All MIBs › SONET-MIB
Organization: IETF AToM MIB Working Group
Last Updated: 2003-08-11
Category: Network Interfaces
Description: Defines managed objects for managing SONET/SDH interfaces, including line, section, and path-level configuration and performance monitoring.
IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring SONET-MIB with a free 30-day trial of IPNetwork Monitor.
What Is SONET-MIB?
SONET-MIB is an IETF standards-based module (RFC 3592) for managing SONET/SDH optical transmission interfaces, covering the section, line, and path layers of the SONET/SDH hierarchy. It exposes both configuration objects (interface type, framing mode) and performance/fault objects such as line/section/path current and interval performance-monitoring counters and alarm/defect indications. In monitoring terms it tracks the hardware/transmission health of SONET/SDH links, revealing error-rate counters, loss-of-signal or loss-of-frame conditions, and other physical-layer fault indications rather than general compute resources like CPU or memory. It builds on and is used alongside the IETF IF-MIB, since SONET interfaces register as entries in the standard interfaces table. Effective SONET-MIB SNMP monitoring is deployed on SONET/SDH transport equipment and router/switch line cards in carrier and enterprise optical transport networks.
IPNetwork Monitor allows you to monitor SNMP objects defined in SONET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- vendor-neutral, standards-based MIB, not tied to a specific manufacturer — applies to SONET/SDH transport equipment and optical interface line cards
Monitoring Examples
An operator would poll the SONET section- and line-current performance tables for error-second and severely-errored-second counts, and check the medium table for configured line type. A rising count of coding violations or an active loss-of-signal defect flag in these tables would indicate a degrading or failed optical link. Because no concrete sample object names were supplied for this module, table names are given generically based on the well-documented RFC 3592 structure rather than exact source text.
What Can Be Monitored
- SONET section/line/path error counters
- loss-of-signal/loss-of-frame defects
- interface framing configuration
- performance-monitoring interval statistics
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
From PerfHist-TC-MIB
| PerfCurrentCount | |
| PerfIntervalCount |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| transmission |
From SNMPv2-TC
| DisplayString | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| sonetCompliance | 1.3.6.1.2.1.10.39.4.2.1 | The compliance statement for SONET/SDH interfaces. | ||
| sonetCompliance2 | 1.3.6.1.2.1.10.39.4.2.2 | The compliance statement for SONET/SDH interfaces. | ||
| sonetCompliances | 1.3.6.1.2.1.10.39.4.2 | |||
| sonetConformance | 1.3.6.1.2.1.10.39.4 | |||
| sonetFarEndLine | 1.3.6.1.2.1.10.39.1.4 | |||
| PER sonetFarEndLineCurrentCVs | 1.3.6.1.2.1.10.39.1.4.1.1.3 | PerfCurrentCount | read-only | The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval. |
| sonetFarEndLineCurrentEntry | 1.3.6.1.2.1.10.39.1.4.1.1 | not-accessible | An entry in the SONET/SDH Far End Line Current table. | |
| PER sonetFarEndLineCurrentESs | 1.3.6.1.2.1.10.39.1.4.1.1.1 | PerfCurrentCount | read-only | The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval. |
| PER sonetFarEndLineCurrentSESs | 1.3.6.1.2.1.10.39.1.4.1.1.2 | PerfCurrentCount | read-only | The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval. |
| sonetFarEndLineCurrentTable | 1.3.6.1.2.1.10.39.1.4.1 | not-accessible | The SONET/SDH Far End Line Current table. | |
| PER sonetFarEndLineCurrentUASs | 1.3.6.1.2.1.10.39.1.4.1.1.4 | PerfCurrentCount | read-only | The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Medium/Section/Line interface in the current 15 minute interval. |
| NUM sonetFarEndLineIntervalCVs | 1.3.6.1.2.1.10.39.1.4.2.1.4 | PerfIntervalCount | read-only | The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours. |
| sonetFarEndLineIntervalEntry | 1.3.6.1.2.1.10.39.1.4.2.1 | not-accessible | An entry in the SONET/SDH Far End Line Interval table. | |
| NUM sonetFarEndLineIntervalESs | 1.3.6.1.2.1.10.39.1.4.2.1.2 | PerfIntervalCount | read-only | The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours. |
| I32 sonetFarEndLineIntervalNumber | 1.3.6.1.2.1.10.39.1.4.2.1.1 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM sonetFarEndLineIntervalSESs | 1.3.6.1.2.1.10.39.1.4.2.1.3 | PerfIntervalCount | read-only | The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours. |
| sonetFarEndLineIntervalTable | 1.3.6.1.2.1.10.39.1.4.2 | not-accessible | The SONET/SDH Far End Line Interval table. | |
| NUM sonetFarEndLineIntervalUASs | 1.3.6.1.2.1.10.39.1.4.2.1.5 | PerfIntervalCount | read-only | The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Line interface in a particular 15-minute interval in the past 24 hours. |
| T/F sonetFarEndLineIntervalValidData | 1.3.6.1.2.1.10.39.1.4.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| sonetFarEndLineStuff | 1.3.6.1.2.1.10.39.4.1.4 | A collection of objects providing information specific to SONET/SDH Line interfaces, and maintaining Line Far End information. | ||
| sonetFarEndLineStuff2 | 1.3.6.1.2.1.10.39.4.1.14 | A collection of objects providing information specific to SONET/SDH Line interfaces, and maintaining Line Far End information. | ||
| sonetFarEndPath | 1.3.6.1.2.1.10.39.2.2 | |||
| PER sonetFarEndPathCurrentCVs | 1.3.6.1.2.1.10.39.2.2.1.1.3 | PerfCurrentCount | read-only | The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Path interface in the current 15 minute interval. |
| sonetFarEndPathCurrentEntry | 1.3.6.1.2.1.10.39.2.2.1.1 | not-accessible | An entry in the SONET/SDH Far End Path Current table. | |
| PER sonetFarEndPathCurrentESs | 1.3.6.1.2.1.10.39.2.2.1.1.1 | PerfCurrentCount | read-only | The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval. |
| PER sonetFarEndPathCurrentSESs | 1.3.6.1.2.1.10.39.2.2.1.1.2 | PerfCurrentCount | read-only | The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Path interface in the current 15 minute interval. |
| sonetFarEndPathCurrentTable | 1.3.6.1.2.1.10.39.2.2.1 | not-accessible | The SONET/SDH Far End Path Current table. | |
| PER sonetFarEndPathCurrentUASs | 1.3.6.1.2.1.10.39.2.2.1.1.4 | PerfCurrentCount | read-only | The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Path interface in the current 15 minute interval. |
| NUM sonetFarEndPathIntervalCVs | 1.3.6.1.2.1.10.39.2.2.2.1.4 | PerfIntervalCount | read-only | The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours. |
| sonetFarEndPathIntervalEntry | 1.3.6.1.2.1.10.39.2.2.2.1 | not-accessible | An entry in the SONET/SDH Far End Path Interval table. | |
| NUM sonetFarEndPathIntervalESs | 1.3.6.1.2.1.10.39.2.2.2.1.2 | PerfIntervalCount | read-only | The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours. |
| I32 sonetFarEndPathIntervalNumber | 1.3.6.1.2.1.10.39.2.2.2.1.1 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM sonetFarEndPathIntervalSESs | 1.3.6.1.2.1.10.39.2.2.2.1.3 | PerfIntervalCount | read-only | The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours. |
| sonetFarEndPathIntervalTable | 1.3.6.1.2.1.10.39.2.2.2 | not-accessible | The SONET/SDH Far End Path Interval table. | |
| NUM sonetFarEndPathIntervalUASs | 1.3.6.1.2.1.10.39.2.2.2.1.5 | PerfIntervalCount | read-only | The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH Path interface in a particular 15-minute interval in the past 24 hours. |
| T/F sonetFarEndPathIntervalValidData | 1.3.6.1.2.1.10.39.2.2.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| sonetFarEndPathStuff | 1.3.6.1.2.1.10.39.4.1.6 | A collection of objects providing information specific to SONET/SDH Path interfaces, and maintaining Path Far End information. | ||
| sonetFarEndPathStuff2 | 1.3.6.1.2.1.10.39.4.1.15 | A collection of objects providing information specific to SONET/SDH Path interfaces, and maintaining Path Far End information. | ||
| sonetFarEndVT | 1.3.6.1.2.1.10.39.3.2 | |||
| PER sonetFarEndVTCurrentCVs | 1.3.6.1.2.1.10.39.3.2.1.1.3 | PerfCurrentCount | read-only | The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH VT interface in the current 15 minute interval. |
| sonetFarEndVTCurrentEntry | 1.3.6.1.2.1.10.39.3.2.1.1 | not-accessible | An entry in the SONET/SDH Far End VT Current table. | |
| PER sonetFarEndVTCurrentESs | 1.3.6.1.2.1.10.39.3.2.1.1.1 | PerfCurrentCount | read-only | The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH interface in the current 15 minute interval. |
| PER sonetFarEndVTCurrentSESs | 1.3.6.1.2.1.10.39.3.2.1.1.2 | PerfCurrentCount | read-only | The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH VT interface in the current 15 minute interval. |
| sonetFarEndVTCurrentTable | 1.3.6.1.2.1.10.39.3.2.1 | not-accessible | The SONET/SDH Far End VT Current table. | |
| PER sonetFarEndVTCurrentUASs | 1.3.6.1.2.1.10.39.3.2.1.1.4 | PerfCurrentCount | read-only | The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH VT interface in the current 15 minute interval. |
| NUM sonetFarEndVTIntervalCVs | 1.3.6.1.2.1.10.39.3.2.2.1.4 | PerfIntervalCount | read-only | The counter associated with the number of Far End Coding Violations reported via the far end block error count encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours. |
| sonetFarEndVTIntervalEntry | 1.3.6.1.2.1.10.39.3.2.2.1 | not-accessible | An entry in the SONET/SDH Far End VT Interval table. | |
| NUM sonetFarEndVTIntervalESs | 1.3.6.1.2.1.10.39.3.2.2.1.2 | PerfIntervalCount | read-only | The counter associated with the number of Far End Errored Seconds encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours. |
| I32 sonetFarEndVTIntervalNumber | 1.3.6.1.2.1.10.39.3.2.2.1.1 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM sonetFarEndVTIntervalSESs | 1.3.6.1.2.1.10.39.3.2.2.1.3 | PerfIntervalCount | read-only | The counter associated with the number of Far End Severely Errored Seconds encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours. |
| sonetFarEndVTIntervalTable | 1.3.6.1.2.1.10.39.3.2.2 | not-accessible | The SONET/SDH Far End VT Interval table. | |
| NUM sonetFarEndVTIntervalUASs | 1.3.6.1.2.1.10.39.3.2.2.1.5 | PerfIntervalCount | read-only | The counter associated with the number of Far End Unavailable Seconds encountered by a SONET/SDH VT interface in a particular 15-minute interval in the past 24 hours. |
| T/F sonetFarEndVTIntervalValidData | 1.3.6.1.2.1.10.39.3.2.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| sonetFarEndVTStuff | 1.3.6.1.2.1.10.39.4.1.8 | A collection of objects providing information specific to SONET/SDH VT interfaces, and maintaining VT Far End information. | ||
| sonetFarEndVTStuff2 | 1.3.6.1.2.1.10.39.4.1.16 | A collection of objects providing information specific to SONET/SDH VT interfaces, and maintaining VT Far End information. | ||
| sonetGroups | 1.3.6.1.2.1.10.39.4.1 | |||
| sonetLine | 1.3.6.1.2.1.10.39.1.3 | |||
| PER sonetLineCurrentCVs | 1.3.6.1.2.1.10.39.1.3.1.1.4 | PerfCurrentCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH Line in the current 15 minute interval. |
| sonetLineCurrentEntry | 1.3.6.1.2.1.10.39.1.3.1.1 | not-accessible | An entry in the SONET/SDH Line Current table. | |
| PER sonetLineCurrentESs | 1.3.6.1.2.1.10.39.1.3.1.1.2 | PerfCurrentCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval. |
| PER sonetLineCurrentSESs | 1.3.6.1.2.1.10.39.1.3.1.1.3 | PerfCurrentCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in the current 15 minute interval. |
| I32 sonetLineCurrentStatus | 1.3.6.1.2.1.10.39.1.3.1.1.1 | Integer32 | read-only | This variable indicates the status of the interface. The sonetLineCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetLineNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetLineNoDefect 2 sonetLineAIS 4 sonetLineRDI |
| sonetLineCurrentTable | 1.3.6.1.2.1.10.39.1.3.1 | not-accessible | The SONET/SDH Line Current table. | |
| PER sonetLineCurrentUASs | 1.3.6.1.2.1.10.39.1.3.1.1.5 | PerfCurrentCount | read-only | The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in the current 15 minute interval. |
| NUM sonetLineIntervalCVs | 1.3.6.1.2.1.10.39.1.3.2.1.4 | PerfIntervalCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours. |
| sonetLineIntervalEntry | 1.3.6.1.2.1.10.39.1.3.2.1 | not-accessible | An entry in the SONET/SDH Line Interval table. | |
| NUM sonetLineIntervalESs | 1.3.6.1.2.1.10.39.1.3.2.1.2 | PerfIntervalCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours. |
| I32 sonetLineIntervalNumber | 1.3.6.1.2.1.10.39.1.3.2.1.1 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM sonetLineIntervalSESs | 1.3.6.1.2.1.10.39.1.3.2.1.3 | PerfIntervalCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours. |
| sonetLineIntervalTable | 1.3.6.1.2.1.10.39.1.3.2 | not-accessible | The SONET/SDH Line Interval table. | |
| NUM sonetLineIntervalUASs | 1.3.6.1.2.1.10.39.1.3.2.1.5 | PerfIntervalCount | read-only | The counter associated with the number of Unavailable Seconds encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours. |
| T/F sonetLineIntervalValidData | 1.3.6.1.2.1.10.39.1.3.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| sonetLineStuff | 1.3.6.1.2.1.10.39.4.1.3 | A collection of objects providing information specific to SONET/SDH Line interfaces. | ||
| sonetLineStuff2 | 1.3.6.1.2.1.10.39.4.1.11 | A collection of objects providing information specific to SONET/SDH Line interfaces. | ||
| sonetMedium | 1.3.6.1.2.1.10.39.1.1 | |||
| STR sonetMediumCircuitIdentifier | 1.3.6.1.2.1.10.39.1.1.1.1.6 | DisplayString | read-write | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. Note that the circuit identifier, if available, is also represented by ifPhysAddress. |
| sonetMediumEntry | 1.3.6.1.2.1.10.39.1.1.1.1 | not-accessible | An entry in the SONET/SDH Medium table. | |
| I32 sonetMediumInvalidIntervals | 1.3.6.1.2.1.10.39.1.1.1.1.7 | Integer32 | read-only | The number of intervals in the range from 0 to sonetMediumValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). |
| INT sonetMediumLineCoding | 1.3.6.1.2.1.10.39.1.1.1.1.4 | INTEGER | read-write | This variable describes the line coding for this interface. The B3ZS and CMI are used for electrical SONET/SDH signals (STS-1 and STS-3). The Non-Return to Zero (NRZ) and the Return to Zero are used for optical SONET/SDH signals. |
| INT sonetMediumLineType | 1.3.6.1.2.1.10.39.1.1.1.1.5 | INTEGER | read-write | This variable describes the line type for this interface. The line types are Short and Long Range Single Mode fiber or Multi-Mode fiber interfaces, and coax and UTP for electrical interfaces. The value sonetOther should be used when the Line Type is not one of the listed values. |
| BIT sonetMediumLoopbackConfig | 1.3.6.1.2.1.10.39.1.1.1.1.8 | Bits | read-write | The current loopback state of the SONET/SDH interface. The values mean: sonetNoLoop Not in the loopback state. A device that is not capable of performing a loopback on this interface shall always return this value. sonetFacilityLoop The received signal at this interface is looped back out through the corresponding transmitter in the return direction. sonetTerminalLoop The signal that is about to be transmitted is connected to the associated incoming receiver. sonetOtherLoop Loopbacks that are not defined here. |
| sonetMediumStuff | 1.3.6.1.2.1.10.39.4.1.1 | A collection of objects providing configuration information applicable to all SONET/SDH interfaces. | ||
| sonetMediumStuff2 | 1.3.6.1.2.1.10.39.4.1.9 | A collection of objects providing configuration information applicable to all SONET/SDH interfaces. | ||
| sonetMediumTable | 1.3.6.1.2.1.10.39.1.1.1 | not-accessible | The SONET/SDH Medium table. | |
| I32 sonetMediumTimeElapsed | 1.3.6.1.2.1.10.39.1.1.1.1.2 | Integer32 | read-only | The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| INT sonetMediumType | 1.3.6.1.2.1.10.39.1.1.1.1.1 | INTEGER | read-write | This variable identifies whether a SONET or a SDH signal is used across this interface. |
| I32 sonetMediumValidIntervals | 1.3.6.1.2.1.10.39.1.1.1.1.3 | Integer32 | read-only | The number of previous 15-minute intervals for which data was collected. A SONET/SDH interface must be capable of supporting at least n intervals. The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available. |
| sonetMIB | 1.3.6.1.2.1.10.39 | The MIB module to describe SONET/SDH interface objects. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3592; see the RFC itself for full legal notices. | ||
| sonetObjects | 1.3.6.1.2.1.10.39.1 | |||
| sonetObjectsPath | 1.3.6.1.2.1.10.39.2 | |||
| sonetObjectsVT | 1.3.6.1.2.1.10.39.3 | |||
| sonetPath | 1.3.6.1.2.1.10.39.2.1 | |||
| PER sonetPathCurrentCVs | 1.3.6.1.2.1.10.39.2.1.1.1.5 | PerfCurrentCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH Path in the current 15 minute interval. |
| sonetPathCurrentEntry | 1.3.6.1.2.1.10.39.2.1.1.1 | not-accessible | An entry in the SONET/SDH Path Current table. | |
| PER sonetPathCurrentESs | 1.3.6.1.2.1.10.39.2.1.1.1.3 | PerfCurrentCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval. |
| PER sonetPathCurrentSESs | 1.3.6.1.2.1.10.39.2.1.1.1.4 | PerfCurrentCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in the current 15 minute interval. |
| I32 sonetPathCurrentStatus | 1.3.6.1.2.1.10.39.2.1.1.1.2 | Integer32 | read-only | This variable indicates the status of the interface. The sonetPathCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetPathNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetPathNoDefect 2 sonetPathSTSLOP 4 sonetPathSTSAIS 8 sonetPathSTSRDI 16 sonetPathUnequipped 32 sonetPathSignalLabelMismatch |
| sonetPathCurrentTable | 1.3.6.1.2.1.10.39.2.1.1 | not-accessible | The SONET/SDH Path Current table. | |
| PER sonetPathCurrentUASs | 1.3.6.1.2.1.10.39.2.1.1.1.6 | PerfCurrentCount | read-only | The counter associated with the number of Unavailable Seconds encountered by a Path in the current 15 minute interval. |
| INT sonetPathCurrentWidth | 1.3.6.1.2.1.10.39.2.1.1.1.1 | INTEGER | read-write | A value that indicates the type of the SONET/SDH Path. For SONET, the assigned types are the STS-Nc SPEs, where N = 1, 3, 12, 24, 48, 192 and 768. STS-1 is equal to 51.84 Mbps. For SDH, the assigned types are the STM-Nc VCs, where N = 1, 4, 16, 64 and 256. |
| NUM sonetPathIntervalCVs | 1.3.6.1.2.1.10.39.2.1.2.1.4 | PerfIntervalCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours. |
| sonetPathIntervalEntry | 1.3.6.1.2.1.10.39.2.1.2.1 | not-accessible | An entry in the SONET/SDH Path Interval table. | |
| NUM sonetPathIntervalESs | 1.3.6.1.2.1.10.39.2.1.2.1.2 | PerfIntervalCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours. |
| I32 sonetPathIntervalNumber | 1.3.6.1.2.1.10.39.2.1.2.1.1 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM sonetPathIntervalSESs | 1.3.6.1.2.1.10.39.2.1.2.1.3 | PerfIntervalCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours. |
| sonetPathIntervalTable | 1.3.6.1.2.1.10.39.2.1.2 | not-accessible | The SONET/SDH Path Interval table. | |
| NUM sonetPathIntervalUASs | 1.3.6.1.2.1.10.39.2.1.2.1.5 | PerfIntervalCount | read-only | The counter associated with the number of Unavailable Seconds encountered by a Path in a particular 15-minute interval in the past 24 hours. |
| T/F sonetPathIntervalValidData | 1.3.6.1.2.1.10.39.2.1.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| sonetPathStuff | 1.3.6.1.2.1.10.39.4.1.5 | A collection of objects providing information specific to SONET/SDH Path interfaces. | ||
| sonetPathStuff2 | 1.3.6.1.2.1.10.39.4.1.12 | A collection of objects providing information specific to SONET/SDH Path interfaces. | ||
| sonetSection | 1.3.6.1.2.1.10.39.1.2 | |||
| PER sonetSectionCurrentCVs | 1.3.6.1.2.1.10.39.1.2.1.1.5 | PerfCurrentCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in the current 15 minute interval. |
| sonetSectionCurrentEntry | 1.3.6.1.2.1.10.39.1.2.1.1 | not-accessible | An entry in the SONET/SDH Section Current table. | |
| PER sonetSectionCurrentESs | 1.3.6.1.2.1.10.39.1.2.1.1.2 | PerfCurrentCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval. |
| PER sonetSectionCurrentSEFSs | 1.3.6.1.2.1.10.39.1.2.1.1.4 | PerfCurrentCount | read-only | The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in the current 15 minute interval. |
| PER sonetSectionCurrentSESs | 1.3.6.1.2.1.10.39.1.2.1.1.3 | PerfCurrentCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in the current 15 minute interval. |
| I32 sonetSectionCurrentStatus | 1.3.6.1.2.1.10.39.1.2.1.1.1 | Integer32 | read-only | This variable indicates the status of the interface. The sonetSectionCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetSectionNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetSectionNoDefect 2 sonetSectionLOS 4 sonetSectionLOF |
| sonetSectionCurrentTable | 1.3.6.1.2.1.10.39.1.2.1 | not-accessible | The SONET/SDH Section Current table. | |
| NUM sonetSectionIntervalCVs | 1.3.6.1.2.1.10.39.1.2.2.1.5 | PerfIntervalCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours. |
| sonetSectionIntervalEntry | 1.3.6.1.2.1.10.39.1.2.2.1 | not-accessible | An entry in the SONET/SDH Section Interval table. | |
| NUM sonetSectionIntervalESs | 1.3.6.1.2.1.10.39.1.2.2.1.2 | PerfIntervalCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours. |
| I32 sonetSectionIntervalNumber | 1.3.6.1.2.1.10.39.1.2.2.1.1 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM sonetSectionIntervalSEFSs | 1.3.6.1.2.1.10.39.1.2.2.1.4 | PerfIntervalCount | read-only | The counter associated with the number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours. |
| NUM sonetSectionIntervalSESs | 1.3.6.1.2.1.10.39.1.2.2.1.3 | PerfIntervalCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours. |
| sonetSectionIntervalTable | 1.3.6.1.2.1.10.39.1.2.2 | not-accessible | The SONET/SDH Section Interval table. | |
| T/F sonetSectionIntervalValidData | 1.3.6.1.2.1.10.39.1.2.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| sonetSectionStuff | 1.3.6.1.2.1.10.39.4.1.2 | A collection of objects providing information specific to SONET/SDH Section interfaces. | ||
| sonetSectionStuff2 | 1.3.6.1.2.1.10.39.4.1.10 | A collection of objects providing information specific to SONET/SDH Section interfaces. | ||
| INT sonetSESthresholdSet | 1.3.6.1.2.1.10.39.1.1.2 | INTEGER | read-write | An enumerated integer indicating which recognized set of SES thresholds that the agent uses for determining severely errored seconds and unavailable time. other(1) None of the following. bellcore1991(2) Bellcore TR-NWT-000253, 1991 [TR253], or ANSI T1M1.3/93-005R2, 1993 [T1M1.3]. See also Appendix B. ansi1993(3) ANSI T1.231, 1993 [T1.231a], or Bellcore GR-253-CORE, Issue 2, 1995 [GR253] itu1995(4) ITU Recommendation G.826, 1995 [G.826] ansi1997(5) ANSI T1.231, 1997 [T1.231b] If a manager changes the value of this object then the SES statistics collected prior to this change must be invalidated. |
| sonetVT | 1.3.6.1.2.1.10.39.3.1 | |||
| PER sonetVTCurrentCVs | 1.3.6.1.2.1.10.39.3.1.1.1.5 | PerfCurrentCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH VT in the current 15 minute interval. |
| sonetVTCurrentEntry | 1.3.6.1.2.1.10.39.3.1.1.1 | not-accessible | An entry in the SONET/SDH VT Current table. | |
| PER sonetVTCurrentESs | 1.3.6.1.2.1.10.39.3.1.1.1.3 | PerfCurrentCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH VT in the current 15 minute interval. |
| PER sonetVTCurrentSESs | 1.3.6.1.2.1.10.39.3.1.1.1.4 | PerfCurrentCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH VT in the current 15 minute interval. |
| I32 sonetVTCurrentStatus | 1.3.6.1.2.1.10.39.3.1.1.1.2 | Integer32 | read-only | This variable indicates the status of the interface. The sonetVTCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects and failures simultaneously. The sonetVTNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetVTNoDefect 2 sonetVTLOP 4 sonetVTPathAIS 8 sonetVTPathRDI 16 sonetVTPathRFI 32 sonetVTUnequipped 64 sonetVTSignalLabelMismatch |
| sonetVTCurrentTable | 1.3.6.1.2.1.10.39.3.1.1 | not-accessible | The SONET/SDH VT Current table. | |
| PER sonetVTCurrentUASs | 1.3.6.1.2.1.10.39.3.1.1.1.6 | PerfCurrentCount | read-only | The counter associated with the number of Unavailable Seconds encountered by a VT in the current 15 minute interval. |
| INT sonetVTCurrentWidth | 1.3.6.1.2.1.10.39.3.1.1.1.1 | INTEGER | read-write | A value that indicates the type of the SONET VT and SDH VC. Assigned widths are VT1.5/VC11, VT2/VC12, VT3, VT6/VC2, and VT6c. |
| NUM sonetVTIntervalCVs | 1.3.6.1.2.1.10.39.3.1.2.1.4 | PerfIntervalCount | read-only | The counter associated with the number of Coding Violations encountered by a SONET/SDH VT in a particular 15-minute interval in the past 24 hours. |
| sonetVTIntervalEntry | 1.3.6.1.2.1.10.39.3.1.2.1 | not-accessible | An entry in the SONET/SDH VT Interval table. | |
| NUM sonetVTIntervalESs | 1.3.6.1.2.1.10.39.3.1.2.1.2 | PerfIntervalCount | read-only | The counter associated with the number of Errored Seconds encountered by a SONET/SDH VT in a particular 15-minute interval in the past 24 hours. |
| I32 sonetVTIntervalNumber | 1.3.6.1.2.1.10.39.3.1.2.1.1 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM sonetVTIntervalSESs | 1.3.6.1.2.1.10.39.3.1.2.1.3 | PerfIntervalCount | read-only | The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH VT in a particular 15-minute interval in the past 24 hours. |
| sonetVTIntervalTable | 1.3.6.1.2.1.10.39.3.1.2 | not-accessible | The SONET/SDH VT Interval table. | |
| NUM sonetVTIntervalUASs | 1.3.6.1.2.1.10.39.3.1.2.1.5 | PerfIntervalCount | read-only | The counter associated with the number of Unavailable Seconds encountered by a VT in a particular 15-minute interval in the past 24 hours. |
| T/F sonetVTIntervalValidData | 1.3.6.1.2.1.10.39.3.1.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| sonetVTStuff | 1.3.6.1.2.1.10.39.4.1.7 | A collection of objects providing information specific to SONET/SDH VT interfaces. | ||
| sonetVTStuff2 | 1.3.6.1.2.1.10.39.4.1.13 | A collection of objects providing information specific to SONET/SDH VT interfaces. |
RFC description
SONET/SDH synchronous optical network MIB (RFC 3592) for optical transport management.
Start monitoring vendor-neutral, standards-based MIB, SONET/SDH transport equipment and optical interface line cards (section/line/path performance/fault status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.