TIMETRA-PPPOE-MIB

All MIBs › TIMETRA-PPPOE-MIB

Organization: Alcatel-Lucent

Last Updated: 2011-02-01

Description: TIMETRA-PPPOE-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TIMETRA-PPPOE-MIB?

This Nokia/Alcatel-Lucent proprietary MIB manages PPP over Ethernet (PPPoE) provisioning on the 7750 SR SROS platform, the encapsulation commonly used by broadband access providers to tunnel PPP sessions over an Ethernet access network. It exposes PPPoE policy configuration such as PPP MTU, LCP keepalive interval and hold-up multiplier, AC-cookie handling, and PADO delay tuning. Its monitoring value lies in confirming the operational integrity of subscriber-facing PPPoE service: tmnxPppoePlcyRowStatus and tmnxPppoePlcyLastMgmtChange indicate whether a policy is active and when it was last touched, while the keepalive-related objects govern how quickly a dead PPPoE session is detected. As a Nokia SROS extension it works alongside the broader subscriber-management MIB set used on the platform. It's typically deployed on 7750 SR broadband network gateways (BNGs) terminating residential or business PPPoE subscriber sessions. Engineers can download the TIMETRA-PPPOE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-PPPOE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nokia/Alcatel-Lucent 7750 SR broadband network gateway (BNG)

Monitoring Examples

An operator walks tmnxPppoePlcyTable / tmnxPppoePlcyEntry keyed by tmnxPppoePlcyName to check tmnxPppoePlcyRowStatus and confirm a PPPoE policy is active, then examines tmnxPppoePlcyPppMtu and tmnxPppoePlcyLcpKaInterval/tmnxPppoePlcyLcpKaHoldUpMplier to verify keepalive timing matches expectations for detecting dropped subscriber sessions. A change to tmnxPppoePlcyPadoDelay would be checked if subscribers are reporting slow PPPoE session establishment, since this delay directly affects how quickly the access concentrator responds to discovery requests.

What Can Be Monitored

PPPoE policy row status
PPP MTU
LCP keepalive interval and hold-up multiplier
PADO delay
AC-cookie handling

Imported Objects

From IF-MIB

InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddress
InetAddressIPv4
InetAddressPrefixLength
InetAddressType
InetAutonomousSystemNumber

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

From TIMETRA-GLOBAL-MIB

timetraSRMIBModules	OBJECT-IDENTITY
tmnxSRConfs	OBJECT-IDENTITY
tmnxSRNotifyPrefix	OBJECT-IDENTITY
tmnxSRObjs	OBJECT-IDENTITY

From TIMETRA-PPP-MIB

TmnxPppCpState

From TIMETRA-SAP-MIB

sapEncapValue	OBJECT-TYPE
sapPortId	OBJECT-TYPE

From TIMETRA-SERV-MIB

iesIfIndex	OBJECT-TYPE
svcId	OBJECT-TYPE

From TIMETRA-SUBSCRIBER-MGMT-MIB

tmnxSubPppIndex

OBJECT-TYPE

From TIMETRA-TC-MIB

BgpPeeringStatus
TBurstSizeBytesOverride
TCIRRateOverride
TDirection
TItemDescription
TNamedItem
TNamedItemOrEmpty
TPIRRateOverride
TPolicyStatementNameOrEmpty
TQosOverrideType
TmnxAccessLoopEncapDataLink
TmnxAccessLoopEncaps1
TmnxAccessLoopEncaps2
TmnxAncpStringOrZero
TmnxAppProfileStringOrEmpty
TmnxBgpAutonomousSystem
TmnxDhcpOptionType
TmnxManagedRouteStatus
TmnxMlpppEpClass
TmnxPppoePadoDelay
TmnxPppoeSessionId
TmnxPppoeSessionInfoOrigin
TmnxPppoeSessionType
TmnxPppoeUserNameOrEmpty
TmnxServId
TmnxSlaProfileStringOrEmpty
TmnxSubIdentStringOrEmpty
TmnxSubMgtIntDestIdOrEmpty
TmnxSubProfileStringOrEmpty
TmnxVRtrIDOrZero

How to Use in IPNetwork Monitor

Example using tmnxPppoeSapRxPadi OID:

Select a Nokia/Alcatel-Lucent 7750 SR broadband network gateway (PPPoE policy/keepalive status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tmnxPppoeSapRxPadi into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of tmnxPppoeSapRxPadi indicates the number of PADI (PPPoE Active Discovery Initiation) packets received on this SAP. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
timetraPppoeMIBModule	1.3.6.1.4.1.6527.1.1.3.49			This document is the SNMP MIB module to manage and provision the PPP over Ethernet (PPPoE) for the Alcatel-Lucent SROS device. Copyright 2008-2012 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
tmnxPppoeConformance	1.3.6.1.4.1.6527.3.1.1.49
tmnxPppoeCompliances	1.3.6.1.4.1.6527.3.1.1.49.1
tmnxPPPoE77x0V6v0MIBCompliance	1.3.6.1.4.1.6527.3.1.1.49.1.1			The compliance statement for TIMETRA-PPPOE-MIB on Alcatel-Lucent 7750 SR and 7710 series systems release R6.0.
tmnxPPPoE77x0V6v1MIBCompliance	1.3.6.1.4.1.6527.3.1.1.49.1.2			The compliance statement for TIMETRA-PPPOE-MIB on Alcatel-Lucent 7750 SR and 7710 series systems release R6.1.
tmnxPPPoE77x0V7v0MIBCompliance	1.3.6.1.4.1.6527.3.1.1.49.1.3			The compliance statement for TIMETRA-PPPOE-MIB on Alcatel-Lucent 7750 SR and 7710 series systems release R7.0.
tmnxPPPoE77x0V8v0MIBCompliance	1.3.6.1.4.1.6527.3.1.1.49.1.4			The compliance statement for TIMETRA-PPPOE-MIB on Alcatel-Lucent 7750 SR and 7710 series systems release R8.0.
tmnxPPPoE77x0V9v0MIBCompliance	1.3.6.1.4.1.6527.3.1.1.49.1.5			The compliance statement for TIMETRA-PPPOE-MIB on Alcatel-Lucent 7750 SR and 7710 series systems release R9.0.
tmnxPPPoEV10v0MIBCompliance	1.3.6.1.4.1.6527.3.1.1.49.1.6			The compliance statement for TIMETRA-PPPOE-MIB on Alcatel-Lucent SROS release 10.0.
tmnxPppoeGroups	1.3.6.1.4.1.6527.3.1.1.49.2
tmnxPPPoEV6v0Group	1.3.6.1.4.1.6527.3.1.1.49.2.1			The group of objects supporting PPPoE on Alcatel-Lucent SROS series systems 6.0 release.
tmnxPPPoEV6v0NotifyGroup	1.3.6.1.4.1.6527.3.1.1.49.2.2			The group of notifications generated by the PPPoE feature on Alcatel-Lucent SROS series systems 6.0 release.
tmnxPPPoEV6v0NotificationObjGroup	1.3.6.1.4.1.6527.3.1.1.49.2.3			The group of objects supporting management of PPPoE notification objects on Alcatel-Lucent SROS series systems 6.0 release.
tmnxPPPoEV6v0BsxGroup	1.3.6.1.4.1.6527.3.1.1.49.2.4			The group of objects supporting management of PPPoE BSX (Application Assurance) objects on Alcatel-Lucent SROS series systems 6.0 release.
tmnxPPPoEManagedRoutesGroup	1.3.6.1.4.1.6527.3.1.1.49.2.5			The group of objects supporting PPPoE Managed Routes on Alcatel-Lucent SROS series systems.
tmnxPPPoEV6v1Group	1.3.6.1.4.1.6527.3.1.1.49.2.6			The group of objects supporting PPPoE on Alcatel-Lucent SROS series systems 6.1 release.
tmnxPPPoEV7v0Group	1.3.6.1.4.1.6527.3.1.1.49.2.7			The group of objects supporting PPPoE on Alcatel-Lucent SROS series systems 7.0 release.
tmnxPPPoESessionBGPGroup	1.3.6.1.4.1.6527.3.1.1.49.2.8			The group of objects supporting PPPoE BGP peering on Alcatel-Lucent SROS series systems.
tmnxPPPoEObsoleteV7v0Group	1.3.6.1.4.1.6527.3.1.1.49.2.9			The group of objects obsoleted on Alcatel-Lucent SROS series systems.
tmnxPPPoEV8v0Group	1.3.6.1.4.1.6527.3.1.1.49.2.10			The group of objects supporting PPPoE on Alcatel-Lucent SROS series systems 8.0 release.
tmnxPPPoEV8v0NotifyGroup	1.3.6.1.4.1.6527.3.1.1.49.2.11			The group of notifications generated by the PPPoE feature on Alcatel-Lucent SROS series systems 8.0 release.
tmnxPPPoEV8v0NotifyObjsGroup	1.3.6.1.4.1.6527.3.1.1.49.2.12			The group of objects supporting management of PPPoE notification objects on Alcatel-Lucent SROS series systems 8.0 release.
tmnxPPPoEV9v0Group	1.3.6.1.4.1.6527.3.1.1.49.2.15			The group of objects supporting PPPoE added in Alcatel-Lucent SROS series systems 9.0 release.
tmnxPPPV9v0Group	1.3.6.1.4.1.6527.3.1.1.49.2.16			The group of objects supporting PPP added in Alcatel-Lucent SROS series systems 9.0 release.
tmnxPPPoEObsoleteV9v0Group	1.3.6.1.4.1.6527.3.1.1.49.2.17			The group of PPPoE objects obsoleted on Alcatel-Lucent SROS series systems release 9.0.
tmnxPPPMlpppGroup	1.3.6.1.4.1.6527.3.1.1.49.2.20			The group of objects supporting subscriber MLPPP in Alcatel-Lucent SROS series systems.
tmnxPPPRejectDisabledNcp	1.3.6.1.4.1.6527.3.1.1.49.2.21			The group of objects supporting management of PPP Policy reject disabled NCP's options in Alcatel-Lucent SROS series systems.
tmnxPPPoEV10v0NotifyObjsGroup	1.3.6.1.4.1.6527.3.1.1.49.2.22			The group of objects supporting management of PPPoE notification objects on Alcatel-Lucent SROS series systems 10.0 release.
tmnxPPPoEV10v0NotifyGroup	1.3.6.1.4.1.6527.3.1.1.49.2.23			The group of notifications generated by the PPPoE feature on Alcatel-Lucent SROS series systems 10.0 release.
tmnxPppoe	1.3.6.1.4.1.6527.3.1.2.49
tmnxPppoeObjects	1.3.6.1.4.1.6527.3.1.2.49.1
TIM tmnxPppoePlcyTableLastChanged	1.3.6.1.4.1.6527.3.1.2.49.1.1	TimeStamp	read-only	The value of tmnxPppoePlcyTableLastChanged indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxPppoePlcyTable.
tmnxPppoePlcyTable	1.3.6.1.4.1.6527.3.1.2.49.1.2		not-accessible	The tmnxPppoePlcyTable has an entry for each PPP(oE) policy configured in the system. This table can be used to configure PPP for PPPoE (PPP over Ethernet) and PPPoA (PPP over ATM) subscribers.
tmnxPppoePlcyEntry	1.3.6.1.4.1.6527.3.1.2.49.1.2.1		not-accessible	Each row entry represents a PPP(oE) policy configured in the system. Entries can be created and deleted via SNMP SET operations on the object tmnxPppoePlcyRowStatus.
TNA tmnxPppoePlcyName	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.1	TNamedItem	not-accessible	The value of tmnxPppoePlcyName specifies the name of the PPP(oE) policy.
ROW tmnxPppoePlcyRowStatus	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.2	RowStatus	read-create	The value of tmnxPppoePlcyRowStatus controls the creation and deletion of rows in this table.
TIM tmnxPppoePlcyLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.3	TimeStamp	read-only	The value of tmnxPppoePlcyLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TIT tmnxPppoePlcyDescription	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.4	TItemDescription	read-create	The value of tmnxPppoePlcyDescription specifies the user provided description of this PPP policy.
U32 tmnxPppoePlcyPppMtu	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.5	Unsigned32	read-create	The value of tmnxPppoePlcyPppMtu specifies the largest IP packet that can be sent out without being fragmented over the specific PPPoE tunnel. A value of 0 indicates the specific MTU is derived from the interface.
U32 tmnxPppoePlcyLcpKaInterval	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.6	Unsigned32	read-create	The value tmnxPppoePlcyLcpKaInterval specifies the time interval in seconds at which LCP echo requests are transmitted.
U32 tmnxPppoePlcyLcpKaHoldUpMplier	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.7	Unsigned32	read-create	The value of tmnxPppoePlcyLcpKaHoldUpMplier specifies how many LCP keepalive messages can be missed before the related PPP session is brought down.
T/F tmnxPppoePlcyDisableAcCookies	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.8	TruthValue	read-create	The value tmnxPppoePlcyDisableAcCookies specifies whether the use of AC-Cookie tags during the PPPoE discovery phase is disabled.
TMN tmnxPppoePlcyPadoDelay	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.9	TmnxPppoePadoDelay	read-create	The value tmnxPppoePlcyPadoDelay specifies the delay timeout before sending a PADO (PPPoE Active Discovery Offer).
U32 tmnxPppoePlcyMaxSessionsPerMac	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.10	Unsigned32	read-create	The value tmnxPppoePlcyMaxSessionsPerMac specifies the maximum number of PPPoE sessions that can be created per MAC address.
T/F tmnxPppoePlcyReplyOnPadt	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.11	TruthValue	read-create	The value tmnxPppoePlcyReplyOnPadt specifies whether the system replies with a PADT (PPPoE Active Discovery Terminate) packet when a PADT packet is received for an existing PPPoE session.
INT tmnxPppoePlcyPppAuthentication	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.12	INTEGER	read-create	The value tmnxPppoePlcyPppAuthentication specifies what PPP authentication protocol(s) will be negotiated during the LCP phase. This field is only applicable if PAP/CHAP authentication is enabled via configuration of a RADIUS authentication policy or a local user database. If set to 'pap' or 'chap', only PAP respectively CHAP is negotiated. If set to 'prefChap', first CHAP is negotiated followed by PAP. If set to 'prefPap', first PAP is negotiated followed by CHAP.
U32 tmnxPppoePlcyPppMinChapChallenge	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.13	Unsigned32	read-create	The value of tmnxPppoePlcyPppMinChapChallenge specifies the minimum length of the CHAP challenge generated by the system.
U32 tmnxPppoePlcyPppMaxChapChallenge	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.14	Unsigned32	read-create	The value of tmnxPppoePlcyPppMaxChapChallenge specifies the maximum length of the CHAP challenge generated by the system.
U32 tmnxPppoePlcyPppInitialDelay	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.15	Unsigned32	read-create	The value of tmnxPppoePlcyPppInitialDelay specifies the delay before starting the PPP stack of a PPPoE session.
T/F tmnxPppoePlcyPppIpcpSubnetNeg	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.20	TruthValue	read-create	The value tmnxPppoePlcyPppIpcpSubnetNeg specifies if IPCP subnet negotiation is enabled.
STR tmnxPppoePlcyPadoAcName	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.21	DisplayString	read-create	The value tmnxPppoePlcyPadoAcName specifies the AC-name (Access Concentrator's name) tag which will be included in the PADO (PPPoE Active Discovery Offer). If the empty string is specified, the chassis name (TIMETRA-CHASSIS-NAME::tmnxChassisName) will be used as AC-name.
T/F tmnxPppoePlcyPppMtuForceGt1492	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.22	TruthValue	read-create	The value tmnxPppoePlcyPppMtuForceGt1492 specifies for PPPoE sessions whether a PPP MTU greater than 1492 can be negotiated without following the procedure described in RFC 4638.
T/F tmnxPppoePlcyUniqueSessIdsPerSap	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.23	TruthValue	read-create	The value tmnxPppoePlcyUniqueSessIdsPerSap specifies whether each PPPoE session on the same SAP gets a unique session-id.
T/F tmnxPppoePlcyRejectDisabledNcp	1.3.6.1.4.1.6527.3.1.2.49.1.2.1.24	TruthValue	read-create	The value tmnxPppoePlcyRejectDisabledNcp specifies whether disabled NCP's (Network Control Protocol) are rejected or silently ignored. When the value of this object is set to 'true(1)' then disabled NCP's are explicitly rejected.
TIM tmnxPppoePlcyPppOptionTblLstChg	1.3.6.1.4.1.6527.3.1.2.49.1.3	TimeStamp	read-only	The value of tmnxPppoePlcyPppOptionTblLstChg indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxPppoePlcyPppOptionTable.
tmnxPppoePlcyPppOptionTable	1.3.6.1.4.1.6527.3.1.2.49.1.4		not-accessible	The tmnxPppoePlcyPppOptionTable has an entry for each PPP option configured in the system.
tmnxPppoePlcyPppOptionEntry	1.3.6.1.4.1.6527.3.1.2.49.1.4.1		not-accessible	Each row entry represents a PPP option configured in the system. Entries can be created and deleted via SNMP SET operations on the object tmnxPppoePlcyOptionRowStatus.
INT tmnxPppoePlcyOptionProtocol	1.3.6.1.4.1.6527.3.1.2.49.1.4.1.1	INTEGER	not-accessible	The value of tmnxPppoePlcyOptionProtocol specifies the PPP protocol for this option.
U32 tmnxPppoePlcyOptionNumber	1.3.6.1.4.1.6527.3.1.2.49.1.4.1.2	Unsigned32	not-accessible	The value of tmnxPppoePlcyOptionNumber specifies the number of this option.
ROW tmnxPppoePlcyOptionRowStatus	1.3.6.1.4.1.6527.3.1.2.49.1.4.1.3	RowStatus	read-create	The value of tmnxPppoePlcyOptionRowStatus controls the creation and deletion of rows in this table. The objects tmnxPppoePlcyOptionType and tmnxPppoePlcyOptionValue must be set when creating a new row.
TIM tmnxPppoePlcyOptionLstMgmtChange	1.3.6.1.4.1.6527.3.1.2.49.1.4.1.4	TimeStamp	read-only	The value of tmnxPppoePlcyOptionLstMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TMN tmnxPppoePlcyOptionType	1.3.6.1.4.1.6527.3.1.2.49.1.4.1.5	TmnxDhcpOptionType	read-create	The value of tmnxPppoePlcyOptionType specifies how the value of this option in stored in tmnxPppoePlcyOptionValue. This object is mandatory at creation time.
OCT tmnxPppoePlcyOptionValue	1.3.6.1.4.1.6527.3.1.2.49.1.4.1.6	OCTET STRING	read-create	The value of tmnxPppoePlcyOptionValue specifies the value of this option. This object is mandatory at creation time. A zero length value is only allowed when the value of tmnxPppoePlcyOptionType is 'hex'.
TIM tmnxPppoeIesIfInfoTableLastChg	1.3.6.1.4.1.6527.3.1.2.49.1.5	TimeStamp	read-only	The value of tmnxPppoeIesIfInfoTableLastChg indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxPppoeIesIfInfoTable.
tmnxPppoeIesIfInfoTable	1.3.6.1.4.1.6527.3.1.2.49.1.6		not-accessible	A table that contains IES interface PPPoE configuration information. A row is automatically created in the tmnxPppoeIesIfInfoTable for an entry in the iesIfTable where either the value of the object iesIfType - is equal to 'group (3)' and the value of iesIfGroupInterfaceType is equal to 'plain', or - equal to 'subscriber (2)' while the value of the objects iesIfFwdServId and iesIfFwdSubIf are not equal to zero. The first case is referred to as 'group interface' and the second as 'retailer interface'.
tmnxPppoeIesIfInfoEntry	1.3.6.1.4.1.6527.3.1.2.49.1.6.1		not-accessible	PPPoE specific information about an IES interface.
TIM tmnxPppoeIesIfLastChg	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.1	TimeStamp	read-only	The value of tmnxPppoeIesIfLastChg indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TIT tmnxPppoeIesIfDescription	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.2	TItemDescription	read-write	The value of the object tmnxPppoeIesIfDescription specifies a user provided description for PPPoE on this IES interface. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.
TMN tmnxPppoeIesIfAdminState	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.3	TmnxPppoeAdminStatus	read-write	The value of the object tmnxPppoeIesIfAdminState specifies the administrative state of PPPoE on this IES interface. The default value of this object is equal to 'disabled', except for a retailer interface, where it is equal to 'enabled'. In case of a retailer interface, setting the value of this object (to 'disabled') is not allowed.
TNA tmnxPppoeIesIfPolicy	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.4	TNamedItem	read-write	The value of tmnxPppoeIesIfPolicy specifies the PPPoE policy applicable on this IES interface. The corresponding policy is defined in tmnxPppoePlcyTable. In case of a retailer interface, the value of this object is irrelevant and setting it (to a value other than default) is not allowed.
U32 tmnxPppoeIesIfSessionLimit	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.5	Unsigned32	read-write	The value of tmnxPppoeIesIfSessionLimit specifies the maximum number of PPPoE sessions allowed on this IES interface.
U32 tmnxPppoeIesIfSapSessionLimit	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.6	Unsigned32	read-write	The value of tmnxPppoeIesIfSapSessionLimit specifies the maximum number of PPPoE sessions allowed on each SAP belonging to this IES interface. In case of a retailer interface, the value of this object is irrelevant, and setting it (to a value other than 1) is not allowed.
TNA tmnxPppoeIesIfPapChapUserDb	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.7	TNamedItemOrEmpty	read-write	The value of tmnxPppoeIesIfPapChapUserDb specifies the local user database to use for PPP PAP/CHAP authentication. If no PPP authentication is required, the value of this object must be set to the empty string.
TNA tmnxPppoeIesIfUserDb	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.8	TNamedItemOrEmpty	read-write	The value of tmnxPppoeIesIfUserDb specifies the local user database to use for PPPoE PADI or PPP PAP/CHAP based authentication. If no authentication with the local user database is required, the value of this object must be set to the empty string. In case of a retailer interface, setting the value of this object (to a value other than the empty string) is not allowed.
T/F tmnxPppoeIesIfDhcpcCcagOriginSap	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.9	TruthValue	read-write	In case this interface is connected to a VPLS via a CCA (Cross Connect Adaptor) MDA, the value of tmnxPppoeIesIfDhcpcCcagOriginSap specifies whether the system includes the original VPLS SAP in the circuit-id option to send to the DHCP server(s). In case of a retailer interface, the value of this object is irrelevant, and setting it (to a value other than false) is not allowed.
INT tmnxPppoeIesIfAntiSpoofing	1.3.6.1.4.1.6527.3.1.2.49.1.6.1.10	INTEGER	read-write	The value of tmnxPppoeIesIfAntiSpoofing specifies the type of PPPoE anti-spoof filtering to use.
tmnxPppoeSapStatsTable	1.3.6.1.4.1.6527.3.1.2.49.1.7		not-accessible	A table that contains statistics on PPPoE per SAP.
tmnxPppoeSapStatsEntry	1.3.6.1.4.1.6527.3.1.2.49.1.7.1		not-accessible	PPPoE statistics about a SAP.
C32 tmnxPppoeSapRxPadiEx	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.1	Counter32	read-only	The value of tmnxPppoeSapRxPadi indicates the number of PADI (PPPoE Active Discovery Initiation) packets received on this SAP.
C32 tmnxPppoeSapRxPadr	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.2	Counter32	read-only	The value of tmnxPppoeSapRxPadr indicates the number of PADR (PPPoE Active Discovery Request) packets received on this SAP.
C32 tmnxPppoeSapRxPadt	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.3	Counter32	read-only	The value of tmnxPppoeSapRxPadt indicates the number of PADT (PPPoE Active Discovery Terminate) packets received on this SAP.
C32 tmnxPppoeSapRxSession	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.4	Counter32	read-only	The value of tmnxPppoeSapRxSession indicates the number packets received during the PPP session stage on this SAP.
C32 tmnxPppoeSapRxInvalidVersion	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.5	Counter32	read-only	The value of tmnxPppoeSapRxInvalidVersion indicates the number of PPPoE packets received with an invalid version field.
C32 tmnxPppoeSapRxInvalidType	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.6	Counter32	read-only	The value of tmnxPppoeSapRxInvalidType indicates the number of PPPoE packets received with an invalid type field.
C32 tmnxPppoeSapRxInvalidCode	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.7	Counter32	read-only	The value of tmnxPppoeSapRxInvalidCode indicates the number of PPPoE packets received with an invalid code field.
C32 tmnxPppoeSapRxInvalidSession	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.8	Counter32	read-only	The value of tmnxPppoeSapRxInvalidSession indicates the number of PPPoE packets received with an invalid session-id field.
C32 tmnxPppoeSapRxInvalidLen	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.9	Counter32	read-only	The value of tmnxPppoeSapRxInvalidLen indicates the number of PPPoE packets received with an invalid length field.
C32 tmnxPppoeSapRxInvalidTags	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.10	Counter32	read-only	The value of tmnxPppoeSapRxInvalidTags indicates the number of PPPoE Active Discovery packets received with invalid tags.
C32 tmnxPppoeSapRxInvalidAcCookie	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.11	Counter32	read-only	The value of tmnxPppoeSapRxInvalidAcCookie indicates the number of PPPoE Active Discovery packets received with an invalid AC-Cookie tag.
C32 tmnxPppoeSapRxDropped	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.12	Counter32	read-only	The value of tmnxPppoeSapRxDropped indicates the number of dropped PPPoE packets.
C32 tmnxPppoeSapTxPado	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.13	Counter32	read-only	The value of tmnxPppoeSapTxPado indicates the number of PADO (PPPoE Active Discovery Offer) packets transmitted on this SAP.
C32 tmnxPppoeSapTxPads	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.14	Counter32	read-only	The value of tmnxPppoeSapTxPads indicates the number of PADS (PPPoE Active Discovery Session) packets transmitted on this SAP.
C32 tmnxPppoeSapTxPadt	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.15	Counter32	read-only	The value of tmnxPppoeSapTxPadt indicates the number of PADT (PPPoE Active Discovery Terminate) packets transmitted on this SAP.
C32 tmnxPppoeSapTxSession	1.3.6.1.4.1.6527.3.1.2.49.1.7.1.16	Counter32	read-only	The value of tmnxPppoeSapTxSession indicates the number packets transmitted during the PPP session stage on this SAP.
tmnxPppoeSessionTable	1.3.6.1.4.1.6527.3.1.2.49.1.8		not-accessible	A table that contains PPPoE sessions.
tmnxPppoeSessionEntry	1.3.6.1.4.1.6527.3.1.2.49.1.8.1		not-accessible	Information about a specific PPPoE session. In release 9.0 and higher, the actual information is in the SUBSCRIBER-MGMT-MIB::tmnxSubPppTable. The corresponding row in that table can be directly retrieved using the value of the object tmnxPppoeSessionSubPppIndex.
MAC tmnxPppoeSessionMac	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.1	MacAddress	not-accessible	The value of tmnxPppoeSessionMac indicates the MAC address of the PPPoE session.
TMN tmnxPppoeSessionId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.2	TmnxPppoeSessionId	not-accessible	The value of tmnxPppoeSessionId indicates the session id of the PPPoE session.
TIK tmnxPppoeSessionUpTime	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.3	TimeTicks	read-only	The value of tmnxPppoeSessionUpTime indicates how long (in hundredths of a second) that the session already exists in this table.
TMN tmnxPppoeSessionLcpState	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.4	TmnxPppCpState	read-only	The value of tmnxPppoeSessionLcpState indicates the obsolete state of the PPP Link Control Protocol of the PPPoE session.
TMN tmnxPppoeSessionIpcpState	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.5	TmnxPppCpState	read-only	The value of tmnxPppoeSessionIpcpState indicates the obsolete state of the PPP IP Control Protocol of the PPPoE session.
U32 tmnxPppoeSessionPppMtu	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.6	Unsigned32	read-only	The value of tmnxPppoeSessionPppMtu indicates the PPP MTU of the PPPoE session.
INT tmnxPppoeSessionPppAuthProtocol	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.7	INTEGER	read-only	The value of tmnxPppoeSessionPppAuthProtocol indicates the PPP protocol used to authenticate the PPPoE session. The value 'none' indicates that no PPP authentication was done. The value 'pap' indicates that authentication was done via the Password Authentication Protocol. The value 'chap' indicates that authentication was done via the Challenge-Handshake Authentication Protocol.
TMN tmnxPppoeSessionPppUserName	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.8	TmnxPppoeUserNameOrEmpty	read-only	The value of tmnxPppoeSessionPppUserName indicates the user name learned during the PPP authentication phase.
STR tmnxPppoeSessionSubIdent	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.9	TmnxSubIdentStringOrEmpty	read-only	The value of tmnxPppoeSessionSubIdent indicates the subscriber applicable for this PPPoE session. The value of tmnxPppoeSessionOriginSubIdent indicates from what source this subscriber identification was received.
TMN tmnxPppoeSessionOriginSubIdent	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.10	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxPppoeSessionOriginSubIdent indicates which source provided the subscriber.
STR tmnxPppoeSessionSubProfString	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.11	TmnxSubProfileStringOrEmpty	read-only	The value of tmnxPppoeSessionSubProfString indicates the subscriber profile string applicable for this PPPoE session. The value of tmnxPppoeSessionOriginStrings indicates from what source this string was received.
STR tmnxPppoeSessionSlaProfString	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.12	TmnxSlaProfileStringOrEmpty	read-only	The value of tmnxPppoeSessionSlaProfString indicates the SLA profile string applicable for this PPPoE session. The value of tmnxPppoeSessionOriginStrings indicates from what source this string was received.
STR tmnxPppoeSessionAncpString	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.13	TmnxAncpStringOrZero	read-only	The value of tmnxPppoeSessionAncpString indicates the ANCP string applicable for this PPPoE session. The value of tmnxPppoeSessionOriginStrings indicates from what source this string was received.
NUM tmnxPppoeSessionInterDestId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.14	TmnxSubMgtIntDestIdOrEmpty	read-only	The value of tmnxPppoeSessionInterDestId indicates the intermediate destination identifier applicable for this PPPoE session. The value of tmnxPppoeSessionOriginStrings indicates from what source this string was received.
STR tmnxPppoeSessionAppProfString	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.15	TmnxAppProfileStringOrEmpty	read-only	The value of tmnxPppoeSessionAppProfString indicates the application profile string applicable for this PPPoE session. The value of tmnxPppoeSessionOriginStrings indicates from what source this string was received.
TMN tmnxPppoeSessionOriginStrings	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.16	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxPppoeSessionOriginStrings indicates which source provided the subscriber identification strings (subscriber profile string, SLA profile string, ANCP string, intermediate destination identifier and application profile string).
U32 tmnxPppoeSessionSessionTimeout	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.17	Unsigned32	read-only	The value of tmnxPppoeSessionSessionTimeout indicates the session timeout received from the Radius server (if applicable).
IPt tmnxPppoeSessionIpAddrType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.18	InetAddressType	read-only	The value of tmnxPppoeSessionIpAddrType indicates the address type of tmnxPppoeSessionIpAddr.
IP tmnxPppoeSessionIpAddr	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.19	InetAddress	read-only	The value of tmnxPppoeSessionIpAddr indicates the IP address of the PPPoE session. The value of tmnxPppoeSessionOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxPppoeSessionPrimaryDnsType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.20	InetAddressType	read-only	The value of tmnxPppoeSessionPrimaryDnsType indicates the address type of tmnxPppoeSessionPrimaryDns.
IP tmnxPppoeSessionPrimaryDns	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.21	InetAddress	read-only	The value of tmnxPppoeSessionPrimaryDns indicates the primary DNS server. The value of this object is ''H when not applicable. The value of tmnxPppoeSessionOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxPppoeSessionSecondryDnsType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.22	InetAddressType	read-only	The value of tmnxPppoeSessionSecondryDnsType indicates the address type of tmnxPppoeSessionSecondryDns.
IP tmnxPppoeSessionSecondryDns	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.23	InetAddress	read-only	The value of tmnxPppoeSessionSecondryDns indicates the secondary DNS server. The value of this object is ''H when not applicable. The value of tmnxPppoeSessionOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxPppoeSessionPrimaryNbnsType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.24	InetAddressType	read-only	The value of tmnxPppoeSessionPrimaryNbnsType indicates the address type of tmnxPppoeSessionPrimaryNbns.
IP tmnxPppoeSessionPrimaryNbns	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.25	InetAddress	read-only	The value of tmnxPppoeSessionPrimaryNbns indicates the primary NBNS server. The value of this object is ''H when not applicable. The value of tmnxPppoeSessionOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxPppoeSessionSecondryNbnsType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.26	InetAddressType	read-only	The value of tmnxPppoeSessionSecondryNbnsType indicates the address type of tmnxPppoeSessionSecondryNbns.
IP tmnxPppoeSessionSecondryNbns	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.27	InetAddress	read-only	The value of tmnxPppoeSessionSecondryNbns indicates the secondary NBNS server. The value of this object is ''H when not applicable. The value of tmnxPppoeSessionOriginIpcpInfo indicates from what source this IP address was received.
TMN tmnxPppoeSessionOriginIpcpInfo	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.28	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxPppoeSessionOriginIpcpInfo indicates which source provided the IPCP information (IP, DNS and NBNS addresses).
OCT tmnxPppoeSessionCircuitId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.29	OCTET STRING	read-only	The value of tmnxPppoeSessionCircuitId indicates the value of the circuit-id sub-option inserted by the PPPoE intermediate agent.
OCT tmnxPppoeSessionRemoteId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.30	OCTET STRING	read-only	The value of tmnxPppoeSessionRemoteId indicates the value of the remote-id sub-option inserted by the PPPoE intermediate agent.
STR tmnxPppoeSessionAddressPool	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.31	DisplayString	read-only	The value of tmnxPppoeSessionAddressPool indicates the IP address pool which is used to search for an IP address for this session.
TMN tmnxPppoeSessionType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.32	TmnxPppoeSessionType	read-only	The value of tmnxPppoeSessionType indicates the type of this session.
TMN tmnxPppoeSessionRetailerSvcId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.33	TmnxServId	read-only	The value of tmnxPppoeSessionRetailerSvcId indicates the service ID of the retailer VPRN service to which this session belongs. If the value of this object is non-zero, the session belongs to a retailer VPRN.
NUM tmnxPppoeSessionRetailerIf	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.34	InterfaceIndexOrZero	read-only	The value of tmnxPppoeSessionRetailerIf indicates the interface index of the retailer VPRN interface to which this session belongs. If the value of this object is non-zero, the session belongs to a retailer VPRN.
TMN tmnxPppoeSessionL2tpVrtrId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.35	TmnxVRtrIDOrZero	read-only	The value of tmnxPppoeSessionL2tpVrtrId indicates the virtual router ID of the L2TP session associated with this PPPoE session. If there is no L2TP session associated with this PPPoE session, the value of this object is equal to zero.
U32 tmnxPppoeSessionL2tpConnectionId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.36	Unsigned32	read-only	The value of tmnxPppoeSessionL2tpVrtrId indicates the connection ID of the L2TP session associated with this PPPoE session. The values of tmnxPppoeSessionL2tpVrtrId and tmnxPppoeSessionL2tpConnectionId are the index in the table TIMETRA-L2TP-MIB::tmnxL2tpSeStatusTable of the L2TP session associated with this PPPoE session. If there is no L2TP session associated with this PPPoE session, the value of this object is equal to zero.
STR tmnxPppoeSessionServiceName	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.37	DisplayString	read-only	The value of tmnxPppoeSessionServiceName indicates the value of the PPPoE service-name tag received in PADI packets.
TNA tmnxPppoeSessionCategoryMapName	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.38	TNamedItemOrEmpty	read-only	The value of tmnxPppoeSessionCategoryMapName indicates the category map name applicable for this PPPoE session. The value of tmnxPppoeSessionOriginStrings indicates from what source this string was received.
OCT tmnxPppoeSessionRadiusClassAttr	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.39	OCTET STRING	read-only	The value of tmnxPppoeSessionRadiusClassAttr indicates the Class attribute returned by the RADIUS server in an Access-Accept message. If no RADIUS authentication is performed for this session, or RADIUS did not return this attribute, the value of this object is empty.
STR tmnxPppoeSessionRadiusUserName	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.40	DisplayString	read-only	The value of tmnxPppoeSessionRadiusUserName indicates the User-Name attribute returned by the RADIUS server in an Access-Accept message. If RADIUS did not return this attribute, the value of this object is equal to the User-Name attribute sent in the original Access-Request message. If no RADIUS authentication is performed for this session, the value of this object is empty.
TMN tmnxPppoeSessionIpv6cpState	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.41	TmnxPppCpState	read-only	The value of tmnxPppoeSessionIpv6cpState indicates the obsolete state of the PPP IPv6 Control Protocol of the PPPoE session.
OCT tmnxPppoeSessionInterfaceId	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.42	OCTET STRING	read-only	The value of tmnxPppoeSessionInterfaceId indicates the value of the remote-id sub-option inserted by the PPPoE intermediate agent.
TMN tmnxPppoeSessionOriginIpv6cpInfo	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.43	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxPppoeSessionOriginIpv6cpInfo indicates which source provided the IPCP information (IP, DNS and NBNS addresses).
IPt tmnxPppoeSessionIpv6DnsType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.44	InetAddressType	read-only	The value of tmnxPppoeSessionIpv6DnsType indicates the address type of tmnxPppoeSessionIpv6Dns1/2.
IP tmnxPppoeSessionIpv6Dns1	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.45	InetAddress	read-only	The value of tmnxPppoeSessionIpv6Dns1 indicates the primary DNS server. The value of this object is ''H when not applicable. The value of tmnxPppoeSessionOriginIpv6cpInfo indicates from what source this IP address was received.
IP tmnxPppoeSessionIpv6Dns2	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.46	InetAddress	read-only	The value of tmnxPppoeSessionIpv6Dns2 indicates the secondary DNS server. The value of this object is ''H when not applicable. The value of tmnxPppoeSessionOriginIpv6cpInfo indicates from what source this IP address was received.
IPt tmnxPppoeSessionIpv6DelPfxType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.47	InetAddressType	read-only	The value of tmnxPppoeSessionIpv6DelPfxType indicates the address type of tmnxPppoeSessionIpv6DelPfx.
ADR tmnxPppoeSessionIpv6DelPfxLen	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.48	InetAddressPrefixLength	read-only	The value of tmnxPppoeSessionIpv6DelPfxLen indicates the length of tmnxPppoeSessionIpv6DelPfx.
IP tmnxPppoeSessionIpv6DelPfx	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.49	InetAddress	read-only	The value of tmnxPppoeSessionIpv6DelPfx indicates the IPv6 prefix used for DHCPv6 prefix delegation.
IPt tmnxPppoeSessionIpv6PrefixType	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.50	InetAddressType	read-only	The value of tmnxPppoeSessionIpv6PrefixType indicates the address type of tmnxPppoeSessionIpv6Prefix.
ADR tmnxPppoeSessionIpv6PrefixLen	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.51	InetAddressPrefixLength	read-only	The value of tmnxPppoeSessionIpv6PrefixLen indicates the length of tmnxPppoeSessionIpv6Prefix.
IP tmnxPppoeSessionIpv6Prefix	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.52	InetAddress	read-only	The value of tmnxPppoeSessionIpv6Prefix indicates the IPv6 prefix used for stateless address autoconfiguration.
U32 tmnxPppoeSessionSubPppIndex	1.3.6.1.4.1.6527.3.1.2.49.1.8.1.53	Unsigned32	read-only	The value of tmnxPppoeSessionSubPppIndex indicates the local identifier of the subscriber PPP session. It is the index of the corresponding conceptual row in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppTable.
tmnxPppoeSessionModifyTable	1.3.6.1.4.1.6527.3.1.2.49.1.9		not-accessible	The tmnxPppoeSessionModifyTable augments the tmnxPppoeSessionTable. The table allows the operator to modify attributes of the PPPoE session. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppModTable.
tmnxPppoeSessionModifyEntry	1.3.6.1.4.1.6527.3.1.2.49.1.9.1		not-accessible	Each row entry contains parameters that allow to modify a PPPoE session's attributes.
STR tmnxPppoeSessionModSubIdent	1.3.6.1.4.1.6527.3.1.2.49.1.9.1.1	TmnxSubIdentStringOrEmpty	read-write	The value of tmnxPppoeSessionModSubIdent allows to specify a new subscriber name for this session. When a SET of this object is done with a non empty string, the system will attempt to assign a new subscriber name. A SET with an empty string has no effect on the system. (NOOP). GETs and GETNEXTs on this variable return an empty string.
STR tmnxPppoeSessionModSubProfStr	1.3.6.1.4.1.6527.3.1.2.49.1.9.1.2	TmnxSubProfileStringOrEmpty	read-write	The value of tmnxPppoeSessionModSubProfStr allows to specify a new subscriber profile string for this session. When a SET of this object is done with a non empty string, the system will attempt to assign a new subscriber profile string. A SET with an empty string has no effect on the system. (NOOP). GETs and GETNEXTs on this variable return an empty string.
STR tmnxPppoeSessionModSlaProfStr	1.3.6.1.4.1.6527.3.1.2.49.1.9.1.3	TmnxSlaProfileStringOrEmpty	read-write	The value of tmnxPppoeSessionModSlaProfStr allows to specify a new SLA profile string for this session. When a SET of this object is done with a non empty string, the system will attempt to assign a new SLA profile string. A SET with an empty string has no effect on the system. (NOOP). GETs and GETNEXTs on this variable return an empty string.
STR tmnxPppoeSessionModAncpStr	1.3.6.1.4.1.6527.3.1.2.49.1.9.1.4	TmnxAncpStringOrZero	read-write	The value of tmnxPppoeSessionModAncpStr allows to specify a new ANCP-string for this session. When a SET of this object is done with a non empty string, the system will attempt to assign a new ANCP-string. A SET with an empty string has no effect on the system. (NOOP). GETs and GETNEXTs on this variable return an empty string.
NUM tmnxPppoeSessionModInterDestId	1.3.6.1.4.1.6527.3.1.2.49.1.9.1.5	TmnxSubMgtIntDestIdOrEmpty	read-write	The value of tmnxPppoeSessionModInterDestId allows to specify a new intermediate destination id for this session. When a SET of this object is done with a non empty string, the system will attempt to assign a new intermediate destination id. A SET with an empty string has no effect on the system. (NOOP). GETs and GETNEXTs on this variable return an empty string.
STR tmnxPppoeSessionModAppProfStr	1.3.6.1.4.1.6527.3.1.2.49.1.9.1.6	TmnxAppProfileStringOrEmpty	read-write	The value of tmnxPppoeSessionModAppProfStr specifies a new application profile string for this session. When a SET of this object is done with a non empty string, the system will attempt to assign a new application profile string. A SET with an empty string has no effect on the system. (NOOP). GETs and GETNEXTs on this variable return an empty string.
T/F tmnxPppoeSessionEvaluateState	1.3.6.1.4.1.6527.3.1.2.49.1.9.1.7	TruthValue	read-write	The value of tmnxPppoeSessionEvaluateState allows to cause a re-evaluation of the specified session. When this object is set to 'true', the system will perform a re-evaluation of the session. GETs and GETNEXTs on this variable return false. It is not possible to simultaneously request for a session re-evaluation, and modify any of the strings.
tmnxPppoeSessionStatsTable	1.3.6.1.4.1.6527.3.1.2.49.1.10		not-accessible	A table that contains statistics per PPPoE session. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppStatTable.
tmnxPppoeSessionStatsEntry	1.3.6.1.4.1.6527.3.1.2.49.1.10.1		not-accessible	Statistics about a PPPoE session.
C32 tmnxPppoeSessionRxUnknownProto	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.1	Counter32	read-only	The value of tmnxPppoeSessionRxUnknownProto indicates the number of packets with unknown PPP protocol received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpConfReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.2	Counter32	read-only	The value of tmnxPppoeSessionRxLcpConfReq indicates the number of LCP configure requests received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpConfAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.3	Counter32	read-only	The value of tmnxPppoeSessionRxLcpConfAck indicates the number of LCP configure acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpConfNak	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.4	Counter32	read-only	The value of tmnxPppoeSessionRxLcpConfNak indicates the number of negative LCP configure acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpConfRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.5	Counter32	read-only	The value of tmnxPppoeSessionRxLcpConfRej indicates the number of LCP configure rejects received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpTermReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.6	Counter32	read-only	The value of tmnxPppoeSessionRxLcpTermReq indicates the number of LCP terminate requests received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpTermAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.7	Counter32	read-only	The value of tmnxPppoeSessionRxLcpTermAck indicates the number of LCP terminate acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpCodeRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.8	Counter32	read-only	The value of tmnxPppoeSessionRxLcpCodeRej indicates the number of LCP code rejects received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpEchoReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.9	Counter32	read-only	The value of tmnxPppoeSessionRxLcpEchoReq indicates the number of LCP echo requests received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpEchoRep	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.10	Counter32	read-only	The value of tmnxPppoeSessionRxLcpEchoRep indicates the number of LCP echo replies received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpProtRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.11	Counter32	read-only	The value of tmnxPppoeSessionRxLcpProtRej indicates the number of LCP protocol rejects received for this PPPoE session.
C32 tmnxPppoeSessionRxLcpDiscReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.12	Counter32	read-only	The value of tmnxPppoeSessionRxLcpDiscReq indicates the number of LCP discard requests received for this PPPoE session.
C32 tmnxPppoeSessionTxLcpConfReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.13	Counter32	read-only	The value of tmnxPppoeSessionTxLcpConfReq indicates the number of LCP configure requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpConfAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.14	Counter32	read-only	The value of tmnxPppoeSessionTxLcpConfAck indicates the number of LCP configure acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpConfNak	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.15	Counter32	read-only	The value of tmnxPppoeSessionTxLcpConfNak indicates the number of negative LCP configure acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpConfRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.16	Counter32	read-only	The value of tmnxPppoeSessionTxLcpConfRej indicates the number of LCP configure rejects transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpTermReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.17	Counter32	read-only	The value of tmnxPppoeSessionTxLcpTermReq indicates the number of LCP terminate requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpTermAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.18	Counter32	read-only	The value of tmnxPppoeSessionTxLcpTermAck indicates the number of LCP terminate acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpCodeRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.19	Counter32	read-only	The value of tmnxPppoeSessionTxLcpCodeRej indicates the number of LCP code rejects transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpEchoReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.20	Counter32	read-only	The value of tmnxPppoeSessionTxLcpEchoReq indicates the number of LCP echo requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpEchoRep	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.21	Counter32	read-only	The value of tmnxPppoeSessionTxLcpEchoRep indicates the number of LCP echo replies transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpProtRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.22	Counter32	read-only	The value of tmnxPppoeSessionTxLcpProtRej indicates the number of LCP protocol rejects transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxLcpDiscReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.23	Counter32	read-only	The value of tmnxPppoeSessionTxLcpDiscReq indicates the number of LCP discard requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionRxPapAuthReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.24	Counter32	read-only	The value of tmnxPppoeSessionRxPapAuthReq indicates the number of PAP authentication requests received for this PPPoE session.
C32 tmnxPppoeSessionTxPapAuthAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.25	Counter32	read-only	The value of tmnxPppoeSessionTxPapAuthAck indicates the number of PAP authentication acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxPapAuthNak	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.26	Counter32	read-only	The value of tmnxPppoeSessionTxPapAuthNak indicates the number of negative PAP authentication acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionRxChapResponse	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.27	Counter32	read-only	The value of tmnxPppoeSessionRxChapResponse indicates the number of CHAP authentication responses received for this PPPoE session.
C32 tmnxPppoeSessionTxChapChallenge	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.28	Counter32	read-only	The value of tmnxPppoeSessionTxChapChallenge indicates the number of CHAP authentication challenges transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxChapSuccess	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.29	Counter32	read-only	The value of tmnxPppoeSessionTxChapSuccess indicates the number of CHAP authentication acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxChapFailure	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.30	Counter32	read-only	The value of tmnxPppoeSessionTxChapFailure indicates the number of negative CHAP authentication acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionRxIpcpConfReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.31	Counter32	read-only	The value of tmnxPppoeSessionRxIpcpConfReq indicates the number of IPCP configure requests received for this PPPoE session.
C32 tmnxPppoeSessionRxIpcpConfAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.32	Counter32	read-only	The value of tmnxPppoeSessionRxIpcpConfAck indicates the number of IPCP configure acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxIpcpConfNak	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.33	Counter32	read-only	The value of tmnxPppoeSessionRxIpcpConfNak indicates the number of negative IPCP configure acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxIpcpConfRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.34	Counter32	read-only	The value of tmnxPppoeSessionRxIpcpConfRej indicates the number of IPCP configure rejects received for this PPPoE session.
C32 tmnxPppoeSessionRxIpcpTermReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.35	Counter32	read-only	The value of tmnxPppoeSessionRxIpcpTermReq indicates the number of IPCP terminate requests received for this PPPoE session.
C32 tmnxPppoeSessionRxIpcpTermAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.36	Counter32	read-only	The value of tmnxPppoeSessionRxIpcpTermAck indicates the number of IPCP terminate acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxIpcpCodeRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.37	Counter32	read-only	The value of tmnxPppoeSessionRxIpcpCodeRej indicates the number of IPCP code rejects received for this PPPoE session.
C32 tmnxPppoeSessionTxIpcpConfReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.38	Counter32	read-only	The value of tmnxPppoeSessionTxIpcpConfReq indicates the number of IPCP configure requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpcpConfAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.39	Counter32	read-only	The value of tmnxPppoeSessionTxIpcpConfAck indicates the number of IPCP configure acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpcpConfNak	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.40	Counter32	read-only	The value of tmnxPppoeSessionTxIpcpConfNak indicates the number of negative IPCP configure acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpcpConfRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.41	Counter32	read-only	The value of tmnxPppoeSessionTxIpcpConfRej indicates the number of IPCP configure rejects transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpcpTermReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.42	Counter32	read-only	The value of tmnxPppoeSessionTxIpcpTermReq indicates the number of IPCP terminate requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpcpTermAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.43	Counter32	read-only	The value of tmnxPppoeSessionTxIpcpTermAck indicates the number of IPCP terminate acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpcpCodeRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.44	Counter32	read-only	The value of tmnxPppoeSessionTxIpcpCodeRej indicates the number of IPCP code rejects transmitted for this PPPoE session.
C32 tmnxPppoeSessionRxIpv6cpConfReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.45	Counter32	read-only	The value of tmnxPppoeSessionRxIpv6cpConfReq indicates the number of IPv6CP configure requests received for this PPPoE session.
C32 tmnxPppoeSessionRxIpv6cpConfAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.46	Counter32	read-only	The value of tmnxPppoeSessionRxIpv6cpConfAck indicates the number of IPv6CP configure acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxIpv6cpConfNak	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.47	Counter32	read-only	The value of tmnxPppoeSessionRxIpv6cpConfNak indicates the number of negative IPv6CP configure acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxIpv6cpConfRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.48	Counter32	read-only	The value of tmnxPppoeSessionRxIpv6cpConfRej indicates the number of IPv6CP configure rejects received for this PPPoE session.
C32 tmnxPppoeSessionRxIpv6cpTermReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.49	Counter32	read-only	The value of tmnxPppoeSessionRxIpv6cpTermReq indicates the number of IPv6CP terminate requests received for this PPPoE session.
C32 tmnxPppoeSessionRxIpv6cpTermAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.50	Counter32	read-only	The value of tmnxPppoeSessionRxIpv6cpTermAck indicates the number of IPv6CP terminate acknowledgements received for this PPPoE session.
C32 tmnxPppoeSessionRxIpv6cpCodeRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.51	Counter32	read-only	The value of tmnxPppoeSessionRxIpv6cpCodeRej indicates the number of IPv6CP code rejects received for this PPPoE session.
C32 tmnxPppoeSessionTxIpv6cpConfReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.52	Counter32	read-only	The value of tmnxPppoeSessionTxIpv6cpConfReq indicates the number of IPv6CP configure requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpv6cpConfAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.53	Counter32	read-only	The value of tmnxPppoeSessionTxIpv6cpConfAck indicates the number of IPv6CP configure acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpv6cpConfNak	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.54	Counter32	read-only	The value of tmnxPppoeSessionTxIpv6cpConfNak indicates the number of negative IPv6CP configure acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpv6cpConfRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.55	Counter32	read-only	The value of tmnxPppoeSessionTxIpv6cpConfRej indicates the number of IPv6CP configure rejects transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpv6cpTermReq	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.56	Counter32	read-only	The value of tmnxPppoeSessionTxIpv6cpTermReq indicates the number of IPv6CP terminate requests transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpv6cpTermAck	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.57	Counter32	read-only	The value of tmnxPppoeSessionTxIpv6cpTermAck indicates the number of IPv6CP terminate acknowledgements transmitted for this PPPoE session.
C32 tmnxPppoeSessionTxIpv6cpCodeRej	1.3.6.1.4.1.6527.3.1.2.49.1.10.1.58	Counter32	read-only	The value of tmnxPppoeSessionTxIpv6cpCodeRej indicates the number of IPv6CP code rejects transmitted for this PPPoE session.
tmnxPppoeManagedRouteTable	1.3.6.1.4.1.6527.3.1.2.49.1.11		not-accessible	A table that contains PPPoE managed routes. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppMRtTable.
tmnxPppoeManagedRouteEntry	1.3.6.1.4.1.6527.3.1.2.49.1.11.1		not-accessible	A specific PPPoE managed route.
IPt tmnxPppoeManagedRouteAddrType	1.3.6.1.4.1.6527.3.1.2.49.1.11.1.1	InetAddressType	not-accessible	The value of tmnxPppoeManagedRouteAddrType indicates the address type of tmnxPppoeManagedRouteAddr.
IP tmnxPppoeManagedRouteAddr	1.3.6.1.4.1.6527.3.1.2.49.1.11.1.2	InetAddress	not-accessible	The value of tmnxPppoeManagedRouteAddr indicates the IP address of the managed route.
ADR tmnxPppoeManagedRoutePrefixLen	1.3.6.1.4.1.6527.3.1.2.49.1.11.1.3	InetAddressPrefixLength	not-accessible	The value of tmnxPppoeManagedRoutePrefixLen indicates the prefix length of the subnet associated with tmnxPppoeManagedRouteAddr.
TMN tmnxPppoeManagedRouteStatus	1.3.6.1.4.1.6527.3.1.2.49.1.11.1.4	TmnxManagedRouteStatus	read-only	The value of tmnxPppoeManagedRouteStatus indicates the state of this managed route.
tmnxPppoeSessionBgpTable	1.3.6.1.4.1.6527.3.1.2.49.1.12		not-accessible	The tmnxPppoeSessionBgpTable augments the tmnxPppoeSessionTable. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppBgpTable.
tmnxPppoeSessionBgpEntry	1.3.6.1.4.1.6527.3.1.2.49.1.12.1		not-accessible	A row entry contains parameters used for a BGP peering.
TNA tmnxPppoeSessionBgpPrngPlcyName	1.3.6.1.4.1.6527.3.1.2.49.1.12.1.1	TNamedItemOrEmpty	read-only	The value of tmnxPppoeSessionBgpPrngPlcyName indicates the peering policy which is used to set up the BGP peer for this pppoe session.
TNA tmnxPppoeSessionBgpAuthKeyChain	1.3.6.1.4.1.6527.3.1.2.49.1.12.1.2	TNamedItemOrEmpty	read-only	The value of tmnxPppoeSessionBgpAuthKeyChain indicates the keychain which is used to sign and/or authenticate the BGP protocol stream.
OCT tmnxPppoeSessionBgpMD5AuthKey	1.3.6.1.4.1.6527.3.1.2.49.1.12.1.3	OCTET STRING	read-only	The value of tmnxPppoeSessionBgpMD5AuthKey indicates the authentication key used between BGP peers neighbors before establishing sessions. Authentication is done using the MD-5 message based digest protocol.
TPO tmnxPppoeSessionBgpImportPolicy	1.3.6.1.4.1.6527.3.1.2.49.1.12.1.4	TPolicyStatementNameOrEmpty	read-only	The value of tmnxPppoeSessionBgpImportPolicy indicates the import policy.
TPO tmnxPppoeSessionBgpExportPolicy	1.3.6.1.4.1.6527.3.1.2.49.1.12.1.5	TPolicyStatementNameOrEmpty	read-only	The value of tmnxPppoeSessionBgpExportPolicy indicates the export policy.
INE tmnxPppoeSessionBgpPeerAS	1.3.6.1.4.1.6527.3.1.2.49.1.12.1.6	InetAutonomousSystemNumber	read-only	The value of tmnxPppoeSessionBgpPeerAS indicates the Autonomous System number for the remote peer.
BGP tmnxPppoeSessionBgpPeeringStatus	1.3.6.1.4.1.6527.3.1.2.49.1.12.1.7	BgpPeeringStatus	read-only	The value of tmnxPppoeSessionBgpPeeringStatus indicates the status of the BGP peering session.
tmnxPppoeSessionOverridesTable	1.3.6.1.4.1.6527.3.1.2.49.1.13		not-accessible	A table that contains PPPoE session qos overrides. This table is replace with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppOvrTable.
tmnxPppoeSessionOverridesEntry	1.3.6.1.4.1.6527.3.1.2.49.1.13.1		not-accessible	Information about a specific PPPoE session qos override.
TDI tmnxPppoeSessionOvrDirection	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.1	TDirection	not-accessible	The value of tmnxPppoeSessionOvrDirection indicates whether this row specifies ingress or egress qos override parameters.
TQO tmnxPppoeSessionOvrType	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.2	TQosOverrideType	not-accessible	The value of tmnxPppoeSessionOvrType indicates what field has been overwritten by this row.
I32 tmnxPppoeSessionOvrTypeId	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.3	Integer32	not-accessible	The value of tmnxPppoeSessionOvrTypeId indicates the id of the queue/policer that has been overwritten by this row. If the value of tmnxPppoeSessionOvrType is not 'queue (1)' or 'policer (2)', this field must be set to zero (0).
TNA tmnxPppoeSessionOvrTypeName	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.4	TNamedItemOrEmpty	not-accessible	The value of tmnxPppoeSessionOvrTypeName indicates the name of the scheduler/arbiter that has been overwritten by this row. If the value of tmnxPppoeSessionOvrType is not 'arbiter (4)' or 'scheduler (5)', this field must be set to zero (0).
TPI tmnxPppoeSessionOvrPIR	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.5	TPIRRateOverride	read-only	The value of tmnxPppoeSessionOvrPIR indicates the PIR rate in kbps allowed for the object overwritten by this row.
TCI tmnxPppoeSessionOvrCIR	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.6	TCIRRateOverride	read-only	The value of tmnxPppoeSessionOvrCIR indicates the CIR rate in kbps allowed for the object overwritten by this row.
TBU tmnxPppoeSessionOvrCBS	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.7	TBurstSizeBytesOverride	read-only	The value of tmnxPppoeSessionOvrCBS indicates the amount of reserved buffer space (in bytes) for the object overwritten by this row.
TBU tmnxPppoeSessionOvrMBS	1.3.6.1.4.1.6527.3.1.2.49.1.13.1.8	TBurstSizeBytesOverride	read-only	The value of tmnxPppoeSessionOvrMBS indicates the maximum amount of reserved buffer space (in bytes) for the object overwritten by this row.
tmnxPppoeSessionAleTable	1.3.6.1.4.1.6527.3.1.2.49.1.15		not-accessible	A table that contains PPPoE session Access Loop Encapsulation information. Entries in this table are created and destroyed by the system. This table is a sparse augment of the tmnxPppoeSessionTable: entries are created only for PPPoE sessions for which Access Loop Encapsulation information is available. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppAleTable
tmnxPppoeSessionAleEntry	1.3.6.1.4.1.6527.3.1.2.49.1.15.1		not-accessible	Access Loop Encapsulation Information about a specific PPPoE session.
TMN tmnxPppoeSessionAleDatalink	1.3.6.1.4.1.6527.3.1.2.49.1.15.1.1	TmnxAccessLoopEncapDataLink	read-only	The value of tmnxPppoeSessionAleDatalink indicates the data link used by the subscriber host on the DSL access loop.
TMN tmnxPppoeSessionAleEncaps1	1.3.6.1.4.1.6527.3.1.2.49.1.15.1.2	TmnxAccessLoopEncaps1	read-only	The value of tmnxPppoeSessionAleEncaps1 indicates the encapsulation used by the subscriber host on the DSL access loop.
TMN tmnxPppoeSessionAleEncaps2	1.3.6.1.4.1.6527.3.1.2.49.1.15.1.3	TmnxAccessLoopEncaps2	read-only	The value of tmnxPppoeSessionAleEncaps2 indicates the encapsulation used by the subscriber host on the DSL access loop.
tmnxPppoeNotificationObjs	1.3.6.1.4.1.6527.3.1.2.49.2
STR tmnxPppoeSessionFailureReason	1.3.6.1.4.1.6527.3.1.2.49.2.1	DisplayString	accessible-for-notify	The object tmnxPppoeSessionFailureReason indicates the problem encountered by the system while trying to create a new PPPoE session in the tmnxPppoeSessionTable.
INT tmnxPppoeNcpFailureProtocol	1.3.6.1.4.1.6527.3.1.2.49.2.2	INTEGER	accessible-for-notify	The value of tmnxPppoeNcpFailureProtocol indicates the failing NCP protocol.
STR tmnxPppoeNcpFailureReason	1.3.6.1.4.1.6527.3.1.2.49.2.3	DisplayString	accessible-for-notify	The object tmnxPppoeNcpFailureReason indicates the problem encountered by the system during NCP phase.
STR tmnxPppoeNotifyDescription	1.3.6.1.4.1.6527.3.1.2.49.2.4	DisplayString	accessible-for-notify	The object tmnxPppoeNotifyDescription is a printable character string.
tmnxPppObjects	1.3.6.1.4.1.6527.3.1.2.49.3
TIM tmnxPppIesIfTableLastChg	1.3.6.1.4.1.6527.3.1.2.49.3.1	TimeStamp	read-only	The value of tmnxPppIesIfTableLastChg indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxPppIesIfTable.
tmnxPppIesIfTable	1.3.6.1.4.1.6527.3.1.2.49.3.2		not-accessible	A table that contains IES interface PPP configuration information. A row is automatically created in the tmnxPppIesIfTable for an entry in the iesIfTable where the value of the object iesIfType is equal to 'group (3)'.
tmnxPppIesIfEntry	1.3.6.1.4.1.6527.3.1.2.49.3.2.1		not-accessible	PPP specific information about an IES interface.
TIM tmnxPppIesIfLastChg	1.3.6.1.4.1.6527.3.1.2.49.3.2.1.1	TimeStamp	read-only	The value of tmnxPppIesIfLastChg indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TIT tmnxPppIesIfDescription	1.3.6.1.4.1.6527.3.1.2.49.3.2.1.2	TItemDescription	read-write	The value of the object tmnxPppIesIfDescription specifies a user provided description for PPP on this IES interface.
TMN tmnxPppIesIfAdminState	1.3.6.1.4.1.6527.3.1.2.49.3.2.1.3	TmnxPppoeAdminStatus	read-write	The value of the object tmnxPppIesIfAdminState specifies the administrative state of PPP on this IES interface.
TNA tmnxPppIesIfPolicy	1.3.6.1.4.1.6527.3.1.2.49.3.2.1.4	TNamedItem	read-write	The value of tmnxPppIesIfPolicy specifies the PPP policy applicable on this IES interface.
U32 tmnxPppIesIfSessionLimit	1.3.6.1.4.1.6527.3.1.2.49.3.2.1.5	Unsigned32	read-write	The value of tmnxPppIesIfSessionLimit specifies the maximum number of PPP sessions allowed on this IES interface.
TNA tmnxPppIesIfUserDb	1.3.6.1.4.1.6527.3.1.2.49.3.2.1.8	TNamedItemOrEmpty	read-write	The value of tmnxPppIesIfUserDb specifies the local user database to use for PPP PAP/CHAP based authentication. If no authentication with the local user database is required, the value of this object must be set to the empty string.
tmnxMlpppObjects	1.3.6.1.4.1.6527.3.1.2.49.3.3
tmnxMlpppBundleTable	1.3.6.1.4.1.6527.3.1.2.49.3.3.1		not-accessible	The tmnxMlpppBundleTable allows the monitoring of subscriber MLPPP (Multi Link PPP) Bundles.
tmnxMlpppBundleEntry	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1		not-accessible	Each conceptual row represents a subscriber MLPPP Bundle. Entries in this table are created and destroyed by the system.
U32 tmnxMlpppBundleIndex	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.1	Unsigned32	not-accessible	The value of the object tmnxMlpppBundleIndex indicates the local identifier of the bundle.
TMN tmnxMlpppBundleLocEpClass	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.2	TmnxMlpppEpClass	read-only	The value of tmnxMlpppBundleLocEpClass indicates the address class of the local endpoint. If the value of tmnxMlpppBundleLocEpClass is equal to 'null', the address class of the MLPPP Endpoint Discriminator option was not present in a received Configure-Request.
OCT tmnxMlpppBundleLocEpAddress	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.3	OCTET STRING	read-only	The value of tmnxMlpppBundleLocEpAddress indicates the address of the local MLPPP Endpoint. Its interpretation depends on the value of tmnxMlpppBundleLocEpClass.
TMN tmnxMlpppBundleRemEpClass	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.4	TmnxMlpppEpClass	read-only	The value of tmnxMlpppBundleRemEpClass indicates the address class of the local endpoint. If the value of tmnxMlpppBundleRemEpClass is equal to 'null', the address class of the MLPPP Endpoint Discriminator option was not present in a received Configure-Request.
OCT tmnxMlpppBundleRemEpAddress	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.5	OCTET STRING	read-only	The value of tmnxMlpppBundleRemEpAddress indicates the address of the local MLPPP Endpoint. Its interpretation depends on the value of tmnxMlpppBundleRemEpClass.
U32 tmnxMlpppBundleSubPppIndex	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.6	Unsigned32	read-only	The value of tmnxMlpppBundleSubPppIndex indicates the local identifier of the subscriber PPP session. It is the index of the corresponding conceptual row in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppTable.
U32 tmnxMlpppBundleMaxLinks	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.7	Unsigned32	read-only	The value of tmnxMlpppBundleMaxLinks indicates the maximum number of links allowed for this bundle.
G32 tmnxMlpppBundleActualLinks	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.8	Gauge32	read-only	The value of tmnxMlpppBundleActualLinks indicates the actual number of links of this bundle.
U32 tmnxMlpppBundleRemMrru	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.9	Unsigned32	read-only	The value of tmnxMlpppBundleRemMrru indicates the Maximum Reconstructed Receive Unit (MRRU) for this MLPPP bundle. This value is derived from the values proposed by the MLPPP peer for the MLPPP links in this bundle.
U32 tmnxMlpppBundleLocMrru	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.10	Unsigned32	read-only	The value of tmnxMlpppBundleLocMrru indicates the Maximum Reconstructed Receive Unit (MRRU) for this MLPPP bundle.
BIT tmnxMlpppBundleIndicators	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.11	Bits	read-only	The value of tmnxMlpppBundleIndicators indicates various information about this bundle. lfiCfg - Link Fragmentation and Interleaving (LFI) configured when this bundle was created; lfi - LFI active; shortSeqNrRx - Short Sequence Numbers used for incoming messages; shortSeqNrTx - Short Sequence Numbers for outgoing messages.
U32 tmnxMlpppBundleFragmentSize	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.12	Unsigned32	read-only	The value of tmnxMlpppBundleFragmentSize indicates the fragment size for this bundle. While there is no fragmentation and interleaving on this bundle, the value of this object is equal to zero.
U32 tmnxMlpppBundleMaxDelayCfg	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.13	Unsigned32	read-only	The value of tmnxMlpppBundleMaxDelayCfg indicates the maximum delay configured for this bundle when it was created.
U32 tmnxMlpppBundleMaxDelay	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.14	Unsigned32	read-only	The value of tmnxMlpppBundleMaxDelay indicates the maximum delay for this bundle.
U32 tmnxMlpppBundleReassemblyTo	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.15	Unsigned32	read-only	The value of tmnxMlpppBundleReassemblyTo indicates the reassembly timeout configured for this bundle when it was created.
U32 tmnxMlpppBundleEgressRate	1.3.6.1.4.1.6527.3.1.2.49.3.3.1.1.16	Unsigned32	read-only	The value of tmnxMlpppBundleEgressRate indicates the nominal egress rate for this bundle.
tmnxMlpppLinkTable	1.3.6.1.4.1.6527.3.1.2.49.3.3.2		not-accessible	The tmnxMlpppLinkTable contains the subscriber MLPPP (Multi Link PPP) link sessions ordered per bundle.
tmnxMlpppLinkEntry	1.3.6.1.4.1.6527.3.1.2.49.3.3.2.1		not-accessible	Each conceptual row represents a subscriber MLPPP link. Entries in this table are created and destroyed by the system.
U32 tmnxMlpppLinkRemMrru	1.3.6.1.4.1.6527.3.1.2.49.3.3.2.1.1	Unsigned32	read-only	The value of tmnxMlpppLinkRemMrru indicates the Maximum Reconstructed Receive Unit (MRRU) proposed by the MLPPP peer for this MLPPP link.
TIM tmnxPppPlcyMlpppTableLastCh	1.3.6.1.4.1.6527.3.1.2.49.3.3.3	TimeStamp	read-only	The value of tmnxPppPlcyMlpppTableLastCh indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxPppPlcyMlpppTable.
tmnxPppPlcyMlpppTable	1.3.6.1.4.1.6527.3.1.2.49.3.3.4		not-accessible	The tmnxPppPlcyMlpppTable has an entry for each PPP(oE) policy configured in the system. This table can be used to configure MLPPP for PPPoE (PPP over Ethernet) and PPPoA (PPP over ATM) subscribers.
tmnxPppPlcyMlpppEntry	1.3.6.1.4.1.6527.3.1.2.49.3.3.4.1		not-accessible	Each row entry represents MLPPP information of a PPP(oE) policy configured in the system. Conceptual rows are created and destroyed automatically by the system.
TIM tmnxPppPlcyMlpppLastCh	1.3.6.1.4.1.6527.3.1.2.49.3.3.4.1.1	TimeStamp	read-only	The value of tmnxPppPlcyMlpppLastCh indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
T/F tmnxPppPlcyMlpppAcceptMrru	1.3.6.1.4.1.6527.3.1.2.49.3.3.4.1.2	TruthValue	read-create	The value of tmnxPppPlcyMlpppAcceptMrru specifies if this system will accept the Multilink MRRU LCP option for the PPP sessions using this policy.
TMN tmnxPppPlcyMlpppEpClass	1.3.6.1.4.1.6527.3.1.2.49.3.3.4.1.3	TmnxMlpppEpClass	read-create	The value of tmnxPppPlcyMlpppEpClass specifies the type of endpoint. If the value of 'tmnxPppPlcyMlpppEpClass' is equal to 'ipv4Address', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxPppPlcyMlpppEpIpv4Address. If the value of 'tmnxPppPlcyMlpppEpClass' is equal to 'macAddress', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxPppPlcyMlpppEpMacAddress. If the value of 'tmnxPppPlcyMlpppEpClass' is equal to 'null', the MLPPP Endpoint Discriminator Option must not be transmitted. A value other than 'null' is only allowed if this system performs the role of LAC with respect to the PPP clients using this policy.
ADR tmnxPppPlcyMlpppEpIpv4Address	1.3.6.1.4.1.6527.3.1.2.49.3.3.4.1.4	InetAddressIPv4	read-create	The value of tmnxPppPlcyMlpppEpIpv4Address specifies the class 2 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxPppPlcyMlpppEpClass is equal to 'ipv4Address', a value of all zeroes specifies that the system IP address be used; otherwise, it means that no address is specified.
MAC tmnxPppPlcyMlpppEpMacAddress	1.3.6.1.4.1.6527.3.1.2.49.3.3.4.1.5	MacAddress	read-create	The value of tmnxPppPlcyMlpppEpMacAddress specifies the class 3 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxPppPlcyMlpppEpClass is equal to 'macAddress', a value of all zeroes specifies that the system MAC address be used; otherwise, it means that no address is specified.
T/F tmnxPppPlcyMlpppShortSeqNumberRx	1.3.6.1.4.1.6527.3.1.2.49.3.3.4.1.6	TruthValue	read-create	The value of tmnxPppPlcyMlpppShortSeqNumberRx specifies if this system requests to receive short sequence numbers from the peer. If the value of this object is 'true', this system includes the Short Sequence Number Header Format Option in its LCP configuration options. If the value of this object is 'false', this system does not includes the Short Sequence Number Header Format Option in its LCP configuration options.
tmnxPppoeNotifyPrefix	1.3.6.1.4.1.6527.3.1.3.49
tmnxPppoeNotifications	1.3.6.1.4.1.6527.3.1.3.49.0
NTF tmnxPppoeSessionFailure	1.3.6.1.4.1.6527.3.1.3.49.0.1			The tmnxPppoeSessionFailure notification indicates that the system could not create a new PPPoE session in the tmnxPppoeSessionTable. The problem is described in the object tmnxPppoeSessionFailureReason.
NTF tmnxPppoeNcpFailure	1.3.6.1.4.1.6527.3.1.3.49.0.2			The tmnxPppoeNcpFailure notification indicates that there is a NCP phase setup problem.
NTF tmnxMlpppBundleIndicatorsChange	1.3.6.1.4.1.6527.3.1.3.49.0.3			The tmnxMlpppBundleIndicatorsChange notification indicates that the value of the object tmnxMlpppBundleIndicatorsChange has changed. [CAUSE] The value of the object tmnxMlpppBundleIndicatorsChange has changed. A particular change is the change from 'lfi\|lfiCfg' to 'lfiCfg': since interleaving is only supported on bundles with a single link, interleaving is disabled when a second link is added to a bundle. [EFFECT] When the value of the object tmnxMlpppBundleIndicatorsChange changes from 'lfi\|lifCfg' to 'lfiCfg', Link Fragmentation and Interleaving (LFI) is disabled on the bundle.

RFC description

Manages PPP over Ethernet (PPPoE) sessions on Alcatel-Lucent service routing platforms.

Start monitoring Nokia/Alcatel-Lucent 7750 SR broadband network gateway (PPPoE policy/keepalive status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TIMETRA-PPPOE-MIB