All MIBs › Sentry4-MIB
Organization: Server Technology, Inc.
Last Updated: 2016-11-18
Category: Data Center Infrastructure Monitoring, Environmental and Power Monitoring, Intelligent PDU Management
Description: Manages Server Technology Sentry4 intelligent PDU outlet control, power metering, and branch monitoring.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Sentry4-MIB?
Sentry4-MIB is the vendor-specific Server Technology MIB module for the fourth-generation Sentry product family, covering the PRO1 and PRO2 series of Smart and Switched Cabinet/Power Distribution Units (CDU/PDU), registered under the serverTech enterprise branch (enterprises.1718.4). It models a multi-level power hierarchy — st4UnitConfigTable/st4UnitMonitorTable for each PDU unit (masterPdu, linkPdu, controller, or emcu type, with st4UnitStatus), st4InputCordConfigTable/MonitorTable for each AC input cord (st4InputCordActivePower, ApparentPower, PowerFactor, Energy, Frequency, OutOfBalance), st4LineConfigTable/MonitorTable for individual current-carrying lines (st4LineCurrent, LineCurrentUtilized), and st4PhaseConfigTable/MonitorTable for per-phase voltage, current, crest factor and power factor. Every measured quantity carries a companion DeviceStatus object whose enumeration (normal, breakerTripped, fuseBlown, lowAlarm/highAlarm, noComm, etc.) gives an immediate health verdict alongside the raw reading, which is what makes this MIB useful for rack-PDU power monitoring rather than just metering. It is deployed on Server Technology Sentry4 PRO1/PRO2 PDUs in data center cabinets, and administrators managing these units typically load Sentry4-MIB into an SNMP MIB Browser to poll outlet, line, and phase power data.
IPNetwork Monitor allows you to monitor SNMP objects defined in Sentry4-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Server Technology Sentry4 PRO1/PRO2 series Smart/Switched CDU and PDU
Monitoring Examples
An operator polls st4PhaseCurrent and st4PhaseCurrentStatus for each phase in st4PhaseMonitorTable on a 3-phase Sentry4 PDU; a st4PhaseCurrentStatus value of highAlarm alongside a current reading approaching the line's current capacity would indicate the phase is overloaded and at risk of tripping a breaker.
What Can Be Monitored
- per-unit status (masterPdu/linkPdu/controller/emcu)
- input cord power, power factor, and energy
- line current and current utilization
- phase voltage, current, and power factor
- DeviceStatus health enumerations (alarm/warning/breaker/fuse states)
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| DisplayString | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| serverTech | 1.3.6.1.4.1.1718 | |||
| sentry4 | 1.3.6.1.4.1.1718.4 | This is the MIB module for the fourth generation of the Sentry product family. This includes the PRO1 and PRO2 series of Smart and Switched Cabinet Distribution Unit (CDU) and Power Distribution Unit (PDU) products. | ||
| st4Objects | 1.3.6.1.4.1.1718.4.1 | |||
| st4System | 1.3.6.1.4.1.1718.4.1.1 | |||
| st4SystemConfig | 1.3.6.1.4.1.1718.4.1.1.1 | |||
| STR st4SystemProductName | 1.3.6.1.4.1.1718.4.1.1.1.1 | DisplayString | read-only | The product name. |
| STR st4SystemLocation | 1.3.6.1.4.1.1718.4.1.1.1.2 | DisplayString | read-write | The location of the system. |
| STR st4SystemFirmwareVersion | 1.3.6.1.4.1.1718.4.1.1.1.3 | DisplayString | read-only | The firmware version. |
| STR st4SystemFirmwareBuildInfo | 1.3.6.1.4.1.1718.4.1.1.1.4 | DisplayString | read-only | The firmware build information. |
| STR st4SystemNICSerialNumber | 1.3.6.1.4.1.1718.4.1.1.1.5 | DisplayString | read-only | The serial number of the network interface card. |
| STR st4SystemNICHardwareInfo | 1.3.6.1.4.1.1718.4.1.1.1.6 | DisplayString | read-only | Hardware information about the network interface card. |
| INT st4SystemProductSeries | 1.3.6.1.4.1.1718.4.1.1.1.7 | INTEGER | read-only | The product series. |
| BIT st4SystemFeatures | 1.3.6.1.4.1.1718.4.1.1.1.10 | Bits | read-only | The key-activated features enabled in the system. |
| STR st4SystemFeatureKey | 1.3.6.1.4.1.1718.4.1.1.1.11 | DisplayString | read-write | A valid feature key written to this object will enable a feature in the system. A valid feature key is in the form xxxx-xxxx-xxxx-xxxx. A read of this object returns an empty string. |
| I32 st4SystemConfigModifiedCount | 1.3.6.1.4.1.1718.4.1.1.1.20 | Integer32 | read-only | The total number of times the system configuration has changed. |
| I32 st4SystemUnitCount | 1.3.6.1.4.1.1718.4.1.1.1.21 | Integer32 | read-only | The number of units in the system. |
| st4Units | 1.3.6.1.4.1.1718.4.1.2 | |||
| st4UnitCommonConfig | 1.3.6.1.4.1.1718.4.1.2.1 | |||
| st4UnitConfigTable | 1.3.6.1.4.1.1718.4.1.2.2 | not-accessible | Unit configuration table. | |
| st4UnitConfigEntry | 1.3.6.1.4.1.1718.4.1.2.2.1 | not-accessible | Configuration objects for a particular unit. | |
| I32 st4UnitIndex | 1.3.6.1.4.1.1718.4.1.2.2.1.1 | Integer32 | not-accessible | Unit index. A=1, B=2, C=3, D=4, E=5, F=6. |
| STR st4UnitID | 1.3.6.1.4.1.1718.4.1.2.2.1.2 | DisplayString | read-only | The internal ID of the unit. Format=A. |
| STR st4UnitName | 1.3.6.1.4.1.1718.4.1.2.2.1.3 | DisplayString | read-write | The name of the unit. |
| STR st4UnitProductSN | 1.3.6.1.4.1.1718.4.1.2.2.1.4 | DisplayString | read-only | The product serial number of the unit. |
| STR st4UnitModel | 1.3.6.1.4.1.1718.4.1.2.2.1.5 | DisplayString | read-only | The model of the unit. |
| STR st4UnitAssetTag | 1.3.6.1.4.1.1718.4.1.2.2.1.6 | DisplayString | read-write | The asset tag of the unit. |
| INT st4UnitType | 1.3.6.1.4.1.1718.4.1.2.2.1.7 | INTEGER | read-only | The type of the unit. |
| BIT st4UnitCapabilities | 1.3.6.1.4.1.1718.4.1.2.2.1.8 | Bits | read-only | The capabilities of the unit. |
| STR st4UnitProductMfrDate | 1.3.6.1.4.1.1718.4.1.2.2.1.9 | DisplayString | read-only | The product manufacture date in YYYY-MM-DD (ISO 8601 format). |
| INT st4UnitDisplayOrientation | 1.3.6.1.4.1.1718.4.1.2.2.1.20 | INTEGER | read-write | The orientation of all displays in the unit. |
| INT st4UnitOutletSequenceOrder | 1.3.6.1.4.1.1718.4.1.2.2.1.21 | INTEGER | read-write | The sequencing order of all outlets in the unit. |
| I32 st4UnitInputCordCount | 1.3.6.1.4.1.1718.4.1.2.2.1.30 | Integer32 | read-only | The number of power input cords into the unit. |
| I32 st4UnitTempSensorCount | 1.3.6.1.4.1.1718.4.1.2.2.1.31 | Integer32 | read-only | The number of external temperature sensors supported by the unit. |
| I32 st4UnitHumidSensorCount | 1.3.6.1.4.1.1718.4.1.2.2.1.32 | Integer32 | read-only | The number of external humidity sensors supported by the unit. |
| I32 st4UnitWaterSensorCount | 1.3.6.1.4.1.1718.4.1.2.2.1.33 | Integer32 | read-only | The number of external water sensors supported by the unit. |
| I32 st4UnitCcSensorCount | 1.3.6.1.4.1.1718.4.1.2.2.1.34 | Integer32 | read-only | The number of external contact closure sensors supported by the unit. |
| I32 st4UnitAdcSensorCount | 1.3.6.1.4.1.1718.4.1.2.2.1.35 | Integer32 | read-only | The number of analog-to-digital converter sensors supported by the unit. |
| st4UnitMonitorTable | 1.3.6.1.4.1.1718.4.1.2.3 | not-accessible | Unit monitor table. | |
| st4UnitMonitorEntry | 1.3.6.1.4.1.1718.4.1.2.3.1 | not-accessible | Objects to monitor for a particular unit. | |
| DEV st4UnitStatus | 1.3.6.1.4.1.1718.4.1.2.3.1.1 | DeviceStatus | read-only | The status of the unit. |
| st4UnitEventConfigTable | 1.3.6.1.4.1.1718.4.1.2.4 | not-accessible | Unit event configuration table. | |
| st4UnitEventConfigEntry | 1.3.6.1.4.1.1718.4.1.2.4.1 | not-accessible | Event configuration objects for a particular unit. | |
| EVE st4UnitNotifications | 1.3.6.1.4.1.1718.4.1.2.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for unit events. |
| st4InputCords | 1.3.6.1.4.1.1718.4.1.3 | |||
| st4InputCordCommonConfig | 1.3.6.1.4.1.1718.4.1.3.1 | |||
| I32 st4InputCordActivePowerHysteresis | 1.3.6.1.4.1.1718.4.1.3.1.1 | Integer32 | read-write | The active power hysteresis of the input cord in Watts. |
| I32 st4InputCordApparentPowerHysteresis | 1.3.6.1.4.1.1718.4.1.3.1.2 | Integer32 | read-write | The apparent power hysteresis of the input cord in Volt-Amps. |
| I32 st4InputCordPowerFactorHysteresis | 1.3.6.1.4.1.1718.4.1.3.1.3 | Integer32 | read-write | The power factor hysteresis of the input cord in hundredths. |
| I32 st4InputCordOutOfBalanceHysteresis | 1.3.6.1.4.1.1718.4.1.3.1.4 | Integer32 | read-write | The 3 phase out-of-balance hysteresis of the input cord in percent. |
| st4InputCordConfigTable | 1.3.6.1.4.1.1718.4.1.3.2 | not-accessible | Input cord configuration table. | |
| st4InputCordConfigEntry | 1.3.6.1.4.1.1718.4.1.3.2.1 | not-accessible | Configuration objects for a particular input cord. | |
| I32 st4InputCordIndex | 1.3.6.1.4.1.1718.4.1.3.2.1.1 | Integer32 | not-accessible | Input cord index. A=1, B=2, C=3, D=4. |
| STR st4InputCordID | 1.3.6.1.4.1.1718.4.1.3.2.1.2 | DisplayString | read-only | The internal ID of the input cord. Format=AA. |
| STR st4InputCordName | 1.3.6.1.4.1.1718.4.1.3.2.1.3 | DisplayString | read-write | The name of the input cord. |
| STR st4InputCordInletType | 1.3.6.1.4.1.1718.4.1.3.2.1.6 | DisplayString | read-only | The type of plug on the input cord, or socket for the input cord. |
| I32 st4InputCordNominalVoltage | 1.3.6.1.4.1.1718.4.1.3.2.1.7 | Integer32 | read-write | The user-configured nominal voltage of the input cord in tenth Volts. |
| I32 st4InputCordNominalVoltageMin | 1.3.6.1.4.1.1718.4.1.3.2.1.8 | Integer32 | read-only | The factory-set minimum allowed for the user-configured nominal voltage of the input cord in Volts. |
| I32 st4InputCordNominalVoltageMax | 1.3.6.1.4.1.1718.4.1.3.2.1.9 | Integer32 | read-only | The factory-set maximum allowed for the user-configured nominal voltage of the input cord in Volts. |
| I32 st4InputCordCurrentCapacity | 1.3.6.1.4.1.1718.4.1.3.2.1.10 | Integer32 | read-write | The user-configured current capacity of the input cord in Amps. |
| I32 st4InputCordCurrentCapacityMax | 1.3.6.1.4.1.1718.4.1.3.2.1.11 | Integer32 | read-only | The factory-set maximum allowed for the user-configured current capacity of the input cord in Amps. |
| I32 st4InputCordPowerCapacity | 1.3.6.1.4.1.1718.4.1.3.2.1.12 | Integer32 | read-only | The power capacity of the input cord in Volt-Amps. For DC products, this is identical to power capacity in Watts. |
| I32 st4InputCordNominalPowerFactor | 1.3.6.1.4.1.1718.4.1.3.2.1.13 | Integer32 | read-write | The user-configured estimated nominal power factor of the input cord in hundredths. |
| I32 st4InputCordLineCount | 1.3.6.1.4.1.1718.4.1.3.2.1.20 | Integer32 | read-only | The number of current-carrying lines in the input cord. |
| I32 st4InputCordPhaseCount | 1.3.6.1.4.1.1718.4.1.3.2.1.21 | Integer32 | read-only | The number of active phases from the lines in the input cord. |
| I32 st4InputCordOcpCount | 1.3.6.1.4.1.1718.4.1.3.2.1.22 | Integer32 | read-only | The number of over-current protectors downstream from the input cord. |
| I32 st4InputCordBranchCount | 1.3.6.1.4.1.1718.4.1.3.2.1.23 | Integer32 | read-only | The number of branches downstream from the input cord. |
| I32 st4InputCordOutletCount | 1.3.6.1.4.1.1718.4.1.3.2.1.24 | Integer32 | read-only | The number of outlets powered from the input cord. |
| st4InputCordMonitorTable | 1.3.6.1.4.1.1718.4.1.3.3 | not-accessible | Input cord monitor table. | |
| st4InputCordMonitorEntry | 1.3.6.1.4.1.1718.4.1.3.3.1 | not-accessible | Objects to monitor for a particular input cord. | |
| DEV st4InputCordState | 1.3.6.1.4.1.1718.4.1.3.3.1.1 | DeviceState | read-only | The on/off state of the input cord. |
| DEV st4InputCordStatus | 1.3.6.1.4.1.1718.4.1.3.3.1.2 | DeviceStatus | read-only | The status of the input cord. |
| I32 st4InputCordActivePower | 1.3.6.1.4.1.1718.4.1.3.3.1.3 | Integer32 | read-only | The measured active power of the input cord in Watts. |
| DEV st4InputCordActivePowerStatus | 1.3.6.1.4.1.1718.4.1.3.3.1.4 | DeviceStatus | read-only | The status of the measured active power of the input cord. |
| I32 st4InputCordApparentPower | 1.3.6.1.4.1.1718.4.1.3.3.1.5 | Integer32 | read-only | The measured apparent power of the input cord in Volt-Amps. |
| DEV st4InputCordApparentPowerStatus | 1.3.6.1.4.1.1718.4.1.3.3.1.6 | DeviceStatus | read-only | The status of the measured apparent power of the input cord. |
| I32 st4InputCordPowerUtilized | 1.3.6.1.4.1.1718.4.1.3.3.1.7 | Integer32 | read-only | The amount of the input cord power capacity used in tenth percent. For AC products, this is the ratio of the apparent power to the power capacity. For DC products, this is the ratio of the active power to the power capacity. |
| I32 st4InputCordPowerFactor | 1.3.6.1.4.1.1718.4.1.3.3.1.8 | Integer32 | read-only | The measured power factor of the input cord in hundredths. |
| DEV st4InputCordPowerFactorStatus | 1.3.6.1.4.1.1718.4.1.3.3.1.9 | DeviceStatus | read-only | The status of the measured power factor of the input cord. |
| I32 st4InputCordEnergy | 1.3.6.1.4.1.1718.4.1.3.3.1.10 | Integer32 | read-only | The total energy consumption of loads through the input cord in tenth Kilowatt-Hours. |
| I32 st4InputCordFrequency | 1.3.6.1.4.1.1718.4.1.3.3.1.11 | Integer32 | read-only | The frequency of the input cord voltage in tenth Hertz. |
| I32 st4InputCordOutOfBalance | 1.3.6.1.4.1.1718.4.1.3.3.1.12 | Integer32 | read-only | The current imbalance on the lines of the input cord in tenth percent. |
| DEV st4InputCordOutOfBalanceStatus | 1.3.6.1.4.1.1718.4.1.3.3.1.13 | DeviceStatus | read-only | The status of the current imbalance on the lines of the input cord. |
| st4InputCordEventConfigTable | 1.3.6.1.4.1.1718.4.1.3.4 | not-accessible | Input cord event configuration table. | |
| st4InputCordEventConfigEntry | 1.3.6.1.4.1.1718.4.1.3.4.1 | not-accessible | Event configuration objects for a particular input cord. | |
| EVE st4InputCordNotifications | 1.3.6.1.4.1.1718.4.1.3.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for input cord events. |
| I32 st4InputCordActivePowerLowAlarm | 1.3.6.1.4.1.1718.4.1.3.4.1.2 | Integer32 | read-write | The active power low alarm threshold of the input cord in Watts. |
| I32 st4InputCordActivePowerLowWarning | 1.3.6.1.4.1.1718.4.1.3.4.1.3 | Integer32 | read-write | The active power low warning threshold of the input cord in Watts. |
| I32 st4InputCordActivePowerHighWarning | 1.3.6.1.4.1.1718.4.1.3.4.1.4 | Integer32 | read-write | The active power high warning threshold of the input cord in Watts. |
| I32 st4InputCordActivePowerHighAlarm | 1.3.6.1.4.1.1718.4.1.3.4.1.5 | Integer32 | read-write | The active power high alarm threshold of the input cord in Watts. |
| I32 st4InputCordApparentPowerLowAlarm | 1.3.6.1.4.1.1718.4.1.3.4.1.6 | Integer32 | read-write | The apparent power low alarm threshold of the input cord in Volt-Amps. |
| I32 st4InputCordApparentPowerLowWarning | 1.3.6.1.4.1.1718.4.1.3.4.1.7 | Integer32 | read-write | The apparent power low warning threshold of the input cord in Volt-Amps. |
| I32 st4InputCordApparentPowerHighWarning | 1.3.6.1.4.1.1718.4.1.3.4.1.8 | Integer32 | read-write | The apparent power high warning threshold of the input cord in Volt-Amps. |
| I32 st4InputCordApparentPowerHighAlarm | 1.3.6.1.4.1.1718.4.1.3.4.1.9 | Integer32 | read-write | The apparent power high alarm threshold of the input cord in Volt-Amps. |
| I32 st4InputCordPowerFactorLowAlarm | 1.3.6.1.4.1.1718.4.1.3.4.1.10 | Integer32 | read-write | The power factor low alarm threshold of the input cord in hundredths. |
| I32 st4InputCordPowerFactorLowWarning | 1.3.6.1.4.1.1718.4.1.3.4.1.11 | Integer32 | read-write | The power factor low warning threshold of the input cord in hundredths. |
| I32 st4InputCordOutOfBalanceHighWarning | 1.3.6.1.4.1.1718.4.1.3.4.1.12 | Integer32 | read-write | The 3 phase out-of-balance high warning threshold of the input cord in percent. |
| I32 st4InputCordOutOfBalanceHighAlarm | 1.3.6.1.4.1.1718.4.1.3.4.1.13 | Integer32 | read-write | The 3 phase out-of-balance high alarm threshold of the input cord in percent. |
| st4Lines | 1.3.6.1.4.1.1718.4.1.4 | |||
| st4LineCommonConfig | 1.3.6.1.4.1.1718.4.1.4.1 | |||
| I32 st4LineCurrentHysteresis | 1.3.6.1.4.1.1718.4.1.4.1.1 | Integer32 | read-write | The current hysteresis of the line in tenth Amps. |
| st4LineConfigTable | 1.3.6.1.4.1.1718.4.1.4.2 | not-accessible | Line configuration table. | |
| st4LineConfigEntry | 1.3.6.1.4.1.1718.4.1.4.2.1 | not-accessible | Configuration objects for a particular line. | |
| I32 st4LineIndex | 1.3.6.1.4.1.1718.4.1.4.2.1.1 | Integer32 | not-accessible | Line index. L1=1, L2=2, L3=3, N=4. |
| STR st4LineID | 1.3.6.1.4.1.1718.4.1.4.2.1.2 | DisplayString | read-only | The internal ID of the line. Format=AAN. |
| STR st4LineLabel | 1.3.6.1.4.1.1718.4.1.4.2.1.4 | DisplayString | read-only | The system label assigned to the line for identification. |
| I32 st4LineCurrentCapacity | 1.3.6.1.4.1.1718.4.1.4.2.1.6 | Integer32 | read-only | The current capacity of the line in Amps. |
| st4LineMonitorTable | 1.3.6.1.4.1.1718.4.1.4.3 | not-accessible | Line monitor table. | |
| st4LineMonitorEntry | 1.3.6.1.4.1.1718.4.1.4.3.1 | not-accessible | Objects to monitor for a particular line. | |
| DEV st4LineState | 1.3.6.1.4.1.1718.4.1.4.3.1.1 | DeviceState | read-only | The on/off state of the line. |
| DEV st4LineStatus | 1.3.6.1.4.1.1718.4.1.4.3.1.2 | DeviceStatus | read-only | The status of the line. |
| I32 st4LineCurrent | 1.3.6.1.4.1.1718.4.1.4.3.1.3 | Integer32 | read-only | The measured current on the line in hundredth Amps. |
| DEV st4LineCurrentStatus | 1.3.6.1.4.1.1718.4.1.4.3.1.4 | DeviceStatus | read-only | The status of the measured current on the line. |
| I32 st4LineCurrentUtilized | 1.3.6.1.4.1.1718.4.1.4.3.1.5 | Integer32 | read-only | The amount of the line current capacity used in tenth percent. |
| st4LineEventConfigTable | 1.3.6.1.4.1.1718.4.1.4.4 | not-accessible | Line event configuration table. | |
| st4LineEventConfigEntry | 1.3.6.1.4.1.1718.4.1.4.4.1 | not-accessible | Event configuration objects for a particular line. | |
| EVE st4LineNotifications | 1.3.6.1.4.1.1718.4.1.4.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for line events. |
| I32 st4LineCurrentLowAlarm | 1.3.6.1.4.1.1718.4.1.4.4.1.2 | Integer32 | read-write | The current low alarm threshold of the line in tenth Amps. |
| I32 st4LineCurrentLowWarning | 1.3.6.1.4.1.1718.4.1.4.4.1.3 | Integer32 | read-write | The current low warning threshold of the line in tenth Amps. |
| I32 st4LineCurrentHighWarning | 1.3.6.1.4.1.1718.4.1.4.4.1.4 | Integer32 | read-write | The current high warning threshold of the line in tenth Amps. |
| I32 st4LineCurrentHighAlarm | 1.3.6.1.4.1.1718.4.1.4.4.1.5 | Integer32 | read-write | The current high alarm threshold of the line in tenth Amps. |
| st4Phases | 1.3.6.1.4.1.1718.4.1.5 | |||
| st4PhaseCommonConfig | 1.3.6.1.4.1.1718.4.1.5.1 | |||
| I32 st4PhaseVoltageHysteresis | 1.3.6.1.4.1.1718.4.1.5.1.1 | Integer32 | read-write | The voltage hysteresis of the phase in tenth Volts. |
| I32 st4PhasePowerFactorHysteresis | 1.3.6.1.4.1.1718.4.1.5.1.2 | Integer32 | read-write | The power factor hysteresis of the phase in hundredths. |
| st4PhaseConfigTable | 1.3.6.1.4.1.1718.4.1.5.2 | not-accessible | Phase configuration table. | |
| st4PhaseConfigEntry | 1.3.6.1.4.1.1718.4.1.5.2.1 | not-accessible | Configuration objects for a particular phase. | |
| I32 st4PhaseIndex | 1.3.6.1.4.1.1718.4.1.5.2.1.1 | Integer32 | not-accessible | Phase index. Three-phase AC Wye: L1-N=1, L2-N=2, L3-N=3; Three-phase AC Delta: L1-L2=1, L2-L3=2, L3-L1=3; Single Phase: L1-R=1; DC: L1-R=1; Three-phase AC Wye & Delta: L1-N=1, L2-N=2, L3-N=3, L1-L2=4, L2-L3=5; L3-L1=6. |
| STR st4PhaseID | 1.3.6.1.4.1.1718.4.1.5.2.1.2 | DisplayString | read-only | The internal ID of the phase. Format=AAN. |
| STR st4PhaseLabel | 1.3.6.1.4.1.1718.4.1.5.2.1.4 | DisplayString | read-only | The system label assigned to the phase for identification. |
| I32 st4PhaseNominalVoltage | 1.3.6.1.4.1.1718.4.1.5.2.1.6 | Integer32 | read-only | The nominal voltage of the phase in tenth Volts. |
| I32 st4PhaseBranchCount | 1.3.6.1.4.1.1718.4.1.5.2.1.20 | Integer32 | read-only | The number of branches downstream from the phase. |
| I32 st4PhaseOutletCount | 1.3.6.1.4.1.1718.4.1.5.2.1.21 | Integer32 | read-only | The number of outlets powered from the phase. |
| st4PhaseMonitorTable | 1.3.6.1.4.1.1718.4.1.5.3 | not-accessible | Phase monitor table. | |
| st4PhaseMonitorEntry | 1.3.6.1.4.1.1718.4.1.5.3.1 | not-accessible | Objects to monitor for a particular phase. | |
| DEV st4PhaseState | 1.3.6.1.4.1.1718.4.1.5.3.1.1 | DeviceState | read-only | The on/off state of the phase. |
| DEV st4PhaseStatus | 1.3.6.1.4.1.1718.4.1.5.3.1.2 | DeviceStatus | read-only | The status of the phase. |
| I32 st4PhaseVoltage | 1.3.6.1.4.1.1718.4.1.5.3.1.3 | Integer32 | read-only | The measured voltage on the phase in tenth Volts. |
| DEV st4PhaseVoltageStatus | 1.3.6.1.4.1.1718.4.1.5.3.1.4 | DeviceStatus | read-only | The status of the measured voltage on the phase. |
| I32 st4PhaseVoltageDeviation | 1.3.6.1.4.1.1718.4.1.5.3.1.5 | Integer32 | read-only | The deviation from the nominal voltage on the phase in tenth percent. |
| I32 st4PhaseCurrent | 1.3.6.1.4.1.1718.4.1.5.3.1.6 | Integer32 | read-only | The measured current on the phase in hundredth Amps. |
| I32 st4PhaseCurrentCrestFactor | 1.3.6.1.4.1.1718.4.1.5.3.1.7 | Integer32 | read-only | The measured crest factor of the current waveform on the phase in tenths. |
| I32 st4PhaseActivePower | 1.3.6.1.4.1.1718.4.1.5.3.1.8 | Integer32 | read-only | The measured active power on the phase in Watts. |
| I32 st4PhaseApparentPower | 1.3.6.1.4.1.1718.4.1.5.3.1.9 | Integer32 | read-only | The measured apparent power on the phase in Volt-Amps. |
| I32 st4PhasePowerFactor | 1.3.6.1.4.1.1718.4.1.5.3.1.10 | Integer32 | read-only | The measured power factor on the phase in hundredths. |
| DEV st4PhasePowerFactorStatus | 1.3.6.1.4.1.1718.4.1.5.3.1.11 | DeviceStatus | read-only | The status of the measured power factor on the phase. |
| INT st4PhaseReactance | 1.3.6.1.4.1.1718.4.1.5.3.1.12 | INTEGER | read-only | The status of the measured reactance of the phase. |
| I32 st4PhaseEnergy | 1.3.6.1.4.1.1718.4.1.5.3.1.13 | Integer32 | read-only | The total energy consumption of loads through the phase in tenth Kilowatt-Hours. |
| st4PhaseEventConfigTable | 1.3.6.1.4.1.1718.4.1.5.4 | not-accessible | Phase event configuration table. | |
| st4PhaseEventConfigEntry | 1.3.6.1.4.1.1718.4.1.5.4.1 | not-accessible | Event configuration objects for a particular phase. | |
| EVE st4PhaseNotifications | 1.3.6.1.4.1.1718.4.1.5.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for phase events. |
| I32 st4PhaseVoltageLowAlarm | 1.3.6.1.4.1.1718.4.1.5.4.1.2 | Integer32 | read-write | The current low alarm threshold of the phase in tenth Volts. |
| I32 st4PhaseVoltageLowWarning | 1.3.6.1.4.1.1718.4.1.5.4.1.3 | Integer32 | read-write | The current low warning threshold of the phase in tenth Volts. |
| I32 st4PhaseVoltageHighWarning | 1.3.6.1.4.1.1718.4.1.5.4.1.4 | Integer32 | read-write | The current high warning threshold of the phase in tenth Volts. |
| I32 st4PhaseVoltageHighAlarm | 1.3.6.1.4.1.1718.4.1.5.4.1.5 | Integer32 | read-write | The current high alarm threshold of the phase in tenth Volts. |
| I32 st4PhasePowerFactorLowAlarm | 1.3.6.1.4.1.1718.4.1.5.4.1.6 | Integer32 | read-write | The low power factor alarm threshold of the phase in hundredths. |
| I32 st4PhasePowerFactorLowWarning | 1.3.6.1.4.1.1718.4.1.5.4.1.7 | Integer32 | read-write | The low power factor warning threshold of the phase in hundredths. |
| st4OverCurrentProtectors | 1.3.6.1.4.1.1718.4.1.6 | |||
| st4OcpCommonConfig | 1.3.6.1.4.1.1718.4.1.6.1 | |||
| st4OcpConfigTable | 1.3.6.1.4.1.1718.4.1.6.2 | not-accessible | Over-current protector configuration table. | |
| st4OcpConfigEntry | 1.3.6.1.4.1.1718.4.1.6.2.1 | not-accessible | Configuration objects for a particular over-current protector. | |
| I32 st4OcpIndex | 1.3.6.1.4.1.1718.4.1.6.2.1.1 | Integer32 | not-accessible | Over-current protector index. |
| STR st4OcpID | 1.3.6.1.4.1.1718.4.1.6.2.1.2 | DisplayString | read-only | The internal ID of the over-current protector. Format=AAN[N]. |
| STR st4OcpLabel | 1.3.6.1.4.1.1718.4.1.6.2.1.4 | DisplayString | read-only | The system label assigned to the over-current protector for identification. |
| INT st4OcpType | 1.3.6.1.4.1.1718.4.1.6.2.1.6 | INTEGER | read-only | The type of over-current protector. |
| I32 st4OcpCurrentCapacity | 1.3.6.1.4.1.1718.4.1.6.2.1.7 | Integer32 | read-write | The user-configured current capacity of the over-current protector in Amps. |
| I32 st4OcpCurrentCapacityMax | 1.3.6.1.4.1.1718.4.1.6.2.1.8 | Integer32 | read-only | The factory-set maximum allowed for the user-configured current capacity of the over-current protector in Amps. |
| I32 st4OcpBranchCount | 1.3.6.1.4.1.1718.4.1.6.2.1.20 | Integer32 | read-only | The number of branches downstream from the over-current protector. |
| I32 st4OcpOutletCount | 1.3.6.1.4.1.1718.4.1.6.2.1.21 | Integer32 | read-only | The number of outlets powered from the over-current protector. |
| st4OcpMonitorTable | 1.3.6.1.4.1.1718.4.1.6.3 | not-accessible | Over-current protector monitor table. | |
| st4OcpMonitorEntry | 1.3.6.1.4.1.1718.4.1.6.3.1 | not-accessible | Objects to monitor for a particular over-current protector. | |
| DEV st4OcpStatus | 1.3.6.1.4.1.1718.4.1.6.3.1.1 | DeviceStatus | read-only | The status of the over-current protector. |
| st4OcpEventConfigTable | 1.3.6.1.4.1.1718.4.1.6.4 | not-accessible | Over-current protector event configuration table. | |
| st4OcpEventConfigEntry | 1.3.6.1.4.1.1718.4.1.6.4.1 | not-accessible | Event configuration objects for a particular over-current protector. | |
| EVE st4OcpNotifications | 1.3.6.1.4.1.1718.4.1.6.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for over-current protector events. |
| st4Branches | 1.3.6.1.4.1.1718.4.1.7 | |||
| st4BranchCommonConfig | 1.3.6.1.4.1.1718.4.1.7.1 | |||
| I32 st4BranchCurrentHysteresis | 1.3.6.1.4.1.1718.4.1.7.1.1 | Integer32 | read-write | The current hysteresis of the branch in tenth Amps. |
| st4BranchConfigTable | 1.3.6.1.4.1.1718.4.1.7.2 | not-accessible | Branch configuration table. | |
| st4BranchConfigEntry | 1.3.6.1.4.1.1718.4.1.7.2.1 | not-accessible | Configuration objects for a particular branch. | |
| I32 st4BranchIndex | 1.3.6.1.4.1.1718.4.1.7.2.1.1 | Integer32 | not-accessible | Branch index. |
| STR st4BranchID | 1.3.6.1.4.1.1718.4.1.7.2.1.2 | DisplayString | read-only | The internal ID of the branch. Format=AAN[N]. |
| STR st4BranchLabel | 1.3.6.1.4.1.1718.4.1.7.2.1.4 | DisplayString | read-only | The system label assigned to the branch for identification. |
| I32 st4BranchCurrentCapacity | 1.3.6.1.4.1.1718.4.1.7.2.1.6 | Integer32 | read-only | The current capacity of the branch in Amps. |
| STR st4BranchPhaseID | 1.3.6.1.4.1.1718.4.1.7.2.1.20 | DisplayString | read-only | The internal ID of the phase powering this branch. Format=AAN. |
| STR st4BranchOcpID | 1.3.6.1.4.1.1718.4.1.7.2.1.21 | DisplayString | read-only | The internal ID of the over-current protector powering this outlet. Format=AAN[N]. |
| I32 st4BranchOutletCount | 1.3.6.1.4.1.1718.4.1.7.2.1.30 | Integer32 | read-only | The number of outlets powered from the branch. |
| st4BranchMonitorTable | 1.3.6.1.4.1.1718.4.1.7.3 | not-accessible | Branch monitor table. | |
| st4BranchMonitorEntry | 1.3.6.1.4.1.1718.4.1.7.3.1 | not-accessible | Objects to monitor for a particular branch. | |
| DEV st4BranchState | 1.3.6.1.4.1.1718.4.1.7.3.1.1 | DeviceState | read-only | The on/off state of the branch. |
| DEV st4BranchStatus | 1.3.6.1.4.1.1718.4.1.7.3.1.2 | DeviceStatus | read-only | The status of the branch. |
| I32 st4BranchCurrent | 1.3.6.1.4.1.1718.4.1.7.3.1.3 | Integer32 | read-only | The measured current on the branch in hundredth Amps. |
| DEV st4BranchCurrentStatus | 1.3.6.1.4.1.1718.4.1.7.3.1.4 | DeviceStatus | read-only | The status of the measured current on the branch. |
| I32 st4BranchCurrentUtilized | 1.3.6.1.4.1.1718.4.1.7.3.1.5 | Integer32 | read-only | The amount of the branch current capacity used in tenth percent. |
| st4BranchEventConfigTable | 1.3.6.1.4.1.1718.4.1.7.4 | not-accessible | Branch event configuration table. | |
| st4BranchEventConfigEntry | 1.3.6.1.4.1.1718.4.1.7.4.1 | not-accessible | Event configuration objects for a particular branch. | |
| EVE st4BranchNotifications | 1.3.6.1.4.1.1718.4.1.7.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for branch events. |
| I32 st4BranchCurrentLowAlarm | 1.3.6.1.4.1.1718.4.1.7.4.1.2 | Integer32 | read-write | The current low alarm threshold of the branch in tenth Amps. |
| I32 st4BranchCurrentLowWarning | 1.3.6.1.4.1.1718.4.1.7.4.1.3 | Integer32 | read-write | The current low warning threshold of the branch in tenth Amps. |
| I32 st4BranchCurrentHighWarning | 1.3.6.1.4.1.1718.4.1.7.4.1.4 | Integer32 | read-write | The current high warning threshold of the branch in tenth Amps. |
| I32 st4BranchCurrentHighAlarm | 1.3.6.1.4.1.1718.4.1.7.4.1.5 | Integer32 | read-write | The current high alarm threshold of the branch in tenth Amps. |
| st4Outlets | 1.3.6.1.4.1.1718.4.1.8 | |||
| st4OutletCommonConfig | 1.3.6.1.4.1.1718.4.1.8.1 | |||
| I32 st4OutletCurrentHysteresis | 1.3.6.1.4.1.1718.4.1.8.1.1 | Integer32 | read-write | The current hysteresis of the outlet in tenth Amps. |
| I32 st4OutletActivePowerHysteresis | 1.3.6.1.4.1.1718.4.1.8.1.2 | Integer32 | read-write | The power hysteresis of the outlet in Watts. |
| I32 st4OutletPowerFactorHysteresis | 1.3.6.1.4.1.1718.4.1.8.1.3 | Integer32 | read-write | The power factor hysteresis of the outlet in hundredths. |
| I32 st4OutletSequenceInterval | 1.3.6.1.4.1.1718.4.1.8.1.10 | Integer32 | read-write | The power-on sequencing interval for all outlets in seconds. |
| I32 st4OutletRebootDelay | 1.3.6.1.4.1.1718.4.1.8.1.11 | Integer32 | read-write | The reboot delay for all outlets in seconds. |
| INT st4OutletStateChangeLogging | 1.3.6.1.4.1.1718.4.1.8.1.12 | INTEGER | read-write | Enables or disables informational Outlet State Change event logging. |
| st4OutletConfigTable | 1.3.6.1.4.1.1718.4.1.8.2 | not-accessible | Outlet configuration table. | |
| st4OutletConfigEntry | 1.3.6.1.4.1.1718.4.1.8.2.1 | not-accessible | Configuration objects for a particular outlet. | |
| I32 st4OutletIndex | 1.3.6.1.4.1.1718.4.1.8.2.1.1 | Integer32 | not-accessible | Outlet index. |
| STR st4OutletID | 1.3.6.1.4.1.1718.4.1.8.2.1.2 | DisplayString | read-only | The internal ID of the outlet. Format=AAN[N[N]]. |
| STR st4OutletName | 1.3.6.1.4.1.1718.4.1.8.2.1.3 | DisplayString | read-write | The name of the outlet. |
| BIT st4OutletCapabilities | 1.3.6.1.4.1.1718.4.1.8.2.1.5 | Bits | read-only | The capabilities of the outlet. |
| STR st4OutletSocketType | 1.3.6.1.4.1.1718.4.1.8.2.1.6 | DisplayString | read-only | The socket type of the outlet. |
| I32 st4OutletCurrentCapacity | 1.3.6.1.4.1.1718.4.1.8.2.1.7 | Integer32 | read-only | The current capacity of the outlet in Amps. |
| I32 st4OutletPowerCapacity | 1.3.6.1.4.1.1718.4.1.8.2.1.8 | Integer32 | read-only | The power capacity of the outlet in Volt-Amps. For DC products, this is identical to power capacity in Watts. |
| INT st4OutletWakeupState | 1.3.6.1.4.1.1718.4.1.8.2.1.20 | INTEGER | read-write | The wakeup state of the outlet. |
| I32 st4OutletPostOnDelay | 1.3.6.1.4.1.1718.4.1.8.2.1.21 | Integer32 | read-write | The post-on delay of the outlet in seconds. |
| STR st4OutletPhaseID | 1.3.6.1.4.1.1718.4.1.8.2.1.30 | DisplayString | read-only | The internal ID of the phase powering this outlet. Format=AAN. |
| STR st4OutletOcpID | 1.3.6.1.4.1.1718.4.1.8.2.1.31 | DisplayString | read-only | The internal ID of the over-current protector powering this outlet. Format=AAN[N]. |
| STR st4OutletBranchID | 1.3.6.1.4.1.1718.4.1.8.2.1.32 | DisplayString | read-only | The internal ID of the branch powering this outlet. Format=AAN[N]. |
| st4OutletMonitorTable | 1.3.6.1.4.1.1718.4.1.8.3 | not-accessible | Outlet monitor table. | |
| st4OutletMonitorEntry | 1.3.6.1.4.1.1718.4.1.8.3.1 | not-accessible | Objects to monitor for a particular outlet. | |
| DEV st4OutletState | 1.3.6.1.4.1.1718.4.1.8.3.1.1 | DeviceState | read-only | The on/off state of the outlet. |
| DEV st4OutletStatus | 1.3.6.1.4.1.1718.4.1.8.3.1.2 | DeviceStatus | read-only | The status of the outlet. |
| I32 st4OutletCurrent | 1.3.6.1.4.1.1718.4.1.8.3.1.3 | Integer32 | read-only | The measured current on the outlet in hundredth Amps. |
| DEV st4OutletCurrentStatus | 1.3.6.1.4.1.1718.4.1.8.3.1.4 | DeviceStatus | read-only | The status of the measured current on the outlet. |
| I32 st4OutletCurrentUtilized | 1.3.6.1.4.1.1718.4.1.8.3.1.5 | Integer32 | read-only | The amount of the outlet current capacity used in tenth percent. |
| I32 st4OutletVoltage | 1.3.6.1.4.1.1718.4.1.8.3.1.6 | Integer32 | read-only | The measured voltage of the outlet in tenth Volts. |
| I32 st4OutletActivePower | 1.3.6.1.4.1.1718.4.1.8.3.1.7 | Integer32 | read-only | The measured active power of the outlet in Watts. |
| DEV st4OutletActivePowerStatus | 1.3.6.1.4.1.1718.4.1.8.3.1.8 | DeviceStatus | read-only | The status of the measured active power of the outlet. |
| I32 st4OutletApparentPower | 1.3.6.1.4.1.1718.4.1.8.3.1.9 | Integer32 | read-only | The measured apparent power of the outlet in Volt-Amps. |
| I32 st4OutletPowerFactor | 1.3.6.1.4.1.1718.4.1.8.3.1.10 | Integer32 | read-only | The measured power factor of the outlet in hundredths. |
| DEV st4OutletPowerFactorStatus | 1.3.6.1.4.1.1718.4.1.8.3.1.11 | DeviceStatus | read-only | The status of the measured power factor of the outlet. |
| I32 st4OutletCurrentCrestFactor | 1.3.6.1.4.1.1718.4.1.8.3.1.12 | Integer32 | read-only | The measured crest factor of the outlet in tenths. |
| INT st4OutletReactance | 1.3.6.1.4.1.1718.4.1.8.3.1.13 | INTEGER | read-only | The status of the measured reactance of the outlet. |
| I32 st4OutletEnergy | 1.3.6.1.4.1.1718.4.1.8.3.1.14 | Integer32 | read-only | The total energy consumption of the device plugged into the outlet in Watt-Hours. |
| st4OutletEventConfigTable | 1.3.6.1.4.1.1718.4.1.8.4 | not-accessible | Outlet event configuration table. | |
| st4OutletEventConfigEntry | 1.3.6.1.4.1.1718.4.1.8.4.1 | not-accessible | Event configuration objects for a particular outlet. | |
| EVE st4OutletNotifications | 1.3.6.1.4.1.1718.4.1.8.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for outlet events. |
| I32 st4OutletCurrentLowAlarm | 1.3.6.1.4.1.1718.4.1.8.4.1.2 | Integer32 | read-write | The current low alarm threshold of the outlet in tenth Amps. |
| I32 st4OutletCurrentLowWarning | 1.3.6.1.4.1.1718.4.1.8.4.1.3 | Integer32 | read-write | The current low warning threshold of the outlet in tenth Amps. |
| I32 st4OutletCurrentHighWarning | 1.3.6.1.4.1.1718.4.1.8.4.1.4 | Integer32 | read-write | The current high warning threshold of the outlet in tenth Amps. |
| I32 st4OutletCurrentHighAlarm | 1.3.6.1.4.1.1718.4.1.8.4.1.5 | Integer32 | read-write | The current high alarm threshold of the outlet in tenth Amps. |
| I32 st4OutletActivePowerLowAlarm | 1.3.6.1.4.1.1718.4.1.8.4.1.6 | Integer32 | read-write | The active power low alarm threshold of the outlet in Watts. |
| I32 st4OutletActivePowerLowWarning | 1.3.6.1.4.1.1718.4.1.8.4.1.7 | Integer32 | read-write | The active power low warning threshold of the outlet in Watts. |
| I32 st4OutletActivePowerHighWarning | 1.3.6.1.4.1.1718.4.1.8.4.1.8 | Integer32 | read-write | The active power high warning threshold of the outlet in Watts. |
| I32 st4OutletActivePowerHighAlarm | 1.3.6.1.4.1.1718.4.1.8.4.1.9 | Integer32 | read-write | The active power high alarm threshold of the outlet in Watts. |
| I32 st4OutletPowerFactorLowAlarm | 1.3.6.1.4.1.1718.4.1.8.4.1.10 | Integer32 | read-write | The low power factor alarm threshold of the outlet in hundredths. |
| I32 st4OutletPowerFactorLowWarning | 1.3.6.1.4.1.1718.4.1.8.4.1.11 | Integer32 | read-write | The low power factor warning threshold of the outlet in hundredths. |
| st4OutletControlTable | 1.3.6.1.4.1.1718.4.1.8.5 | not-accessible | Outlet control table. | |
| st4OutletControlEntry | 1.3.6.1.4.1.1718.4.1.8.5.1 | not-accessible | Objects for control of a particular outlet. | |
| INT st4OutletControlState | 1.3.6.1.4.1.1718.4.1.8.5.1.1 | INTEGER | read-only | The control state of the outlet. |
| INT st4OutletControlAction | 1.3.6.1.4.1.1718.4.1.8.5.1.2 | INTEGER | read-write | An action to change the control state of the outlet, or to queue an action. |
| st4OutletCommonControl | 1.3.6.1.4.1.1718.4.1.8.6 | |||
| INT st4OutletQueueControl | 1.3.6.1.4.1.1718.4.1.8.6.1 | INTEGER | read-write | An action to clear or commit queued outlet control actions. A read of this object returns clear(0) if queue is empty, and commit(1) if the queue is not empty. |
| st4TemperatureSensors | 1.3.6.1.4.1.1718.4.1.9 | |||
| st4TempSensorCommonConfig | 1.3.6.1.4.1.1718.4.1.9.1 | |||
| I32 st4TempSensorHysteresis | 1.3.6.1.4.1.1718.4.1.9.1.1 | Integer32 | read-write | The temperature hysteresis of the sensor in degrees, using the scale selected by st4TempSensorScale. |
| INT st4TempSensorScale | 1.3.6.1.4.1.1718.4.1.9.1.10 | INTEGER | read-write | The current scale used for all temperature values. |
| st4TempSensorConfigTable | 1.3.6.1.4.1.1718.4.1.9.2 | not-accessible | Temperature sensor configuration table. | |
| st4TempSensorConfigEntry | 1.3.6.1.4.1.1718.4.1.9.2.1 | not-accessible | Configuration objects for a particular temperature sensor. | |
| I32 st4TempSensorIndex | 1.3.6.1.4.1.1718.4.1.9.2.1.1 | Integer32 | not-accessible | Temperature sensor index. |
| STR st4TempSensorID | 1.3.6.1.4.1.1718.4.1.9.2.1.2 | DisplayString | read-only | The internal ID of the temperature sensor. Format=AN. |
| STR st4TempSensorName | 1.3.6.1.4.1.1718.4.1.9.2.1.3 | DisplayString | read-write | The name of the temperature sensor. |
| I32 st4TempSensorValueMin | 1.3.6.1.4.1.1718.4.1.9.2.1.4 | Integer32 | read-only | The minimum temperature limit of the sensor in degrees, using the scale selected by st4TempSensorScale. |
| I32 st4TempSensorValueMax | 1.3.6.1.4.1.1718.4.1.9.2.1.5 | Integer32 | read-only | The maximum temperature limit of the sensor in degrees, using the scale selected by st4TempSensorScale. |
| st4TempSensorMonitorTable | 1.3.6.1.4.1.1718.4.1.9.3 | not-accessible | Temperature sensor monitor table. | |
| st4TempSensorMonitorEntry | 1.3.6.1.4.1.1718.4.1.9.3.1 | not-accessible | Objects to monitor for a particular temperature sensor. | |
| I32 st4TempSensorValue | 1.3.6.1.4.1.1718.4.1.9.3.1.1 | Integer32 | read-only | The measured temperature on the sensor in tenth degrees using the scale selected by st4TempSensorScale. -410 means the temperature reading is invalid. |
| DEV st4TempSensorStatus | 1.3.6.1.4.1.1718.4.1.9.3.1.2 | DeviceStatus | read-only | The status of the temperature sensor. |
| st4TempSensorEventConfigTable | 1.3.6.1.4.1.1718.4.1.9.4 | not-accessible | Temperature sensor event configuration table. | |
| st4TempSensorEventConfigEntry | 1.3.6.1.4.1.1718.4.1.9.4.1 | not-accessible | Event configuration objects for a particular temperature sensor. | |
| EVE st4TempSensorNotifications | 1.3.6.1.4.1.1718.4.1.9.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for temperature sensor events. |
| I32 st4TempSensorLowAlarm | 1.3.6.1.4.1.1718.4.1.9.4.1.2 | Integer32 | read-write | The low alarm threshold of the temperature sensor in degrees. |
| I32 st4TempSensorLowWarning | 1.3.6.1.4.1.1718.4.1.9.4.1.3 | Integer32 | read-write | The low warning threshold of the temperature sensor in degrees. |
| I32 st4TempSensorHighWarning | 1.3.6.1.4.1.1718.4.1.9.4.1.4 | Integer32 | read-write | The high warning threshold of the temperature sensor in degrees. |
| I32 st4TempSensorHighAlarm | 1.3.6.1.4.1.1718.4.1.9.4.1.5 | Integer32 | read-write | The high alarm threshold of the temperature sensor in degrees. |
| st4HumiditySensors | 1.3.6.1.4.1.1718.4.1.10 | |||
| st4HumidSensorCommonConfig | 1.3.6.1.4.1.1718.4.1.10.1 | |||
| I32 st4HumidSensorHysteresis | 1.3.6.1.4.1.1718.4.1.10.1.1 | Integer32 | read-write | The humidity hysteresis of the sensor in percent relative humidity. |
| st4HumidSensorConfigTable | 1.3.6.1.4.1.1718.4.1.10.2 | not-accessible | Humidity sensor configuration table. | |
| st4HumidSensorConfigEntry | 1.3.6.1.4.1.1718.4.1.10.2.1 | not-accessible | Configuration objects for a particular humidity sensor. | |
| I32 st4HumidSensorIndex | 1.3.6.1.4.1.1718.4.1.10.2.1.1 | Integer32 | not-accessible | Humidity sensor index. |
| STR st4HumidSensorID | 1.3.6.1.4.1.1718.4.1.10.2.1.2 | DisplayString | read-only | The internal ID of the humidity sensor. Format=AN. |
| STR st4HumidSensorName | 1.3.6.1.4.1.1718.4.1.10.2.1.3 | DisplayString | read-write | The name of the humidity sensor. |
| st4HumidSensorMonitorTable | 1.3.6.1.4.1.1718.4.1.10.3 | not-accessible | Humidity sensor monitor table. | |
| st4HumidSensorMonitorEntry | 1.3.6.1.4.1.1718.4.1.10.3.1 | not-accessible | Objects to monitor for a particular humidity sensor. | |
| I32 st4HumidSensorValue | 1.3.6.1.4.1.1718.4.1.10.3.1.1 | Integer32 | read-only | The measured humidity on the sensor in percentage relative humidity. |
| DEV st4HumidSensorStatus | 1.3.6.1.4.1.1718.4.1.10.3.1.2 | DeviceStatus | read-only | The status of the humidity sensor. |
| st4HumidSensorEventConfigTable | 1.3.6.1.4.1.1718.4.1.10.4 | not-accessible | Humidity sensor event configuration table. | |
| st4HumidSensorEventConfigEntry | 1.3.6.1.4.1.1718.4.1.10.4.1 | not-accessible | Event configuration objects for a particular humidity sensor. | |
| EVE st4HumidSensorNotifications | 1.3.6.1.4.1.1718.4.1.10.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for humidity sensor events. |
| I32 st4HumidSensorLowAlarm | 1.3.6.1.4.1.1718.4.1.10.4.1.2 | Integer32 | read-write | The low alarm threshold of the humidity sensor in percentage relative humidity. |
| I32 st4HumidSensorLowWarning | 1.3.6.1.4.1.1718.4.1.10.4.1.3 | Integer32 | read-write | The low warning threshold of the humidity sensor in percentage relative humidity. |
| I32 st4HumidSensorHighWarning | 1.3.6.1.4.1.1718.4.1.10.4.1.4 | Integer32 | read-write | The high warning threshold of the humidity sensor in percentage relative humidity. |
| I32 st4HumidSensorHighAlarm | 1.3.6.1.4.1.1718.4.1.10.4.1.5 | Integer32 | read-write | The high alarm threshold of the humidity sensor in percentage relative humidity. |
| st4WaterSensors | 1.3.6.1.4.1.1718.4.1.11 | |||
| st4WaterSensorCommonConfig | 1.3.6.1.4.1.1718.4.1.11.1 | |||
| st4WaterSensorConfigTable | 1.3.6.1.4.1.1718.4.1.11.2 | not-accessible | Water sensor configuration table. | |
| st4WaterSensorConfigEntry | 1.3.6.1.4.1.1718.4.1.11.2.1 | not-accessible | Configuration objects for a particular water sensor. | |
| I32 st4WaterSensorIndex | 1.3.6.1.4.1.1718.4.1.11.2.1.1 | Integer32 | not-accessible | Water sensor index. |
| STR st4WaterSensorID | 1.3.6.1.4.1.1718.4.1.11.2.1.2 | DisplayString | read-only | The internal ID of the water sensor. Format=AN. |
| STR st4WaterSensorName | 1.3.6.1.4.1.1718.4.1.11.2.1.3 | DisplayString | read-write | The name of the water sensor. |
| st4WaterSensorMonitorTable | 1.3.6.1.4.1.1718.4.1.11.3 | not-accessible | Water sensor monitor table. | |
| st4WaterSensorMonitorEntry | 1.3.6.1.4.1.1718.4.1.11.3.1 | not-accessible | Objects to monitor for a particular water sensor. | |
| DEV st4WaterSensorStatus | 1.3.6.1.4.1.1718.4.1.11.3.1.1 | DeviceStatus | read-only | The status of the water sensor. |
| st4WaterSensorEventConfigTable | 1.3.6.1.4.1.1718.4.1.11.4 | not-accessible | Water sensor event configuration table. | |
| st4WaterSensorEventConfigEntry | 1.3.6.1.4.1.1718.4.1.11.4.1 | not-accessible | Event configuration objects for a particular water sensor. | |
| EVE st4WaterSensorNotifications | 1.3.6.1.4.1.1718.4.1.11.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for water sensor events. |
| st4ContactClosureSensors | 1.3.6.1.4.1.1718.4.1.12 | |||
| st4CcSensorCommonConfig | 1.3.6.1.4.1.1718.4.1.12.1 | |||
| st4CcSensorConfigTable | 1.3.6.1.4.1.1718.4.1.12.2 | not-accessible | Contact closure sensor configuration table. | |
| st4CcSensorConfigEntry | 1.3.6.1.4.1.1718.4.1.12.2.1 | not-accessible | Configuration objects for a particular contact closure sensor. | |
| I32 st4CcSensorIndex | 1.3.6.1.4.1.1718.4.1.12.2.1.1 | Integer32 | not-accessible | Contact closure sensor index. |
| STR st4CcSensorID | 1.3.6.1.4.1.1718.4.1.12.2.1.2 | DisplayString | read-only | The internal ID of the contact closure sensor. Format=AN. |
| STR st4CcSensorName | 1.3.6.1.4.1.1718.4.1.12.2.1.3 | DisplayString | read-write | The name of the contact closure sensor. |
| st4CcSensorMonitorTable | 1.3.6.1.4.1.1718.4.1.12.3 | not-accessible | Contact closure sensor monitor table. | |
| st4CcSensorMonitorEntry | 1.3.6.1.4.1.1718.4.1.12.3.1 | not-accessible | Objects to monitor for a particular contact closure sensor. | |
| DEV st4CcSensorStatus | 1.3.6.1.4.1.1718.4.1.12.3.1.1 | DeviceStatus | read-only | The status of the contact closure. |
| st4CcSensorEventConfigTable | 1.3.6.1.4.1.1718.4.1.12.4 | not-accessible | Contact closure sensor event configuration table. | |
| st4CcSensorEventConfigEntry | 1.3.6.1.4.1.1718.4.1.12.4.1 | not-accessible | Event configuration objects for a particular contact closure sensor. | |
| EVE st4CcSensorNotifications | 1.3.6.1.4.1.1718.4.1.12.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for contact closure sensor events. |
| st4AnalogToDigitalConvSensors | 1.3.6.1.4.1.1718.4.1.13 | |||
| st4AdcSensorCommonConfig | 1.3.6.1.4.1.1718.4.1.13.1 | |||
| I32 st4AdcSensorHysteresis | 1.3.6.1.4.1.1718.4.1.13.1.1 | Integer32 | read-write | The 8-bit count hysteresis of the analog-to-digital converter sensor. |
| st4AdcSensorConfigTable | 1.3.6.1.4.1.1718.4.1.13.2 | not-accessible | Analog-to-digital converter sensor configuration table. | |
| st4AdcSensorConfigEntry | 1.3.6.1.4.1.1718.4.1.13.2.1 | not-accessible | Configuration objects for a particular analog-to-digital converter sensor. | |
| I32 st4AdcSensorIndex | 1.3.6.1.4.1.1718.4.1.13.2.1.1 | Integer32 | not-accessible | Analog-to-digital converter sensor index. |
| STR st4AdcSensorID | 1.3.6.1.4.1.1718.4.1.13.2.1.2 | DisplayString | read-only | The internal ID of the analog-to-digital converter sensor. Format=AN. |
| STR st4AdcSensorName | 1.3.6.1.4.1.1718.4.1.13.2.1.3 | DisplayString | read-write | The name of the analog-to-digital converter sensor. |
| st4AdcSensorMonitorTable | 1.3.6.1.4.1.1718.4.1.13.3 | not-accessible | Analog-to-digital converter sensor monitor table. | |
| st4AdcSensorMonitorEntry | 1.3.6.1.4.1.1718.4.1.13.3.1 | not-accessible | Objects to monitor for a particular analog-to-digital converter sensor. | |
| I32 st4AdcSensorValue | 1.3.6.1.4.1.1718.4.1.13.3.1.1 | Integer32 | read-only | The 8-bit value from the analog-to-digital converter sensor. |
| DEV st4AdcSensorStatus | 1.3.6.1.4.1.1718.4.1.13.3.1.2 | DeviceStatus | read-only | The status of the analog-to-digital converter sensor. |
| st4AdcSensorEventConfigTable | 1.3.6.1.4.1.1718.4.1.13.4 | not-accessible | Analog-to-digital converter sensor event configuration table. | |
| st4AdcSensorEventConfigEntry | 1.3.6.1.4.1.1718.4.1.13.4.1 | not-accessible | Event configuration objects for a particular analog-to-digital converter sensor. | |
| EVE st4AdcSensorNotifications | 1.3.6.1.4.1.1718.4.1.13.4.1.1 | EventNotificationMethods | read-write | The notification methods enabled for analog-to-digital converter sensor events. |
| I32 st4AdcSensorLowAlarm | 1.3.6.1.4.1.1718.4.1.13.4.1.2 | Integer32 | read-write | The 8-bit value for the low alarm threshold of the analog-to-digital converter sensor. |
| I32 st4AdcSensorLowWarning | 1.3.6.1.4.1.1718.4.1.13.4.1.3 | Integer32 | read-write | The 8-bit value for the low warning threshold of the analog-to-digital converter sensor. |
| I32 st4AdcSensorHighWarning | 1.3.6.1.4.1.1718.4.1.13.4.1.4 | Integer32 | read-write | The 8-bit value for the high warning threshold of the analog-to-digital converter sensor. |
| I32 st4AdcSensorHighAlarm | 1.3.6.1.4.1.1718.4.1.13.4.1.5 | Integer32 | read-write | The 8-bit value for the high alarm threshold of the analog-to-digital converter sensor. |
| st4EventInformation | 1.3.6.1.4.1.1718.4.1.99 | |||
| STR st4EventStatusText | 1.3.6.1.4.1.1718.4.1.99.1 | DisplayString | read-only | The text representation of the enumerated integer value of the most-relevant status or state object included in a trap. The value of this object is set only when sent with a trap. A read of this object will return a NULL string. |
| INT st4EventStatusCondition | 1.3.6.1.4.1.1718.4.1.99.2 | INTEGER | read-only | The condition of the enumerated integer value of the status object included in a trap. The value of this object is set only when sent with a trap. A read of this object will return zero. |
| st4Notifications | 1.3.6.1.4.1.1718.4.100 | |||
| st4Events | 1.3.6.1.4.1.1718.4.100.0 | |||
| NTF st4UnitStatusEvent | 1.3.6.1.4.1.1718.4.100.0.1 | Unit status event. | ||
| NTF st4InputCordStatusEvent | 1.3.6.1.4.1.1718.4.100.0.2 | Input cord status event. | ||
| NTF st4InputCordActivePowerEvent | 1.3.6.1.4.1.1718.4.100.0.3 | Input cord active power event. | ||
| NTF st4InputCordApparentPowerEvent | 1.3.6.1.4.1.1718.4.100.0.4 | Input cord apparent power event. | ||
| NTF st4InputCordPowerFactorEvent | 1.3.6.1.4.1.1718.4.100.0.5 | Input cord power factor event. | ||
| NTF st4InputCordOutOfBalanceEvent | 1.3.6.1.4.1.1718.4.100.0.6 | Input cord out-of-balance event. | ||
| NTF st4LineStatusEvent | 1.3.6.1.4.1.1718.4.100.0.7 | Line status event. | ||
| NTF st4LineCurrentEvent | 1.3.6.1.4.1.1718.4.100.0.8 | Line current event. | ||
| NTF st4PhaseStatusEvent | 1.3.6.1.4.1.1718.4.100.0.9 | Phase status event. | ||
| NTF st4PhaseVoltageEvent | 1.3.6.1.4.1.1718.4.100.0.10 | Phase voltage event. | ||
| NTF st4PhasePowerFactorEvent | 1.3.6.1.4.1.1718.4.100.0.11 | Phase voltage event. | ||
| NTF st4OcpStatusEvent | 1.3.6.1.4.1.1718.4.100.0.12 | Over-current protector status event. | ||
| NTF st4BranchStatusEvent | 1.3.6.1.4.1.1718.4.100.0.13 | Branch status event. | ||
| NTF st4BranchCurrentEvent | 1.3.6.1.4.1.1718.4.100.0.14 | Branch current event. | ||
| NTF st4OutletStatusEvent | 1.3.6.1.4.1.1718.4.100.0.15 | Outlet status event. | ||
| NTF st4OutletStateChangeEvent | 1.3.6.1.4.1.1718.4.100.0.16 | Outlet state change event. | ||
| NTF st4OutletCurrentEvent | 1.3.6.1.4.1.1718.4.100.0.17 | Outlet current event. | ||
| NTF st4OutletActivePowerEvent | 1.3.6.1.4.1.1718.4.100.0.18 | Outlet active power event. | ||
| NTF st4OutletPowerFactorEvent | 1.3.6.1.4.1.1718.4.100.0.19 | Outlet power factor event. | ||
| NTF st4TempSensorEvent | 1.3.6.1.4.1.1718.4.100.0.20 | Temperature sensor event. | ||
| NTF st4HumidSensorEvent | 1.3.6.1.4.1.1718.4.100.0.21 | Humidity sensor event. | ||
| NTF st4WaterSensorStatusEvent | 1.3.6.1.4.1.1718.4.100.0.22 | Water sensor status event. | ||
| NTF st4CcSensorStatusEvent | 1.3.6.1.4.1.1718.4.100.0.23 | Contact closure sensor status event. | ||
| NTF st4AdcSensorEvent | 1.3.6.1.4.1.1718.4.100.0.24 | Analog-to-digital converter sensor event. | ||
| st4Conformance | 1.3.6.1.4.1.1718.4.200 | |||
| st4Groups | 1.3.6.1.4.1.1718.4.200.1 | |||
| st4SystemObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.1 | System objects group. | ||
| st4UnitObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.2 | Unit objects group. | ||
| st4InputCordObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.3 | Input cord objects group. | ||
| st4LineObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.4 | Line objects group. | ||
| st4PhaseObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.5 | Phase objects group. | ||
| st4OcpObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.6 | Over-current protector objects group. | ||
| st4BranchObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.7 | Branch objects group. | ||
| st4OutletObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.8 | Outlet objects group. | ||
| st4TempSensorObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.9 | Temperature sensor objects group. | ||
| st4HumidSensorObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.10 | Humidity sensor objects group. | ||
| st4WaterSensorObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.11 | Water sensor objects group. | ||
| st4CcSensorObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.12 | Contact closure sensor objects group. | ||
| st4AdcSensorObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.13 | Analog-to-digital converter sensor objects group. | ||
| st4EventInfoObjectsGroup | 1.3.6.1.4.1.1718.4.200.1.99 | Event information objects group. | ||
| st4EventNotificationsGroup | 1.3.6.1.4.1.1718.4.200.1.100 | Event notifications group. | ||
| st4Compliances | 1.3.6.1.4.1.1718.4.200.2 | |||
| st4ModuleCompliances | 1.3.6.1.4.1.1718.4.200.2.1 | The requirements for conformance to the Sentry4-MIB. |
RFC description
Manages Server Technology Sentry4 product family (PRO1/PRO2 series) Smart and Switched Cabinet/Power Distribution Units (CDU/PDU) including power monitoring, temperature sensors, and environmental controls.
Start monitoring Server Technology Sentry4 PRO1/PRO2 series Smart/Switched CDU and PDU (per-line/phase power/status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.