| OID symbolic | OID numeric | Type | Access | Description |
|---|
| wwpLeosNtpClientMIB | 1.3.6.1.4.1.6141.2.60.18 | | | This MIB module defines the managed objects
for the NTP client on LEOS based WWP devices. |
| wwpLeosNtpClientMIBObjects | 1.3.6.1.4.1.6141.2.60.18.1 | | | |
| wwpLeosNtpClient | 1.3.6.1.4.1.6141.2.60.18.1.1 | | | |
| INT wwpLeosNtpClientState | 1.3.6.1.4.1.6141.2.60.18.1.1.1 | INTEGER | read-write | Setting this object to 'enable' will enable the
NTP client on Ciena devices. |
| INT wwpLeosNtpClientMode | 1.3.6.1.4.1.6141.2.60.18.1.1.2 | INTEGER | read-write | Setting this object to 'broadcast' will cause the
client not to poll the NTP server at all. Instead, it
will wait for configured NTP servers to broadcast
their current time. When the client receives the first
message, it will retrieve a reliable time from that
server. If it is set to polling then device will
poll the NTP server. |
| I32 wwpLeosNtpClientPollFreq | 1.3.6.1.4.1.6141.2.60.18.1.1.3 | Integer32 | read-write | The polling frequency at which NTP server will be polled
if the NTP client is configured to be in polling mode.
The value of this object should be multiple of 16.
The change in the NTP mode will only be effective
when NTP client is enabled and should not be set at
the same time either Min or Max polling frequency is set. |
| wwpLeosNtpClientTable | 1.3.6.1.4.1.6141.2.60.18.1.1.4 | | not-accessible | Table of NTP server information indexed by wwpLeosNtpServerIndex.
To create an entry in the table, use SNMP multiple set operation
and following objects must be set:
wwpLeosNtpServerAddr and wwpLeosNtpServerStatus.
To use MD5 authentication, wwpLeosNtpServerKeyId must be set at the time
of creation along with wwpLeosNtpServerAddr and wwpLeosNtpServerStatus,
otherwise no MD5 authentication will be used. |
| wwpLeosNtpClientEntry | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1 | | not-accessible | An entry for each NTP server. |
| I32 wwpLeosNtpServerIndex | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.1 | Integer32 | not-accessible | Specifies the unique index of the entry. |
| ADR wwpLeosNtpServerAddrType | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.2 | AddressFamilyNumbers | read-write | Specifies the type of address wwpLeosNtpServerAddr belongs to. |
| STR wwpLeosNtpServerAddr | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.3 | DisplayString | read-write | The IP address or host name of the NTP server. |
| IP wwpLeosNtpServerResolvedAddr | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.4 | IpAddress | read-only | Specifies the resolved IP address if wwpLeosNtpServerAddr is set to host name.
If wwpLeosNtpServerAddr is set to IP address then wwpLeosNtpServerResolvedAddr
will be the same as wwpLeosNtpServerAddr.
If the IP address is an IPv6, this OID will be set to 0.0.0.0 and the
wwpLeosNtpServerAddrType will be set to other(0). |
| I32 wwpLeosNtpServerUserPri | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.5 | Integer32 | read-write | This object is no longer implemented as the NTP client determines the server's
relative priority or preference relative to other configured servers. Reads will
always return 1 and writes will be quietly ignored. This object was once used to
specify the user priority of the wwpLeosNtpServerAddr. |
| I32 wwpLeosNtpServerDhcpPri | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.6 | Integer32 | read-only | This object is no longer implemented as the NTP client determines the server's
relative priority or preference relative to other configured servers. Reads will
always return 1 and writes will quietly be ignored. This object was once used to
specify the dhcp priority of the wwpLeosNtpServerAddr. |
| INT wwpLeosNtpServerUserAdminState | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.7 | INTEGER | read-write | This object is used to specify the user admin state of the
wwpLeosNtpServerAddr. |
| INT wwpLeosNtpServerScope | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.8 | INTEGER | read-only | This object is used to specify the scope for the entry.
It specifies if the entry is configured by dhcp/user/both. |
| INT wwpLeosNtpServerOperState | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.9 | INTEGER | read-only | This object is used to specify the operational state of the
wwpLeosNtpServerAddr. |
| ROW wwpLeosNtpServerStatus | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.10 | RowStatus | read-create | To create a row in this table, a manager must
set this object to 'createAndGo'. The server
added will only be effective when NTP client is
enabled.
To create entry in the table use SNMP multiple set operation
and following objects must be set
wwpLeosNtpServerAddr and wwpLeosNtpServerStatus. |
| U32 wwpLeosNtpServerKeyId | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.11 | Unsigned32 | read-write | This object is used to specify the MD5 key ID that that the server
will use. A 0 key ID implies no MD5 key. |
| INT wwpLeosNtpServerState | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.12 | INTEGER | read-only | This object reflects the current connection status of
the server. |
| IPt wwpLeosNtpServerResolvedInetAddrType | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.13 | InetAddressType | read-only | Specifies the type of address wwpLeosNtpServerResolvedInetAddr belongs to.
When set to:
ipv4 : wwpLeosNtpServerResolvedInetAddr should be compliant with
InetAddressIPv4 from RFC 4001
ipv6 : wwpLeosNtpServerResolvedInetAddr should be compliant with
InetAddressIPv6 from RFC 4001. |
| IP wwpLeosNtpServerResolvedInetAddr | 1.3.6.1.4.1.6141.2.60.18.1.1.4.1.14 | InetAddress | read-only | Specifies the resolved IP address if wwpLeosNtpServerAddr is set to host name.
If wwpLeosNtpServerAddr is set to IP address then wwpLeosNtpServerResInetAddr
will be the same as wwpLeosNtpServerAddr.
The InetAddress specified here will be compliant with RFC 4001. |
| wwpLeosNtpAuthTable | 1.3.6.1.4.1.6141.2.60.18.1.1.5 | | not-accessible | The (conceptual) table listing the key-id and MD5 key. |
| wwpLeosNtpAuthEntry | 1.3.6.1.4.1.6141.2.60.18.1.1.5.1 | | not-accessible | An entry (conceptual row) in the wwpLeosNtpAuthTable. |
| U32 wwpLeosNtpAuthKeyId | 1.3.6.1.4.1.6141.2.60.18.1.1.5.1.1 | Unsigned32 | not-accessible | This object specifies the key ID.
It is also used as index in the table. |
| MD5 wwpLeosNtpAuthMd5Key | 1.3.6.1.4.1.6141.2.60.18.1.1.5.1.2 | Md5Key | read-write | Used to specify the MD5 key to use with this key identifier. |
| ROW wwpLeosNtpAuthRowStatus | 1.3.6.1.4.1.6141.2.60.18.1.1.5.1.3 | RowStatus | read-create | To create a row in this table, a manager must
set this object to 'createAndGo'. The server
added will only be effective when NTP client is
enabled.
To create entry in the table use SNMP multiple set operation
and following objects must be set:
wwpLeosNtpAuthKeyId and either wwpLeosNtpAuthMd5Key or wwpLeosNtpAuthMD5KeyEnc. |
| MD5 wwpLeosNtpAuthMD5KeyEnc | 1.3.6.1.4.1.6141.2.60.18.1.1.5.1.4 | Md5Key | read-write | Used to specify the encrypted MD5 key to use with this key identifier. |
| T/F wwpLeosNtpClientMD5State | 1.3.6.1.4.1.6141.2.60.18.1.1.6 | TruthValue | read-write | Set to true to use MD5 authentication for NTP |
| I32 wwpLeosNtpClientDrift | 1.3.6.1.4.1.6141.2.60.18.1.1.7 | Integer32 | read-only | The Drift in micro-seconds of the local clock. This value
is only valid when NTP is enabled and has a valid peer. |
| I32 wwpLeosNtpClientFastOffset | 1.3.6.1.4.1.6141.2.60.18.1.1.9 | Integer32 | read-only | The Fastest Offset seen in micro-seconds of the local clock. This value
is only valid when NTP is enabled and has a valid peer. |
| I32 wwpLeosNtpClientSlowOffset | 1.3.6.1.4.1.6141.2.60.18.1.1.10 | Integer32 | read-only | The Slowest Offset seen in micro-seconds of the local clock. This value
is only valid when NTP is enabled and has a valid peer. |
| I32 wwpLeosNtpClientMinPollFreq | 1.3.6.1.4.1.6141.2.60.18.1.1.11 | Integer32 | read-write | The polling freq at which NTP server will be polled
if the NTP client is configured to be in polling mode
and is not currently synchronized to an NTP server.
The value of this object should be multiple of 16.
The change in the ntp mode will only be affective
when ntp client is enabled and should not be set
at the same time PollFreq is set. |
| I32 wwpLeosNtpClientMaxPollFreq | 1.3.6.1.4.1.6141.2.60.18.1.1.12 | Integer32 | read-write | The polling freq at which NTP server will be polled
if the NTP client is configured to be in polling mode
and is currently synchronized to an NTP server.
The value of this object should be multiple of 16.
The change in the ntp mode will only be affective
when ntp client is enabled and should not be set
at the same time PollFreq is set. |
| I32 wwpLeosNtpClientOffset | 1.3.6.1.4.1.6141.2.60.18.1.1.13 | Integer32 | read-only | When NTP is synchronized, this contains the difference between
the reference clock and the system clock micro-seconds. |
| I32 wwpLeosNtpClientDelay | 1.3.6.1.4.1.6141.2.60.18.1.1.14 | Integer32 | read-only | When NTP is synchronized, this indicates the round trip time
in micro-seconds taken by the reply packet to return in response,
to a query sent by the server. |
| I32 wwpLeosNtpClientJitter | 1.3.6.1.4.1.6141.2.60.18.1.1.15 | Integer32 | read-only | When NTP is synchronized, it indicates the magnitude of
jitter between several time queries in micro-seconds. |
| I32 wwpLeosNtpClientNtpOffset | 1.3.6.1.4.1.6141.2.60.18.1.1.16 | Integer32 | read-only | When NTP is synchronized, this contains the difference between
the reference clock and the system clock micro-seconds. |
| INT wwpLeosNtpClientNtpFastStartMode | 1.3.6.1.4.1.6141.2.60.18.1.1.17 | INTEGER | read-write | Setting this object to 'on' will cause the
NTP client to set it's time to the first reply
received from a synchronized NTP server, the
first time this occurs after the NTP client
is enabled. After that, the normal rules
for selecting and synchronizing to a server
are used. |
| wwpLeosNtpMulticastTable | 1.3.6.1.4.1.6141.2.60.18.1.1.18 | | not-accessible | Table of NTP Multicast Addresses indexed by wwpLeosNtpMulticastIndex.
To create an entry in the table, use SNMP multiple set operation
and following objects must be set:
wwpLeosNtpMulticastInetAddrType and wwpLeosNtpMulticastInetAddr. |
| wwpLeosNtpMulticastEntry | 1.3.6.1.4.1.6141.2.60.18.1.1.18.1 | | not-accessible | An entry for each NTP multicast addresses. |
| I32 wwpLeosNtpMulticastIndex | 1.3.6.1.4.1.6141.2.60.18.1.1.18.1.1 | Integer32 | not-accessible | Specifies the unique index of the entry. |
| IPt wwpLeosNtpMulticastInetAddrType | 1.3.6.1.4.1.6141.2.60.18.1.1.18.1.2 | InetAddressType | read-write | Specifies the type of address wwpLeosNtpMulticastInetAddr belongs to.
When set to:
ipv4 : wwpLeosNtpMulticastInetAddr should be compliant with
InetAddressIPv4 from RFC 4001
ipv6 : wwpLeosNtpMulticastInetAddr should be compliant with
InetAddressIPv6 from RFC 4001. |
| IP wwpLeosNtpMulticastInetAddr | 1.3.6.1.4.1.6141.2.60.18.1.1.18.1.3 | InetAddress | read-write | Specifies the NTP multicast address.
The InetAddress specified here will be compliant with RFC 4001. |
| ROW wwpLeosNtpMulticastRowStatus | 1.3.6.1.4.1.6141.2.60.18.1.1.18.1.4 | RowStatus | read-create | To create a row in this table, a manager must
set this object to 'createAndGo'.
To create entry in the table use SNMP multiple set operation
and following objects must be set: wwpLeosNtpMulticastInetAddrType,
wwpLeosNtpMulticastInetAddr and wwpLeosNtpMulticastRowStatus. |
| INT wwpLeosNtpClientSyncChangeNotifAdminState | 1.3.6.1.4.1.6141.2.60.18.1.1.19 | INTEGER | read-write | Set to on to turn on sync change notifications. |
| wwpLeosNtpClientNotifAttrs | 1.3.6.1.4.1.6141.2.60.18.1.2 | | | |
| INT wwpLeosNtpClientSyncState | 1.3.6.1.4.1.6141.2.60.18.1.2.1 | INTEGER | read-only | This object indicates the synchronized state of the NTP client. |
| wwpLeosNtpClientMIBNotificationPrefix | 1.3.6.1.4.1.6141.2.60.18.2 | | | |
| wwpLeosNtpClientMIBNotifications | 1.3.6.1.4.1.6141.2.60.18.2.0 | | | |
| NTF wwpLeosNtpClientSyncStatusChangeNotification | 1.3.6.1.4.1.6141.2.60.18.2.0.1 | | | This notification is sent whenever there is a change in the synchronization state for the
NTP client. wwpLeosNtpClientSyncChangeNotifAdminState should be enabled to receive this trap. |
| wwpLeosNtpClientMIBConformance | 1.3.6.1.4.1.6141.2.60.18.3 | | | |
| wwpLeosNtpClientMIBCompliances | 1.3.6.1.4.1.6141.2.60.18.3.1 | | | |
| wwpLeosNtpClientMIBGroups | 1.3.6.1.4.1.6141.2.60.18.3.2 | | | |
