All MIBs › TROPIC-POWERMGMT-MIB
Organization: Nokia
Last Updated: 2015-11-04
Category: Nokia Optical Transport
Description: Monitors Nokia Tropic power management including supply status, consumption, and redundancy.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TROPIC-POWERMGMT-MIB?
TROPIC-POWERMGMT-MIB is a vendor-specific module from Nokia (formerly Tropic Networks) that models power management for optical transport network elements, covering power supply status, power consumption, and power redundancy. It exposes hardware environmental data specific to the power subsystem of a chassis, rather than networking protocol state. This MIB is explicitly geared toward monitoring hardware health: it lets an administrator track power supply operational/failure status, measure power draw per shelf or module, and verify that redundant power feeds are both active, directly supporting alerting on power supply faults that could lead to an outage. As a power-management MIB it likely complements the vendor's broader chassis/environment MIBs (temperature, fan) though no explicit cross-MIB dependency is stated in the description. It is typically deployed on Tropic/Nokia optical transport shelves in central-office or metro network sites where power redundancy is critical for service continuity, making TROPIC-POWERMGMT-MIB SNMP monitoring a key part of proactive power-fault alerting.
IPNetwork Monitor allows you to monitor SNMP objects defined in TROPIC-POWERMGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia (formerly Tropic Networks) optical transport chassis
- optical network element power subsystem
Monitoring Examples
An operator would poll power-supply status and consumption objects in this MIB for each power feed in a chassis to confirm both A and B feeds are active and drawing expected current, alerting if one feed's status transitions to failed. Watching power consumption trends over time could also reveal a card drawing abnormally high current, an early indicator of a failing power converter. No sample objects were supplied for this MIB, so this description is grounded in its stated power-management purpose.
What Can Be Monitored
- power supply operational status
- power supply failure/fault state
- power consumption
- power feed redundancy status
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex | |
| ifIndex | OBJECT-TYPE |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From TROPIC-GLOBAL-REG
| tnPowerMgmtMIB | OBJECT-IDENTITY |
| tnSystemModules | OBJECT-IDENTITY |
From TROPIC-SHELF-MIB
| tnShelfIndex | OBJECT-TYPE |
From TROPIC-SLOT-MIB
| tnSlotIndex | OBJECT-TYPE |
From TROPIC-TC
| AluWdmOtuBitRate | |
| AluWdmOtuEncoding | |
| TnCommand |
From TROPIC-WAVEKEY-MIB
| tnChannel | OBJECT-TYPE |
| tnDirection | OBJECT-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tnPowerMgmtMibModule | 1.3.6.1.4.1.7483.1.1.2.1.7 | The power management MIB. | ||
| tnPowerMgmtConf | 1.3.6.1.4.1.7483.2.1.6.1 | |||
| tnPowerMgmtGroups | 1.3.6.1.4.1.7483.2.1.6.1.1 | |||
| tnPowerMgmtGlobalGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.1 | |||
| tnPowerMgmtControlGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.2 | |||
| tnPowerMgmtIngressGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.4 | |||
| tnPowerMgmtEgressGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.5 | |||
| tnPowerMgmtPortGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.7 | |||
| tnPowerMgmtPowerOffsetInGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.9 | |||
| tnPowerMgmtPowerOffsetOutGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.10 | |||
| tnPowerMgmtIngressPerChannelGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.11 | |||
| tnPowerMgmtEgressPerChannelGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.12 | |||
| tnPowerMgmtTechnologyTypesGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.13 | |||
| tnPowerMgmtAnyAddGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.14 | |||
| tnPowerMgmtAnyDropGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.15 | |||
| tnPowerMgmtIroadmScalarsGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.16 | |||
| tnPowerMgmtIroadmGroup | 1.3.6.1.4.1.7483.2.1.6.1.1.17 | |||
| tnPowerMgmtCompliances | 1.3.6.1.4.1.7483.2.1.6.1.2 | |||
| tnPowerMgmtCompliance | 1.3.6.1.4.1.7483.2.1.6.1.2.1 | |||
| tnPowerMgmtObjs | 1.3.6.1.4.1.7483.2.1.6.2 | |||
| tnPowerMgmtBasics | 1.3.6.1.4.1.7483.2.1.6.2.1 | |||
| tnPowerMgmtGlobal | 1.3.6.1.4.1.7483.2.1.6.2.1.1 | |||
| U32 tnPowerMgmtGlobalMinStepSize | 1.3.6.1.4.1.7483.2.1.6.2.1.1.2 | Unsigned32 | read-write | If the change in power for a given wavelength calculated over one auto power adjustment control loop pass is less than the value of this attribute, no change in power will be executed. Sets are not supported. |
| U32 tnPowerMgmtGlobalMaxStepSize | 1.3.6.1.4.1.7483.2.1.6.2.1.1.3 | Unsigned32 | read-write | The maximum change in power per wavelength permitted over one auto power adjustment control loop pass. Sets are not supported. |
| TNC tnPowerMgmtGlobalResetToDefaults | 1.3.6.1.4.1.7483.2.1.6.2.1.1.4 | TnCommand | read-write | When read, the value of this attribute is always noCmd. Sets are not supported. |
| T/F tnPowerMgmtGlobalAutoEnabled | 1.3.6.1.4.1.7483.2.1.6.2.1.1.5 | TruthValue | read-write | Indicates if the automatic functioning of power management is enabled. Sets are not supported. |
| U32 tnPowerMgmtGlobalNumberOfAutoPowerAdjPoints | 1.3.6.1.4.1.7483.2.1.6.2.1.1.6 | Unsigned32 | read-only | The current number of auto power adjustment points. |
| T/F tnPowerMgmtGlobalAlarmWhenDisabled | 1.3.6.1.4.1.7483.2.1.6.2.1.1.7 | TruthValue | read-write | Indicates if the automatic power management disabled alarm will be raised when auto power management is disabled. Sets are not supported. |
| tnPowerMgmtControlTable | 1.3.6.1.4.1.7483.2.1.6.2.1.2 | not-accessible | This table provides access to auto power adjustment operation execution and status. | |
| tnPowerMgmtControlEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.2.1 | not-accessible | ||
| INT tnPowerMgmtDirection | 1.3.6.1.4.1.7483.2.1.6.2.1.2.1.1 | INTEGER | not-accessible | The signal direction. |
| TRO tnPowerMgmtControlPercentCompleted | 1.3.6.1.4.1.7483.2.1.6.2.1.2.1.3 | TropicPowerMgmtPercentCompleted | read-only | The percent completion of this auto power adjustment operation. Only applies when tnPowerMgmtControlStatus is inProgress. It should be 0 at all other times. |
| ROW tnPowerMgmtControlRowStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.2.1.5 | RowStatus | read-create | The following is a breakdown of each of the supported values: active - (r) auto power adjustment operating at this point. notInService - (r) auto power adjustment not operating at this point. |
| tnPowerMgmtIngressTable | 1.3.6.1.4.1.7483.2.1.6.2.1.4 | not-accessible | The attributes in this table must not be set together with the same index in the same set request PDU. | |
| tnPowerMgmtIngressEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1 | not-accessible | ||
| INT tnPowerMgmtIngressAdjustPowerGain | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.1 | INTEGER | read-create | Value executeWithForce is no longer supported. |
| TRO tnPowerMgmtIngressAdjustPowerGainLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.2 | TropicPowerMgmtResult | read-only | The result of the last executed power gain adjustment operation. |
| INT tnPowerMgmtIngressAcceptPowers | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.3 | INTEGER | read-create | Value executeWithClear is no longer supported. Sets with this value will be failed back to the network operator. |
| TRO tnPowerMgmtIngressAcceptPowersLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.4 | TropicPowerMgmtResult | read-only | The result of the last executed power acceptance operation. |
| I32 tnPowerMgmtIngressRippleAllowance | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.5 | Integer32 | read-create | The ripple allowance. |
| U32 tnPowerMgmtIngressAdjustPowerGainTargetGain | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.6 | Unsigned32 | read-only | |
| TRO tnPowerMgmtIngressAdjustPowerGainStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.7 | TropicPowerMgmtStatus | read-only | This attribute indicates the status of the executed power gain adjustment operation. |
| TNC tnPowerMgmtIngressStartAseAdjust | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.8 | TnCommand | read-create | Start Amplified Spontaneous Emissions adjustment. Get requests always return a value of noCmd. |
| TRO tnPowerMgmtIngressAseAdjustLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.9 | TropicPowerMgmtResult | read-only | The result of the last executed ASE adjustment. |
| TRO tnPowerMgmtIngressAseAdjustStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.10 | TropicPowerMgmtStatus | read-only | This attribute indicates the status of the executed ASE adjustment operation. |
| T/F tnPowerMgmtIngressCommissioned | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.11 | TruthValue | read-only | This attribute indicates if the ingress adjustment point has done a successful adjustment following being in an un-commissioned state. true - Adjusted successfully. false - NE event has caused the previous adjustment to be invalidated. |
| I32 tnPowerMgmtIngressGainSetOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.12 | Integer32 | read-create | Value added to result of gain adjustment calculation. Current configurable range: -300 to 300. |
| I32 tnPowerMgmtIngressCommissionedGain | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.13 | Integer32 | read-only | Gain value set while commissioning flag is false. Current range: AHPHG: 0 to 3300 ALPHG: 0 to 3000 AHPLG: 0 to 2400 ALPFGK: 0 to 2300 ALPFGT: 0 to 2300 A2325A: 0 to 3200 AM2325B: 0 to 3200 AM2017B: 0 to 2400 |
| I32 tnPowerMgmtIngressSRSTiltPostFraction | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.14 | Integer32 | read-create | Used to modify the fraction of upstream span SRS tilt post compensated. Current configurable range: 0 to 300. |
| TRO tnPowerMgmtIngressSRSTiltAdjResult | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.15 | TropicPowerMgmtResult | read-only | Result string describing outcome of the tilt adjustment. |
| ALU tnPowerMgmtIngressSRSTiltAdjStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.16 | AluWdmPowerMgmtSRSTiltAdjStatus | read-only | Status of the tilt adjustment. |
| T/F tnPowerMgmtIngressPassed | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.17 | TruthValue | read-only | Indicates the optimization adjustment failed or passed. |
| I32 tnPowerMgmtIngressSRSTiltCalcOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.18 | Integer32 | read-only | Indicates if the LD setting has been offset to compensate downstream TiltMismatch. Range: -500 to 500. |
| I32 tnPowerMgmtIngressInternodalOaPpcMaxInCurrent | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.19 | Integer32 | read-only | Current range: -9900, -2000 to 0. |
| I32 tnPowerMgmtIngressInternodalOaPpcMaxInReference | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.20 | Integer32 | read-only | Current range: -9900, -2000 to 0. |
| I32 tnPowerMgmtIngressInternodalCalculatedSpanLossInCurrent | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.21 | Integer32 | read-only | Current range: -9900, 0 to 4000. |
| I32 tnPowerMgmtIngressInternodalCalculatedSpanLossInReference | 1.3.6.1.4.1.7483.2.1.6.2.1.4.1.22 | Integer32 | read-only | Current range: -9900, 0 to 4000. |
| tnPowerMgmtEgressTable | 1.3.6.1.4.1.7483.2.1.6.2.1.5 | not-accessible | The attributes in this table must not be set together with the same index in the same set request PDU. | |
| tnPowerMgmtEgressEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1 | not-accessible | ||
| TNC tnPowerMgmtEgressAdjustPowerWithOptimization | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.1 | TnCommand | read-create | |
| TRO tnPowerMgmtEgressAdjustPowerWithOptimizationStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.2 | TropicPowerMgmtStatus | read-only | This attribute indicates the status of the executed power with optimization adjustment operation. |
| TNC tnPowerMgmtEgressAdjustPowerWithOptimizationAbort | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.3 | TnCommand | read-create | This attribute allows the network operator to submit an abort on the currently executing power with optimization adjustment operation. When read back, the value of this attribute is noCmd. |
| TNC tnPowerMgmtEgressAcceptPowers | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.4 | TnCommand | read-create | |
| TRO tnPowerMgmtEgressAdjustPowerWithOptimizationLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.6 | TropicPowerMgmtResult | read-only | The result of the last executed power adjustment with optimization operation. |
| TRO tnPowerMgmtEgressAcceptPowersLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.7 | TropicPowerMgmtResult | read-only | The result of the last executed power acceptance operation. |
| U32 tnPowerMgmtEgressAdjustPowerWithOptimizationTargetGain | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.9 | Unsigned32 | read-only | |
| TNC tnPowerMgmtEgressStartAseAdjust | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.10 | TnCommand | read-create | Start Amplified Spontaneous Emissions adjustment. Get requests always return a value of noCmd. |
| TNC tnPowerMgmtEgressStopAseAdjust | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.11 | TnCommand | read-create | Stop Amplified Spontaneous Emissions adjustment. Get requests always return a value of noCmd. |
| TRO tnPowerMgmtEgressAseAdjustLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.12 | TropicPowerMgmtResult | read-only | The result of the last executed ASE adjustment. |
| TRO tnPowerMgmtEgressAseAdjustStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.13 | TropicPowerMgmtStatus | read-only | This attribute indicates the status of the executed ASE adjustment operation. |
| T/F tnPowerMgmtEgressCommissioned | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.14 | TruthValue | read-only | This attribute indicates if the egress adjustment point has done a successful adjustment following being in an un-commissioned state. true - Adjusted successfully. false - NE event has caused the previous adjustment to be invalidated. |
| NUM tnPowerMgmtEgressAmpIfIndex | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.15 | InterfaceIndex | read-only | |
| NUM tnPowerMgmtEgressWssIfIndex | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.16 | InterfaceIndex | read-only | |
| I32 tnPowerMgmtEgressSRSTiltCalcMultiplier | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.17 | Integer32 | read-create | This is used to modify the calculated SRS tilt of the span. Current configurable range: 0 to 300. |
| I32 tnPowerMgmtEgressSRSTiltPreFraction | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.18 | Integer32 | read-create | This is used to modify the fraction of following span SRS tilt pre compensated. Current configurable range: 0 to 300. |
| I32 tnPowerMgmtEgressSRSTiltCalcACoeff | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.19 | Integer32 | read-create | Modeling coefficient for the SRSTilt = A*Pout(mW) equation. Current configurable range: 0 to 10000. |
| I32 tnPowerMgmtEgressSRSTiltCalcOutputLoss | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.20 | Integer32 | read-create | Configurable loss from the egress Line Out to the fiber span input. Current configurable range: 0 to 1700. |
| TRO tnPowerMgmtEgressSRSTiltAdjResult | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.22 | TropicPowerMgmtResult | read-only | Result string describing outcome of the tilt adjustment. |
| ALU tnPowerMgmtEgressSRSTiltAdjStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.23 | AluWdmPowerMgmtSRSTiltAdjStatus | read-only | Status of the tilt adjustment. |
| T/F tnPowerMgmtEgressPassed | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.24 | TruthValue | read-only | Indicates the optimization adjust failed or passed. |
| I32 tnPowerMgmtEgressLHLaunchAtten | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.25 | Integer32 | read-create | Added to the nominal attenuation lookup by WSS containing pack. Only applies to connectivity block in directionless architecture. Current configurable range: 0 to 1000. |
| U32 tnPowerMgmtFiberSpanTiltPreComp | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.27 | Unsigned32 | read-create | Amount of fiber span tilt to pre compensate. May not equal to tnPowerMgmtPortFiberSpanTilt. Current configurable range: 0 to 300. |
| I32 tnPowerMgmtEgressInternodalPpcMaxInDownstream | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.28 | Integer32 | read-only | Current range: -9900, -2000 to 0. |
| I32 tnPowerMgmtEgressInternodalSpanLossInDownstream | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.29 | Integer32 | read-only | Current range: -9900, 0 to 4000. |
| I32 tnPowerMgmtEgressInternodalPpcMaxInDownstreamReference | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.30 | Integer32 | read-only | Current range: -9900, -2000 to 0. |
| I32 tnPowerMgmtEgressInternodalSpanLossInDownstreamReference | 1.3.6.1.4.1.7483.2.1.6.2.1.5.1.31 | Integer32 | read-only | Current range: -9900, 0 to 4000. |
| tnPowerMgmtPortTable | 1.3.6.1.4.1.7483.2.1.6.2.1.7 | not-accessible | ||
| tnPowerMgmtPortEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1 | not-accessible | ||
| T/F tnPowerMgmtPortIsCommissioned | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.1 | TruthValue | read-create | Each external LD port whose power management mode setting is Automatic has a Power Management Commissioned Flag. When commissioning is completed these flags are set to complete (true) by users. |
| TRO tnPowerMgmtPortTypeIn | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.2 | TropicPowerMgmtType | read-create | The type of power management ingress. |
| TRO tnPowerMgmtPortTypeOut | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.3 | TropicPowerMgmtType | read-create | The type of power management egress. |
| ALU tnPowerMgmtPortWTDecoderUsageTypeIn | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.6 | AluWdmWTDecoderUsageType | read-create | The type of WTD used ingress. |
| ALU tnPowerMgmtPortWTDecoderUsageTypeOut | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.7 | AluWdmWTDecoderUsageType | read-create | The type of WTD used egress. |
| I32 tnPowerMgmtPortGainAdjSchedBase | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.8 | Integer32 | read-create | This is used to enter the base period past the hour for scheduled ingress adjustments. The unit is in 100s of ms. Value of -1 means not configured. Current configurable range: -1 to 863999. |
| I32 tnPowerMgmtPortGainAdjTimerPeriod | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.9 | Integer32 | read-create | This is used to enter the timer length between enablements for the OMS section. The unit is in 100s of ms. Value of -1 means not configured. Current configurable range: -1 to 863999. |
| I32 tnPowerMgmtPortGainAdjTimerLength | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.10 | Integer32 | read-create | This is used to enter the length of enablement time for the OMS section. The unit is in 100s of ms. Value of -1 means not configured. Current configurable range: -1 to 35999. |
| T/F tnPowerMgmtPortInGainAdjAutoEnabled | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.11 | TruthValue | read-create | This is used to configure line behaviour: false - no auto adjusts, true - will enable adjustments, or do auto adjustments. |
| T/F tnPowerMgmtPortSRSTiltAdjAutoEnabled | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.12 | TruthValue | read-create | If this value is true and line is OADM, controls updates of the channel set information used for SRS Adjustment. Value automatically updates at lines that pull the channel information from upstream. |
| U32 tnPowerMgmtPortFiberSpanTilt | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.13 | Unsigned32 | read-create | Linear fit of attenuation vs FREQ across defined channel min, max for tnPowerMgmtFiberSpanTiltPreComp. Current configurable range: 0 to 300. |
| T/F tnPowerMgmtPortSRSTiltMaintenanceMode | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.14 | TruthValue | read-create | A line parameter that sets SCOT into a maintenance mode where the auto adjustment triggers are not sent, and the receiving lines do not respond to auto triggers. |
| INT tnPowerMgmtPortDegreeFunction | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.15 | INTEGER | read-create | Used to store the function of the degree. Not used by power management system. |
| U32 tnPowerMgmtPortMaxChannels | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.16 | Unsigned32 | read-create | Current configurable range: 4 to 88. |
| T/F tnPowerMgmtPortEgressAdjustForDownstreamEnabled | 1.3.6.1.4.1.7483.2.1.6.2.1.7.1.17 | TruthValue | read-create | Current defaults: Iroadm Cards: 1 Other Cards: 2. |
| tnPowerMgmtPowerOffsetInTable | 1.3.6.1.4.1.7483.2.1.6.2.1.9 | not-accessible | ||
| tnPowerMgmtPowerOffsetInEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.9.1 | not-accessible | ||
| ALU tnPowerMgmtBitRate | 1.3.6.1.4.1.7483.2.1.6.2.1.9.1.1 | AluWdmOtuBitRate | not-accessible | OTU Bit-Rate. Configurable range: 1 to 10000. |
| ALU tnPowerMgmtEncoding | 1.3.6.1.4.1.7483.2.1.6.2.1.9.1.2 | AluWdmOtuEncoding | not-accessible | Signal modulation format. Configurable range: 1 to 10000. |
| I32 tnPowerMgmtOffsetInPowerOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.9.1.3 | Integer32 | read-create | Optical power offset from nominal power level. Current configurable range: -300 to 300. |
| tnPowerMgmtPowerOffsetOutTable | 1.3.6.1.4.1.7483.2.1.6.2.1.10 | not-accessible | ||
| tnPowerMgmtPowerOffsetOutEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.10.1 | not-accessible | ||
| I32 tnPowerMgmtOffsetOutPowerOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.10.1.1 | Integer32 | read-create | Optical power offset from nominal power level. Current configurable range: -300 to 300. |
| tnPowerMgmtIngressPerChannelTable | 1.3.6.1.4.1.7483.2.1.6.2.1.11 | not-accessible | The attributes in this table must not be set together with the same index in the same set request PDU. | |
| tnPowerMgmtIngressPerChannelEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.11.1 | not-accessible | ||
| I32 tnPowerMgmtIngressPerChannelSystemTargetOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.11.1.1 | Integer32 | read-create | The SCOT system derived target power offset relative to common target power. Current configurable range: -300 to 300. |
| I32 tnPowerMgmtIngressPerChannelUserTargetOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.11.1.2 | Integer32 | read-create | The user configured target power offset relative to common target power. -9900 means not configured by user. Current configurable range: -9900, -300 to 300. |
| I32 tnPowerMgmtIngressPerChannelInUseTargetOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.11.1.3 | Integer32 | read-create | The target power offset relative to common target power currently in use. Current configurable range: -300 to 300. |
| I32 tnPowerMgmtIngressPerChannelTargetAbsolute | 1.3.6.1.4.1.7483.2.1.6.2.1.11.1.4 | Integer32 | read-only | The SCOT target power in absolute power. Current range: -9900 to 1100. |
| INT tnPowerMgmtIngressPerChannelApplicability | 1.3.6.1.4.1.7483.2.1.6.2.1.11.1.5 | INTEGER | read-only | Values include: notApplicable - No Och XCo configured for this ITU applicable - Och XCo configured for this ITU. |
| tnPowerMgmtEgressPerChannelTable | 1.3.6.1.4.1.7483.2.1.6.2.1.12 | not-accessible | The attributes in this table must not be set together with the same index in the same set request PDU. | |
| tnPowerMgmtEgressPerChannelEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.12.1 | not-accessible | ||
| I32 tnPowerMgmtEgressPerChannelSystemTargetOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.12.1.1 | Integer32 | read-create | The SCOT system derived target power offset relative to common target power. Current configurable range: -300 to 300. |
| I32 tnPowerMgmtEgressPerChannelUserTargetOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.12.1.2 | Integer32 | read-create | The user configured target power offset relative to common target power. -9900 means not configured by user. Current configurable range: -9900, -300 to 300. |
| I32 tnPowerMgmtEgressPerChannelInUseTargetOffset | 1.3.6.1.4.1.7483.2.1.6.2.1.12.1.3 | Integer32 | read-create | The target power offset relative to common target power currently in use. Current configurable range: -300 to 300. |
| I32 tnPowerMgmtEgressPerChannelTargetAbsolute | 1.3.6.1.4.1.7483.2.1.6.2.1.12.1.4 | Integer32 | read-only | The SCOT target power in absolute power. -9900 means not configured by user. Current range: -9900, -2300 to 1100. |
| INT tnPowerMgmtEgressPerChannelApplicability | 1.3.6.1.4.1.7483.2.1.6.2.1.12.1.5 | INTEGER | read-only | Values include: notApplicable - No Och XCo configured for this ITU applicable - Och XCo configured for this ITU. |
| tnPowerMgmtTechnologyTypesTable | 1.3.6.1.4.1.7483.2.1.6.2.1.13 | not-accessible | ||
| tnPowerMgmtTechnologyTypesEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1 | not-accessible | ||
| STR tnPowerMgmtTechnologyTypesBitRateText | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1.1 | SnmpAdminString | read-create | Text description of BitRate. |
| STR tnPowerMgmtTechnologyTypesEncodingText | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1.2 | SnmpAdminString | read-create | Text description of Encoding. |
| I32 tnPowerMgmtTechnologyTypesWtocmCalib | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1.3 | Integer32 | read-create | Optical power correction in mB from nominal power level for wtocm. Current configurable range: -500 to 500. |
| ROW tnPowerMgmtTechnologyTypesRowStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1.4 | RowStatus | read-create | Row Status of power offset ingress entry. Supported values are: 1 - active 4 - createAndGo 6 - destroy. |
| I32 tnPowerMgmtTechnologyTypesOsnrCalib | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1.5 | Integer32 | read-create | OSNR correction in mB for different optical technology types. Current configurable range: -500 to 500. |
| I32 tnPowerMgmtTechnologyTypesWtocmaCalib | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1.6 | Integer32 | read-create | Optical power correction in mB from nominal power level for WTOCMA. Current configurable range: -500 to 500. |
| I32 tnPowerMgmtTechnologyTypesWtocmfCalib | 1.3.6.1.4.1.7483.2.1.6.2.1.13.1.7 | Integer32 | read-create | Optical power correction in mB from nominal power level for WTOCMF. Current configurable range: -500 to 500. |
| tnPowerMgmtAnyAddTable | 1.3.6.1.4.1.7483.2.1.6.2.1.14 | not-accessible | This table provides access to add adjustment for A/D Block. The attributes in this table must not be set together with the same index 16 in the same set request PDU. | |
| tnPowerMgmtAnyAddEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1 | not-accessible | ||
| TNC tnPowerMgmtAnyAddAdjustPowerGain | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1.1 | TnCommand | read-create | Run the Anydirection Add block adjustment. |
| TRO tnPowerMgmtAnyAddAdjustPowerGainLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1.2 | TropicPowerMgmtResult | read-only | The result of the last executed Anydirection add block operation. |
| TRO tnPowerMgmtAnyAddAdjustPowerGainStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1.3 | TropicPowerMgmtStatus | read-only | This attribute indicates the status of the executed Anydirection Add block operation. |
| T/F tnPowerMgmtAnyAddCommissioned | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1.4 | TruthValue | read-only | Indicates state of adjustment point. true = Adjusted successfully. false = NE event has caused the previous adjustment to be invalidated. |
| T/F tnPowerMgmtAnyAddPassed | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1.5 | TruthValue | read-only | Indicates the Anydirection Add block operation failed or passed. |
| NUM tnPowerMgmtAnyAddAmpIfIndex | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1.6 | InterfaceIndex | read-only | Interface index of the LD in the add position of Anydirecton A/D block. |
| TNC tnPowerMgmtAnyAddAdjustPowerGainAbort | 1.3.6.1.4.1.7483.2.1.6.2.1.14.1.7 | TnCommand | read-create | This attribute allows the network operator to submit an abort on the currently executing power optimization for the Anydirection Add adjustment. |
| tnPowerMgmtAnyDropTable | 1.3.6.1.4.1.7483.2.1.6.2.1.15 | not-accessible | The attributes in this table must not be set together with the same index in the same set request PDU. | |
| tnPowerMgmtAnyDropEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.15.1 | not-accessible | ||
| TNC tnPowerMgmtAnyDropAdjustPowerGain | 1.3.6.1.4.1.7483.2.1.6.2.1.15.1.1 | TnCommand | read-create | Run the Anydirection Drop block adjustment. |
| TRO tnPowerMgmtAnyDropAdjustPowerGainLastResult | 1.3.6.1.4.1.7483.2.1.6.2.1.15.1.2 | TropicPowerMgmtResult | read-only | The result of the last executed Anydirection Drop block operation. |
| TRO tnPowerMgmtAnyDropAdjustPowerGainStatus | 1.3.6.1.4.1.7483.2.1.6.2.1.15.1.3 | TropicPowerMgmtStatus | read-only | This attribute indicates the status of the executed Anydirection Drop block operation. |
| T/F tnPowerMgmtAnyDropCommissioned | 1.3.6.1.4.1.7483.2.1.6.2.1.15.1.4 | TruthValue | read-only | Indicates state of adjustment point. true = Adjusted successfully. false = NE event has caused the previous adjustment to be invalidated. |
| T/F tnPowerMgmtAnyDropPassed | 1.3.6.1.4.1.7483.2.1.6.2.1.15.1.5 | TruthValue | read-only | Indicates the anydirection Drop block operation failed or passed. |
| NUM tnPowerMgmtAnyDropAmpIfIndex | 1.3.6.1.4.1.7483.2.1.6.2.1.15.1.6 | InterfaceIndex | read-only | Interface index of the LD in the drop position of Anydirection A/D block. |
| I32 tnPowerMgmtIroadmAttributeTotal | 1.3.6.1.4.1.7483.2.1.6.2.1.16 | Integer32 | read-only | Total number of attributes in tnPowerMgmtIroadmTable. |
| tnPowerMgmtIroadmTable | 1.3.6.1.4.1.7483.2.1.6.2.1.17 | not-accessible | ||
| tnPowerMgmtIroadmEntry | 1.3.6.1.4.1.7483.2.1.6.2.1.17.1 | not-accessible | ||
| I32 tnPowerMgmtIroadmEgressOAMaxPpcOutFromInputs | 1.3.6.1.4.1.7483.2.1.6.2.1.17.1.1 | Integer32 | read-only | Current Range: -1000 to 1000. Current defaults: IROADMF = -150 IROADMV = 50. |
| I32 tnPowerMgmtIroadmEgressOAPpcOut | 1.3.6.1.4.1.7483.2.1.6.2.1.17.1.2 | Integer32 | read-only | Current Range: -1000 to 1000. Current defaults: IROADMF = -150 IROADMV = 50. |
RFC description
Manages power levels and gain control for optical transport equipment in Nokia TROPIC systems.
Start monitoring Nokia optical transport chassis with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.