SL-SONET-MIB

All MIBs › SL-SONET-MIB

Organization: Smartoptics AS

Last Updated: 2000-08-28

Description: MIB for SONET/SDH service management on SmartOptics SiteLight equipment, extending RFC 2558 with section, line, and path performance data and overhead configuration

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SL-SONET-MIB?

SL-SONET-MIB is a SmartOptics SiteLight proprietary MIB that extends the IETF SONET/SDH MIB (RFC 2558) with additional configuration and performance objects for SONET/SDH optical interfaces on SiteLight metro/optical transport equipment. It exposes configuration data (frame scrambling, DCC channel selection, overhead tunneling, compression) alongside performance and threshold data (signal-degrade and signal-failure thresholds, loss-of-pointer bitmasks, counter resets). Each SL-SONET-MIB OID such as slSonetConfigSdThreshold or slSonetConfigSfThreshold directly supports monitoring hardware/link status, since threshold-crossing on these objects and loss-of-pointer bitmask entries reveal optical transmission faults and degrading link quality on a SONET port. It explicitly builds on and extends RFC 2558, so standard SONET/SDH objects are expected to coexist with these vendor extensions. It is typically deployed on SmartOptics SiteLight optical transport/WDM equipment in metro and regional optical networks.

IPNetwork Monitor allows you to monitor SNMP objects defined in SL-SONET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SmartOptics SiteLight optical transport equipment
SONET/SDH network elements (metro/regional optical transport)

Monitoring Examples

slSonetConfigTable/slSonetConfigEntry expose per-port settings such as slSonetConfigFrameScramble, slSonetConfigType, and slSonetConfigDccSelection; an admin would check slSonetConfigSdThreshold and slSonetConfigSfThreshold to confirm degrade/failure alarm thresholds are set correctly for a given circuit. slSonetPortThresholdTrapEnable controls whether threshold-crossing traps fire, and slSonetLopBitmask reports loss-of-pointer framing errors on the signal. slSonetResetAllCounters lets an operator clear accumulated performance counters after maintenance work, while slSonetOverheadTunneling and slSonetCompression show whether those link features are currently enabled.

What Can Be Monitored

SONET signal degrade (SD) threshold
signal failure (SF) threshold
loss-of-pointer error bitmask
frame scramble configuration
DCC channel selection
overhead tunneling/compression state
threshold-crossing trap enablement

Imported Objects

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From PerfHist-TC-MIB

PerfCurrentCount
PerfIntervalCount
PerfTotalCount

From SL-NE-MIB

sitelight

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Gauge32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
slSonetMib	1.3.6.1.4.1.4515.1.6			This MIB module describes the SiteLight SONET Service. The mib contains the extensions required for the rfc2558.
slSonetConfig	1.3.6.1.4.1.4515.1.6.1
slSonetConfigTable	1.3.6.1.4.1.4515.1.6.1.1		not-accessible	The SONET/SDH configuration table. This table has objects for configuring sonet lines.
slSonetConfigEntry	1.3.6.1.4.1.4515.1.6.1.1.1		not-accessible	An entry in the table. There is an entry for each SONET line in the table. Entries are automatically created for an ifType value of sonet(39). 'ifAdminStatus' from the ifTable must be used to enable or disable a line. By default, the line state is down.
INT slSonetConfigFrameScramble	1.3.6.1.4.1.4515.1.6.1.1.1.1	INTEGER	read-write	This object is used to disable or enable the Scrambling option in SONET line. Please refer to GR-253-CORE for frame scrambling.
INT slSonetConfigType	1.3.6.1.4.1.4515.1.6.1.1.1.2	INTEGER	read-write	This object represents the configured line type for Trunks: sonetSts48c(5) - 1 x Sts48 (2.5GbTrunk) sonetSts192c(12) - 1 x Sts192 (10Gb Trunk) sonetStsOther(13) - for OC-n interfaces see slSonetFsTable.
INT slSonetConfigDccSelection	1.3.6.1.4.1.4515.1.6.1.1.1.3	INTEGER	read-write	This object selects the DCC type.
INT slSonetResetAllCounters	1.3.6.1.4.1.4515.1.6.1.1.1.4	INTEGER	read-write	Setting this variable to 1 will cause all of the counters (performance regsters) on this SONET interface to be initialized to zero (0).
INT slSonetPortThresholdTrapEnable	1.3.6.1.4.1.4515.1.6.1.1.1.5	INTEGER	read-write	This variable indicates whether threshold traps should be generated for this SONET interface.
INT slSonetConfigSdThreshold	1.3.6.1.4.1.4515.1.6.1.1.1.6	INTEGER	read-write	This object contains the Bit Error Rate threshold for Signal Degrade detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to -n where n is between 5 and 9 (read-write).
INT slSonetConfigSfThreshold	1.3.6.1.4.1.4515.1.6.1.1.1.7	INTEGER	read-write	This object contains the Bit Error Rate threshold for Signal Fault detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to the -n, where n is between 3 and 5. (read-write)
INT slSonetCompression	1.3.6.1.4.1.4515.1.6.1.1.1.9	INTEGER	read-write	This object applies only for trunk ports. It specifies if the packets should be compressed. 0 - Means no POS compression, 1 - Means POS compression with CRC-32. 2 - Means POS compression with CRC-16. Note that the two connected trunks should be configured to the same value. Note also that the BW calculation of the OC-n should be changed according to this value.
INT slSonetOverheadTunneling	1.3.6.1.4.1.4515.1.6.1.1.1.10	INTEGER	read-write	The section and line overhead tunneling configuration: none(0) - no tunneling support lineDcc(1) - line DCC tunneling k1k2(2) - line DCC + protection k byte full(3) - all transport overhead bytes are tunneled
C64 slSonetLopBitmask	1.3.6.1.4.1.4515.1.6.1.1.1.11	Counter64	read-only	The LOP status. Each bit of the bits represent the status of the LOP alarm in corresponding STS. For a path with more than a single STS, only the value of the first STS in the path is relevant. This object is relevant only for the OC-N cards and not for the Trunk. In the next future this object will be replaced with an object of a new table that shall describe the OC-N frame structure.
T/F slSonetTdmTrunk	1.3.6.1.4.1.4515.1.6.1.1.1.12	TruthValue	read-write	This object is applicable only to the OC-n ports. TRUE - means that the OC-n port is used as a TDM Trunk. FLASE - means normal OC-n port.
INT slSonetFsApply	1.3.6.1.4.1.4515.1.6.1.1.1.13	INTEGER	read-write	Writing to this object activate the slSonetFsTable setting. This allow the NMS to do many changes to the slSonetFsTable and then APPLY them at once. This prevent from going through unconsistent steps. This object always returns the value 0.
INT slSonetTxLte	1.3.6.1.4.1.4515.1.6.1.1.1.14	INTEGER	read-write	The SS bits to transmit (bits 5,6 in H1,H1*).
INT slSonetReceivedLte	1.3.6.1.4.1.4515.1.6.1.1.1.15	INTEGER	read-only	The detected LTE type, according to the received SS bits (bits 5,6 in H1,H1*).
INT slSonetResetPmThreshold	1.3.6.1.4.1.4515.1.6.1.1.1.16	INTEGER	read-write	Setting this variable to 1 will reset the PM threshold parameters to the factory defaults.
INT slSonetResetAlsParams	1.3.6.1.4.1.4515.1.6.1.1.1.17	INTEGER	read-write	Setting this variable to 1 will reset the ALS parameters to the factory defaults.
INT slSonetTransceiverType	1.3.6.1.4.1.4515.1.6.1.1.1.18	INTEGER	read-only	The tranceiver type.
INT slSonetTransceiverMedia	1.3.6.1.4.1.4515.1.6.1.1.1.19	INTEGER	read-only	The tranceiver media.
slSonetOh	1.3.6.1.4.1.4515.1.6.2
slSonetOhTrace	1.3.6.1.4.1.4515.1.6.2.1
slSonetTraceTable	1.3.6.1.4.1.4515.1.6.2.1.1		not-accessible	The SONET/SDH Trace table. This table contains objects for tracing the sonet section and path.
slSonetTraceEntry	1.3.6.1.4.1.4515.1.6.2.1.1.1		not-accessible	An entry in the trace table. Entries exist for active sonet interfaces. The objects in this table are used to verify continued connection between the two ends of the line.
INT slSonetTraceMode	1.3.6.1.4.1.4515.1.6.2.1.1.1.1	INTEGER	read-write	Determine the Trace Message Mode.
STR slSonetTraceToTransmit	1.3.6.1.4.1.4515.1.6.2.1.1.1.2	DisplayString	read-write	Sonet Trace To Transmit. This is string that is transmitted to perform Sonet trace diagnostics. The trace string is repetitively transmited so that a trace receiving terminal can verify its continued connection to the intended transmitter. The default value is a zero-length string. Unless this object is set to a non-zero length string, tracing will not be performed. The Agent is responsible to pad the end of the string with .
STR slSonetTraceToExpect	1.3.6.1.4.1.4515.1.6.2.1.1.1.3	DisplayString	read-write	Sonet Trace Massage To Expect. The receiving terminal verifies if the incoming string matches this string. The value of 'slSonetTraceFailure' indicates whether a trace mismatch occurred. The default value is a zero-length string. The Agent is responsible to pad the end of the string with .
T/F slSonetTraceFailure	1.3.6.1.4.1.4515.1.6.2.1.1.1.4	TruthValue	read-only	The value of this object is set to 'true' when Sonet Section received trace does not match the 'slSonetTraceToExpect'.
STR slSonetTraceReceived	1.3.6.1.4.1.4515.1.6.2.1.1.1.5	DisplayString	read-only	This object is used to view the Sonet Trace Message that is received by the receiving terminal. The Agent is responsible to pad the end of the string with .
slSonetOhSl	1.3.6.1.4.1.4515.1.6.2.2
slSonetSlTable	1.3.6.1.4.1.4515.1.6.2.2.1		not-accessible	The SONET/SDH Signal Label table. This table contains signal label for the sonet path.
slSonetSlEntry	1.3.6.1.4.1.4515.1.6.2.2.1.1		not-accessible	An entry in the SONET/SDH Signal Label table. The entries exist for active sonet lines. The objects in this table are used to verify continued connection between the two ends of the line.
SIG slSonetSlToTransmit	1.3.6.1.4.1.4515.1.6.2.2.1.1.2	SignalLabel	read-write	Sonet Signal Label To Transmit.
SIG slSonetSlToExpect	1.3.6.1.4.1.4515.1.6.2.2.1.1.3	SignalLabel	read-write	Sonet Signal Label To Expect.
T/F slSonetSlFailure	1.3.6.1.4.1.4515.1.6.2.2.1.1.4	TruthValue	read-only	The value of this object is set to 'true' when Sonet received signal label does not match the 'slSonetSlToExpect'.
INT slSonetSlReceived	1.3.6.1.4.1.4515.1.6.2.2.1.1.5	INTEGER	read-only	This object is used to view the Sonet Signal Label that is received by the receiving terminal.
slSonetOhTraps	1.3.6.1.4.1.4515.1.6.2.3
slSonetPos	1.3.6.1.4.1.4515.1.6.6
slSonetPosTable	1.3.6.1.4.1.4515.1.6.6.1		not-accessible	The POS PM Table.
slSonetPosEntry	1.3.6.1.4.1.4515.1.6.6.1.1		not-accessible	The entries exist for active Trunk sonet lines ifType = pos(171). The objects in this table are used to moitor the POS layer.
G32 slSonetPosFcs	1.3.6.1.4.1.4515.1.6.6.1.1.1	Gauge32	read-only	The Number of FCS Errors.
G32 slSonetPosAbort	1.3.6.1.4.1.4515.1.6.6.1.1.2	Gauge32	read-only	The Number of Aborted packets.
G32 slSonetPosMinViolation	1.3.6.1.4.1.4515.1.6.6.1.1.3	Gauge32	read-only	The Number of Minimum length violation packets.
G32 slSonetPosMaxViolation	1.3.6.1.4.1.4515.1.6.6.1.1.4	Gauge32	read-only	The Number of Maximum length violation packets.
G32 slSonetPosRxfifoDiscard	1.3.6.1.4.1.4515.1.6.6.1.1.5	Gauge32	read-only	The Number of packets discarded due to RXFIFO error.
C64 slSonetPosPacketReceived	1.3.6.1.4.1.4515.1.6.6.1.1.6	Counter64	read-only	The Number of packets received.
C64 slSonetPosPacketReceivedOk	1.3.6.1.4.1.4515.1.6.6.1.1.7	Counter64	read-only	The Number of error free packets.
slSonetAls	1.3.6.1.4.1.4515.1.6.7
slSonetAlsTable	1.3.6.1.4.1.4515.1.6.7.1		not-accessible	The ALS configuration Table.
slSonetAlsEntry	1.3.6.1.4.1.4515.1.6.7.1.1		not-accessible	The entries exist for active sonet lines ifType = sonet(39). The objects in this table are used to configure the ALS algorithm.
INT slSonetAlsMode	1.3.6.1.4.1.4515.1.6.7.1.1.1	INTEGER	read-write	Enable/Disable the ALS algorithm. Note that the if the Laser Admin Status is 'down' the ALS mechanism is not operational.
INT slSonetLosDeclareTime	1.3.6.1.4.1.4515.1.6.7.1.1.2	INTEGER	read-write	Time to declare optical LOS present or clear: 550 +- 50 msec.
INT slSonetTestPulseTime	1.3.6.1.4.1.4515.1.6.7.1.1.3	INTEGER	read-write	Manual restart for test Pulse time (in manual restart) - 90+-10 sec.
INT slSonetManualPulseTime	1.3.6.1.4.1.4515.1.6.7.1.1.4	INTEGER	read-write	Manual restart Pulse time (in manual mode) - 2+-0.25 sec.
INT slSonetAutomaticPulseTime	1.3.6.1.4.1.4515.1.6.7.1.1.5	INTEGER	read-write	Automatic restart Pulse time (in automatic mode) - 2+-0.25 sec.
INT slSonetAutomaticDelayTime	1.3.6.1.4.1.4515.1.6.7.1.1.6	INTEGER	read-write	In Automatic mode. The delay between two laser re-activations.
INT slSonetLaserTestActivate	1.3.6.1.4.1.4515.1.6.7.1.1.7	INTEGER	read-write	Activate the laser for test operation.
INT slSonetLaserManualActivate	1.3.6.1.4.1.4515.1.6.7.1.1.8	INTEGER	read-write	Activate the laser manual operation.
slSonetFs	1.3.6.1.4.1.4515.1.6.8
slSonetFsTable	1.3.6.1.4.1.4515.1.6.8.1		not-accessible	The frame structure configuration Table. In order to define a new path the NMS should create and configure an entry in this table. The table is also used to monitor the status of the LOP alarm per path.
slSonetFsEntry	1.3.6.1.4.1.4515.1.6.8.1.1		not-accessible	The entries exist for sonet paths ifType = sonet(39). The objects in this table are used to configure the frame structure. Each OC-N line interface shall maintain a static table with number of lines equal to the N. Initially the table will be initialized to STS-Nc.
NUM slSonetFsIfIndex	1.3.6.1.4.1.4515.1.6.8.1.1.1	InterfaceIndex	read-only	The interface index.
INT slSonetFsSts	1.3.6.1.4.1.4515.1.6.8.1.1.2	INTEGER	read-only	The number of the first STS in the path. Note that no all values are legal because there is no support for combus with mixed structure
INT slSonetFsWidth	1.3.6.1.4.1.4515.1.6.8.1.1.3	INTEGER	read-write	The number STS's in the path. The width is only valid for the first STS in the path. The other STSs of the path will have width=0.
T/F slSonetFsFullPathTermination	1.3.6.1.4.1.4515.1.6.8.1.1.4	TruthValue	read-write	FALSE - means partial path termination (only LOP alarm). TRUE - include full support for path Alarms and PM counters.
INT slSonetFsGranularity	1.3.6.1.4.1.4515.1.6.8.1.1.5	INTEGER	read-write	This value is set by the NMS according to the configured frame structure. Each VC-3 that is mapped to AUG-1 via VC-4 should have the value vc4(1). Otherwise the value should be vc3(2).
slSonetTraps	1.3.6.1.4.1.4515.1.6.11
NTF slSonetFsTableChange	1.3.6.1.4.1.4515.1.6.11.1			A slSonetFsTableChange trap is sent when the content of the slSonetFsTable is changed. This trap may be used by the NMS to identify the removal of path interfaces, or addition of new path interfaces

RFC description

SONET/SDH line card management MIB for monitoring synchronous optical network interfaces.

Start monitoring SmartOptics SiteLight optical transport equipment, SONET/SDH network elements (RFC 2558 extension config/thresholds) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SL-SONET-MIB

What Is SL-SONET-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description