TELDAT-CFG-INTERF-IEC101GW-MIB

All MIBs › TELDAT-CFG-INTERF-IEC101GW-MIB

Category: IP Services and Protocols, SCADA and Industrial Protocols

Description: Manages Teldat router IEC 101 SCADA gateway interface configuration and serial link settings.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELDAT-CFG-INTERF-IEC101GW-MIB?

TELDAT-CFG-INTERF-IEC101GW-MIB is a vendor MIB from Teldat, a Spanish manufacturer of enterprise/industrial routers, covering configuration of the IEC 60870-5-101 protocol gateway interface on its router platforms. It exposes configuration objects for the serial link parameters and protocol settings that let a Teldat router act as a gateway translating IEC 101 SCADA traffic for utility/industrial control networks. Its monitoring relevance is primarily configuration and interface-state oriented: confirming the serial link parameters and gateway operating mode are correctly set, since a misconfigured baud rate, address, or protocol parameter would break SCADA polling between a remote terminal unit and its control center. As a gateway-protocol MIB it depends conceptually on the IEC 60870-5-101/104 standards it bridges between, though it doesn't appear to import other SNMP MIBs directly. It is deployed on Teldat routers used as protocol gateways in electrical utility, water, or other SCADA/industrial-control WAN deployments, where TELDAT-CFG-INTERF-IEC101GW-MIB SNMP monitoring verifies the gateway's serial-link configuration stays correct.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELDAT-CFG-INTERF-IEC101GW-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teldat routers configured as IEC 60870-5-101 SCADA protocol gateways

Monitoring Examples

No concrete object or table names were captured from this MIB's parsed source. In practice an operator would poll the gateway's serial-interface configuration objects (e.g., baud rate, station address, protocol mode) to confirm the IEC 101 link is configured as expected, with a mismatch or link-down condition explaining a SCADA master losing contact with a remote substation.

What Can Be Monitored

IEC 101 serial link configuration
gateway protocol mode/settings
interface operational parameters

Imported Objects

From RFC-1212

OBJECT-TYPE

From TELDAT-SW-STRUCTURE-MIB

telProdNpConfInterface

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
telProdNpConfInterfIec101GW	1.3.6.1.4.1.2007.4.1.1.4.16
telProdNpIec101GWTable	1.3.6.1.4.1.2007.4.1.1.4.16.1		not-accessible	Table of global configuration for IEC101 GW interfaces. Each row represents an interface
telProdNpIec101GWEntry	1.3.6.1.4.1.2007.4.1.1.4.16.1.1		not-accessible	A base list of objects that are configuration information about an IEC101 GW interface. The index is the number of the interface.
INT telProdNpIec101GWIfcIndex	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.1	INTEGER	read-only	IEC101-GW interface index. It is the index table.
INT telProdNpIec101GWIfcAsduCAddr	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.2	INTEGER	read-write	Set RTU ASDU common Adress for no multilink mode.
INT telProdNpIec101GWIfcBaudRate	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.3	INTEGER	read-write	Set baud reate for serial interface.
INT telProdNpIec101GWIfcLinkAddr	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.4	INTEGER	read-write	Set RTU Link Adress for no multilink mode.
INT telProdNpIec101GWIfcLinkAddrSz	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.5	INTEGER	read-write	Set Link Adress field size.
INT telProdNpIec101GWIfcLongResp	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.6	INTEGER	read-write	Enable sends long frame responses to RTU's.
INT telProdNpIec101GWIfcMultilink	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.7	INTEGER	read-write	Enable RTU's multilink mode.
INT telProdNpIec101GWIfcBuffNum	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.8	INTEGER	read-write	Configure number of IEC-101 transmission buffers.
INT telProdNpIec101GWIfcOrigAddr	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.9	INTEGER	read-write	Configure IEC-101 Originator Address.
INT telProdNpIec101GWIfcRetransMax	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.10	INTEGER	read-write	Configure maximum number of IEC-101 messages retransmissions.
INT telProdNpIec101GWIfcRetransTime	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.11	INTEGER	read-write	Configure time for IEC-101 messages retransmissions. Time in milliseconds
INT telProdNpIec101GWIfcRxTimeout	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.12	INTEGER	read-write	Configure input frame timeout. Time in milliseconds
INT telProdNpIec101GWIfcSyncTime	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.13	INTEGER	read-write	Configure period time to sent IEC-101 Synchronization message to RTU. Time in minutes
INT telProdNpIec101GWIfcTestTime	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.14	INTEGER	read-write	Configure period time to sent IEC-101 Link Test message to RTU. Time in seconds
INT telProdNpIec101GWIfcTestType	1.3.6.1.4.1.2007.4.1.1.4.16.1.1.15	INTEGER	read-write	Configure type of IEC-101 Link Test message to send to RTU. 0 Don't send message, 1 Send Test message, 2 Send Status message.
telProdNpIec101GWIfcRtuTable	1.3.6.1.4.1.2007.4.1.1.4.16.2		not-accessible	Table of RTU Link Address configuration for IEC101 GW interfaces. There are two table indexes: the interface and the RTU index.
telProdNpIec101GWIfcRtuEntry	1.3.6.1.4.1.2007.4.1.1.4.16.2.1		not-accessible	Each entry contains an RTU link address. Each entry consist on an interfece index and an RTU index.
INT telProdNpIec101GWIfcRtuIfcIndex	1.3.6.1.4.1.2007.4.1.1.4.16.2.1.1	INTEGER	read-only	IEC101-GW interface index. It is the index table.
INT telProdNpIec101GWIfcRtuIndex	1.3.6.1.4.1.2007.4.1.1.4.16.2.1.2	INTEGER	read-only	RTU table index.
INT telProdNpIec101GWIfcRtuStatus	1.3.6.1.4.1.2007.4.1.1.4.16.2.1.3	INTEGER	read-write	Table control variable. Set to 1 does nothing. Set to 2 adds a new row (RTU link address) in the table with default value(65534) and returns 2. If it already exists, then it returns error. It must be added immediately after the last index. To greate a new row RTU address 65534 must not exist. After greate you must modify RTU address. Set to 3 deletes all table fields corresponding to that Agent, and returns 3. Get returns 1 if the control exists.
INT telProdNpIec101GWIfcRtuAddress	1.3.6.1.4.1.2007.4.1.1.4.16.2.1.4	INTEGER	read-write	Set link address for a RTU in multilink mode. RTU link address can not be repeated. If address already exists, then it returns error.

RFC description

Manages configuration of IEC-101 gateway interfaces on Teldat networking devices, including serial communication parameters and protocol settings.

Start monitoring Teldat router configured as IEC 60870-5-101 SCADA protocol gateway (serial-link config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELDAT-CFG-INTERF-IEC101GW-MIB

What Is TELDAT-CFG-INTERF-IEC101GW-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description