SOCOMECUPS-MIB

All MIBs › SOCOMECUPS-MIB

Category: Environmental Monitoring and Power, Socomec Power Management

Description: Manages Socomec UPS power configuration, battery status, input/output measurements, and alarm conditions.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SOCOMECUPS-MIB?

SOCOMECUPS-MIB is a vendor-specific MIB from Socomec, a manufacturer of uninterruptible power supply (UPS) systems used to protect critical electrical loads. It exposes data on UPS identity and firmware, battery state, input/output power measurements, and alarm/fault conditions. It is heavily used for hardware health monitoring: battery status, seconds/time remaining on battery, estimated charge remaining, battery voltage and temperature, and input line frequency all let an operator detect an aging battery, an impending outage, or overheating before the UPS fails. It loosely follows the object-naming conventions of the standard UPS-MIB (RFC 1628) for battery and input groups, though it is Socomec's own private enterprise MIB. It is typically deployed in data centers and server rooms where Socomec UPS units protect racks of IT equipment, polled by facilities or NOC monitoring systems. Engineers can download the SOCOMECUPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SOCOMECUPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Socomec UPS
power protection equipment

Monitoring Examples

An administrator would poll upsBatteryStatus and upsEstimatedMinutesRemaining together with upsEstimatedChargeRemaining to catch a battery nearing depletion during a mains outage, and would watch upsSecondsOnBattery to see how long the unit has already been running unpowered. upsBatteryTemperature and upsBatteryVoltage reveal thermal stress or cell degradation, while upsInputFrequency and upsInputNumLines confirm the incoming utility feed is stable. A sudden jump in upsSecondsOnBattery combined with falling upsEstimatedChargeRemaining is a classic signal of an unexpected power event in progress.

What Can Be Monitored

battery status
estimated runtime remaining
battery charge percentage
battery voltage and temperature
input line frequency
firmware and serial number identity

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

enterprises

From SNMPv2-TC

AutonomousType
DisplayString
TestAndIncr
TimeInterval
TimeStamp

OIDs

OID symbolic	OID numeric	Type	Access	Description
socomecSicon	1.3.6.1.4.1.4555
software	1.3.6.1.4.1.4555.1
network	1.3.6.1.4.1.4555.1.1
netvision	1.3.6.1.4.1.4555.1.1.1
upsObjects	1.3.6.1.4.1.4555.1.1.1.1
upsIdent	1.3.6.1.4.1.4555.1.1.1.1.1
STR upsIdentModel	1.3.6.1.4.1.4555.1.1.1.1.1.1	DisplayString	read-only	The UPS Model designation.
STR upsIdentUPSFirmwareVersion	1.3.6.1.4.1.4555.1.1.1.1.1.2	DisplayString	read-only	The UPS firmware version.
STR upsIdentAgentSoftwareVersion	1.3.6.1.4.1.4555.1.1.1.1.1.3	DisplayString	read-only	The UPS Net Vision software version.
STR upsIdentUpsSerialNumber	1.3.6.1.4.1.4555.1.1.1.1.1.4	DisplayString	read-only	The UPS serial no.
upsBattery	1.3.6.1.4.1.4555.1.1.1.1.2
INT upsBatteryStatus	1.3.6.1.4.1.4555.1.1.1.1.2.1	INTEGER	read-only	The present battery status
INT upsSecondsOnBattery	1.3.6.1.4.1.4555.1.1.1.1.2.2	INTEGER	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. -1 shall be returned if the unit is not on battery power.
INT upsEstimatedMinutesRemaining	1.3.6.1.4.1.4555.1.1.1.1.2.3	INTEGER	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.
INT upsEstimatedChargeRemaining	1.3.6.1.4.1.4555.1.1.1.1.2.4	INTEGER	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.
INT upsBatteryVoltage	1.3.6.1.4.1.4555.1.1.1.1.2.5	INTEGER	read-only	The magnitude of the present battery voltage in 0.1 Volt DC.
INT upsBatteryTemperature	1.3.6.1.4.1.4555.1.1.1.1.2.6	INTEGER	read-only	The ambient temperature at or near the UPS Battery casing.
upsInput	1.3.6.1.4.1.4555.1.1.1.1.3
INT upsInputNumLines	1.3.6.1.4.1.4555.1.1.1.1.3.1	INTEGER	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.
INT upsInputFrequency	1.3.6.1.4.1.4555.1.1.1.1.3.2	INTEGER	read-only	The current input frequency to the UPS system in 0.1 HZ.
upsInputTable	1.3.6.1.4.1.4555.1.1.1.1.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.
upsInputEntry	1.3.6.1.4.1.4555.1.1.1.1.3.3.1		not-accessible	An entry containing information applicable to a particular input line.
INT upsInputLineIndex	1.3.6.1.4.1.4555.1.1.1.1.3.3.1.1	INTEGER	read-only
INT upsInputVoltage	1.3.6.1.4.1.4555.1.1.1.1.3.3.1.2	INTEGER	read-only	The input utility line voltage in 0.1 volts.
INT upsInputCurrent	1.3.6.1.4.1.4555.1.1.1.1.3.3.1.3	INTEGER	read-only	The magnitude of the present input current in 0.1 A.
INT upsInputVoltageMax	1.3.6.1.4.1.4555.1.1.1.1.3.3.1.4	INTEGER	read-only	The maximum utility line voltage in 0.1 VAC for last 1 minute.
INT upsInputVoltageMin	1.3.6.1.4.1.4555.1.1.1.1.3.3.1.5	INTEGER	read-only	The minimum utility line voltage in 0.1 VAC for last 1 minute.
upsOutput	1.3.6.1.4.1.4555.1.1.1.1.4
INT upsOutputSource	1.3.6.1.4.1.4555.1.1.1.1.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.
INT upsOutputFrequency	1.3.6.1.4.1.4555.1.1.1.1.4.2	INTEGER	read-only	The current output frequency of the UPS system in 0.1 of HZ.
INT upsOutputNumLines	1.3.6.1.4.1.4555.1.1.1.1.4.3	INTEGER	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.
upsOutputTable	1.3.6.1.4.1.4555.1.1.1.1.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.
upsOutputEntry	1.3.6.1.4.1.4555.1.1.1.1.4.4.1		not-accessible	An entry containing information applicable to a particular output line.
INT upsOutputLineIndex	1.3.6.1.4.1.4555.1.1.1.1.4.4.1.1	INTEGER	read-only	The output line identifier.
INT upsOutputVoltage	1.3.6.1.4.1.4555.1.1.1.1.4.4.1.2	INTEGER	read-only	The output voltage of the UPS system in 0.1 volts.
INT upsOutputCurrent	1.3.6.1.4.1.4555.1.1.1.1.4.4.1.3	INTEGER	read-only	The output current of the UPS system in 0.1 Amps.
INT upsOutputPercentLoad	1.3.6.1.4.1.4555.1.1.1.1.4.4.1.4	INTEGER	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.
INT upsOutputKva	1.3.6.1.4.1.4555.1.1.1.1.4.4.1.5	INTEGER	read-only	Output KVA.
upsBypass	1.3.6.1.4.1.4555.1.1.1.1.5
INT upsBypassFrequency	1.3.6.1.4.1.4555.1.1.1.1.5.1	INTEGER	read-only	The present bypass frequency.
INT upsBypassNumLines	1.3.6.1.4.1.4555.1.1.1.1.5.2	INTEGER	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
upsBypassTable	1.3.6.1.4.1.4555.1.1.1.1.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.
upsBypassEntry	1.3.6.1.4.1.4555.1.1.1.1.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.
INT upsBypassLineIndex	1.3.6.1.4.1.4555.1.1.1.1.5.3.1.1	INTEGER	read-only	The bypass line identifier.
INT upsBypassVoltage	1.3.6.1.4.1.4555.1.1.1.1.5.3.1.2	INTEGER	read-only	The present bypass voltage.
INT upsBypassCurrent	1.3.6.1.4.1.4555.1.1.1.1.5.3.1.3	INTEGER	read-only	The present bypass current.
upsAlarm	1.3.6.1.4.1.4555.1.1.1.1.6
INT upsAlarmsPresent	1.3.6.1.4.1.4555.1.1.1.1.6.1	INTEGER	read-only	The present number of active alarm conditions.
upsAlarmTable	1.3.6.1.4.1.4555.1.1.1.1.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an OBJECT IDENTIFIER, upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.
upsAlarmEntry	1.3.6.1.4.1.4555.1.1.1.1.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.
NUM upsAlarmId	1.3.6.1.4.1.4555.1.1.1.1.6.2.1.1	PositiveInteger	read-only	A unique identifier for an alarm condition. This value must remain constant.
OID upsAlarmDescr	1.3.6.1.4.1.4555.1.1.1.1.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.
TIM upsAlarmTime	1.3.6.1.4.1.4555.1.1.1.1.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.
STR upsAlarmExtDes	1.3.6.1.4.1.4555.1.1.1.1.6.2.1.4	DisplayString	read-only	Extra description.
upsWellKnownAlarms	1.3.6.1.4.1.4555.1.1.1.1.6.3
INT upsAlarmBatteryBad	1.3.6.1.4.1.4555.1.1.1.1.6.3.1	INTEGER	read-only	One or more batteries have been determined to require replacement.
INT upsAlarmOnBattery	1.3.6.1.4.1.4555.1.1.1.1.6.3.2	INTEGER	read-only	The UPS is drawing power from the batteries.
INT upsAlarmLowBattery	1.3.6.1.4.1.4555.1.1.1.1.6.3.3	INTEGER	read-only	The remaining battery run-time is less than or equal to upsConfigLowBattTime.
INT upsAlarmDepletedBattery	1.3.6.1.4.1.4555.1.1.1.1.6.3.4	INTEGER	read-only	The UPS will be unable to sustain the present load when and if the utility power is lost.
INT upsAlarmTempBad	1.3.6.1.4.1.4555.1.1.1.1.6.3.5	INTEGER	read-only	A temperature is out of tolerance.
INT upsAlarmInputBad	1.3.6.1.4.1.4555.1.1.1.1.6.3.6	INTEGER	read-only	An input condition is out of tolerance.
INT upsAlarmOutputBad	1.3.6.1.4.1.4555.1.1.1.1.6.3.7	INTEGER	read-only	An output condition (other than OutputOverload) is out of tolerance.
INT upsAlarmOutputOverload	1.3.6.1.4.1.4555.1.1.1.1.6.3.8	INTEGER	read-only	The output load exceeds the UPS output capacity.
INT upsAlarmOnBypass	1.3.6.1.4.1.4555.1.1.1.1.6.3.9	INTEGER	read-only	The Bypass is presently engaged on the UPS.
INT upsAlarmBypassBad	1.3.6.1.4.1.4555.1.1.1.1.6.3.10	INTEGER	read-only	The Bypass is out of tolerance.
INT upsAlarmOutputOffAsRequested	1.3.6.1.4.1.4555.1.1.1.1.6.3.11	INTEGER	read-only	The UPS has shutdown as requested, i.e., the output is off.
INT upsAlarmUpsOffAsRequested	1.3.6.1.4.1.4555.1.1.1.1.6.3.12	INTEGER	read-only	The entire UPS has shutdown as commanded.
INT upsAlarmChargerFailed	1.3.6.1.4.1.4555.1.1.1.1.6.3.13	INTEGER	read-only	An uncorrected problem has been detected within the UPS charger subsystem.
INT upsAlarmUpsOutputOff	1.3.6.1.4.1.4555.1.1.1.1.6.3.14	INTEGER	read-only	The output of the UPS is in the off state.
INT upsAlarmUpsSystemOff	1.3.6.1.4.1.4555.1.1.1.1.6.3.15	INTEGER	read-only	The UPS system is in the off state.
INT upsAlarmFanFailure	1.3.6.1.4.1.4555.1.1.1.1.6.3.16	INTEGER	read-only	The failure of one or more fans in the UPS has been detected.
INT upsAlarmFuseFailure	1.3.6.1.4.1.4555.1.1.1.1.6.3.17	INTEGER	read-only	The failure of one or more fuses has been detected.
INT upsAlarmGeneralFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.18	INTEGER	read-only	A general fault in the UPS has been detected.
INT upsAlarmDiagnosticTestFailed	1.3.6.1.4.1.4555.1.1.1.1.6.3.19	INTEGER	read-only	The result of the last diagnostic test indicates a failure.
INT upsAlarmCommunicationLost	1.3.6.1.4.1.4555.1.1.1.1.6.3.20	INTEGER	read-only	A problem has been encountered in the communications between the agent and the UPS.
INT upsAlarmAwaitingPower	1.3.6.1.4.1.4555.1.1.1.1.6.3.21	INTEGER	read-only	The UPS output is off and the UPS is awaiting the return of input power.
INT upsAlarmShutdownPending	1.3.6.1.4.1.4555.1.1.1.1.6.3.22	INTEGER	read-only	A upsShutdownAfterDelay countdown is underway.
INT upsAlarmShutdownImminent	1.3.6.1.4.1.4555.1.1.1.1.6.3.23	INTEGER	read-only	The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
INT upsAlarmTestInProgress	1.3.6.1.4.1.4555.1.1.1.1.6.3.24	INTEGER	read-only	A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-TYPE macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-TYPE.
INT upsAlarmPowerSupplyFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.25	INTEGER	read-only	Digital power supply fault.
INT upsAlarmAuxMainFail	1.3.6.1.4.1.4555.1.1.1.1.6.3.26	INTEGER	read-only	Auxiliary mains out of tolerance.
INT upsAlarmManualBypassClose	1.3.6.1.4.1.4555.1.1.1.1.6.3.27	INTEGER	read-only	Manual By-pass closed
INT upsAlarmShortCircuit	1.3.6.1.4.1.4555.1.1.1.1.6.3.28	INTEGER	read-only	Short Circuit on UPS output.
INT upsAlarmBatteryChargerFailure	1.3.6.1.4.1.4555.1.1.1.1.6.3.29	INTEGER	read-only	Battery charger failure.
INT upsAlarmInverterOverCurrent	1.3.6.1.4.1.4555.1.1.1.1.6.3.30	INTEGER	read-only	Inverter Over-current.
INT upsAlarmInverterDistorsion	1.3.6.1.4.1.4555.1.1.1.1.6.3.31	INTEGER	read-only	Excessive Inverter Distorsion.
INT upsAlarmPrechargeVoltageFail	1.3.6.1.4.1.4555.1.1.1.1.6.3.32	INTEGER	read-only	Precharge voltage out of tolerance.
INT upsAlarmBoostTooLow	1.3.6.1.4.1.4555.1.1.1.1.6.3.33	INTEGER	read-only	Boost output voltage too low.
INT upsAlarmBoostTooHigh	1.3.6.1.4.1.4555.1.1.1.1.6.3.34	INTEGER	read-only	Boost output voltage too high.
INT upsAlarmBatteryTooHigh	1.3.6.1.4.1.4555.1.1.1.1.6.3.35	INTEGER	read-only	Battery voltage too high.
INT upsAlarmImproperCondition	1.3.6.1.4.1.4555.1.1.1.1.6.3.36	INTEGER	read-only	Improper condition of use
INT upsAlarmOverloadTimeout	1.3.6.1.4.1.4555.1.1.1.1.6.3.37	INTEGER	read-only	Overload timeout blocking Inverter.
INT upsAlarmControlSystemFailure	1.3.6.1.4.1.4555.1.1.1.1.6.3.38	INTEGER	read-only	Microprocessor control system failure
INT upsAlarmDataCorrupted	1.3.6.1.4.1.4555.1.1.1.1.6.3.39	INTEGER	read-only	Configuration data map corrupted.
INT upsAlarmPllFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.40	INTEGER	read-only	Pll fault.
INT upsAlarmInputGeneralAlarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.41	INTEGER	read-only	Input mains general alarm.
INT upsAlarmRectifierGeneralAlarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.42	INTEGER	read-only	Rectifier general alarm.
INT upsAlarmBoostGeneralAlarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.43	INTEGER	read-only	Boost general alarm.
INT upsAlarmInverterGeneralAlarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.44	INTEGER	read-only	Inverter general alarm.
INT upsAlarmBatteryGeneralAlarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.45	INTEGER	read-only	Bettery charger general alarm.
INT upsAlarmOutputOver	1.3.6.1.4.1.4555.1.1.1.1.6.3.46	INTEGER	read-only	Output voltage over limit.
INT upsAlarmOutputUnder	1.3.6.1.4.1.4555.1.1.1.1.6.3.47	INTEGER	read-only	Output voltage under limit.
INT upsAlarmBypassGeneralAlarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.48	INTEGER	read-only	Bypass charger general alarm.
INT upsAlarmStopForOverload	1.3.6.1.4.1.4555.1.1.1.1.6.3.49	INTEGER	read-only	Stop for overload.
INT upsAlarmImminentStop	1.3.6.1.4.1.4555.1.1.1.1.6.3.50	INTEGER	read-only	UPS imminent stop
INT upsAlarmModule1Alarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.51	INTEGER	read-only	Module 1 in parallel general alarm.
INT upsAlarmModule2Alarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.52	INTEGER	read-only	Module 2 in parallel general alarm.
INT upsAlarmModule3Alarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.53	INTEGER	read-only	Module 3 in parallel general alarm.
INT upsAlarmModule4Alarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.54	INTEGER	read-only	Module 4 in parallel general alarm.
INT upsAlarmModule5Alarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.55	INTEGER	read-only	Module 5 in parallel general alarm.
INT upsAlarmModule6Alarm	1.3.6.1.4.1.4555.1.1.1.1.6.3.56	INTEGER	read-only	Module 6 in parallel general alarm.
INT upsAlarmExternalAlarm1	1.3.6.1.4.1.4555.1.1.1.1.6.3.57	INTEGER	read-only	External Alarm 1.
INT upsAlarmExternalAlarm2	1.3.6.1.4.1.4555.1.1.1.1.6.3.58	INTEGER	read-only	External Alarm 2.
INT upsAlarmExternalAlarm3	1.3.6.1.4.1.4555.1.1.1.1.6.3.59	INTEGER	read-only	External Alarm 3.
INT upsAlarmExternalAlarm4	1.3.6.1.4.1.4555.1.1.1.1.6.3.60	INTEGER	read-only	External Alarm 4.
INT upsAlarmEService	1.3.6.1.4.1.4555.1.1.1.1.6.3.61	INTEGER	read-only	E-Service General Alarm
INT upsAlarmRedundancyLost	1.3.6.1.4.1.4555.1.1.1.1.6.3.62	INTEGER	read-only	Redundancy lost
INT upsAlarmPeriodicServiceCheck	1.3.6.1.4.1.4555.1.1.1.1.6.3.63	INTEGER	read-only	Periodic service check up.
INT upsAlarmAllTransferDisabled	1.3.6.1.4.1.4555.1.1.1.1.6.3.64	INTEGER	read-only	Automatic and manual transfer disabled
INT upsAlarmAutoTransferDisabled	1.3.6.1.4.1.4555.1.1.1.1.6.3.65	INTEGER	read-only	Automatic transfer disabled
INT upsAlarmBatteryRoom	1.3.6.1.4.1.4555.1.1.1.1.6.3.66	INTEGER	read-only	Battery room alarm
INT upsAlarmManualBypass	1.3.6.1.4.1.4555.1.1.1.1.6.3.67	INTEGER	read-only	Manual bypass alarm
INT upsAlarmBatteryDischarged	1.3.6.1.4.1.4555.1.1.1.1.6.3.68	INTEGER	read-only	Battery Discharged
INT upsAlarmInsufficientResources	1.3.6.1.4.1.4555.1.1.1.1.6.3.69	INTEGER	read-only	Insufficient resources
INT upsAlarmOptionalBoards	1.3.6.1.4.1.4555.1.1.1.1.6.3.70	INTEGER	read-only	Optional boards general alarm
INT upsAlarmRectifierFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.71	INTEGER	read-only	Rectifier fault
INT upsAlarmBoostFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.72	INTEGER	read-only	Boost fault
INT upsAlarmInverterFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.73	INTEGER	read-only	Inverter fault
INT upsAlarmParallelModuleFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.74	INTEGER	read-only	Parallel module fault
INT upsAlarmGenSetGeneral	1.3.6.1.4.1.4555.1.1.1.1.6.3.75	INTEGER	read-only	Gen-set general alarm
INT upsAlarmGenSetFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.76	INTEGER	read-only	Gen-set fault
INT upsAlarmEmergencyStopActive	1.3.6.1.4.1.4555.1.1.1.1.6.3.77	INTEGER	read-only	Emergency stop active
INT upsAlarmBatteryCircuitOpen	1.3.6.1.4.1.4555.1.1.1.1.6.3.78	INTEGER	read-only	Battery circuit open
INT upsAlarmFansFailure	1.3.6.1.4.1.4555.1.1.1.1.6.3.79	INTEGER	read-only	Fans failure
INT upsAlarmPhaseRotationFault	1.3.6.1.4.1.4555.1.1.1.1.6.3.80	INTEGER	read-only	Phase rotation fault
INT upsAlarmA62	1.3.6.1.4.1.4555.1.1.1.1.6.3.81	INTEGER	read-only	A62.
INT upsAlarmA63	1.3.6.1.4.1.4555.1.1.1.1.6.3.82	INTEGER	read-only	A63.
upsTest	1.3.6.1.4.1.4555.1.1.1.1.7
OID upsTestId	1.3.6.1.4.1.4555.1.1.1.1.7.1	OBJECT IDENTIFIER	read-write	The test named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of test, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. Tests in progress may be aborted by setting this variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has bee run, in which case the well known value upsTestNoTestsInitiated is returned.
TES upsTestSpinLock	1.3.6.1.4.1.4555.1.1.1.1.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try_again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock_value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock_value, upsTestId = requested_test) if (error_index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try_again } if (error_index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock_value + 1, then these are our test / / results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.
INT upsTestResultsSummary	1.3.6.1.4.1.4555.1.1.1.1.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.
STR upsTestResultsDetail	1.3.6.1.4.1.4555.1.1.1.1.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.
TIM upsTestStartTime	1.3.6.1.4.1.4555.1.1.1.1.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.
NUM upsTestElapsedTime	1.3.6.1.4.1.4555.1.1.1.1.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.
upsWellKnownTests	1.3.6.1.4.1.4555.1.1.1.1.7.7
INT upsTestNoTestsInitiated	1.3.6.1.4.1.4555.1.1.1.1.7.7.1	INTEGER	read-only	No tests have been initiated and no test is in progress.
INT upsTestAbortTestInProgress	1.3.6.1.4.1.4555.1.1.1.1.7.7.2	INTEGER	read-only	The test in progress is to be aborted / the test in progress was aborted.
INT upsTestGeneralSystemsTest	1.3.6.1.4.1.4555.1.1.1.1.7.7.3	INTEGER	read-only	The manufacturer's standard test of UPS device systems.
INT upsTestQuickBatteryTest	1.3.6.1.4.1.4555.1.1.1.1.7.7.4	INTEGER	read-only	A test that is sufficient to determine if the battery needs replacement.
INT upsDeepBatteryCalibration	1.3.6.1.4.1.4555.1.1.1.1.7.7.5	INTEGER	read-only	The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.
upsControl	1.3.6.1.4.1.4555.1.1.1.1.8
INT upsControlStatusControl	1.3.6.1.4.1.4555.1.1.1.1.8.1	INTEGER	read-write	This object Control UPS status
INT upsShutdownDelay	1.3.6.1.4.1.4555.1.1.1.1.8.2	INTEGER	read-write	This object set the delay time (in seconds) to turn UPS off after Net Vision broadcast shutdown request to connected clients
INT upsTurnOffAfterShutdown	1.3.6.1.4.1.4555.1.1.1.1.8.3	INTEGER	read-write	This object enable/disable UPS turn off function after shutdown process complete
upsControlShutdownParametersTable	1.3.6.1.4.1.4555.1.1.1.1.8.4		not-accessible	Table which describes the parametes for shutdown process when shutdown event occurs
shutdownParametersEntry	1.3.6.1.4.1.4555.1.1.1.1.8.4.1		not-accessible
STR upsControlEventDescr	1.3.6.1.4.1.4555.1.1.1.1.8.4.1.1	DisplayString	read-only	The shutdown event identification
INT upsControlEventStatus	1.3.6.1.4.1.4555.1.1.1.1.8.4.1.2	INTEGER	read-write	Status of the corresponding shutdown Event. When set to disable(), shutdown process will not start when corresponding event occured.
INT upsControlDelay	1.3.6.1.4.1.4555.1.1.1.1.8.4.1.3	INTEGER	read-write	The Delay after the occurance of the curresponding shutdown event that Net Vision should issue shutdown request to connected clients. For WeeklyScheduledShutdown and SpecialScheduledShutdown, this is the time before the configured Shutdowntime when Net Vision will start sending the warning message to the connected clients. The value is in units of minutes.
INT upsControlFirstWarning	1.3.6.1.4.1.4555.1.1.1.1.8.4.1.4	INTEGER	read-write	The delay after the occurance of the curresponding shutdown event that the Net Vision will start sending the warning message to the connected clients. The value is in units of seconds
INT upsControlWarningInterval	1.3.6.1.4.1.4555.1.1.1.1.8.4.1.5	INTEGER	read-write	The frequency of sending warning messages to the connected clients when the curresponding shutdown event occurs. The value is in units of seconds.
INT upsControlSeverity	1.3.6.1.4.1.4555.1.1.1.1.8.4.1.6	INTEGER	read-write	Shutdown daemon severity.
upsControlWeeklyScheduleTable	1.3.6.1.4.1.4555.1.1.1.1.8.5		not-accessible	The table to schedule shutting down the ups by weekly.
upsControlWeeklyScheduleEntry	1.3.6.1.4.1.4555.1.1.1.1.8.5.1		not-accessible	The entries for each day.
INT upsControlWeeklyIndex	1.3.6.1.4.1.4555.1.1.1.1.8.5.1.1	INTEGER	read-only	The index of scheduled events.
INT upsControlWeeklyShutdownDay	1.3.6.1.4.1.4555.1.1.1.1.8.5.1.2	INTEGER	read-write	The weekday on which the UPS should shut down.
STR upsControlWeeklyShutdownTime	1.3.6.1.4.1.4555.1.1.1.1.8.5.1.3	DisplayString	read-write	The time that the process of shutting down the UPS will be initiated in hh:mm:ss format.
INT upsControlWeeklyRestartDay	1.3.6.1.4.1.4555.1.1.1.1.8.5.1.4	INTEGER	read-write	The weekday on which the UPS should restart
STR upsControlWeeklyRestartTime	1.3.6.1.4.1.4555.1.1.1.1.8.5.1.5	DisplayString	read-write	The time the UPS will restart in hh:mm:ss format.
upsControlSpecialScheduleTable	1.3.6.1.4.1.4555.1.1.1.1.8.6		not-accessible	The table to schedule shutting down the ups.
upsControlSpecialScheduleEntry	1.3.6.1.4.1.4555.1.1.1.1.8.6.1		not-accessible	The entries for each day.
INT upsControlSpecialIndex	1.3.6.1.4.1.4555.1.1.1.1.8.6.1.1	INTEGER	read-only	The index of scheduled events.
STR upsControlSpecialShutdownDay	1.3.6.1.4.1.4555.1.1.1.1.8.6.1.2	DisplayString	read-write	The date on which the UPS should shut down in dd/mm/yyyy format.
STR upsControlSpecialShutdownTime	1.3.6.1.4.1.4555.1.1.1.1.8.6.1.3	DisplayString	read-write	The time that the process of shutting down the UPS will be initiated in hh:mm:ss format
STR upsControlSpecialRestartDay	1.3.6.1.4.1.4555.1.1.1.1.8.6.1.4	DisplayString	read-write	The date on which the UPS should restart in dd/mm/yyyy format
STR upsControlSpecialRestartTime	1.3.6.1.4.1.4555.1.1.1.1.8.6.1.5	DisplayString	read-write	The time the UPS will restart in hh:mm:ss format.
upsControlEcoModeScheduleTable	1.3.6.1.4.1.4555.1.1.1.1.8.7		not-accessible	The table to schedule enable/disable ups eco/mode by weekly.
upsControlEcoModeScheduleEntry	1.3.6.1.4.1.4555.1.1.1.1.8.7.1		not-accessible	The entries for each day.
INT upsControlEcoModeIndex	1.3.6.1.4.1.4555.1.1.1.1.8.7.1.1	INTEGER	read-only	The index of scheduled events.
INT upsControlEcoModeStartDay	1.3.6.1.4.1.4555.1.1.1.1.8.7.1.2	INTEGER	read-write	The weekday on which the UPS Eco/Mode should enable.
STR upsControlEcoModeStartTime	1.3.6.1.4.1.4555.1.1.1.1.8.7.1.3	DisplayString	read-write	The time that the UPS Eco/Mode will be enabled, in hh:mm:ss format.
INT upsControlEcoModeEndDay	1.3.6.1.4.1.4555.1.1.1.1.8.7.1.4	INTEGER	read-write	The weekday on which the UPS Eco/Mode should disable
STR upsControlEcoModeEndTime	1.3.6.1.4.1.4555.1.1.1.1.8.7.1.5	DisplayString	read-write	The time the UPS Eco/Mode will disabled, in hh:mm:ss format.
upsConfig	1.3.6.1.4.1.4555.1.1.1.1.9
INT upsConfigInputVoltage	1.3.6.1.4.1.4555.1.1.1.1.9.1	INTEGER	read-only	The magnitude of the nominal input voltage.
INT upsConfigInputFreq	1.3.6.1.4.1.4555.1.1.1.1.9.2	INTEGER	read-only	The nominal input frequency.
INT upsConfigOutputVoltage	1.3.6.1.4.1.4555.1.1.1.1.9.3	INTEGER	read-only	The magnitude of the nominal output voltage.
INT upsConfigOutputFreq	1.3.6.1.4.1.4555.1.1.1.1.9.4	INTEGER	read-only	The nominal output frequency.
upsDevicesTable	1.3.6.1.4.1.4555.1.1.1.1.9.5		not-accessible	The devices powered by UPS and registered to Net Vision
upsDevicesEntry	1.3.6.1.4.1.4555.1.1.1.1.9.5.1		not-accessible	The devices protected by Net Vision
INT indexOfDevice	1.3.6.1.4.1.4555.1.1.1.1.9.5.1.1	INTEGER	read-only	The index of the device that is plugged into the UPS.
IP addrOfDevice	1.3.6.1.4.1.4555.1.1.1.1.9.5.1.2	IpAddress	read-only	The ip address of the device.
STR nameOfDevice	1.3.6.1.4.1.4555.1.1.1.1.9.5.1.3	DisplayString	read-only	The name/description of the device plugged into the UPS.
STR timeOfConnection	1.3.6.1.4.1.4555.1.1.1.1.9.5.1.4	DisplayString	read-only	The that device registered to Net Vision
INT statusOfConnection	1.3.6.1.4.1.4555.1.1.1.1.9.5.1.5	INTEGER	read-only	status
INT severityOfConnection	1.3.6.1.4.1.4555.1.1.1.1.9.5.1.6	INTEGER	read-only	severity
upsAgent	1.3.6.1.4.1.4555.1.1.1.1.10
IP upsAgentIpaddress	1.3.6.1.4.1.4555.1.1.1.1.10.1	IpAddress	read-write	The ip address that NMS can identify the managed device
IP upsAgentGateway	1.3.6.1.4.1.4555.1.1.1.1.10.2	IpAddress	read-write	The default gateway that allow device managed through routers
IP upsAgentSubnetMask	1.3.6.1.4.1.4555.1.1.1.1.10.3	IpAddress	read-write	Internet address subnet mask
STR upsAgentDate	1.3.6.1.4.1.4555.1.1.1.1.10.4	DisplayString	read-write	The date in agent, format is (dd/mm/yyyy)
STR upsAgentTime	1.3.6.1.4.1.4555.1.1.1.1.10.5	DisplayString	read-write	The time in agent, format is (hh:mm:ss)
STR upsAgentNtpTimeServer	1.3.6.1.4.1.4555.1.1.1.1.10.6	DisplayString	read-write
INT upsAgentNtpTimeZone	1.3.6.1.4.1.4555.1.1.1.1.10.7	INTEGER	read-write
INT upsAgentHistoryLogFrequency	1.3.6.1.4.1.4555.1.1.1.1.10.8	INTEGER	read-write	The frequency of the updation of the history log. The value is in seconds
INT upsAgentExtHistoryLogFrequency	1.3.6.1.4.1.4555.1.1.1.1.10.9	INTEGER	read-write	The ups parameters are sampled at the rate governed by the mconfigHistroyLogFrequency. These sampled values are further conslidated over period of time which is determined by this object.
INT upsAgentPollRate	1.3.6.1.4.1.4555.1.1.1.1.10.10	INTEGER	read-write	The frequency that proxy agent polls the connected UPS in JBUS protocol. (unit : second)
INT upsAgentBaudRate	1.3.6.1.4.1.4555.1.1.1.1.10.11	INTEGER	read-write	The serial port communication speed (2400/9600 allowed).
INT upsAgentDhcpStatus	1.3.6.1.4.1.4555.1.1.1.1.10.12	INTEGER	read-write	Enable or disable DHCP-BootP capability
INT upsAgentTelnetStatus	1.3.6.1.4.1.4555.1.1.1.1.10.13	INTEGER	read-write	Enable or disable telnet access
INT upsAgentTftpStatus	1.3.6.1.4.1.4555.1.1.1.1.10.14	INTEGER	read-write	Enable or disable network upgrade capability
INT upsAgentResetToDefault	1.3.6.1.4.1.4555.1.1.1.1.10.15	INTEGER	read-write	Reset all parameters of Net Vision to default value
INT upsAgentRestart	1.3.6.1.4.1.4555.1.1.1.1.10.16	INTEGER	read-write	Restart Net Vision
INT upsAgentClearAgentLog	1.3.6.1.4.1.4555.1.1.1.1.10.17	INTEGER	read-write	Clear agent log data
INT upsAgentClearEventLog	1.3.6.1.4.1.4555.1.1.1.1.10.18	INTEGER	read-write	Clear event log data
INT upsAgentClearExtHistoryLog	1.3.6.1.4.1.4555.1.1.1.1.10.19	INTEGER	read-write	Clear extented history log data
INT upsAgentClearHistoryLog	1.3.6.1.4.1.4555.1.1.1.1.10.20	INTEGER	read-write	Clear history log data
upsAgentTrapsReceiversTable	1.3.6.1.4.1.4555.1.1.1.1.10.21		not-accessible	A list of managers to send traps to. The number of entries is given by the value of upsAgentNumTrapReceivers
upsAgentTrapsReceiversEntry	1.3.6.1.4.1.4555.1.1.1.1.10.21.1		not-accessible	The managers to send traps to.
INT trapsIndex	1.3.6.1.4.1.4555.1.1.1.1.10.21.1.1	INTEGER	read-only	The index to a trap receiver entry.
STR trapsReceiverAddr	1.3.6.1.4.1.4555.1.1.1.1.10.21.1.2	DisplayString	read-write	The IP address of the manager to send a trap to.
STR receiverCommunityString	1.3.6.1.4.1.4555.1.1.1.1.10.21.1.3	DisplayString	read-write	The community name to use in the trap when sent to the manager.
STR receiverDescription	1.3.6.1.4.1.4555.1.1.1.1.10.21.1.4	DisplayString	read-write	Description of trap receivers
upsAgentAccessControlTable	1.3.6.1.4.1.4555.1.1.1.1.10.22		not-accessible	A list of managers which can access Net Vision with private community string.
upsAgentAccessControlEntry	1.3.6.1.4.1.4555.1.1.1.1.10.22.1		not-accessible	The managers.
INT accessIndex	1.3.6.1.4.1.4555.1.1.1.1.10.22.1.1	INTEGER	read-only	The index to a access control entry.
STR accessControlAddr	1.3.6.1.4.1.4555.1.1.1.1.10.22.1.2	DisplayString	read-write	The IP address of the manager to access Net Vision
STR accessCommunityString	1.3.6.1.4.1.4555.1.1.1.1.10.22.1.3	DisplayString	read-write	The community name to use in the manager when access Net Vision
INT accessControlMode	1.3.6.1.4.1.4555.1.1.1.1.10.22.1.4	INTEGER	read-write	Access type, only read-Write access type can change parameter of Net Vision
INT upsAgentMibVersion	1.3.6.1.4.1.4555.1.1.1.1.10.23	INTEGER	read-only	The version of MIB spec.
STR upsAgentTrapString	1.3.6.1.4.1.4555.1.1.1.1.10.50	DisplayString	read-only	This OID allows traps to be sent with an octet string argument that my not be defined in the. A get of this OID will return error or NULL string.
emdStatus	1.3.6.1.4.1.4555.1.1.1.1.11
INT emdSatatusTemperature	1.3.6.1.4.1.4555.1.1.1.1.11.1	INTEGER	read-only	The measurement of EMD temperature, in 0.1 degree
INT emdSatatusHumidity	1.3.6.1.4.1.4555.1.1.1.1.11.2	INTEGER	read-only	The measurement of EMD humidity, in 0.1 degree
upsTraps	1.3.6.1.4.1.4555.1.1.1.2
NTF upsTrapOnBattery	1.3.6.1.4.1.4555.1.1.1.2.0.1			The UPS is operating on battery power. This trap is persistent and is resent at one minute intervals until the UPS either turns off or is no longer running on battery.
NTF upsTrapTestCompleted	1.3.6.1.4.1.4555.1.1.1.2.0.2			This trap is sent upon completion of a UPS diagnostic test.
NTF upsTrapAlarmEntryAdded	1.3.6.1.4.1.4555.1.1.1.2.0.3			This trap is sent each time an alarm is inserted into to the alarm table. It is sent on the insertion of all alarms except for upsAlarmOnBattery and upsAlarmTestInProgress.
NTF upsTrapAlarmEntryRemoved	1.3.6.1.4.1.4555.1.1.1.2.0.4			This trap is sent each time an alarm is removed from the alarm table. It is sent on the removal of all alarms except for upsAlarmTestInProgress.
NTF upsTrapUpsNormal	1.3.6.1.4.1.4555.1.1.1.2.0.5			INFORMATION: The UPS status is normal.
NTF upsTrapUpsBattTestFailed	1.3.6.1.4.1.4555.1.1.1.2.0.6			SEVERE: UPS failed the last test of battery.
NTF upsTrapOnBatteryPower	1.3.6.1.4.1.4555.1.1.1.2.0.7			WARNING: The UPS has switched to battery backup power.
NTF upsTrapBatteryLow	1.3.6.1.4.1.4555.1.1.1.2.0.8			SEVERE: Battery is near to be discharged.
NTF upsTrapPowerRestored	1.3.6.1.4.1.4555.1.1.1.2.0.9			INFORMATION: Input power has been restored.
NTF upsTrapImminentStop	1.3.6.1.4.1.4555.1.1.1.2.0.10			SEVERE: The UPS is near to switch off the output power.
NTF upsTrapTurnedOff	1.3.6.1.4.1.4555.1.1.1.2.0.11			WARNING: The UPS has been turned off by the management station.
NTF upsTrapOverTemperature	1.3.6.1.4.1.4555.1.1.1.2.0.12			SEVERE: The UPS has sensed a temperature greater than its limit.
NTF upsTrapOverload	1.3.6.1.4.1.4555.1.1.1.2.0.13			SEVERE: The UPS has sensed a load greater than 100 percent of its rated capacity.
NTF upsTrapOnMains	1.3.6.1.4.1.4555.1.1.1.2.0.14			SEVERE: The UPS output is on mains.
NTF upsTrapRedoundancyLost	1.3.6.1.4.1.4555.1.1.1.2.0.15			SEVERE: Redoundancy is lost.
NTF upsTrapEmdTempLow	1.3.6.1.4.1.4555.1.1.1.2.0.16			SEVERE: EMD Sensor detected low temperature.
NTF upsTrapEmdTempHigh	1.3.6.1.4.1.4555.1.1.1.2.0.17			SEVERE: EMD Sensor detected high temperature.
NTF upsTrapEmdHumidityLow	1.3.6.1.4.1.4555.1.1.1.2.0.18			SEVERE: EMD Sensor detected low humidity.
NTF upsTrapEmdHumidityHigh	1.3.6.1.4.1.4555.1.1.1.2.0.19			SEVERE: EMD Sensor detected high humidity.
NTF upsTrapEmdFirstInputActive	1.3.6.1.4.1.4555.1.1.1.2.0.20			SEVERE: The input is active.
NTF upsTrapEmdFirstInputRestored	1.3.6.1.4.1.4555.1.1.1.2.0.21			INFORMATION: The input is restored.
NTF upsTrapEmdSecondInputActive	1.3.6.1.4.1.4555.1.1.1.2.0.22			SEVERE: The input is active.
NTF upsTrapEmdSecondInputRestored	1.3.6.1.4.1.4555.1.1.1.2.0.23			INFORMATION: The input is restored.

RFC description

Vendor-specific MIB for Socomec UPS (uninterruptible power supply) systems; defines objects for power monitoring and battery status.

Start monitoring Socomec UPS, power protection equipment (battery/input-output/alarm status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SOCOMECUPS-MIB

What Is SOCOMECUPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description