SL10-MIB

All MIBs › SL10-MIB

Category: Asentria Remote Site Monitoring, Building and Environmental Control

Description: Manages SL10-series remote site monitoring device for environmental sensors and alarm reporting.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SL10-MIB?

SL10-MIB is a vendor MIB for the SL10-series remote site monitoring device, used to watch environmental sensors and generate alarms at unattended sites, similar in purpose to the Asentria SiteBoss family. Its data covers device identity/software information (serial number, firmware version, site ID), sensor input configuration, and alarm/trap state, giving it both an inventory and an environmental-fault monitoring role. For hardware/software status monitoring it exposes firmwareVersion for confirming the installed software level, serialNumber and siteID for inventory tracking, and alarmStatus plus configurable trap destinations (snmpManager1-4) and custom trap text (thisTrapText) for alarm delivery, making it useful both for asset tracking and for real-time fault notification. It appears to be a self-contained vendor MIB with no explicit external MIB dependency indicated by its objects. It is deployed at unattended remote sites (huts, cabinets, cell sites), where SL10-MIB SNMP monitoring provides basic environmental sensing and trap-based alerting.

IPNetwork Monitor allows you to monitor SNMP objects defined in SL10-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SL10-series remote site monitoring device

Monitoring Examples

An operator would poll firmwareVersion and serialNumber to confirm the correct software revision is running on a given SL10 unit during an inventory audit, and check siteID to identify which physical location the unit belongs to. The input78Mode object configures how a specific sensor input is interpreted, and alarmStatus reflects whether any configured condition is currently active. When a condition trips, forceTraps and thisTrapText control whether and what custom message is sent to the configured snmpManager1 through snmpManager4 destinations.

What Can Be Monitored

firmware version
serial number and site ID
alarm status
sensor input mode configuration
trap destination configuration (up to 4 managers)
custom trap text/forced trap generation

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
TimeTicks
enterprises
internet
mgmt
private

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
asentria	1.3.6.1.4.1.3052
sl10	1.3.6.1.4.1.3052.40
NTF contact1ActiveTrap	1.3.6.1.4.1.3052.40.0.20001			Sent to show Contact 1 is in the alarm state
NTF contact2ActiveTrap	1.3.6.1.4.1.3052.40.0.20002			Sent to show Contact 2 is in the alarm state
NTF contact3ActiveTrap	1.3.6.1.4.1.3052.40.0.20003			Sent to show Contact 3 is in the alarm state
NTF contact4ActiveTrap	1.3.6.1.4.1.3052.40.0.20004			Sent to show Contact 4 is in the alarm state
NTF contact5ActiveTrap	1.3.6.1.4.1.3052.40.0.20005			Sent to show Contact 5 is in the alarm state
NTF contact6ActiveTrap	1.3.6.1.4.1.3052.40.0.20006			Sent to show Contact 6 is in the alarm state
NTF contact7ActiveTrap	1.3.6.1.4.1.3052.40.0.20007			Sent to show Contact 7 is in the alarm state
NTF contact8ActiveTrap	1.3.6.1.4.1.3052.40.0.20008			Sent to show Contact 8 is in the alarm state
NTF contact9ActiveTrap	1.3.6.1.4.1.3052.40.0.20009			Send to show Contact 9 is in the alarm state
NTF tempHighTrap	1.3.6.1.4.1.3052.40.0.20010			Sent to show Temp exceeded High Temp Threshold
NTF tempVeryHighTrap	1.3.6.1.4.1.3052.40.0.20011			Sent to show Temp exceeded Very High Temp Threshold
NTF tempLowTrap	1.3.6.1.4.1.3052.40.0.20012			Sent to show Temp went below Low Temp Threshold
NTF tempVeryLowTrap	1.3.6.1.4.1.3052.40.0.20013			Sent to show Temp went below Very Low Temp Threshold
NTF humidityHighTrap	1.3.6.1.4.1.3052.40.0.20020			Sent to show humidity exceeded High humidity Threshold
NTF humidityVeryHighTrap	1.3.6.1.4.1.3052.40.0.20021			Sent to show humidity exceeded Very High humidity Threshold
NTF humidityLowTrap	1.3.6.1.4.1.3052.40.0.20022			Sent to show humidity went below Low humidity Threshold
NTF humidityVeryLowTrap	1.3.6.1.4.1.3052.40.0.20023			Sent to show humidity went below Very Low humidity Threshold
NTF analog1HighTrap	1.3.6.1.4.1.3052.40.0.20030			Sent to show analog1 exceeded High analog1 Threshold
NTF analog1VeryHighTrap	1.3.6.1.4.1.3052.40.0.20031			Sent to show analog1 exceeded Very High analog1 Threshold
NTF analog1LowTrap	1.3.6.1.4.1.3052.40.0.20032			Sent to show analog1 went below Low analog1 Threshold
NTF analog1VeryLowTrap	1.3.6.1.4.1.3052.40.0.20033			Sent to show analog1 went below Very Low analog1 Threshold
NTF analog2HighTrap	1.3.6.1.4.1.3052.40.0.20040			Sent to show analog2 exceeded High analog2 Threshold
NTF analog2VeryHighTrap	1.3.6.1.4.1.3052.40.0.20041			Sent to show analog2 exceeded Very High analog2 Threshold
NTF analog2LowTrap	1.3.6.1.4.1.3052.40.0.20042			Sent to show analog2 went below Low analog2 Threshold
NTF analog2VeryLowTrap	1.3.6.1.4.1.3052.40.0.20043			Sent to show analog2 went below Very Low analog2 Threshold
NTF contactESActiveTrap	1.3.6.1.4.1.3052.40.0.20101			Sent to show EventSensor contact is in the alarm state
NTF tempESHighTrap	1.3.6.1.4.1.3052.40.0.20110			Sent to show Temp exceeded High Threshold on an EventSensor
NTF tempESVeryHighTrap	1.3.6.1.4.1.3052.40.0.20111			Sent to show Temp exceeded Very High Threshold on an EventSensor
NTF tempESLowTrap	1.3.6.1.4.1.3052.40.0.20112			Sent to show Temp went below Low Threshold on an EventSensor
NTF tempESVeryLowTrap	1.3.6.1.4.1.3052.40.0.20113			Sent to show Temp went below Very Low Threshold on an EventSensor
NTF humidityESHighTrap	1.3.6.1.4.1.3052.40.0.20120			Sent to show humidity exceeded High Threshold on an EventSensor
NTF humidityESVeryHighTrap	1.3.6.1.4.1.3052.40.0.20121			Sent to show humidity exceeded Very High Threshold on an EventSensor
NTF humidityESLowTrap	1.3.6.1.4.1.3052.40.0.20122			Sent to show humidity went below Low Threshold on an EventSensor
NTF humidityESVeryLowTrap	1.3.6.1.4.1.3052.40.0.20123			Sent to show humidity went below Very Low Threshold on an EventSensor
NTF voltageESHighTrap	1.3.6.1.4.1.3052.40.0.20130			Sent to show voltage exceeded High Threshold on an EventSensor
NTF voltageESVeryHighTrap	1.3.6.1.4.1.3052.40.0.20131			Sent to show voltage exceeded Very High Threshold on an EventSensor
NTF voltageESLowTrap	1.3.6.1.4.1.3052.40.0.20132			Sent to show voltage went below Low Threshold on an EventSensor
NTF voltageESVeryLowTrap	1.3.6.1.4.1.3052.40.0.20133			Sent to show voltage went below Very Low Threshold on an EventSensor
NTF contact1NormalTrap	1.3.6.1.4.1.3052.40.0.21001			Sent to show Contact 1 is in the normal state
NTF contact2NormalTrap	1.3.6.1.4.1.3052.40.0.21002			Sent to show Contact 2 is in the normal state
NTF contact3NormalTrap	1.3.6.1.4.1.3052.40.0.21003			Sent to show Contact 3 is in the normal state
NTF contact4NormalTrap	1.3.6.1.4.1.3052.40.0.21004			Sent to show Contact 4 is in the normal state
NTF contact5NormalTrap	1.3.6.1.4.1.3052.40.0.21005			Sent to show Contact 5 is in the normal state
NTF contact6NormalTrap	1.3.6.1.4.1.3052.40.0.21006			Sent to show Contact 6 is in the normal state
NTF contact7NormalTrap	1.3.6.1.4.1.3052.40.0.21007			Sent to show Contact 7 is in the normal state
NTF contact8NormalTrap	1.3.6.1.4.1.3052.40.0.21008			Sent to show Contact 8 is in the normal state
NTF contact9NormalTrap	1.3.6.1.4.1.3052.40.0.21009			Send to show Contact 9 is in the normal state
NTF tempNormalTrap	1.3.6.1.4.1.3052.40.0.21010			Sent to show Temp went back to Normal range
NTF humidityNormalTrap	1.3.6.1.4.1.3052.40.0.21020			Sent to show Humidity went back to Normal range
NTF analog1NormalTrap	1.3.6.1.4.1.3052.40.0.21030			Sent to show analog1 went back to Normal range
NTF analog2NormalTrap	1.3.6.1.4.1.3052.40.0.21040			Sent to show analog2 went back to Normal range
NTF contactESNormalTrap	1.3.6.1.4.1.3052.40.0.21101			Send to show EventSensor contact has returned to normal state
NTF tempESNormalTrap	1.3.6.1.4.1.3052.40.0.21110			Sent to show EventSensor Temp went back to Normal range
NTF humidityESNormalTrap	1.3.6.1.4.1.3052.40.0.21120			Sent to show EventSensor Humidity went back to Normal range
NTF voltageESNormalTrap	1.3.6.1.4.1.3052.40.0.21130			Sent to show EventSensor voltage went back to Normal range
NTF testTrap	1.3.6.1.4.1.3052.40.0.22000			Sent for testing the SNMP interface
device	1.3.6.1.4.1.3052.40.1
STR serialNumber	1.3.6.1.4.1.3052.40.1.1	DisplayString	read-only	8-character serial number
STR firmwareVersion	1.3.6.1.4.1.3052.40.1.2	DisplayString	read-only	Firmware version text string
STR siteID	1.3.6.1.4.1.3052.40.1.3	DisplayString	read-write	Site Identifier, up to 12 characters.
IP snmpManager	1.3.6.1.4.1.3052.40.1.4	IpAddress	read-write	This is snmp manager #1
INT input78Mode	1.3.6.1.4.1.3052.40.1.5	INTEGER	read-only	Mode of operation of inputs 7/8. 0-analog 1&2 =default, 1-contacts 7&8
INT forceTraps	1.3.6.1.4.1.3052.40.1.6	INTEGER	read-write	Any write non-zero forces set of traps to be send to the SNMP Manager
STR thisTrapText	1.3.6.1.4.1.3052.40.1.7	DisplayString	read-write	A text string included in all traps
STR alarmStatus	1.3.6.1.4.1.3052.40.1.8	DisplayString	read-only	A text status of all alarms
IP snmpManager1	1.3.6.1.4.1.3052.40.1.9	IpAddress	read-write	SNMP manager #1
IP snmpManager2	1.3.6.1.4.1.3052.40.1.10	IpAddress	read-write	SNMP manager #2
IP snmpManager3	1.3.6.1.4.1.3052.40.1.11	IpAddress	read-write	SNMP manager #3
IP snmpManager4	1.3.6.1.4.1.3052.40.1.12	IpAddress	read-write	SNMP manager #4
INT statusRepeatHours	1.3.6.1.4.1.3052.40.1.13	INTEGER	read-write	0=none, 1-24 Number of Hours between Status Traps being Sent
INT serialTimeout	1.3.6.1.4.1.3052.40.1.14	INTEGER	read-write	5-30, Minutes of non-activity timeout on serial setup
INT powerupTrapsend	1.3.6.1.4.1.3052.40.1.15	INTEGER	read-write	0-no, 1-yes, send traps for all sensors on powerup
INT netlossTrapsend	1.3.6.1.4.1.3052.40.1.16	INTEGER	read-write	0-no, 1-yes, send traps for detected netloss and back up
STR buildID	1.3.6.1.4.1.3052.40.1.17	DisplayString	read-only	5-chars max text for build identifier
contacts	1.3.6.1.4.1.3052.40.2
contact1	1.3.6.1.4.1.3052.40.2.1
STR contact1Name	1.3.6.1.4.1.3052.40.2.1.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact1State	1.3.6.1.4.1.3052.40.2.1.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact1AlarmEnable	1.3.6.1.4.1.3052.40.2.1.3	INTEGER	read-write	0-alarms disabled 1-alarms enabled
INT contact1ActiveDirection	1.3.6.1.4.1.3052.40.2.1.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact1Threshold	1.3.6.1.4.1.3052.40.2.1.5	INTEGER	read-write	Number of seconds that the contact must remain in a state before generating a trap, range 0-255
INT contact1ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.1.6	INTEGER	read-write	0-return to normal traps not sent, 1-sent
INT contact1TrapRepeat	1.3.6.1.4.1.3052.40.2.1.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps.
INT contact1Severity	1.3.6.1.4.1.3052.40.2.1.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact2	1.3.6.1.4.1.3052.40.2.2
STR contact2Name	1.3.6.1.4.1.3052.40.2.2.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact2State	1.3.6.1.4.1.3052.40.2.2.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact2AlarmEnable	1.3.6.1.4.1.3052.40.2.2.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact2ActiveDirection	1.3.6.1.4.1.3052.40.2.2.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact2Threshold	1.3.6.1.4.1.3052.40.2.2.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact2ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.2.6	INTEGER	read-write	0-not sent, 1-sent
INT contact2TrapRepeat	1.3.6.1.4.1.3052.40.2.2.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps
INT contact2Severity	1.3.6.1.4.1.3052.40.2.2.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact3	1.3.6.1.4.1.3052.40.2.3
STR contact3Name	1.3.6.1.4.1.3052.40.2.3.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact3State	1.3.6.1.4.1.3052.40.2.3.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact3AlarmEnable	1.3.6.1.4.1.3052.40.2.3.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact3ActiveDirection	1.3.6.1.4.1.3052.40.2.3.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact3Threshold	1.3.6.1.4.1.3052.40.2.3.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact3ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.3.6	INTEGER	read-write	0-not sent, 1-sent
INT contact3TrapRepeat	1.3.6.1.4.1.3052.40.2.3.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps
INT contact3Severity	1.3.6.1.4.1.3052.40.2.3.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact4	1.3.6.1.4.1.3052.40.2.4
STR contact4Name	1.3.6.1.4.1.3052.40.2.4.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact4State	1.3.6.1.4.1.3052.40.2.4.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact4AlarmEnable	1.3.6.1.4.1.3052.40.2.4.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact4ActiveDirection	1.3.6.1.4.1.3052.40.2.4.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact4Threshold	1.3.6.1.4.1.3052.40.2.4.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact4ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.4.6	INTEGER	read-write	0-not sent, 1-sent
INT contact4TrapRepeat	1.3.6.1.4.1.3052.40.2.4.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps
INT contact4Severity	1.3.6.1.4.1.3052.40.2.4.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact5	1.3.6.1.4.1.3052.40.2.5
STR contact5Name	1.3.6.1.4.1.3052.40.2.5.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact5State	1.3.6.1.4.1.3052.40.2.5.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact5AlarmEnable	1.3.6.1.4.1.3052.40.2.5.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact5ActiveDirection	1.3.6.1.4.1.3052.40.2.5.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact5Threshold	1.3.6.1.4.1.3052.40.2.5.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact5ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.5.6	INTEGER	read-write	0-not sent, 1-sent
INT contact5TrapRepeat	1.3.6.1.4.1.3052.40.2.5.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps
INT contact5Severity	1.3.6.1.4.1.3052.40.2.5.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact6	1.3.6.1.4.1.3052.40.2.6
STR contact6Name	1.3.6.1.4.1.3052.40.2.6.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact6State	1.3.6.1.4.1.3052.40.2.6.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact6AlarmEnable	1.3.6.1.4.1.3052.40.2.6.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact6ActiveDirection	1.3.6.1.4.1.3052.40.2.6.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact6Threshold	1.3.6.1.4.1.3052.40.2.6.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact6ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.6.6	INTEGER	read-write	0-not sent, 1-sent
INT contact6TrapRepeat	1.3.6.1.4.1.3052.40.2.6.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps.
INT contact6Severity	1.3.6.1.4.1.3052.40.2.6.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact7	1.3.6.1.4.1.3052.40.2.7
STR contact7Name	1.3.6.1.4.1.3052.40.2.7.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact7State	1.3.6.1.4.1.3052.40.2.7.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact7AlarmEnable	1.3.6.1.4.1.3052.40.2.7.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact7ActiveDirection	1.3.6.1.4.1.3052.40.2.7.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact7Threshold	1.3.6.1.4.1.3052.40.2.7.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact7ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.7.6	INTEGER	read-write	0-not sent, 1-sent
INT contact7TrapRepeat	1.3.6.1.4.1.3052.40.2.7.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps
INT contact7Severity	1.3.6.1.4.1.3052.40.2.7.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact8	1.3.6.1.4.1.3052.40.2.8
STR contact8Name	1.3.6.1.4.1.3052.40.2.8.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact8State	1.3.6.1.4.1.3052.40.2.8.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact8AlarmEnable	1.3.6.1.4.1.3052.40.2.8.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact8ActiveDirection	1.3.6.1.4.1.3052.40.2.8.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact8Threshold	1.3.6.1.4.1.3052.40.2.8.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact8ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.8.6	INTEGER	read-write	0-not sent, 1-sent
INT contact8TrapRepeat	1.3.6.1.4.1.3052.40.2.8.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps
INT contact8Severity	1.3.6.1.4.1.3052.40.2.8.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
contact9	1.3.6.1.4.1.3052.40.2.9
STR contact9Name	1.3.6.1.4.1.3052.40.2.9.1	DisplayString	read-write	Name for contact, up to 30 characters
INT contact9State	1.3.6.1.4.1.3052.40.2.9.2	INTEGER	read-only	Current State of Contact, 0-open 1-closed
INT contact9AlarmEnable	1.3.6.1.4.1.3052.40.2.9.3	INTEGER	read-write	0-no alarms 1-alarms enabled
INT contact9ActiveDirection	1.3.6.1.4.1.3052.40.2.9.4	INTEGER	read-write	0-alarm on open 1-alarm on closed
INT contact9Threshold	1.3.6.1.4.1.3052.40.2.9.5	INTEGER	read-write	Number of seconds must be in a state to be 'open' or 'closed'
INT contact9ReturnNormalTrap	1.3.6.1.4.1.3052.40.2.9.6	INTEGER	read-write	0-not sent, 1-sent
INT contact9TrapRepeat	1.3.6.1.4.1.3052.40.2.9.7	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps
INT contact9Severity	1.3.6.1.4.1.3052.40.2.9.8	INTEGER	read-write	1-minor 2-major 3-critical 4-severe 5-warning
relays	1.3.6.1.4.1.3052.40.3
relay1	1.3.6.1.4.1.3052.40.3.1
STR relay1Name	1.3.6.1.4.1.3052.40.3.1.1	DisplayString	read-write	Name for relay, up to 30 characters
INT relay1CurrentState	1.3.6.1.4.1.3052.40.3.1.2	INTEGER	read-write	0-opened, 1-closed
INT relay1PowerupState	1.3.6.1.4.1.3052.40.3.1.3	INTEGER	read-write	0-opened, 1-closed
relay2	1.3.6.1.4.1.3052.40.3.2
STR relay2Name	1.3.6.1.4.1.3052.40.3.2.1	DisplayString	read-write	Name for relay, up to 30 characters
INT relay2CurrentState	1.3.6.1.4.1.3052.40.3.2.2	INTEGER	read-write	0-opened, 1-closed
INT relay2PowerupState	1.3.6.1.4.1.3052.40.3.2.3	INTEGER	read-write	0-opened, 1-closed
tempsensor	1.3.6.1.4.1.3052.40.4
INT tempValue	1.3.6.1.4.1.3052.40.4.1	INTEGER	read-only	Current Temperature Value, in C or F based on 1.3.6.1.4.1.3052.40.4.10
INT tempAlarmEnable	1.3.6.1.4.1.3052.40.4.2	INTEGER	read-write	0=alarms disabled, 1=alarms enabled
INT tempHighLevel	1.3.6.1.4.1.3052.40.4.3	INTEGER	read-write	Level at which the High alarm goes active
INT tempVeryHighLevel	1.3.6.1.4.1.3052.40.4.4	INTEGER	read-write	Level at which the Very High alarm goes active
INT tempLowLevel	1.3.6.1.4.1.3052.40.4.5	INTEGER	read-write	Level at which the Low alarm goes active
INT tempVeryLowLevel	1.3.6.1.4.1.3052.40.4.6	INTEGER	read-write	Level at which the Very Low alarm goes active
INT tempAlarmThreshold	1.3.6.1.4.1.3052.40.4.7	INTEGER	read-write	Seconds must be in a range to be an alarm
INT tempReturnNormalTrap	1.3.6.1.4.1.3052.40.4.8	INTEGER	read-write	0-not sent, 1-send trap on return to normal range
INT tempTrapRepeat	1.3.6.1.4.1.3052.40.4.9	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps.
INT tempMode	1.3.6.1.4.1.3052.40.4.10	INTEGER	read-write	0=all temp readings and levels in degrees F, 1=in degrees C
INT tempHighSeverity	1.3.6.1.4.1.3052.40.4.11	INTEGER	read-write	High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT tempVeryHighSeverity	1.3.6.1.4.1.3052.40.4.12	INTEGER	read-write	Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT tempLowSeverity	1.3.6.1.4.1.3052.40.4.13	INTEGER	read-write	Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT tempVeryLowSeverity	1.3.6.1.4.1.3052.40.4.14	INTEGER	read-write	Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
STR tempName	1.3.6.1.4.1.3052.40.4.15	DisplayString	read-write	Name for temperature sensor, up to 30 characters
humiditysensor	1.3.6.1.4.1.3052.40.5
INT humidityValue	1.3.6.1.4.1.3052.40.5.1	INTEGER	read-only	Current Relative Humidity Value (0-100%)
INT humidityAlarmEnable	1.3.6.1.4.1.3052.40.5.2	INTEGER	read-write	0=alarms disabled, 1=alarms enabled
INT humidityHighLevel	1.3.6.1.4.1.3052.40.5.3	INTEGER	read-write	Level at which the High alarm goes active
INT humidityVeryHighLevel	1.3.6.1.4.1.3052.40.5.4	INTEGER	read-write	Level at which the Very High alarm goes active
INT humidityLowLevel	1.3.6.1.4.1.3052.40.5.5	INTEGER	read-write	Level at which the Low alarm goes active
INT humidityVeryLowLevel	1.3.6.1.4.1.3052.40.5.6	INTEGER	read-write	Level at which the Very Low alarm goes active
INT humidityAlarmThreshold	1.3.6.1.4.1.3052.40.5.7	INTEGER	read-write	Seconds must be in a range to be an alarm
INT humidityReturnNormalTrap	1.3.6.1.4.1.3052.40.5.8	INTEGER	read-write	0-not sent, 1-send trap on return to normal range
INT humidityTrapRepeat	1.3.6.1.4.1.3052.40.5.9	INTEGER	read-write	0-no repeats. 1-255 number of minutes between repeats of alarm traps.
INT humidityHighSeverity	1.3.6.1.4.1.3052.40.5.10	INTEGER	read-write	High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT humidityVeryHighSeverity	1.3.6.1.4.1.3052.40.5.11	INTEGER	read-write	Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT humidityLowSeverity	1.3.6.1.4.1.3052.40.5.12	INTEGER	read-write	Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT humidityVeryLowSeverity	1.3.6.1.4.1.3052.40.5.13	INTEGER	read-write	Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
STR humidityName	1.3.6.1.4.1.3052.40.5.14	DisplayString	read-write	Name for humidity sensor, up to 30 characters
passthrough	1.3.6.1.4.1.3052.40.6
INT ptNeedPassword	1.3.6.1.4.1.3052.40.6.1	INTEGER	read-write	0-no 1-yes, is password required for passthrough connection.
INT ptSayLoginText	1.3.6.1.4.1.3052.40.6.2	INTEGER	read-write	0-no 1-yes, is passthrough login text displayed on connection.
STR ptLoginText	1.3.6.1.4.1.3052.40.6.3	DisplayString	read-write	0-24 char string which may be displayed on socket connection. Requires that ptSayLoginText be enabled to display this string.
INT ptSaySiteID	1.3.6.1.4.1.3052.40.6.4	INTEGER	read-write	0-no 1-yes, is SiteID displayed on pass through connection.
STR ptUsername	1.3.6.1.4.1.3052.40.6.5	DisplayString	read-write	0-16 char string for Username used in serial passthrough connections
STR ptPassword	1.3.6.1.4.1.3052.40.6.6	DisplayString	read-write	0-16 char string for Password used in serial passthrough connections
INT ptTimeout	1.3.6.1.4.1.3052.40.6.7	INTEGER	read-write	number of minutes (1-255) of idle activity (both directions) which causes disconnect. 0-never
INT ptEscChar	1.3.6.1.4.1.3052.40.6.8	INTEGER	read-write	ASCII character code (e.g, Escape=27) which if entered on the tcp port three times in a row causes disconnect. 0-none
INT ptLfstripToPort	1.3.6.1.4.1.3052.40.6.9	INTEGER	read-write	0-no 1-yes linefeed characters received on TCP connection are removed from stream to serial port
INT ptLfstripFromPort	1.3.6.1.4.1.3052.40.6.10	INTEGER	read-write	0-no 1-yes linefeed characters received on serial port are removed from stream to TCP connection
INT ptSerialBaudrate	1.3.6.1.4.1.3052.40.6.11	INTEGER	read-write	300 600 1200 2400 4800 9600 19200 baud are allowed values
INT ptSerialWordlength	1.3.6.1.4.1.3052.40.6.12	INTEGER	read-write	7 or 8 bit word selection
STR ptSerialParity	1.3.6.1.4.1.3052.40.6.13	DisplayString	read-write	N E O are allowed values for parity (none, even, odd) [a single-character string]
INT ptTCPPortnumber	1.3.6.1.4.1.3052.40.6.14	INTEGER	read-write	IP port number for passthrough connection (range 1024-65534)
ftp	1.3.6.1.4.1.3052.40.7
STR ftpUsername	1.3.6.1.4.1.3052.40.7.1	DisplayString	read-write	0-16 char string for Username used in ftp server for updates
STR ftpPassword	1.3.6.1.4.1.3052.40.7.2	DisplayString	read-write	0-16 char string for Password used in ftp server for updates
analog	1.3.6.1.4.1.3052.40.8
analog1	1.3.6.1.4.1.3052.40.8.1
INT analog1Value	1.3.6.1.4.1.3052.40.8.1.1	INTEGER	read-only	Value of current analog reading, in 1/100 volt, +- 9999 range
INT analog1AlarmEnable	1.3.6.1.4.1.3052.40.8.1.2	INTEGER	read-write	0=no alarms, 1=send alarms
INT analog1HighLevel	1.3.6.1.4.1.3052.40.8.1.3	INTEGER	read-write	Level at which the High alarm goes active
INT analog1VeryHighLevel	1.3.6.1.4.1.3052.40.8.1.4	INTEGER	read-write	Level at which the Very High alarm goes active
INT analog1LowLevel	1.3.6.1.4.1.3052.40.8.1.5	INTEGER	read-write	Level at which the Low alarm goes active
INT analog1VeryLowLevel	1.3.6.1.4.1.3052.40.8.1.6	INTEGER	read-write	Level at which the Very Low alarm goes active
INT analog1AlarmThreshold	1.3.6.1.4.1.3052.40.8.1.7	INTEGER	read-write	Seconds must be in a range to be an alarm
INT analog1ReturnNormalTrap	1.3.6.1.4.1.3052.40.8.1.8	INTEGER	read-write	0-not sent, 1-send trap on return to normal range
INT analog1TrapRepeat	1.3.6.1.4.1.3052.40.8.1.9	INTEGER	read-write	0-no repeats else number of minutes between repeats of trap
INT analog1HighSeverity	1.3.6.1.4.1.3052.40.8.1.10	INTEGER	read-write	High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT analog1VeryHighSeverity	1.3.6.1.4.1.3052.40.8.1.11	INTEGER	read-write	Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT analog1LowSeverity	1.3.6.1.4.1.3052.40.8.1.12	INTEGER	read-write	Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT analog1VeryLowSeverity	1.3.6.1.4.1.3052.40.8.1.13	INTEGER	read-write	Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
STR analog1Name	1.3.6.1.4.1.3052.40.8.1.14	DisplayString	read-write	Name for analog sensor 1, up to 30 characters
analog2	1.3.6.1.4.1.3052.40.8.2
INT analog2Value	1.3.6.1.4.1.3052.40.8.2.1	INTEGER	read-only	Value of current analog reading, in 1/100 volt, +- 9999 range
INT analog2AlarmEnable	1.3.6.1.4.1.3052.40.8.2.2	INTEGER	read-write	0=no alarms, 1=send alarms
INT analog2HighLevel	1.3.6.1.4.1.3052.40.8.2.3	INTEGER	read-write	Level at which the High alarm goes active
INT analog2VeryHighLevel	1.3.6.1.4.1.3052.40.8.2.4	INTEGER	read-write	Level at which the Very High alarm goes active
INT analog2LowLevel	1.3.6.1.4.1.3052.40.8.2.5	INTEGER	read-write	Level at which the Low alarm goes active
INT analog2VeryLowLevel	1.3.6.1.4.1.3052.40.8.2.6	INTEGER	read-write	Level at which the Very Low alarm goes active
INT analog2AlarmThreshold	1.3.6.1.4.1.3052.40.8.2.7	INTEGER	read-write	Seconds must be in a range to be an alarm
INT analog2ReturnNormalTrap	1.3.6.1.4.1.3052.40.8.2.8	INTEGER	read-write	0-not sent, 1-send trap on return to normal range
INT analog2TrapRepeat	1.3.6.1.4.1.3052.40.8.2.9	INTEGER	read-write	0-no repeats else number of minutes between repeats of trap
INT analog2HighSeverity	1.3.6.1.4.1.3052.40.8.2.10	INTEGER	read-write	High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT analog2VeryHighSeverity	1.3.6.1.4.1.3052.40.8.2.11	INTEGER	read-write	Very High Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT analog2LowSeverity	1.3.6.1.4.1.3052.40.8.2.12	INTEGER	read-write	Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
INT analog2VeryLowSeverity	1.3.6.1.4.1.3052.40.8.2.13	INTEGER	read-write	Very Low Level Severity 1-minor 2-major 3-critical 4-severe 5-warning
STR analog2Name	1.3.6.1.4.1.3052.40.8.2.14	DisplayString	read-write	Name for analog sensor 2, up to 30 characters
eventSensorStatus	1.3.6.1.4.1.3052.40.10
esPointTable	1.3.6.1.4.1.3052.40.10.1		not-accessible	This table organizes 4 basic attributes of points. A point is a particular sensor on an EventSensor (e.g., temperature, humidity, contact closure 2, relay 5, etc.). The 4 point attributes are its name, whether it's in its event state, the point's value as a number and its value as a string. Points are referenced by a point index. The point index is a string of 3 numbers separated by periods. It contains all the information necessary for getting a piece of data off an event sensor; namely, which EventSensor, point class, and which-sensor-of-that-class (a.k.a. point).
esPointEntry	1.3.6.1.4.1.3052.40.10.1.1		not-accessible	Entry for EventSensor point table
INT esIndexES	1.3.6.1.4.1.3052.40.10.1.1.1	INTEGER	read-only	The part of the point index that refers to an EventSensor. The point index is a string of 3 numbers separated by periods. It contains all the information necessary for getting a piece of data off an event sensor; namely, which EventSensor, point class, and which-sensor-of-that-class (a.k.a. point). This object's allowable values are 1 through 4, which refer to attached EventSensors. The number corresponding to an EventSensor is determined by the user at the initial configuration time. If there is an internal sensor in the unit, it will always be the first item in the Sensor Events setup menu. For example, if a new EventSensor is configured as the 2nd entry AFTER the internal EventSensor (if one exists) in the Sensor Events Setup Menu, then that EventSensor will be known from then on as EventSensor 2. All point indeces with esIndexES=2 will now refer to that particular EventSensor.
INT esIndexPC	1.3.6.1.4.1.3052.40.10.1.1.2	INTEGER	read-only	The part of the point index that refers to point class. The point index is a string of 3 numbers separated by periods. It contains all the information necessary for getting a piece of data off an event sensor; namely, which EventSensor, point class, and which-sensor-of-that-class (a.k.a. point). The values for this object are: 1=temperature sensor 2=contact closure 3=humidity sensor 4=noise sensor 5=analog input 6=relay
INT esIndexPoint	1.3.6.1.4.1.3052.40.10.1.1.3	INTEGER	read-only	The part of the point index that delineates which sensor on the EventSensor. So this combined with esIndexPC (Point Class or type) and esIndexES (which EventSensor) uniquely defines each point (sensor or relay) attached to a unit. For example, if esIndexES is 3, esIndexPC is 1 and esIndexPoint is 4 then this is the Fourth Temperature Sensor on EventSensor number 3.
STR esPointName	1.3.6.1.4.1.3052.40.10.1.1.4	DisplayString	read-write	The name of the point on an EventSensor. For example, 'AC temp' (in the case of the temperature sensor on an EventSensor). There can be multiple points of the same point class on an EventSensor (e.g., 8 contact closures) and multiple sensor classes on an EventSensor (e.g., temperature, contact closure, humidity). If the point referenced by a given point index is solitary (e.g., temperature sensor, because there can be only one on an EventSensor), then this object reads as ''. Setting this object for solitary point indices sets the EventSensor name only. On the other hand, if a given point is among other points of the same point class on an EventSensor, then this object reads as ''. Setting this object for these NON- solitary point indices sets the sensor name only - not the EventSensor name.
INT esPointInEventState	1.3.6.1.4.1.3052.40.10.1.1.5	INTEGER	read-write	A number referring to the event state of a point on an EventSensor. This number can have different meanings depending on the point class. If the point class is temperature, humidity, or analog input, then the values of this object are: 1=very low 2=low 3=normal 4=high 5=very high For contact closures and relays the values of this object are: 1=point in event state 2=point in normal state For any point class and any point, if the event state is undefined, then the value of this object is 0. For any point class except relay, this object is read-only. For relays, setting this object to 1 puts the relay into its open state. Setting it to 2 puts the relay into its closed state.
INT esPointValueInt	1.3.6.1.4.1.3052.40.10.1.1.6	INTEGER	read-write	A number referring to the value of a point on an EventSensor. If the point class is temperature, then this object is the temperature in its configured scale (default is Fahrenheit). If the point class is contact closure or relay, then this object is either 0 (open) or 1 (closed). If the point class is humidity, then this object is the percent relative humidity. If the point class is analog input, then this object is the signed input value in tenths of the configured units. For any point class except relay, this object is read-only. For relays, setting this object to 1 closes the relay, while setting it to 0 opens it. This works regardless of the control mode of the relay.
STR esPointValueStr	1.3.6.1.4.1.3052.40.10.1.1.7	DisplayString	read-only	A string referring to the value of a point on an EventSensor. For contact closures and relays this object is either 'Open' or 'Closed'. For temperature and humidity point classes, this object is the string representation of the esPointValueInt object. For temperature, 'C' or 'F' is including in the string to indicate scale. For analog inputs, this object is the string representation of the plus/minus input in volts.
eventSensorConfig	1.3.6.1.4.1.3052.40.11
INT esNumberEventSensors	1.3.6.1.4.1.3052.40.11.1	INTEGER	read-only	The number of EventSensors recognized by the SL10 Range: 0-4
esTable	1.3.6.1.4.1.3052.40.11.2		not-accessible	The table of what EventSensors are attached to the unit
esEntry	1.3.6.1.4.1.3052.40.11.2.1		not-accessible	Table entry for EventSensor table
INT esIndex	1.3.6.1.4.1.3052.40.11.2.1.1	INTEGER	read-only	This number refers to an EventSensor; it has the same meaning as the esIndexES object (see above), except that this object is used only within the esTable branch. This object's allowable values are 1 through 4, which refer to additional attached EventSensors. The number corresponding to an EventSensor is determined by the user at the initial configuration time.
STR esID	1.3.6.1.4.1.3052.40.11.2.1.2	DisplayString	read-only	The factory-assigned ID of the EventSensor
INT esNumberTempSensors	1.3.6.1.4.1.3052.40.11.2.1.3	INTEGER	read-only	The number of temperature sensors on the EventSensor
STR esTempReportingMode	1.3.6.1.4.1.3052.40.11.2.1.4	DisplayString	read-only	Description of how temperature values should be interpreted.
INT esNumberCCs	1.3.6.1.4.1.3052.40.11.2.1.5	INTEGER	read-only	The number of contact closures on the EventSensor.
STR esCCReportingMode	1.3.6.1.4.1.3052.40.11.2.1.6	DisplayString	read-only	Description of how CC values should be interpreted.
INT esNumberHumidSensors	1.3.6.1.4.1.3052.40.11.2.1.7	INTEGER	read-only	The number of humidity sensors on the EventSensor.
STR esHumidReportingMode	1.3.6.1.4.1.3052.40.11.2.1.8	DisplayString	read-only	Description of how humidity sensor values should be interpreted.
INT esNumberNoiseSensors	1.3.6.1.4.1.3052.40.11.2.1.9	INTEGER	read-only	The number of noise sensors on the EventSensor.
STR esNoiseReportingMode	1.3.6.1.4.1.3052.40.11.2.1.10	DisplayString	read-only	Description of how noise sensor values should be interpreted.
INT esNumberAirflowSensors	1.3.6.1.4.1.3052.40.11.2.1.11	INTEGER	read-only	The number of airflow sensors on the EventSensor.
STR esAirflowReportingMode	1.3.6.1.4.1.3052.40.11.2.1.12	DisplayString	read-only	Description of how airflow sensor values should be interpreted.
INT esNumberAnalog	1.3.6.1.4.1.3052.40.11.2.1.13	INTEGER	read-only	The number of analog inputs on the EventSensor.
STR esAnalogReportingMode	1.3.6.1.4.1.3052.40.11.2.1.14	DisplayString	read-only	Description of how analog input values should be interpreted.
INT esNumberRelayOutputs	1.3.6.1.4.1.3052.40.11.2.1.15	INTEGER	read-only	The number of relay outputs on the EventSensor
STR esRelayReportingMode	1.3.6.1.4.1.3052.40.11.2.1.16	DisplayString	read-only	Description of how relay output values should be interpreted.
techsupport	1.3.6.1.4.1.3052.40.99
IP techsupportIPAddress	1.3.6.1.4.1.3052.40.99.1	IpAddress	read-write	May read or Set IP Address, takes effect on restart
IP techsupportNetMask	1.3.6.1.4.1.3052.40.99.2	IpAddress	read-write	May read or Set NetMask, takes effect on restart
IP techsupportRouter	1.3.6.1.4.1.3052.40.99.3	IpAddress	read-write	May read or Set Router IP Address, takes effect on restart
INT techsupportRestart	1.3.6.1.4.1.3052.40.99.4	INTEGER	read-write	Reads as 0, any Write resets unit so new IP, Netmask, Router may be used
STR techsupportSerialNumber	1.3.6.1.4.1.3052.40.99.5	DisplayString	read-write	Read/Set Serial Number, up to 8-char text string reported as 1.1
INT techsupportBoxTemp	1.3.6.1.4.1.3052.40.99.6	INTEGER	read-only	Estimate of inside-the-box temp in degrees C, for heater testing
INT techsupportHeaterState	1.3.6.1.4.1.3052.40.99.7	INTEGER	read-only	0-off 1-on (acutal heater pin on/off, heat may not be 100% duty cycle)
INT techsupportPSVolts	1.3.6.1.4.1.3052.40.99.8	INTEGER	read-only	estimate of power supply input voltage (only valid on 48V build)
mibend	1.3.6.1.4.1.3052.40.100
INT mibendObject	1.3.6.1.4.1.3052.40.100.1	INTEGER	read-only	An object after all active mib items, to help some managers compile

RFC description

SNMP MIB for the Omnitronix SNMP-Link SL10 Enclosure Monitoring Unit. Provides management objects for monitoring and controlling enclosure environmental sensors and status.

Start monitoring SL10-series remote site monitoring devices with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SL10-MIB

What Is SL10-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description