TIMETRA-ETH-RING-MIB

All MIBs › TIMETRA-ETH-RING-MIB

Organization: Alcatel-Lucent

Last Updated: 2011-02-01

Description: TIMETRA-ETH-RING-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TIMETRA-ETH-RING-MIB?

This Nokia/Alcatel-Lucent proprietary MIB manages Ethernet Ring Protection Switching rings on the 7750 SR SROS platform, a Layer-2 resiliency technology for looped Ethernet topologies. It exposes ring configuration objects (ring index, description, guard time, revert time) alongside operational and administrative state for each ring instance. It's directly useful for monitoring the software health of the ring protocol itself: tmnxEthRingAdminState and tmnxEthRingOperState reveal whether a ring is administratively enabled and actually passing traffic, while the revert timers show whether a ring is mid-recovery after a fault. As a Nokia SROS extension it builds on the vendor's common textual-convention MIB and relates to the underlying Ethernet/interface MIBs for the physical ports carrying the ring. It's typically deployed in metro Ethernet and carrier access networks using 7750 SR/7450 ESS nodes arranged in ring topologies for fast failover, where TIMETRA-ETH-RING-MIB SNMP monitoring confirms ring state during protection-switching events.

IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-ETH-RING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nokia/Alcatel-Lucent 7750 SR
7450 ESS metro Ethernet switch/router

Monitoring Examples

An operator polls tmnxEthRingConfigTable / tmnxEthRingConfigEntry indexed by tmnxEthRingIndex to compare tmnxEthRingAdminState against tmnxEthRingOperState -- a ring administratively up but operationally down indicates a break or misconfigured guard/revert timing. Watching tmnxEthRingRevertTimeCountDn during a tmnxEthRingRevertTime window shows whether the ring is actively counting down to revert to its idle topology after a fault has cleared, and tmnxEthRingTimeStamp records when the ring's state last changed for correlation with other network events.

What Can Be Monitored

ring administrative state
ring operational state
guard time
revert time countdown
ring last-changed timestamp

Imported Objects

From IF-MIB

InterfaceIndexOrZero

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

From TIMETRA-GLOBAL-MIB

timetraSRMIBModules	OBJECT-IDENTITY
tmnxSRConfs	OBJECT-IDENTITY
tmnxSRNotifyPrefix	OBJECT-IDENTITY
tmnxSRObjs	OBJECT-IDENTITY

From TIMETRA-SAP-MIB

sapEncapValue	OBJECT-TYPE
sapPortId	OBJECT-TYPE

From TIMETRA-SERV-MIB

svcId

OBJECT-TYPE

From TIMETRA-TC-MIB

TItemDescription
TmnxAdminState
TmnxEncapVal
TmnxOperState

OIDs

OID symbolic	OID numeric	Type	Access	Description
timetraEthRingMIBModule	1.3.6.1.4.1.6527.1.1.3.72			This document is the SNMP MIB module to manage and provision the Ethernet Ring components of the Alcatel-Lucent SROS device. Copyright (c) 2009-2011 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
tmnxEthRingConformance	1.3.6.1.4.1.6527.3.1.1.72
tmnxEthRingCompliances	1.3.6.1.4.1.6527.3.1.1.72.1
tmnxEthRingCompliance	1.3.6.1.4.1.6527.3.1.1.72.1.1			The compliance statement for revision 1.0 of TIMETRA-ETH-RING-MIB.
tmnxEthRingV9v0Compliance	1.3.6.1.4.1.6527.3.1.1.72.1.2			The compliance statement for revision 9.0 of TIMETRA-ETH-RING-MIB.
tmnxEthRingGroups	1.3.6.1.4.1.6527.3.1.1.72.2
tmnxEthRingTSGroups	1.3.6.1.4.1.6527.3.1.1.72.2.0
tmnxEthRingTimeStampGroup	1.3.6.1.4.1.6527.3.1.1.72.2.0.1			The group of objects that track configuration changes for the maintenance of Ethernet Rings for the 7x50.
tmnxEthRingConfigGroups	1.3.6.1.4.1.6527.3.1.1.72.2.1
tmnxEthRingBaseConfigGroup	1.3.6.1.4.1.6527.3.1.1.72.2.1.1			The group of objects for management of Ethernet Ring Group configurations for the 7x50.
tmnxEthRingOperGroups	1.3.6.1.4.1.6527.3.1.1.72.2.2
tmnxEthRingMemberGroups	1.3.6.1.4.1.6527.3.1.1.72.2.3
tmnxEthRingBasePathGroup	1.3.6.1.4.1.6527.3.1.1.72.2.3.1			The group of objects for management of Ethernet Ring Group Member configurations for the 7x50.
tmnxEthRingAPSGroups	1.3.6.1.4.1.6527.3.1.1.72.2.4
tmnxEthRingNotifyGroups	1.3.6.1.4.1.6527.3.1.1.72.2.5
tmnxEthRingOperNotifyGroup	1.3.6.1.4.1.6527.3.1.1.72.2.5.1			The group of notifications for management of Ethernet Ring Group configurations for the SR series systems.
tmnxEthRingApsNotifyGroup	1.3.6.1.4.1.6527.3.1.1.72.2.5.2			The group of notifications for management of Ethernet Ring Group APS configurations for the SR series systems.
tmnxEthRingSAPGroups	1.3.6.1.4.1.6527.3.1.1.72.2.6
tmnxEthRingSAPPathGroup	1.3.6.1.4.1.6527.3.1.1.72.2.6.1			The group of objects added in Release 8.0 to support configuration and maintenance of Ethernet Ring Groups on SAPs for the 7x50.
tmnxEthRingV9v0Groups	1.3.6.1.4.1.6527.3.1.1.72.2.7
tmnxEthRingBaseConfigV9v0Group	1.3.6.1.4.1.6527.3.1.1.72.2.7.1			The group of objects added in Release 9.0 to support configuration and maintenance of Ethernet Rings for the SROS series systems.
tmnxEthRingSubRingV9v0Group	1.3.6.1.4.1.6527.3.1.1.72.2.7.2			The group of objects added in Release 9.0 to support configuration and maintenance of Ethernet sub-rings for the SROS series systems.
tmnxEthRingCommandV9v0Group	1.3.6.1.4.1.6527.3.1.1.72.2.7.3			The group of objects added in Release 9.0 to support maintenance of Ethernet Rings for the SROS series systems.
tmnxEthRingObjs	1.3.6.1.4.1.6527.3.1.2.72
tmnxEthRingConfigTimeStamps	1.3.6.1.4.1.6527.3.1.2.72.0
TIM tmnxEthRingCfgTblLastChanged	1.3.6.1.4.1.6527.3.1.2.72.0.1	TimeStamp	read-only	The tmnxEthRingCfgTblLastChanged indicates the time, since system startup, when a row in the tmnxEthRingConfigTable last changed.
TIM tmnxEthRingPathTblLastChanged	1.3.6.1.4.1.6527.3.1.2.72.0.2	TimeStamp	read-only	The tmnxEthRingPathTblLastChanged indicates the time, since system startup, when a row in the tmnxEthRingPathTable last changed.
TIM tmnxEthRingSAPPathTblChanged	1.3.6.1.4.1.6527.3.1.2.72.0.4	TimeStamp	read-only	The tmnxEthRingSAPPathTblChanged indicates the time, since system startup, when a row in the tmnxEthRingSAPPathTable last changed.
tmnxEthRingConfigurations	1.3.6.1.4.1.6527.3.1.2.72.1
tmnxEthRingConfigTable	1.3.6.1.4.1.6527.3.1.2.72.1.1		not-accessible	The tmnxEthRingConfigTable consists of the Ethernet Ring configuration information.
tmnxEthRingConfigEntry	1.3.6.1.4.1.6527.3.1.2.72.1.1.1		not-accessible	The tmnxEthRingConfigEntry contains information pertaining to an individual Ethernet Ring. Rows in this table are created and destroyed using the tmnxEthRingRowStatus object.
TMN tmnxEthRingIndex	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.1	TmnxEthRingIndex	not-accessible	The value of tmnxEthRingIndex specifies the row index of the Ethernet Ring Group.
ROW tmnxEthRingRowStatus	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.2	RowStatus	read-create	The value of tmnxEthRingRowStatus controls the creation and deletion of row entries in the tmnxEthRingConfigTable.
TIM tmnxEthRingTimeStamp	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.3	TimeStamp	read-only	The value of tmnxEthRingTimeStamp indicates the time, since system startup, of the last change to this row.
TIT tmnxEthRingDescription	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.4	TItemDescription	read-create	The value of tmnxEthRingDescription specifies the user supplied description of the Ethernet Ring.
TMN tmnxEthRingAdminState	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.5	TmnxAdminState	read-create	The value of tmnxEthRingAdminState specifies the administrative state of the Ethernet Ring.
TMN tmnxEthRingOperState	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.6	TmnxOperState	read-only	The value of tmnxEthRingOperState indicates the operational state of the Ethernet Ring.
U32 tmnxEthRingGuardTime	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.7	Unsigned32	read-create	The value of tmnxEthRingGuardTime specifies the guard timer, in deciseconds, of a Ring-APS (R-APS) node. The guard timer is used to prevent the Ethernet Ring node from acting upon outdated R-APS messages and prevent the possibility of forming a closed loop. While the guard timer is running, any received R-APS Request/State and Status information is blocked and not forwarded to the Priority Logic. When the guard timer is not running, the R-APS Request/State and Status information is forwarded unchanged.
U32 tmnxEthRingRevertTime	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.8	Unsigned32	read-create	The value of tmnxEthRingRevertTime specifies the Wait-To-Restore (WTR) timer, in seconds, of a Ring-APS (R-APS) node. The WTR timer is used to prevent frequent operation of the protection switching due to intermittent signal failure defects. Setting tmnxEthRingRevertTime to the value zero (0) puts the Ethernet Ring into a non-revertive mode.
U32 tmnxEthRingRevertTimeCountDn	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.9	Unsigned32	read-only	The value of tmnxEthRingRevertTimeCountDn indicates the remaining time, in seconds, before the Ethernet Ring can revert to its original state.
U32 tmnxEthRingCcmHoldDownTime	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.10	Unsigned32	read-create	The value of tmnxEthRingCcmHoldDownTime specifies the time, in centiseconds, used for the hold-timer for associated Continuity Check (CC) Session down event dampening. This guards against reporting excessive path operational state transitions. This is implemented by not advertising subsequent transitions of the CC state to the Ethernet Ring Node until the configured timer has expired. A value of zero (0) specifies that a down transition is reported immediately.
U32 tmnxEthRingCcmHoldUpTime	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.11	Unsigned32	read-create	The value of tmnxEthRingCcmHoldUpTime specifies the time, in deciseconds, used for the hold-timer for associated Continuity Check (CC) Session up event dampening. This guards against reporting excessive path operational state transitions. This is implemented by not advertising subsequent transitions of the CC state to the Ethernet Ring Node until the configured timer has expired. A value of zero (0) specifies that an up transition is reported immediately.
TMN tmnxEthRingRplNode	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.12	TmnxEthRingRplNodeType	read-create	The value of tmnxEthRingRplNode specifies the Ring Protection Link (RPL) type of the Ethernet Ring Node.
MAC tmnxEthRingNodeId	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.13	MacAddress	read-create	The value of tmnxEthRingNodeId specifies the Ethernet Ring Node ID. The default value is the system's MAC address. Writing the MAC address value 00:00:00:00:00:00 to tmnxEthRingNodeId will reset its value to the system's MAC address.
TMN tmnxEthRingTxApsPdu	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.14	TmnxEthRingApsInfoType	read-only	The value of tmnxEthRingTxApsPdu indicates the contents of the R-APS PDU transmitted on the Ethernet Ring.
BIT tmnxEthRingDefectStatus	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.15	Bits	read-only	The value of tmnxEthRingDefectStatus indicates what defects are active on the Ethernet Ring. The defects are defined as: dFopPM -- Provisioning Mismatch
INT tmnxEthRingSubRingType	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.16	INTEGER	read-create	The value of tmnxEthRingSubRingType specifies whether this Ethernet Ring is a sub-ring or not. A value of 'none (0)' specifies that the Ethernet Ring is not a sub-ring. A value 'virtualLink (1)' specifies that the Ethernet Ring is a sub-ring with R-APS virtual channel, while the value 'nonVirtualLink (2)' specifies that the Ethernet Ring is a sub-ring without R-APS virtual channel. This object MUST be set to a value other than 'none (0)' for tmnxEthRingSubRingInterconnectId and tmnxEthRingSubRingPropTopChange to be modified away from their default values.
U32 tmnxEthRingSubRingInterconnectId	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.17	Unsigned32	read-create	The value of tmnxEthRingSubRingInterconnectId specifies whether the Ethernet sub-ring is interconnected to an Ethernet Ring, as identified by the Ethernet Ring ID, a VPLS service (4294967295), or is not interconnected (0). A sub-ring can only be interconnected to a VPLS service (i.e. tmnxEthRingSubRingInterconnectId assigned the value 4294967295), if tmnxEthRingSubRingType is assigned the value 'nonVirtualLink (2)'. This object MUST be set to a value other than zero (0) for tmnxEthRingSubRingPropTopChange to be modified away from its default value. Attempts to modify this object away from its default value when tmnxEthRingSubRingType is set to 'none (0)' will result in an SNMP inconsistentValue error.
T/F tmnxEthRingSubRingPropTopChange	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.18	TruthValue	read-create	The value of tmnxEthRingSubRingPropTopChange specifies whether or not the Ethernet sub-ring propagates topology changes to the interconnected ring as specified by the value of tmnxEthRingSubRingInterconnectId. Attempts to modify this object away from its default value when tmnxEthRingSubRingInterconnectId is set to zero (0) will result in an SNMP inconsistentValue error.
INT tmnxEthRingCompatibleVersion	1.3.6.1.4.1.6527.3.1.2.72.1.1.1.19	INTEGER	read-create	The value of tmnxEthRingCompatibleVersion specifies the backward compatibility logic for the Ethernet Ring. If this object is set to 'version1 (1)' then: 1. Attempts at setting tmnxEthRingCommandSwitch to the value 'forceSwitch (2)' or 'manualSwitch (3)' will result in an inconsistentValue error, and 2. Attempts at setting tmnxEthRingRevertTime to the value zero (0) will result in an inconsistentValue error. If this object is set to 'version2 (2)' then the above restrictions will not apply.
tmnxEthRingPathTable	1.3.6.1.4.1.6527.3.1.2.72.1.3		not-accessible	The tmnxEthRingPathTable consists of the paths associated with the corresponding tmnxEthRingConfigEntry.
tmnxEthRingPathEntry	1.3.6.1.4.1.6527.3.1.2.72.1.3.1		not-accessible	The tmnxEthRingPathEntry contains information pertaining to an individual path associated with a tmnxEthRingConfigEntry. Rows in this table are created and destroyed using the tmnxEthRingPathRowStatus object.
TMN tmnxEthRingPathIndex	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.1	TmnxEthRingPathIndex	not-accessible	The tmnxEthRingPathIndex specifies the row index of the member.
ROW tmnxEthRingPathRowStatus	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.2	RowStatus	read-create	The tmnxEthRingPathRowStatus, along with tmnxEthRingPathIfIndex and tmnxEthRingPathIfRapsCcTag, control the creation and deletion of row entries in the tmnxEthRingPathTable.
TIM tmnxEthRingPathTimeStamp	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.3	TimeStamp	read-only	The value of tmnxEthRingPathTimeStamp indicates the time, since system startup, of the last change to this row.
NUM tmnxEthRingPathIfIndex	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.4	InterfaceIndexOrZero	read-create	The value of tmnxEthRingPathIfIndex specifies the member's port tmnxPortPortID associated with the tmnxEthRingConfigEntry. This object must be included in the same SNMP PDU as that of the tmnxEthRingPathRowStatus object for creation of the path. The absense of this object will result in a NO CREATION error. The tmnxEthRingPathIfIndex can not be changed; the row must be destroyed and re-created.
TMN tmnxEthRingPathIfRapsCcTag	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.5	TmnxEncapVal	read-create	The value of tmnxEthRingPathIfRapsCcTag specifies the member's encapsulation. This object must be included in the same SNMP PDU as that of the tmnxEthRingPathRowStatus object for creation of the path. The absense of this object will result in a NO CREATION ERROR Once specified, the tmnxEthRingPathIfRapsCcTag can not be changed; the row must be destroyed and re-created.
TIT tmnxEthRingPathDescription	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.6	TItemDescription	read-create	The value of tmnxEthRingPathDescription specifies a detailed description of the Ethernet Ring path.
TMN tmnxEthRingPathAdminStatus	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.7	TmnxAdminState	read-create	The value of tmnxEthRingPathAdminStatus specifies the administrative state of the path. 'outOfService (3)' specifies that the member will not partake in Ring Redundancy.
TMN tmnxEthRingPathOperStatus	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.8	TmnxOperState	read-only	The tmnxEthRingPathOperStatus indicates the operational state of of the path. The tmnxEthRingPathOperStatus supports the following two TmnxOperState values: inService (2) outOfService (3)
INT tmnxEthRingPathType	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.9	INTEGER	read-create	The value of tmnxEthRingPathType specifies the Ethernet Ring Node Path acts as an rplEnd or in a normal state. This is only configurable if tmnxEthRingRplNode is set to 'rplOwner (1)' or 'rplNeighbor (2)'.
INT tmnxEthRingPathFwdState	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.10	INTEGER	read-only	The value of tmnxEthRingPathFwdState indicates whether the Ethernet Ring Node Path blocks the transmission and reception of traffic on the ring port.
TIM tmnxEthRingPathFwdStateChgTime	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.11	TimeStamp	read-only	The value of tmnxEthRingPathFwdStateChgTime indicates the time, since system startup, that the Ethernet Ring Path last experienced a change in the forwarding state.
TMN tmnxEthRingPathRxApsPdu	1.3.6.1.4.1.6527.3.1.2.72.1.3.1.12	TmnxEthRingApsInfoType	read-only	The value of tmnxEthRingPathRxApsPdu indicates the contents of the R-APS PDU received on the Ethernet Ring path.
tmnxEthRingSAPConfigs	1.3.6.1.4.1.6527.3.1.2.72.1.4
tmnxEthRingSAPPathTable	1.3.6.1.4.1.6527.3.1.2.72.1.4.1		not-accessible	The tmnxEthRingSAPPathTable consists of the configuration for Ethernet Ring Group members associated to SAPs.
tmnxEthRingSAPPathEntry	1.3.6.1.4.1.6527.3.1.2.72.1.4.1.1		not-accessible	The tmnxEthRingSAPPathEntry contains the SAP information pertaining to an Ethernet Ring Group member. Entries in the tmnxEthRingSAPPathTable are created and destroyed by the system when the TIMETRA-SAP-MIB::sapEthRingIndex is set to a non-zero value during the creation of a row in the TIMETRA-SAP-MIB::sapBaseInfoTable.
U32 tmnxEthRingSAPPathIndex	1.3.6.1.4.1.6527.3.1.2.72.1.4.1.1.1	Unsigned32	read-only	The value of tmnxEthRingSAPPathIndex indicates the corresponding path index of the tmnxEthRingPathEntry for this row.
T/F tmnxEthRingSAPPathControlFlag	1.3.6.1.4.1.6527.3.1.2.72.1.4.1.1.2	TruthValue	read-only	The value of tmnxEthRingSAPPathControlFlag indicates whether or not this row corresponds to the control SAP of the tmnxEthRingConfigEntry.
tmnxEthRingCommandTable	1.3.6.1.4.1.6527.3.1.2.72.1.5		not-accessible	The tmnxEthRingCommandTable consists of the one-shot action commands that effect the state of the Ethernet Ring operation.
tmnxEthRingCommandEntry	1.3.6.1.4.1.6527.3.1.2.72.1.5.1		not-accessible	The tmnxEthRingCommandEntry contains the commands available to execute on an existing Ethernet Ring Group Path. Rows in this table are created and destroyed by the system.
INT tmnxEthRingCommandSwitch	1.3.6.1.4.1.6527.3.1.2.72.1.5.1.1	INTEGER	read-create	The value of tmnxEthRingCommandSwitch specifies the switch command to initiate on a path of an Ethernet Ring Group. When read, this object returns the last command written or 'noCmd (0)' if no command has been written to this Ethernet Ring Group path since initialization. The return of the last command written does not imply that this command is currently in effect. The request may be preempted by a higher priority local or remote request. In order to determine the current state of the group it is necessary to read the objects tmnxEthRingPathRxApsPdu and tmnxEthRingTxApsPdu. The value 'noCmd (0)' may not be used in a write command. The value 'clear (1)' clears all the switch commands listed below for the specified ring, regardless of the specified path. In addition, if tmnxEthRingRevertTime is a non-zero value (revertive mode) the active WTR (Wait To Restore) state is also cleared, or in the case of non-revertive mode, the command will trigger a reversion. The 'clear (1)' command is only valid if at least one path is configured and either: 1. a local Forced Switch or Manual Switch command is in effect, or 2. a local Ethernet Ring Node is an RPL Owner Node and top priority request is neither R-APS (FS) nor R-APS (MS). The value 'forceSwitch (2)' forces the specified path's tmnxEthRingPathFwdState to the 'blocked (1)' state. The value 'manualSwitch (3)' sets the specified path's tmnxEthRingPathFwdState to the 'blocked (1)' state in the absence of a failure or forceSwitch. An inconsistentValue error is returned, otherwise.
tmnxEthRingStatistics	1.3.6.1.4.1.6527.3.1.2.72.2
tmnxEthRingNotifyPrefix	1.3.6.1.4.1.6527.3.1.3.72
tmnxEthRingNotifications	1.3.6.1.4.1.6527.3.1.3.72.0
tmnxEthRingOprNotifications	1.3.6.1.4.1.6527.3.1.3.72.0.1
NTF tmnxEthRingPathFwdStateChange	1.3.6.1.4.1.6527.3.1.3.72.0.1.1			The tmnxEthRingPathFwdStateChange is generated when an Ethernet Ring Path changes its forwarding state (tmnxEthRingPathFwdState) from blocked to unblocked or from unblocked to blocked.
tmnxEthRingApsNotifications	1.3.6.1.4.1.6527.3.1.3.72.0.2
NTF tmnxEthRingApsPrvsnRaiseAlarm	1.3.6.1.4.1.6527.3.1.3.72.0.2.1			The tmnxEthRingApsPrvsnRaiseAlarm is generated when an Ethernet Ring provisioning mismatch is detected. A mismatch occurs when the RPL Owner Node receives one or more No Request R-APS message(s) with RPL Blocked status flag set (NR,RB) and a Node ID that differs from its own.
NTF tmnxEthRingApsPrvsnClearAlarm	1.3.6.1.4.1.6527.3.1.3.72.0.2.2			The tmnxEthRingApsPrvsnClearAlarm is generated when an Ethernet Ring provisioning mismatch is cleared.

RFC description

Manages Ethernet Ring components for Alcatel-Lucent SROS carrier-class routers.

Start monitoring Nokia/Alcatel-Lucent 7750 SR/7450 ESS metro Ethernet switch/router (Ethernet ring protection-switching status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TIMETRA-ETH-RING-MIB

What Is TIMETRA-ETH-RING-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description