SCA-IPROUTER-MIB

All MIBs › SCA-IPROUTER-MIB

Category: Securicor WAN Router Management, WAN and Routing

Description: Manages Securicor Arisoft WAN router IP routing table, static routes, and protocol parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SCA-IPROUTER-MIB?

SCA-IPROUTER-MIB is a vendor-private IP router MIB whose enterprise OID tree (iprouter, under scanet from SCANET-MIB) points to Securicor Arisoft's WAN router product line, though the copyright notice embedded in the file text ("Copyright (C) 1997 Intel Corporation") appears to be inherited from a shared IP-router MIB template rather than reflecting actual Intel authorship of this module. It models per-link IP configuration (confIfTable: address/mask pairs, RIP version and metric, RIP-2 authentication, BOOTP forwarding, proxy ARP), packet filtering rules (filterTable: protocol, TCP flags, source/destination address and port matching with pass/discard actions), NAT bindings (natTable), and static routes (statRoutTable), alongside per-interface statistics tables for IP, ICMP, ARP, RIP, BOOTP, and octet counters broken out by protocol (FTP, Telnet, SMTP, DNS, HTTP, SNMP, RIP, tunnel). This makes it useful for both configuring WAN router interfaces and monitoring per-protocol traffic volume and error counts on each link. It depends on the underlying IP router's link-layer interface table for its confIfIndex numbering, and is deployed on Securicor Arisoft WAN routers, and the full SCA-IPROUTER-MIB reference documents every configuration and statistics object listed above.

IPNetwork Monitor allows you to monitor SNMP objects defined in SCA-IPROUTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Securicor Arisoft WAN routers

Monitoring Examples

An operator polls statIfState to confirm an IP link is up and cross-references ripIfInAuthFails and ripIfInBadVers to spot RIP-2 authentication or version mismatches with a neighboring router; a climbing ipIfOutDiscards counter alongside filterHits on a restrictive filter entry would indicate that packets are being silently dropped by a misconfigured IP filter rather than a genuine network fault.

What Can Be Monitored

per-link IP/ICMP/ARP/RIP/BOOTP packet counters
IP filter rule hit counts
NAT binding table entries
static route table entries
per-protocol octet counters (FTP, HTTP, SNMP, RIP, tunnel, etc.)

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress

From SCANET-MIB

scanet

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
iprouter	1.3.6.1.4.1.208.42
conf	1.3.6.1.4.1.208.42.1
confIfTable	1.3.6.1.4.1.208.42.1.1		not-accessible	The table contains configuration information for each IP link.
confIfEntry	1.3.6.1.4.1.208.42.1.1.1		not-accessible	Configuration information for the IP link.
INT confIfIndex	1.3.6.1.4.1.208.42.1.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
OCT confIfAddrAndMask1	1.3.6.1.4.1.208.42.1.1.1.2	OCTET STRING	read-write	The primary IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask. A string of all zeros is used for unnumbered links.
OCT confIfAddrAndMask2	1.3.6.1.4.1.208.42.1.1.1.3	OCTET STRING	read-write	The second IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask.
OCT confIfAddrAndMask3	1.3.6.1.4.1.208.42.1.1.1.4	OCTET STRING	read-write	The third IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask.
OCT confIfAddrAndMask4	1.3.6.1.4.1.208.42.1.1.1.5	OCTET STRING	read-write	The fourth IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask.
INT confIfRouteProto	1.3.6.1.4.1.208.42.1.1.1.6	INTEGER	read-write	The Routing Protocol used on the link.
INT confIfTrigRip	1.3.6.1.4.1.208.42.1.1.1.7	INTEGER	read-write	Indicates whether Triggered RIP is used on the link.
INT confIfRipMetric	1.3.6.1.4.1.208.42.1.1.1.8	INTEGER	read-write	The RIP metric used on the link.
INT confIfRip2AuthType	1.3.6.1.4.1.208.42.1.1.1.9	INTEGER	read-write	The RIP-2 Authentication type used on the link.
OCT confIfRip2AuthKey	1.3.6.1.4.1.208.42.1.1.1.10	OCTET STRING	read-write	The authentication key used in RIP-2.
INT confIfBootpReqForw	1.3.6.1.4.1.208.42.1.1.1.11	INTEGER	read-write	Indicates whether BOOTP requests are forwarded on the link
INT confIfProxyArp	1.3.6.1.4.1.208.42.1.1.1.12	INTEGER	read-write	Indicates whether Proxy Arp is used on the link.
INT confIfFiltering	1.3.6.1.4.1.208.42.1.1.1.13	INTEGER	read-write	Indicates whether IP filtering is used on the link.
INT confIfRxDefAction	1.3.6.1.4.1.208.42.1.1.1.14	INTEGER	read-write	Indicates whether packets not matching any of the Rx filters on the link must be passed or discarded.
INT confIfTxDefAction	1.3.6.1.4.1.208.42.1.1.1.15	INTEGER	read-write	Indicates whether packets not matching any of the Tx filters on the link must be passed or discarded.
INT confIfRxDefLogging	1.3.6.1.4.1.208.42.1.1.1.16	INTEGER	read-write	Indicates whether packets not matching any of the Rx filters must be logged.
INT confIfTxDefLogging	1.3.6.1.4.1.208.42.1.1.1.17	INTEGER	read-write	Indicates whether packets not matching any of the Tx filters must be logged.
OCT confIfCreateObj	1.3.6.1.4.1.208.42.1.1.1.18	OCTET STRING	read-write	Create a non existing table entry. If the entry already exist, genError is returned. Binary format: 4 bytes : confIfAddr1 4 bytes : confIfMask1 4 bytes : confIfAddr2 4 bytes : confIfMask2 4 bytes : confIfAddr3 4 bytes : confIfMask3 4 bytes : confIfAddr4 4 bytes : confIfMask4 1 bytes : confIfRouteProto 1 bytes : confIfTrigRip 1 bytes : confIfRipMetric 1 bytes : confIfRip2AuthType 16 bytes : confIfRip2AuthKey 1 bytes : confIfBootpReqForw 1 bytes : confIfProxyArp 1 bytes : confIfFiltering 1 bytes : confIfRxDefAction 1 bytes : confIfTxDefAction 1 bytes : confIfRxDefLogging 1 bytes : confIfTxDefLogging
INT confIfDeleteObj	1.3.6.1.4.1.208.42.1.1.1.19	INTEGER	read-write	Delete an existing table entry
filterTable	1.3.6.1.4.1.208.42.1.2		not-accessible	The table contains IP filter configuration information.
filterEntry	1.3.6.1.4.1.208.42.1.2.1		not-accessible	Configuration information for the IP filter.
INT filterIfIndex	1.3.6.1.4.1.208.42.1.2.1.1	INTEGER	read-only	The ifIndex of the IP link on which the filter is used.
INT filterDirIndex	1.3.6.1.4.1.208.42.1.2.1.2	INTEGER	read-only	Indicates whether the filter is an Rx or Tx filter.
INT filterIndex	1.3.6.1.4.1.208.42.1.2.1.3	INTEGER	read-only	Index in the Rx or Tx filter list for the link.
INT filterAction	1.3.6.1.4.1.208.42.1.2.1.4	INTEGER	read-write	The action to be taken when a packet matches the filter. Disabled filters are ignored.
INT filterLogging	1.3.6.1.4.1.208.42.1.2.1.5	INTEGER	read-write	Indicates whether packets matching the filter must be logged.
INT filterProtocol	1.3.6.1.4.1.208.42.1.2.1.6	INTEGER	read-write	Indicates whether the filter matches all protocols, a user defined protocol or a known protocol.
INT filterProtocolValue	1.3.6.1.4.1.208.42.1.2.1.7	INTEGER	read-write	The protocol field in the IP header of the packet.
INT filterTcpFlags	1.3.6.1.4.1.208.42.1.2.1.8	INTEGER	read-write	Indicates whether the filter matches all TCP packets or only TCP packets with the ACK flag set. When the ACK flag is set, the packet belongs to an established TCP connection.
INT filterSrcAddrType	1.3.6.1.4.1.208.42.1.2.1.9	INTEGER	read-write	Indicates whether the filter matches all source addresses, addresses on a specific network or a specific host address.
IP filterSrcAddr	1.3.6.1.4.1.208.42.1.2.1.10	IpAddress	read-write	Indicates the network or host address which the source address must match.
IP filterSrcMask	1.3.6.1.4.1.208.42.1.2.1.11	IpAddress	read-write	The subnet mask of the network which the source address must match.
INT filterSrcPort	1.3.6.1.4.1.208.42.1.2.1.12	INTEGER	read-write	Indicates whether the filter matches all or a specific UDP/TCP source port.
INT filterSrcPortValue	1.3.6.1.4.1.208.42.1.2.1.13	INTEGER	read-write	The UDP/TCP source port of the filter.
INT filterSrcPortOper	1.3.6.1.4.1.208.42.1.2.1.14	INTEGER	read-write	The source port operator indicates whether UDP/TCP source port values equal to, not equal to, greater than or less than the filter source port match the filter.
INT filterDestAddrType	1.3.6.1.4.1.208.42.1.2.1.15	INTEGER	read-write	Indicates whether the filter matches all destination addresses, addresses on a specific network or a specific host address.
IP filterDestAddr	1.3.6.1.4.1.208.42.1.2.1.16	IpAddress	read-write	Indicates the network or host address which the destination address must match.
IP filterDestMask	1.3.6.1.4.1.208.42.1.2.1.17	IpAddress	read-write	The subnet mask of the network which the destination address must match.
INT filterDestPort	1.3.6.1.4.1.208.42.1.2.1.18	INTEGER	read-write	Indicates whether the filter matches all or a specific UDP/TCP destination port.
INT filterDestPortValue	1.3.6.1.4.1.208.42.1.2.1.19	INTEGER	read-write	The UDP/TCP destination port of the filter.
INT filterDestPortOper	1.3.6.1.4.1.208.42.1.2.1.20	INTEGER	read-write	The destination port operator indicates whether UDP/TCP destination port values equal to, not equal to, greater than or less than the filter destination port match the filter.
CTR filterHits	1.3.6.1.4.1.208.42.1.2.1.21	Counter	read-only	The number of packets matching the filter.
natTable	1.3.6.1.4.1.208.42.1.3		not-accessible	The table contains NAT information.
natEntry	1.3.6.1.4.1.208.42.1.3.1		not-accessible	Information for the NAT entry.
INT natIfIndex	1.3.6.1.4.1.208.42.1.3.1.1	INTEGER	read-only	The ifIndex of the IP link on which the NAT entry is used.
INT natIndex	1.3.6.1.4.1.208.42.1.3.1.2	INTEGER	read-only	Internal NAT index.
IP natIntAddr	1.3.6.1.4.1.208.42.1.3.1.3	IpAddress	read-write	The Internal IP Address of the NAT entry.
IP natIntMask	1.3.6.1.4.1.208.42.1.3.1.4	IpAddress	read-write	The Internal Mask of the NAT entry.
IP natExtAddr	1.3.6.1.4.1.208.42.1.3.1.5	IpAddress	read-write	The External IP Address of the NAT entry.
IP natExtMask	1.3.6.1.4.1.208.42.1.3.1.6	IpAddress	read-write	The External Mask of the NAT entry.
INT natType	1.3.6.1.4.1.208.42.1.3.1.7	INTEGER	read-write	Indicates whether the NAT entry is static or dynamic.
INT natAuto	1.3.6.1.4.1.208.42.1.3.1.8	INTEGER	read-only	Indicates whether the NAT entry has been automatically inserted.
INT natTime	1.3.6.1.4.1.208.42.1.3.1.9	INTEGER	read-only	The time left for dynamic NAT entries.
statRoutTable	1.3.6.1.4.1.208.42.1.4		not-accessible	The table contains static route information.
statRoutEntry	1.3.6.1.4.1.208.42.1.4.1		not-accessible	Information for the static route entry.
INT statRoutIfIndex	1.3.6.1.4.1.208.42.1.4.1.1	INTEGER	read-write	The ifIndex of the IP link on which the static route is used.
IP statRoutNetwork	1.3.6.1.4.1.208.42.1.4.1.2	IpAddress	read-write	IP address of network.
IP statRoutMask	1.3.6.1.4.1.208.42.1.4.1.3	IpAddress	read-write	Subnet mask of network
IP statRoutNextHop	1.3.6.1.4.1.208.42.1.4.1.4	IpAddress	read-write	Next hop router (LAN only)
INT statRoutMetric	1.3.6.1.4.1.208.42.1.4.1.5	INTEGER	read-write	Metric to network
OCT statRoutCreateObj	1.3.6.1.4.1.208.42.1.4.1.6	OCTET STRING	read-write	Create a non existing table entry. If the entry already exist, genError is returned. Binary format: 4 bytes : statRoutMask 4 bytes : statRoutNextHop 4 bytes : statRoutMetric
INT statRoutDeleteObj	1.3.6.1.4.1.208.42.1.4.1.7	INTEGER	read-write	Delete an existing table entry
stat	1.3.6.1.4.1.208.42.2
statIfTable	1.3.6.1.4.1.208.42.2.1		not-accessible	The table contains statistic information for each IP link.
statIfEntry	1.3.6.1.4.1.208.42.2.1.1		not-accessible	Statistic information for the IP link.
INT statIfIndex	1.3.6.1.4.1.208.42.2.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
INT statIfType	1.3.6.1.4.1.208.42.2.1.1.2	INTEGER	read-only	The type of the network (LAN or WAN) to which the IP link is connected.
INT statIfState	1.3.6.1.4.1.208.42.2.1.1.3	INTEGER	read-only	The actual state of the IP link. The link layer informs the IP link of link state changes.
INT statIfMTU	1.3.6.1.4.1.208.42.2.1.1.4	INTEGER	read-only	The maximum transmit unit of the IP link. IP packets larger than the MTU will be fragmented.
CTR statIfRxDefHits	1.3.6.1.4.1.208.42.2.1.1.5	Counter	read-only	The number of packets that did not match any of the Rx Filters for the link.
CTR statIfTxDefHits	1.3.6.1.4.1.208.42.2.1.1.6	Counter	read-only	The number of packets that did not match any of the Tx Filters for the link.
arp	1.3.6.1.4.1.208.42.3
arpIfTable	1.3.6.1.4.1.208.42.3.1		not-accessible	The table contains ARP information for each IP link.
arpIfEntry	1.3.6.1.4.1.208.42.3.1.1		not-accessible	ARP information for the IP link.
INT arpIfIndex	1.3.6.1.4.1.208.42.3.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
CTR arpIfInReq	1.3.6.1.4.1.208.42.3.1.1.2	Counter	read-only	The number of ARP requests received on the link.
CTR arpIfOutRep	1.3.6.1.4.1.208.42.3.1.1.3	Counter	read-only	The number of ARP replies sent on the link.
CTR arpIfOutReq	1.3.6.1.4.1.208.42.3.1.1.4	Counter	read-only	The number of ARP requests sent on the link.
CTR arpIfInRep	1.3.6.1.4.1.208.42.3.1.1.5	Counter	read-only	The number of ARP replies received on the link.
CTR arpIfInHdrErrors	1.3.6.1.4.1.208.42.3.1.1.6	Counter	read-only	The number of ARP packets received on the link which were discarded because of ARP header errors.
CTR arpInReq	1.3.6.1.4.1.208.42.3.2	Counter	read-only	The total number of ARP requests received.
CTR arpOutRep	1.3.6.1.4.1.208.42.3.3	Counter	read-only	The total number of ARP replies sent.
CTR arpOutReq	1.3.6.1.4.1.208.42.3.4	Counter	read-only	The total number of ARP requests sent.
CTR arpInRep	1.3.6.1.4.1.208.42.3.5	Counter	read-only	The total number of ARP replies received.
CTR arpInHdrErrors	1.3.6.1.4.1.208.42.3.6	Counter	read-only	The total number of received ARP packets which were discarded because of ARP header errors.
ip	1.3.6.1.4.1.208.42.4
ipIfTable	1.3.6.1.4.1.208.42.4.1		not-accessible	The table contains statistic information for each IP link.
ipIfEntry	1.3.6.1.4.1.208.42.4.1.1		not-accessible	IP information for the IP link.
INT ipIfIndex	1.3.6.1.4.1.208.42.4.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
CTR ipIfInReceives	1.3.6.1.4.1.208.42.4.1.1.2	Counter	read-only	The number of IP packets received on the link.
CTR ipIfInHdrErrors	1.3.6.1.4.1.208.42.4.1.1.3	Counter	read-only	The number of IP packets received on the link which were discarded because of IP header errors.
CTR ipIfInAddrErrors	1.3.6.1.4.1.208.42.4.1.1.4	Counter	read-only	The number of IP packets received on the link which were discarded because of IP source or destination address errors.
CTR ipIfInDiscards	1.3.6.1.4.1.208.42.4.1.1.5	Counter	read-only	The number of IP packets received on the link which were discarded because of lack of buffer space.
CTR ipIfForwDatagrams	1.3.6.1.4.1.208.42.4.1.1.6	Counter	read-only	The number of IP packets forwarded on the link.
CTR ipIfOutRequests	1.3.6.1.4.1.208.42.4.1.1.7	Counter	read-only	The number of IP packets sent by the router itself.
CTR ipIfOutDiscards	1.3.6.1.4.1.208.42.4.1.1.8	Counter	read-only	The number of IP packets which should have been sent on the link, but were discarded because of lack of buffer space or failed ARP requests.
icmp	1.3.6.1.4.1.208.42.5
icmpIfTable	1.3.6.1.4.1.208.42.5.1		not-accessible	The table contains ICMP information for each IP link.
icmpIfEntry	1.3.6.1.4.1.208.42.5.1.1		not-accessible	ICMP information for the IP link.
INT icmpIfIndex	1.3.6.1.4.1.208.42.5.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
CTR icmpIfInMsgs	1.3.6.1.4.1.208.42.5.1.1.2	Counter	read-only	The number of ICMP messages to the router received on the link.
CTR icmpIfInErrors	1.3.6.1.4.1.208.42.5.1.1.3	Counter	read-only	The number of ICMP messages to the router received on the link which were discarded because of ICMP header errors.
CTR icmpIfInEchos	1.3.6.1.4.1.208.42.5.1.1.4	Counter	read-only	The number of ICMP echo requests received on the link.
CTR icmpIfInEchoReps	1.3.6.1.4.1.208.42.5.1.1.5	Counter	read-only	The number of ICMP echo replies received on the link.
CTR icmpIfOutMsgs	1.3.6.1.4.1.208.42.5.1.1.6	Counter	read-only	The number of ICMP messages sent on the link.
CTR icmpIfOutEchos	1.3.6.1.4.1.208.42.5.1.1.7	Counter	read-only	The number of ICMP echo requests sent on the link.
CTR icmpIfOutEchoReps	1.3.6.1.4.1.208.42.5.1.1.8	Counter	read-only	The number of ICMP echo replies sent on the link.
CTR icmpInRouterAdvs	1.3.6.1.4.1.208.42.5.2	Counter	read-only	The total number of received ICMP Router Advertisements.
CTR icmpInRouterSols	1.3.6.1.4.1.208.42.5.3	Counter	read-only	The total number of received ICMP Router Solicitations.
CTR icmpOutRouterAdvs	1.3.6.1.4.1.208.42.5.4	Counter	read-only	The total number of sent ICMP Router Advertisements.
CTR icmpOutRouterSols	1.3.6.1.4.1.208.42.5.5	Counter	read-only	The total number of sent ICMP Router Solicitations.
rip	1.3.6.1.4.1.208.42.6
ripIfTable	1.3.6.1.4.1.208.42.6.1		not-accessible	The table contains RIP information for each IP link.
ripIfEntry	1.3.6.1.4.1.208.42.6.1.1		not-accessible	RIP information for the IP link.
INT ripIfIndex	1.3.6.1.4.1.208.42.6.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
CTR ripIfInReceives	1.3.6.1.4.1.208.42.6.1.1.2	Counter	read-only	The number of RIP packets received on the link.
CTR ripIfInHdrErrors	1.3.6.1.4.1.208.42.6.1.1.3	Counter	read-only	The number of RIP packets received on the link which were discarded because of RIP header errors.
CTR ripIfInBadSrcAddrs	1.3.6.1.4.1.208.42.6.1.1.4	Counter	read-only	The number of RIP packets received on the link which were discarded because of source address errors. This may indicate an IP address configuration error on the link or the link of the router from which the RIP packet was received. The error may also occur if the link is connected to a physical network with multiple logical IP networks. In the latter case a source address error is not an indication of an IP address configuration error.
CTR ripIfInBadVers	1.3.6.1.4.1.208.42.6.1.1.5	Counter	read-only	The number of RIP packets received on the link which were discarded because of RIP version errors. This indicates a RIP configuration error on the link or the link of the router from which the RIP packet was received. The error occurs when receiving a RIP packet with a version different from the version configured on the link. The error also occurs if a RIP packet is received and the link is configured not to use RIP.
CTR ripIfInAuthFails	1.3.6.1.4.1.208.42.6.1.1.6	Counter	read-only	The number of RIP packets received on the link which were discarded because of RIP-2 authentication failures.
CTR ripIfInUnknComs	1.3.6.1.4.1.208.42.6.1.1.7	Counter	read-only	The number of RIP packets received on the link which were discarded because of an unknown command type. This may indicate that the link is not configured to use Triggered RIP and the remote router is using Triggered RIP.
CTR ripIfOutSent	1.3.6.1.4.1.208.42.6.1.1.8	Counter	read-only	The number of RIP packets sent on the link.
CTR ripIfOutDiscards	1.3.6.1.4.1.208.42.6.1.1.9	Counter	read-only	The number of RIP packets discarded because of lack of buffer space.
CTR ripInReceives	1.3.6.1.4.1.208.42.6.2	Counter	read-only	The total number of received RIP packets.
CTR ripInHdrErrors	1.3.6.1.4.1.208.42.6.3	Counter	read-only	The total number of received RIP packets discarded because of RIP header errors.
CTR ripInBadSrcAddrs	1.3.6.1.4.1.208.42.6.4	Counter	read-only	The total number of received RIP packets discarded because of source address errors.
CTR ripInBadVers	1.3.6.1.4.1.208.42.6.5	Counter	read-only	The total number of received RIP packets discarded because of RIP version errors.
CTR ripInAuthFails	1.3.6.1.4.1.208.42.6.6	Counter	read-only	The total number of RIP-2 authentication failures.
CTR ripInUnknComs	1.3.6.1.4.1.208.42.6.7	Counter	read-only	The total number of received RIP packets discarded because of an unknown command type.
CTR ripOutSent	1.3.6.1.4.1.208.42.6.8	Counter	read-only	The total number of RIP packets sent by the router.
CTR ripOutDiscards	1.3.6.1.4.1.208.42.6.9	Counter	read-only	The total number of RIP packets discarded because of lack of buffer space.
bootp	1.3.6.1.4.1.208.42.7
bootpIfTable	1.3.6.1.4.1.208.42.7.1		not-accessible	The table contains BOOTP information for each IP link.
bootpIfEntry	1.3.6.1.4.1.208.42.7.1.1		not-accessible	BOOTP information for the IP link.
INT bootpIfIndex	1.3.6.1.4.1.208.42.7.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
CTR bootpIfInRequests	1.3.6.1.4.1.208.42.7.1.1.2	Counter	read-only	The number of BOOTP requests received on the link.
CTR bootpIfInReplies	1.3.6.1.4.1.208.42.7.1.1.3	Counter	read-only	The number of BOOTP replies received on the link.
CTR bootpIfInErrors	1.3.6.1.4.1.208.42.7.1.1.4	Counter	read-only	The number of BOOTP packets received on the link which were discarded because of header errors.
CTR bootpIfInDiscards	1.3.6.1.4.1.208.42.7.1.1.5	Counter	read-only	The number of BOOTP requests received on the link which were discarded. This is done in the following situations: - The maximum value of the BOOTP hop count is exceeded. - More than 3 BOOTP packets are received per second. - The router does not have a route back to the assisting router using the receving link.
CTR bootpIfOutRequests	1.3.6.1.4.1.208.42.7.1.1.6	Counter	read-only	The number of BOOTP requests sent on the link.
CTR bootpIfOutReplies	1.3.6.1.4.1.208.42.7.1.1.7	Counter	read-only	The number of BOOTP replies sent on the link.
CTR bootpIfOutDiscards	1.3.6.1.4.1.208.42.7.1.1.8	Counter	read-only	The number of BOOTP requests discarded because of lack of buffer space.
CTR bootpInRequests	1.3.6.1.4.1.208.42.7.2	Counter	read-only	The total number of received BOOTP requests.
CTR bootpInReplies	1.3.6.1.4.1.208.42.7.3	Counter	read-only	The total number of received BOOTP replies.
CTR bootpInErrors	1.3.6.1.4.1.208.42.7.4	Counter	read-only	The total number of received BOOTP packets discarded because of header errors.
CTR bootpInDiscards	1.3.6.1.4.1.208.42.7.5	Counter	read-only	The total number of received BOOTP requests discarded. This is done in the following situations: - The maximum value of the BOOTP hop count is exceeded. - More than 3 BOOTP packets are received per second. - The router does not have a route back to the assisting router using the receiving link.
CTR bootpOutRequests	1.3.6.1.4.1.208.42.7.6	Counter	read-only	The total number of BOOTP requests sent by the router.
CTR bootpOutReplies	1.3.6.1.4.1.208.42.7.7	Counter	read-only	The total number of BOOTP replies sent to BOOTP clients.
CTR bootpOutDiscards	1.3.6.1.4.1.208.42.7.8	Counter	read-only	The total number of BOOTP requests discarded because of lack of buffer space.
INT bootpMaxHops	1.3.6.1.4.1.208.42.7.9	INTEGER	read-write	The maximum allowed value of the hop count in received BOOTP requests.
octetcounters	1.3.6.1.4.1.208.42.8
octetIfTable	1.3.6.1.4.1.208.42.8.1		not-accessible	The table contains octet counters for each IP link.
octetIfEntry	1.3.6.1.4.1.208.42.8.1.1		not-accessible	Octet counter information for the IP link.
INT octetIfIndex	1.3.6.1.4.1.208.42.8.1.1.1	INTEGER	read-only	The ifIndex of the IP link.
CTR octetIfInTotal	1.3.6.1.4.1.208.42.8.1.1.2	Counter	read-only	The total number of octets received on the IP link.
CTR octetIfOutTotal	1.3.6.1.4.1.208.42.8.1.1.3	Counter	read-only	The total number of octets sent on the IP link.
CTR octetIfInOther	1.3.6.1.4.1.208.42.8.1.1.4	Counter	read-only	The number of octets received on the IP link which were not classified as a specific protocol.
CTR octetIfOutOther	1.3.6.1.4.1.208.42.8.1.1.5	Counter	read-only	The number of octets sent on the IP link which were not classified as a specific protocol.
CTR octetIfInFtp	1.3.6.1.4.1.208.42.8.1.1.6	Counter	read-only	The number of FTP octets received on the IP link.
CTR octetIfOutFtp	1.3.6.1.4.1.208.42.8.1.1.7	Counter	read-only	The number of FTP octets sent on the IP link.
CTR octetIfInTelnet	1.3.6.1.4.1.208.42.8.1.1.8	Counter	read-only	The number of Telnet octets received on the IP link.
CTR octetIfOutTelnet	1.3.6.1.4.1.208.42.8.1.1.9	Counter	read-only	The number of Telnet octets sent on the IP link.
CTR octetIfInSmtp	1.3.6.1.4.1.208.42.8.1.1.10	Counter	read-only	The number of SMTP octets received on the IP link.
CTR octetIfOutSmtp	1.3.6.1.4.1.208.42.8.1.1.11	Counter	read-only	The number of SMTP octets sent on the IP link.
CTR octetIfInDns	1.3.6.1.4.1.208.42.8.1.1.12	Counter	read-only	The number of DNS octets received on the IP link.
CTR octetIfOutDns	1.3.6.1.4.1.208.42.8.1.1.13	Counter	read-only	The number of DNS octets sent on the IP link.
CTR octetIfInBootp	1.3.6.1.4.1.208.42.8.1.1.14	Counter	read-only	The number of BOOTP octets received on the IP link.
CTR octetIfOutBootp	1.3.6.1.4.1.208.42.8.1.1.15	Counter	read-only	The number of BOOTP octets sent on the IP link.
CTR octetIfInHttp	1.3.6.1.4.1.208.42.8.1.1.16	Counter	read-only	The number of HTTP octets received on the IP link.
CTR octetIfOutHttp	1.3.6.1.4.1.208.42.8.1.1.17	Counter	read-only	The number of HTTP octets sent on the IP link.
CTR octetIfInSnmp	1.3.6.1.4.1.208.42.8.1.1.18	Counter	read-only	The number of SNMP octets received on the IP link.
CTR octetIfOutSnmp	1.3.6.1.4.1.208.42.8.1.1.19	Counter	read-only	The number of SNMP octets sent on the IP link.
CTR octetIfInRip	1.3.6.1.4.1.208.42.8.1.1.20	Counter	read-only	The number of RIP octets received on the IP link.
CTR octetIfOutRip	1.3.6.1.4.1.208.42.8.1.1.21	Counter	read-only	The number of RIP octets sent on the IP link.
CTR octetIfInTunnel	1.3.6.1.4.1.208.42.8.1.1.22	Counter	read-only	The number of Tunnel octets received on the IP link.
CTR octetIfOutTunnel	1.3.6.1.4.1.208.42.8.1.1.23	Counter	read-only	The number of Tunnel octets sent on the IP link.

RFC description

Management information for systems functioning as IP routers, including configuration of IP interfaces, routing protocols, and DHCP relay services.

Start monitoring Securicor Arisoft WAN routers (per-link IP configuration/protocol traffic statistics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SCA-IPROUTER-MIB

What Is SCA-IPROUTER-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description