RND-MIB

All MIBs › RND-MIB

Category: Routing, SMI / Registration

Description: Defines the base OID tree and common management objects for RAD Network Devices equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RND-MIB?

RND-MIB is a large vendor-specific MIB from RAD Data Communications (RAD Network Devices) that defines the base OID tree, rnd (enterprises.89), for RAD's Vgate/OpenGate family of modular multiprotocol routers and bridges, along with a broad set of common management groups spanning far beyond a simple root — bridging (rndBridgeAlarm), interfaces (rndInterface), IPX routing and SAP/RIP (rndIPX, ripsap, ipxCircTable, ipxDestTable, ipxServTable), IP-layer extensions (ipSpec covering rsIpAddrTable, icmpSpec, rip2Spec, arpSpec, ipRedundancy, ipRouteLeaking, ipRipFilter), Facility for Access Control and Security (rndFACS), VLAN definitions (virtualLan), router-server configuration and tuning (rsConf, rsTunning, rsMaxEntriesTuning), and BootP configuration (rndBootP). Its tables are typically indexed by circuit/interface identifiers and expose both configuration objects (filters, thresholds, redundancy peers) and status/counter objects (e.g., rndFACSTable access-control entries, ipRedundRoutersTable peer status, eventMessageTable logged events). Because this module anchors the entire RAD device OID hierarchy, virtually every other RAD product-specific MIB depends on it, and it is deployed on the full range of RAD Vgate, OpenGate, and related multiprotocol router/bridge hardware. Administrators can download the RND-MIB file to load its extensive OID tree into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RND-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

RAD Data Communications Vgate/OpenGate modular routers and bridges
RAD Data Communications network access devices

Monitoring Examples

An operator polls ipRedundRoutersTable to confirm redundant router peers are visible and healthy, and checks rndFACSTable for unexpected access-control entries; a redundancy peer that drops out of the table, or an unexplained new FACS entry, would indicate a failover event or a security configuration change worth investigating.

What Can Be Monitored

IP redundancy peer/router table
IPX routing, SAP, and RIP tables
Facility for Access Control and Security (FACS) entries
VLAN and route-leaking configuration
interface/circuit configuration tables
event/alarm message log table

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
enterprises

From RFC1213-MIB

DisplayString
PhysAddress
ipAddrEntry

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF abortTftp	1.3.6.1.4.1.89.0.13			This trap indicates that in the device aborted a TFTP session with the management station. variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
arpSpec	1.3.6.1.4.1.89.26.4
NTF autoConfigurationCompleted	1.3.6.1.4.1.89.0.50			This trap indicates that auto comfiguration completetd succssefully. The bound variable rndErrorDesc, rndErrorSeverity(== info )
NTF endTftp	1.3.6.1.4.1.89.0.12			This trap indicates that in the device finished a TFTP transaction with the management station. variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
NTF errorsDuringInit	1.3.6.1.4.1.89.0.61
STR eventDesc	1.3.6.1.4.1.89.29.6.1.2	DisplayString	read-only	The event discription, this text will include time and severity.
eventMessageEntry	1.3.6.1.4.1.89.29.6.1		not-accessible	The row definition for this table.
eventMessageTable	1.3.6.1.4.1.89.29.6		not-accessible	The Event Message table of the agent
INT eventNum	1.3.6.1.4.1.89.29.6.1.1	INTEGER	read-only	The event number,the index of this table.
NTF facsAccessVoilation	1.3.6.1.4.1.89.0.49			This trap indicates that message that fits FACS statenebt with operation blockAndReport was forward to the interface.The bound variable rndErrorDesc, rndErrorSeverity(== info ) and interface Number.
NTF forwardingTabOverflow	1.3.6.1.4.1.89.0.51			This trap indicates that an overflow condition has occurred in the layer II Forward Table. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
genGroup	1.3.6.1.4.1.89.2.11
STR genGroupConfigurationSymbol	1.3.6.1.4.1.89.2.11.2	DisplayString	read-only	Defines the Configuration Symbol attached to any hardware module manufactured by LANNET. One single character A..Z defines the CS version.
INT genGroupHWStatus	1.3.6.1.4.1.89.2.11.3	INTEGER	read-only	This attribute describes the status of the group hardware as detected by the sensors software.
STR genGroupHWVersion	1.3.6.1.4.1.89.2.11.1	DisplayString	read-only	Defines the HW version of the product.
icmpSpec	1.3.6.1.4.1.89.26.2
INT ipLeakExtDirectToOspf	1.3.6.1.4.1.89.26.7.5	INTEGER	read-write	This parameter controls leaking (redistribution) into OSPF of direct routes external to OSPF, i.e. routes to local network corresponding to IP interfaces on which OSPF is disabled. When enabled, all such direct routes are advertised into OSPF as external routes.
INT ipLeakOspfToRip	1.3.6.1.4.1.89.26.7.3	INTEGER	read-write	This parameter controls leaking (redistribution) of routes from OSPF to RIP. If enabled, all routes learned via OSPF are advertised into RIP.
INT ipLeakRipToOspf	1.3.6.1.4.1.89.26.7.4	INTEGER	read-write	This parameter controls leaking (redistribution) of routes from RIP to OSPF. If enabled, all routes learned via RIP are advertised into OSPF as external routes.
INT ipLeakStaticToOspf	1.3.6.1.4.1.89.26.7.2	INTEGER	read-write	This parameter controls leaking (redistribution) of static routes into OSPF. When enabled, all routes inserted to the IP routing table via SNMP are advertised into OSPF as external routes.
INT ipLeakStaticToRip	1.3.6.1.4.1.89.26.7.1	INTEGER	read-write	This parameter controls leaking (redistribution) of static routes to RIP. When enabled, all routes inserted to the IP routing table via SNMP are advertised into RIP.
INT ipRedundAdminStatus	1.3.6.1.4.1.89.26.6.1	INTEGER	read-write	This parameter controle the IP Redundancy in the device. In case the the parameter in Enable and second router down. all the traffic hendle by this element.
ipRedundancy	1.3.6.1.4.1.89.26.6
INT ipRedundOperStatus	1.3.6.1.4.1.89.26.6.2	INTEGER	read-only	obsolete
ipRedundRoutersEntry	1.3.6.1.4.1.89.26.6.3.1		not-accessible	The row definition for this table.
IP ipRedundRoutersIfAddr	1.3.6.1.4.1.89.26.6.3.1.1	IpAddress	read-only	The Ip address of the IP interface on which the redundancy feature is operational.
IP ipRedundRoutersMainRouterAddr	1.3.6.1.4.1.89.26.6.3.1.2	IpAddress	read-only	The Ip address of the polled main router.
INT ipRedundRoutersOperStatus	1.3.6.1.4.1.89.26.6.3.1.3	INTEGER	read-only	If active, the main router is considered inoperational and the IP interface operates as its backup.
INT ipRedundRoutersPollInterval	1.3.6.1.4.1.89.26.6.3.1.4	INTEGER	read-write	Polling interval for this router (in seconds). If 0 the router is not polled.
INT ipRedundRoutersStatus	1.3.6.1.4.1.89.26.6.3.1.6	INTEGER	read-write	Entry status
ipRedundRoutersTable	1.3.6.1.4.1.89.26.6.3		not-accessible	List of IP addresses backed up by this router.
INT ipRedundRoutersTimeout	1.3.6.1.4.1.89.26.6.3.1.5	INTEGER	read-write	Interval in seconds during which the backed-up router must signal. If it does not signal, it is considered inoperational and the IP interface starts operating as backup.
ipRipFilter	1.3.6.1.4.1.89.26.8
ipRouteLeaking	1.3.6.1.4.1.89.26.7
ipSpec	1.3.6.1.4.1.89.26
ipxBasicSysEntry	1.3.6.1.4.1.89.12.4.1.1		not-accessible	Each entry corresponds to one instance of IPX running on the system.
INT ipxBasicSysExistState	1.3.6.1.4.1.89.12.4.1.1.2	INTEGER	read-write	The validity of this entry in the IPX system table. Setting this field to off indicates that this entry may be deleted from the system table at the IPX implementation's discretion.
CTR ipxBasicSysInDelivers	1.3.6.1.4.1.89.12.4.1.1.7	Counter	read-only	The total number of IPX packets delivered locally, including packets from local applications.
CTR ipxBasicSysInDiscards	1.3.6.1.4.1.89.12.4.1.1.6	Counter	read-only	The number of IPX packets received but discarded due to reasons other than those accounted for by ipxBasicSysInHdrErrors, ipxBasicSysInUnknownSockets, ipxAdvSysInDiscards, and ipxAdvSysInCompressDiscards.
CTR ipxBasicSysInHdrErrors	1.3.6.1.4.1.89.12.4.1.1.4	Counter	read-only	The number of IPX packets discarded due to errors in their headers, including any IPX packet with a size less than the minimum of 30 bytes.
CTR ipxBasicSysInReceives	1.3.6.1.4.1.89.12.4.1.1.3	Counter	read-only	The total number of IPX packets received, including those received in error.
INT ipxBasicSysInstance	1.3.6.1.4.1.89.12.4.1.1.1	INTEGER	read-write	The unique identifier of the instance of IPX to which this row corresponds. This value may be written only when creating a new entry in the table.
CTR ipxBasicSysInUnknownSockets	1.3.6.1.4.1.89.12.4.1.1.5	Counter	read-only	The number of IPX packets discarded because the destination socket was not open.
CTR ipxBasicSysNoRoutes	1.3.6.1.4.1.89.12.4.1.1.8	Counter	read-only	The number of times no route to a destination was found.
CTR ipxBasicSysOutDiscards	1.3.6.1.4.1.89.12.4.1.1.11	Counter	read-only	The number of outgoing IPX packets discarded due to reasons other than those accounted for in ipxBasicSysOutMalformedRequests, ipxAdvSysOutFiltered, and ipxAdvSysOutCompressDiscards.
CTR ipxBasicSysOutMalformedRequests	1.3.6.1.4.1.89.12.4.1.1.10	Counter	read-only	The number of IPX packets supplied locally that contained errors in their structure.
CTR ipxBasicSysOutPackets	1.3.6.1.4.1.89.12.4.1.1.12	Counter	read-only	The total number of IPX packets transmitted.
CTR ipxBasicSysOutRequests	1.3.6.1.4.1.89.12.4.1.1.9	Counter	read-only	The number of IPX packets supplied locally for transmission, not including any packets counted in ipxAdvForwPackets.
ipxBasicSysTable	1.3.6.1.4.1.89.12.4.1		not-accessible	The IPX System table - basic information.
INT ipxCircEncaps	1.3.6.1.4.1.89.12.5.1.1.8	INTEGER	read-write	The encapsulation method associated with this interface.
ipxCircEntry	1.3.6.1.4.1.89.12.5.1.1		not-accessible	Each entry corresponds to one circuit known to the system.
INT ipxCircExistState	1.3.6.1.4.1.89.12.5.1.1.3	INTEGER	read-write	The validity of this circuit entry. A circuit with this value set to off may be deleted from the table at the IPX implementation's discretion.
INT ipxCircIfIndex	1.3.6.1.4.1.89.12.5.1.1.5	INTEGER	read-write	The value of ifIndex for the interface used by this circuit. This value may be written only when creating a new entry in the table.
INT ipxCircIndex	1.3.6.1.4.1.89.12.5.1.1.2	INTEGER	read-write	The identifier of this circuit, unique within the instance of IPX. This value may be written only when creating a new entry in the table.
INT ipxCircNetbiosDeliver	1.3.6.1.4.1.89.12.5.1.1.9	INTEGER	read-write	Deliver NetBios All Networks Broadcast Packets
NET ipxCircNetNumber	1.3.6.1.4.1.89.12.5.1.1.6	NetNumber	read-write	The IPX network number of this circuit. This value may be written only when creating a new entry in the table.
INT ipxCircOperState	1.3.6.1.4.1.89.12.5.1.1.4	INTEGER	read-only	The operational state of the circuit.
INT ipxCircSysInstance	1.3.6.1.4.1.89.12.5.1.1.1	INTEGER	read-write	The unique identifier of the instance of IPX to which this entry corresponds. This value may be written only when creating a new entry in the table.
ipxCircTable	1.3.6.1.4.1.89.12.5.1		not-accessible	The Circuit table.
INT ipxCircTimeToNet	1.3.6.1.4.1.89.12.5.1.1.7	INTEGER	read-write	The time to net value associated with this interface, in term of 1/18ths of a second.
ipxCircuit	1.3.6.1.4.1.89.12.5
ipxDestEntry	1.3.6.1.4.1.89.12.6.1.1		not-accessible	Each entry corresponds to one destination.
INT ipxDestExistState	1.3.6.1.4.1.89.12.6.1.1.9	INTEGER	read-write	The validity of this entry. An entry with this value set to off may be deleted from the table at the IPX implementation's discretion.
INT ipxDestHopCount	1.3.6.1.4.1.89.12.6.1.1.6	INTEGER	read-write	The number of hops necessary to reach the destination.
NET ipxDestNetNum	1.3.6.1.4.1.89.12.6.1.1.2	NetNumber	read-only	The IPX network number of the destination.
INT ipxDestNextHopCircIndex	1.3.6.1.4.1.89.12.6.1.1.3	INTEGER	read-write	The unique identifier of the circuit used to reach the next hop.
NET ipxDestNextHopNetNum	1.3.6.1.4.1.89.12.6.1.1.8	NetNumber	read-write	The IPX network number of the next hop.
PHY ipxDestNextHopNICAddress	1.3.6.1.4.1.89.12.6.1.1.7	PhysAddress	read-write	The NIC address of the next hop.
INT ipxDestProtocol	1.3.6.1.4.1.89.12.6.1.1.4	INTEGER	read-only	The routing protocol from which knowledge of this destination was obtained.
INT ipxDestSysInstance	1.3.6.1.4.1.89.12.6.1.1.1	INTEGER	read-only	The unique identifier of the instance of IPX to which this row corresponds.
ipxDestTable	1.3.6.1.4.1.89.12.6.1		not-accessible	The Destination table contains information about all known destinations.
INT ipxDestTicks	1.3.6.1.4.1.89.12.6.1.1.5	INTEGER	read-write	The delay in ticks to reach this destination.
ipxForwarding	1.3.6.1.4.1.89.12.6
NTF ipxRipTblOverflow	1.3.6.1.4.1.89.0.36			This trap indicates that in an OpenGate IPX RIP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
NTF ipxSapTblOverflow	1.3.6.1.4.1.89.0.37			This trap indicates that in an OpenGate IPX SAP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
ipxServEntry	1.3.6.1.4.1.89.12.7.1.1		not-accessible	Each entry corresponds to one service.
INT ipxServExistState	1.3.6.1.4.1.89.12.7.1.1.9	INTEGER	read-write	The validity of this entry. An entry with this value set to off may be deleted from the table at the IPX implementation's discretion.
INT ipxServHopCount	1.3.6.1.4.1.89.12.7.1.1.8	INTEGER	read-write	The number of hops to the service.
ipxServices	1.3.6.1.4.1.89.12.7
OCT ipxServName	1.3.6.1.4.1.89.12.7.1.1.3	OCTET STRING	read-write	The service name.
NET ipxServNetNum	1.3.6.1.4.1.89.12.7.1.1.5	NetNumber	read-write	The IPX network number portion of the IPX address of the service.
OCT ipxServNode	1.3.6.1.4.1.89.12.7.1.1.6	OCTET STRING	read-write	The node portion of the IPX address of the service.
INT ipxServProtocol	1.3.6.1.4.1.89.12.7.1.1.4	INTEGER	read-only	The protocol from which knowledge of this service was obtained.
OCT ipxServSocket	1.3.6.1.4.1.89.12.7.1.1.7	OCTET STRING	read-write	The socket portion of the IPX address of the service.
INT ipxServSysInstance	1.3.6.1.4.1.89.12.7.1.1.1	INTEGER	read-only	The unique identifier of the instance of IPX to which this entry corresponds.
ipxServTable	1.3.6.1.4.1.89.12.7.1		not-accessible	The table of services, indexed by name and type.
OCT ipxServType	1.3.6.1.4.1.89.12.7.1.1.2	OCTET STRING	read-write	The service type.
ipxSystem	1.3.6.1.4.1.89.12.4
IP lreBoxAgentIP	1.3.6.1.4.1.89.26.10	IpAddress	read-write
INT lreQueSourceSelect	1.3.6.1.4.1.89.29.7.24	INTEGER	read-write
INT lreResetDstMacBit46	1.3.6.1.4.1.89.29.7.23	INTEGER	read-write
INT lreResetDstMacBit47	1.3.6.1.4.1.89.29.7.25	INTEGER	read-write
lreVnResposibilityEntry	1.3.6.1.4.1.89.29.7.17.1		not-accessible	The row definition for this table.
lreVnResposibilityTable	1.3.6.1.4.1.89.29.7.17		not-accessible	The Bridge Responsibility Table
ROW lreVnRespStatus	1.3.6.1.4.1.89.29.7.17.1.2	RowStatus	read-write
INT lreVnRespVn	1.3.6.1.4.1.89.29.7.17.1.1	INTEGER	read-write
CTR reaBrgDiscards	1.3.6.1.4.1.89.29.7.13	Counter	read-only	The number of bridging datagrams have been discarded by the Platform.
INT reaBrgFftEntryNum	1.3.6.1.4.1.89.29.7.12.1.1	INTEGER	read-only
INT reaBrgFftFacsDstIndex	1.3.6.1.4.1.89.29.7.12.1.6	INTEGER	read-only
INT reaBrgFftFacsSrcIndex	1.3.6.1.4.1.89.29.7.12.1.5	INTEGER	read-only
PHY reaBrgFftMacAddr	1.3.6.1.4.1.89.29.7.12.1.2	PhysAddress	read-only
INT reaBrgFftPortNum	1.3.6.1.4.1.89.29.7.12.1.4	INTEGER	read-only
INT reaBrgFftReNum	1.3.6.1.4.1.89.29.7.12.1.3	INTEGER	read-only
CTR reaBrgForwards	1.3.6.1.4.1.89.29.7.14	Counter	read-only	The number of bridging datagrams have been forwarded by the Platform.
INT reaBridgeEnable	1.3.6.1.4.1.89.29.7.6	INTEGER	read-write	The Platform will perform bridging if only if this variable's value is enable.
reaBridgeFftEntry	1.3.6.1.4.1.89.29.7.12.1		not-accessible	The row definition for this table.
reaBridgeFftTable	1.3.6.1.4.1.89.29.7.12		not-accessible	The Bridge Fast Forwarding Table
INT reaBufFree	1.3.6.1.4.1.89.29.7.22	INTEGER	read-only	The number of free buffers.
INT reaFacsEnable	1.3.6.1.4.1.89.29.7.7	INTEGER	read-write	The RS and Platform will perform FASC if only if this variable's value is enable.
INT reaFftHashMaxChain	1.3.6.1.4.1.89.29.7.2	INTEGER	read-write	This variable specifies the maximum length of hash chains in the Fast Forwarding Tables.
OCT reaIpFftApplFlags	1.3.6.1.4.1.89.29.7.15.1.11	OCTET STRING	read-only	A bit mask that defines the applications associated with this entry: __________________________________________ \| Byte 1\|Byte 2 \|Byte 3 \| ....\|Byte 20 \| \|87654321\| \| 87654321\| \|________\|_______________________________\| Byte1 : bit1: Server Dispatcher Client
IP reaIpFftDstIpAddr	1.3.6.1.4.1.89.29.7.15.1.2	IpAddress	read-only
IP reaIpFftDstIpMask	1.3.6.1.4.1.89.29.7.15.1.3	IpAddress	read-only
PHY reaIpFftDstMacAddr	1.3.6.1.4.1.89.29.7.15.1.6	PhysAddress	read-only
reaIpFftEntry	1.3.6.1.4.1.89.29.7.15.1		not-accessible	The row definition for this table.
INT reaIpFftEntryNum	1.3.6.1.4.1.89.29.7.15.1.1	INTEGER	read-only
INT reaIpFftFacsDstIndex	1.3.6.1.4.1.89.29.7.15.1.10	INTEGER	read-only
INT reaIpFftFacsSrcIndex	1.3.6.1.4.1.89.29.7.15.1.9	INTEGER	read-only
INT reaIpFftPortNum	1.3.6.1.4.1.89.29.7.15.1.8	INTEGER	read-only
INT reaIpFftRangeType	1.3.6.1.4.1.89.29.7.15.1.4	INTEGER	read-only
INT reaIpFftReNum	1.3.6.1.4.1.89.29.7.15.1.7	INTEGER	read-only
PHY reaIpFftSrcMacAddr	1.3.6.1.4.1.89.29.7.15.1.5	PhysAddress	read-only
reaIpFftTable	1.3.6.1.4.1.89.29.7.15		not-accessible	The IP Fast Forwarding Table
CTR reaIpForwardDatagrams	1.3.6.1.4.1.89.29.7.8	Counter	read-only	The number of IP datagrams have been forwarded by the Platform.
INT reaIpForwardEnable	1.3.6.1.4.1.89.29.7.4	INTEGER	read-write	The Platform will perform fast IP forwarding if only if this variable's value is enable.
CTR reaIpInDiscards	1.3.6.1.4.1.89.29.7.9	Counter	read-only	The number of IP datagrams have been dicarded by the Platform.
INT reaIpRemoteAgingTime	1.3.6.1.4.1.89.29.7.1	INTEGER	read-write	This variable specifies aging time used by the REA for remote entries in the Ip Fast Forwarding Table.
PHY reaIpxFftDstMacAddr	1.3.6.1.4.1.89.29.7.16.1.5	PhysAddress	read-only
INT reaIpxFftDstNetid	1.3.6.1.4.1.89.29.7.16.1.2	INTEGER	read-only
reaIpxFftEntry	1.3.6.1.4.1.89.29.7.16.1		not-accessible	The row definition for this table.
INT reaIpxFftEntryNum	1.3.6.1.4.1.89.29.7.16.1.1	INTEGER	read-only
INT reaIpxFftFacsDstIndex	1.3.6.1.4.1.89.29.7.16.1.9	INTEGER	read-only
INT reaIpxFftFacsSrcIndex	1.3.6.1.4.1.89.29.7.16.1.8	INTEGER	read-only
INT reaIpxFftPortNum	1.3.6.1.4.1.89.29.7.16.1.7	INTEGER	read-only
INT reaIpxFftRangeType	1.3.6.1.4.1.89.29.7.16.1.3	INTEGER	read-only
INT reaIpxFftReNum	1.3.6.1.4.1.89.29.7.16.1.6	INTEGER	read-only
PHY reaIpxFftSrcMacAddr	1.3.6.1.4.1.89.29.7.16.1.4	PhysAddress	read-only
reaIpxFftTable	1.3.6.1.4.1.89.29.7.16		not-accessible	The IPX Fast Forwarding Table
CTR reaIpxForwardDatagrams	1.3.6.1.4.1.89.29.7.10	Counter	read-only	The number of IPX datagrams have been forwarded by the Platform.
INT reaIpxForwardEnable	1.3.6.1.4.1.89.29.7.5	INTEGER	read-write	The Platform will perform fast IPX forwarding if only if this variable's value is enable.
CTR reaIpxInDiscards	1.3.6.1.4.1.89.29.7.11	Counter	read-only	The number of IP datagrams have been dicarded by the Platform.
INT reaMltcstBitOn	1.3.6.1.4.1.89.29.7.3	INTEGER	read-write
CTR reaRsQueueDiscards	1.3.6.1.4.1.89.29.7.21	Counter	read-only
INT reaSrcAddrValidationEnable	1.3.6.1.4.1.89.29.7.20	INTEGER	read-write	The Platform will verify the source address of incoming IP datagram.
INT reaSrcViolationEnable	1.3.6.1.4.1.89.29.7.18	INTEGER	read-write	The Platform will perform the Source Port Violation Procedure if only if this variable's value is enable.
INT reaSrcViolationTrapEnable	1.3.6.1.4.1.89.29.7.19	INTEGER	read-write	The RS will send the Source Port Violation TRAP messages if only if this variable's value is enable.
reaTunning	1.3.6.1.4.1.89.29.7
NTF resetRequired	1.3.6.1.4.1.89.0.10			This trap indicates that in order to perform the last SET request, a reset operation of the router/bridge is required. This occurs when the layer 2 routing algorithm is changed between SPF and Spanning Tree. The reset can be performed manually or using the variable rndAction.
rip2Spec	1.3.6.1.4.1.89.26.3
INT ripCircAgeMultiplier	1.3.6.1.4.1.89.12.8.2.1.1.5	INTEGER	read-write	The holding multiplier for information received in RIP periodic updates.
ripCircEntry	1.3.6.1.4.1.89.12.8.2.1.1		not-accessible	Each entry corresponds to one circuit known to the system.
INT ripCircIndex	1.3.6.1.4.1.89.12.8.2.1.1.2	INTEGER	read-write	The identifier of this circuit, unique within the instance of RIP. This value corresponds to the circuit identifier found in ipxCircIndex. This value may be written only when creating a new entry in the table.
CTR ripCircInPackets	1.3.6.1.4.1.89.12.8.2.1.1.7	Counter	read-only	The number of RIP packets received on this circuit.
CTR ripCircOutPackets	1.3.6.1.4.1.89.12.8.2.1.1.6	Counter	read-only	The number of RIP packets sent on this circuit.
INT ripCircState	1.3.6.1.4.1.89.12.8.2.1.1.3	INTEGER	read-write	Indicates whether RIP information may be sent/received over this circuit.
INT ripCircSysInstance	1.3.6.1.4.1.89.12.8.2.1.1.1	INTEGER	read-write	The unique identifier of the instance of RIP and IPX (via ipxSysInstance) to which this entry corresponds. This value may be written only when creating a new entry in the table.
ripCircTable	1.3.6.1.4.1.89.12.8.2.1		not-accessible	The RIP Circuit table.
INT ripCircUpdate	1.3.6.1.4.1.89.12.8.2.1.1.4	INTEGER	read-write	The RIP periodic update interval, in seconds.
ripsap	1.3.6.1.4.1.89.12.8
ripsapCircuit	1.3.6.1.4.1.89.12.8.2
ripsapSystem	1.3.6.1.4.1.89.12.8.1
ripSysEntry	1.3.6.1.4.1.89.12.8.1.1.1		not-accessible	Each entry corresponds to one instance of RIP running on the system.
CTR ripSysIncorrectPackets	1.3.6.1.4.1.89.12.8.1.1.1.3	Counter	read-only	The number of times that an incorrectly formatted RIP packet was received.
INT ripSysInstance	1.3.6.1.4.1.89.12.8.1.1.1.1	INTEGER	read-write	The unique identifier of the instance of RIP to which this row corresponds. This value links the instance of RIP to an instance of IPX running on the system (i.e. the value of ripSysInstance should be the same as a value of ipxSysInstance). This value may be written only when creating a new entry in the table.
INT ripSysState	1.3.6.1.4.1.89.12.8.1.1.1.2	INTEGER	read-write	Indicates the operational state of this instance of RIP.
ripSysTable	1.3.6.1.4.1.89.12.8.1.1		not-accessible	The RIP system table.
rnd	1.3.6.1.4.1.89
INT rndAction	1.3.6.1.4.1.89.1.2	INTEGER	read-write	This variable enables the operator to perform one of the specified actions on the tables maintained by the network device. Send actions require support of proprietery File exchange protocol.
INT rndAlarmEnabling	1.3.6.1.4.1.89.35.2.2.1	INTEGER	read-write	Indicates whether alarms should be issued to the high-level NMS
INT rndAlarmInterval	1.3.6.1.4.1.89.35.2.2.2	INTEGER	read-write	Indicates the minimal period of time which must pass after issuing an alarm before issuing the same alarm again.
INT rndAlarmMaxTreshold	1.3.6.1.4.1.89.35.2.4.1.8	INTEGER	read-write	The value of the monitored object instance, the exceeding of which will cause the generation of an alarm to the high-level management station.
INT rndAlarmMinTreshold	1.3.6.1.4.1.89.35.2.4.1.9	INTEGER	read-write	If the value of the monitored object instance falls below the value assigned to rndAlarmMinTreshold, an alarm to the high-level management station will be issued.
rndAlarmOptions	1.3.6.1.4.1.89.35.2.2
rndApplications	1.3.6.1.4.1.89.35
rndBootP	1.3.6.1.4.1.89.24
INT rndBootPRelaySecThreshold	1.3.6.1.4.1.89.24.2	INTEGER	read-write	BootP requests are relayed only if their SEC field is greater or equal to the threshold value in order to allow local BootP Servers to answer first.
IP rndBootPServerAddress	1.3.6.1.4.1.89.24.1	IpAddress	read-write	The IPAddress of the BOOTP server. the OpenGate will act as a BootP relay if this parameter is not equale to 0.0.0.0.
OCT rndBrgFeatures	1.3.6.1.4.1.89.2.5	OCTET STRING	read-only	A bit mask that defines the features supported by a particular configuration of this network element: __________________________________________ \| Byte 1\|Byte 2 \|Byte 3 \| ....\|Byte 20 \| \|87654321\| \| 87654321\| \|________\|_______________________________\| Byte1 : bit1: TX Block mask bit2: Source Routing Encapulation bit3: SNA/SDLC bit4: Frame Relay bit5: SNMP bit6: LAN Manager bit7: High Performance bit8: Translation Byte2 : bit1: DEC Router bit2: IPX Router bit3: IP Router Byte3 : bit1: Dial Up Backup bit2: COD bit3: FACS bit4: Load Balance bit5: Remote Configuration bit6: RIP 2 bit7: OSPF bit8: IPX RIP/SAP Filter Byte4 : bit1: BootP Server bit2: BootP Client bit3: Compression bit4: V25.bis bit5: ISDN bit6: CODv2 bit7: NSPF bit8: UDP Relay Byte5 bit1:VirtualLAN bit2:Static IP Multicast bit3:IP Redundancy bit4:CCM2 bit5:ISDN Bonding bit6:Backup Link Selection -- for the VAN/Rdapter ver 4.0 bit7:IP/IPX Forwarding -- for the WANgate ver 4.0 bit8:Improved COD Byte6 bit1: Server Disptacher bit2: ISDN_US -- for the VANSX/WANGATE ver 5.0 bit3: PPP bit4: IP Rip Filter -- for Vgate3 bit5: Zero Hop Routing -- for Vgate3 bit6: ISDN Japan Byte7 bit1: With unmanaged Switch bit2: 2 LANs bit3: OSPF Ver 2.0 bit4: FACS Ver 2.0 bit5: Multiple WEB Farm bit6: Backup Server
OCT rndBrgLicense	1.3.6.1.4.1.89.2.6	OCTET STRING	read-write	This parameter is used for entering a s/w license number for a device. A separate license number is supplied for each device.
STR rndBrgVersion	1.3.6.1.4.1.89.2.4	DisplayString	read-only	The bridge version.
rndBridgeAlarm	1.3.6.1.4.1.89.2.3
INT rndBridgeType	1.3.6.1.4.1.89.2.1	INTEGER	read-only	Identification of the RND bridge type.
INT rndCommunityAccess	1.3.6.1.4.1.89.2.7.2.1.3	INTEGER	read-write	The allowed access to this management station
rndCommunityEntry	1.3.6.1.4.1.89.2.7.2.1		not-accessible	The row definition for this table.
IP rndCommunityMngStationAddr	1.3.6.1.4.1.89.2.7.2.1.1	IpAddress	read-write	The management station that will be allowed to communicate with the agent IP address
INT rndCommunityStatus	1.3.6.1.4.1.89.2.7.2.1.5	INTEGER	read-write	The status of this entry. If the status is invalid the community entry will be deleted
STR rndCommunityString	1.3.6.1.4.1.89.2.7.2.1.2	DisplayString	read-write	The community string with which the management station will communicate with the agent
rndCommunityTable	1.3.6.1.4.1.89.2.7.2		not-accessible	The community table of the agent
INT rndCommunityTrapsEnable	1.3.6.1.4.1.89.2.7.2.1.4	INTEGER	read-write	Should the agent send traps to the management station
STR rndDefaultLogFile	1.3.6.1.4.1.89.35.2.3.1.5	DisplayString	read-write	The default file path of the log-file which will contain the polling results for the monitored element. If no other file path is specifically assigned to the monitored object instance, this log-file will be used.
INT rndDefaultPollingInterval	1.3.6.1.4.1.89.35.2.3.1.4	INTEGER	read-write	The default period of time between two consecutive pollings of the monitored element for the value of an object instance. If no other polling interval is specifically assigned to the monitored object instance, this one will be used
ROW rndDeleteValueEntryStatus	1.3.6.1.4.1.89.35.2.8.1.4	RowStatus	read-write	It is used to delete an entry from this table.
rndDeleteValuesEntry	1.3.6.1.4.1.89.35.2.8.1		not-accessible	The row definition for the rndDeleteValuesTable table.
rndDeleteValuesTable	1.3.6.1.4.1.89.35.2.8		not-accessible	This table indicates which MIB variables are row status fields which control the status of the entry to which they belong. This table also indicates which (integer!) value of these MIB variables will cause, if present in a SNMP SET PDU, the deletion of the conceptual row instance to which the SET MIB variable instance belongs.
rndDeviceParams	1.3.6.1.4.1.89.2
INT rndDuplexMode	1.3.6.1.4.1.89.4.1.1.18	INTEGER	read-write	This variable indicates whether this interface operates in half duplex full duplex or auto negotiation mode.
INT rndEraseSimulatedConfiguration	1.3.6.1.4.1.89.35.2.7	INTEGER	read-write	eraseSimulatedConfiguration instructs the MLNMS to erase all the simulated configuration from its configuration data-base (CDB). This the only accepted value for SNMP SET statements and will never be returned in SNMP GET statements. simulatedConfigurationPresent indicates that the MLNMS currently has a simulated configuration. simulatedConfigurationErased indicates that the MLNMS currently has no simulated configuration.
STR rndErrorDesc	1.3.6.1.4.1.89.2.3.1	DisplayString	read-only	A textual description of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
INT rndErrorSeverity	1.3.6.1.4.1.89.2.3.2	INTEGER	read-only	The severity type of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
rndFACS	1.3.6.1.4.1.89.16
rndFACSActEntry	1.3.6.1.4.1.89.16.2.1		not-accessible	Each rndFACSActEntry consist of the following parameters
INT rndFACSActIfIndex	1.3.6.1.4.1.89.16.2.1.2	INTEGER	read-only	The interface to which this FACS entry is applicable.
INT rndFACSAction	1.3.6.1.4.1.89.16.2.1.3	INTEGER	read-write	The management station that sends a SET request for one of these actions with indexes rndFACSType and rndFACSIfIndex defines the type and the interface Id for which all FACS statements are to be erased. If no interface or no type is specified, all FACS statements for a protocol are erased.
rndFACSActTable	1.3.6.1.4.1.89.16.2		not-accessible	The table of FACS action.
INT rndFACSActType	1.3.6.1.4.1.89.16.2.1.1	INTEGER	read-only	This parameter indicate on which FACS Table the FACS action will preform.
INT rndFACSDefaultAction	1.3.6.1.4.1.89.16.1	INTEGER	read-write	Used to define the default action for the device, when no FACS statements applicable to a given frame are defined.
OCT rndFACSDesAdd	1.3.6.1.4.1.89.16.3.1.7	OCTET STRING	read-write	Destination-address The size of the octet string will be according to the protocol type define in rndFACSProtocolType .
OCT rndFACSDesAddMask	1.3.6.1.4.1.89.16.3.1.8	OCTET STRING	read-write	Destination-address mask .
rndFACSEntry	1.3.6.1.4.1.89.16.3.1		not-accessible	Each FACS statment consist of the following parameters
INT rndFACSIfIndex	1.3.6.1.4.1.89.16.3.1.1	INTEGER	read-only	The interface to which this FACS entry is applicable.
INT rndFACSIndex	1.3.6.1.4.1.89.16.3.1.4	INTEGER	read-only	Index to the FACS Table.
INT rndFACSMask1Id	1.3.6.1.4.1.89.16.3.1.12	INTEGER	read-write	Index into RND mask table FACS/COD Type) .
INT rndFACSMask2Id	1.3.6.1.4.1.89.16.3.1.13	INTEGER	read-write	Index into RND mask table FACS/COD according to the value of rndFACSType .
INT rndFACSNetFiltering	1.3.6.1.4.1.89.16.3.1.10	INTEGER	read-write	... .
INT rndFACSOperation	1.3.6.1.4.1.89.16.3.1.9	INTEGER	read-write	... .
INT rndFACSProtocolType	1.3.6.1.4.1.89.16.3.1.2	INTEGER	read-only	This parameter define the protocol the Security Access Control is applicable.
INT rndFACSSoketNum	1.3.6.1.4.1.89.16.3.1.11	INTEGER	read-write	Port/socket number for different applications 0 is default meaning not applicable.
OCT rndFACSSrcAdd	1.3.6.1.4.1.89.16.3.1.5	OCTET STRING	read-write	The size of the octet string will be according to the protocol type define in rndFACSProtocolType.
OCT rndFACSSrcAddMask	1.3.6.1.4.1.89.16.3.1.6	OCTET STRING	read-write	Source-address mask .
INT rndFACSStatus	1.3.6.1.4.1.89.16.3.1.14	INTEGER	read-write	The status of a table entry.
rndFACSTable	1.3.6.1.4.1.89.16.3		not-accessible	The table of FACS statment.
INT rndFACSType	1.3.6.1.4.1.89.16.3.1.3	INTEGER	read-only	The Mode of in which this FACS statement operates.
OCT rndFileName	1.3.6.1.4.1.89.1.3	OCTET STRING	read-write	The name of the file used internally by RND for transferring tables maintained by network devices, using a prorietary File exchange protocol.
T/F rndHardwareConfiguration	1.3.6.1.4.1.89.35.2.6	TruthValue	read-write	Indicates whether the current SET SNMP PDU contains hardware configuration (i.e., normally read-only variables). SET of such variables in the Mid-level management station will be allowed only if this variable is included in the SNMP PDU and its value is true. Its value as returned in a GET SNMP PDU will always be false.
INT rndHighPriorityIf	1.3.6.1.4.1.89.4.1.1.16	INTEGER	read-write	This variable indicates whether this interface will forward pakages that fit HighPriority set by the manager.
INT rndICMPTransmitionEnable	1.3.6.1.4.1.89.2.7.1	INTEGER	read-write	This variable controlls the ability to transmit ICMP frames
INT rndIfBaudRate	1.3.6.1.4.1.89.4.1.1.6	INTEGER	read-write	Defines the baud rate of use by the interface. The valid rates are determined by the type of the media for which this baud rate is defined.
INT rndIfBoardNum	1.3.6.1.4.1.89.4.1.1.2	INTEGER	read-only	The interface defined by this entry correspTnds to the board defined by the same value of rndSlotBoardNum in the rndSlotTab.
INT rndIfBridge	1.3.6.1.4.1.89.4.1.1.15	INTEGER	read-write	This variable indicates whether this interface forward Layer II pakages.
INT rndIfChannelType	1.3.6.1.4.1.89.4.1.1.14	INTEGER	read-write	The type of the WAN channel
INT rndIfClockType	1.3.6.1.4.1.89.4.1.1.5	INTEGER	read-write	rndIfClockType defines the type of clock each interface uses: internal or external.
INT rndIfCompression	1.3.6.1.4.1.89.4.1.1.8	INTEGER	read-write	Defines whether data compression is enabled or disabled for the interface.
INT rndIfCompressionRate	1.3.6.1.4.1.89.4.1.1.10	INTEGER	read-only	Percentage of compression. This variable applies only if rndCompressionStatus is active.
INT rndIfCompressionStatus	1.3.6.1.4.1.89.4.1.1.9	INTEGER	read-only	Defines the status of the compression component: not-inserted - Compression component is not in the device active - Compression is enabled and operates correctly not-active - Compression is enables but does not operate. The reason may be that there is no compression component on the device connected to this interface. disabled - Compression was disabled by management, using variable rndCompression.
INT rndIfCompressionType	1.3.6.1.4.1.89.4.1.1.12	INTEGER	read-only	This parameter indicates the type of compression option available in the device. none(1) - indicates that there is no compression option in the device lowSpeed(2) - indicates a compression option which is operational up to line speed sof 64 kbps. highSpeed(3)- indicates a compression option which is operational up to line speeds of 2 Mbps.
INT rndIfCost	1.3.6.1.4.1.89.4.1.1.7	INTEGER	read-write	This variable assigns a transmission cost to the interface (channel or LAN). These costs are used in Level II routing. The costs aretypically inversly proportional to the channel quality.
rndIfEntry	1.3.6.1.4.1.89.4.1.1		not-accessible	The row definition for this table.
INT rndIfFilterMode	1.3.6.1.4.1.89.4.1.1.13	INTEGER	read-write	This parameter indicates the type of filtering in the device.
INT rndIfIndex	1.3.6.1.4.1.89.4.1.1.1	INTEGER	read-only	Index to the RND Interface Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIBII).
INT rndIfLATCompression	1.3.6.1.4.1.89.4.1.1.11	INTEGER	read-write	Enable/Disable the LAT Compression.
IP rndIfNetAddress	1.3.6.1.4.1.89.4.1.1.3	IpAddress	read-only	The IP address of the interface defined by the particular value of rndIfIndex.
INT rndIfStatus	1.3.6.1.4.1.89.4.1.1.4	INTEGER	read-only	The current status of the interface.
rndIfTable	1.3.6.1.4.1.89.4.1		not-accessible	RND-specific interface table. Each table entry includes an index, Board number, Network Address, interface status, clock indicator and interface cost.
INT rndInactiveArpTimeOut	1.3.6.1.4.1.89.2.2	INTEGER	read-write	This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
rndInterface	1.3.6.1.4.1.89.4
rndIpHost	1.3.6.1.4.1.89.2.7
rndIPX	1.3.6.1.4.1.89.12
rndIPXdriver	1.3.6.1.4.1.89.12.1
rndIPXRip	1.3.6.1.4.1.89.12.2
INT rndIPXRipFilterCircFLaction	1.3.6.1.4.1.89.12.2.11.1.7	INTEGER	read-write	Filter action - permit/deny
INT rndIPXRipFilterCircFLIfIndex	1.3.6.1.4.1.89.12.2.11.1.1	INTEGER	read-only	The Interface identifier for this filter. This value correspond to rndIPXIfIndex or ipxCircIndex for ET16
OCT rndIPXRipFilterCircFLnetworkMask	1.3.6.1.4.1.89.12.2.11.1.6	OCTET STRING	read-write	Network mask
OCT rndIPXRipFilterCircFLnetworkPatern	1.3.6.1.4.1.89.12.2.11.1.5	OCTET STRING	read-write	Number of filtered network. Value 0xFFFFFFFF applies for any network.
INT rndIPXRipFilterCircFLnumber	1.3.6.1.4.1.89.12.2.11.1.3	INTEGER	read-only	Number of RIP filter for this circuit
INT rndIPXRipFilterCircFLStatus	1.3.6.1.4.1.89.12.2.11.1.4	INTEGER	read-write	The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
INT rndIPXRipFilterCircFLType	1.3.6.1.4.1.89.12.2.11.1.2	INTEGER	read-only	Type of filter - input/output
rndIPXRipFilterCircuitEntry	1.3.6.1.4.1.89.12.2.11.1		not-accessible	An entry in the Circuit RIP filter table
rndIPXRipFilterCircuitTable	1.3.6.1.4.1.89.12.2.11		not-accessible	Table of input/output RIP filters used per IPX circuit number.
rndIPXRipFilterGlbEntry	1.3.6.1.4.1.89.12.2.10.1		not-accessible	An entry in the RIP global filter table
INT rndIPXRipFilterGlbFLaction	1.3.6.1.4.1.89.12.2.10.1.6	INTEGER	read-write	Filter action - permit/deny for this network
OCT rndIPXRipFilterGlbFLnetworkMask	1.3.6.1.4.1.89.12.2.10.1.5	OCTET STRING	read-write	Network mask
OCT rndIPXRipFilterGlbFLnetworkPatern	1.3.6.1.4.1.89.12.2.10.1.4	OCTET STRING	read-write	Number of filtered network. Value 0xFFFFFFFF applies for any network.
INT rndIPXRipFilterGlbFLnumber	1.3.6.1.4.1.89.12.2.10.1.2	INTEGER	read-only	Number of RIP filter.
INT rndIPXRipFilterGlbFLStatus	1.3.6.1.4.1.89.12.2.10.1.3	INTEGER	read-write	The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
INT rndIPXRipFilterGlbFLtype	1.3.6.1.4.1.89.12.2.10.1.1	INTEGER	read-only	Type of filter - input/output
rndIPXRipFilterGlbTable	1.3.6.1.4.1.89.12.2.10		not-accessible	The table of RIP global filters per IPX router.
rndIPXSap	1.3.6.1.4.1.89.12.3
INT rndIPXSapFilterCircFLaction	1.3.6.1.4.1.89.12.3.11.1.9	INTEGER	read-write	Filter mode-permit/deny
INT rndIPXSapFilterCircFLIfIndex	1.3.6.1.4.1.89.12.3.11.1.1	INTEGER	read-only	The Interface identifier for this filter. This value correspondtornd IPXIfIndex or ipxCircIndex for ET16
OCT rndIPXSapFilterCircFLnetworkMask	1.3.6.1.4.1.89.12.3.11.1.6	OCTET STRING	read-write	Network mask
OCT rndIPXSapFilterCircFLnetworkPatern	1.3.6.1.4.1.89.12.3.11.1.5	OCTET STRING	read-write	Number network of the filtered service. Value 0xFFFFFFFF applies for any network.
INT rndIPXSapFilterCircFLnumber	1.3.6.1.4.1.89.12.3.11.1.3	INTEGER	read-only	Number of SAP filter. Th is value correspondto rndIPXSapFilterNumber
OCT rndIPXSapFilterCircFLserviceName	1.3.6.1.4.1.89.12.3.11.1.8	OCTET STRING	read-write	The name of the service which may be filtered; wild cardas * may be used i n end of the name.
INT rndIPXSapFilterCircFLserviceType	1.3.6.1.4.1.89.12.3.11.1.7	INTEGER	read-write	The type of the service which may be filtered; value 0xFFFF applies for all types of service and it's default
INT rndIPXSapFilterCircFLStatus	1.3.6.1.4.1.89.12.3.11.1.4	INTEGER	read-write	The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
INT rndIPXSapFilterCircFLtype	1.3.6.1.4.1.89.12.3.11.1.2	INTEGER	read-only	Type of filter-input/output
rndIPXSapFilterCircuitEntry	1.3.6.1.4.1.89.12.3.11.1		not-accessible	An entry in the Circuit SAP filter table
rndIPXSapFilterCircuitTable	1.3.6.1.4.1.89.12.3.11		not-accessible	Table of input/output SAP filter susedper IPX circuit number.
rndIPXSapFilterGlbEntry	1.3.6.1.4.1.89.12.3.10.1		not-accessible	An entry in the SAP global filter table
INT rndIPXSapFilterGlbFLaction	1.3.6.1.4.1.89.12.3.10.1.8	INTEGER	read-write	Filter mode - permit/deny for this service
OCT rndIPXSapFilterGlbFLnetworkMask	1.3.6.1.4.1.89.12.3.10.1.5	OCTET STRING	read-write	Network mask
OCT rndIPXSapFilterGlbFLnetworkPatern	1.3.6.1.4.1.89.12.3.10.1.4	OCTET STRING	read-write	Number network of the filter edservice. Value 0xFFFFFFFF applies for any network.
INT rndIPXSapFilterGlbFLnumber	1.3.6.1.4.1.89.12.3.10.1.2	INTEGER	read-only	Number of SAP filter.
OCT rndIPXSapFilterGlbFLserviceName	1.3.6.1.4.1.89.12.3.10.1.7	OCTET STRING	read-write	The name of the service which may be filtered; wild cardas * may be used in end of the name.
INT rndIPXSapFilterGlbFLserviceType	1.3.6.1.4.1.89.12.3.10.1.6	INTEGER	read-write	The type of the service which may be filtered ;value0xFFFF applies for all types of service and it's default
INT rndIPXSapFilterGlbFLStatus	1.3.6.1.4.1.89.12.3.10.1.3	INTEGER	read-write	The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
INT rndIPXSapFilterGlbFLtype	1.3.6.1.4.1.89.12.3.10.1.1	INTEGER	read-only	Type of filter-input/output
rndIPXSapFilterGlbTable	1.3.6.1.4.1.89.12.3.10		not-accessible	The table of SAP global filter susedper IPX router.
STR rndManagedDate	1.3.6.1.4.1.89.2.9	DisplayString	read-write	The date will be sent in the format ddmmyyyy
STR rndManagedTime	1.3.6.1.4.1.89.2.8	DisplayString	read-write	The time will be sent in the format hhmmss
rndMibFileEntry	1.3.6.1.4.1.89.35.2.5.1		not-accessible	The row definition for this table.
ROW rndMibFileEntryStatus	1.3.6.1.4.1.89.35.2.5.1.4	RowStatus	read-write	It is used to manage the MIB files table.
INT rndMibFileIndex	1.3.6.1.4.1.89.35.2.5.1.1	INTEGER	read-only	The number of the MIB file in the list MIB files supported by the Mid-Level management station. The order of the MIB files in this list must reflect the the IMPORT relation between the MIBS contained in the MIB files, i.e., if MIB A IMPORTS FROM MIB B, the file containing MIB A must have a lesser index in this table than the file containing MIB B.
STR rndMibFilePath	1.3.6.1.4.1.89.35.2.5.1.2	DisplayString	read-write	The path of the MIB file in the MIB file server.
INT rndMibFileRefresh	1.3.6.1.4.1.89.35.2.5.1.3	INTEGER	read-write	Indicates if the file should be fetched after setting this entry from the MIB file server.
rndMibFilesTable	1.3.6.1.4.1.89.35.2.5		not-accessible	The table of monitored object instances. Each monitored object instance belongs to a monitored element previously entered in the rndMonitoredElementsTable.
rndMidLevelManagement	1.3.6.1.4.1.89.35.2
rndMng	1.3.6.1.4.1.89.1
STR rndMonitoredElement	1.3.6.1.4.1.89.35.2.4.1.1	DisplayString	read-only	A label assigned by the network manager to a monitored element to which this monitored object instance belongs. This label must have been previously entered in an instance of rndMonitoredElementLabel
IP rndMonitoredElementAddress	1.3.6.1.4.1.89.35.2.3.1.1	IpAddress	read-only	The IP address of the monitored element
STR rndMonitoredElementCommunity	1.3.6.1.4.1.89.35.2.3.1.2	DisplayString	read-write	The community of the monitored element
rndMonitoredElementEntry	1.3.6.1.4.1.89.35.2.3.1		not-accessible	The row definition for this table.
STR rndMonitoredElementLabel	1.3.6.1.4.1.89.35.2.3.1.3	DisplayString	read-write	The label assigned by the network manager to the monitored element
rndMonitoredElementsTable	1.3.6.1.4.1.89.35.2.3		not-accessible	The table of monitored elements of the network
ROW rndMonitoredElementStatus	1.3.6.1.4.1.89.35.2.3.1.6	RowStatus	read-write	It is used to manage the monitored elements table and indicates the current monitoring status of an element.
OID rndMonitoredObjectIdentifier	1.3.6.1.4.1.89.35.2.4.1.4	OBJECT IDENTIFIER	read-write	The object identifier of the object to which the monitored object instance belongs. An instance of rndMonitoredObjectIdentifier need not be assigned any value, if the corresponding instance of rndMonitoredObjectName is assigned a value, since any one of these, together with the object instance identifier, suffices to unambigously identify the monitored object instance.
OID rndMonitoredObjectInstance	1.3.6.1.4.1.89.35.2.4.1.5	OBJECT IDENTIFIER	read-write	The instance identifier (key) of the monitored object instance.
STR rndMonitoredObjectInstanceLabel	1.3.6.1.4.1.89.35.2.4.1.2	DisplayString	read-only	The label assigned by the network manager to the monitored object instance
STR rndMonitoredObjectName	1.3.6.1.4.1.89.35.2.4.1.3	DisplayString	read-write	The symbolic object type name of the object to which the monitored object instance belongs (as it appears the MIB module definition). In case of ambiguity the : format should be used. An instance of rndMonitoredObjectName need not be assigned any value, if the corresponding instance of rndMonitoredObjectIdentifier is assigned a value, since any one of these, together with the object instance identifier, suffices to unambigously identify the monitored object instance.
INT rndMonitoredObjectSyntax	1.3.6.1.4.1.89.35.2.4.1.6	INTEGER	read-write	The syntax of the monitored object instance (i.e., the syntax of the object type of the object to which the monitored instance belongs). Need not be assigned any value if the corresponding instance of rndMonitoredObjectName has been assigned a value
rndMonitoringEntry	1.3.6.1.4.1.89.35.2.4.1		not-accessible	The row definition for this table.
ROW rndMonitoringEntryStatus	1.3.6.1.4.1.89.35.2.4.1.11	RowStatus	read-write	It is used to manage the monitored object instances table and indicates the current monitoring status of an object instance.
INT rndMonitoringInterval	1.3.6.1.4.1.89.35.2.4.1.7	INTEGER	read-write	The period of time between two consecutive retrievals of the monitored object instance's value.
STR rndMonitoringLogfile	1.3.6.1.4.1.89.35.2.4.1.10	DisplayString	read-write	The entire path of the file in which the results of the monitoring of this object instance should be recorded.
rndMonitoringTable	1.3.6.1.4.1.89.35.2.4		not-accessible	The table of monitored object instances. Each monitored object instance belongs to a monitored element previously entered in the rndMonitoredElementsTable.
INT rndRowDeleteValue	1.3.6.1.4.1.89.35.2.8.1.3	INTEGER	read-write	The value of the variable identified by rndRowStatusVariableName and/or rndRowStatusObjectId, which, if present in a SNMP SET PDU, will cause the deletion of the conceptual row instance which the SET MIB variable instance belongs.
OID rndRowStatusObjectId	1.3.6.1.4.1.89.35.2.8.1.2	OBJECT IDENTIFIER	read-write	The object id of the row status field. If the rndRowStatusVariableName is a name present in the MIBs loaded into the MLNMS, this MIB variable is not required, but if given, it must match the object id known to the MLNMS. The variable identified by rndRowStatusVariableName and/or rndRowStatusObjectId must be a read-write MIB variable of type INTEGER which belongs to an entry (i.e, is a child of a MIB variable of type SEQUENCE).
STR rndRowStatusVariableName	1.3.6.1.4.1.89.35.2.8.1.1	DisplayString	read-write	The name of the row status field. This name may not necessarily be any name which is present in the MIBs loaded into the MLNMS station.
INT rndSysId	1.3.6.1.4.1.89.1.1	INTEGER	read-only	Identification of an RND device. The device type for each integer clarifies the sysObjectID in MIB - II.
INT rndWanHeader	1.3.6.1.4.1.89.4.1.1.17	INTEGER	read-write	This variable indicates the RND WAN header type used for frames which pass through this interface. 'regular' specifies a 14 bytes header compatible with older OG versions and 'short' a 4 byte header compatible with the RND adapter product family.
NTF routeTableOverflow	1.3.6.1.4.1.89.0.5			An overflow condition has occurred in the Routing Table. The Routing Table is used for IP routing algorithm (RIP).
INT rsArpDeleteTable	1.3.6.1.4.1.89.26.4.1	INTEGER	read-write	Setting this object to any not-null value has the effect of deleting all entries of the ARP table.
INT rsArpInactiveTimeOut	1.3.6.1.4.1.89.26.4.2	INTEGER	read-write	This variable defines the maximum time period (in second) that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
INT rsArpProxy	1.3.6.1.4.1.89.26.4.3	INTEGER	read-write	When ARP Proxy is enabled, the router can respond to ARP requests for nodes located on a different sub-net, provided they are it its network table. The router responds with its own MAC address. When ARP Proxy is disabled, the router responds only to ARP requests for its own IP addresses.
rsConf	1.3.6.1.4.1.89.28
INT rsConfirmMessagTab	1.3.6.1.4.1.89.29.5	INTEGER	read-write	This variable enables the operator to confirm all the message in the event Message Table.
INT rsDbgLevel	1.3.6.1.4.1.89.29.3	INTEGER	read-write	This variable indicates the debug level the Router Server works. the range of this variable is 1..100
STR rsDiagnostic	1.3.6.1.4.1.89.29.4	DisplayString	read-only	This variable will contain some dignostic information in case on a problem ocurs in the RS functinality.
IP rsFileServerAddress	1.3.6.1.4.1.89.26.5.6	IpAddress	read-write	The IP address of the configuration / sw server.
STR rsGetConfigFile	1.3.6.1.4.1.89.26.5.4	DisplayString	read-write	The file name include path where the Router Server will get the configuration. The default source address will be the sender address.
INT rsHighPriority	1.3.6.1.4.1.89.29.1	INTEGER	read-write	This variable indicates the time interval the forwarding task inside the RS works in High Priority Mode.
INT rsIcmpGenErrMsgEnable	1.3.6.1.4.1.89.26.2.1	INTEGER	read-write	This variable controlls the ability to generate ICMP error messages
INT rsIcmpRdAdvertise	1.3.6.1.4.1.89.26.2.2.1.6	INTEGER	read-write	A flag indicating whether or not the address is to be advertised.
INT rsIcmpRdAdvertLifetime	1.3.6.1.4.1.89.26.2.2.1.5	INTEGER	read-write	The maximum length of time that the advertised addresses are to be considered as valid. Must be no less than rsIcmpRdMaxAdvertInterval and no greater than 9000 seconds. Default: 3 * rsIcmpRdMaxAdvertInterval.
rsIcmpRdEntry	1.3.6.1.4.1.89.26.2.2.1		not-accessible	The ICMP parameters configurated for IP interface.
INT rsIcmpRdEntStatus	1.3.6.1.4.1.89.26.2.2.1.8	INTEGER	read-write	Setting of any value to this object set values of all fields to the default values.
IP rsIcmpRdIpAddr	1.3.6.1.4.1.89.26.2.2.1.1	IpAddress	read-only	The IP address to which this entry's information pertains.
IP rsIcmpRdIpAdvertAddr	1.3.6.1.4.1.89.26.2.2.1.2	IpAddress	read-write	The IP destination address to be used for multicast Router Advertisements sent from the interface. The only permissible values are the all-systems multicast address, 224.0.0.1, or the limited-broadcast address, 255.255.255.255.
INT rsIcmpRdMaxAdvertInterval	1.3.6.1.4.1.89.26.2.2.1.3	INTEGER	read-write	The maximum time allowed between sending multicast Router Advertisements from the interface, in seconds. Must be no less than 4 seconds and no greater than 1800 seconds.
INT rsIcmpRdMinAdvertInterval	1.3.6.1.4.1.89.26.2.2.1.4	INTEGER	read-write	The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface, in seconds. Must be no less than 3 seconds and no greater than rsIcmpRdMaxAdvertInterval. Default: 0.75 * rsIcmpRdMaxAdvertInterval.
INT rsIcmpRdPreferenceLevel	1.3.6.1.4.1.89.26.2.2.1.7	INTEGER	read-write	The preferability of the address as a default router address, relative to other router addresses on the same subnet.
rsIcmpRdTable	1.3.6.1.4.1.89.26.2.2		not-accessible	This table contains ICMP Router Discovery parameters configurated per IP interface.
rsIfConfEntry	1.3.6.1.4.1.89.28.1.1		not-accessible	Each entry defines a configured interface.
INT rsIfConfIndex	1.3.6.1.4.1.89.28.1.1.1	INTEGER	read-only	This variable uniquely identifies the interface. It is used as a cross reference in other system tables
STR rsIfConfName	1.3.6.1.4.1.89.28.1.1.3	DisplayString	read-write	This variable provides a logical name to a specific entry in rsIfConfTable
ROW rsIfConfStatus	1.3.6.1.4.1.89.28.1.1.4	RowStatus	read-write	The status of the ConfigEntry. The choices are those defined in SNMPv2-TC. Only: active, createAndWait, and destroy will be used. active - The conceptual row is available for use by the managed device. createAndWait - A new instance of a conceptual row is desired, but not to have it available for use by the managed device. destroy - Delete all instances associated with an existing conceptual row.
rsIfConfTable	1.3.6.1.4.1.89.28.1		not-accessible	This table enable the user to add interface to the RS. RS will automatically add the new interface to the interface Table
RSI rsIfConfType	1.3.6.1.4.1.89.28.1.1.2	RsIfType	read-write	This variable identifies the type of the specific entry in the rsIfConfTable. This field is writable only at creation time (i.e., when value of status is underCreation).
rsIpAddrEntry	1.3.6.1.4.1.89.26.1.1		not-accessible	The addressing information for one of this entity's IP addresses.
rsIpAddrTable	1.3.6.1.4.1.89.26.1		not-accessible	This table is parralel to MIB II IpAddrTable, and is used to add/delete entries to/from that table. In addition it contains private objects.
IP rsIpAdEntAddr	1.3.6.1.4.1.89.26.1.1.1	IpAddress	read-only	The IP address to which this entry's addressing information pertains.
IP rsIpAdEntBackupAddr	1.3.6.1.4.1.89.26.1.1.5	IpAddress	read-write
INT rsIpAdEntBcastAddr	1.3.6.1.4.1.89.26.1.1.7	INTEGER	read-write	Indicates how the host part of ip subnet broadcast messages will be filled: 0 - host part will be filled by 0 1 - host part will be filled by 1.
INT rsIpAdEntForwardIpBroadcast	1.3.6.1.4.1.89.26.1.1.4	INTEGER	read-write	This variable controls forwarding of IP (sub)net-directed broadcasts destined for an attached sub(net).
INT rsIpAdEntIfIndex	1.3.6.1.4.1.89.26.1.1.2	INTEGER	read-write	The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP rsIpAdEntNetMask	1.3.6.1.4.1.89.26.1.1.3	IpAddress	read-write	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
INT rsIpAdEntStatus	1.3.6.1.4.1.89.26.1.1.6	INTEGER	read-write	The validity of this entry. Invalid indicates that this entry is invalid in IpAddrTable (MIB II).
INT rsIpRipFilterGlbAction	1.3.6.1.4.1.89.26.8.1.1.7	INTEGER	read-write	Filter action - permit/deny for this network
rsIpRipFilterGlbEntry	1.3.6.1.4.1.89.26.8.1.1		not-accessible	An entry in the RIP global filter table
IP rsIpRipFilterGlbIpAddr	1.3.6.1.4.1.89.26.8.1.1.4	IpAddress	read-write	network prefix IP address, as in the forwarding table.
INT rsIpRipFilterGlbMatchBits	1.3.6.1.4.1.89.26.8.1.1.6	INTEGER	read-write	the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterGlbNetworkMaskBits must be 0 and is ignored.
INT rsIpRipFilterGlbNetworkMaskBits	1.3.6.1.4.1.89.26.8.1.1.5	INTEGER	read-write	the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0
INT rsIpRipFilterGlbNumber	1.3.6.1.4.1.89.26.8.1.1.2	INTEGER	read-only	Number of RIP filter.
INT rsIpRipFilterGlbStatus	1.3.6.1.4.1.89.26.8.1.1.3	INTEGER	read-write	The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.
rsIpRipFilterGlbTable	1.3.6.1.4.1.89.26.8.1		not-accessible	The table of RIP global filters per IP router.
INT rsIpRipFilterGlbType	1.3.6.1.4.1.89.26.8.1.1.1	INTEGER	read-only	Type of filter - input/output
INT rsIpRipFilterLclAction	1.3.6.1.4.1.89.26.8.2.1.8	INTEGER	read-write	Filter action - permit/deny
rsIpRipFilterLclEntry	1.3.6.1.4.1.89.26.8.2.1		not-accessible	An entry in the Intf RIP filter table
IP rsIpRipFilterLclIpAddr	1.3.6.1.4.1.89.26.8.2.1.5	IpAddress	read-write	network prefix IP address, as in the forwarding table.
IP rsIpRipFilterLclIpIntf	1.3.6.1.4.1.89.26.8.2.1.1	IpAddress	read-only	The IP address identifying the RIP interface for this filter. This value corresponds to rsIpAdEntAddr.
INT rsIpRipFilterLclMatchBits	1.3.6.1.4.1.89.26.8.2.1.7	INTEGER	read-write	the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterLclNetworkMaskBits must be 0 and is ignored.
INT rsIpRipFilterLclNetworkMaskBits	1.3.6.1.4.1.89.26.8.2.1.6	INTEGER	read-write	the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0
INT rsIpRipFilterLclNumber	1.3.6.1.4.1.89.26.8.2.1.3	INTEGER	read-only	Number of RIP filter for this Interface
INT rsIpRipFilterLclStatus	1.3.6.1.4.1.89.26.8.2.1.4	INTEGER	read-write	The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.
rsIpRipFilterLclTable	1.3.6.1.4.1.89.26.8.2		not-accessible	Table of input/output RIP filters used per IP Interface.
INT rsIpRipFilterLclType	1.3.6.1.4.1.89.26.8.2.1.2	INTEGER	read-only	Type of filter - input/output
rsIpZeroHopRouting	1.3.6.1.4.1.89.35.3
INT rsIpZhrAdminStatus	1.3.6.1.4.1.89.35.3.3.1.2	INTEGER	read-write	It is used to control whether ZHR will operate on the interface.
INT rsIpZhrAgingTimeout	1.3.6.1.4.1.89.35.3.2	INTEGER	read-write	This parameter controls the aging time-out in seconds of direct connections which were allocated. The virtual IP address of a direct connection whose time-out has expired is eligible for allocation to a different connection.
INT rsIpZhrConnectionAge	1.3.6.1.4.1.89.35.3.5.1.6	INTEGER	read-only	The age of the connection in seconds.
IP rsIpZhrConnectionDestIp	1.3.6.1.4.1.89.35.3.5.1.3	IpAddress	read-only	The destination IP Address of this direct connection.
rsIpZhrConnectionEntry	1.3.6.1.4.1.89.35.3.5.1		not-accessible	An entry in the ZHR Connection table
IP rsIpZhrConnectionIpIntf	1.3.6.1.4.1.89.35.3.5.1.1	IpAddress	read-only	The IP Interface for which this direct connection was established.
IP rsIpZhrConnectionSrcIp	1.3.6.1.4.1.89.35.3.5.1.2	IpAddress	read-only	The source IP Address of this direct connection.
rsIpZhrConnectionsTable	1.3.6.1.4.1.89.35.3.5		not-accessible	Table of the currently active direct connections.
NTF rsIpZhrConnectionsTableOverflow	1.3.6.1.4.1.89.0.70			The Zero Hop Routing connections Table has been overflown.
ROW rsIpZhrConnectionStatus	1.3.6.1.4.1.89.35.3.5.1.7	RowStatus	read-write	It is used to manage the connections table. The supported actions will be active, createAndGo and destroy.
INT rsIpZhrConnectionType	1.3.6.1.4.1.89.35.3.5.1.5	INTEGER	read-only	The type of this direct connection. dynamic - established by the RS. disabled - established by the RS. The RS detected that the virtual address is already used as destination by the source BEFORE its allocation, and therefore marked this connection as 'disabled' to prevent a future allocation of this virtual address to this source. static - established by user.
IP rsIpZhrConnectionVirtualIp	1.3.6.1.4.1.89.35.3.5.1.4	IpAddress	read-only	The virtual IP address allocated for this direct connection.
INT rsIpZhrGeneralStatus	1.3.6.1.4.1.89.35.3.1	INTEGER	read-write	This parameter enables or disables the IP Zero Hop Routing feature for all IP interfaces. The IP Zero Hop Routing feature can also be enabled or disabled on each IP interface through the rsIpZhrStatusTable.
NTF rsIpZhrNotAllocVirtualIp	1.3.6.1.4.1.89.0.73			The source IP address sent an ARP specifying a virtual IP which was not allocated for this source. This virtual IP will not be allocated to connections of this specific source IP.
NTF rsIpZhrReqStaticConnNotAccepted	1.3.6.1.4.1.89.0.71			The requested static connection was not accepted because there is no available IP virtual address to allocate to it.
rsIpZhrStatusEntry	1.3.6.1.4.1.89.35.3.3.1		not-accessible	An entry in the ZHR status table.
IP rsIpZhrStatusIpIntf	1.3.6.1.4.1.89.35.3.3.1.1	IpAddress	read-only	The Ip interface whose ZHR feature status is accessed.
rsIpZhrStatusTable	1.3.6.1.4.1.89.35.3.3		not-accessible	The administrative status of the ZHR feature per ip interface.
rsIpZhrVirtAddressEntry	1.3.6.1.4.1.89.35.3.4.1		not-accessible	An entry in the ZHR virtual IP addresses table
IP rsIpZhrVirtAddressFrom	1.3.6.1.4.1.89.35.3.4.1.3	IpAddress	read-write	The first free IP address in the block.
IP rsIpZhrVirtAddressIpIntf	1.3.6.1.4.1.89.35.3.4.1.1	IpAddress	read-only	The Ip Interface to which the IP addresses in this entry are allocated.
ROW rsIpZhrVirtAddressStatus	1.3.6.1.4.1.89.35.3.4.1.4	RowStatus	read-write	It is used to manage the virtual address table. The supported actions will be active, createAndGo and destroy.
rsIpZhrVirtAddressTable	1.3.6.1.4.1.89.35.3.4		not-accessible	The table of free virtual IP addresses which may be allocated to establish direct connections - Per IP Interface.
IP rsIpZhrVirtAddressTo	1.3.6.1.4.1.89.35.3.4.1.2	IpAddress	read-only	The last free IP address in the block.
NTF rsIpZhrVirtualIpAsSource	1.3.6.1.4.1.89.0.72			The virtual IP address appeared as a source IP. All the connections using it will be deleted and it will not be further allocated to new connections.
STR rsLoadSoftware	1.3.6.1.4.1.89.26.5.5	DisplayString	read-write	The file name include path where the Router Server will get the software. The source address will the sender address.
INT rsLowPriority	1.3.6.1.4.1.89.29.2	INTEGER	read-write	This variable indicates the time interval the forwarding task inside the RS works in Low Priority Mode.
INT rsMaxArpEntries	1.3.6.1.4.1.89.29.8.3.1	INTEGER	read-only	Maximal number of entries in Arp forwarding table.
INT rsMaxArpEntriesAfterReset	1.3.6.1.4.1.89.29.8.3.2	INTEGER	read-write	Future maximal number of entries in Arp forwarding table.
rsMaxArpEntriesTuning	1.3.6.1.4.1.89.29.8.3
INT rsMaxBrgFrwEntries	1.3.6.1.4.1.89.29.8.1.1	INTEGER	read-only	Maximal number of entries in bridge forwarding table.
INT rsMaxBrgFrwEntriesAfterReset	1.3.6.1.4.1.89.29.8.1.2	INTEGER	read-write	Future maximal number of entries in bridge forwarding table.
rsMaxBridgeForwardingEntriesTuning	1.3.6.1.4.1.89.29.8.1
INT rsMaxDspClntEntries	1.3.6.1.4.1.89.29.8.6.1	INTEGER	read-only	Maximal number of entries in rsSdClientsTable.
INT rsMaxDspClntEntriesAfterReset	1.3.6.1.4.1.89.29.8.6.2	INTEGER	read-write	Future maximal number of entries in rsSdClientsTable.
rsMaxDspClntEntriesTuning	1.3.6.1.4.1.89.29.8.6
INT rsMaxDspFrmEntries	1.3.6.1.4.1.89.29.8.8.1	INTEGER	read-only	Maximal number of entries in rsSdClientsTable.
INT rsMaxDspFrmEntriesAfterReset	1.3.6.1.4.1.89.29.8.8.2	INTEGER	read-write	Future maximal number of entries in rsSdClientsTable.
rsMaxDspFrmEntriesTuning	1.3.6.1.4.1.89.29.8.8
rsMaxEntriesTuning	1.3.6.1.4.1.89.29.8
rsMaxIpForwardingEntriesTuning	1.3.6.1.4.1.89.29.8.2
INT rsMaxIpFrwEntries	1.3.6.1.4.1.89.29.8.2.1	INTEGER	read-only	Maximal number of entries in Ip forwarding table.
INT rsMaxIpFrwEntriesAfterReset	1.3.6.1.4.1.89.29.8.2.2	INTEGER	read-write	Future maximal number of entries in Ip forwarding table.
rsMaxIpxForwardingEntriesTuning	1.3.6.1.4.1.89.29.8.4
INT rsMaxIpxFrwEntries	1.3.6.1.4.1.89.29.8.4.1	INTEGER	read-only	Maximal number of entries in Ipx forwarding table.
INT rsMaxIpxFrwEntriesAfterReset	1.3.6.1.4.1.89.29.8.4.2	INTEGER	read-write	Future maximal number of entries in Ipx forwarding table.
INT rsMaxIpxSapEntries	1.3.6.1.4.1.89.29.8.5.1	INTEGER	read-only	Maximal number of entries in IpxSap table.
INT rsMaxIpxSapEntriesAfterReset	1.3.6.1.4.1.89.29.8.5.2	INTEGER	read-write	Future maximal number of entries in IpxSap table.
rsMaxIpxSapEntriesTuning	1.3.6.1.4.1.89.29.8.5
rsMaxZeroHopRoutEntriesTuning	1.3.6.1.4.1.89.29.8.7
INT rsMaxZhrConns	1.3.6.1.4.1.89.29.8.7.1	INTEGER	read-only	The current maximal number of direct Zero-hop routing connections.
INT rsMaxZhrConnsAfterReset	1.3.6.1.4.1.89.29.8.7.2	INTEGER	read-write	The future (after reset) maximal number of direct Zero-hop routing connections.
IP rsRip2IfConfAddress	1.3.6.1.4.1.89.26.3.1.1.1	IpAddress	read-only	The IP Address of this system on the indicated subnet.
INT rsRip2IfConfAutoSend	1.3.6.1.4.1.89.26.3.1.1.3	INTEGER	read-write	This variable controls RIP automatic send behavior. If enabled and no routers were heard on the interface, RIP will only send default route with high metric. Otherwise RIP will send updates according to configuration.
rsRip2IfConfEntry	1.3.6.1.4.1.89.26.3.1.1		not-accessible
rsRip2IfConfTable	1.3.6.1.4.1.89.26.3.1		not-accessible	This table is extension of rip2IfConfTable (RFC 1389 ,RIP 2)
INT rsRip2IfConfVirtualDis	1.3.6.1.4.1.89.26.3.1.1.2	INTEGER	read-write	This variable defines the virtual number of hops assigned to the interface specified by rsIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm.
INT rsRipEnable	1.3.6.1.4.1.89.26.9	INTEGER	read-write	Enables or disables RIP.
NTF rsSDclientsTableOverflow	1.3.6.1.4.1.89.0.68			This warning is generated when an overflow occurs in the clients table.
NTF rsSDinactiveServer	1.3.6.1.4.1.89.0.69			This warning is generated when a server does not respond to the dispatchers polling and is thought to be inactive.
STR rsSendConfigFile	1.3.6.1.4.1.89.26.5.3	DisplayString	read-write	The file name include path where the Router Server will put the full configuration. The default destination address will be the sender address.
rsServerDispatcher	1.3.6.1.4.1.89.35.1
NTF rsSnmpSetRequestInSpecialCfgState	1.3.6.1.4.1.89.0.74			An incoming SNMP SET request was rejected because no such requests (except action requests) are accepted after start of new configuration reception or during sending the current configuration to an NMS.
INT rsTftpRetryTimeOut	1.3.6.1.4.1.89.26.5.1	INTEGER	read-write	General Retransmission time-out value (seconds)
INT rsTftpTotalTimeOut	1.3.6.1.4.1.89.26.5.2	INTEGER	read-write	Total Retransmission time-out value (seconds)
rsTunning	1.3.6.1.4.1.89.29
NTF rsWSDRedundancySwitch	1.3.6.1.4.1.89.0.141			Whenever main server fails and backup takes over or server comes up after failure a trap of this type is issued.
INT sapCircAgeMultiplier	1.3.6.1.4.1.89.12.8.2.2.1.5	INTEGER	read-write	The holding multiplier for information received in SAP periodic updates.
sapCircEntry	1.3.6.1.4.1.89.12.8.2.2.1		not-accessible	Each entry corresponds to one circuit known to the system.
INT sapCircGetNearestServerReply	1.3.6.1.4.1.89.12.8.2.2.1.6	INTEGER	read-write	Indicates whether to respond to SAP get nearest server requests received on this circuit.
INT sapCircIndex	1.3.6.1.4.1.89.12.8.2.2.1.2	INTEGER	read-write	The identifier of this circuit, unique within the instance of SAP. This value corresponds to the circuit identifier found in ipxCircIndex. This value may be written only when creating a new entry in the table.
CTR sapCircInPackets	1.3.6.1.4.1.89.12.8.2.2.1.8	Counter	read-only	The number of SAP packets received on this circuit.
CTR sapCircOutPackets	1.3.6.1.4.1.89.12.8.2.2.1.7	Counter	read-only	The number of SAP packets sent on this circuit.
INT sapCircState	1.3.6.1.4.1.89.12.8.2.2.1.3	INTEGER	read-write	Indicates whether SAP information may be sent/received over this circuit.
INT sapCircSysInstance	1.3.6.1.4.1.89.12.8.2.2.1.1	INTEGER	read-write	The unique identifier of the instance of SAP and IPX (via ipxSysInstance) to which this entry corresponds. This value may be written only when creating a new entry in the table.
sapCircTable	1.3.6.1.4.1.89.12.8.2.2		not-accessible	The SAP Circuit table.
INT sapCircUpdate	1.3.6.1.4.1.89.12.8.2.2.1.4	INTEGER	read-write	The SAP periodic update interval, in seconds.
sapSysEntry	1.3.6.1.4.1.89.12.8.1.2.1		not-accessible	Each entry corresponds to one instance of SAP running on the system.
CTR sapSysIncorrectPackets	1.3.6.1.4.1.89.12.8.1.2.1.3	Counter	read-only	The number of times that an incorrectly formatted SAP packet was received.
INT sapSysInstance	1.3.6.1.4.1.89.12.8.1.2.1.1	INTEGER	read-write	The unique identifier of the instance of SAP to which this row corresponds. This value links the instance of SAP to an instance of IPX running on the system (i.e. the value of SApSysInstance should be the same as a value of ipxSysInstance). This value may be written only when creating a new entry in the table.
INT sapSysState	1.3.6.1.4.1.89.12.8.1.2.1.2	INTEGER	read-only	Indicates the operational state of this instance of SAP.
sapSysTable	1.3.6.1.4.1.89.12.8.1.2		not-accessible	The SAP system table.
NTF startTftp	1.3.6.1.4.1.89.0.14			Informational trap indicating that the device has intiated a TFTP session. rndErrorDesc will contain the file type in question
tftp	1.3.6.1.4.1.89.26.5
virtualLan	1.3.6.1.4.1.89.27
INT virtualLanAutoConfAgingTimeout	1.3.6.1.4.1.89.27.4	INTEGER	read-write	The units of this MIB object is seconds. Its value can be either 0 or in range 10..65535 .
virtualLanAutoConfEntry	1.3.6.1.4.1.89.27.3.1		not-accessible	One port, specified by vlAutoConfPortIfIndex, for which the RS will automatically learn its VL in accordance with rules, defined by the protocol specified in vlAutoConfProto.
virtualLanAutoConfTable	1.3.6.1.4.1.89.27.3		not-accessible	This table specifies per a routing protocol a set of ports, from which RS will automatically learning VL in accordance with rules, defined by the protocol.
virtualLanEntry	1.3.6.1.4.1.89.27.1.1		not-accessible	A list of information for each virtual LAN.
virtualLanPortEntry	1.3.6.1.4.1.89.27.2.1		not-accessible	A entry of this table specifies a VL and a port belonging to it
virtualLanPortsTable	1.3.6.1.4.1.89.27.2		not-accessible	For each VL (a ifIndex with a type of propVirtual(53)) an entry of this table specifies a set of ports, which it contains.
virtualLanProtocolVlan	1.3.6.1.4.1.89.27.5
virtualLanTable	1.3.6.1.4.1.89.27.1		not-accessible	An entry of this table specifies an new ifIndex with a type of propVirtual(53).
OCT virtualLanUserEtherType	1.3.6.1.4.1.89.27.5.1	OCTET STRING	read-write
OCT virtualLanUserMask	1.3.6.1.4.1.89.27.5.2	OCTET STRING	read-write
NTF vlanDynPortAdded	1.3.6.1.4.1.89.0.66
NTF vlanDynPortRemoved	1.3.6.1.4.1.89.0.67
T/F vlAutoConfigEnable	1.3.6.1.4.1.89.27.1.1.3	TruthValue	read-write	It is used only in the case of IP. The meanings of the values are: true(1): Autolearning is used for this VL false(2): Autolearning isn't used for this VL from ports, specified in the table virtualLanAutoConfTable.
INT vlAutoConfPortIfIndex	1.3.6.1.4.1.89.27.3.1.1	INTEGER	read-write	Port on which the autoconfig option should be supported
INT vlAutoConfProto	1.3.6.1.4.1.89.27.3.1.2	INTEGER	read-only	Protocol for which the autoconfig option is supported for the port specified by vlAutoConfPortIfIndex
ROW vlAutoConfStatus	1.3.6.1.4.1.89.27.3.1.3	RowStatus	read-write	It is used to delete an entry
INT vLIfIndex	1.3.6.1.4.1.89.27.1.1.1	INTEGER	read-write	An logical interface number, corresponded this VL
INT vLPortIfIndex	1.3.6.1.4.1.89.27.2.1.2	INTEGER	read-write	A physical port belonging to the VL specified by vlIfIndex.
ROW vLPortStatus	1.3.6.1.4.1.89.27.2.1.4	RowStatus	read-write	It is used to delete an entry
INT vLPortType	1.3.6.1.4.1.89.27.2.1.3	INTEGER	read-only	static means configured by user dynamic means autoconfigured by the RS
INT vlProto	1.3.6.1.4.1.89.27.1.1.2	INTEGER	read-write	The protocol, supported by this VL. The meanings of the values are: other: none of the following. This VL includes any protocol except the following protocols. It is a bridging VL. RS relies on a third-party router to exchange traffic between nodes on different virtual LANs of this type. IP: This is a routing VL, RS will route between nodes on different virtual LANs. IPmulticast: RS will broadcast the message to all the VL's ports. Used for video-conferencing applications. ipxRaw: This is a Routing VL, RS will route between nodes on different virtual LANs. ipxET: This is a routing VL, RS will route between nodes on different virtual LANs. ipxLLC: This is a routing VL, RS will route between nodes on different virtual LANs. ipxSNAP: This is a routing VL, RS will route between nodes on different virtual LANs. decNET: This is a bridging VL, RS relies on a third-party router to exchange traffic between nodes on different DECnet virtual LANs of this type. netBios: This is a Bridging VL, RS relies on a third-party router to exchange traffic between nodes on different NetBIOS virtual LANs of this type. appleTalk: This is a bridging VL, RS relies on a third-party router to exchange traffic between nodes on different AppleTalk virtual LANs of this type.
ROW vlStatus	1.3.6.1.4.1.89.27.1.1.4	RowStatus	read-write	It is used to delete an entry
INT vlType	1.3.6.1.4.1.89.27.1.1.5	INTEGER	read-write	regular - ordinary type specBroadcast - for switches that support VLANs as a set of ports and only as a broadcast domain: broadcast frames do not cross VLAN's bounders, but unicast frames may be transmitted between different VLANs. Permits passing of broadcast frames between Vgate's VLANs. specArpReq - for switches that support VLANs as a set of ports and only as a broadcast domain: broadcast frames do not cross VLAN's bounders, but unicast frames may be transmitted between different VLANs. Permits passing of ARP request frames between Vgate's VLANs. specBroadcastAndUnicast - for switches that support VLANs as a set of ports but no frame crosses VLAN's bounders. Permits passing of IP/ARP request broadcast and IP unicast frames between Vgate's VLANs. specArpReqAndUnicast - for switches that support VLANs as a set of ports but no frame crosses VLAN's bounders. Permits passing of ARP request broadcast and IP unicast frames between Vgate's VLANs. This type can be used only for IP VLANs.

RFC description

Comprehensive management MIB for RAD Network Devices (RND) Vgate systems, covering bridging, routing, interfaces, and various network protocols across modular devices.

Start monitoring RAD Data Communications network access devices with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RND-MIB

What Is RND-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description