TELDAT-TRAP-I101-MIB

All MIBs › TELDAT-TRAP-I101-MIB

Organization: Teldat, S.A.

Last Updated: 2014-01-20

Category: SCADA and Industrial Protocols, Teldat Router Management, Teldat Trap Notifications

Description: Defines Teldat router I101 (IEC-101 SCADA) event trap notifications.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELDAT-TRAP-I101-MIB?

TELDAT-TRAP-I101-MIB is a Teldat proprietary, notification-only SNMP MIB that defines the trap varbinds emitted by the router's I101 (IEC 60870-5-101) event subsystem, relevant when a Teldat router is used as a gateway or protocol converter in a SCADA/utility telemetry deployment. It groups numbered event definitions (i1011 through i1016, under i101EventsGroup/i101Notifications) carrying byte counts, serial address and interface identifiers, cause codes, and message-type values specific to the IEC-101 serial telemetry protocol. Operationally it is a fault/event monitor for the SCADA communication link: it lets a management station learn asynchronously about byte-transfer volume, serial-link cause-of-transmission codes, and message-type events on the IEC-101 channel, which is critical for detecting a stalled or misbehaving RTU/master link in industrial or utility telemetry, where communication-layer faults can directly affect grid or plant monitoring. As with Teldat's other TRAP-* modules it depends on the standard SNMPv2-SMI/SNMPv2-TC notification conventions and Teldat's private enterprise OID tree, layered on top of the IEC 60870-5-101 standard it interoperates with. It is deployed on Teldat routers serving as SCADA/RTU gateways in utility, energy, or industrial-control network deployments, where engineers can download the TELDAT-TRAP-I101-MIB file to load into their trap receiver or MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELDAT-TRAP-I101-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teldat router used as SCADA/RTU gateway

Monitoring Examples

This module defines only notification objects and their varbinds rather than a polled counter table, so there is no GET-based monitoring scenario; it is trap-only. An SNMP trap receiver would inspect i1012_serrial_address and i1012_interface together with i1012_bytes_number to see traffic volume on a specific IEC-101 serial link, and i1013_cause on i1013_interface to determine the cause-of-transmission code behind a reported communication fault.

What Can Be Monitored

IEC 60870-5-101 SCADA link byte-transfer events
SCADA serial-link cause-of-transmission/message-type events

Imported Objects

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

From TELDAT-MIB

telEventTraps

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
i101TrapsMIB	1.3.6.1.4.1.2007.1.4.229			This Module Information Base file is defined for managing received SNMP notifications generated by the I101 event subsystem.
i101EventsGroup	1.3.6.1.4.1.2007.1.4.229.1
i101EventObjects1	1.3.6.1.4.1.2007.1.4.229.1.1			Event I101.1 Data has been received from Serial Terminal.
I32 i1011BytesNumber	1.3.6.1.4.1.2007.1.4.229.1.1.1	Integer32	accessible-for-notify	Parameter 'bytesNumber' in event I101.1
STR i1011Interface	1.3.6.1.4.1.2007.1.4.229.1.1.2	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.1
i101EventObjects2	1.3.6.1.4.1.2007.1.4.229.1.2			Event I101.2 One OK Message has been received from Serial Terminal.
STR i1012Coment	1.3.6.1.4.1.2007.1.4.229.1.2.1	DisplayString	accessible-for-notify	Parameter 'coment' in event I101.2
I32 i1012SerrialAddress	1.3.6.1.4.1.2007.1.4.229.1.2.2	Integer32	accessible-for-notify	Parameter 'serrialAddress' in event I101.2
I32 i1012BytesNumber	1.3.6.1.4.1.2007.1.4.229.1.2.3	Integer32	accessible-for-notify	Parameter 'bytesNumber' in event I101.2
STR i1012Interface	1.3.6.1.4.1.2007.1.4.229.1.2.4	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.2
i101EventObjects3	1.3.6.1.4.1.2007.1.4.229.1.3			Event I101.3 One Bad Message has been received from Serial Terminal.
STR i1013Cause	1.3.6.1.4.1.2007.1.4.229.1.3.1	DisplayString	accessible-for-notify	Parameter 'cause' in event I101.3
STR i1013Interface	1.3.6.1.4.1.2007.1.4.229.1.3.2	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.3
i101EventObjects4	1.3.6.1.4.1.2007.1.4.229.1.4			Event I101.4 A message with LRC/CRC error has been received from Serial Terminal.
STR i1014Interface	1.3.6.1.4.1.2007.1.4.229.1.4.1	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.4
i101EventObjects5	1.3.6.1.4.1.2007.1.4.229.1.5			Event I101.5 A Message has been transmitted to Serial Terminal.
I32 i1015Bytes	1.3.6.1.4.1.2007.1.4.229.1.5.1	Integer32	accessible-for-notify	Parameter 'bytes' in event I101.5
STR i1015Interface	1.3.6.1.4.1.2007.1.4.229.1.5.2	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.5
i101EventObjects6	1.3.6.1.4.1.2007.1.4.229.1.6			Event I101.6 A change ON/OFF has been detected in Serial Control Signal Input.
STR i1016MessageType	1.3.6.1.4.1.2007.1.4.229.1.6.1	DisplayString	accessible-for-notify	Parameter 'messageType' in event I101.6
STR i1016Interface	1.3.6.1.4.1.2007.1.4.229.1.6.2	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.6
i101EventObjects7	1.3.6.1.4.1.2007.1.4.229.1.7			Event I101.7 A change ON/OFF has been make in Serial Control Signal Output.
STR i1017MessageType	1.3.6.1.4.1.2007.1.4.229.1.7.1	DisplayString	accessible-for-notify	Parameter 'messageType' in event I101.7
STR i1017Interface	1.3.6.1.4.1.2007.1.4.229.1.7.2	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.7
i101EventObjects8	1.3.6.1.4.1.2007.1.4.229.1.8			Event I101.8 Data error from Serial Terminal has been received.
STR i1018MessageType	1.3.6.1.4.1.2007.1.4.229.1.8.1	DisplayString	accessible-for-notify	Parameter 'messageType' in event I101.8
STR i1018Interface	1.3.6.1.4.1.2007.1.4.229.1.8.2	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.8
i101EventObjects9	1.3.6.1.4.1.2007.1.4.229.1.9			Event I101.9 Detailed Data send to serial interface.
STR i1019Interface	1.3.6.1.4.1.2007.1.4.229.1.9.1	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.9
I32 i1019SerialAddress	1.3.6.1.4.1.2007.1.4.229.1.9.2	Integer32	accessible-for-notify	Parameter 'serialAddress' in event I101.9
I32 i1019Lenght	1.3.6.1.4.1.2007.1.4.229.1.9.3	Integer32	accessible-for-notify	Parameter 'lenght' in event I101.9
STR i1019HexData	1.3.6.1.4.1.2007.1.4.229.1.9.4	DisplayString	accessible-for-notify	Parameter 'hexData' in event I101.9
i101EventObjects10	1.3.6.1.4.1.2007.1.4.229.1.10			Event I101.10 Detailed Data received from serial interface.
STR i10110Interface	1.3.6.1.4.1.2007.1.4.229.1.10.1	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.10
I32 i10110SerialAddress	1.3.6.1.4.1.2007.1.4.229.1.10.2	Integer32	accessible-for-notify	Parameter 'serialAddress' in event I101.10
I32 i10110Lenght	1.3.6.1.4.1.2007.1.4.229.1.10.3	Integer32	accessible-for-notify	Parameter 'lenght' in event I101.10
STR i10110HexData	1.3.6.1.4.1.2007.1.4.229.1.10.4	DisplayString	accessible-for-notify	Parameter 'hexData' in event I101.10
i101EventObjects11	1.3.6.1.4.1.2007.1.4.229.1.11			Event I101.11 A status change has occurred on RTU.
STR i10111Rtu	1.3.6.1.4.1.2007.1.4.229.1.11.1	DisplayString	accessible-for-notify	Parameter 'rtu' in event I101.11
STR i10111Statsu	1.3.6.1.4.1.2007.1.4.229.1.11.2	DisplayString	accessible-for-notify	Parameter 'statsu' in event I101.11
i101EventObjects12	1.3.6.1.4.1.2007.1.4.229.1.12			Event I101.12 Tx data discarted due interface is in down state.
STR i10112Interface	1.3.6.1.4.1.2007.1.4.229.1.12.1	DisplayString	accessible-for-notify	Parameter 'interface' in event I101.12
i101Notifications	1.3.6.1.4.1.2007.1.4.229.2
i101NotificationsPrefix	1.3.6.1.4.1.2007.1.4.229.2.0
NTF i101Notification1	1.3.6.1.4.1.2007.1.4.229.2.0.1			Notification of Event I101.1 Message: 'Rx Data from Serial Terminal $1 bytes, interface $2' Parameters list: $1: i1011BytesNumber $2: i1011Interface Data has been received from Serial Terminal.
NTF i101Notification2	1.3.6.1.4.1.2007.1.4.229.2.0.2			Notification of Event I101.2 Message: 'Rx Message $1 from Serial Terminal address $2, $3 bytes, interface $4' Parameters list: $1: i1012Coment $2: i1012SerrialAddress $3: i1012BytesNumber $4: i1012Interface One OK Message has been received from Serial Terminal.
NTF i101Notification3	1.3.6.1.4.1.2007.1.4.229.2.0.3			Notification of Event I101.3 Message: 'Rx Bad Message from Serial Terminal ($1), interface $2' Parameters list: $1: i1013Cause $2: i1013Interface One Bad Message has been received from Serial Terminal.
NTF i101Notification4	1.3.6.1.4.1.2007.1.4.229.2.0.4			Notification of Event I101.4 Message: 'A block with LRC/CRC error has been received from Serial Terminal, interface $1' Parameters list: $1: i1014Interface A message with LRC/CRC error has been received from Serial Terminal.
NTF i101Notification5	1.3.6.1.4.1.2007.1.4.229.2.0.5			Notification of Event I101.5 Message: 'Tx Message to Serial Terminal, $1 bytes interface $2' Parameters list: $1: i1015Bytes $2: i1015Interface A Message has been transmitted to Serial Terminal.
NTF i101Notification6	1.3.6.1.4.1.2007.1.4.229.2.0.6			Notification of Event I101.6 Message: 'Serial Control Signal Imput CD change to $1, interface $2' Parameters list: $1: i1016MessageType $2: i1016Interface A change ON/OFF has been detected in Serial Control Signal Input.
NTF i101Notification7	1.3.6.1.4.1.2007.1.4.229.2.0.7			Notification of Event I101.7 Message: 'Serial Control signal Output DTR change to $1, interface $2' Parameters list: $1: i1017MessageType $2: i1017Interface A change ON/OFF has been make in Serial Control Signal Output.
NTF i101Notification8	1.3.6.1.4.1.2007.1.4.229.2.0.8			Notification of Event I101.8 Message: 'Data ERROR from Serial Terminal has been received type: $1. Interface $2' Parameters list: $1: i1018MessageType $2: i1018Interface Data error from Serial Terminal has been received.
NTF i101Notification9	1.3.6.1.4.1.2007.1.4.229.2.0.9			Notification of Event I101.9 Message: 'Data transmitted to serial interface $1 (addr:$2,$3 bytes):$4' Parameters list: $1: i1019Interface $2: i1019SerialAddress $3: i1019Lenght $4: i1019HexData Detailed Data send to serial interface.
NTF i101Notification10	1.3.6.1.4.1.2007.1.4.229.2.0.10			Notification of Event I101.10 Message: 'Data received from serial interface $1 (addr:$2,$3 bytes):$4' Parameters list: $1: i10110Interface $2: i10110SerialAddress $3: i10110Lenght $4: i10110HexData Detailed Data received from serial interface.
NTF i101Notification11	1.3.6.1.4.1.2007.1.4.229.2.0.11			Notification of Event I101.11 Message: 'RTU $1 link status change to $2' Parameters list: $1: i10111Rtu $2: i10111Statsu A status change has occurred on RTU.
NTF i101Notification12	1.3.6.1.4.1.2007.1.4.229.2.0.12			Notification of Event I101.12 Message: 'Data transmitted is discarted since interface $1 is down' Parameters list: $1: i10112Interface Tx data discarted due interface is in down state.

RFC description

SNMP notification events for IEC-101 protocol data reception and message confirmation.

Start monitoring Teldat router used as SCADA/RTU gateway, IEC 60870-5-101 (serial telemetry event traps) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELDAT-TRAP-I101-MIB

What Is TELDAT-TRAP-I101-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description