RC7586-MIB

All MIBs › RC7586-MIB

Organization: Codan Limited.

Last Updated: 2009-05-13

Category: Vendor: Codan

Description: Provides management objects for Codan RC7586 satellite and HF radio modem configuration and operational status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RC7586-MIB?

RC7586-MIB is a Codan enterprise MIB for the RC7586 satellite/HF radio modem product, covering its operational configuration and status reporting. It exposes objects for operational mode, online stream state, waveguide switch position, LNB (low-noise block) current limit, reference oscillator source/trim/threshold/power, startup time, and basic network addressing (IP/MAC). For monitoring, it is used to confirm the modem's RF front-end and reference clock are healthy -- checking refPwr/refThresh and lnbCurrentLimit for signs of antenna or LNB hardware faults, ledState for a quick front-panel-equivalent status check, and onlineStream to confirm the satellite link is actively passing traffic. As a small vendor enterprise MIB, it has no significant dependency on external standard MIBs. It is deployed in remote/rural satellite backhaul or broadcast-distribution sites using Codan RC7586 modems, where remote SNMP polling substitutes for physical access to the equipment. Engineers can download the RC7586-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RC7586-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Codan RC7586 satellite/HF radio modem

Monitoring Examples

An operator would poll onlineStream and operationalMode to confirm the RC7586 modem is actively locked and passing satellite traffic, and check refPwr against refThresh to detect a degraded reference signal that could indicate an antenna alignment or LNB fault. lnbCurrentLimit would be monitored for signs of an LNB hardware failure (over-current or no-current condition), and ledState gives a quick remote proxy for the unit's front-panel status indicators. startupTime helps confirm whether the unit has recently rebooted unexpectedly.

What Can Be Monitored

operational mode and online stream status
reference oscillator power/threshold
LNB current limit
waveguide switch position
unit startup time
front-panel LED state

Imported Objects

From CODAN-SMI

satcomMibs

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DateAndTime
DisplayString
TEXTUAL-CONVENTION
TestAndIncr
TimeInterval
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
buc1	1.3.6.1.4.1.23304.2.2.1
INT buc1Address	1.3.6.1.4.1.23304.2.2.1.1.2.2	INTEGER	read-write	Sets/Gets packet address: 0-31 NDSatcom ...Respond -1 if buc1 not connected.
STR buc1BuildStandard	1.3.6.1.4.1.23304.2.2.1.2.17	DisplayString	read-only	Gets the BUC build standard. **** No respond - message if buc1 not connected.
STR buc1BurstPwrThresh	1.3.6.1.4.1.23304.2.2.1.1.5.3	DisplayString	read-write	Sets/Gets burst power threshold. **** No respond - message if buc1 not connected.
STR buc1Config	1.3.6.1.4.1.23304.2.2.1.2.16	DisplayString	read-only	Gets the BUC configuration. **** No respond - message if buc1 not connected.
buc1Configuration	1.3.6.1.4.1.23304.2.2.1.1
STR buc1DeviceType	1.3.6.1.4.1.23304.2.2.1.2.10	DisplayString	read-only	Gets the device type. Format is X,Y where X is the model and Y is software version. **** No respond - message if buc1 not connected.
INT buc1Faults	1.3.6.1.4.1.23304.2.2.1.2.4	INTEGER	read-only	Gets the current fault status. Format - Bit0 PA fault, Bit1 Fan fault, Bit2 Power fault, Bit3 Temp fault, Bit4 10MHz fault, Bit5 Internal fault Bit6 LNB fault, Bit7 Red'cy Cont fault. Respond -1 if buc2 not connected.
buc1Freqs	1.3.6.1.4.1.23304.2.2.1.1.4
STR buc1Gateway	1.3.6.1.4.1.23304.2.2.1.2.11	DisplayString	read-only	Gets the BUC gateway address (Only for RBUC). **** No respond - message if buc1 not connected.
STR buc1IdInfo	1.3.6.1.4.1.23304.2.2.1.3.1	DisplayString	read-only	Gets the module firmware revision, serial number and model. This string will have a zero length if the revision is unknown. **** No respond - message if buc1 not connected.
INT buc1IFFreq	1.3.6.1.4.1.23304.2.2.1.1.4.2	INTEGER	read-write	Sets/Gets the RBUC IF frequency. Respond -1 if buc1 not connected.
buc1Info	1.3.6.1.4.1.23304.2.2.1.3
STR buc1IpAddress	1.3.6.1.4.1.23304.2.2.1.2.12	DisplayString	read-only	Gets the BUC IP address (Only for RBUC). **** No respond - message if buc1 not connected.
INT buc1LatchedFaults	1.3.6.1.4.1.23304.2.2.1.2.5	INTEGER	read-only	Gets the current latched faults. Format is same as Faults. Respond -1 if buc2 not connected.
STR buc1LEDState	1.3.6.1.4.1.23304.2.2.1.1.5.5	DisplayString	read-write	Sets/Gets LEDs status on/off (Only for RBUC). **** No respond - message if buc1 not connected.
STR buc1Limits	1.3.6.1.4.1.23304.2.2.1.3.2	DisplayString	read-only	Gets the limit data for the BUC. Format is: Power meter MIN/MAX , IF,RF and LO frequencies. This string will have a zero length if the revision is unknown. **** No respond - message if buc1 not connected.
INT buc1LOFreq	1.3.6.1.4.1.23304.2.2.1.1.4.3	INTEGER	read-write	Sets/Gets the RBUC LO frequency. Respond -1 if buc1 not connected.
STR buc1MACAddress	1.3.6.1.4.1.23304.2.2.1.2.13	DisplayString	read-only	Gets the BUC MAC address (Only for RBUC). **** No respond - message if buc1 not connected.
STR buc1MinMaxTemperature	1.3.6.1.4.1.23304.2.2.1.2.7	DisplayString	read-only	Gets the BUC temperature. Format is x.x,y.y where x.x is max and y.y is min temperature. **** No respond - message if buc1 not connected.
buc1Misc	1.3.6.1.4.1.23304.2.2.1.1.5
INT buc1Mode	1.3.6.1.4.1.23304.2.2.1.1.3.1	INTEGER	read-write	Sets/Gets redundancy mode 0-none, 1-warm, 2-hot. Respond -1 if buc1 not connected.
STR buc1Netmask	1.3.6.1.4.1.23304.2.2.1.2.14	DisplayString	read-only	Gets the BUC netmask (Only for RBUC). **** No respond - message if buc1 not connected.
T/F buc1OnLine	1.3.6.1.4.1.23304.2.2.1.1.3.2	TruthValue	read-write	Sets/Gets redundancy mode on on/off line state. Respond -1 if buc1 not connected.
INT buc1PaStatus	1.3.6.1.4.1.23304.2.2.1.2.1	INTEGER	read-only	Gets to 1 when PA is on. Respond -1 if buc1 not connected.
buc1PktProtocol	1.3.6.1.4.1.23304.2.2.1.1.2
STR buc1PktProtocolsInfo	1.3.6.1.4.1.23304.2.2.1.3.3	DisplayString	read-only	Gets supported packet protocols and the corresponding address ranges. **** No respond - message if buc1 not connected.
INT buc1Protocol	1.3.6.1.4.1.23304.2.2.1.1.2.1	INTEGER	read-write	Sets/Gets packet protocol 0 - ASCII, 1 - CODAN, 2 - SAbus, 3 - Comstream, 4 - NDSatcom. Respond -1 if buc1 not connected.
STR buc1PwrAlarmThresh	1.3.6.1.4.1.23304.2.2.1.1.5.2	DisplayString	read-write	Sets/Gets power alarm threshold. **** No respond - message if buc1 not connected.
buc1RCSetting	1.3.6.1.4.1.23304.2.2.1.1.3
STR buc1RefPower	1.3.6.1.4.1.23304.2.2.1.2.15	DisplayString	read-only	Gets the BUC reference power. **** No respond - message if buc1 not connected.
STR buc1RefSource	1.3.6.1.4.1.23304.2.2.1.1.5.4	DisplayString	read-write	Sets/Gets reference source 0-external, 1-internal (Only for RBUC). **** No respond - message if buc1 not connected.
INT buc1RFFreq	1.3.6.1.4.1.23304.2.2.1.1.4.1	INTEGER	read-write	Sets/Gets the RBUC RF frequency. Respond -1 if buc1 not connected.
STR buc1SerIf	1.3.6.1.4.1.23304.2.2.1.1.5.1	DisplayString	read-write	Sets/Gets serial interface - rate, length, parity, stop, terminate RS422/485. **** No respond - message if buc1 not connected.
buc1Status	1.3.6.1.4.1.23304.2.2.1.2
INT buc1SystemPoll	1.3.6.1.4.1.23304.2.2.1.2.9	INTEGER	read-only	Gets the system poll status. Format is Bit0 - Fault, Bit1 - System change. Respond -1 if buc1 not connected.
INT buc1SystemSetting	1.3.6.1.4.1.23304.2.2.1.2.8	INTEGER	read-only	Gets the current system status. Format is Bit0 - PA state, Bit1 - RS232 Tx, Bit2 - FSK Tx, Bit3 - RS485 Tx Bit4 - Redundancy mode, Bit5 - Online, Bit6..Bit7 - Redundancy cold or hot mode, Bit8 - HTTP Tx, Bit9 - TELNET Tx, Bit10 - SNMP Tx. Respond -1 if buc1 not connected.
STR buc1Temperature	1.3.6.1.4.1.23304.2.2.1.2.6	DisplayString	read-only	Gets the BUC temperature. Format is x.x. **** No respond - message if buc1 not connected.
INT buc1TxAttenuator	1.3.6.1.4.1.23304.2.2.1.1.1.3	INTEGER	read-write	Sets/Gets Tx attenuation value in 1dBm steps. Respond -1 if buc1 not connected.
STR buc1TxBurstPower	1.3.6.1.4.1.23304.2.2.1.2.3	DisplayString	read-only	Gets Tx power. Format is x.x,y.y,z.z, where x.x is current burst power, y.y is min and z.z is max burts power. **** No respond - message if buc1 not connected.
INT buc1TxDefault	1.3.6.1.4.1.23304.2.2.1.1.1.2	INTEGER	read-write	Sets Tx default 1-last 0-off. Respond -1 if buc1 not connected.
INT buc1TxOn	1.3.6.1.4.1.23304.2.2.1.1.1.1	INTEGER	read-write	Sets Tx on/off. Respond -1 if buc1 not connected.
STR buc1TxPower	1.3.6.1.4.1.23304.2.2.1.2.2	DisplayString	read-only	Gets Tx power format x.x dB. **** No respond - message if buc1 not connected.
buc1TxSettings	1.3.6.1.4.1.23304.2.2.1.1.1
buc2	1.3.6.1.4.1.23304.2.2.2
INT buc2Address	1.3.6.1.4.1.23304.2.2.2.1.2.2	INTEGER	read-write	Sets/Gets packet address: 0-31 NDSatcom ...Respond -1 if buc2 not connected.
STR buc2BuildStandard	1.3.6.1.4.1.23304.2.2.2.2.17	DisplayString	read-only	Gets the BUC build standard. **** No respond - message if buc2 not connected.
STR buc2BurstPwrThresh	1.3.6.1.4.1.23304.2.2.2.1.5.3	DisplayString	read-write	Sets/Gets burst power threshold. **** No respond - message if buc2 not connected.
STR buc2Config	1.3.6.1.4.1.23304.2.2.2.2.16	DisplayString	read-only	Gets the BUC configuration. **** No respond - message if buc2 not connected.
buc2Configuration	1.3.6.1.4.1.23304.2.2.2.1
STR buc2DeviceType	1.3.6.1.4.1.23304.2.2.2.2.10	DisplayString	read-only	Gets the device type. Format is X,Y where X is the model and Y is software version. **** No respond - message if buc2 not connected.
INT buc2Faults	1.3.6.1.4.1.23304.2.2.2.2.4	INTEGER	read-only	Gets the current fault status. Format - Bit0 PA fault, Bit1 Fan fault, Bit2 Power fault, Bit3 Temp fault, Bit4 10MHz fault, Bit5 Internal fault Bit6 LNB fault, Bit7 Red'cy Cont fault. Respond -1 if buc2 not connected.
buc2Freqs	1.3.6.1.4.1.23304.2.2.2.1.4
STR buc2Gateway	1.3.6.1.4.1.23304.2.2.2.2.11	DisplayString	read-only	Gets the BUC gateway address (Only for RBUC). **** No respond - message if buc2 not connected.
STR buc2IdInfo	1.3.6.1.4.1.23304.2.2.2.3.1	DisplayString	read-only	Gets the module firmware revision, serial number and model. This string will have a zero length if the revision is unknown. **** No respond - message if buc2 not connected.
INT buc2IFFreq	1.3.6.1.4.1.23304.2.2.2.1.4.2	INTEGER	read-write	Sets/Gets the RBUC IF frequency. Respond -1 if buc2 not connected.
buc2Info	1.3.6.1.4.1.23304.2.2.2.3
STR buc2IpAddress	1.3.6.1.4.1.23304.2.2.2.2.12	DisplayString	read-only	Gets the BUC IP address (Only for RBUC). **** No respond - message if buc2 not connected.
INT buc2LatchedFaults	1.3.6.1.4.1.23304.2.2.2.2.5	INTEGER	read-only	Gets the current latched faults. Format is same as Faults. Respond -1 if buc2 not connected.
STR buc2LEDState	1.3.6.1.4.1.23304.2.2.2.1.5.5	DisplayString	read-write	Sets/Gets LEDs status on/off (Only for RBUC). **** No respond - message if buc2 not connected.
STR buc2Limits	1.3.6.1.4.1.23304.2.2.2.3.2	DisplayString	read-only	Gets the limit data for the BUC. Format is: Power meter MIN/MAX , IF,RF and LO frequencies. This string will have a zero length if the revision is unknown. **** No respond - message if buc2 not connected.
INT buc2LOFreq	1.3.6.1.4.1.23304.2.2.2.1.4.3	INTEGER	read-write	Sets/Gets the RBUC LO frequency. Respond -1 if buc2 not connected.
STR buc2MACAddress	1.3.6.1.4.1.23304.2.2.2.2.13	DisplayString	read-only	Gets the BUC MAC address (Only for RBUC). **** No respond - message if buc2 not connected.
STR buc2MinMaxTemperature	1.3.6.1.4.1.23304.2.2.2.2.7	DisplayString	read-only	Gets the BUC temperature. Format is x.x,y.y where x.x is max and y.y is min temperature. **** No respond - message if buc2 not connected.
buc2Misc	1.3.6.1.4.1.23304.2.2.2.1.5
INT buc2Mode	1.3.6.1.4.1.23304.2.2.2.1.3.1	INTEGER	read-write	Sets/Gets redundancy mode 0-none, 1-warm, 2-hot. Respond -1 if buc2 not connected.
STR buc2Netmask	1.3.6.1.4.1.23304.2.2.2.2.14	DisplayString	read-only	Gets the BUC netmask (Only for RBUC). **** No respond - message if buc2 not connected.
T/F buc2OnLine	1.3.6.1.4.1.23304.2.2.2.1.3.2	TruthValue	read-write	Sets/Gets redundancy mode on on/off line state. Respond -1 if buc2 not connected.
INT buc2PaStatus	1.3.6.1.4.1.23304.2.2.2.2.1	INTEGER	read-only	Gets to 1 when PA is on. Respond -1 if buc2 not connected.
buc2PktProtocol	1.3.6.1.4.1.23304.2.2.2.1.2
STR buc2PktProtocolsInfo	1.3.6.1.4.1.23304.2.2.2.3.3	DisplayString	read-only	Gets supported packet protocols and the corresponding address ranges. **** No respond - message if buc2 not connected.
INT buc2Protocol	1.3.6.1.4.1.23304.2.2.2.1.2.1	INTEGER	read-write	Sets/Gets packet protocol 0 - ASCII, 1 - CODAN, 2 - SAbus, 3 - Comstream, 4 - NDSatcom. Respond -1 if buc2 not connected.
STR buc2PwrAlarmThresh	1.3.6.1.4.1.23304.2.2.2.1.5.2	DisplayString	read-write	Sets/Gets power alarm threshold. **** No respond - message if buc2 not connected.
buc2RCSetting	1.3.6.1.4.1.23304.2.2.2.1.3
STR buc2RefPower	1.3.6.1.4.1.23304.2.2.2.2.15	DisplayString	read-only	Gets the BUC reference power. **** No respond - message if buc2 not connected.
STR buc2RefSource	1.3.6.1.4.1.23304.2.2.2.1.5.4	DisplayString	read-write	Sets/Gets reference source 0-external, 1-internal (Only for RBUC). **** No respond - message if buc2 not connected.
INT buc2RFFreq	1.3.6.1.4.1.23304.2.2.2.1.4.1	INTEGER	read-write	Sets/Gets the RBUC RF frequency. Respond -1 if buc2 not connected.
STR buc2SerIf	1.3.6.1.4.1.23304.2.2.2.1.5.1	DisplayString	read-write	Sets/Gets serial interface - rate, length, parity, stop, terminate RS422/485. **** No respond - message if buc2 not connected.
buc2Status	1.3.6.1.4.1.23304.2.2.2.2
INT buc2SystemPoll	1.3.6.1.4.1.23304.2.2.2.2.9	INTEGER	read-only	Gets the system poll status. Format is Bit0 - Fault, Bit1 - System change. Respond -1 if buc2 not connected.
INT buc2SystemSetting	1.3.6.1.4.1.23304.2.2.2.2.8	INTEGER	read-only	Gets the current system status. Format is Bit0 - PA state, Bit1 - RS232 Tx, Bit2 - FSK Tx, Bit3 - RS485 Tx Bit4 - Redundancy mode, Bit5 - Online, Bit6..Bit7 - Redundancy cold or hot mode, Bit8 - HTTP Tx, Bit9 - TELNET Tx, Bit10 - SNMP Tx. Respond -1 if buc2 not connected.
STR buc2Temperature	1.3.6.1.4.1.23304.2.2.2.2.6	DisplayString	read-only	Gets the BUC temperature. Format is x.x. **** No respond - message if buc2 not connected.
INT buc2TxAttenuator	1.3.6.1.4.1.23304.2.2.2.1.1.3	INTEGER	read-write	Sets/Gets Tx attenuation value in 1dBm steps. Respond -1 if buc2 not connected.
STR buc2TxBurstPower	1.3.6.1.4.1.23304.2.2.2.2.3	DisplayString	read-only	Gets Tx power. Format is x.x,y.y,z.z, where x.x is current burst power, y.y is min and z.z is max burts power. **** No respond - message if buc2 not connected.
INT buc2TxDefault	1.3.6.1.4.1.23304.2.2.2.1.1.2	INTEGER	read-write	Sets Tx default 1-last 0-off. Respond -1 if buc2 not connected.
INT buc2TxOn	1.3.6.1.4.1.23304.2.2.2.1.1.1	INTEGER	read-write	Sets Tx on/off. Respond -1 if buc2 not connected.
STR buc2TxPower	1.3.6.1.4.1.23304.2.2.2.2.2	DisplayString	read-only	Gets Tx power format x.x dB. **** No respond - message if buc2 not connected.
buc2TxSettings	1.3.6.1.4.1.23304.2.2.2.1.1
ctrl	1.3.6.1.4.1.23304.2.2.3
INT faults	1.3.6.1.4.1.23304.2.2.3.2.3	INTEGER	read-only	Gets the current fault status.
STR gateway	1.3.6.1.4.1.23304.2.2.3.1.14	DisplayString	read-only	Gets the 7586 gateway address.
STR idInfo	1.3.6.1.4.1.23304.2.2.3.3.1	DisplayString	read-only	Gets the module firmware revision, serial number and model. This string will have a zero length if the revision is unknown.
info	1.3.6.1.4.1.23304.2.2.3.3
STR ipAddr	1.3.6.1.4.1.23304.2.2.3.1.11	DisplayString	read-only	Gets the 7586 IP address.
INT ledState	1.3.6.1.4.1.23304.2.2.3.1.6	INTEGER	read-write	Sets 7586 LED.
STR lnbCurrent	1.3.6.1.4.1.23304.2.2.3.2.1	DisplayString	read-only	Sets 7586 LNB current.
STR lnbCurrentLimit	1.3.6.1.4.1.23304.2.2.3.1.5	DisplayString	read-write	Sets LNB current limits.
STR lnbVoltage	1.3.6.1.4.1.23304.2.2.3.2.2	DisplayString	read-only	Sets 7586 LNB voltage.
STR macAddress	1.3.6.1.4.1.23304.2.2.3.1.12	DisplayString	read-only	Gets the 7586 MAC address.
STR netmask	1.3.6.1.4.1.23304.2.2.3.1.13	DisplayString	read-only	Gets the 7586 netmask.
INT onlineStream	1.3.6.1.4.1.23304.2.2.3.1.2	INTEGER	read-write	Sets the online stream.
INT operationalMode	1.3.6.1.4.1.23304.2.2.3.1.1	INTEGER	read-write	Sets 7586 operational mode - Auto, Manual Stream1, Stream2.
rc7586MIB	1.3.6.1.4.1.23304.2.2			The Structure of Management Information for the Codan enterprise. Copyright(c) 2009 All rights reserved
STR refPwr	1.3.6.1.4.1.23304.2.2.3.1.10	DisplayString	read-only	Gets 7586 reference power.
INT refSource	1.3.6.1.4.1.23304.2.2.3.1.7	INTEGER	read-write	Sets 7586 reference state.
STR refThresh	1.3.6.1.4.1.23304.2.2.3.1.9	DisplayString	read-write	Sets 7586 reference alarm treshold.
STR refTrim	1.3.6.1.4.1.23304.2.2.3.1.8	DisplayString	read-write	Sets 7586 reference trim.
settings	1.3.6.1.4.1.23304.2.2.3.1
INT startupTime	1.3.6.1.4.1.23304.2.2.3.1.4	INTEGER	read-write	Sets Startup time.
status	1.3.6.1.4.1.23304.2.2.3.2
INT waveguideSwitch	1.3.6.1.4.1.23304.2.2.3.1.3	INTEGER	read-write	Sets Waveguide switch Rx+Tx, Rx/Tx and Tx Only.

RFC description

Raritan device SNMP MIB module providing management information for RC7586 remote device management, power monitoring, and environmental telemetry across Raritan infrastructure solutions.

Start monitoring Codan RC7586 satellite/HF radio modem (RF front-end/reference-clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RC7586-MIB

What Is RC7586-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description