Unisphere-Data-PIM-MIB

All MIBs › Unisphere-Data-PIM-MIB

Organization: Unisphere Networks, Inc.

Last Updated: 2001-03-19

Category: Juniper Unisphere ERX Routing

Description: Manages Unisphere ERX Protocol Independent Multicast configuration, RP mapping, and neighbor state.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Unisphere-Data-PIM-MIB?

Unisphere-Data-PIM-MIB is an enterprise MIB for Unisphere (ERX/Juniper) routers that manages and monitors Protocol Independent Multicast (PIM) routing. It exposes per-interface counters for PIM control messages, Hello, Join/Prune, Assert, and Graft/Graft-Ack, sent and received, plus a PIM interface table and traps. These counters let an administrator monitor the software health of the multicast routing process, spotting neighbor flapping (repeated Hellos), rendezvous-point instability (frequent Asserts), or PIM-Dense-Mode graft storms. The object model mirrors the intent of the standard PIM-MIB (RFC 5060) though implemented as a Unisphere-specific module with its own traps. It's typically deployed on service-provider or enterprise routers carrying IP multicast traffic such as IPTV or financial market data feeds, and administrators can download the Unisphere-Data-PIM-MIB file to load its object definitions into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Unisphere-Data-PIM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Unisphere/Juniper ERX multicast-enabled router

Monitoring Examples

An admin would poll usdPimInterfaceTable/usdPimInterfaceEntry for each multicast-enabled interface and watch usdPimNumHelloRcvd against usdPimNumHelloSent to confirm bidirectional neighbor adjacency. A spike in usdPimNumAssertRcvd suggests two routers are contending for forwarder status on a shared LAN segment. usdPimTraps would fire to alert on PIM neighbor loss without needing continuous polling.

What Can Be Monitored

PIM Hello messages sent/received
Join/Prune counts
Assert message counts
Graft/Graft-Ack counts
PIM interface state

Imported Objects

From IF-MIB

InterfaceIndex

From PIM-MIB

pimInterfaceIfIndex	OBJECT-TYPE
pimRPSetAddress	OBJECT-TYPE
pimRPSetComponent	OBJECT-TYPE
pimRPSetGroupAddress	OBJECT-TYPE
pimRPSetGroupMask	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

From Unisphere-Data-MIBs

usDataMibs

MODULE-IDENTITY

How to Use in IPNetwork Monitor

Example using usdPimNumHelloRcvd OID:

Select an Unisphere/Juniper ERX multicast-enabled router (PIM Hello/Join-Prune/Assert counter status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type usdPimNumHelloRcvd into the Find box to locate it in the OID tree, then select it and click OK. It reports the total number of Hellos received by PIM on this router. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the count changes from its expected baseline, since that would indicate the underlying set of items changed unexpectedly. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
usdPimMIB	1.3.6.1.4.1.4874.2.2.43			The enterprise MIB module for management of PIM routers.
usdPimMIBObjects	1.3.6.1.4.1.4874.2.2.43.1
usdPimTraps	1.3.6.1.4.1.4874.2.2.43.1.0
usdPimGlobal	1.3.6.1.4.1.4874.2.2.43.1.1
I32 usdPimNumHelloRcvdEx	1.3.6.1.4.1.4874.2.2.43.1.1.1	Integer32	read-only	Total number of Hellos received by PIM on this router.
I32 usdPimNumJoinPruneRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.2	Integer32	read-only	Total number of JoinPrunes received by PIM on this router.
I32 usdPimNumAssertRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.3	Integer32	read-only	Total number of Asserts received by PIM on this router.
I32 usdPimNumGraftRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.4	Integer32	read-only	Total number of Grafts received by PIM on this router.
I32 usdPimNumGraftAckRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.5	Integer32	read-only	Total number of Graft Acks received by PIM on this router.
I32 usdPimNumHelloSent	1.3.6.1.4.1.4874.2.2.43.1.1.6	Integer32	read-only	Total number of Hellos sent by PIM on this router.
I32 usdPimNumJoinPruneSent	1.3.6.1.4.1.4874.2.2.43.1.1.7	Integer32	read-only	Total number of JoinPrunes sent by PIM on this router.
I32 usdPimNumAssertSent	1.3.6.1.4.1.4874.2.2.43.1.1.8	Integer32	read-only	Total number of Asserts sent by PIM on this router.
I32 usdPimNumGraftSent	1.3.6.1.4.1.4874.2.2.43.1.1.9	Integer32	read-only	Total number of Grafts sent by PIM on this router.
I32 usdPimNumGraftAckSent	1.3.6.1.4.1.4874.2.2.43.1.1.10	Integer32	read-only	Total number of Graft Acks sent by PIM on this router.
usdPimInterfaceTable	1.3.6.1.4.1.4874.2.2.43.1.1.11		not-accessible	The (conceptual) table listing enterprise specific information on a subset of the rows of the pimInterfaceTable defined in the standard PIM MIB.
usdPimInterfaceEntry	1.3.6.1.4.1.4874.2.2.43.1.1.11.1		not-accessible	An entry (conceptual row) in the usdPimInterfaceTable. There is one entry per entry in the pimInterfaceTable.
I32 usdPimIntfNumHelloRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.1	Integer32	read-write	Total number of Hellos received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumJoinPruneRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.2	Integer32	read-write	Total number of JoinPrunes received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumAssertRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.3	Integer32	read-write	Total number of Asserts received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumGraftRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.4	Integer32	read-write	Total number of Grafts received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumGraftAckRcvd	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.5	Integer32	read-write	Total number of Graft Acks received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumHelloSent	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.6	Integer32	read-write	Total number of Hellos sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumJoinPruneSent	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.7	Integer32	read-write	Total number of JoinPrunes sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumAssertSent	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.8	Integer32	read-write	Total number of Asserts sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumGraftSent	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.9	Integer32	read-write	Total number of Grafts sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
I32 usdPimIntfNumGraftAckSent	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.10	Integer32	read-write	Total number of Graft Acks sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
INT usdPimIntfVersion	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.11	INTEGER	read-only	The version of PIM running on this interface.
I32 usdPimIntfNumNbrs	1.3.6.1.4.1.4874.2.2.43.1.1.11.1.12	Integer32	read-only	Number of PIM neighbors detected on this interface.
usdPimMRouteTable	1.3.6.1.4.1.4874.2.2.43.1.1.12		not-accessible	The (conceptual) table listing PIM multicast routing information describing its / / states.
usdPimMRouteEntry	1.3.6.1.4.1.4874.2.2.43.1.1.12.1		not-accessible	An entry (conceptual row) in the usdPimMRouteTable.
IP usdPimMRouteGroup	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.1	IpAddress	not-accessible	The group address. Specified as 224.0.0.0 for entries.
IP usdPimMRouteSource	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.2	IpAddress	not-accessible	The source address. Specified as 0.0.0.0 for and entries.
IP usdPimMRouteSourceMask	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.3	IpAddress	not-accessible	The source address mask. Specified as 255.255.255.255 for entries and 0.0.0.0 for and entries.
IP usdPimMRouteRPAddress	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.4	IpAddress	not-accessible	The RP address used for . Specified as 0.0.0.0 for and entries.
TIK usdPimMRouteUpstreamAssertTimer	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.5	TimeTicks	read-only	The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert has changed the upstream neighbor away from the RPF neighbor.
I32 usdPimMRouteAssertMetric	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.6	Integer32	read-only	The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received.
I32 usdPimMRouteAssertPref	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.7	Integer32	read-only	The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect.
T/F usdPimMRouteAssertRPTBit	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.8	TruthValue	read-only	The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect.
BIT usdPimMRouteBits	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.9	Bits	read-only	This object describes whether the entry is on shared tree (rpt) or shortest path tree (spt).
IP usdPimMRouteRPAddrInUse	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.10	IpAddress	read-only	The RP Address being used for the RPT// entries. Set to 0.0.0.0 for entries on shortest path tree.
IP usdPimMRouteUpstreamNbr	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.11	IpAddress	read-only	The address of upstream neighbor being used for the entry. Its set to 0.0.0.0 if the router is directly attached to source on one of its interface.
IP usdPimMRouteIifAddr	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.12	IpAddress	read-only	The address of incoming interface for this entry.
T/F usdPimMRouteIsWaitingToSwitchToSPT	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.13	TruthValue	read-only	This object describes whether the entry is still waiting to switch completely to shortest path tree in case of entries. It waits to do this till it receives first packet from incoming interface towards shortest path tree.
TIK usdPimMRouteEntryExpiryTimer	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.14	TimeTicks	read-only	The time after which the entry timer expires for this entry. Set to 0 if entry timer is not active.
IP usdPimMRouteSenderDRAddr	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.15	IpAddress	read-only	The address of the designated router on the sender's subnet in case of entries. The sender designated router register encapsulates data to RP. Set to 0.0.0.0 for and entries.
IP usdPimMRouteRouteAddr	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.16	IpAddress	read-only	The address of the route being used to do RPF check for this entry. It is set to 0.0.0.0 (with usdPimMRouteRouteMask set to 255.255.255.255) if there is no route available.
IP usdPimMRouteRouteMask	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.17	IpAddress	read-only	The mask of the route being used to do RPF check for this entry. It is set to 255.255.255.255 (with usdPimMRouteRoute set to 0.0.0.0) if there is no route available.
IP usdPimMRouteGRPAddr	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.18	IpAddress	read-only	The address of the group-to-RP mapping being used to get the RP for this entry. It is set to 0.0.0.0 (with usdPimMRouteGRPMask set to 0.0.0.0) if there is no group-to-RP mapping available or if entry is .
IP usdPimMRouteGRPMask	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.19	IpAddress	read-only	The mask of the group-to-RP mapping being used to get the RP for this entry. It is set to 255.255.255.255 (with usdPimMRouteGRPAddr set to 0.0.0.0) if there is no group-to-RP mapping available or if entry is .
T/F usdPimMRouteOtherProtoOifJoinTypeAll	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.20	TruthValue	read-only	This object indicates if some other multicast protocol is also interested in receiving data for this entry as a result of its interest in receiving all data. This will be particularly true for dense mode protocols which would want all data () from PIM sparse mode protocol.
T/F usdPimMRouteOtherProtoOifJoinTypeG	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.21	TruthValue	read-only	This object indicates if some other multicast protocol is also interested in receiving data for this entry as a result of its interest in receiving data for a given group. This will be particularly true for IGMP which would want data for a given group () from PIM protocol.
T/F usdPimMRouteOtherProtoOifJoinTypeSG	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.22	TruthValue	read-only	This object indicates if some other multicast protocol is also interested in receiving data for this entry as a result of its interest in receiving data for a given . This will be particularly true for IGMPv3 which would want data for a given ) from PIM sparse-mode protocol.
USD usdPimMRoutePimType	1.3.6.1.4.1.4874.2.2.43.1.1.12.1.23	UsdPimType	read-only	This object indicates if the owner of this entry is Sparse mode or Dense mode PIM. Owner is usually determined by the protocol running on the incoming interface of the entry. In case sparse-dense mode PIM is running on the incoming interface, sparse-mode is the owner if RP for the group is known, else dense mode is the owner.
usdPimMRouteNextHopTable	1.3.6.1.4.1.4874.2.2.43.1.1.13		not-accessible	The (conceptual) table listing PIM multicast routing information describing its / / outgoing interfaces.
usdPimMRouteNextHopEntry	1.3.6.1.4.1.4874.2.2.43.1.1.13.1		not-accessible	An entry (conceptual row) in the usdPimMRouteNextHopTable.
IP usdPimMRouteNextHopGroupAddr	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.2	IpAddress	not-accessible	The group address. Specified as 224.0.0.0 for entries.
IP usdPimMRouteNextHopSrcAddr	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.3	IpAddress	not-accessible	The source address. Specified as 0.0.0.0 for and entries.
IP usdPimMRouteNextHopSrcMask	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.4	IpAddress	not-accessible	The source address mask. Specified as 255.255.255.255 for entries and 0.0.0.0 for and entries.
IP usdPimMRouteNextHopRPAddr	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.5	IpAddress	not-accessible	The RP address used for . Specified as 0.0.0.0 for and entries.
NUM usdPimMRouteNextHopIfId	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.6	InterfaceIndex	not-accessible	The interface index of the outgoing interface (next hop). Specified as 0 for register outgoing interface. Register outgoing interfaces are created by DR on the source subnet to send PIM register encapsulated data (as unicast) to RP. It is also used by PIM boundary routers (PMBRs) to register data to RP.
IP usdPimMRouteNextHopAddress	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.7	IpAddress	not-accessible	This object takes following different values based on the type of next hop. It should be set to the address of RP in case the next hop interface is register interface i.e. usdPimMRouteNextHopIfId object is set to 0. It should be set to the address of neighbor in case the interface is an NBMA interface. In all other cases it should be set to the group address itself.
INT usdPimMRouteNextHopPruneReason	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.8	INTEGER	read-only	This object indicates why the downstream interface was pruned, whether in response to a PIM prune message or due to PIM Assert processing.
T/F usdPimMRouteNextHopJoinTypeSSRP	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.9	TruthValue	read-only	This object indicates whether or not the interface was added as a result of receiving join in case of entry OR inherited as outgoing interface from corresponding entry in case of entry.
T/F usdPimMRouteNextHopJoinTypeG	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.10	TruthValue	read-only	This object indicates whether or not the interface was added as a result of receiving join in case of entry OR inherited as outgoing interface from corresponding entry in case of entry.
T/F usdPimMRouteNextHopJoinTypeSG	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.11	TruthValue	read-only	This object indicates whether or not the interface was added as a result of receiving join in case of entry.
T/F usdPimMRouteNextHopHasLGM	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.12	TruthValue	read-only	This object indicates whether or not the interface has local group membership (as indicated by IGMP) in case of and entries.
T/F usdPimMRouteNextHopHasOifAW	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.13	TruthValue	read-only	This object indicates whether or not this interface is the winner of assert for corresponding / entry.
T/F usdPimMRouteNextHopHasOifSendAssert	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.14	TruthValue	read-only	This object indicates whether or not this interface is going to send an assert at the end of assert suppression interval. Assert suppression is used to prevent a flood of assert to be generated in response to data or other asserts.
T/F usdPimMRouteNextHopHasOifRegister	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.15	TruthValue	read-only	This object indicates whether or not this next hop is a register outgoing interface.
T/F usdPimMRouteNextHopHasOifBorderBit	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.16	TruthValue	read-only	This object is used to describe a register outgoing interface. It indicates whether or not the border bit is set in the register packet when the packet is sent over the register interface. For all other (non-register) interfaces its set to false.
T/F usdPimMRouteNextHopHasOifNullEncapsBit	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.17	TruthValue	read-only	This object is used to describe a register outgoing interface. It indicates whether or not the NULL encapsulation bit is set (periodically) in the register packet when the packet is sent over the register interface. For all other (non-register) interfaces its set to false.
TIK usdPimMRouteNextHopJoinEndTimer	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.18	TimeTicks	read-only	This object indicates the time (in seconds) left when the join timer expires for the outgoing interface. Join timer for an outgoing interface of entry indicates when the join expires, for a entry indicates when the join expires and for a entry indicates when the join expires. Inherited joins (like inheriting from AND inheriting from ) expire when the corresponding parent join expires.
TIK usdPimMRouteNextHopAssertEndTimer	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.19	TimeTicks	read-only	This object indicates the time (in seconds) left when the assert timer expires on this outgoing inteface.
TIK usdPimMRouteNextHopNextAssertTimer	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.20	TimeTicks	read-only	This object indicates the duration (in seconds) left for which sending an assert has been suppressed on this outgoing interface.
IP usdPimMRouteNextHopAssertSrcAddress	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.21	IpAddress	read-only	This object indicates the source address which will be used in the assert packet to send an assert out for the entry on this outgoing interface. For entries it is the address of the source S itself. For entries it is the address of the source whose data was forwarded using this and caused the assert situation to happen.
TIK usdPimMRouteNextHopRegisterSuppressionTimer	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.22	TimeTicks	read-only	This object is used for register outgoing interfaces. It indicates the duration (in seconds) left for which sending a register packet has been suppressed on the register outgoing interface as a result of receiving register-stop from the RP.
USD usdPimMRouteNextHopPimType	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.23	UsdPimType	read-only	This object indicates whether the outgoing interface was contributed by sparse-mode or dense-mode PIM.
TIK usdPimMRouteNextHopPruneTimeLeft	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.24	TimeTicks	read-only	This object indicates the time (in seconds) left when the prune timer expires on an outgoing inteface. Its used for pruned outgoing interfaces contributed by dense-mode PIM.
IP usdPimMRouteNextHopsendingIpAddress	1.3.6.1.4.1.4874.2.2.43.1.1.13.1.25	IpAddress	read-only	This object describes the source IP address used by this interface to send PIM packets out on this outgoing interface.
usdPimRPSetTable	1.3.6.1.4.1.4874.2.2.43.1.1.14		not-accessible	The (conceptual) table listing enterprise specific information on a subset of the rows of the pimRPSetTable defined in the standard PIM MIB.
usdPimRPSetEntry	1.3.6.1.4.1.4874.2.2.43.1.1.14.1		not-accessible	An entry (conceptual row) in the usdPimRPSetTable.
I32 usdPimRPSetPriority	1.3.6.1.4.1.4874.2.2.43.1.1.14.1.1	Integer32	read-only	This object describes the priority of the RP for this group-to-RP mapping.
INT usdPimRPSetTypeInfo	1.3.6.1.4.1.4874.2.2.43.1.1.14.1.2	INTEGER	read-only	This object describes the mechanism by which this group to RP mapping has been learnt, i.e. whether its statically configured, AutoRP learnt or BSR learnt. It also indicates whether the mapping is positive or negative. Negative mappings force the groups in that range to fall into dense-mode category if sparse-dense mode is configured or no RP if its purely sparse mode configuration.
OCT usdPimRPSetAccessListName	1.3.6.1.4.1.4874.2.2.43.1.1.14.1.3	OCTET STRING	read-only	This object lists the name of the access list from which this group-to-RP mapping was picked up in case of statically configured RPs.
usdPimStaticRPConfTable	1.3.6.1.4.1.4874.2.2.43.1.1.15		not-accessible	The (conceptual) table listing statically configured PIM RPs.
usdPimStaticRPConfEntry	1.3.6.1.4.1.4874.2.2.43.1.1.15.1		not-accessible	An entry (conceptual row) in the usdPimStaticRPConfTable.
I32 usdPimStaticRPConfComponentIndex	1.3.6.1.4.1.4874.2.2.43.1.1.15.1.1	Integer32	not-accessible	A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
IP usdPimStaticRPConfRPAddr	1.3.6.1.4.1.4874.2.2.43.1.1.15.1.2	IpAddress	not-accessible	Ip address of the RP which for the group-to-RP mapping being configured.
OCT usdPimStaticRPConfAccessListName	1.3.6.1.4.1.4874.2.2.43.1.1.15.1.3	OCTET STRING	not-accessible	Name of the access list from which group-ranges are picked up for this group-ro-RP mapping. Every deny component in the list is added as negative group-ro-RP mapping.
ROW usdPimStaticRPConfRowStatus	1.3.6.1.4.1.4874.2.2.43.1.1.15.1.4	RowStatus	read-create	The status of this row, by which new entries may be created, or old entries deleted from this table.
T/F usdPimStaticRPConfOverride	1.3.6.1.4.1.4874.2.2.43.1.1.15.1.5	TruthValue	read-create	The object indicates whether or not this statically configured group-to-RP mapping should override the group-to-RP mapping learnt via AutoRP for the component group-ranges in the access list. By default AutoRP learnt group-to-RP mappings are preferred over statically configured ones. While setting the rowStatus to create a static RP, this field should be assigned to true if the override property is desired.
usdPimAutoRPConfTable	1.3.6.1.4.1.4874.2.2.43.1.1.16		not-accessible	The (conceptual) table allowing AutoRP configuration of candidate RPs (advertisement agents).
usdPimAutoRPConfEntry	1.3.6.1.4.1.4874.2.2.43.1.1.16.1		not-accessible	An entry (conceptual row) in the usdPimAutoRPConfTable.
I32 usdPimAutoRPConfComponentIndex	1.3.6.1.4.1.4874.2.2.43.1.1.16.1.1	Integer32	not-accessible	A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
IP usdPimAutoRPConfCandRPAddr	1.3.6.1.4.1.4874.2.2.43.1.1.16.1.2	IpAddress	not-accessible	The IP address of the candidate RP for this advertising agent configuration.
OCT usdPimAutoRPConfGroupAccessListName	1.3.6.1.4.1.4874.2.2.43.1.1.16.1.3	OCTET STRING	not-accessible	The access list name from which group ranges are picked up for advertising agent configuration.
ROW usdPimAutoRPConfRowStatus	1.3.6.1.4.1.4874.2.2.43.1.1.16.1.4	RowStatus	read-create	The status of this row, by which new entries may be created, or old entries deleted from this table.
I32 usdPimAutoRPConfTTL	1.3.6.1.4.1.4874.2.2.43.1.1.16.1.5	Integer32	read-create	The time-to-live value used while sending AutoRP advertisement out for this group-to-RP mappings created as a result of this configuration. This should be set along with usdPimAutoRPConfRowStatus while creating an AutoRP advertising agent to denote the TTL value to be used.
TIK usdPimAutoRPConfAncmntIntvl	1.3.6.1.4.1.4874.2.2.43.1.1.16.1.6	TimeTicks	read-create	The time interval at which AutoRP advertisements are sent out for the group-to-RP mappings created as a result of this configuration. This should be set along with usdPimAutoRPConfRowStatus while creating an AutoRP advertising agent to denote the announcement interval to be used.
NUM usdPimAutoRPConfifId	1.3.6.1.4.1.4874.2.2.43.1.1.16.1.7	InterfaceIndex	read-only	The interface index of the interface for the candidate RP if an interface with that address exists else it is set to 0.
usdPimAutoRPCandTable	1.3.6.1.4.1.4874.2.2.43.1.1.17		not-accessible	The (conceptual) table listing AutoRP candidate RPS (advertising agents).
usdPimAutoRPCandEntry	1.3.6.1.4.1.4874.2.2.43.1.1.17.1		not-accessible	An entry (conceptual row) in the usdPimAutoRPCandTable.
I32 usdPimAutoRPCandComponentIndex	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.1	Integer32	not-accessible	A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
IP usdPimAutoRPCandRPAddr	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.2	IpAddress	not-accessible	The IP address of the candidate RP for this group-to-RP mapping.
IP usdPimAutoRPCandGroupAddr	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.3	IpAddress	not-accessible	The group address of the candidate RP for this group-to-RP mapping.
IP usdPimAutoRPCandGroupMask	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.4	IpAddress	not-accessible	The group mask of the candidate RP for this group-to-RP mapping.
ROW usdPimAutoRPCandRowStatus	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.5	RowStatus	read-only	The current status of this row.
OCT usdPimAutoRPCandAccessListName	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.6	OCTET STRING	read-only	The name of the group list using which this AutoRP group-to-RP candidate RP mapping was configured.
I32 usdPimAutoRPCandAutoRPTTL	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.7	Integer32	read-only	The time-to-live value used while sending AutoRP advertisement out for this group-to-RP mapping.
TIK usdPimAutoRPCandAutoRPAncmntIntvl	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.8	TimeTicks	read-only	The time interval at which AutoRP advertisements are sent out for this group-to-RP mapping.
NUM usdPimAutoRPCandIfId	1.3.6.1.4.1.4874.2.2.43.1.1.17.1.9	InterfaceIndex	read-only	The interface index of the interface for this AutoRP group-to-RP candidate RP mapping if an interface for RP address exists else it is set to 0.
usdPimComponentTable	1.3.6.1.4.1.4874.2.2.43.1.1.18		not-accessible	The (conceptual) table listing each component (domain) in PIM.
usdPimComponentEntry	1.3.6.1.4.1.4874.2.2.43.1.1.18.1		not-accessible	An entry (conceptual row) in the usdPimComponentTable.
I32 usdPimComponentIndex	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.1	Integer32	not-accessible	A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
ROW usdPimComponentAutoRPMappingAgentRowStatus	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.2	RowStatus	read-create	The status of AutoRP mapping agent by which this router can be made an AutoRP mapping agent or removed from being an AutoRP mapping agent in this component.
NUM usdPimComponentConfiguredAutoRPMappingAgentIfId	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.3	InterfaceIndex	read-create	The interface index of the interface which mapping agent should use to send AutoRP mapping messages. If not specified, the interface with highest IP address in this domain is picked up for this purpose.
TIK usdPimComponentAutoRPMappingAgentInterval	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.4	TimeTicks	read-create	The time interval at which AutoRP mapping messages are sent out in this component. The default value is 60 seconds.
I32 usdPimComponentAutoRPMappingTTL	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.5	Integer32	read-create	The time-to-live value used while sending AutoRP mapping messages out in this component.
IP usdPimComponentAutoRPMappingAgentIntfAddr	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.6	IpAddress	read-only	The IP address of the interface which mapping agent is using to send AutoRP mapping messages.
IP usdPimComponentAutoRPMappingAgentWinnerAddr	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.7	IpAddress	read-only	The IP address of the winner AutoRP mapping agent. There can be multiple mapping agents configured in a given PIM domain(component). The mapping agent with highest IP address is chosen as the winner and it continues to send AutoRP mapping messages. If the router itself is the winner, then this is set to 0.0.0.0.
TIK usdPimComponentAutoRPMappingAgentWinnerLastHeard	1.3.6.1.4.1.4874.2.2.43.1.1.18.1.8	TimeTicks	read-only	The time (in seconds) that has past since an AutoRP mapping message was receieved from the winner AutoRP mapping agent. If the router itself is the winner, then this is set to 0.
usdPimUnicastRouteTable	1.3.6.1.4.1.4874.2.2.43.1.1.19		not-accessible	The (conceptual) table listing all the unicast routes currently in use by PIM for diong RPF checking.
usdPimUnicastRouteEntry	1.3.6.1.4.1.4874.2.2.43.1.1.19.1		not-accessible	An entry (conceptual row) in the usdPimUnicastRouteTable.
IP usdPimUnicastRouteEntryAddr	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.1	IpAddress	not-accessible	The address of route in use.
IP usdPimUnicastRouteEntryMask	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.2	IpAddress	not-accessible	The mask of route in use.
IP usdPimUnicastRouteEntryRpfNbr	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.3	IpAddress	read-only	The RPF neighbor (next-hop) to reach the route of this entry. It is set to 0.0.0.0 for directly connected routes.
NUM usdPimUnicastRouteEntryIifId	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.4	InterfaceIndex	read-only	The interface index (next-hop) to reach the route of this entry.
IP usdPimUnicastRouteEntryIifAddr	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.5	IpAddress	read-only	The interface address (next-hop) to reach the route of this entry.
I32 usdPimUnicastRouteEntryPref	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.6	Integer32	read-only	The preference of the route of this entry.
I32 usdPimUnicastRouteEntryMetric	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.7	Integer32	read-only	The metric of the route of this entry.
USD usdPimUnicastRouteEntryPimType	1.3.6.1.4.1.4874.2.2.43.1.1.19.1.8	UsdPimType	read-only	This object indicates whether the route specified in this entry is being used by sparse-mode and/or dense-mode PIM.
usdPimSPTThresholdTable	1.3.6.1.4.1.4874.2.2.43.1.1.20		not-accessible	The (conceptual) table listing threshold values set for switching from shared tree to shortest path tree and vice versa for data forwarded by PIM sparse-mode.
usdPimSPTThresholdEntry	1.3.6.1.4.1.4874.2.2.43.1.1.20.1		not-accessible	An entry (conceptual row) in the usdPimSPTThresholdTable.
OCT usdPimSPTThresholdAccessListName	1.3.6.1.4.1.4874.2.2.43.1.1.20.1.1	OCTET STRING	not-accessible	The name of the access list from which group ranges are picked up for setting SPT threshold in this entry.
ROW usdPimSPTThresHoldRowStatus	1.3.6.1.4.1.4874.2.2.43.1.1.20.1.2	RowStatus	read-write	The status of this row, by which new entries may be created, or old entries deleted from this table.
I32 usdPimSPTThresholdKbps	1.3.6.1.4.1.4874.2.2.43.1.1.20.1.3	Integer32	read-write	The value of SPT threshold in kilobits per second. Default value is 0.
usdPimConformance	1.3.6.1.4.1.4874.2.2.43.2
usdPimCompliances	1.3.6.1.4.1.4874.2.2.43.2.1
usdPimCompliance	1.3.6.1.4.1.4874.2.2.43.2.1.1			The compliance statement for entities which implement the Unisphere PIM MIB.
usdPimGroups	1.3.6.1.4.1.4874.2.2.43.2.2
usdPimGeneralGroup	1.3.6.1.4.1.4874.2.2.43.2.2.1			A collection of objects for managing general PIM capabilities in a Unisphere product.
usdPimInterfaceGroup	1.3.6.1.4.1.4874.2.2.43.2.2.2			A collection of objects for managing PIM interface capabilities in a Unisphere product.
usdPimMRouteConfGroup	1.3.6.1.4.1.4874.2.2.43.2.2.3			A collection of objects for managing PIM multicast route capabilities in a Unisphere product.
usdPimMRouteNextHopGroup	1.3.6.1.4.1.4874.2.2.43.2.2.4			A collection of objects for managing PIM multicast route next hop capabilities in a Unisphere product.
usdPimRPSetGroup	1.3.6.1.4.1.4874.2.2.43.2.2.5			A collection of objects for managing PIM RP-Set capabilities in a Unisphere product.
usdPimStaticRPConfGroup	1.3.6.1.4.1.4874.2.2.43.2.2.6			A collection of objects for managing statically configured PIM RPs capabilities in a Unisphere product.
usdPimAutoRPConfGroup	1.3.6.1.4.1.4874.2.2.43.2.2.7			A collection of objects for managing PIM AutoRP candidate advertisment agent RP capabilities in a Unisphere product.
usdPimAutoRPCandGroup	1.3.6.1.4.1.4874.2.2.43.2.2.8			A collection of objects for managing PIM AutoRP candidate advertising agent RP capabilities in a Unisphere product.
usdPimComponentGroup	1.3.6.1.4.1.4874.2.2.43.2.2.9			A collection of objects for managing PIM component (domain) capabilities in a Unisphere product.
usdPimUnicastRouteGroup	1.3.6.1.4.1.4874.2.2.43.2.2.10			A collection of objects for managing PIM unicast route capabilities in a Unisphere product.
usdPimSPTThresholdGroup	1.3.6.1.4.1.4874.2.2.43.2.2.11			A collection of objects for managing PIM shortest path tree threshold capabilities in a Unisphere product.

RFC description

Unisphere Networks PIM (Protocol Independent Multicast) router MIB for managing sparse and dense mode PIM routing.

Start monitoring Unisphere/Juniper ERX multicast-enabled router (PIM Hello/Join-Prune/Assert counter status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Unisphere-Data-PIM-MIB