SLE-MPLS-TP-NODE-MIB

All MIBs › SLE-MPLS-TP-NODE-MIB

Organization: Multiprotocol Label Switching (MPLS) Working Group

Last Updated: 2015-10-07

Category: DASAN Networks SLE OLT Management, MPLS Transport Profile

Description: Manages DASAN Networks SLE OLT MPLS-TP node identity, global configuration, and MEP addressing.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SLE-MPLS-TP-NODE-MIB?

SLE-MPLS-TP-NODE-MIB is a DASAN Networks MIB used on their SLE OLT (optical line terminal) platform, covering MPLS Transport Profile (MPLS-TP) node identity, global configuration, and Maintenance Entity Group End Point (MEP) addressing for MPLS-TP-based transport networks. It exposes configuration data identifying the local MPLS-TP node (its global node ID and related identifiers) and settings for MEPs used in MPLS-TP OAM (operations, administration, and maintenance). Its monitoring role centers on configuration and topology verification for MPLS-TP transport connections rather than classic hardware sensors, letting an administrator confirm the node identity and MEP addressing that OAM continuity-check and fault-detection mechanisms rely on. The module description indicates it is derived from IETF MPLS Traffic Engineering conventions, so it depends conceptually on the broader IETF MPLS-TE/MPLS-TP MIB framework even though this instance is DASAN-specific. It is deployed on DASAN SLE OLT platforms participating in carrier MPLS-TP transport networks, typically in access/aggregation network segments carrying Ethernet or TDM pseudowire traffic over MPLS-TP tunnels, and the SLE-MPLS-TP-NODE-MIB MIB is what documents the node and MEP identifiers those OAM sessions depend on.

IPNetwork Monitor allows you to monitor SNMP objects defined in SLE-MPLS-TP-NODE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

DASAN Networks SLE OLT

Monitoring Examples

No sample objects were extracted for this module in the source, so specific object names cannot be confirmed, but based on its stated purpose an administrator would typically read the node's global MPLS-TP node identifier and per-MEP addressing configuration to confirm that OAM endpoints are correctly provisioned before or during MPLS-TP OAM fault detection. An incorrectly configured node ID or MEP address would prevent OAM continuity-check messages from correlating properly, masking real transport-path faults.

What Can Be Monitored

MPLS-TP node identifier
MEP (Maintenance Entity Group End Point) addressing
global MPLS-TP configuration

Imported Objects

From DASAN-SMI

sleMgmt

OBJECT-IDENTITY

From MPLS-TE-STD-MIB

mplsTunnelEgressLSRId	OBJECT-TYPE
mplsTunnelIndex	OBJECT-TYPE
mplsTunnelIngressLSRId	OBJECT-TYPE
mplsTunnelInstance	OBJECT-TYPE

From SLE-TC-MIB

SleControlRequestResultType
SleControlStatusType

From SNMPv2-SMI

Gauge32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32
zeroDotZero

OIDs

OID symbolic	OID numeric	Type	Access	Description
sleMpls	1.3.6.1.4.1.6296.101.16			SLE MPLS.
sleMplsTpNode	1.3.6.1.4.1.6296.101.16.13			Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This MIB module contains generic object definitions for MPLS Traffic Engineering in transport networks.
sleMplsTpNodeCfg	1.3.6.1.4.1.6296.101.16.13.1
sleMplsTpNodeCfgInfo	1.3.6.1.4.1.6296.101.16.13.1.1
U32 sleMplsTpNodeCfgInfoGlobalId	1.3.6.1.4.1.6296.101.16.13.1.1.1	Unsigned32	read-only	This object indicates the Global Operator Identifier. this object value should be zero when sleMplsTpNodeConfigInfoCcId and sleMplsTpNodeConfigInfoICcId is configured with non-null value.
MPL sleMplsTpNodeCfgInfoItutCc	1.3.6.1.4.1.6296.101.16.13.1.1.2	MplsCcId	read-only	This object allows the operator or service provider to configure a unique MPLS-TP ITU-T Carrier Code (ICC) either for Ingress ID or Egress ID. This object value should be zero when sleMplsTpNodeConfigInfoGlobalId are assigned with non-zero value.
MPL sleMplsTpNodeCfgInfoItutIcc	1.3.6.1.4.1.6296.101.16.13.1.1.3	MplsIccId	read-only	This object allows the operator or service provider to configure a unique MPLS-TP ITU-T Carrier Code (ICC) either for Ingress ID or Egress ID. This object value should be zero when sleMplsTpNodeConfigInfoGlobalId are assigned with non-zero value.
IP sleMplsTpNodeCfgInfoNodeId	1.3.6.1.4.1.6296.101.16.13.1.1.4	IpAddress	read-only	This object indicates the Node_ID within the operator.
INT sleMplsTpNodeCfgInfoNodeType	1.3.6.1.4.1.6296.101.16.13.1.1.5	INTEGER	read-only	This object value should be zero when sleMplsTpNodeConfigInfoGlobalId are assigned with non-zero value .
sleMplsTpNodeCfgControl	1.3.6.1.4.1.6296.101.16.13.1.2
INT sleMplsTpNodeCfgControlRequest	1.3.6.1.4.1.6296.101.16.13.1.2.1	INTEGER	read-write	This object holds the possible read-write columns that can be modified in the TunnelExtNodeConfigTable table. For each read-write column of TunnelExtNodeConfigTable table, a Set Operation control value is added in this object.
SLE sleMplsTpNodeCfgControlStatus	1.3.6.1.4.1.6296.101.16.13.1.2.2	SleControlStatusType	read-only	This object displays the status of the configuration done.
G32 sleMplsTpNodeCfgControlTimer	1.3.6.1.4.1.6296.101.16.13.1.2.3	Gauge32	read-write	This object is based on the SLE style where a timer is configured for every control table.
TIK sleMplsTpNodeCfgControlTimestamp	1.3.6.1.4.1.6296.101.16.13.1.2.4	TimeTicks	read-only	This object specifies the time at which the configuration is done.
SLE sleMplsTpNodeCfgControlReqResult	1.3.6.1.4.1.6296.101.16.13.1.2.5	SleControlRequestResultType	read-only	The standard result of the SET operation is stored here.
U32 sleMplsTpNodeCfgControlGlobalId	1.3.6.1.4.1.6296.101.16.13.1.2.6	Unsigned32	read-write	This object indicates the Global Operator Identifier. This object value should be zero when sleMplsTpNodeConfigControlIccId and sleMplsTpNodeConfigControlccId is configured with non-null value.
MPL sleMplsTpNodeCfgControlItutCc	1.3.6.1.4.1.6296.101.16.13.1.2.7	MplsCcId	read-write	This object allows the operator or service provider to configure a unique MPLS-TP ITU-T Carrier Code (ICC) either for Ingress ID or Egress ID. This object value should be zero when sleMplsTpNodeConfigControlGlobalId are assigned with non-zero value.
MPL sleMplsTpNodeCfgControlItutIcc	1.3.6.1.4.1.6296.101.16.13.1.2.8	MplsIccId	read-write	This object allows the operator or service provider to configure a unique MPLS-TP ITU-T Carrier Code (ICC) either for Ingress ID or Egress ID. This object value should be zero when sleMplsTpNodeConfigControlGlobalId are assigned with non-zero value.
IP sleMplsTpNodeCfgControlNodeId	1.3.6.1.4.1.6296.101.16.13.1.2.9	IpAddress	read-write	This object indicates the Node_ID within the operator.
INT sleMplsTpNodeCfgControlNodeType	1.3.6.1.4.1.6296.101.16.13.1.2.10	INTEGER	read-write	This object allows the operator or service provider to configure a unique MPLS-TP ITU-T Carrier Code (ICC) either for Ingress ID or Egress ID. This object value should be zero when msleMplsTpNodeConfigControlGlobalId are assigned with non-zero value.

RFC description

MPLS Traffic Engineering node configuration and management for transport networks.

Start monitoring DASAN Networks SLE OLT (MPLS-TP node identity/MEP addressing configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SLE-MPLS-TP-NODE-MIB

What Is SLE-MPLS-TP-NODE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description