SCHLEIFENBAUER-DATABUS-MIB

All MIBs › SCHLEIFENBAUER-DATABUS-MIB

Organization: Schleifenbauer Engineering

Last Updated: 2016-10-21

Category: Environmental and Power Monitoring, Intelligent PDU Management

Description: Manages Schleifenbauer Engineering intelligent PDU databus protocol communication and device discovery.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SCHLEIFENBAUER-DATABUS-MIB?

SCHLEIFENBAUER-DATABUS-MIB is a vendor MIB from Schleifenbauer Engineering (Schleifenbauer Holding BV), a manufacturer of intelligent power distribution units (PDUs) for data center racks, covering the proprietary databus protocol that links chained PDU devices together in a ring topology. It exposes device-discovery data (total, addressable, new, and duplicate devices on the bus) and ring-topology health (ring state and ring breach location), plus control actions for scanning and renumbering devices. This is fundamentally hardware-status monitoring: a ring breach or duplicate-device condition signals a physical wiring fault or address conflict among daisy-chained PDU units, letting an operator pinpoint a failed link before it causes a cascading loss of power monitoring across the rack row. The module is typically used alongside Schleifenbauer's own outlet/power-metering MIB rather than any IETF standard, since the databus is a proprietary discovery layer underneath the metered PDU objects. It is deployed in data center and colocation environments where multiple intelligent PDUs are daisy-chained on a shared communication ring and centrally polled by a DCIM or power-monitoring system. Engineers can download the SCHLEIFENBAUER-DATABUS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SCHLEIFENBAUER-DATABUS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Schleifenbauer intelligent PDU
data center rack power distribution unit

Monitoring Examples

An administrator would poll sdbMgmtStsRingState and sdbMgmtStsRingBreachIndex to detect and localize a break in the PDU ring bus, and check sdbMgmtStsDuplicateDevices and sdbMgmtStsNewDevices after adding or replacing a unit to confirm it was assigned a unique address. The sdbMgmtCtrlDevicesTable / sdbMgmtCtrlDevicesEntry, indexed by sdbMgmtCtrlDevIndex, enumerates each device discovered on the bus for inventory and troubleshooting. Control objects like sdbMgmtCtrlScan and sdbMgmtCtrlRenumberAllFromN let the admin trigger a rescan or renumber devices after physical changes to the chain.

What Can Be Monitored

number of devices on the databus
number of addressable devices
newly discovered devices
duplicate device addresses
ring topology state
ring breach location

Imported Objects

From SCHLEIFENBAUER-SMI

schleifenbauerMgmt

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using sdbMgmtStsDevices OID:

Select a Schleifenbauer intelligent PDU, data center rack power distribution unit (databus ring topology health) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type sdbMgmtStsDevices into the Find box to locate it in the OID tree, then select it and click OK. The number of devices on the databus. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the count changes from its expected baseline, since that would indicate the underlying set of items changed unexpectedly. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
schleifenbauerDatabusMIB	1.3.6.1.4.1.31034.12.1			This MIB describes the SNMP functions of network enabled databus devices. Copyright (c) 2016 by Schleifenbauer Holding BV
sdbMIBNotifications	1.3.6.1.4.1.31034.12.1.0
NTF sdbDevSsDeviceStatusCodeChanged	1.3.6.1.4.1.31034.12.1.0.1			Device status code changed. OBJECTS { sdbDevSsDeviceStatusCode }
NTF sdbDevSsTemperatureAlertDetected	1.3.6.1.4.1.31034.12.1.0.2			Temperature alert detected. Internal temperature alert: OBJECTS { sdbDevSsTemperatureAlert, sdbDevMsIntTemperature, sdbDevMsIntTemperaturePeak } External analog temperature alert: OBJECTS { sdbDevSsTemperatureAlert, sdbDevMsExtTemperature, sdbDevMsExtTemperaturePeak } External digital temperature alert: OBJECTS { sdbDevSsTemperatureAlert, sdbDevSnsValue }
NTF sdbDevSsInputCurrentAlertDetected	1.3.6.1.4.1.31034.12.1.0.3			Input current alert detected. OBJECTS { sdbDevSsInputCurrentAlert, sdbDevInActualCurrent }
NTF sdbDevSsOutletCurrentAlertDetected	1.3.6.1.4.1.31034.12.1.0.4			Outlet current alert detected. OBJECTS { sdbDevSsOutletCurrentAlert, sdbDevOutMtActualCurrent }
NTF sdbDevSsInputVoltageAlertDetected	1.3.6.1.4.1.31034.12.1.0.5			Input voltage alert detected. OBJECTS { sdbDevSsInputVoltageAlert, sdbDevInActualVoltage }
NTF sdbDevSsOutletCurrentDropAlertDetected	1.3.6.1.4.1.31034.12.1.0.6			Outlet current drop alert detected. OBJECTS { sdbDevSsOutletCurrentDropAlert, sdbDevOutMtActualCurrent }
NTF sdbDevSsInputCurrentDropAlertDetected	1.3.6.1.4.1.31034.12.1.0.7			Input current drop alert detected. OBJECTS { sdbDevSsInputCurrentDropAlert, sdbDevInActualCurrent }
NTF sdbDevSsSensorChangeAlertDetected	1.3.6.1.4.1.31034.12.1.0.8			Sensor channel change alert detected. OBJECTS { sdbDevSsSensorChangeAlert }
NTF sdbMgmtStsRingStateChanged	1.3.6.1.4.1.31034.12.1.0.9			Ring state changed. Ring state changded to open: OBJECTS { sdbMgmtStsRingState, sdbMgmtStsRingBreachIndex } Ring state changded to closed: OBJECTS { sdbMgmtStsRingState }
NTF sdbDevSsOutletVoltageDropAlertDetected	1.3.6.1.4.1.31034.12.1.0.10			Outlet voltage drop alert detected. OBJECTS { sdbDevSsOutletVoltageDropAlert, sdbDevOutMtActualVoltage }
sdbMIBObjects	1.3.6.1.4.1.31034.12.1.1
sdbMgmt	1.3.6.1.4.1.31034.12.1.1.1
sdbMgmtStatus	1.3.6.1.4.1.31034.12.1.1.1.1
I32 sdbMgmtStsDevicesEx	1.3.6.1.4.1.31034.12.1.1.1.1.1	Integer32	read-only	The number of devices on the databus.
I32 sdbMgmtStsAddressableDevices	1.3.6.1.4.1.31034.12.1.1.1.1.2	Integer32	read-only	The number of devices on the databus addressable by snmp.
I32 sdbMgmtStsNewDevices	1.3.6.1.4.1.31034.12.1.1.1.1.3	Integer32	read-only	The number of new devices on the databus.
I32 sdbMgmtStsDuplicateDevices	1.3.6.1.4.1.31034.12.1.1.1.1.4	Integer32	read-only	The number of duplicate devices on the databus.
INT sdbMgmtStsRingState	1.3.6.1.4.1.31034.12.1.1.1.1.5	INTEGER	read-only	If the device is in a bridge-like mode, this will indicate the actual state of the databus.
I32 sdbMgmtStsRingBreachIndex	1.3.6.1.4.1.31034.12.1.1.1.1.6	Integer32	read-only	Indicates the breach index if the current state of the data bus is open. If the data bus is closed this has no meaning.
sdbMgmtControl	1.3.6.1.4.1.31034.12.1.1.1.2
INT sdbMgmtCtrlScan	1.3.6.1.4.1.31034.12.1.1.1.2.1	INTEGER	read-write	Perform a bus scan. To verify if scanning is completed the value of this object can be read. During the bus scan the value remains 1. When the bus scan completed the value will be 0.
I32 sdbMgmtCtrlRenumberAllFromN	1.3.6.1.4.1.31034.12.1.1.1.2.2	Integer32	read-write	Renumber all devices on the databus. If set to 0 all units will be set to 0. If set to another value, all units will be numbered in sequence starting from the value set.
INT sdbMgmtCtrlRenumberZeros	1.3.6.1.4.1.31034.12.1.1.1.2.3	INTEGER	read-write	Renumber all devices on the databus having address 0. Renumbering will be done in sequence. The sequence starts with the highest address found on the databus.
sdbMgmtCtrlDevicesTable	1.3.6.1.4.1.31034.12.1.1.1.2.4		not-accessible	A table containing information of devices connected to the databus. The number of entries is given by the value of sdbMgmtStsDevices.
sdbMgmtCtrlDevicesEntry	1.3.6.1.4.1.31034.12.1.1.1.2.4.1		not-accessible	Information entry containing objects of a particular databus device.
I32 sdbMgmtCtrlDevIndex	1.3.6.1.4.1.31034.12.1.1.1.2.4.1.1	Integer32	not-accessible	A unique value for each device. Its value ranges between 1 and the value of sdbMgmtStsDevices with a maximum of 255. The value for each device will remain constant until the next scan is performed.
I32 sdbMgmtCtrlDevUnitAddress	1.3.6.1.4.1.31034.12.1.1.1.2.4.1.2	Integer32	read-write	User defined address. This will be used for addressing the device on the databus.
STR sdbMgmtCtrlDevHardwareAddress	1.3.6.1.4.1.31034.12.1.1.1.2.4.1.3	DisplayString	read-only	Hardware serial number. This cannot be changed. It can be used as backup unit address. format as 3 unsigned ints separated by dashes: int - int - int
INT sdbMgmtCtrlDevIsNew	1.3.6.1.4.1.31034.12.1.1.1.2.4.1.4	INTEGER	read-only	Indication if the device is new on the databus.
INT sdbMgmtCtrlDevIsDuplicate	1.3.6.1.4.1.31034.12.1.1.1.2.4.1.5	INTEGER	read-only	Indication if the device is conflicting with another device on the databus.
sdbDevice	1.3.6.1.4.1.31034.12.1.1.2
sdbDevIdentification	1.3.6.1.4.1.31034.12.1.1.2.1
sdbDevIdTable	1.3.6.1.4.1.31034.12.1.1.2.1.1		not-accessible	A table containing identification information of devices connected to the databus. The number of entries is given by the value of sdbMgmtStsAddressableDevices.
sdbDevIdEntry	1.3.6.1.4.1.31034.12.1.1.2.1.1.1		not-accessible	Information entry containing information objects of a particular databus device.
I32 sdbDevIdSPDMVersion	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.1	Integer32	read-only	Data model version.
I32 sdbDevIdFirmwareVersion	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.2	Integer32	read-only	The firmware revision number.
STR sdbDevIdBuildNumber	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.3	DisplayString	read-only	Date and time the firmware was built.
STR sdbDevIdSalesOrderNumber	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.4	DisplayString	read-only	SP sales order number.
STR sdbDevIdProductId	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.5	DisplayString	read-only	SP product id.
STR sdbDevIdSerialNumber	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.6	DisplayString	read-only	SP serial number.
STR sdbDevIdHardwareAddress	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.7	DisplayString	read-only	Hardware serial number. This can not be changed. It can be used as backup unit address. Format as 3 unsigned ints separated by dashes (-) e.g. 12345-54321-00000
STR sdbDevIdMacAddress	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.8	DisplayString	read-only	The MAC address. This can not be changed. It represents an 802 MAC address as if it were transmitted least significant bit first. Format as six groups of 2 hexadecimal digits separated by colons (:) e.g. D0:22:12:B0:00:00
I32 sdbDevIdUnitAddress	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.9	Integer32	read-write	User defined address. This will be used for addressing the device on the databus.
STR sdbDevIdName	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.10	DisplayString	read-write	User configurable device name or identifier.
STR sdbDevIdLocation	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.11	DisplayString	read-write	User configurable device location identifier.
STR sdbDevIdVanityTag	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.12	DisplayString	read-write	Characters to be displayed as vanity text in display.
I32 sdbDevIdIndex	1.3.6.1.4.1.31034.12.1.1.2.1.1.1.13	Integer32	not-accessible	A unique value for each device. Its value represents the unit address of the device and is used to address individual devices in the tree. The value for each device will remain constant until the next scan is performed.
sdbDevConfiguration	1.3.6.1.4.1.31034.12.1.1.2.2
sdbDevCfTable	1.3.6.1.4.1.31034.12.1.1.2.2.1		not-accessible	A table containing configuration information of devices connected to the databus. The number of entries is given by the value of sdbMgmtStsAddressableDevices.
sdbDevCfEntry	1.3.6.1.4.1.31034.12.1.1.2.2.1.1		not-accessible	Configuration entry containing configuration objects of a particular databus device.
I32 sdbDevCfPhases	1.3.6.1.4.1.31034.12.1.1.2.2.1.1.1	Integer32	read-only	Number of phases for input metering.
I32 sdbDevCfOutletsTotal	1.3.6.1.4.1.31034.12.1.1.2.2.1.1.2	Integer32	read-only	Total number of outlets including hardwired without switch/metered modules.
I32 sdbDevCfOutletsSwitched	1.3.6.1.4.1.31034.12.1.1.2.2.1.1.3	Integer32	read-only	Number of switched outlets. If outlet numbering is non-contiguous its the highest outlet number.
I32 sdbDevCfOutletsMetered	1.3.6.1.4.1.31034.12.1.1.2.2.1.1.4	Integer32	read-only	Number of metered outlets. If outlet numbering is non-contiguous its the highest outlet number.
I32 sdbDevCfSensors	1.3.6.1.4.1.31034.12.1.1.2.2.1.1.5	Integer32	read-only	The number sensors.
I32 sdbDevCfMaximumLoad	1.3.6.1.4.1.31034.12.1.1.2.2.1.1.6	Integer32	read-only	Maximum rated load of device per phase
sdbDevSystemStatus	1.3.6.1.4.1.31034.12.1.1.2.3
sdbDevSsTable	1.3.6.1.4.1.31034.12.1.1.2.3.1		not-accessible	A table containing system status information of devices connected to the databus. The number of entries is given by the value of sdbMgmtStsAddressableDevices.
sdbDevSsEntry	1.3.6.1.4.1.31034.12.1.1.2.3.1.1		not-accessible	System status entry containing system status objects of a particular databus device.
I32 sdbDevSsDeviceStatusCode	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.1	Integer32	read-only	Returns an internal status or error code. A value of 0 means OK. If not 0 it can be any of the following codes. Multiple status codes can be active at the same time. The value will be the sum of the active status codes. 1 = alert flagged 2 = settings(s) initialized 4 = power-on reset 8 = external reset 16 = watchdog timer caused reset 32 = brownout detected 64 = controller error 128 = slave module was reset
I32 sdbDevSsTemperatureAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.2	Integer32	read-only	An alert has been raised due to temperature exceeding treshhold. 0 = no alert 1 = internal temperature sensor 2 = external temperature sensor
I32 sdbDevSsInputCurrentAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.3	Integer32	read-only	An alert has been raised due to current exceeding treshhold. The value indicates the exceeding phase. 0 = no alert.
I32 sdbDevSsOutletCurrentAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.4	Integer32	read-only	An alert has been raised due to current exceeding treshhold. The value indicates the exceeding outlet. 0 = no alert.
I32 sdbDevSsInputVoltageAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.5	Integer32	read-only	An alert has been raised due to a voltage dip. The value indicates the dipped phase. 0 = no alert.
I32 sdbDevSsOutletCurrentDropAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.6	Integer32	read-only	An alert has been raised due to the current of a metered outlet suddenly dropping to near zero, possibly indicating a blown fuse. The value indicates the dropped outlet. 0 = no alert.
I32 sdbDevSsInputCurrentDropAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.7	Integer32	read-only	An alert has been raised due to the current of a metered input suddenly dropping to near zero, possibly indicating a blown fuse. The value indicates the dropped phase. 0 = no alert.
I32 sdbDevSsSensorChangeAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.8	Integer32	read-only	An alert has been raised due to a change in the number of sensors. The value indicates the previous amount of sensors.
I32 sdbDevSsOutletVoltageDropAlert	1.3.6.1.4.1.31034.12.1.1.2.3.1.1.9	Integer32	read-only	An alert has been raised due to voltage drop on this outlet. The value indicates the first failed outlet.
sdbDevReset	1.3.6.1.4.1.31034.12.1.1.2.4
sdbDevRsTable	1.3.6.1.4.1.31034.12.1.1.2.4.1		not-accessible	A table providing reset capabilities to devices connected to the databus. The number of entries is given by the value of sdbMgmtStsAddressableDevices.
sdbDevRsEntry	1.3.6.1.4.1.31034.12.1.1.2.4.1.1		not-accessible	Reset entry providing reset objects of a particular databus device.
INT sdbDevRsReboot	1.3.6.1.4.1.31034.12.1.1.2.4.1.1.1	INTEGER	read-write	Warm reboot/reset of device controller. NOTE: this will have NO effect on outlet status!
INT sdbDevRsResetAlerts	1.3.6.1.4.1.31034.12.1.1.2.4.1.1.2	INTEGER	read-write	Reset all alert signals and device status code.
INT sdbDevRsZeroInputKWhSubtotal	1.3.6.1.4.1.31034.12.1.1.2.4.1.1.3	INTEGER	read-write	Reset of all input kWh subtotal counters to zero.
INT sdbDevRsZeroOutletKWhSubtotal	1.3.6.1.4.1.31034.12.1.1.2.4.1.1.4	INTEGER	read-write	Reset of all outlet kWh subtotal counter to zero.
INT sdbDevRsResetPeaksAndDips	1.3.6.1.4.1.31034.12.1.1.2.4.1.1.5	INTEGER	read-write	Reset all peak and dip values to zero.
sdbDevSettings	1.3.6.1.4.1.31034.12.1.1.2.5
sdbDevStTable	1.3.6.1.4.1.31034.12.1.1.2.5.1		not-accessible	A table containing setting information of devices connected to the databus. The number of entries is given by the value of sdbMgmtStsAddressableDevices.
sdbDevStEntry	1.3.6.1.4.1.31034.12.1.1.2.5.1.1		not-accessible	Setting entry containing settings objects of a particular databus device.
I32 sdbDevStAutoResetAlerts	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.2	Integer32	read-write	Auto reset alerts configuration. If set to 0 the auto reset alerts feature is disabled. If set to a value greater then 0, the auto reset alerts feature is enabled and alerts will get cleared after the configured amount of seconds since the last alert condition have passed.
INT sdbDevStExtendedNames	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.3	INTEGER	read-write	Use original or longer names for inputs, outlets and sensors.
MIL sdbDevStPeakDuration	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.4	MilliSecond	read-write	Amount of ms a current peak should last before an alert is raised.
MIL sdbDevStFixedOutletDelay	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.5	MilliSecond	read-write	Minimal delay between two successive relay switches in milliseconds. Minimal delay is 100 ms. Will always be respected!
SEC sdbDevStPowerSaverMode	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.6	Second	read-write	Set backlight on time in seconds. 0 keeps display always on. Note that keeping the backlight on may decrease luminosity over time.
INT sdbDevStOutletPowerUpMode	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.7	INTEGER	read-write	Behaviour of outlets on power-up.
I32 sdbDevStMaximumTemperature	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.8	Integer32	read-write	Maximum temperature threshold An alert will be generated whenever the temperature is above this value. Zero means disabled.
INT sdbDevStDisplayOrientation	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.9	INTEGER	read-write	Display orientation.
INT sdbDevStLocalAlertReset	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.10	INTEGER	read-write	Allow alerts to be reset locally on device by pushing one of the buttons.
INT sdbDevStCurrentDropDetection	1.3.6.1.4.1.31034.12.1.1.2.5.1.1.11	INTEGER	read-write	Enables the current drop detection function.
sdbDevInput	1.3.6.1.4.1.31034.12.1.1.2.6
sdbDevInTable	1.3.6.1.4.1.31034.12.1.1.2.6.1		not-accessible	A table containing information of inputs of devices connected to the databus.
sdbDevInEntry	1.3.6.1.4.1.31034.12.1.1.2.6.1.1		not-accessible	Inputs entry containing objects of an input of a particular databus device. Note that this table has two indexes. sdbDevIdIndex to identify a particular device and sdbDevInIndex to identify a particular input of the device identified by sdbDevIdIndex.
I32 sdbDevInIndex	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.1	Integer32	not-accessible	A unique value for each input. Its value ranges between 1 and the value of sdbDevCfPhases.
KIL sdbDevInKWhTotal	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.2	KiloWattHour	read-only	Total kWh value of an input. This value can not be reset.
KIL sdbDevInKWhSubtotal	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.3	KiloWattHour	read-only	Subtotal kWh value of an input. This value can be reset.
DEC sdbDevInPowerFactor	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.4	DeciPercent	read-only	Power factor of input. The power factor of an AC power system is defined as the ratio of the real or active power to the apparent power and is a number between 0 and 1. This value is expressed as a percentage between 0% and 100%.
DEC sdbDevInActualCurrent	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.5	DeciAmpere	read-only	Actual apparent, RMS current.
DEC sdbDevInPeakCurrent	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.6	DeciAmpere	read-only	Peak apparent, RMS current. Highest value since last reset of the alerts.
DEC sdbDevInActualVoltage	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.7	DeciVolt	read-only	The actual voltage.
DEC sdbDevInMinVoltage	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.8	DeciVolt	read-only	RMS voltage dip. Lowest value since reset of alerts.
I32 sdbDevInPowerVoltAmpere	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.9	Integer32	read-only	Calculated apparent power.
I32 sdbDevInPowerWatt	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.10	Integer32	read-only	Calculated real power.
DEC sdbDevInMaxAmps	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.11	DeciAmpere	read-write	Maximum current per input phase. Should last at least sdbDevStPeakDuration ms before triggering an alert.
I32 sdbDevInCTRatio	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.12	Integer32	read-write	The multiplier to use for the input CTs.
STR sdbDevInName	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.13	DisplayString	read-write	User configurable naming of inputs or phases.
INT sdbDevInZeroKWhSubtotal	1.3.6.1.4.1.31034.12.1.1.2.6.1.1.14	INTEGER	read-write	Reset input kWh subtotal counter of a single input to zero.
sdbDevOutlet	1.3.6.1.4.1.31034.12.1.1.2.7
sdbDevOutTable	1.3.6.1.4.1.31034.12.1.1.2.7.1		not-accessible	A table containing information of outlets of devices connected to the databus.
sdbDevOutEntry	1.3.6.1.4.1.31034.12.1.1.2.7.1.1		not-accessible	Outlets entry containing objects of an outlet of a particular databus device. Note that this table has two indexes. sdbDevIdIndex to identify a particular device and sdbDevOutIndex to identify a particular outlet of the device identified by sdbDevIdIndex.
I32 sdbDevOutIndex	1.3.6.1.4.1.31034.12.1.1.2.7.1.1.1	Integer32	not-accessible	A unique value for each outlet. Its value ranges between 1 and the value of sdbDevCfOutletsTotal.
STR sdbDevOutName	1.3.6.1.4.1.31034.12.1.1.2.7.1.1.2	DisplayString	read-write	User configurable naming of individual outlets.
sdbDevOutMtTable	1.3.6.1.4.1.31034.12.1.1.2.7.2		not-accessible	A table containing information of metered outlets of devices connected to the databus.
sdbDevOutMtEntry	1.3.6.1.4.1.31034.12.1.1.2.7.2.1		not-accessible	Metered outlets entry containing objects of a metered outlet of a particular databus device. Note that this table has two indexes. sdbDevIdIndex to identify a particular device and sdbDevOutMtIndex to identify a particular outlet of the device identified by sdbDevIdIndex.
I32 sdbDevOutMtIndex	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.1	Integer32	not-accessible	A unique value for each outlet. Its value ranges between 1 and the value of sdbDevCfOutletsMetered.
KIL sdbDevOutMtKWhTotal	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.2	KiloWattHour	read-only	Total kWh value of an outlet. This value can not be reset.
KIL sdbDevOutMtKWhSubtotal	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.3	KiloWattHour	read-only	Subotal kWh value of an outlet. This value can be reset.
DEC sdbDevOutMtPowerFactor	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.4	DeciPercent	read-only	Power factor of outlet. The power factor of an AC power system is defined as the ratio of the real or active power to the apparent power and is a number between 0 and 1. This number is expressed as a percentage between 0% and 100%.
DEC sdbDevOutMtActualCurrent	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.5	DeciAmpere	read-only	Actual apparent, RMS current.
DEC sdbDevOutMtPeakCurrent	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.6	DeciAmpere	read-only	Peak apparent, RMS current. Highest value since last reset of the alerts.
DEC sdbDevOutMtActualVoltage	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.7	DeciVolt	read-only	Actual voltage on outlet.
DEC sdbDevOutMtMaxAmps	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.8	DeciAmpere	read-write	Maximum current per outlet. Should last at least sdbDevStPeakDuration ms before triggering an alert.
I32 sdbDevOutMtCTRatio	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.9	Integer32	read-write	The multiplier to use for the outlet CTs.
I32 sdbDevOutMtPowerVoltAmpere	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.10	Integer32	read-only	Calculated apparent power.
I32 sdbDevOutMtPowerWatt	1.3.6.1.4.1.31034.12.1.1.2.7.2.1.11	Integer32	read-only	Calculated real power.
sdbDevOutSwTable	1.3.6.1.4.1.31034.12.1.1.2.7.3		not-accessible	A table containing information of switched outlets of devices connected to the databus.
sdbDevOutSwEntry	1.3.6.1.4.1.31034.12.1.1.2.7.3.1		not-accessible	Switched outlets entry containing objects of a switched outlet of a particular databus device. Note that this table has two indexes. sdbDevIdIndex to identify a particular device and sdbDevOutSwIndex to identify a particular outlet of the device identified by sdbDevIdIndex.
I32 sdbDevOutSwIndex	1.3.6.1.4.1.31034.12.1.1.2.7.3.1.1	Integer32	not-accessible	A unique value for each outlet. Its value ranges between 1 and the value of sdbDevCfOutletsSwitched.
INT sdbDevOutSwCurrentState	1.3.6.1.4.1.31034.12.1.1.2.7.3.1.2	INTEGER	read-write	The actual state of the outlet relay. Note that Writing is only effective after setting sdbDevOutSwUnlock.
INT sdbDevOutSwScheduled	1.3.6.1.4.1.31034.12.1.1.2.7.3.1.3	INTEGER	read-only	A one indicates pending activity; the switch delay has not yet expired.
INT sdbDevOutSwUnlock	1.3.6.1.4.1.31034.12.1.1.2.7.3.1.4	INTEGER	read-write	Switching and rebooting is unlocked for 10 seconds by writing a 1.
SEC sdbDevOutSwIndividualOutletDelay	1.3.6.1.4.1.31034.12.1.1.2.7.3.1.5	Second	read-write	Delay before an individual outlet switches on at power-up.
INT sdbDevOutSwReboot	1.3.6.1.4.1.31034.12.1.1.2.7.3.1.6	INTEGER	read-write	Reboot outlet relay if current state is on and outlet is unlocked; The outlet will be turned on after 10 seconds.
sdbDevSensor	1.3.6.1.4.1.31034.12.1.1.2.8
sdbDevMeasuresTable	1.3.6.1.4.1.31034.12.1.1.2.8.1		not-accessible	A table containing information of temperatures of devices connected to the databus.
sdbDevMeasuresEntry	1.3.6.1.4.1.31034.12.1.1.2.8.1.1		not-accessible	Device measures entry containing temperature information objects of a particular databus device.
DEC sdbDevMsIntTemperature	1.3.6.1.4.1.31034.12.1.1.2.8.1.1.1	DeciCelsius	read-only	Actual internal device temperature in deg C
DEC sdbDevMsExtTemperature	1.3.6.1.4.1.31034.12.1.1.2.8.1.1.2	DeciCelsius	read-only	Actual external device temperature sensor in deg C.
DEC sdbDevMsIntTemperaturePeak	1.3.6.1.4.1.31034.12.1.1.2.8.1.1.3	DeciCelsius	read-only	Peak internal device temperature since last reset of alerts.
DEC sdbDevMsExtTemperaturePeak	1.3.6.1.4.1.31034.12.1.1.2.8.1.1.4	DeciCelsius	read-only	Peak external device temperature since last reset of alerts.
sdbDevSnsTable	1.3.6.1.4.1.31034.12.1.1.2.8.2		not-accessible	A table containing information of sensors of devices connected to the databus.
sdbDevSnsEntry	1.3.6.1.4.1.31034.12.1.1.2.8.2.1		not-accessible	Sensors entry containing objects of a sensor of a particular databus device. Note that this table has two indexes. sdbDevIdIndex to identify a particular device and sdbDevSnsIndex to identify a particular sensor of the device identified by sdbDevIdIndex.
I32 sdbDevSnsIndex	1.3.6.1.4.1.31034.12.1.1.2.8.2.1.1	Integer32	not-accessible	A unique value for each sensor. Its value ranges between 1 and the value of sdbDevCfSensors.
STR sdbDevSnsType	1.3.6.1.4.1.31034.12.1.1.2.8.2.1.2	DisplayString	read-only	Type of connected sensor. T = Temperature (C) H = Humidity (%) I = dry switch contact
DEC sdbDevSnsValue	1.3.6.1.4.1.31034.12.1.1.2.8.2.1.3	DeciValue	read-only	Value of connected sensor
STR sdbDevSnsName	1.3.6.1.4.1.31034.12.1.1.2.8.2.1.4	DisplayString	read-write	User definable name for sensors.
sdbMIBConformance	1.3.6.1.4.1.31034.12.1.2
sdbMIBCompliances	1.3.6.1.4.1.31034.12.1.2.1
sdbMIBCompliance	1.3.6.1.4.1.31034.12.1.2.1.1			The requirements for conformance to the SCHLEIFENBAUER-DATABUS-MIB.
sdbMIBGroups	1.3.6.1.4.1.31034.12.1.2.2
sdbMIBNotificationGroup	1.3.6.1.4.1.31034.12.1.2.2.1			A collection of notifications.
sdbMIBDevIdGroup	1.3.6.1.4.1.31034.12.1.2.2.3			A collection of objects providing identification information about the device.
sdbMIBDevCfGroup	1.3.6.1.4.1.31034.12.1.2.2.4			A collection of objects providing configuration information about the device.
sdbMIBDevSsGroup	1.3.6.1.4.1.31034.12.1.2.2.5			A collection of objects providing status information about the device.
sdbMIBDevRsGroup	1.3.6.1.4.1.31034.12.1.2.2.6			Groups resettable attributes op the device.
sdbMIBDevStGroup	1.3.6.1.4.1.31034.12.1.2.2.7			A collection of objects providing the actual settings about the device.
sdbMIBDevInGroup	1.3.6.1.4.1.31034.12.1.2.2.8			A collection of objects providing the actual input measurements of the device.
sdbMIBDevOutGroup	1.3.6.1.4.1.31034.12.1.2.2.9			A collection of objects providing the actual outlet measurements of the device.
sdbMIBDevOutMtGroup	1.3.6.1.4.1.31034.12.1.2.2.10			A collection of objects providing the actual outlet measurements of the device.
sdbMIBDevOutSwGroup	1.3.6.1.4.1.31034.12.1.2.2.11			A collection of objects providing the actual outlet measurements of the device.
sdbMIBDevSensorGroup	1.3.6.1.4.1.31034.12.1.2.2.12			A collection of objects providing the actual environmental measurements of the device.
sdbMIBMgmtStatusGroup	1.3.6.1.4.1.31034.12.1.2.2.13			A collection of objects providing management status information about the databus.
sdbMIBMgmtControlGroup	1.3.6.1.4.1.31034.12.1.2.2.14			A collection of objects providing management control information about the databus.

RFC description

Schleifenbauer databus device MIB for network-enabled power and environmental monitoring equipment with alert management.

Start monitoring Schleifenbauer intelligent PDU, data center rack power distribution unit (databus ring topology health) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SCHLEIFENBAUER-DATABUS-MIB