TN-ETHSOAM-MIB

All MIBs › TN-ETHSOAM-MIB

Organization: Transition Networks, Inc.

Last Updated: 2014-05-06

Category: Ethernet OAM, Transition Networks Media Converters

Description: Manages Transition Networks Ethernet service OAM maintenance domains and end-point status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TN-ETHSOAM-MIB?

This MIB module is a Transition Networks (TN) implementation of Ethernet Service OAM (based on ITU-T Y.1731 / IEEE 802.1ag concepts) for carrier Ethernet switches and media converters. It exposes data about maintenance domains, maintenance association end points (MEPs), OAM instance configuration, and continuity-check/alarm status. It is used in monitoring the operational health of Ethernet service connections by tracking MEP status, alarm indications, and per-instance direction/level/mode settings, effectively surfacing connectivity-fault and loss-of-continuity conditions rather than classic CPU/memory metrics. It depends conceptually on the ITU-T Y.1731 and IEEE 802.1ag Ethernet OAM standards that define the maintenance-domain/MEP model it implements in SNMP form. It is typically deployed on Transition Networks managed Ethernet switches and media converters used in carrier and industrial Ethernet networks, where TN-ETHSOAM-MIB SNMP monitoring provides the service-level OAM visibility required to catch connectivity-fault conditions.

IPNetwork Monitor allows you to monitor SNMP objects defined in TN-ETHSOAM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Transition Networks managed Ethernet switches
carrier/industrial Ethernet media converters

Monitoring Examples

An administrator would poll the tnEthSoamMPTable (tnEthSoamMPEntry rows) to see each configured maintenance point's tnEthSoamDomaintype, tnEthSoamlevel, tnEthSoamdirection, and tnEthSoamresidencePort. A rising tnEthSoamAlarm or a tnEthSoamStatus change on a given MEP instance indicates a continuity-check failure or misconfigured maintenance level between endpoints. Correlating tnEthSoamFlowInstance and tnEthSoamTaggedVID with the alarm state helps isolate which VLAN/service flow lost end-to-end connectivity.

What Can Be Monitored

MEP/maintenance point status
OAM domain type and level
continuity-check alarms
MEP direction and residence port
tagged VLAN/service flow association

Imported Objects

From IEEE8021-CFM-MIB

dot1agCfmLtrEntry	OBJECT-TYPE
dot1agCfmMepEntry	OBJECT-TYPE
dot1agCfmMepIdentifier	OBJECT-TYPE

From IEEE8021-TC-MIB

IEEE8021PriorityValue

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From Q-BRIDGE-MIB

VlanId
VlanIdOrNone

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

From TRANSITION-SMI

tnProducts

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using tnEthSoamLossStateTxCount OID:

Select a Transition Networks managed Ethernet switch or carrier/industrial media converter (Y.1731/802.1ag MEP/alarm status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tnEthSoamLossStateTxCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The accumulated Tx frame loss count. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
tnEthSoamAisCfgEntry	1.3.6.1.4.1.868.2.5.105.1.12.1.1		not-accessible	This entry represents configuration about the SOAM that provide OAM services.
tnEthSoamAisCfgMgmt	1.3.6.1.4.1.868.2.5.105.1.12
T/F tnEthSoamAisCfgProtection	1.3.6.1.4.1.868.2.5.105.1.12.1.1.1	TruthValue	read-write	Selecting this means that the first 3 AIS PDU is transmitted as fast as possible - in case of using this for protection in the end point.
tnEthSoamAisCfgTable	1.3.6.1.4.1.868.2.5.105.1.12.1		not-accessible	This table provides configuration about ais that provide OAM services.
T/F tnEthSoamAlarm	1.3.6.1.4.1.868.2.5.105.1.1.1.1.9	TruthValue	read-only	An active alarm on the MEP.
INT tnEthSoamAPSCfgCast	1.3.6.1.4.1.868.2.5.105.1.4.1.1.3	INTEGER	read-create	Selection of APS PDU transmitted unicast or multi-cast. The unicast MAC will be taken from the 'Unicast Peer MAC' configuration. Unicast is only valid for L-APS - see 'Type'. The R-APS PDU is always transmitted with multi-cast MAC described in G.8032.
T/F tnEthSoamAPSCfgEnable	1.3.6.1.4.1.868.2.5.105.1.4.1.1.1	TruthValue	read-create	Automatic Protection Switching protocol information transportation based on transmitting/receiving R-APS/L-APS PDU can be enabled/disabled. Must be enabled to support ERPS/ELPS implementing APS. This is only valid with one Peer MEP configured.
tnEthSoamAPSCfgEntry	1.3.6.1.4.1.868.2.5.105.1.4.1.1		not-accessible	This entry represents configuration about the SOAM that provide OAM services.
U32 tnEthSoamAPSCfgLastOctet	1.3.6.1.4.1.868.2.5.105.1.4.1.1.5	Unsigned32	read-create	This is the last octet of the transmitted and expected RAPS multi-cast MAC. In G.8031 (03/2010) a RAPS multi-cast MAC is defined as 01-19-A7-00-00-XX. In current standard the value for this last octet is '01' and the usage of other values is for further study.
tnEthSoamAPSCfgMgmt	1.3.6.1.4.1.868.2.5.105.1.4
IEE tnEthSoamAPSCfgPriority	1.3.6.1.4.1.868.2.5.105.1.4.1.1.2	IEEE8021PriorityValue	read-create	The priority to be inserted as PCP bits in TAG (if any).
tnEthSoamAPSCfgTable	1.3.6.1.4.1.868.2.5.105.1.4.1		not-accessible	This table provides configuration about the APSCfg that provide OAM services.
INT tnEthSoamAPSCfgType	1.3.6.1.4.1.868.2.5.105.1.4.1.1.4	INTEGER	read-create	R-APS: APS PDU is transmitted as R-APS - this is for ERPS. L-APS: APS PDU is transmitted as L-APS - this is for ELPS.
INT tnEthSoamCcmInterval	1.3.6.1.4.1.868.2.5.105.1.6.1.1.5	INTEGER	read-write	Interval between CCM transmissions to be used by all MEPs in the MA.
TNE tnEthSoamClientCfgDomain	1.3.6.1.4.1.868.2.5.105.1.5.1.1.1	TnEthSoamType	read-create	The domain of the client layer. Must be EVC.
tnEthSoamClientCfgEntry	1.3.6.1.4.1.868.2.5.105.1.5.1.1		not-accessible	This entry represents configuration about the Client Configuration that provide OAM services.
U32 tnEthSoamClientCfgFlow1	1.3.6.1.4.1.868.2.5.105.1.5.1.1.3	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow10	1.3.6.1.4.1.868.2.5.105.1.5.1.1.12	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow2	1.3.6.1.4.1.868.2.5.105.1.5.1.1.4	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow3	1.3.6.1.4.1.868.2.5.105.1.5.1.1.5	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow4	1.3.6.1.4.1.868.2.5.105.1.5.1.1.6	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow5	1.3.6.1.4.1.868.2.5.105.1.5.1.1.7	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow6	1.3.6.1.4.1.868.2.5.105.1.5.1.1.8	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow7	1.3.6.1.4.1.868.2.5.105.1.5.1.1.9	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow8	1.3.6.1.4.1.868.2.5.105.1.5.1.1.10	Unsigned32	read-create	Client layer flow instance numbers.
U32 tnEthSoamClientCfgFlow9	1.3.6.1.4.1.868.2.5.105.1.5.1.1.11	Unsigned32	read-create	Client layer flow instance numbers.
DOT tnEthSoamClientCfgLevel	1.3.6.1.4.1.868.2.5.105.1.5.1.1.2	Dot1agCfmMDLevel	read-write	Client layer level - meaning that PDU transmitted in client layer flows will be on this level.
tnEthSoamClientCfgMgmt	1.3.6.1.4.1.868.2.5.105.1.5
tnEthSoamClientCfgTable	1.3.6.1.4.1.868.2.5.105.1.5.1		not-accessible	This table provides configuration about the Link Trace reply that provide OAM services.
DOT tnEthSoamdirection	1.3.6.1.4.1.868.2.5.105.1.1.1.1.4	Dot1agCfmMpDirection	read-create	Direction in which the MP faces on the Bridge Port.
INT tnEthSoamDmCfgCalc	1.3.6.1.4.1.868.2.5.105.1.13.1.1.7	INTEGER	read-create	This is only used if the 'Way' is configured to Two-way. Round trip: The frame dealy calculated by the transmitting and receiving timestamps of initiators. Frame Delay = RxTimeb-TxTimeStampf Flow: The frame dealy calculated by the transmitting and receiving timestamps of initiators and remotes. Frame Delay = (RxTimeb-TxTimeStampf)-(TxTimeStampb-RxTimeStampf).
INT tnEthSoamDmCfgCast	1.3.6.1.4.1.868.2.5.105.1.13.1.1.3	INTEGER	read-create	Selection of 1DM/DMM PDU transmitted unicast or multicast. The unicast MAC will be configured through 'Peer MEP'.
INT tnEthSoamDmCfgCOAction	1.3.6.1.4.1.868.2.5.105.1.13.1.1.12	INTEGER	read-create	The action to counter when overflow happens.
INT tnEthSoamDmCfgCount	1.3.6.1.4.1.868.2.5.105.1.13.1.1.9	INTEGER	read-create	The number of last records to calculate. The range is 10 to 2000.
T/F tnEthSoamDmCfgD2forD1	1.3.6.1.4.1.868.2.5.105.1.13.1.1.11	TruthValue	read-create	Enable to use DMM/DMR packet to calculate one-way DM. If the option is enabled, the following action will be taken. When DMR is received, two-way delay (roundtrip or flow) and both near-end-to-far-end and far-end-to-near-end one-way delay are calcualted. When DMM or 1DM is received, only far-end-to-near-end one-way delay is calculated.
T/F tnEthSoamDmCfgEnable	1.3.6.1.4.1.868.2.5.105.1.13.1.1.1	TruthValue	read-create	Delay Measurement based on transmitting 1DM/DMM PDU can be enabled/disabled. Delay Measurement based on receiving and handling 1DM/DMR PDU is always enabled.
tnEthSoamDmCfgEntry	1.3.6.1.4.1.868.2.5.105.1.13.1.1		not-accessible	This entry represents configuration about the Delay Measurement that provide OAM services.
U32 tnEthSoamDmCfgGap	1.3.6.1.4.1.868.2.5.105.1.13.1.1.8	Unsigned32	read-create	The gap between transmitting 1DM/DMM PDU in 10ms. The range is 10 to 65535.
tnEthSoamDmCfgMgmt	1.3.6.1.4.1.868.2.5.105.1.13
DOT tnEthSoamDmCfgPeerId	1.3.6.1.4.1.868.2.5.105.1.13.1.1.4	Dot1agCfmMepId	read-create	Peer MEP ID.
IEE tnEthSoamDmCfgPriority	1.3.6.1.4.1.868.2.5.105.1.13.1.1.2	IEEE8021PriorityValue	read-create	The priority to be inserted as PCP bits in TAG (if any).
tnEthSoamDmCfgTable	1.3.6.1.4.1.868.2.5.105.1.13.1		not-accessible	This table provides configuration about the Delay Measurement that provide OAM services.
INT tnEthSoamDmCfgTxMode	1.3.6.1.4.1.868.2.5.105.1.13.1.1.6	INTEGER	read-create	Standardize: Y.1731 standardize way to transmit 1DM/DMR. Proprietary: Vitesse proprietary way with follow-up packets to transmit 1DM/DMR.
INT tnEthSoamDmCfgUnit	1.3.6.1.4.1.868.2.5.105.1.13.1.1.10	INTEGER	read-create	The time resolution.
INT tnEthSoamDmCfgWayType	1.3.6.1.4.1.868.2.5.105.1.13.1.1.5	INTEGER	read-create	One-Way: One-Way Delay Measurement implemented on 1DM. Two-Way: Two-Way Delay Measurement implemented on DMM/DMR.
T/F tnEthSoamDmStateAction	1.3.6.1.4.1.868.2.5.105.1.14.1.1.34	TruthValue	read-write	The number of counter overflow - since last 'clear'.
tnEthSoamDmStateEntry	1.3.6.1.4.1.868.2.5.105.1.14.1.1		not-accessible	A entry in the table which generate a configuration for delay measurement state.
G32 tnEthSoamDmStateFNAvgLastN	1.3.6.1.4.1.868.2.5.105.1.14.1.1.6	Gauge32	read-only	The average delay of the last n packets - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateFNAvgTotal	1.3.6.1.4.1.868.2.5.105.1.14.1.1.5	Gauge32	read-only	The average delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateFNAvgVarLastN	1.3.6.1.4.1.868.2.5.105.1.14.1.1.8	Gauge32	read-only	The average delay variation of the last n packets - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateFNAvgVarTotal	1.3.6.1.4.1.868.2.5.105.1.14.1.1.7	Gauge32	read-only	The average delay variation - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateFNMaxValue	1.3.6.1.4.1.868.2.5.105.1.14.1.1.10	Gauge32	read-only	The maximum delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateFNMinValue	1.3.6.1.4.1.868.2.5.105.1.14.1.1.9	Gauge32	read-only	The minimum delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateFNOverFlow	1.3.6.1.4.1.868.2.5.105.1.14.1.1.11	Gauge32	read-only	The number of counter overflow - since last 'clear'.
G32 tnEthSoamDmStateFNRxCount	1.3.6.1.4.1.868.2.5.105.1.14.1.1.3	Gauge32	read-only	The accumulated receive count - since last 'clear'.
G32 tnEthSoamDmStateFNRxError	1.3.6.1.4.1.868.2.5.105.1.14.1.1.4	Gauge32	read-only	The accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout).
G32 tnEthSoamDmStateFNRxTimeout	1.3.6.1.4.1.868.2.5.105.1.14.1.1.2	Gauge32	read-only	The accumulated receive timeout count for two-way only - since last 'clear'.
G32 tnEthSoamDmStateFNTxCount	1.3.6.1.4.1.868.2.5.105.1.14.1.1.1	Gauge32	read-only	The accumulated transmit count - since last 'clear'.
tnEthSoamDmStateMgmt	1.3.6.1.4.1.868.2.5.105.1.14
G32 tnEthSoamDmStateNFAvgLastN	1.3.6.1.4.1.868.2.5.105.1.14.1.1.17	Gauge32	read-only	The average delay of the last n packets - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateNFAvgTotal	1.3.6.1.4.1.868.2.5.105.1.14.1.1.16	Gauge32	read-only	The average delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateNFAvgVarLastN	1.3.6.1.4.1.868.2.5.105.1.14.1.1.19	Gauge32	read-only	The average delay variation of the last n packets - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateNFAvgVarTotal	1.3.6.1.4.1.868.2.5.105.1.14.1.1.18	Gauge32	read-only	The average delay variation - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateNFMaxValue	1.3.6.1.4.1.868.2.5.105.1.14.1.1.21	Gauge32	read-only	The maximum delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateNFMinValue	1.3.6.1.4.1.868.2.5.105.1.14.1.1.20	Gauge32	read-only	The minimum delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateNFOverFlow	1.3.6.1.4.1.868.2.5.105.1.14.1.1.22	Gauge32	read-only	The number of counter overflow - since last 'clear'.
G32 tnEthSoamDmStateNFRxCount	1.3.6.1.4.1.868.2.5.105.1.14.1.1.14	Gauge32	read-only	The accumulated receive count - since last 'clear'.
G32 tnEthSoamDmStateNFRxError	1.3.6.1.4.1.868.2.5.105.1.14.1.1.15	Gauge32	read-only	The accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout).
G32 tnEthSoamDmStateNFRxTimeout	1.3.6.1.4.1.868.2.5.105.1.14.1.1.13	Gauge32	read-only	The accumulated receive timeout count for two-way only - since last 'clear'.
G32 tnEthSoamDmStateNFTxCount	1.3.6.1.4.1.868.2.5.105.1.14.1.1.12	Gauge32	read-only	The accumulated transmit count - since last 'clear'.
tnEthSoamDmStateTable	1.3.6.1.4.1.868.2.5.105.1.14.1		not-accessible	This table has entries which generate a configuration for delay measurement state.
G32 tnEthSoamDmStateTwoWayAvgLastN	1.3.6.1.4.1.868.2.5.105.1.14.1.1.28	Gauge32	read-only	The average delay of the last n packets - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateTwoWayAvgTotal	1.3.6.1.4.1.868.2.5.105.1.14.1.1.27	Gauge32	read-only	The average delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateTwoWayAvgVarLastN	1.3.6.1.4.1.868.2.5.105.1.14.1.1.30	Gauge32	read-only	The average delay variation of the last n packets - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateTwoWayAvgVarTotal	1.3.6.1.4.1.868.2.5.105.1.14.1.1.29	Gauge32	read-only	The average delay variation - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateTwoWayMaxValue	1.3.6.1.4.1.868.2.5.105.1.14.1.1.32	Gauge32	read-only	The maximum delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateTwoWayMinValue	1.3.6.1.4.1.868.2.5.105.1.14.1.1.31	Gauge32	read-only	The minimum delay - since last 'clear'. The unit is microsecond.
G32 tnEthSoamDmStateTwoWayOverFlow	1.3.6.1.4.1.868.2.5.105.1.14.1.1.33	Gauge32	read-only	The number of counter overflow - since last 'clear'.
G32 tnEthSoamDmStateTwoWayRxCount	1.3.6.1.4.1.868.2.5.105.1.14.1.1.25	Gauge32	read-only	The accumulated receive count - since last 'clear'.
G32 tnEthSoamDmStateTwoWayRxError	1.3.6.1.4.1.868.2.5.105.1.14.1.1.26	Gauge32	read-only	The accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout).
G32 tnEthSoamDmStateTwoWayRxTimeout	1.3.6.1.4.1.868.2.5.105.1.14.1.1.24	Gauge32	read-only	The accumulated receive timeout count for two-way only - since last 'clear'.
G32 tnEthSoamDmStateTwoWayTxCount	1.3.6.1.4.1.868.2.5.105.1.14.1.1.23	Gauge32	read-only	The accumulated transmit count - since last 'clear'.
OCT tnEthSoamDomainName	1.3.6.1.4.1.868.2.5.105.1.6.1.1.2	OCTET STRING	read-write	This is either ITU ICC (MEG ID value[1-6]) or IEEE Maintenance Domain Name - depending on 'Format'. See 'Format'.
TNE tnEthSoamDomaintype	1.3.6.1.4.1.868.2.5.105.1.1.1.1.2	TnEthSoamType	read-create	The Domain Mode affects the OAM. The allowed values are Port: This is a MEP in the Port Domain. 'Flow Instance' is a Port. Esp: Future use. Evc: This is a MEP in the EVC Domain. 'Flow Instance' is a EVC. Mpls: Future use. Vlan: This is a MEP in the VLAN Domain. 'Flow Instance' is a VLAN.
INT tnEthSoamEVCPolicyID	1.3.6.1.4.1.868.2.5.105.1.6.1.1.7	INTEGER	read-write	This is relevant for an EVC Egress/Up-MEP. This is the Policy number of the relevant ECE. The Policy ID that the generated TST frames will get as IS1 action. Can be the same as any ECE Policy Number, enabling it to hit the same ACL and thereby the same EVC policer.
INT tnEthSoamEVCQos	1.3.6.1.4.1.868.2.5.105.1.6.1.1.6	INTEGER	read-write	This is only relevant for a EVC MEP. This is the Qos of the EVC used for getting QoS counters for Loss Measurement.
NTF tnEthSoamFaultAlarm	1.3.6.1.4.1.868.2.5.105.0.1			An EthSoam has a persistent defect condition. A notification (fault alarm) is sent to the management entity with the OID of the EthSoam that has detected the fault. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the EthSoam reporting the defect by the indices in the OID of the variables in the notification: tnEthSoamInstance - Also the index of the EthSoam status table entry (tnEthSoamStatusTable).
INT tnEthSoamFlowInstance	1.3.6.1.4.1.868.2.5.105.1.1.1.1.7	INTEGER	read-create	The MEP is related to this flow - See 'Domain'.
INT tnEthSoamFormat	1.3.6.1.4.1.868.2.5.105.1.6.1.1.1	INTEGER	read-write	This is the configuration of the two possible Maintenance Association Identifier formats. ITU ICC: This is defined by ITU. 'ICC' can be max. 6 char. 'MEG id' can be max. 7 char. IEEE String: This is defined by IEEE. 'Domain Name' can be max. 8 char. 'MEG id' can be max. 8 char.
U32 tnEthSoaminstance	1.3.6.1.4.1.868.2.5.105.1.1.1.1.1	Unsigned32	not-accessible	This is the configuration of the two possible Maintenance Association Identifier formats. ITU ICC: This is defined by ITU. 'ICC' can be max. 6 char. 'MEG id' can be max. 7 char. IEEE String: This is defined by IEEE. 'Domain Name' can be max. 8 char. 'MEG id' can be max. 8 char.
DOT tnEthSoamlevel	1.3.6.1.4.1.868.2.5.105.1.1.1.1.6	Dot1agCfmMDLevel	read-create	Level of the Maintenance Point.
tnEthSoamLocalCfgEntry	1.3.6.1.4.1.868.2.5.105.1.6.1.1		not-accessible	A entry in the table represents a configuration for local SOAM.
tnEthSoamLocalCfgMgmt	1.3.6.1.4.1.868.2.5.105.1.6
tnEthSoamLocalCfgTable	1.3.6.1.4.1.868.2.5.105.1.6.1		not-accessible	This table has entries which generate a configuration for local SOAM.
T/F tnEthSoamLossStateAction	1.3.6.1.4.1.868.2.5.105.1.8.1.1.7	TruthValue	read-write	Set of this check and save will clear the accumulated counters and restart ratio calculation.
tnEthSoamLossStateEntry	1.3.6.1.4.1.868.2.5.105.1.8.1.1		not-accessible	A entry in the table represents a configuration for loss measurement State.
G32 tnEthSoamLossStateFELossCount	1.3.6.1.4.1.868.2.5.105.1.8.1.1.4	Gauge32	read-only	The accumulated far end frame loss count - since last 'clear'.
G32 tnEthSoamLossStateFELossRatio	1.3.6.1.4.1.868.2.5.105.1.8.1.1.6	Gauge32	read-only	The far end frame loss ratio calculated based on the far end frame loss count and near end frame transmitted - in the latest 'FLR Interval'. The result is given in percent.
tnEthSoamLossStateMgmt	1.3.6.1.4.1.868.2.5.105.1.8
G32 tnEthSoamLossStateNELossCount	1.3.6.1.4.1.868.2.5.105.1.8.1.1.3	Gauge32	read-only	The accumulated near end frame loss count - since last 'clear'.
G32 tnEthSoamLossStateNELossRatio	1.3.6.1.4.1.868.2.5.105.1.8.1.1.5	Gauge32	read-only	The near end frame loss ratio calculated based on the near end frame loss count and far end frame transmitted - in the latest 'FLR Interval'. The result is given in percent.
G32 tnEthSoamLossStateRxCount	1.3.6.1.4.1.868.2.5.105.1.8.1.1.2	Gauge32	read-only	The accumulated Rx frame loss count.
tnEthSoamLossStateTable	1.3.6.1.4.1.868.2.5.105.1.8.1		not-accessible	This table has entries which generate a configuration for loss measurement State.
G32 tnEthSoamLossStateTxCountEx	1.3.6.1.4.1.868.2.5.105.1.8.1.1.1	Gauge32	read-only	The accumulated Tx frame loss count.
tnEthSoamLtmEntry	1.3.6.1.4.1.868.2.5.105.1.10.1.1		not-accessible	This entry represents configuration about the SOAM that provide OAM services.
tnEthSoamLtmMgmt	1.3.6.1.4.1.868.2.5.105.1.10
IEE tnEthSoamltmPriority	1.3.6.1.4.1.868.2.5.105.1.10.1.1.1	IEEE8021PriorityValue	read-create	The priority to be inserted as PCP bits in TAG (if any).
tnEthSoamLtmTable	1.3.6.1.4.1.868.2.5.105.1.10.1		not-accessible	This table provides configuration about ltm priority that provide OAM services.
INT tnEthSoamLtrDirection	1.3.6.1.4.1.868.2.5.105.1.11.1.1.1	INTEGER	read-only	The priority to be inserted as PCP bits in TAG (if any).
tnEthSoamLtrEntry	1.3.6.1.4.1.868.2.5.105.1.11.1.1		not-accessible	This entry represents configuration about the SOAM that provide OAM services.
tnEthSoamLtrMgmt	1.3.6.1.4.1.868.2.5.105.1.11
tnEthSoamLtrTable	1.3.6.1.4.1.868.2.5.105.1.11.1		not-accessible	This table provides configuration about ltm priority that provide OAM services.
OCT tnEthSoamMegOrMaName	1.3.6.1.4.1.868.2.5.105.1.6.1.1.3	OCTET STRING	read-write	This is either ITU UMC (MEG ID value[7-13]) or IEEE Short MA Name - depending on 'Format'. See 'Format'. In case of ITU ICC format this can be max. 7 char. If only 6 char. is entered the MEG ID value[13] will become NULL.
DOT tnEthSoamMepID	1.3.6.1.4.1.868.2.5.105.1.6.1.1.4	Dot1agCfmMepId	read-write	This value will become the transmitted two byte CCM MEP ID.
tnEthSoamMIB	1.3.6.1.4.1.868.2.5.105			TBD
tnEthSoamMIBConformance	1.3.6.1.4.1.868.2.5.105.2
tnEthSoamMIBNotifications	1.3.6.1.4.1.868.2.5.105.0
tnEthSoamMIBObjects	1.3.6.1.4.1.868.2.5.105.1
INT tnEthSoamMode	1.3.6.1.4.1.868.2.5.105.1.1.1.1.3	INTEGER	read-create	MEP: This is a Maintenance Entity End Point. MIP: This is a Maintenance Entity Intermediate Point.
tnEthSoamMPEntry	1.3.6.1.4.1.868.2.5.105.1.1.1.1		not-accessible	A entry in the table represents a configuration for local SOAM.
tnEthSoamMPMgmt	1.3.6.1.4.1.868.2.5.105.1.1
tnEthSoamMPTable	1.3.6.1.4.1.868.2.5.105.1.1.1		not-accessible	This table provides configuration of SOAM Maintenance Point.
tnEthSoamPeerCfgEntry	1.3.6.1.4.1.868.2.5.105.1.2.1.1		not-accessible	A entry in the table represents a configuration for peer SOAM.
DOT tnEthSoamPeerCfgMepId	1.3.6.1.4.1.868.2.5.105.1.2.1.1.1	Dot1agCfmMepId	not-accessible	The ID of the MEP.
tnEthSoamPeerCfgMgmt	1.3.6.1.4.1.868.2.5.105.1.2
ROW tnEthSoamPeerCfgRowState	1.3.6.1.4.1.868.2.5.105.1.2.1.1.3	RowStatus	read-create	row status.
tnEthSoamPeerCfgTable	1.3.6.1.4.1.868.2.5.105.1.2.1		not-accessible	This table has entries which generate a configuration for peer SOAM.
MAC tnEthSoamPeerCfgUnicastMac	1.3.6.1.4.1.868.2.5.105.1.2.1.1.2	MacAddress	read-write	This MAC will be used when unicast is selected with this peer MEP. Also this MAC is used to create HW checking of receiving CCM PDU (LOC detection) from this MEP.
NTF tnEthSoamPeerFaultAlarm	1.3.6.1.4.1.868.2.5.105.0.2			An EthSoamPeer has a persistent defect condition. A notification (fault alarm) is sent to the management entity with the OID of the EthSoamPeer that has detected the fault. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the EthSoamPeer reporting the defect by the indices in the OID of the variables in the notification: tnEthSoamInstance - Also the index of the EthSoam Peer status table entry (tnEthSoamPeerStatusTable). tnEthSoamPeerStatusMepId - Also the index of the EthSoam Peer status table entry (tnEthSoamPeerStatusTable).
T/F tnEthSoamPeerStatuscLOC	1.3.6.1.4.1.868.2.5.105.1.3.1.1.2	TruthValue	read-only	Fault Cause indicating that no CCM has been received (in 3,5 periods) - from this peer MEP.
T/F tnEthSoamPeerStatuscPeriod	1.3.6.1.4.1.868.2.5.105.1.3.1.1.4	TruthValue	read-only	Fault Cause indicating that a CCM is received with a period different what is configured for this MEP - from this peer MEP.
T/F tnEthSoamPeerStatuscPriority	1.3.6.1.4.1.868.2.5.105.1.3.1.1.5	TruthValue	read-only	Fault Cause indicating that a CCM is received with a priority different what is configured for this MEP - from this peer MEP.
T/F tnEthSoamPeerStatuscRDI	1.3.6.1.4.1.868.2.5.105.1.3.1.1.3	TruthValue	read-only	Fault Cause indicating that a CCM is received with Remote Defect Indication - from this peer MEP.
tnEthSoamPeerStatusEntry	1.3.6.1.4.1.868.2.5.105.1.3.1.1		not-accessible	This entry represents configuration about the SOAM that provide OAM services.
DOT tnEthSoamPeerStatusMepId	1.3.6.1.4.1.868.2.5.105.1.3.1.1.1	Dot1agCfmMepId	not-accessible	MEPID.
tnEthSoamPeerStatusMgmt	1.3.6.1.4.1.868.2.5.105.1.3
tnEthSoamPeerStatusTable	1.3.6.1.4.1.868.2.5.105.1.3.1		not-accessible	This table provides configuration about the SOAM that provide OAM services.
NUM tnEthSoamresidencePort	1.3.6.1.4.1.868.2.5.105.1.1.1.1.5	InterfaceIndex	read-create	This object is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, to which the MEP is attached.
ROW tnEthSoamStatus	1.3.6.1.4.1.868.2.5.105.1.1.1.1.11	RowStatus	read-create	The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
T/F tnEthSoamStatusAIS	1.3.6.1.4.1.868.2.5.105.1.7.1.1.4	TruthValue	read-only	Fault Cause indicating that AIS PDU is received.
T/F tnEthSoamStatusBLK	1.3.6.1.4.1.868.2.5.105.1.7.1.1.7	TruthValue	read-only	The consequent action of blocking service frames in this flow is active.
T/F tnEthSoamStatusCCMLevel	1.3.6.1.4.1.868.2.5.105.1.7.1.1.1	TruthValue	read-only	Fault Cause indicating that a CCM is received with a lower level than the configured for this MEP.
T/F tnEthSoamStatusCCMMeg	1.3.6.1.4.1.868.2.5.105.1.7.1.1.2	TruthValue	read-only	Fault Cause indicating that a CCM is received with a MEG ID different from configured for this MEP.
T/F tnEthSoamStatusCCMMep	1.3.6.1.4.1.868.2.5.105.1.7.1.1.3	TruthValue	read-only	Fault Cause indicating that a CCM is received with a MEP ID different from all 'Peer MEP ID' configured for this MEP.
T/F tnEthSoamStatusCLK	1.3.6.1.4.1.868.2.5.105.1.7.1.1.5	TruthValue	read-only	Fault Cause indicating that LCK PDU is received.
tnEthSoamStatusEntry	1.3.6.1.4.1.868.2.5.105.1.7.1.1		not-accessible	This entry represents configuration about the SOAM that provide OAM services.
tnEthSoamStatusMgmt	1.3.6.1.4.1.868.2.5.105.1.7
T/F tnEthSoamStatusSSF	1.3.6.1.4.1.868.2.5.105.1.7.1.1.6	TruthValue	read-only	Fault Cause indicating that server layer is indicating Signal Fail.
tnEthSoamStatusTable	1.3.6.1.4.1.868.2.5.105.1.7.1		not-accessible	This table provides configuration about the SOAM that provide OAM services.
T/F tnEthSoamStatusTSF	1.3.6.1.4.1.868.2.5.105.1.7.1.1.8	TruthValue	read-only	The consequent action of indicating Trail Signal Fail to-wards protection is active.
VLA tnEthSoamTaggedVID	1.3.6.1.4.1.868.2.5.105.1.1.1.1.8	VlanIdOrNone	read-create	Port MEP: An outer C/S-tag (depending on VLAN Port Type) is added with this VID. Entering '0' means no TAG added.
TNE tnEthSoamTestCfgPattern	1.3.6.1.4.1.868.2.5.105.1.9.1.1.4	TnEthSoamTestPatternType	read-create	This attribute specifies the type of test pattern to be sent or received in an OAM PDU Test TLV.
tnEthSoamTSExtEntry	1.3.6.1.4.1.868.2.5.105.1.9.1.1		not-accessible	A entry in the table represents a configuration for test signal.
tnEthSoamTSExtMgmt	1.3.6.1.4.1.868.2.5.105.1.9
tnEthSoamTSExtTable	1.3.6.1.4.1.868.2.5.105.1.9.1		not-accessible	This table has entries which generate a configuration for test signal.
T/F tnEthSoamTSSeqNum	1.3.6.1.4.1.868.2.5.105.1.9.1.1.1	TruthValue	read-write	sequence number.
T/F tnEthSoamTSStateAction	1.3.6.1.4.1.868.2.5.105.1.9.1.1.3	TruthValue	read-write	This will clear all Test Signal State. Transmission of TST frame will be restarted. Calculation of 'Rx frame count', 'RX rate' and 'Test time' will be started when receiving first TST frame.
INT tnEthSoamTSStateRxRate	1.3.6.1.4.1.868.2.5.105.1.9.1.1.2	INTEGER	read-only	The current received TST frame bit rate in 100 Kbps. This is calculated on a 1 s. basis, starting when first TST frame is received after 'Clear'. The frame size used for this calculation is the first received after 'Clear' .
T/F tnEthSoamVOE	1.3.6.1.4.1.868.2.5.105.1.6.1.1.8	TruthValue	read-write	This will attempt to utilize VOE HW for MEP implementation. Not all platforms support VOE.

RFC description

Manages Ethernet OAM (Operations, Administration, and Maintenance) based on IEEE 802.1ag CFM standards.

Start monitoring Transition Networks managed Ethernet switches, carrier/industrial media converters (Y.1731/802.1ag MEP/alarm status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TN-ETHSOAM-MIB