SHE-MELT-MIB

All MIBs › SHE-MELT-MIB

Organization: Nokia Siemens Networks

Last Updated: 2009-07-16

Description: Nokia Siemens Networks SHE DSLAM Metallic Line Testing (MELT) control commands and measurement results for copper loop diagnostics per ITU-T G.996.2

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SHE-MELT-MIB?

SHE-MELT-MIB is a Nokia Siemens Networks proprietary module for the SHE DSLAM (Digital Subscriber Line Access Multiplexer) platform, targeting copper-access broadband infrastructure. It exposes control commands and result objects for Metallic Line Testing (MELT), the copper-loop diagnostic scheme defined in ITU-T G.996.2, so it is squarely a fault/diagnostics-oriented MIB rather than a general interface or performance module. In monitoring terms it is used to trigger and read back per-line electrical tests (loop resistance, capacitance, insulation, and foreign-voltage checks) that reveal degraded or faulty copper pairs before they cause a full subscriber outage, effectively serving as a hardware/wiring health check for DSL lines. It builds on ITU-T G.996.2 test definitions and is meant to be used alongside the vendor's broader SHE DSLAM MIB set rather than standalone. It is deployed by telecom operators running SHE DSLAM chassis in the access network, typically invoked on demand from an NMS or CLI when a subscriber reports line trouble, with technicians occasionally opening a SHE-MELT-MIB MIB Browser session to confirm the test control and result objects available.

IPNetwork Monitor allows you to monitor SNMP objects defined in SHE-MELT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nokia Siemens Networks SHE DSLAM

Monitoring Examples

An operator troubleshooting a customer complaint would set a MELT control object to initiate a metallic line test against a specific DSLAM port and then poll the corresponding result object for measured loop resistance or capacitance values. Because sample object names were not available in the source, a realistic naming pattern would follow sheMeltTestTable/sheMeltTestEntry with per-port index and result fields (e.g. resistance, capacitance, fault type). An abnormal reading (e.g. very low insulation resistance) would indicate water ingress or a damaged copper pair long before DSL sync loss becomes visible. This lets field technicians be dispatched with a specific fault type already diagnosed remotely.

What Can Be Monitored

metallic line test status
loop resistance/capacitance readings
insulation fault detection
test trigger/result per DSLAM port
copper pair diagnostic history

Imported Objects

From AN-SHE-MIB

she	OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From SHE-TC-MIB

SheControlStatusType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
sheMelt	1.3.6.1.4.1.231.7.1.2.2.1.24			Definition of MELT (metallic line testing) feature control commands and results. New supported with R3.7M.
sheMeltTestRequestObjects	1.3.6.1.4.1.231.7.1.2.2.1.24.1
sheMeltTestParameter	1.3.6.1.4.1.231.7.1.2.2.1.24.1.1
SHE sheMeltTestParameterFreq1	1.3.6.1.4.1.231.7.1.2.2.1.24.1.1.1	SheMeltTestFrequencyType	read-only	This parameter contains the used frequency 1 for MELT impedance/admittance test.
sheMeltTestRequestStateTable	1.3.6.1.4.1.231.7.1.2.2.1.24.1.2		not-accessible	Each entry in this table contains the testing status of each IfIndex. Only indeces of MELT feature supporting interfaces are listed in this table!
sheMeltTestRequestStateEntry	1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1		not-accessible	An entry in sheMeltTestRequestIfTable.
SHE sheMeltTestRequestIfState	1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1.1	SheMeltTestRequestIfStateType	read-only	The MELT status of this interface. Only one port of one IU could be under test at time. Ports on different IU's could be under test at the same time. Check the corresponding sheMeltTestRequestIuState for this precondition. NOTE: Wetting current injection will be autonomously interrupted, if MELT or testTone insertion is started (WC configuration himself via sheXdslMib or sheShdslMib) for this interface as long as the test is running. Forgetting to stop test tone insertion will inhibit wetting current!
SHE sheMeltTestRequestIuState	1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1.2	SheMeltTestRequestIuStateType	read-only	The MELT status of IU where this interface is located on. Every port must know whether this IU is under melt test already or not, in order to decide if the melt test request on this port can be accepted. Only one port of one IU could be under test at time. Ports on different IU's could be under test at the same time.
SHE sheMeltTestRequestTestToneIndex	1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1.3	SheMeltTestToneIndexType	read-only	This parameter points on a valid entry of sheMeltTestToneTable. These configuration is needed for test tone insertion on this line. One default profile with index 1 will always exist and is assigned per default to each line!
sheMeltTestRequestStateControl	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3
SHE sheMeltTestRequestControlReq	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.1	SheMeltControlReqType	read-write	setMeltTestParameters (1): sheMeltTestRequestControlParameterFreq1 startMeltTest (2): sheMeltTestRequestControlIndex stopMeltTest (3): sheMeltTestRequestControlIndex activateTestTone (4): sheMeltTestRequestControlIndex deactivateTestTone (5): sheMeltTestRequestControlIndex setMeltTestRequestTestToneIndex (8): sheMeltTestRequestControlIndex sheMeltTestRequestControlTestToneIndex
NUM sheMeltTestRequestControlIndex	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.2	InterfaceIndex	read-write	The interface index of the DSL central PPTP which should be configured.
SHE sheMeltTestRequestControlStatus	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.3	SheControlStatusType	read-only	The status of a control request.
U32 sheMeltTestRequestControlTimer	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.4	Unsigned32	read-only	The maximum wait time for the manager for a long running user command.
SHE sheMeltTestRequestControlReqResult	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.5	SheMeltControlReqResultType	read-only	The result of the last user command.
U32 sheMeltTestRequestControlReqTimeStamp	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.6	Unsigned32	read-only	The time stamp of the last command (end of command).
SHE sheMeltTestRequestControlTestToneIndex	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.7	SheMeltTestToneIndexType	read-write	look at table
SHE sheMeltTestRequestControlParameterFreq1	1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.8	SheMeltTestFrequencyType	read-write	Look at basic parameter group.
sheMeltTestToneObjects	1.3.6.1.4.1.231.7.1.2.2.1.24.2
sheMeltTestToneTable	1.3.6.1.4.1.231.7.1.2.2.1.24.2.1		not-accessible	Each entry in this table contains a set of parameters for test tone generation. These entries could be assigned to each interface. One default entry exist which could NOT be modified or deleted!
sheMeltTestToneEntry	1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1		not-accessible	An entry in sheMeltTestToneTable.
SHE sheMeltTestToneIndex	1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.1	SheMeltTestToneIndexType	read-only	This parameter is index of sheMeltTestToneTable. This configuration is needed for test tone insertion on the line. One default profile with index 1 will always exist and is assigned per default to each line!
SHE sheMeltTestToneFreq1	1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.2	SheMeltTestToneFrequencyType	read-only	The test tone frequency 1 of test tone set.
SHE sheMeltTestToneFreq2	1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.3	SheMeltTestToneFrequencyType	read-only	The test tone frequency 2 of test tone set.
SHE sheMeltTestToneLevel	1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.4	SheMeltTestSignalLevelType	read-only	The test tone level of test tone set.
sheMeltTestToneControl	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2
SHE sheMeltTestToneControlReq	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.1	SheMeltControlReqType	read-write	createMeltTestToneEntry (10): (index will autonomously generated by NE) sheMeltTestToneControlFreq1 sheMeltTestToneControlFreq2 sheMeltTestToneControlLevel modifyMeltTestToneEntry (11): sheMeltTestToneControlIndex sheMeltTestToneControlFreq1 sheMeltTestToneControlFreq2 sheMeltTestToneControlLevel deleteMeltTestToneEntry (12): sheMeltTestToneControlIndex
SHE sheMeltTestToneControlIndex	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.2	SheMeltTestToneIndexType	read-write	The table index of the TestToneTable which should be configured. Default tone-set 1 could not be modified or deleted!
SHE sheMeltTestToneControlStatus	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.3	SheControlStatusType	read-only	The status of a control request.
U32 sheMeltTestToneControlTimer	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.4	Unsigned32	read-only	The maximum wait time for the manager for a long running user command.
SHE sheMeltTestToneControlReqResult	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.5	SheMeltControlReqResultType	read-only	The result of the last user command.
U32 sheMeltTestToneControlReqTimeStamp	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.6	Unsigned32	read-only	The time stamp of the last command (end of command).
SHE sheMeltTestToneControlFreq1	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.7	SheMeltTestToneFrequencyType	read-write	look at table
SHE sheMeltTestToneControlFreq2	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.8	SheMeltTestToneFrequencyType	read-write	look at table
SHE sheMeltTestToneControlLevel	1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.9	SheMeltTestSignalLevelType	read-write	look at table
sheMeltTestResultObjects	1.3.6.1.4.1.231.7.1.2.2.1.24.3
sheMeltTestResultTable	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1		not-accessible	Each entry in this table contains the testing results of each IfIndex. Only indeces of MELT feature supporting interfaces are listed in this table!
sheMeltTestResultEntry	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1		not-accessible	An entry in sheMeltTestResultTable.
SHE sheMeltTestResultState	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.1	SheMeltTestResultStateType	read-only	The MELT result status of this interface.
U32 sheMeltTestResultTimeStamp	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.2	Unsigned32	read-only	Timestamp of last executed MELT.
SHE sheMeltTestResultCapacityAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.3	SheMeltTestResultCapacityType	read-only	The MELT result for capacity a-wire - b-wire (ring - tip).
SHE sheMeltTestResultCapacityABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.4	SheMeltTestResultValidType	read-only	The valid information for capacitytest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultCapacityAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.5	SheMeltTestResultCapacityType	read-only	The MELT result for capacity a-wire - E (ring - earth).
SHE sheMeltTestResultCapacityAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.6	SheMeltTestResultValidType	read-only	The valid information for capacitytest a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultCapacityBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.7	SheMeltTestResultCapacityType	read-only	The MELT result for capacity b-wire - E (tip - earth).
SHE sheMeltTestResultCapacityBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.8	SheMeltTestResultValidType	read-only	The valid information for capacitytest b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultResistanceAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.9	SheMeltTestResultResistanceType	read-only	The MELT result for resistance a-wire - b-wire (ring - tip). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.
SHE sheMeltTestResultResistanceABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.10	SheMeltTestResultValidType	read-only	The valid information for resistancetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultResistanceBA	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.11	SheMeltTestResultResistanceType	read-only	The MELT result for resistance b-wire - a-wire (tip - ring). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.
SHE sheMeltTestResultResistanceBAValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.12	SheMeltTestResultValidType	read-only	The valid information for resistancetest b-wire - a-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultResistanceAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.13	SheMeltTestResultResistanceType	read-only	The MELT result for resistance a-wire - E (ring - earth). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.
SHE sheMeltTestResultResistanceAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.14	SheMeltTestResultValidType	read-only	The valid information for resistancetest a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultResistanceBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.15	SheMeltTestResultResistanceType	read-only	The MELT result for resistance b-wire - E (tip - earth). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.
SHE sheMeltTestResultResistanceBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.16	SheMeltTestResultValidType	read-only	The valid information for resistancetest b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageDcAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.17	SheMeltTestResultDCVoltageType	read-only	The MELT result for foreign voltage DC a-wire - b-wire (ring - tip).
SHE sheMeltTestResultForeignVoltageDcABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.18	SheMeltTestResultValidType	read-only	The valid information for foreignDcVoltagetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageDcAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.19	SheMeltTestResultDCVoltageType	read-only	The MELT result for foreign voltage DC a-wire - E (ring - earth).
SHE sheMeltTestResultForeignVoltageDcAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.20	SheMeltTestResultValidType	read-only	The valid information for foreignDcVoltagetest a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageDcBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.21	SheMeltTestResultDCVoltageType	read-only	The MELT result for foreign voltage DC b-wire - E (tip - earth).
SHE sheMeltTestResultForeignVoltageDcBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.22	SheMeltTestResultValidType	read-only	The valid information for foreignDcVoltagetest b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageAcAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.23	SheMeltTestResultACVoltageType	read-only	The MELT result for foreign voltage AC a-wire - b-wire (ring - tip).
SHE sheMeltTestResultForeignVoltageAcABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.24	SheMeltTestResultValidType	read-only	The valid information for foreignAcVoltage test a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageAcAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.25	SheMeltTestResultACVoltageType	read-only	The MELT result for foreign voltage AC a-wire - E (ring - earth).
SHE sheMeltTestResultForeignVoltageAcAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.26	SheMeltTestResultValidType	read-only	The valid information for foreignAcVoltagetest a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageAcBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.27	SheMeltTestResultACVoltageType	read-only	The MELT result for foreign voltage AC b-wire - E (tip - earth).
SHE sheMeltTestResultForeignVoltageAcBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.28	SheMeltTestResultValidType	read-only	The valid information for foreignAcVoltagetest b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageAcFrequencyAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.29	SheMeltTestResultACVoltageFrequencyType	read-only	The MELT result for foreign voltage AC frequency a-wire - b-wire (ring - tip).
SHE sheMeltTestResultForeignVoltageAcFrequencyABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.30	SheMeltTestResultValidType	read-only	The valid information for foreignAcVoltageFrequency test a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageAcFrequencyAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.31	SheMeltTestResultACVoltageFrequencyType	read-only	The MELT result for foreign voltage AC frequency a-wire - earth (ring - earth).
SHE sheMeltTestResultForeignVoltageAcFrequencyAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.32	SheMeltTestResultValidType	read-only	The valid information for foreignAcVoltageFrequency test a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignVoltageAcFrequencyBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.33	SheMeltTestResultACVoltageFrequencyType	read-only	The MELT result for foreign voltage AC frequency b-wire - earth (tip - earth).
SHE sheMeltTestResultForeignVoltageAcFrequencyBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.34	SheMeltTestResultValidType	read-only	The valid information for foreignAcVoltageFrequency test b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignCurrentAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.35	SheMeltTestResultForeignCurrentType	read-only	The MELT result for foreign current test a-wire - b-wire (ring - tip).
SHE sheMeltTestResultForeignCurrentABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.36	SheMeltTestResultValidType	read-only	The valid information for foreignCurrenttest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignCurrentAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.37	SheMeltTestResultForeignCurrentType	read-only	The MELT result for foreign current test a-wire - E (ring - earth).
SHE sheMeltTestResultForeignCurrentAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.38	SheMeltTestResultValidType	read-only	The valid information for foreignCurrenttest a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultForeignCurrentBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.39	SheMeltTestResultForeignCurrentType	read-only	The MELT result for foreign current test b-wire - E (tip - earth).
SHE sheMeltTestResultForeignCurrentBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.40	SheMeltTestResultValidType	read-only	The valid information for foreignCurrenttest b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultConductanceAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.41	SheMeltTestResultConductanceType	read-only	The MELT result for conductance test a-wire - b-wire (ring - tip).
SHE sheMeltTestResultConductanceABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.42	SheMeltTestResultValidType	read-only	The valid information for conductancetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultConductanceAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.43	SheMeltTestResultConductanceType	read-only	The MELT result for conductance test a-wire - earth (ring - earth).
SHE sheMeltTestResultConductanceAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.44	SheMeltTestResultValidType	read-only	The valid information for conductancetest a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultConductanceBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.45	SheMeltTestResultConductanceType	read-only	The MELT result for conductance test b-wire - earth (tip - earth).
SHE sheMeltTestResultConductanceBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.46	SheMeltTestResultValidType	read-only	The valid information for conductancetest b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultSusceptanceAB	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.47	SheMeltTestResultConductanceType	read-only	The MELT result for susceptance test a-wire - b-wire (ring - tip).
SHE sheMeltTestResultSusceptanceABValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.48	SheMeltTestResultValidType	read-only	The valid information for susceptancetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultSusceptanceAE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.49	SheMeltTestResultConductanceType	read-only	The MELT result for susceptance test a-wire - earth (ring - earth).
SHE sheMeltTestResultSusceptanceAEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.50	SheMeltTestResultValidType	read-only	The valid information for susceptancetest a-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultSusceptanceBE	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.51	SheMeltTestResultConductanceType	read-only	The MELT result for susceptance test b-wire - earth (tip - earth).
SHE sheMeltTestResultSusceptanceBEValid	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.52	SheMeltTestResultValidType	read-only	The valid information for susceptancetest b-wire - earth, if sheMeltTestResultState = testSucceeded.
SHE sheMeltTestResultCheckPPA	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.53	SheMeltTestResultCheckPpaType	read-only	The MELT result for PPA test.
SHE sheMeltTestResultCheckSplitter	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.54	SheMeltTestResultCheckType	read-only	The MELT result for Splitter test.
SHE sheMeltTestResultCheckIAD	1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.55	SheMeltTestResultCheckType	read-only	The MELT result for IAD test.
sheMeltNotifications	1.3.6.1.4.1.231.7.1.2.2.1.24.10
NTF sheMeltTestRequestParametersModified	1.3.6.1.4.1.231.7.1.2.2.1.24.10.1			The MELT testparameters are modified.
NTF sheMeltTestRequestStateModified	1.3.6.1.4.1.231.7.1.2.2.1.24.10.2			The MELT state of an interface was modified by command or by NE.
NTF sheMeltTestRequestIfTestToneIndexModified	1.3.6.1.4.1.231.7.1.2.2.1.24.10.3			The used test tone set of an interface (assignment interface - test tone index) was modified.
NTF sheMeltTestToneEntryCreated	1.3.6.1.4.1.231.7.1.2.2.1.24.10.4			Configuration trap for new created MELT testTone set.
NTF sheMeltTestToneEntryModified	1.3.6.1.4.1.231.7.1.2.2.1.24.10.5			Configuration trap for modified MELT testTone set.
NTF sheMeltTestToneEntryDeleted	1.3.6.1.4.1.231.7.1.2.2.1.24.10.6			Configuration trap for delete a MELT testTone set.
sheMeltConformance	1.3.6.1.4.1.231.7.1.2.2.1.24.100
sheMeltCompliances	1.3.6.1.4.1.231.7.1.2.2.1.24.100.1
sheMeltMibCompliance	1.3.6.1.4.1.231.7.1.2.2.1.24.100.1.1			Description.
sheMeltGroups	1.3.6.1.4.1.231.7.1.2.2.1.24.100.2
sheMeltGroup	1.3.6.1.4.1.231.7.1.2.2.1.24.100.2.1
sheMeltControlGroup	1.3.6.1.4.1.231.7.1.2.2.1.24.100.2.2			Description.
sheMeltNotificationGroup	1.3.6.1.4.1.231.7.1.2.2.1.24.100.2.3

RFC description

Nokia Siemens Networks private MIB for managing MELT (Metallic Line Testing) feature on DSLAM equipment.

Start monitoring Nokia Siemens Networks DSLAMs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SHE-MELT-MIB

What Is SHE-MELT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description