All MIBs › Unisphere-Data-MPLS-MIB
Organization: Juniper Networks, Inc.
Last Updated: 2002-11-04
Category: Juniper Unisphere ERX Routing
Description: Manages Juniper/Unisphere ERX MPLS label switching, LSP configuration, and forwarding table entries.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Unisphere-Data-MPLS-MIB?
Unisphere-Data-MPLS-MIB is an enterprise MIB from Unisphere Networks (ERX router line, later Juniper) for configuring and monitoring MPLS label switching. It covers global LSR-wide settings, MPLS-enabled interfaces, tunnel and tunnel-profile definitions, and explicit path objects used to build label-switched paths. Administrators use it to check the software/control-plane health of the MPLS process, such as label range utilization, LDP and RSVP-TE session retry counters, and reoptimization timers, which reveal instability such as repeated LSP setup failures or exhausted label space. It complements (and its concepts parallel) the standard IETF MPLS-LSR-MIB and MPLS-TE-MIB, though it is a proprietary enterprise implementation rather than a direct extension of them. It is deployed on service-provider MPLS core and edge routers running Unisphere/Juniper ERX software. Engineers can download the Unisphere-Data-MPLS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Unisphere-Data-MPLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Unisphere/Juniper ERX MPLS-enabled router
Monitoring Examples
Polling usdMplsGroupLabelRangeLow/usdMplsGroupLabelRangeHigh shows how much of the label space is provisioned, while a rising usdMplsGroupLspRetryTimes or usdMplsGroupLdpRetryTimesNoroute count indicates LSPs repeatedly failing to signal, often due to a missing route or misconfigured neighbor. usdMplsGroupReopTimer can be checked to confirm the reoptimization interval matches policy. usdMplsLsrGlobalConfig under usdMplsObjects gives the overall enable/disable state of MPLS on the router.
What Can Be Monitored
- MPLS label range utilization
- LSP setup retry counts
- LDP retry/no-route counts
- reoptimization timer
- global MPLS enable state
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From Unisphere-Data-MIBs
| usDataMibs | MODULE-IDENTITY |
From Unisphere-Data-TC
| UsdNextIfIndex |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| usdMplsMIB | 1.3.6.1.4.1.4874.2.2.54 | The MultiProtocol Label Switching (MPLS) MIB for the Unisphere Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations. | ||
| usdMplsObjects | 1.3.6.1.4.1.4874.2.2.54.1 | |||
| usdMplsLsrGlobalConfig | 1.3.6.1.4.1.4874.2.2.54.1.1 | |||
| usdMplsGroup | 1.3.6.1.4.1.4874.2.2.54.1.1.1 | |||
| INT usdMplsGroupMplsEnable | 1.3.6.1.4.1.4874.2.2.54.1.1.1.1 | INTEGER | read-write | Enables or disables MPLS on the virtual router. When MPLS is created on the virtual router (VR), it remains adminstratively disabled untill it is enabled explicitly. Without administratively enabling the MPLS on VR, it won't function as an LSR even though it holds the MPLS configurations until the MPLS context is destroyed for the VR. |
| I32 usdMplsGroupReopTimer | 1.3.6.1.4.1.4874.2.2.54.1.1.1.2 | Integer32 | read-write | All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. This object allows configuration of the frequency of reoptimization in time interval. |
| I32 usdMplsGroupLabelRangeLow | 1.3.6.1.4.1.4874.2.2.54.1.1.1.3 | Integer32 | read-write | The lower end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently. |
| I32 usdMplsGroupLabelRangeHigh | 1.3.6.1.4.1.4874.2.2.54.1.1.1.4 | Integer32 | read-write | The higher end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently. |
| I32 usdMplsGroupLspRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.5 | Integer32 | read-write | This object configures the number of retries for LSP setup after a failure due to no available route. |
| I32 usdMplsGroupLspRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.6 | Integer32 | read-write | This object configures the time interval between two successive LSP setup retries after a failure due to no available route. |
| I32 usdMplsGroupLspRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.1.1.7 | Integer32 | read-write | Use this object to configure number of retries for LSP setup after a failure other than one due to no available route. |
| I32 usdMplsGroupLspRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.1.1.8 | Integer32 | read-write | Use this object to configure the time interval between two LSP setup retries after a failure other than one due to no available route. |
| I32 usdMplsGroupLdpRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.9 | Integer32 | read-write | Use this object to configure the number of retries for LDP to setup LSP after a failure due to no available route. |
| I32 usdMplsGroupLdpRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.10 | Integer32 | read-write | Use this object to configure the time interval between two successive LSP setup retries by LDP after a failure due to no available route. |
| I32 usdMplsGroupLdpRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.1.1.11 | Integer32 | read-write | Use this object to configure LSP setup retries by LDP after a failure other than one due to no available route. |
| I32 usdMplsGroupLdpRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.1.1.12 | Integer32 | read-write | Use this object to configure time interval between two LSP setup retries by LDP after a failure other than one due to no available route. |
| I32 usdMplsGroupLdpSessionRetries | 1.3.6.1.4.1.4874.2.2.54.1.1.1.13 | Integer32 | read-write | Use this object to configure the number of LDP session retries. |
| I32 usdMplsGroupLdpSessionRetryTimer | 1.3.6.1.4.1.4874.2.2.54.1.1.1.14 | Integer32 | read-write | Use this object to configure the time interval between two LDP session retries. |
| STR usdMplsGroupTopologyDrivenIpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.1.1.15 | DisplayString | read-write | Usually IP interfaces are stacked on top of the MPLS tunnels. The profiled tunnels are associated with IP interfaces with profile of IP interfaces. This object configures the name for the IP profile. |
| T/F usdMplsGroupTopologyDrivenLdpEgressIpIntf | 1.3.6.1.4.1.4874.2.2.54.1.1.1.16 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over egress LSPs setup by topology driven LSP setup configurations. |
| T/F usdMplsGroupTopologyDrivenLdpIngressIpIntf | 1.3.6.1.4.1.4874.2.2.54.1.1.1.17 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over ingress LSPs setup by topology driven LSP setup configurations. |
| T/F usdMplsGroupTopologyDrivenLdpEgressIpIntfHostOnly | 1.3.6.1.4.1.4874.2.2.54.1.1.1.18 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over egress LSPs to host only IP addresses setup by topology driven LSP setup configurations. |
| T/F usdMplsGroupTopologyDrivenLdpIngressIpIntfHostOnly | 1.3.6.1.4.1.4874.2.2.54.1.1.1.19 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over ingress LSPs to host only IP addresses setup by topology driven LSP setup configurations. |
| INT usdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListType | 1.3.6.1.4.1.4874.2.2.54.1.1.1.20 | INTEGER | read-write | There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the egress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently. |
| INT usdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListType | 1.3.6.1.4.1.4874.2.2.54.1.1.1.21 | INTEGER | read-write | There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the ingress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently. |
| STR usdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyList | 1.3.6.1.4.1.4874.2.2.54.1.1.1.22 | DisplayString | read-write | This object used to configure egress list name of topology driven LSPs over IP interfaces. For successful configurations the egress list name must be set cunncurently with egress list type. Set the list type and list name cuncurrently. |
| STR usdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyList | 1.3.6.1.4.1.4874.2.2.54.1.1.1.23 | DisplayString | read-write | This object used to configure ingress list name of topology driven LSPs over IP interfaces. For successful configurations ingress listname set cunncurently with ingress list type. Set the list type and list name cuncurrently. |
| INT usdMplsGroupTopologyDrivenLdp | 1.3.6.1.4.1.4874.2.2.54.1.1.1.24 | INTEGER | read-write | LDP is used for label distributions control for setting up the LSPs. Topology driven LSPs also setup using LDP label distribution control. This object allows to enable/disable LDP admin state used for topology driven LSPs setup. |
| INT usdMplsGroupLspLabelDistCtrlMode | 1.3.6.1.4.1.4874.2.2.54.1.1.1.25 | INTEGER | read-only | Some FECs correspond to address prefixes which are distributed via a dynamic routing algorithm. The setup of the LSPs for these FECs can be done in one of two ways: Independent LSP Control or Ordered LSP Control. This object displays the LSP lable distribution control mode. |
| T/F usdMplsGroupLdpAdvHostOnly | 1.3.6.1.4.1.4874.2.2.54.1.1.1.26 | TruthValue | read-write | This object allows to enable/disable LDP label advertisement mode for host only LSPs. |
| STR usdMplsGroupLsrState | 1.3.6.1.4.1.4874.2.2.54.1.1.1.27 | DisplayString | read-only | This object value displays the status of MPLS enabled LSR such as state is up or down etc. |
| T/F usdMplsGroupReopNow | 1.3.6.1.4.1.4874.2.2.54.1.1.1.28 | TruthValue | read-write | All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. Setting this object forces an immediate check for better paths for the existing LSPs. |
| usdMplsGroupList | 1.3.6.1.4.1.4874.2.2.54.1.1.2 | |||
| usdMplsGroupTargetedHelloSendTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1 | not-accessible | This table contains list of send side IP addresses for LDP targeted hello messages. | |
| usdMplsGroupTargetedHelloSendEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1 | not-accessible | Each entry represents send IP address for targeted hello message. | |
| IP usdMplsGroupTargetedHelloSendAddress | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.1 | IpAddress | not-accessible | Configure the send side address for targeted hello messages. |
| INT usdMplsGroupLdpTargetedHelloSendMode | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.2 | INTEGER | read-create | Select mode to add/delete to the list of IP addresses for targeted hello messages. |
| usdMplsGroupTargetedHelloReceiveTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2 | not-accessible | This table contains list of receive side IP addresses for LDP targeted hello messages. | |
| usdMplsGroupTargetedHelloReceiveEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1 | not-accessible | Each entry represents receive IP address for targeted hello message. | |
| IP usdMplsGroupTargetedHelloReceiveAddress | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.1 | IpAddress | not-accessible | Configure the receive side address for targeted hello messages. |
| INT usdMplsGroupLdpTargetedHelloReceiveMode | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.2 | INTEGER | read-create | Select mode to add/delete to the list of IP addresses for targeted hello messages. |
| usdMplsGroupLdpLabelAdverRouteListTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3 | not-accessible | Table is a list of LDP label advertisement entries. | |
| usdMplsGroupLdpLabelAdverRouteListEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1 | not-accessible | Each entry represents access list pairs for the LDP peers label advertisement. | |
| STR usdMplsGroupLdpLabelAdverRouteListName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.1 | DisplayString | not-accessible | This LDP label advertisement route list name for which this entry contains information. |
| STR usdMplsGroupLdpLabelAdverNbrListName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.2 | DisplayString | not-accessible | The LDP label advertisement neighbor route list name for which this entry contains information. |
| INT usdMplsGroupLabelAdverListMode | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.3 | INTEGER | read-create | This object selects the mode of addition/deletion to the list. |
| usdMplsGroupLdpProfileTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4 | not-accessible | Table is a list of LDP Profile entries. | |
| usdMplsGroupLdpProfileEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1 | not-accessible | Each entry represents one LDP profile settings. | |
| STR usdMplsGroupLdpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.1 | DisplayString | not-accessible | LDP profile name identifies unique entry in the table. |
| I32 usdMplsGroupLdpProfileHelloHoldTime | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.2 | Integer32 | read-create | Configure the LDP peers hello hold time period. |
| INT usdMplsGroupLdpProfileCrLdpAdminState | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.3 | INTEGER | read-create | Enable or disable the constraint-based routing label distribution protocol (CR-LDP) admin state. |
| ROW usdMplsGroupLdpProfileRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.4 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsGroupLdpProfileCrLdpAdminState usdMplsGroupLdpProfileRowStatus |
| usdMplsGroupRsvpProfileTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5 | not-accessible | Table is a list of LDP Profile entries. | |
| usdMplsGroupRsvpProfileEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1 | not-accessible | Each entry represents one LDP profile settings. | |
| STR usdMplsGroupRsvpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.1 | DisplayString | not-accessible | The RSVP profile name identifies unique entry in the table. |
| U32 usdMplsGroupRsvpProfileRefreshPeriod | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.2 | Unsigned32 | read-create | Configure the time out period between the generation of two refresh messages. |
| I32 usdMplsGroupRsvpProfileCleanupTimeoutFactor | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.3 | Integer32 | read-create | Confgure the number of refresh messages can be lost before PATH or RESV state is ended. |
| ROW usdMplsGroupRsvpProfileRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.4 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: usdMplsGroupRsvpProfileRowStatus |
| usdMplsMajorLayer | 1.3.6.1.4.1.4874.2.2.54.1.2 | |||
| usdMplsIfMajorLayer | 1.3.6.1.4.1.4874.2.2.54.1.2.1 | |||
| USD usdMplsIfMajorNextIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.2.1.1 | UsdNextIfIndex | read-only | Coordinate ifIndex value allocation for entries in the usdMplsIfMajorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. |
| usdMplsIfMajorTable | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2 | not-accessible | This table contains entries for MPLS Major interfaces present in the system. | |
| usdMplsIfMajorEntry | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1 | not-accessible | Each entry describes the characteristics of an MPLS Major interface. Creating/deleting entries in this table causes corresponding entries to be created/deleted in ifTable/ifXTable/usdIfTable. | |
| NUM usdMplsIfMajorIndex | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.1 | InterfaceIndex | not-accessible | The ifIndex of the MPLS Major interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsIfMajorNextIfIndex. |
| ROW usdMplsIfMajorRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.2 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMajorRowStatus usdMplsIfMajorLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for usdMplsIfMajorIndex must have been determined previously, by reading usdMplsIfMajorNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created/ destroyed as a result of creating/destroying an entry in this table. |
| NUM usdMplsIfMajorLowerIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.3 | InterfaceIndexOrZero | read-create | The ifIndex of an interface over which this MPLS Major interface to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation. |
| INT usdMplsIfMajorAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.4 | INTEGER | read-create | Use this object to create MPLS major interface stacked over any link layer interface. Lower layer(index) over which major stacks has to be specified for successful creation of the major interface. |
| INT usdMplsIfMajorLdpAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.5 | INTEGER | read-create | This object enables/disables LDP admin status on the MPLS interface. |
| STR usdMplsIfMajorLdpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.6 | DisplayString | read-create | All the LDP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the LDP profile name. |
| USD usdMplsIfMajorLdpVpiStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.7 | UsdMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the stop range cunncurrently. |
| USD usdMplsIfMajorLdpVpiStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.8 | UsdMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the start range cunncurrently. |
| USD usdMplsIfMajorLdpVciStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.9 | UsdMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the stop range cunncurrently. |
| USD usdMplsIfMajorLdpVciStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.10 | UsdMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the start range cunncurrently. |
| INT usdMplsIfMajorRsvpAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.11 | INTEGER | read-create | This object configures RSVP admin status for MPLS interface. |
| STR usdMplsIfMajorRsvpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.12 | DisplayString | read-create | All the RSVP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the RSVP profile name. |
| USD usdMplsIfMajorRsvpVpiStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.13 | UsdMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the stop range cunncurrently. |
| USD usdMplsIfMajorRsvpVpiStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.14 | UsdMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the start range cunncurrently. |
| USD usdMplsIfMajorRsvpVciStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.15 | UsdMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the stop range cunncurrently. |
| USD usdMplsIfMajorRsvpVciStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.16 | UsdMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the start range cunncurrently. |
| INT usdMplsIfMajorLabelSpaceType | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.17 | INTEGER | read-only | Displays the label space type for the MPLS interface. |
| INT usdMplsIfMajorOpState | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.18 | INTEGER | read-only | This object displays MPLS major interface operation state. |
| INT usdMplsIfMajorCrLdpAdminState | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.19 | INTEGER | read-only | This object displays the admin state of CR-LDP. |
| usdMplsMinorLayer | 1.3.6.1.4.1.4874.2.2.54.1.3 | |||
| usdMplsIfMinorLayer | 1.3.6.1.4.1.4874.2.2.54.1.3.1 | |||
| USD usdMplsIfMinorNextIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.1 | UsdNextIfIndex | read-only | Coordinates ifIndex value allocation for entries in the usdMplsIfMinorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. |
| usdMplsIfMinorTable | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2 | not-accessible | This table contains entries for MPLS Minor interfaces present in the system. | |
| usdMplsIfMinorEntry | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1 | not-accessible | Each entry describes the characteristics of an MPLS Minor interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/usdIfTable. | |
| NUM usdMplsIfMinorIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.1 | InterfaceIndex | not-accessible | The ifIndex of the MPLS Minor interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsMinorNextIfIndex. |
| ROW usdMplsIfMinorRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.2 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMinorRowStatus usdMplsIfMinorTunnelName In addition, when creating an entry the following conditions must hold: A value for usdMplsIfMinorIndex must have been determined previously, by reading usdMplsMinorNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created/ destroyed as a result of creating/destroying an entry in this table. |
| NUM usdMplsIfMinorLowerIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.3 | InterfaceIndexOrZero | read-only | The ifIndex of an interface over which this MPLS Minor interface is to be layered. A value of zero indicates no layering. As minor interface can be created without stacking on major interface, as and when it stacks on major interface by signalling protocol, it's value can be read. |
| INT usdMplsIfMinorAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.4 | INTEGER | read-create | With this object minor interface admin status can be enabled/disabled. |
| IP usdMplsIfMinorEndpointAddress | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.5 | IpAddress | read-create | This object configures the IP address of the tunnel destination. This object can be set along with the usdMplsIfMinorEndpointDstMask to configure the tunnel destination mask, but it is optional. |
| IP usdMplsIfMinorEndpointDstMask | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.6 | IpAddress | read-create | This object configures the tunnel destination mask. It can be set along with the usdMplsIfMinorEndpointAddress. |
| INT usdMplsIfMinorTunnelMetricMode | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.7 | INTEGER | read-create | Select the relative or absolute mode to configure the absolute or relative tunnel metric. To set the tunnel to relative metric, usdMplsIfMinorRelativeTunnelMetric has to be set along with this object option as relative. To set the tunnel to absolute metric, usdMplsIfMinorAbsoluteTunnelMetric has to be set along with this object option as absolute. |
| U32 usdMplsIfMinorAbsoluteTunnelMetric | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.8 | Unsigned32 | read-create | This object allows configuration of absolute metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it. |
| I32 usdMplsIfMinorRelativeTunnelMetric | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.9 | Integer32 | read-create | This object allows configuration of relative metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it. |
| INT usdMplsIfMinorLabelDistProto | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.10 | INTEGER | read-create | This object allows to select label distribution protocol. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels. |
| T/F usdMplsIfMinorAnnounceToOspf | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.11 | TruthValue | read-create | This object allows to register LSP endpoints to OSPF to next hop calculation. |
| T/F usdMplsIfMinorAnnounceToIsis | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.12 | TruthValue | read-create | This object allows to register LSP endpoints to IS-IS for next hop calculation. |
| T/F usdMplsIfMinorAnnounceToBgp | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.13 | TruthValue | read-create | This object allows to register LSP endpoints to BGP for next hop calculation. |
| USD usdMplsIfMinorBandwidth | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.14 | UsdMinorCfgBWRanges | read-create | This object allows configuration of bandwidth requirements for the tunnel. |
| OCT usdMplsIfMinorAffinity | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.15 | OCTET STRING | read-create | This object allows configuration of resource class affinity for the tunnel. |
| OCT usdMplsIfMinorAffinityMask | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.16 | OCTET STRING | read-create | This allows to set the resource class affinity mask. Since it is a mask, set along with the affinity for successful configurations. |
| USD usdMplsIfMinorSetupPriority | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.17 | UsdMinorCfgHoldingAndSetupPriorityRanges | read-create | This object allows configuration of preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| USD usdMplsIfMinorHoldingPriority | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.18 | UsdMinorCfgHoldingAndSetupPriorityRanges | read-create | This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| STR usdMplsIfMinorTunnelName | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.19 | DisplayString | read-create | This object allows configuration of the tunnel name to be associated with tunnel settings. |
| USD usdMplsIfMinorTunnelRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.20 | UsdMinorCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the number of retries for tunnel setup. |
| NUM usdMplsIfMinorTunnelRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.21 | UsdMinorCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of retry interval for tunnel setup. |
| USD usdMplsIfMinorTunnelRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.22 | UsdMinorCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the tunnel retries when no route notifications are received. |
| NUM usdMplsIfMinorTunnelRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.23 | UsdMinorCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of the tunnel retry interval when no route notifications are received. |
| STR usdMplsIfMinorBaseTunnelName | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.24 | DisplayString | read-create | This object allows configuration of the base tunnel name over which all the tunnels are stacked over. |
| I32 usdMplsIfMinorVpnOuiNumber | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.25 | Integer32 | read-create | This object allows configuration of the OUI part of VPN ID. |
| IP usdMplsIfMinorVpnIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.26 | IpAddress | read-create | This object allows configuration of the index part of VPN ID. |
| INT usdMplsIfMinorTunnelOpState | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.27 | INTEGER | read-only | This object displays the tunnel operation state. established : Tunnel established teNegotiation : TE Negotiation up : Tunnel Up down : Tunnel Down cfgChanged : Tunnel config changed cfgIncEn : Tunnel incomplete Config Admin State Enable cfgIncDis : Tunnel incomplete Config Admin State Disable disabled : Tunnel disabled rel : noChange : Tunnel state no change |
| T/F usdMplsIfMinorTargetedDynamicTunnel | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.28 | TruthValue | read-create | Configure targeted dynamic tunnel. |
| T/F usdMplsIfMinorReoptimization | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.29 | TruthValue | read-create | Configure tunnel reoptimization. |
| usdMplsMinorLayerList | 1.3.6.1.4.1.4874.2.2.54.1.3.2 | |||
| usdMplsIfMinorPathOptionTable | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1 | not-accessible | Table is a list of different LSP paths as option for each LSP setup. | |
| usdMplsIfMinorPathOptionEntry | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1 | not-accessible | Each entry represents one path option for the LSP. | |
| NUM usdMplsIfMinorPathOptionIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.1 | InterfaceIndex | not-accessible | Minor interface uid. |
| I32 usdMplsIfMinorPathOptionNumber | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.2 | Integer32 | not-accessible | Unique number to identify each path option configured. |
| INT usdMplsIfMinorPathOptionProtocol | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.3 | INTEGER | read-create | Select the each path option explicit routing protocol. |
| T/F usdMplsIfMinorPathOptionLockdown | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.4 | TruthValue | read-create | Enable/disable each configured path option reoptimization. |
| STR usdMplsIfMinorPathOptionPathName | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.5 | DisplayString | read-create | Configure the name for each path option. |
| I32 usdMplsIfMinorPathOptionPathId | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.6 | Integer32 | read-create | Configure the path option ID. Either the name or ID will be associated with a path at a time. If the path name and ID are set at a same time for the path, the name will have precedence over ID. |
| ROW usdMplsIfMinorPathOptionRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.7 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMinorPathOptionRowStatus. |
| usdMplsTunnelProfile | 1.3.6.1.4.1.4874.2.2.54.1.4 | |||
| usdMplsTunnelProfileGroup | 1.3.6.1.4.1.4874.2.2.54.1.4.1 | |||
| usdMplsTunnelProfileTable | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1 | not-accessible | Table is a list of tunnel profiles for a given VR. | |
| usdMplsTunnelProfileEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1 | not-accessible | Each entry represents one tunnel profile. | |
| STR usdMplsTunnelProfileName | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.1 | DisplayString | not-accessible | Associate a name for the configured tunnel profile settings. |
| INT usdMplsTunnelProfileAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.2 | INTEGER | read-create | Enable/disable the adminstatus of the tunnel profile. |
| STR usdMplsTunnelProfileBaseTunnelName | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.3 | DisplayString | read-create | Configure the base tunnel name in tunnel profile settings. This base tunnel is the one over which all the other tunnels are stacked over. Configured base tunnel name in profile settings will be associated with the actual configured base tunnel name. |
| STR usdMplsTunnelProfileIpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.4 | DisplayString | read-create | Configures the name for IP profile settings for the IP interfaces over which MPLS tunnels are stacked. |
| INT usdMplsTunnelProfileLabelDistProto | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.5 | INTEGER | read-create | Configure the label distribution protocol to associate with a tunnel profile. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels. |
| T/F usdMplsTunnelProfileAnnounceToOspf | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.6 | TruthValue | read-create | Configure the routing protocol for next hop calculations as OSPF. |
| T/F usdMplsTunnelProfileAnnounceToIsis | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.7 | TruthValue | read-create | Configure routing protocol for next hop calculations as ISIS. |
| T/F usdMplsTunnelProfileAnnounceToBgp | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.8 | TruthValue | read-create | Configure routing protocol for next hop calculations as BGP. |
| INT usdMplsTunnelProfileMetricMode | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.9 | INTEGER | read-create | Select the relative or absolute mode to configure the absolute or relative tunnel profile metric. To set the tunnel profile to relative metric, usdMplsTunnelProfileRelativeMetric has to be set along with this object option as relative. To set the tunnel profile to absolute metric, usdMplsTunnelProfileAbsoluteMetric has to be set along with this object option as absolute. |
| U32 usdMplsTunnelProfileAbsoluteMetric | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.10 | Unsigned32 | read-create | This object allows configuration of the absolute metric values. Refer to usdMplsTunnelProfileMetricMode for how set it. |
| I32 usdMplsTunnelProfileRelativeMetric | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.11 | Integer32 | read-create | This object allows configuration of the relative metric values. Refer to usdMplsTunnelProfileMetricMode for how set it. |
| USD usdMplsTunnelProfileBandwidth | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.12 | UsdProfileCfgBWRanges | read-create | This object allows configuration of bandwidth requirements for the tunnel. |
| OCT usdMplsTunnelProfileAffinity | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.13 | OCTET STRING | read-create | This object allows configuration of the resource class affinity for the tunnel. This can set independently of usdMplsTunnelProfileAffinityMask. |
| OCT usdMplsTunnelProfileAffinityMask | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.14 | OCTET STRING | read-create | This allows configuration of which bits in the affinity must match the resource class bits. Can't be set independently; always with usdMplsTunnelProfileAffinity. Specify the value in bit mask format. |
| USD usdMplsTunnelProfileSetupPriority | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.15 | UsdProfileCfgHoldingAndSetupPriorityRanges | read-create | This object configuration of the preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| USD usdMplsTunnelProfileHoldingPriority | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.16 | UsdProfileCfgHoldingAndSetupPriorityRanges | read-create | This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| USD usdMplsTunnelProfileRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.17 | UsdProfileCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the number of retries for the tunnel setup. |
| NUM usdMplsTunnelProfileRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.18 | UsdProfileCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of retry interval for tunnel setup. |
| USD usdMplsTunnelProfileRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.19 | UsdProfileCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the tunnel retries when no route notifications are received. |
| NUM usdMplsTunnelProfileRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.20 | UsdProfileCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of the tunnel retry interval when no route notifications are received. |
| I32 usdMplsTunnelProfileVpnOuiNumber | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.21 | Integer32 | read-create | This object allows configuration of the OUI part of VPN ID. |
| IP usdMplsTunnelProfileVpnIndex | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.22 | IpAddress | read-create | This object allows configuration of the index part of VPN ID. |
| ROW usdMplsTunnelProfileRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.23 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfileRowStatus |
| T/F usdMplsTunnelProfileTargetedDynamicTunnel | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.24 | TruthValue | read-create | Configure targeted dynamic tunnel. |
| usdMplsTunnelProfileList | 1.3.6.1.4.1.4874.2.2.54.1.4.2 | |||
| usdMplsTunnelProfilePathOptionTable | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1 | not-accessible | Table is a list of different LSP paths as option for each LSP setup, configured as part of tunnel profile settings | |
| usdMplsTunnelProfilePathOptionEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1 | not-accessible | Each entry represents one path option for the LSP setup, configured as a part of tunnel profile settings. | |
| STR usdMplsTunnelProfileNamePathOption | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.1 | DisplayString | not-accessible | Name of the path option. |
| I32 usdMplsTunnelProfilePathOptionNumber | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.2 | Integer32 | not-accessible | Unique identifier for the path option. |
| INT usdMplsTunnelProfilePathOptionProtocol | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.3 | INTEGER | read-create | Path selection option protocol. |
| T/F usdMplsTunnelProfilePathOptionLockdown | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.4 | TruthValue | read-create | Enable/disable path selection option reoptimization. |
| STR usdMplsTunnelProfilePathOptionPathName | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.5 | DisplayString | read-create | Associate a name with each explicit path. |
| I32 usdMplsTunnelProfilePathOptionPathId | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.6 | Integer32 | read-create | Each explicit path can be associated either name or ID. This object allows configuration of the ID for the explicit path. |
| ROW usdMplsTunnelProfilePathOptionRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.7 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfilePathOptionRowStatus. |
| usdMplsTunnelProfileDynamicEndpointTable | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2 | not-accessible | This table contains entries for the dynamic endpoints configured for each tunnel profile. | |
| usdMplsTunnelProfileDynamicEndpointEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1 | not-accessible | Dynamic endpoint entries for each tunnel profile. | |
| STR usdMplsTunnelProfileNameDynamicEndpoint | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.1 | DisplayString | not-accessible | Configure the tunnel dynamic endpoint in tunnel profile settings. |
| INT usdMplsTunnelProfileDynamicEndpointType | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.2 | INTEGER | not-accessible | Configure the dynamic endpoint type for the tunnel. |
| INT usdMplsTunnelProfileDynamicEndpointPolicyListType | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.3 | INTEGER | not-accessible | This object allows configuration of the dynamic tunnel policy type selection. |
| STR usdMplsTunnelProfileDynamicEndpointListName | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.4 | DisplayString | not-accessible | This object allows configuration of the dynamic endpoints access list name. |
| ROW usdMplsTunnelProfileDynamicEndpointRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.5 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: usdMplsTunnelProfileDynamicEndpointRowStatus. |
| usdMplsTunnelProfileTunnelEndpointTable | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3 | not-accessible | Table contains list of tunnel static enpoints configured for each tunnel profile. | |
| usdMplsTunnelProfileTunnelEndpointEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1 | not-accessible | Each entry represents one static endpoint configuration for the tunnel. | |
| STR usdMplsTunnelProfileNameTunnelEndpoint | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.1 | DisplayString | not-accessible | This object configures the tunnel profile name. |
| IP usdMplsTunnelProfileTunnelEndpointAddress | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.2 | IpAddress | not-accessible | This object configures the IP address of the tunnel destination. |
| IP usdMplsTunnelProfileTunnelEndpointDstMask | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.3 | IpAddress | not-accessible | This object configures the tunnel destination mask. |
| ROW usdMplsTunnelProfileTunnelEndpointRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.4 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfileTunnelEndpointRowStatus. |
| usdMplsExplicitPath | 1.3.6.1.4.1.4874.2.2.54.1.5 | |||
| usdMplsExplicitPathGroup | 1.3.6.1.4.1.4874.2.2.54.1.5.1 | |||
| usdMplsExplicitPathTable | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1 | not-accessible | Table is a list of hops configurations for explicit paths. | |
| usdMplsExplicitPathEntry | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1 | not-accessible | Each entry represents one hop configuration for the particular explicit path. | |
| STR usdMplsExplicitPathName | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.1 | DisplayString | not-accessible | Configure the name for the explicit path used as table index. |
| INT usdMplsExplicitPathAdminState | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.2 | INTEGER | read-create | Enable/disable explicit path adminstatus. |
| ROW usdMplsExplicitPathRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.3 | RowStatus | read-create | Creation/deletion of the explicit path is done through setting this object. |
| usdMplsExplicitPathNodeTable | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2 | not-accessible | Table is a list of configured explicit paths. | |
| usdMplsExplicitPathNodeEntry | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1 | not-accessible | Each entry represents one hop in a particular explicit path. | |
| STR usdMplsExplicitPathNodeName | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.1 | DisplayString | not-accessible | Configure the name for the explicit path used in the table index. |
| I32 usdMplsExplicitPathNodeIndexNumber | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.2 | Integer32 | not-accessible | Each explicit path hop will have an index associated with it. Configure each path hop index using this object. |
| T/F usdMplsExplicitPathNodeLoose | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.3 | TruthValue | read-create | Configure the explicit path hop as strict or loose. Set along with HopAddress. |
| IP usdMplsExplicitPathNodeHopAddress | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.4 | IpAddress | read-create | Configure the hop IP address to setup explicit path. Explicit path next hop will be created when the mentioned hop IP address doesn't belong to any of the existing hop even without setting the rowStatus createAndGo value. The rowStatus value is used to destroy the node. |
| IP usdMplsExplicitPathNodeHopAddressMask | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.5 | IpAddress | read-create | Configure the hop IP address mask. Set along with hop address. |
| ROW usdMplsExplicitPathNodeRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.6 | RowStatus | read-create | Use this object for deletion of the node. For node creation, this value have no effect. Setting the node with IP address create the node. To delete the node set only this object. |
| usdMplsConformance | 1.3.6.1.4.1.4874.2.2.54.2 | |||
| usdMplsCompliances | 1.3.6.1.4.1.4874.2.2.54.2.1 | |||
| usdMplsCompliance | 1.3.6.1.4.1.4874.2.2.54.2.1.1 | Obsolete compliance statement for entities which implement the Unisphere MPLS MIB. This statement became obsolete when RowStatus support was added to some of the minor layer and tunnel profile tables. | ||
| usdMplsCompliance2 | 1.3.6.1.4.1.4874.2.2.54.2.1.2 | The compliance statement for entities which implement the Unisphere MPLS MIB. | ||
| usdMplsConfGroups | 1.3.6.1.4.1.4874.2.2.54.2.2 | |||
| usdMplsLsrGlobalConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.1 | A collection of objects providing management of MPLS label switching routers (LSRs) in a Unisphere product. | ||
| usdMplsMajorLayerConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.2 | A collection of objects providing management of major MPLS interfaces in a Unisphere product. | ||
| usdMplsMinorLayerConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.3 | Obsolete collection of objects providing management of minor MPLS (tunnel) in a Unisphere product. This group became obsolete when the usdMplsIfMinorPathOptionRowStatus object was added. | ||
| usdMplsTunnelProfileConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.4 | Obsolete collection of objects providing management of MPLS tunnel profiles in a Unisphere product. This group became obsolete when the objects usdMplsTunnelProfilePathOptionRowStatus, usdMplsTunnelProfileDynamicEndpointRowStatus and usdMplsTunnelProfileTunnelEndpointRowStatus were added. | ||
| usdMplsExplicitPathConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.5 | A collection of objects providing management of MPLS explicit paths in a Unisphere product. | ||
| usdMplsMinorLayerConfGroup2 | 1.3.6.1.4.1.4874.2.2.54.2.2.6 | A collection of objects providing management of minor MPLS (tunnel) interfaces in a Unisphere product. | ||
| usdMplsTunnelProfileConfGroup2 | 1.3.6.1.4.1.4874.2.2.54.2.2.7 | A collection of objects providing management of MPLS tunnel profiles in a Unisphere product. |
RFC description
Comprehensive MPLS configuration management including tunnels, explicit paths, CR-LDP, and BGP/MPLS VPN settings.
Start monitoring Unisphere/Juniper ERX MPLS-enabled router (LSR/tunnel/LDP-RSVP session status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.