | 1.3.6.1.4.1.5504.4.2.2.1.1.2 | INTEGER | read-create | This is used to send a OAM F5 loopback cell for fault detection. The value will automatically revert to disabled after the set is complete. The valid values are: * disabled - OAM F5 loopback cell is not being sent. This is the default. * endToEnd - This option uses standard OAM fault management cells as defined in ITU.610 for fault detection. Setting this will send a OAM F5 end-to-end loopback cell to be sent * segment - This is not supported at this time |
| T/F zhoneAtmVclExtOamF5PingStatus | 1.3.6.1.4.1.5504.4.2.2.1.1.3 | TruthValue | accessible-for-notify | TRUE if ping was successfull and FALSE if failed |
| zhoneAtmVclExtTable | 1.3.6.1.4.1.5504.4.2.2.1 | not-accessible | Zhone extension table for the atmVclTable defined in rfc2515. | |
| I32 zhoneAtmVclExtTrafficContainerIndex | 1.3.6.1.4.1.5504.4.2.2.1.1.4 | Integer32 | read-create | Index number of a PON traffic container associated with a VCL definition. |
| zhoneAtmVclMulticastGroup | 1.3.6.1.4.1.5504.4.2.2.3.10 | Description. | ||
| I32 zhoneAtmVclPonTrafficContainerIndex | 1.3.6.1.4.1.5504.4.2.2.17.1.1 | Integer32 | read-create | This field is an index into the ATM PON Traffic Container table. It associated a Vcl with a Traffic Container, and is used to retrieve PON channel provisioning information. |
| zhoneAtmVclRateExtParam | 1.3.6.1.4.1.5504.4.2.2.6 | This is the Zhone extension MIB tree to the ATM VCL rates. | ||
| I32 zhoneAtmVclRateExtParam1 | 1.3.6.1.4.1.5504.4.2.2.6.1 | Integer32 | read-write | This field is used to describe the first least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. It is applicable only for RTVBR/NRTVBR or CBR service category. For RTVBR/NRTVBR service category, this value can be set in the rfc2515 td_param2 of the traffice descriptor table. For CBR service category, this value can be set in the td_param1 field. The maximum rates capacitiy is 16, any value which is not matched in any one of those 16 rates will be rejected. Unlike switched voice calls in the TDM world we cannot oversubscribe bandwidth because all of our voice calls must be connected at all times so that we can receive signaling to tell us that the phone when off hook. Instead of oversubscribing we suggest that the service provide under provision their voice calls. An example of this would be a normal good quality voice call over ATM requires about 189 CPS. To share the bandwidth resource over several customers the service provider would instead allocate (for example) 38 CPS for a single voice channel, this would allow 5 channels to share the bandwidth required to connect a good quality voice call. Any value less than 189 CPS could be used if the service provider wished to share bandwidth resources over more than one voice call. In order for this method to produce a good quality voice call enough bandwidth must be unallocated and used in a shared pool by all connections. When the buffering is not adequate for a good quality call the connection will not terminate, instead the call quality will suffer. Values greater than 189 CPS would be used by devices like a PBX. This parameter is used independently for transmit and receive traffic based on the traffic descriptor specified for transmit and receive in the VCL. |
| I32 zhoneAtmVclRateExtParam10 | 1.3.6.1.4.1.5504.4.2.2.6.10 | Integer32 | read-write | This field is used to describe the tenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam10Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.26 | Integer32 | read-write | This field is used to describe the tenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam11 | 1.3.6.1.4.1.5504.4.2.2.6.11 | Integer32 | read-write | This field is used to describe the eleventh least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam11Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.27 | Integer32 | read-write | This field is used to describe the eleventh least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam12 | 1.3.6.1.4.1.5504.4.2.2.6.12 | Integer32 | read-write | This field is used to describe the twelfth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam12Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.28 | Integer32 | read-write | This field is used to describe the twelfth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam13 | 1.3.6.1.4.1.5504.4.2.2.6.13 | Integer32 | read-write | This field is used to describe the thirteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam13Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.29 | Integer32 | read-write | This field is used to describe the thirteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam14 | 1.3.6.1.4.1.5504.4.2.2.6.14 | Integer32 | read-write | This field is used to describe the fouthteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam14Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.30 | Integer32 | read-write | This field is used to describe the fourteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam15 | 1.3.6.1.4.1.5504.4.2.2.6.15 | Integer32 | read-write | This field is used to describe the fifteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam15Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.31 | Integer32 | read-write | This field is used to describe the fifthteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam16 | 1.3.6.1.4.1.5504.4.2.2.6.16 | Integer32 | read-write | This field is used to describe the sixteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam16Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.32 | Integer32 | read-write | This field is used to describe the sixthteenth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam1Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.17 | Integer32 | read-write | This field is used to describe the first least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam2 | 1.3.6.1.4.1.5504.4.2.2.6.2 | Integer32 | read-write | This field is used to describe the second least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam2Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.18 | Integer32 | read-write | This field is used to describe the second least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam3 | 1.3.6.1.4.1.5504.4.2.2.6.3 | Integer32 | read-write | This field is used to describe the third least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam3Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.19 | Integer32 | read-write | This field is used to describe the third least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam4 | 1.3.6.1.4.1.5504.4.2.2.6.4 | Integer32 | read-write | This field is used to describe the fourth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam4Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.20 | Integer32 | read-write | This field is used to describe the fourth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam5 | 1.3.6.1.4.1.5504.4.2.2.6.5 | Integer32 | read-write | This field is used to describe the fifth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam5Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.21 | Integer32 | read-write | This field is used to describe the fifth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam6 | 1.3.6.1.4.1.5504.4.2.2.6.6 | Integer32 | read-write | This field is used to describe the sixth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam6Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.22 | Integer32 | read-write | This field is used to describe the sixth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam7 | 1.3.6.1.4.1.5504.4.2.2.6.7 | Integer32 | read-write | This field is used to describe the seventh least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam7Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.23 | Integer32 | read-write | This field is used to describe the seventh least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam8 | 1.3.6.1.4.1.5504.4.2.2.6.8 | Integer32 | read-write | This field is used to describe the eighth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam8Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.24 | Integer32 | read-write | This field is used to describe the eighth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam9 | 1.3.6.1.4.1.5504.4.2.2.6.9 | Integer32 | read-write | This field is used to describe the ninth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| I32 zhoneAtmVclRateExtParam9Grp2 | 1.3.6.1.4.1.5504.4.2.2.6.25 | Integer32 | read-write | This field is used to describe the ninth least field of total 16 minimum guaranteed rate which is configurable by user for a VCL which is bound to this traffic descriptor for BAN ATM Trunk or MALC uplink Cards. |
| zhoneAtmVclRateExtParamGroup | 1.3.6.1.4.1.5504.4.2.2.3.5 | Atm Vcl rate parameter values. | ||
| zhoneAtmVpiEntry | 1.3.6.1.4.1.5504.4.2.2.9.1 | not-accessible | An entry based on ifIndex/vpi (which resolves to a particular shelf/slot/port/subport/type/vpi) which contains the maximum VCI value and the switch mode (either vp or vc switched) for a particular VPI. | |
| zhoneAtmVpiGroup | 1.3.6.1.4.1.5504.4.2.2.3.8 | Description. | ||
| I32 zhoneAtmVpiMaxVci | 1.3.6.1.4.1.5504.4.2.2.9.1.1 | Integer32 | read-write | For the selected VPI, this value contains the maximum VCI. For vp switched VPIs, this value must be zero. For vc switched VPIs, this value must be a power of 2 with its maximum value being hardware dependent. |
| I32 zhoneAtmVpiMaxVciPerVp | 1.3.6.1.4.1.5504.4.2.2.9.1.6 | Integer32 | read-write | If vp-switched, but VG connection is vc-switched, this specifies max number of vci on gateway. |
| INT zhoneAtmVpiOamF4Ping | 1.3.6.1.4.1.5504.4.2.2.9.1.4 | INTEGER | read-write | This is used to send a OAM F4 loopback cell for fault detection. The value will automatically revert to disabled after the set is complete. The valid values are: * disabled - OAM F4 loopback cell is not being sent. This is the default. * endToEnd - This option uses standard OAM fault management cells as defined in ITU.610 for fault detection. Setting this will send a OAM F4 end-to-end loopback cell to be sent * segment - This is not supported at this time |
| T/F zhoneAtmVpiOamF4PingStatus | 1.3.6.1.4.1.5504.4.2.2.9.1.5 | TruthValue | accessible-for-notify | TRUE if ping was successfull and FALSE if failed. |
| ZHO zhoneAtmVpiRowStatus | 1.3.6.1.4.1.5504.4.2.2.9.1.3 | ZhoneRowStatus | read-create | Row Status only supports create-and-go and destroy actions. Returns active if row is in service. |
| INT zhoneAtmVpiSwitched | 1.3.6.1.4.1.5504.4.2.2.9.1.2 | INTEGER | read-write | For the selected VPI, this value can be set to either vp switched or vc switched. If it is vp switched, then the max vci must be zero. If it is vc switched, the max vci value must be a power of 2 with its maximum value being hardware dependent. |
| zhoneAtmVpiTable | 1.3.6.1.4.1.5504.4.2.2.9 | not-accessible | Table which describes attributes associated to a particular VPI. Anytime you add to, delete from or modify any entry in this table, you must reboot the card in order for these changes to take effect. The reason for this is that the APC must be re-programmed and the only way to do this is by doing a reboot. In addition, you will not be allowed to modify, create or delete any atm-vcl entry which is on the same card as the VPI until after the card has been rebooted. | |
| zhoneAtmVplExtEntry | 1.3.6.1.4.1.5504.4.2.2.7.1 | not-accessible | NOT CURRENTLY IMPLEMENTED. An entry in the atmVplExtTable. atmVplExtEntry is an augmentation to the atmVplEntry defined in rfc2515. | |
| INT zhoneAtmVplExtFaultDetectionType | 1.3.6.1.4.1.5504.4.2.2.7.1.1 | INTEGER | read-create | NOT CURRENTLY IMPLEMENTED. This is used to configure VPL fault detection. The valid values are: * disabled - Fault detection is disabled. This is the default. * oamF4Loopback - This option uses standard OAM fault management cells as defined in ITU.610 for fault detection. Automatic loopback diagnostic cells are sent to the IAD. When fault detection is enabled, atmVplOperStatusChange notification trap is used to indicate to the NMS station that a VPL has gone down or has come back up. |
| zhoneAtmVplExtGroup | 1.3.6.1.4.1.5504.4.2.2.3.6 | Description. | ||
| zhoneAtmVplExtTable | 1.3.6.1.4.1.5504.4.2.2.7 | not-accessible | Zhone extension table for the atmVplTable defined in rfc2515. | |
| I32 zhoneAtmVplExtTrafficContainerIndex | 1.3.6.1.4.1.5504.4.2.2.7.1.2 | Integer32 | read-create | Index number of a PON traffic container associated with a VPL definition. NOTE: MULTIPLE VARBINDS ACROSS THE VPL TABLE AND THE VPL EXTENSI0N TABLE ARE NOT ALLOWED! It turns out that anyone trying to set just the traffic container index would inadvertantly try to create a Vpl with default settings. To set the traffic container field, the Vpl must be created first. |
| zhoneAtmVplPonExtEntry | 1.3.6.1.4.1.5504.4.2.2.18.1 | not-accessible | This is an entry in the Atm PON Extension table. | |
| zhoneAtmVplPonExtTable | 1.3.6.1.4.1.5504.4.2.2.18 | not-accessible | This is the Zhone extension to the Atm Vpl Table (rfc2515.) It contains APON-related objects. | |
| I32 zhoneAtmVplPonTrafficContainerIndex | 1.3.6.1.4.1.5504.4.2.2.18.1.1 | Integer32 | read-create | This field is an index into the ATM PON Traffic Container table. It associated a Vpl with a Traffic Container, and is used to retrieve PON channel provisioning information. |
RFC description
Zhone Technologies proprietary MIB defining ATM-related objects for management of Zhone networking equipment supporting ATM protocols.
Start monitoring Zhone DSLAM/broadband access equipment, ATM-based (VCC/VPC provisioning, cell-traffic status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.