RAISECOM-REMOTE-MANAGEMENT-REMOTE-MIB

All MIBs › RAISECOM-REMOTE-MANAGEMENT-REMOTE-MIB

Organization: RAISECOM TECH, Ltd.

Last Updated: 2006-09-11

Description: Raisecom EFM OAM remote device management MIB exposing temperature, 3.3V and 5V supply readings, and configuration objects for remotely managed Raisecom CPE

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RAISECOM-REMOTE-MANAGEMENT-REMOTE-MIB?

RAISECOM-REMOTE-MANAGEMENT-REMOTE-MIB is a RAISECOM TECH, Ltd. proprietary MIB reporting remotely-managed device (e.g., an EOC/PON remote unit) hardware telemetry and network configuration. Its objects cover temperature, four internal supply-voltage rail readings (3.3V/2.5V/1.8V/1.2V), a system-operation trigger and its resulting state, host name, OAM-notification enable, SNMP community name/permission, Layer 3 IP address/mask/VLAN interface/member ports/untagged ports/default gateway, and a port table (ifIndex, type, name, admin/operational status, duplex/speed). As a hardware/status MIB it lets an administrator watch a remote unit's temperature and supply-rail voltages and confirm its Layer 3 management addressing. It is deployed on RAISECOM TECH remotely-managed access equipment. Engineers can download the RAISECOM-REMOTE-MANAGEMENT-REMOTE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RAISECOM-REMOTE-MANAGEMENT-REMOTE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

RAISECOM TECH remotely-managed access equipment

Monitoring Examples

An administrator monitors raisecomRemoteTemperature and raisecomRemoteVolt3300 to catch a remote unit's power-supply or thermal problem before it fails on Raisecom access equipment.

What Can Be Monitored

remote-unit temperature, supply voltages, and Layer 3 configuration

Imported Objects

From RAISECOM-BASE-MIB

raisecomAgent

OBJECT-IDENTITY

From RMON-MIB

EntryStatus

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TimeStamp
TruthValue

From SWITCH-TC

EnableVar
PortList

How to Use in IPNetwork Monitor

Example using raisecomRemoteifInDiscards OID:

Select an RAISECOM TECH remotely-managed access equipment (EOC/PON remote unit telemetry) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type raisecomRemoteifInDiscards into the Find box to locate it in the OID tree, then select it and click OK. The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
raisecomRemoteManagementRemote	1.3.6.1.4.1.8886.1.13			The MIB module defining objects for remote management on remote devices.
raisecomRemoteManagementRemoteHideMibObjects	1.3.6.1.4.1.8886.1.13.1
INT raisecomRemoteTemperature	1.3.6.1.4.1.8886.1.13.1.1	INTEGER	read-only	The current environment temperature of remote device.
INT raisecomRemoteVolt3300	1.3.6.1.4.1.8886.1.13.1.2	INTEGER	read-only	Current voltage value of 3.3v of remote device.
INT raisecomRemoteVolt2500	1.3.6.1.4.1.8886.1.13.1.3	INTEGER	read-only	Current voltage value of 2.5v of remote device.
INT raisecomRemoteVolt1800	1.3.6.1.4.1.8886.1.13.1.4	INTEGER	read-only	Current voltage value of 1.8v of remote device.
INT raisecomRemoteVolt1200	1.3.6.1.4.1.8886.1.13.1.5	INTEGER	read-only	Current voltage value of 1.2v of remote device.
INT raisecomRemoteSysOperation	1.3.6.1.4.1.8886.1.13.1.6	INTEGER	read-write	Specifies system command in remote device.Currently,support three types command:reboot,write and erase.Reboot command is used to reset remote device,write is used to save startup-config file in remote device, and erase is used to erase startup-config file of remote device.
INT raisecomRemoteSysOperationState	1.3.6.1.4.1.8886.1.13.1.7	INTEGER	read-only	Specifies the state of this system operation to remote device.
OCT raisecomRemoteHostName	1.3.6.1.4.1.8886.1.13.1.8	OCTET STRING	read-write	Host name of Remote device.
ENA raisecomRemoteOamNotificationEnable	1.3.6.1.4.1.8886.1.13.1.9	EnableVar	read-write	Specifies whether or not remote device send OAM notificaton frames.
OCT raisecomRemoteCommunityName	1.3.6.1.4.1.8886.1.13.1.10	OCTET STRING	read-write	The SNMPv1/v2c community name string in remote device. In remote device's community table,the index of this community is 3,and the view for this community is 'internet'.
INT raisecomRemoteCommunityPermission	1.3.6.1.4.1.8886.1.13.1.11	INTEGER	read-write	This object specifies the type of access allowed. 'readOnly(1)' allows GET operations (i.e., GET, GET-NEXT, GET-BULK) and 'readWrite(2)' allows both GET and SET operations.
IP raisecomRemoteL3IpAddr	1.3.6.1.4.1.8886.1.13.1.12	IpAddress	read-write	The IP Address of remote device. This IP address logically AND'ed with 'raisecomRemoteL3Mask' yields the actual subnet value for this subnet.Set the object as '0.0.0.0' means delete IP address of remote devices
IP raisecomRemoteL3Mask	1.3.6.1.4.1.8886.1.13.1.13	IpAddress	read-write	The subnet mask for this remote subnet. It contains 1's in the bit positions for the net and subnet IDs and 0's in the bit positions for host ID. The 1's must be contiguous, starting with the left most bit.
INT raisecomRemoteL3VidIface	1.3.6.1.4.1.8886.1.13.1.14	INTEGER	read-write	This object contains the actual VLAN ID (VID) from 1 to 4094. It is actually the management vlan of remote device.
POR raisecomRemoteL3VidMemberPorts	1.3.6.1.4.1.8886.1.13.1.15	PortList	read-only	The set of ports which are permanently assigned to the egress list for this VLAN by management.Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.
POR raisecomRemoteL3VidUntaggedPorts	1.3.6.1.4.1.8886.1.13.1.16	PortList	read-only	The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.
IP raisecomRemoteL3DefaultGateway	1.3.6.1.4.1.8886.1.13.1.17	IpAddress	read-write	With this object to Set or get default gateway of remote devices.
raisecomRemotePortTable	1.3.6.1.4.1.8886.1.13.1.18		not-accessible	A table of remote devices port properties.
raisecomRemotePortEntry	1.3.6.1.4.1.8886.1.13.1.18.1		not-accessible	Table entry for port control and status information in remote devices.
INT raisecomRemotePortIfindex	1.3.6.1.4.1.8886.1.13.1.18.1.2	INTEGER	not-accessible	The ifIndex value based 1 which identifies the unique interface of remote device.
INT raisecomRemotePortType	1.3.6.1.4.1.8886.1.13.1.18.1.3	INTEGER	read-only	Port type in remote devices,same as slot type.
OCT raisecomRemotePortName	1.3.6.1.4.1.8886.1.13.1.18.1.4	OCTET STRING	read-only	The port name of remote devices.
INT raisecomRemotePortAdminStatus	1.3.6.1.4.1.8886.1.13.1.18.1.5	INTEGER	read-write	The administrative state of the port on remote devices.
INT raisecomRemotePortOperStatus	1.3.6.1.4.1.8886.1.13.1.18.1.6	INTEGER	read-only	The current operational state of the interface in remote devices.
INT raisecomRemotePortDuplexSpeedSet	1.3.6.1.4.1.8886.1.13.1.18.1.7	INTEGER	read-write	The desired speed and duplex of the interface in remote devices.
INT raisecomRemotePortDuplexSpeedGet	1.3.6.1.4.1.8886.1.13.1.18.1.8	INTEGER	read-only	The actual speed and duplex for this interface. If the interface is not configured for an acceptable value, a value of illegal(99) is returned. A value of unknown(1) is returned when the interface is down.
ENA raisecomRemotePortFlowControlEnable	1.3.6.1.4.1.8886.1.13.1.18.1.9	EnableVar	read-write	Set the flow control on the interface to enable(1) or disable(2).
ENA raisecomRemotePortFlowControlStatus	1.3.6.1.4.1.8886.1.13.1.18.1.10	EnableVar	read-only	The actual port flow control status of remote device.
INT raisecomRemotePortIngressRate	1.3.6.1.4.1.8886.1.13.1.18.1.11	INTEGER	read-write	The value is the ingress rate( kbps) of the port.
INT raisecomRemotePortEgressRate	1.3.6.1.4.1.8886.1.13.1.18.1.12	INTEGER	read-write	The value is the egress rate( kbps) of the port.
ENA raisecomRemotePortFaultPassEnable	1.3.6.1.4.1.8886.1.13.1.18.1.13	EnableVar	read-write	Set fault pass to enable(1) or disable(2) on the port in remote device.
POR raisecomRemotePortFaultPassPorts	1.3.6.1.4.1.8886.1.13.1.18.1.14	PortList	read-write	The ports set which should be down when fault pass occurs.If the value is 0,stands for fault pass function is disable on this port,otherwise fault pass function is enable and the ports set specifies which ports should be down when fault pass occurs.
INT raisecomRemotePortFaultPassStatus	1.3.6.1.4.1.8886.1.13.1.18.1.15	INTEGER	read-only	Port state changging result of fault pass. If normal(1), there is no fault pass occurring. If down(2), the port is down because of fault pass occurring.
INT raisecomRemotePortFaultReturnEnable	1.3.6.1.4.1.8886.1.13.1.18.1.16	INTEGER	read-write	Set fault return on the port in remote device to enable(1) or disable(2). This value of TP is unavailable.
INT raisecomRemotePortFaultReturnStatus	1.3.6.1.4.1.8886.1.13.1.18.1.17	INTEGER	read-only	Port state changging result of fault return.If normal(1), there is no fault return occurring.If down(2), the port is down result of fault return occurring.This value of TP is unavailable.
INT raisecomRemotePortSD	1.3.6.1.4.1.8886.1.13.1.18.1.18	INTEGER	read-only	SD status. This value of TP is unavailable.
INT raisecomRemoteOptModuleType	1.3.6.1.4.1.8886.1.13.1.18.1.19	INTEGER	read-only	Optical module type of remote device port.
OCT raisecomRemotePortDescr	1.3.6.1.4.1.8886.1.13.1.18.1.20	OCTET STRING	read-write	The description of a port in remote device.
raisecomRemotePortStatsTable	1.3.6.1.4.1.8886.1.13.1.19		not-accessible	A table of remote devices port statistics.
raisecomRemotePortStatsEntry	1.3.6.1.4.1.8886.1.13.1.19.1		not-accessible	Table entry of remote devices port statistics.
INT raisecomRemoteStatsPortIfindex	1.3.6.1.4.1.8886.1.13.1.19.1.1	INTEGER	not-accessible	The ifIndex value based 1 which identifies the unique interface of remote device.
C64 raisecomRemotePortInOctets	1.3.6.1.4.1.8886.1.13.1.19.1.2	Counter64	read-only	The total number of octets received on the port.
C64 raisecomRemotePortInPkts	1.3.6.1.4.1.8886.1.13.1.19.1.3	Counter64	read-only	The total number of packets received on the port..
C64 raisecomRemotePortInUcastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.4	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.
C64 raisecomRemotePortInMulticastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.5	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses
C64 raisecomRemotePortInBroadcastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.6	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.
C64 raisecomRemotePortOutOctets	1.3.6.1.4.1.8886.1.13.1.19.1.7	Counter64	read-only	The total number of octets transmitted out of the port, including framing characters.
C64 raisecomRemotePortOutPkts	1.3.6.1.4.1.8886.1.13.1.19.1.8	Counter64	read-only	The total number of packets transmitted out of the port.
C64 raisecomRemotePortOutUcastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.9	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.
C64 raisecomRemotePortOutMulticastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.10	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses.
C64 raisecomRemotePortOutBroadcastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.11	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.
C32 raisecomRemotePortErrorPkts	1.3.6.1.4.1.8886.1.13.1.19.1.12	Counter32	read-only	The total number of bad packets received by a specific port of remote device.
C32 raisecomRemotePortDropEvents	1.3.6.1.4.1.8886.1.13.1.19.1.13	Counter32	read-only	The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
C32 raisecomRemotePortCRCAlignErrors	1.3.6.1.4.1.8886.1.13.1.19.1.14	Counter32	read-only	The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C32 raisecomRemotePortUndersizePkts	1.3.6.1.4.1.8886.1.13.1.19.1.15	Counter32	read-only	The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C32 raisecomRemotePortOversizePkts	1.3.6.1.4.1.8886.1.13.1.19.1.16	Counter32	read-only	The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
C32 raisecomRemotePortFragments	1.3.6.1.4.1.8886.1.13.1.19.1.17	Counter32	read-only	The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C32 raisecomRemotePortJabbers	1.3.6.1.4.1.8886.1.13.1.19.1.18	Counter32	read-only	The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a on-integral number of octets (Alignment Error).
C32 raisecomRemotePortCollisions	1.3.6.1.4.1.8886.1.13.1.19.1.19	Counter32	read-only	The best estimate of the total number of collisions on this Ethernet segment.
STR raisecomRemoteifName	1.3.6.1.4.1.8886.1.13.1.19.1.20	DisplayString	read-only	The textual name of the remote device interface.
C32 raisecomRemotePortifInMulticastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.21	Counter32	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.
C32 raisecomRemotePortifInBroadcastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.22	Counter32	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C32 raisecomRemotePortifOutMulticastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.23	Counter32	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C32 raisecomRemotePortifOutBroadcastPkts	1.3.6.1.4.1.8886.1.13.1.19.1.24	Counter32	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
INT raisecomRemotePortLinkUpDownTrapEnable	1.3.6.1.4.1.8886.1.13.1.19.1.25	INTEGER	read-write	Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disabled(2) otherwise.
G32 raisecomRemotePortHighSpeed	1.3.6.1.4.1.8886.1.13.1.19.1.26	Gauge32	read-only	An estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the interface is somewhere in the range of `n-500,000' to `n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero.
T/F raisecomRemotePortPromiscuousMode	1.3.6.1.4.1.8886.1.13.1.19.1.27	TruthValue	read-write	This object has a value of false(2) if this interface only accepts packets/frames that are addressed to this station. This object has a value of true(1) when the station accepts all packets/frames transmitted on the media. The value true(1) is only legal on certain types of media. If legal, setting this object to a value of true(1) may require the interface to be reset before becoming effective. The value of ifPromiscuousMode does not affect the reception of broadcast and multicast packets/frames by the interface.
T/F raisecomRemotePortConnectorPresent	1.3.6.1.4.1.8886.1.13.1.19.1.28	TruthValue	read-only	This object has the value 'true(1)' if the interface sublayer has a physical connector and the value 'false(2)' otherwise.
STR raisecomRemotePortAlias	1.3.6.1.4.1.8886.1.13.1.19.1.29	DisplayString	read-only	This object is an 'alias' name for the interface as specified by a network manager, and provides a non- volatile 'handle' for the interface.
TIM raisecomRemotePortCounterDiscontinuityTime	1.3.6.1.4.1.8886.1.13.1.19.1.30	TimeStamp	read-only	The value of sysUpTime on the most recent occasion at which any one or more of this interface's counters suffered a discontinuity. The relevant counters are the specific instances associated with this interface of any Counter32 or Counter64 object contained in the ifTable or ifXTable. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
INT raisecomRemoteVoltNormal	1.3.6.1.4.1.8886.1.13.1.20	INTEGER	read-only	This object specifies whether remote votage is in normal range or not.
INT raisecomRemoteMaxAllowedFrameLength	1.3.6.1.4.1.8886.1.13.1.21	INTEGER	read-write	This object specifies max ethernet frame length of remote device.
IP raisecomRemoteL3ObPortIpAddr	1.3.6.1.4.1.8886.1.13.1.22	IpAddress	read-write	The out IP Address of remote device.
IP raisecomRemoteL3ObPortMask	1.3.6.1.4.1.8886.1.13.1.23	IpAddress	read-write	The subnet mask for this remote subnet.
INT raisecomRemoteWorkMode	1.3.6.1.4.1.8886.1.13.1.24	INTEGER	read-write	This object specifies the work mode of the device.
ENA raisecomRemoteAlarmReportEnable	1.3.6.1.4.1.8886.1.13.1.25	EnableVar	read-write	Specifies whether or not the device reports all active alarms.
INT raisecomRemoteAutoUploadEnable	1.3.6.1.4.1.8886.1.13.1.26	INTEGER	read-write	The ifIndex value based 1 which identifies the unique interface of local device.
INT raisecomRemoteAutoUploadPeriod	1.3.6.1.4.1.8886.1.13.1.27	INTEGER	read-write	The ifIndex value based 1 which identifies the unique interface of local device.
raisecomRemoteifTable	1.3.6.1.4.1.8886.1.13.1.28		not-accessible	A list of remote device's interface entries. The number of entries is given by the value of ifNumber.
raisecomRemoteifEntry	1.3.6.1.4.1.8886.1.13.1.28.1		not-accessible	An entry containing management information applicable to a particular interface.
I32 raisecomRemotePortIndex	1.3.6.1.4.1.8886.1.13.1.28.1.1	Integer32	read-only	A unique value, greater than zero, for each interface.
STR raisecomRemoteifDescr	1.3.6.1.4.1.8886.1.13.1.28.1.2	DisplayString	read-only	A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
I32 raisecomRemoteifType	1.3.6.1.4.1.8886.1.13.1.28.1.3	Integer32	read-only	The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention.
I32 raisecomRemoteifMtu	1.3.6.1.4.1.8886.1.13.1.28.1.4	Integer32	read-only	The size of the largest packet which can be sent/received on the interface, specified in octets.
G32 raisecomRemoteifSpeed	1.3.6.1.4.1.8886.1.13.1.28.1.5	Gauge32	read-only	An estimate of the interface's current bandwidth in bits per second.
MAC raisecomRemoteifPhysAddress	1.3.6.1.4.1.8886.1.13.1.28.1.6	MacAddress	read-only	The interface's address at its protocol sub-layer.
INT raisecomRemoteifAdminStatus	1.3.6.1.4.1.8886.1.13.1.28.1.7	INTEGER	read-write	The desired state of the interface.
INT raisecomRemoteifOperStatus	1.3.6.1.4.1.8886.1.13.1.28.1.8	INTEGER	read-only	The current operational state of the interface.
TIK raisecomRemoteifLastChange	1.3.6.1.4.1.8886.1.13.1.28.1.9	TimeTicks	read-only	The value of sysUpTime at the time the interface entered its current operational state.
C32 raisecomRemoteifInOctets	1.3.6.1.4.1.8886.1.13.1.28.1.10	Counter32	read-only	The total number of octets received on the interface, including framing characters.
C32 raisecomRemoteifInUcastPkts	1.3.6.1.4.1.8886.1.13.1.28.1.11	Counter32	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.
C32 raisecomRemoteifInNUcastPkts	1.3.6.1.4.1.8886.1.13.1.28.1.12	Counter32	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer.
C32 raisecomRemoteifInDiscardsEx	1.3.6.1.4.1.8886.1.13.1.28.1.13	Counter32	read-only	The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.
C32 raisecomRemoteifInErrors	1.3.6.1.4.1.8886.1.13.1.28.1.14	Counter32	read-only	For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol.
C32 raisecomRemoteifInUnknownProtos	1.3.6.1.4.1.8886.1.13.1.28.1.15	Counter32	read-only	For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
C32 raisecomRemoteifOutOctets	1.3.6.1.4.1.8886.1.13.1.28.1.16	Counter32	read-only	The total number of octets transmitted out of the interface, including framing characters.
C32 raisecomRemoteifOutUcastPkts	1.3.6.1.4.1.8886.1.13.1.28.1.17	Counter32	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.
C32 raisecomRemoteifOutNUcastPkts	1.3.6.1.4.1.8886.1.13.1.28.1.18	Counter32	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.
C32 raisecomRemoteifOutDiscards	1.3.6.1.4.1.8886.1.13.1.28.1.19	Counter32	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
C32 raisecomRemoteifOutErrors	1.3.6.1.4.1.8886.1.13.1.28.1.20	Counter32	read-only	For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors.
G32 raisecomRemoteifOutQLen	1.3.6.1.4.1.8886.1.13.1.28.1.21	Gauge32	read-only	The length of the output packet queue (in packets).
OID raisecomRemoteifSpecific	1.3.6.1.4.1.8886.1.13.1.28.1.22	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular media being used to realize the interface.

RFC description

Monitors environmental conditions (temperature, voltage) on remote Raisecom devices for remote management.

Start monitoring RAISECOM TECH remotely-managed access equipment (EOC/PON remote unit telemetry) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RAISECOM-REMOTE-MANAGEMENT-REMOTE-MIB