SHE-L2CP-MIB

All MIBs › SHE-L2CP-MIB

Organization: Nokia Siemens Networks

Last Updated: 2007-06-06

Description: Nokia Siemens Networks SHE DSLAM Layer 2 Control Protocol interface configuration, alarm severity profiles, and local L2CP host interface VLAN settings

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SHE-L2CP-MIB?

SHE-L2CP-MIB is part of the Nokia Siemens Networks 'SHE' DSLAM MIB suite, covering Layer 2 Control Protocol (L2CP) interface configuration on the hiX5622/5625/5630/5635 family of DSL access multiplexers. It defines configuration for L2CP host interfaces, including VLAN settings, together with alarm severity profiles that control how L2CP-related fault conditions are classified and escalated. Its monitoring relevance is mainly fault/configuration status rather than raw counters: the alarm severity profile settings determine whether an L2CP interface fault is reported as critical, major, or minor to the NMS, and the VLAN configuration confirms control-plane traffic is correctly segregated on the DSLAM's local L2CP host interface. It is one module within the broader NSN SHE DSLAM MIB suite, working alongside SHE-PRODUCTS-MIB (which identifies the specific hardware platform) and other SHE MIBs covering chassis and port management. It is deployed in telecom access networks operating NSN hiX-series DSLAMs, where Layer 2 control-plane configuration and alarm handling need centralized SNMP management. Engineers can download the SHE-L2CP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SHE-L2CP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nokia Siemens Networks hiX5622/5625/5630/5635 DSLAM

Monitoring Examples

No sample runtime objects were captured for this module, so exact identifiers cannot be cited; based on its described scope, an operator would typically configure alarm severity profile objects to control how L2CP interface faults are escalated, and check VLAN settings on the local L2CP host interface to confirm control-plane traffic segregation is correct on the DSLAM.

What Can Be Monitored

L2CP alarm severity profile configuration
local L2CP host interface VLAN settings
L2CP interface operational/fault status

Imported Objects

From AN-SHE-MIB

she	OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From SHE-ALARMING-MIB

SheAlarmSevProfileIndex
sheAlarmReportingSource	OBJECT-TYPE
sheAlarmReportingSourceType	OBJECT-TYPE
sheAlarmSeverity	OBJECT-TYPE
sheAlarmTimeAndDate	OBJECT-TYPE

From SHE-TC-MIB

SheControlStatusType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

OIDs

OID symbolic	OID numeric	Type	Access	Description
sheL2cpMib	1.3.6.1.4.1.231.7.1.2.2.1.16			She L2CP interface description.
sheL2cpObjects	1.3.6.1.4.1.231.7.1.2.2.1.16.1
sheL2cpIfTable	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2		not-accessible	The L2CP interface table.
sheL2cpIfEntry	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1		not-accessible	An entry of the L2CP interface table (sheL2cpIfTable)
INT sheL2cpIfIndex	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.1	INTEGER	read-only	The index of an L2CP protocol instance in the sheL2cpIfTable.
SHE sheL2cpOperState	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.2	SheL2cpOperStateType	read-only	The operational state of the L2CP interface.
SHE sheL2cpAdjacencyState	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.3	SheL2cpAdjacencyStateType	read-only	The state of the adjacency protocol.
INT sheL2cpTimer1	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.4	INTEGER	read-only	This timer defines the TIMER field is used to inform the receiver of the timer value used in the adjacency protocol of the sender. The timer specifies the nominal time between periodic adjacency protocol messages. It is a constant for the duration of a session.
INT sheL2cpTimer2	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.5	INTEGER	read-only	This value defines the minimum time between two port state messages of the same port. It is used to limit the port messages in case of toggeling ports. The timer base is 1s. 0 means: all port state changes are reported.
INT sheL2cpTimer3	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.6	INTEGER	read-only	This timeout is used to handle L2CP message flooding after Controller recovery. The timer is started when the link to the controller was established, The first port state message is sent when this timer expires.
OCT sheL2cpControllerIpAddress	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.7	OCTET STRING	read-only	The IP address of the remote L2cp controller which should be contacted by this interface.
OCT sheL2cpAccessNodeIdentifier	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.8	OCTET STRING	read-only	The name of the access node. The DSLAM identifies itself with the controller by means of this name.
SHE sheL2cpPartitionId	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.10	SheL2cpPartitionIdType	read-only	The ID of the partition managed via this L2CP protocol instance. (see RFC 3292). The value 257 is not used here.
SHE sheL2cpAlarmSeverityIndex	1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.11	SheAlarmSevProfileIndex	read-only	The currently used alarm severity profile index for this l2cp interface.
sheL2cpPortPartitionTable	1.3.6.1.4.1.231.7.1.2.2.1.16.1.3		not-accessible	The L2CP port table. The index in this table is the ifIndex. But only such interfaces are listed in this table which are of type xDSL.
sheL2cpPortPartitionEntry	1.3.6.1.4.1.231.7.1.2.2.1.16.1.3.1		not-accessible	An entry in the L2CP port partition table (sheL2cpPortPartitionTable).
SHE sheL2cpPortPartitionId	1.3.6.1.4.1.231.7.1.2.2.1.16.1.3.1.2	SheL2cpPartitionIdType	read-only	The ID of the partition managed the port is assigned to. 0...255: These are really partition IDs. The port is managed by such L2CP interface instances which have the same partition ID. 256: no partition. The port belongs to no partition. It is managed by such L2CP interface instances wich are assigned to 'no partition'. 257: invalid partition The port is not managed by any L2CP instance.
sheL2cpControl	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4
SHE sheL2cpControlRequest	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.1	SheL2cpControlRequestType	read-write	The L2CP commands: createL2cpIf: Create a new L2CP interface instance: Parameter: sheL2cpControlTimer1, sheL2cpControlTimer2, sheL2cpControlTimer3, sheL2cpControlControllerIpAddress, sheL2cpControlPartitionId, sheL2cpControlAccessNodeIdentifier sheL2cpControlAlarmSeverityIndex deleteL2cpIf: Delete a L2CP interface instance. Parameter: sheL2cpControlIndex modifyL2cpIf: Change the parameter of an L2CP interface instance. Parameter: sheL2cpControlL2cpIndex, sheL2cpControlTimer1, sheL2cpControlTimer2, sheL2cpControlTimer3, sheL2cpControlControllerIpAddress, sheL2cpControlPartitionId, sheL2cpControlAccessNodeIdentifier sheL2cpControlAlarmSeverityIndex assignPortToPartition: A port is assigned to a partition. Parameter: sheL2cpControlIndex, sheL2cpControlPartitionId
U32 sheL2cpControlIndex	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.2	Unsigned32	read-write	The index of a port in the port partition table (vshL2cpPortPartitionTable) if the PartionId should be set or the index of a valid L2cpIf in the sheL2cpIfTable for modify or delete of these interface.
SHE sheL2cpControlStatus	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.3	SheControlStatusType	read-only	The status of a user command.
SHE sheL2cpControlReqResult	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.4	SheL2cpControlRequestResultType	read-only	The result of the last ControlRequest
I32 sheL2cpControlTimer	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.5	Integer32	read-only	The maximum wait time for the manager for a long running user command.
I32 sheL2cpControlTimeStamp	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.6	Integer32	read-only	The time stamp of the last command (end of command).
INT sheL2cpControlTimer1	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.7	INTEGER	read-write	This timer defines the timer value used by the adjacency protocol. It defines the time between perdiodic adjacency protocol messages. The time base are 100ms. (see RFC 3292)
INT sheL2cpControlTimer2	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.8	INTEGER	read-write	This value defines the minimum time between two port state messages of the same port. It is used to limit the port messages in case of toggeling ports. The timer base is 1s. 0 means: all port state changes are reported.
INT sheL2cpControlTimer3	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.9	INTEGER	read-write	This value defines the time before all port states are reported to controller after an L2CP connection was established. This timer can be used to avoid a message flooding of the controller. The timer base is 1s.
OCT sheL2cpControlControllerIpAddress	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.10	OCTET STRING	read-write	The IP address of the controller.
OCT sheL2cpControlAccessNodeIdentifier	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.11	OCTET STRING	read-write	The name of the access node. The DSLAM identifies itself with the controller by means of this name.
SHE sheL2cpControlPartitionId	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.12	SheL2cpPartitionIdType	read-write	The ID of the partition managed by an L2CP protocol instance (see RFC 3292). The partition to which a port is assigned.
SHE sheL2cpControlAlarmSeverityIndex	1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.13	SheAlarmSevProfileIndex	read-write	look at table.
sheL2cpNotification	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5
sheL2cpAlarmEvents	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.1
NTF sheL2cpLinkDown	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.1.1			Description.
sheL2cpConfigEvents	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2
NTF sheL2cpIfCreated	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.1			Configuration trap.
NTF sheL2cpIfDeleted	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.2			Configuration trap.
NTF sheL2cpIfModified	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.3			Configuration trap.
NTF sheL2cpPartitionPortDataChanged	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.4			Configuration trap.
NTF sheL2cpHostIfCreated	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.5			Note: This parameter is not longer valid starting with release SHE R2.6 The IP interface configuration was moved to sheSystemIpHostTable.
NTF sheL2cpHostIfModified	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.6			Note: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable.
NTF sheL2cpHostIfDeleted	1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.7			Note: This parameter is not longer valid starting with release SHE R2.6 The IP interface configuration was moved to sheSystemIpHostTable.
sheL2cpHostIfTable	1.3.6.1.4.1.231.7.1.2.2.1.16.1.6		not-accessible	Note: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable.
sheL2cpHostIfEntry	1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1		not-accessible	The index of an L2CP host interface instance in this table. Note: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable.
INT sheL2cpHostIfIndex	1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.1	INTEGER	read-only	Unique key for that table.
U32 sheL2cpHostIfVlanId	1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.2	Unsigned32	read-only	The host vlan for the local L2cp interface which should be used as tag to contact the remote L2cp controller.
OCT sheL2cpHostIfIpAddress	1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.3	OCTET STRING	read-only	The IP address of the local L2cp interface which should be used by the NE.
OCT sheL2cpHostIfNetmask	1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.5	OCTET STRING	read-only	The l2cp host interface Netmask.
sheL2cpHostIfControl	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7
SHE sheL2cpHostIfControlRequest	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.1	SheL2cpControlRequestType	read-write	The L2CP commands: Note: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable. createL2cpHostIf: Create a new L2CP host interface instance: Parameter: sheL2cpHostIfControlVlanId sheL2cpHostIfControlIpAddress sheL2cpHostIfControlNetmask deleteL2cpHostIf: Delete a L2CP host interface instance. Parameter: sheL2cpHostIfControlIndex modifyL2cpHostIf: Change the parameter of an L2CP host interface instance. Parameter: sheL2cpHostIfControlIndex sheL2cpHostIfControlIpAddress sheL2cpHostIfControlNetmask
U32 sheL2cpHostIfControlIndex	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.2	Unsigned32	read-write	The index of a valid L2cpHostIf from sheL2cpHostIfTable for modifies or delete.
SHE sheL2cpHostIfControlStatus	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.3	SheControlStatusType	read-only	The status of a user command.
SHE sheL2cpHostIfControlReqResult	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.4	SheL2cpControlRequestResultType	read-only	The result of the last ControlRequest
I32 sheL2cpHostIfControlTimer	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.5	Integer32	read-only	The maximum wait time for the manager for a long running user command.
I32 sheL2cpHostIfControlTimeStamp	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.6	Integer32	read-only	The time stamp of the last command (end of command).
U32 sheL2cpHostIfControlVlanId	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.7	Unsigned32	read-write	The host vlan for the local L2cp interface which should be used as tag to contact the remote L2cp controller. This value could only be used for create command. A modification is not allowed!
OCT sheL2cpHostIfControlIpAddress	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.8	OCTET STRING	read-write	The IP address of the local L2cp host interface.
OCT sheL2cpHostIfControlNetmask	1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.10	OCTET STRING	read-write	The l2cp host interface Netmask.
sheL2cpConformance	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8
sheL2cpGroups	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1
sheL2cpGroup	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.1			A collection of objects providing information about a VDSL Line.
sheL2cpControlGroup	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.2			Description.
sheL2cpNotificationGroup	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.3			This group supports notifications of significant conditions associated with VDSL Lines.
sheL2cpObsoleteGroup	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.4			Description.
sheL2cpObsoleteNotificationGroup	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.5			Description.
sheL2cpCompliances	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.2
sheL2cpMibCompliance	1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.2.1			The compliance statement for SNMP entities which manage VDSL interfaces in SHE.

RFC description

Layer 2 Control Protocol interface management for Nokia Siemens Networks DSLAMs with alarm severity and control status.

Start monitoring Nokia Siemens Networks hiX5622/5625/5630/5635 DSLAM (L2CP interface VLAN/alarm-severity configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SHE-L2CP-MIB

What Is SHE-L2CP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description