All MIBs › QB-ATM-MIB
Organization: Quantum Bridge Inc.
Last Updated: 2001-01-02
Category: ATM, DSL and Broadband Access
Description: Manages Quantum Bridge ATM interface configuration, virtual circuit parameters, and traffic shaping on broadband access equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is QB-ATM-MIB?
This is a Quantum Bridge proprietary MIB that extends standard ATM management with additional objects for ATM interface configuration, virtual circuits, and traffic shaping on Quantum Bridge broadband access equipment. Its data spans ATM link/PNNI neighbor-peer topology and signaling counters, alongside configuration for virtual circuits and traffic parameters. It is used to monitor the operational software status of the ATM control plane — checking PNNI peer state (qbAtmPnniPeerState) and per-peer database summary and PTSE/PTSP message counters to confirm that PNNI neighbor relationships are stable and topology databases are synchronizing, which reveals routing/signaling instability if peer counts drop or message counters stall. It explicitly builds on the standard ATM MIB and related IETF ATM proposed drafts, adding Quantum Bridge-specific PNNI and switch-module extensions on top of that base. It is deployed on Quantum Bridge ATM broadband access/aggregation equipment in carrier networks using ATM/PNNI for circuit signaling and topology distribution, and network engineers typically reference the QB-ATM-MIB MIB when setting up PNNI-based monitoring for this equipment.
IPNetwork Monitor allows you to monitor SNMP objects defined in QB-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Quantum Bridge ATM broadband access switch
Monitoring Examples
An operator polls qbAtmPnniNbrPeerTable/qbAtmPnniNbrPeerEntry to see each PNNI neighbor (qbAtmPnniPeerRemoteNodeId) and its qbAtmPnniPeerState, confirming peers remain in a full/synchronized adjacency. Comparing qbAtmPnniPeerRcvDbSums/qbAtmPnniPeerXmtDbSums and the PTSP/PTSE request counters (qbAtmPnniPeerRcvPtsps/XmtPtsps, RcvPtseReqs/XmtPtseReqs) over time reveals whether topology-database exchange has stalled, which would explain routing instability across the ATM/PNNI mesh; qbAtmPnniPeerPortCount and qbAtmPnniPeerSvccRccIndex help correlate a peer relationship back to a specific physical port.
What Can Be Monitored
- PNNI neighbor peer state
- PNNI database summary counters
- PTSE/PTSP message counters
- peer port count/RCC index
This MIB depends on
Related MIBs
Imported Objects
From ATM-MIB
| atmInterfaceConfEntry | OBJECT-TYPE |
| atmTrafficDescrParamEntry | OBJECT-TYPE |
| atmVcCrossConnectEntry | OBJECT-TYPE |
| atmVclEntry | OBJECT-TYPE |
| atmVpCrossConnectEntry | OBJECT-TYPE |
| atmVplEntry | OBJECT-TYPE |
From ATM-TC-MIB
| AtmAddr | |
| AtmConnCastType | |
| AtmConnKind | |
| AtmServiceCategory | |
| AtmTrafficDescrParamIndex | |
| AtmVcIdentifier | |
| AtmVorXAdminStatus | |
| AtmVorXLastChange | |
| AtmVorXOperStatus | |
| AtmVpIdentifier | |
| atmNoClpNoScr | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero | |
| ifIndex | OBJECT-TYPE |
From QB-DWS-MIB
| QbEnableStatus | |
| QbPvcConnKind |
From QBSYS-SYSTEM-MIB
| TimeStamp |
From QUANTUMBRIDGE-REG
| qbMibs | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| qbAtmMIB | 1.3.6.1.4.1.4323.2.7 | This module defines additional objects for management of ATM links in Quantum Bridge devices, above and beyond what is defined in the standard ATM mib, and proposed drafts. | ||
| qbAtmObjects | 1.3.6.1.4.1.4323.2.7.1 | |||
| qbAtmInterfaceConfTable | 1.3.6.1.4.1.4323.2.7.1.1 | not-accessible | The Quantum Bridge ATM Interface Configuration Table contains extensions to the ATM Interface Configuration Table, one entry per ATM interface. | |
| qbAtmInterfaceConfEntry | 1.3.6.1.4.1.4323.2.7.1.1.1 | not-accessible | An entry in the Quantum ATM Interface Configuration Table. Every ATM interface contains a corresponding entry in the table. | |
| INT qbAtmInterfaceConfPolicingStatus | 1.3.6.1.4.1.4323.2.7.1.1.1.1 | INTEGER | read-write | If this object is set to 'enable' the policing is enabled on this interface. If the object set to 'disable,' the policing is disabled. Note: policing can be set on the S622 and 155 cards only. |
| INT qbAtmInterfaceConfMaxPvcVpi | 1.3.6.1.4.1.4323.2.7.1.1.1.2 | INTEGER | read-only | This object indicates the maximum value of VPI that can be used to create a VC on a given ATM native interface. |
| INT qbAtmInterfaceConfMinPvcVpi | 1.3.6.1.4.1.4323.2.7.1.1.1.3 | INTEGER | read-only | This object indicates the minimum value of VPI that can be used to create a VC on a given ATM native interface. |
| INT qbAtmInterfaceConfMaxPvcVci | 1.3.6.1.4.1.4323.2.7.1.1.1.4 | INTEGER | read-only | This object indicates the maximum value of VCI that can be used to create a VC on a given ATM native interface. |
| INT qbAtmInterfaceConfMinPvcVci | 1.3.6.1.4.1.4323.2.7.1.1.1.5 | INTEGER | read-only | This object indicates the minimum value of VCI that can be used to create a VC on a given ATM native interface. |
| INT qbAtmInterfaceConfMaxPvpVpi | 1.3.6.1.4.1.4323.2.7.1.1.1.6 | INTEGER | read-only | This object indicates the maximum value of VPI that can be used to create a VP on a given ATM native interface. |
| INT qbAtmInterfaceConfMinPvpVpi | 1.3.6.1.4.1.4323.2.7.1.1.1.7 | INTEGER | read-only | This object indicates the minimum value of VPI that can be used to create a VP on a given ATM native interface. |
| qbAtmTrafficDescrParamTable | 1.3.6.1.4.1.4323.2.7.1.2 | not-accessible | The Quantum Bridge ATM Traffic Descriptor Table contains extensions to the ATM Traffic Descriptor Table. | |
| qbAtmTrafficDescrParamEntry | 1.3.6.1.4.1.4323.2.7.1.2.1 | not-accessible | An entry in the Quantum Bridge ATM Traffic Descriptor Table. | |
| STR qbAtmTrafficDescrParamName | 1.3.6.1.4.1.4323.2.7.1.2.1.1 | DisplayString | read-create | A textual description of the traffic descriptor. |
| BOO qbAtmTrafficDescrParamDefault | 1.3.6.1.4.1.4323.2.7.1.2.1.2 | Boolean | read-only | The object indicates whether or not this is a default traffic descriptor. Traffic descriptor with indexes from 1 to 20 are default traffic descriptors and cannot be deleted. |
| qbAtmVclTable | 1.3.6.1.4.1.4323.2.7.1.3 | not-accessible | The Quantum Bridge Table contains an extension to the atmVclConnectTable, An entry in this table models VCLs. | |
| qbAtmVclEntry | 1.3.6.1.4.1.4323.2.7.1.3.1 | not-accessible | An entry in the QB ATM atmVclConnectTable. | |
| QBE qbAtmVclLoopback | 1.3.6.1.4.1.4323.2.7.1.3.1.1 | QbEnableStatus | read-write | Enable loopback on this ATM VCL |
| OCT qbAtmVclF4F5LoopbackInsert | 1.3.6.1.4.1.4323.2.7.1.3.1.2 | OCTET STRING | read-write | This is a loopback Insert object for LLID. Start loopback Insert by setting this to an LLID value. |
| QBF qbAtmVclF4F5LoopbackStatus | 1.3.6.1.4.1.4323.2.7.1.3.1.3 | QbF4F5LoopbackStatus | read-only | Status of loopback Insert command: in-progress, success, timeout. |
| TIM qbAtmVclF4F5LoopbackTimestamp | 1.3.6.1.4.1.4323.2.7.1.3.1.4 | TimeStamp | read-only | Value of sysUptime when last Insert completed. |
| IP qbAtmVclMgmtIpAddr | 1.3.6.1.4.1.4323.2.7.1.3.1.5 | IpAddress | read-write | Active IP Address for in-band Management SNMP of this chassis. |
| IP qbAtmVclMgmtIpMask | 1.3.6.1.4.1.4323.2.7.1.3.1.6 | IpAddress | read-write | This is the IP network mask associated with the in-band Management interface. |
| IP qbAtmVclMgmtNeighborIP | 1.3.6.1.4.1.4323.2.7.1.3.1.7 | IpAddress | read-write | This is the neighbor IP address associated with the in-band Management interface. |
| QBP qbAtmVclConnKind | 1.3.6.1.4.1.4323.2.7.1.3.1.8 | QbPvcConnKind | read-only | The VCL connection type. |
| QBF qbAtmVclF4F5TxStatus | 1.3.6.1.4.1.4323.2.7.1.3.1.9 | QbF4F5Status | read-only | The transmitted OAM status for the PVC. |
| TIM qbAtmVclF4F5TxLastChange | 1.3.6.1.4.1.4323.2.7.1.3.1.10 | TimeStamp | read-only | The value of sysUPtime when qbAtmVclF4F5TxStatus last changed. |
| QBF qbAtmVclF4F5RxStatus | 1.3.6.1.4.1.4323.2.7.1.3.1.11 | QbF4F5Status | read-only | The received OAM status of the PVC. |
| TIM qbAtmVclF4F5RxLastChange | 1.3.6.1.4.1.4323.2.7.1.3.1.12 | TimeStamp | read-only | The value of sysUPtime when qbAtmVclF4F5TxStatus last changed. |
| qbAtmVplTable | 1.3.6.1.4.1.4323.2.7.1.4 | not-accessible | The Quantum Bridge Table contains an extension to the atmVclConnectTable, An entry in this table models VPLs. | |
| qbAtmVplEntry | 1.3.6.1.4.1.4323.2.7.1.4.1 | not-accessible | An entry in the QB ATM qbAtmVpTable. | |
| QBE qbAtmVplLoopback | 1.3.6.1.4.1.4323.2.7.1.4.1.1 | QbEnableStatus | read-write | Enable loopback on this ATM VPL |
| OCT qbAtmVplF4F5LoopbackInsert | 1.3.6.1.4.1.4323.2.7.1.4.1.2 | OCTET STRING | read-write | This is a loopback Insert object for LLID. Start loopback Insert by setting this to an LLID value. |
| QBF qbAtmVplF4F5LoopbackStatus | 1.3.6.1.4.1.4323.2.7.1.4.1.3 | QbF4F5LoopbackStatus | read-only | Status of loopback Insert command: in-progress, success, timeout. |
| TIM qbAtmVplF4F5LoopbackTimestamp | 1.3.6.1.4.1.4323.2.7.1.4.1.4 | TimeStamp | read-only | Value of sysUptime when last Insert completed. |
| QBF qbAtmVplF4F5TxStatus | 1.3.6.1.4.1.4323.2.7.1.4.1.5 | QbF4F5Status | read-only | The transmitted OAM status for the PVP. |
| TIM qbAtmVplF4F5TxLastChange | 1.3.6.1.4.1.4323.2.7.1.4.1.6 | TimeStamp | read-only | The value of sysUPtime when qbAtmVclF4F5TxStatus last changed. |
| QBF qbAtmVplF4F5RxStatus | 1.3.6.1.4.1.4323.2.7.1.4.1.7 | QbF4F5Status | read-only | The received OAM status of the PVP. |
| TIM qbAtmVplF4F5RxLastChange | 1.3.6.1.4.1.4323.2.7.1.4.1.8 | TimeStamp | read-only | The value of sysUPtime when qbAtmVclF4F5TxStatus last changed. |
| qbAtmVcCrossConnectTable | 1.3.6.1.4.1.4323.2.7.1.5 | not-accessible | The Quantum Bridge Table contains an extension to the atmVcCrossConnectTable, An entry in this table models two cross-connected VCLs. | |
| qbAtmVcCrossConnectEntry | 1.3.6.1.4.1.4323.2.7.1.5.1 | not-accessible | An entry in the QB ATM atmVcCrossConnectTable. | |
| STR qbAtmVcCrossConnectName | 1.3.6.1.4.1.4323.2.7.1.5.1.1 | DisplayString | read-create | A textual description for the cross connect. |
| ATM qbAtmVcCrossConnectRxTrafficDescrIndex | 1.3.6.1.4.1.4323.2.7.1.5.1.2 | AtmTrafficDescrParamIndex | read-create | The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCLs cross-connect. |
| ATM qbAtmVcCrossConnectTxTrafficDescrIndex | 1.3.6.1.4.1.4323.2.7.1.5.1.3 | AtmTrafficDescrParamIndex | read-create | The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCLs cross-connect |
| qbAtmVpCrossConnectTable | 1.3.6.1.4.1.4323.2.7.1.6 | not-accessible | The Quantum Bridge Table contains an extension to the atmVpCrossConnectTable, An entry in this table models two cross-connected VPLs. | |
| qbAtmVpCrossConnectEntry | 1.3.6.1.4.1.4323.2.7.1.6.1 | not-accessible | An entry in the QB ATM atmVpCrossConnectTable. | |
| STR qbAtmVpCrossConnectName | 1.3.6.1.4.1.4323.2.7.1.6.1.1 | DisplayString | read-create | A textual description for the cross connect. |
| ATM qbAtmVpCrossConnectRxTrafficDescrIndex | 1.3.6.1.4.1.4323.2.7.1.6.1.2 | AtmTrafficDescrParamIndex | read-create | The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VPLs cross-connect. |
| ATM qbAtmVpCrossConnectTxTrafficDescrIndex | 1.3.6.1.4.1.4323.2.7.1.6.1.3 | AtmTrafficDescrParamIndex | read-create | The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VPLs cross-connect |
| qbAtmSigGroup | 1.3.6.1.4.1.4323.2.7.1.7 | |||
| qbAtmPnniNodeTable | 1.3.6.1.4.1.4323.2.7.1.7.1 | not-accessible | The QbAtmpnniNodeTable contains attributes that affect the operation of a PNNI logical node. There is a single row in this table for each PNNI peer group that the managed system is expected or eligible to become a member of. | |
| qbAtmPnniNodeEntry | 1.3.6.1.4.1.4323.2.7.1.7.1.1 | not-accessible | An entry in the table, containing information about a PNNI logical node in this switching system. | |
| INT qbAtmPnniNodeIndex | 1.3.6.1.4.1.4323.2.7.1.7.1.1.1 | INTEGER | not-accessible | A value assigned to a node in this switching system that uniquely identifies it in the MIB. |
| OCT qbAtmPnniNodeNetAddrPrefix | 1.3.6.1.4.1.4323.2.7.1.7.1.1.2 | OCTET STRING | read-create | Indicates the Network Prefix to use for the ATM End System Address. The value is 13 bytes long, and is specified in the hexadecimal format. If less than 13 bytes(26 chars) are received, the agent appends trailing zero's. The object can be set to ''h, if PNNI protocol is desirable on all interfaces. |
| OCT qbAtmPnniNodeEndSysId | 1.3.6.1.4.1.4323.2.7.1.7.1.1.3 | OCTET STRING | read-create | Indicates the End System Identifier for ATM End System Address. The value is 7 bytes long, and is specified in the hexadecimal format. The object can be set to ''h, if PNNI protocol is desirable on all interfaces. |
| INT qbAtmPnniNodeLevel | 1.3.6.1.4.1.4323.2.7.1.7.1.1.4 | INTEGER | read-create | The level of PNNI hierarchy at which this node exists. This attribute is used to determine the default node ID and the default peer group ID for this node. This object may only be written when pnniNodeAdminStatus has the value down. |
| ROW qbAtmPnniNodeRowStatus | 1.3.6.1.4.1.4323.2.7.1.7.1.1.5 | RowStatus | read-create | To create, delete, activate and de-activate a Node. Setting this object to createAndGo(4) causes the corresponding row to be created. Setting this object to destroy(6) causes the corresponding row to be deleted. Note that -- currently-- only a single instance of a row can be created in this table. |
| INT qbAtmPnniNodeOperStatus | 1.3.6.1.4.1.4323.2.7.1.7.1.1.6 | INTEGER | read-only | Indicates the Operational Status of the PNNI Node. For Logical Group Nodes, the Operational Status will be up only if the child becomes the PGL. |
| QBA qbAtmPnniNodeAtmAddress | 1.3.6.1.4.1.4323.2.7.1.7.1.1.7 | QbAtmPnniAtmAddr | read-only | This node's ATM End System Address. Remote systems wishing to exchange PNNI protocol packets with this node should direct packets or calls to this address. The current Qb implementation does not support writing this value. |
| QBA qbAtmPnniNodePeerGroupId | 1.3.6.1.4.1.4323.2.7.1.7.1.1.8 | QbAtmPnniPeerGroupId | read-only | The Peer Group Identifier of the peer group that the given node is to become a member of. |
| qbAtmPnniIfTable | 1.3.6.1.4.1.4323.2.7.1.7.2 | not-accessible | The qbAtmPnniIfTable contains the attributes necessary to configure a physical interface on a switching system capable of being used for PNNI routing. An ifIndex is used as the instance ID to uniquely identify the interface on the local switching system. This index has the same value as the ifIndex object defined in RFC 1573 for the same interface, since this table correlates with the ifTable in RFC 1573. One row in this table is created by the managed system for each row in the ifTable that has an ifType of atm(37) or atmLogical(80). | |
| qbAtmPnniIfEntry | 1.3.6.1.4.1.4323.2.7.1.7.2.1 | not-accessible | An entry in the table, containing PNNI specific interface information in this switching system. | |
| INT qbAtmPnniIfNodeIndex | 1.3.6.1.4.1.4323.2.7.1.7.2.1.1 | INTEGER | read-write | Identifies the node within the switching system that the interface is directly attached to. Note: For this release this value can be set only to 1. |
| QBA qbAtmPnniIfAdmWeightCbr | 1.3.6.1.4.1.4323.2.7.1.7.2.1.2 | QbAtmPnniWeight | read-write | The administrative weight of this interface for the constant bit rate service category. |
| QBA qbAtmPnniIfAdmWeightRtVbr | 1.3.6.1.4.1.4323.2.7.1.7.2.1.3 | QbAtmPnniWeight | read-write | The administrative weight of this interface for the real-time variable bit rate service category. |
| QBA qbAtmPnniIfAdmWeightNrtVbr | 1.3.6.1.4.1.4323.2.7.1.7.2.1.4 | QbAtmPnniWeight | read-write | The administrative weight of this interface for the non-real-time variable bit rate service category. |
| QBA qbAtmPnniIfAdmWeightAbr | 1.3.6.1.4.1.4323.2.7.1.7.2.1.5 | QbAtmPnniWeight | read-write | The administrative weight of this interface for the available bit rate service category. |
| QBA qbAtmPnniIfAdmWeightUbr | 1.3.6.1.4.1.4323.2.7.1.7.2.1.6 | QbAtmPnniWeight | read-write | The administrative weight of this interface for the unspecified bit rate service category. |
| ATM qbAtmPnniIfRccServiceCategory | 1.3.6.1.4.1.4323.2.7.1.7.2.1.7 | AtmServiceCategory | read-write | The service category used for the PNNI routing control channel (VCI=18) on this interface. |
| ATM qbAtmPnniIfRccTrafficDescrIndex | 1.3.6.1.4.1.4323.2.7.1.7.2.1.8 | AtmTrafficDescrParamIndex | read-write | The traffic descriptor index referring to the entry in the atmTrafficDescrParamTable defined in RFC 1695 that specifies the traffic allocation for the PNNI routing control channel (VCI=18) on this interface. |
| INT qbAtmPnniIfPolicingStatus | 1.3.6.1.4.1.4323.2.7.1.7.2.1.9 | INTEGER | read-write | If this object is set to enable, the policing is enabled on this interface. If the object is set to 'disable' the policing is disabled. |
| qbAtmPnniRouteAddrTable | 1.3.6.1.4.1.4323.2.7.1.7.3 | not-accessible | A table containing all the attributes necessary to determine what the PNNI entity believes is reachable in terms of ATM End System Addresses, and to determine which nodes are advertising this reachability. This table is also used to configure static routes to reachable address prefixes. The local node index that receives the reachability information, reachable address, address prefix length, and an index that distinguishes between multiple listings of connectivity to a given address prefix from a given local node are combined to form an instance ID for this object. | |
| qbAtmPnniRouteAddrEntry | 1.3.6.1.4.1.4323.2.7.1.7.3.1 | not-accessible | An entry in the table, containing information about a reachable address prefix. | |
| NUM qbAtmPnniRouteAddrIfIndex | 1.3.6.1.4.1.4323.2.7.1.7.3.1.1 | InterfaceIndex | not-accessible | The local interface over which the reachable address can be reached. |
| OCT qbAtmPnniRouteAddrAddress | 1.3.6.1.4.1.4323.2.7.1.7.3.1.2 | OCTET STRING | not-accessible | The value of the ATM End System Address prefix. |
| INT qbAtmPnniRouteAddrPrefixLength | 1.3.6.1.4.1.4323.2.7.1.7.3.1.3 | INTEGER | read-create | Indicates the number of bits to be applied to the ATM End System Address prefix. |
| ROW qbAtmPnniRouteAddrRowStatus | 1.3.6.1.4.1.4323.2.7.1.7.3.1.4 | RowStatus | read-create | To create, delete, activate and de-activate a reachable address prefix. |
| INT qbAtmPnniRouteAddrProto | 1.3.6.1.4.1.4323.2.7.1.7.3.1.5 | INTEGER | read-only | This object indicates the Routing mechanism through which the connectivity from the advertising node to the reachable address prefix was learned. |
| qbAtmInterfaceConfSigTable | 1.3.6.1.4.1.4323.2.7.1.7.4 | not-accessible | This table contains ATM local interface configuration parameters, one entry per ATM interface port. | |
| qbAtmInterfaceConfSigEntry | 1.3.6.1.4.1.4323.2.7.1.7.4.1 | not-accessible | This list contains additonal ATM interface configuration parameters and state variables. | |
| QBA qbAtmInterfaceConfSigMode | 1.3.6.1.4.1.4323.2.7.1.7.4.1.1 | QbAtmSigSpec | read-write | The type of ATM interface which is either a UNI (User to Network), PNNI or IISP. To modify the qbAtmInterfaceConfSignType, ifAdminStatus has to be down. |
| INT qbAtmInterfaceConfSigSide | 1.3.6.1.4.1.4323.2.7.1.7.4.1.2 | INTEGER | read-write | The side of ATM interface which is either a user or network side. NotApplicable value implies that qbAtmInterfaceConfSignType is other than uni or iisp. |
| INT qbAtmInterfaceConfSigParseMode | 1.3.6.1.4.1.4323.2.7.1.7.4.1.3 | INTEGER | read-write | Indicates to the signalling stack to use strict parsing of the INformation Elements (IEs) within signalling messages. This parameter is set to 'on' for conformance testing. For systems that do not test conformance it is recommended to set the object to 'off'. |
| INT qbAtmInterfaceConfSigAdminStatus | 1.3.6.1.4.1.4323.2.7.1.7.4.1.4 | INTEGER | read-write | Enable/Disable signalling/sscop on this interface. To modify the qbAtmInterfaceConfSignAdminStatus, ifAdminStatus has to be down. |
| INT qbAtmInterfaceConfSigSvcMinVci | 1.3.6.1.4.1.4323.2.7.1.7.4.1.5 | INTEGER | read-write | The minimum value of SVC connection for vci. |
| INT qbAtmInterfaceConfSigSvcMaxVci | 1.3.6.1.4.1.4323.2.7.1.7.4.1.6 | INTEGER | read-write | The maximum value of SVC connection for vci. |
| INT qbAtmInterfaceConfSigSvcMinVpi | 1.3.6.1.4.1.4323.2.7.1.7.4.1.7 | INTEGER | read-write | The minimum value of SVC connection for vpi. |
| INT qbAtmInterfaceConfSigSvcMaxVpi | 1.3.6.1.4.1.4323.2.7.1.7.4.1.8 | INTEGER | read-write | The maximum value of SVC connection for vpi. |
| INT qbAtmInterfaceConfSigSvpMinVpi | 1.3.6.1.4.1.4323.2.7.1.7.4.1.9 | INTEGER | read-write | The minimum value of SVP connection for vpi. |
| INT qbAtmInterfaceConfSigSvpMaxVpi | 1.3.6.1.4.1.4323.2.7.1.7.4.1.10 | INTEGER | read-write | The maximum value of SVP connection for vpi. |
| ATM qbAtmInterfaceConfSigLastChange | 1.3.6.1.4.1.4323.2.7.1.7.4.1.11 | AtmVorXLastChange | read-only | The value of sysUpTime at the time this interface changed its current administrative state. |
| BOO qbAtmInterfaceConfSigIlmiEnable | 1.3.6.1.4.1.4323.2.7.1.7.4.1.12 | Boolean | read-write | Can be enabled only if signaling is configured. ILMI is enabled by default when signaling is configured on the system and the user may enter the disable option . |
| qbAtmPnniNbrPeerTable | 1.3.6.1.4.1.4323.2.7.1.7.5 | not-accessible | The qbAtmPnniNbrPeer Object contains all the attributes necessary to describe the relationship a node in this switching system has with a neighboring node within the same peer group. A concatenation of the Node Identifier of the node within the local switching system and the neighboring peer's Node Identifier is used to form the instance ID for this object. The entire qbAtmPnniNbrPeer object is read-only, reflecting the fact that neighboring peers are discovered dynamically by the PNNI protocol rather than configured. | |
| qbAtmPnniNbrPeerEntry | 1.3.6.1.4.1.4323.2.7.1.7.5.1 | not-accessible | An entry in the table, containing information about this node's relationship with a neighboring peer node. | |
| QBA qbAtmPnniPeerRemoteNodeId | 1.3.6.1.4.1.4323.2.7.1.7.5.1.1 | QbAtmPnniNodeId | not-accessible | The Node Identifier of the neighboring peer node. |
| INT qbAtmPnniPeerState | 1.3.6.1.4.1.4323.2.7.1.7.5.1.2 | INTEGER | read-only | Indicates the state of this node's Neighboring Peer State Machine associated with qbAtmPnniPeerRemoteNodeId. |
| INT qbAtmPnniPeerSvccRccIndex | 1.3.6.1.4.1.4323.2.7.1.7.5.1.3 | INTEGER | read-only | Identifies the SVCC-based RCC being used to communicate with the neighboring peer if one exists. If both the local node and the neighboring peer node are lowest-level nodes, this attribute is set to zero. |
| INT qbAtmPnniPeerPortCount | 1.3.6.1.4.1.4323.2.7.1.7.5.1.4 | INTEGER | read-only | A count of the total number of ports that connect to the neighboring peer. If the neighboring peer only communicates via an SVCC-based RCC, the value of this attribute is set to zero. Otherwise it is set to the total number of ports to the neighboring peer in the Hello state 2-WayInside. |
| C32 qbAtmPnniPeerRcvDbSums | 1.3.6.1.4.1.4323.2.7.1.7.5.1.5 | Counter32 | read-only | A count of the number of Database Summary Packets received from the neighboring peer. |
| C32 qbAtmPnniPeerXmtDbSums | 1.3.6.1.4.1.4323.2.7.1.7.5.1.6 | Counter32 | read-only | A count of the number of Database Summary Packets transmitted to the neighboring peer. |
| C32 qbAtmPnniPeerRcvPtsps | 1.3.6.1.4.1.4323.2.7.1.7.5.1.7 | Counter32 | read-only | A count of the number of PTSPs received from the neighboring peer. |
| C32 qbAtmPnniPeerXmtPtsps | 1.3.6.1.4.1.4323.2.7.1.7.5.1.8 | Counter32 | read-only | A count of the number of PTSPs (re)transmitted to the neighboring peer. |
| C32 qbAtmPnniPeerRcvPtseReqs | 1.3.6.1.4.1.4323.2.7.1.7.5.1.9 | Counter32 | read-only | A count of the number of PTSE Request packets received from the neighboring peer. |
| C32 qbAtmPnniPeerXmtPtseReqs | 1.3.6.1.4.1.4323.2.7.1.7.5.1.10 | Counter32 | read-only | A count of the number of PTSE Request packets transmitted to the neighboring peer. |
| C32 qbAtmPnniPeerRcvPtseAcks | 1.3.6.1.4.1.4323.2.7.1.7.5.1.11 | Counter32 | read-only | A count of the number of PTSE Ack packets received from the neighboring peer. |
| C32 qbAtmPnniPeerXmtPtseAcks | 1.3.6.1.4.1.4323.2.7.1.7.5.1.12 | Counter32 | read-only | A count of the number of PTSE Ack packets transmitted to the neighboring peer. |
| qbAtmPnniNodePglTable | 1.3.6.1.4.1.4323.2.7.1.7.6 | not-accessible | Peer group leader election information for a PNNI node in this switching system. | |
| qbAtmPnniNodePglEntry | 1.3.6.1.4.1.4323.2.7.1.7.6.1 | not-accessible | An entry in the table, containing PGL election information of a PNNI logical node in this switching system. | |
| INT qbAtmPnniNodePglLeadershipPriority | 1.3.6.1.4.1.4323.2.7.1.7.6.1.1 | INTEGER | read-create | The Leadership priority value this node should advertise in its nodal information group for the given peer group. Only the value zero can be used with nodes that are not PGL/LGN capable. If there is no configured parent node index or no corresponding entry in the pnniNodeTable, then the advertised leadership priority is zero regardless of this value. |
| I32 qbAtmPnniNodeCfgParentNodeIndex | 1.3.6.1.4.1.4323.2.7.1.7.6.1.2 | Integer32 | read-create | The local node index used to identify the node that will represent this peer group at the next higher level of hierarchy, if this node becomes peer group leader. The value 0 indicates that there is no parent node. |
| I32 qbAtmPnniNodePglInitTime | 1.3.6.1.4.1.4323.2.7.1.7.6.1.3 | Integer32 | read-create | The amount of time in seconds this node will delay advertising its choice of preferred PGL after having initialized operation and reached the full state with at least one neighbor in the peer group. |
| I32 qbAtmPnniNodePglOverrideDelay | 1.3.6.1.4.1.4323.2.7.1.7.6.1.4 | Integer32 | read-create | The amount of time in seconds a node will wait for itself to be declared the preferred PGL by unanimous agreement among its peers. In the absence of unanimous agreement this will be the amount of time that will pass before this node considers a two thirds majority as sufficient agreement to declare itself peer group leader, abandoning the attempt to get unanimous agreement. |
| I32 qbAtmPnniNodePglReelectTime | 1.3.6.1.4.1.4323.2.7.1.7.6.1.5 | Integer32 | read-create | The amount of time in seconds after losing connectivity to the current peer group leader, that this node will wait before re-starting the process of electing a new peer group leader. |
| INT qbAtmPnniNodePglState | 1.3.6.1.4.1.4323.2.7.1.7.6.1.6 | INTEGER | read-only | Indicates the state that this node is in with respect to the Peer Group Leader election that takes place in the node's peer group. The values are enumerated in the Peer Group Leader State Machine. |
| QBA qbAtmPnniNodePreferredPgl | 1.3.6.1.4.1.4323.2.7.1.7.6.1.7 | QbAtmPnniNodeId | read-only | The Node ID of the node which the local node believes should be or become the peer group leader. This is also the value the local node is currently advertising in the `Preferred Peer Group Leader Node ID' field of its nodal information group within the given peer group. If a Preferred PGL has not been chosen, this attribute's value is set to (all) zero(s). |
| QBA qbAtmPnniNodePeerGroupLeader | 1.3.6.1.4.1.4323.2.7.1.7.6.1.8 | QbAtmPnniNodeId | read-only | The Node Identifier of the node which is currently operating as peer group leader of the peer group this node belongs to. If a PGL has not been elected, this attribute's value is set to (all) zero(s). |
| TIM qbAtmPnniNodePglTimeStamp | 1.3.6.1.4.1.4323.2.7.1.7.6.1.9 | TimeStamp | read-only | The time at which the current Peer Group Leader established itself. |
| QBA qbAtmPnniNodeActiveParentNodeId | 1.3.6.1.4.1.4323.2.7.1.7.6.1.10 | QbAtmPnniNodeId | read-only | The Node Identifier value being used by the Peer Group Leader to represent this peer group at the next higher level of the hierarchy. If this node is at the highest level of the hierarchy or if no PGL has yet been elected the PNNI Protocol Entity sets the value of this attribute to (all) zero(s). |
| qbAtmPnniNodeTimerTable | 1.3.6.1.4.1.4323.2.7.1.7.7 | not-accessible | A table of initial PNNI timer values and significant change thresholds. | |
| qbAtmPnniNodeTimerEntry | 1.3.6.1.4.1.4323.2.7.1.7.7.1 | not-accessible | An entry in the table, containing initial PNNI timer values and significant change thresholds of a PNNI logical node in this switching system. | |
| I32 qbAtmPnniNodePtseHolddown | 1.3.6.1.4.1.4323.2.7.1.7.7.1.1 | Integer32 | read-create | The initial value for the PTSE hold down timer that will be used by the given node to limit the rate at which it can re-originate PTSEs. It must be a positive non-zero number. |
| I32 qbAtmPnniNodeHelloHolddown | 1.3.6.1.4.1.4323.2.7.1.7.7.1.2 | Integer32 | read-create | The initial value for the Hello hold down timer that will be used by the given node to limit the rate at which it sends Hellos. It must be a positive non-zero number. |
| I32 qbAtmPnniNodeHelloInterval | 1.3.6.1.4.1.4323.2.7.1.7.7.1.3 | Integer32 | read-create | The initial value for the Hello Timer. In the absence of triggered Hellos, this node will send one Hello packet on each of its ports on this interval. |
| I32 qbAtmPnniNodeHelloInactivityFactor | 1.3.6.1.4.1.4323.2.7.1.7.7.1.4 | Integer32 | read-create | The value for the Hello Inactivity factor that this node will use to determine when a neighbor has gone down. |
| I32 qbAtmPnniNodeHlinkInact | 1.3.6.1.4.1.4323.2.7.1.7.7.1.5 | Integer32 | read-create | The amount of time a node will continue to advertise a horizontal (logical) link for which it has not received and processed a LGN Horizontal Link information group. |
| I32 qbAtmPnniNodePtseRefreshInterval | 1.3.6.1.4.1.4323.2.7.1.7.7.1.6 | Integer32 | read-create | The initial value for the Refresh timer that this node will use to drive (re-)origination of PTSEs in the absence of triggered updates. |
| INT qbAtmPnniNodePtseLifetimeFactor | 1.3.6.1.4.1.4323.2.7.1.7.7.1.7 | INTEGER | read-create | The value for the lifetime multiplier, expressed as a percentage. The result of multiplying the qbAtmPnniNodePtseRefreshInterval attribute value by this attribute value is used as the initial lifetime that this node places into self-originated PTSEs. |
| I32 qbAtmPnniNodeRxmtInterval | 1.3.6.1.4.1.4323.2.7.1.7.7.1.8 | Integer32 | read-create | The period between retransmissions of unacknowledged Database Summary packets, PTSE Request packets, and PTSPs. |
| I32 qbAtmPnniNodePeerDelayedAckInterval | 1.3.6.1.4.1.4323.2.7.1.7.7.1.9 | Integer32 | read-create | The minimum amount of time between transmissions of delayed PTSE acknowledgement packets. |
| INT qbAtmPnniNodeAvcrPm | 1.3.6.1.4.1.4323.2.7.1.7.7.1.10 | INTEGER | read-create | The proportional multiplier used in the algorithms that determine significant change for AvCR parameters, expressed as a percentage. |
| INT qbAtmPnniNodeAvcrMt | 1.3.6.1.4.1.4323.2.7.1.7.7.1.11 | INTEGER | read-create | The minimum threshold used in the algorithms that determine significant change for AvCR parameters, expressed as a percentage. |
| INT qbAtmPnniNodeCdvPm | 1.3.6.1.4.1.4323.2.7.1.7.7.1.12 | INTEGER | read-create | The proportional multiplier used in the algorithms that determine significant change for CDV metrics, expressed as a percentage. |
| INT qbAtmPnniNodeCtdPm | 1.3.6.1.4.1.4323.2.7.1.7.7.1.13 | INTEGER | read-create | The proportional multiplier used in the algorithms that determine significant change for CTD metrics, expressed as a percentage. |
| qbAtmPnniLinkTable | 1.3.6.1.4.1.4323.2.7.1.7.8 | not-accessible | This table contains the attributes necessary to describe the operation of logical links attached to the local switching system and the relationship with the neighbor nodes on the other end of the links. Links are attached to a specific node within the switching system. A concatenation of the Node Index of the node within the local switching system and the port ID are used as the instance ID to uniquely identify the link. Links may represent horizontal links between lowest level neighboring peers, outside links, uplinks, or horizontal links to/from LGNs. The entire qbAtmPnniLink object is read-only, reflecting the fact that this information is discovered dynamically by the PNNI protocol rather than configured. | |
| qbAtmPnniLinkEntry | 1.3.6.1.4.1.4323.2.7.1.7.8.1 | not-accessible | An entry in the table, containing information about a link attached to a PNNI logical node in this switching system. | |
| I32 qbAtmPnniLinkPortId | 1.3.6.1.4.1.4323.2.7.1.7.8.1.1 | Integer32 | not-accessible | The Port Identifier of the link as selected by the local node. This value has meaning only within the context of the node to which the port is attached. |
| INT qbAtmPnniLinkType | 1.3.6.1.4.1.4323.2.7.1.7.8.1.2 | INTEGER | read-only | Indicates the type of link being described. |
| QBA qbAtmPnniLinkHelloState | 1.3.6.1.4.1.4323.2.7.1.7.8.1.3 | QbAtmPnniHelloState | read-only | For horizontal and outside links between lowest-level nodes and for links of unknown type, this attribute indicates the state of the Hello protocol exchange over this link. For links to/from LGNs, this attribute indicates the state of the corresponding LGN Horizontal Link Hello State Machine. For uplinks (where the port ID is not also used for the underlying outside link), this attribute is set to notApplicable. |
| qbAtmHiddenVclTable | 1.3.6.1.4.1.4323.2.7.1.8 | not-accessible | The QB table with extensions to atmVclTable | |
| qbAtmHiddenVclEntry | 1.3.6.1.4.1.4323.2.7.1.8.1 | not-accessible | Entry in qbAtmHiddenVclTable | |
| STR qbAtmHiddenVclName | 1.3.6.1.4.1.4323.2.7.1.8.1.1 | DisplayString | read-create | A textual description for the SPVC name. |
| INT qbAtmHiddenVclType | 1.3.6.1.4.1.4323.2.7.1.8.1.2 | INTEGER | read-create | Value for the interface type. Native ATM - Q155, S622; non-native - E1, DS1, ENET, VT |
| NUM qbAtmHiddenVclIfIndex | 1.3.6.1.4.1.4323.2.7.1.8.1.3 | InterfaceIndex | read-create | ifIndex value for IOT interface. This value is not used for native ATM interfaces. |
| INT qbAtmHiddenVclVtIndex | 1.3.6.1.4.1.4323.2.7.1.8.1.4 | INTEGER | read-create | Address information for a VT card. This value is used for VT cards only. |
| qbAtmSwitchModuleGroup | 1.3.6.1.4.1.4323.2.7.1.9 | |||
| C32 qbAtmStatsBuffOverCells | 1.3.6.1.4.1.4323.2.7.1.9.1 | Counter32 | read-only | This object gives the number of cells discarded due to buffer overflows. |
| C32 qbAtmStatsInvalidCells | 1.3.6.1.4.1.4323.2.7.1.9.2 | Counter32 | read-only | This object gives the number of cells discarded due to unknown VPI/VCI. |
| C32 qbAtmStatsInvUpdateCells | 1.3.6.1.4.1.4323.2.7.1.9.3 | Counter32 | read-only | This object gives the number of cells discarded due to internal switch errors. |
| qbAtmInterfaceStatTable | 1.3.6.1.4.1.4323.2.7.1.10 | not-accessible | The Quantum Bridge ATM Interface Statistic Table contains ATM layer statistics for each ATM interface. | |
| qbAtmInterfaceStatEntry | 1.3.6.1.4.1.4323.2.7.1.10.1 | not-accessible | An entry in the Quantum ATM Interface Table. Every ATM interface contains a corresponding entry in the table. | |
| C32 qbAtmInterfaceStatTxOAMCells | 1.3.6.1.4.1.4323.2.7.1.10.1.1 | Counter32 | read-only | The total number of valid OAM cells transmitted by this atm layer interface. |
| C32 qbAtmInterfaceStatRxOAMCells | 1.3.6.1.4.1.4323.2.7.1.10.1.2 | Counter32 | read-only | The total number of OAS ATM cells received by this atm layer interface. |
| qbAtmInBandMgtTable | 1.3.6.1.4.1.4323.2.7.1.11 | not-accessible | The QbAtmInBandMgtTable defines in-band Management IP channels for use by ATM connections. | |
| qbAtmInBandMgtEntry | 1.3.6.1.4.1.4323.2.7.1.11.1 | not-accessible | An entry in the table, containing information about an in-band Management channel. | |
| IP qbAtmInBandMgtIpAddr | 1.3.6.1.4.1.4323.2.7.1.11.1.1 | IpAddress | not-accessible | An IP Address for in-band SNMP Management of this chassis. |
| IP qbAtmInBandMgtIpMask | 1.3.6.1.4.1.4323.2.7.1.11.1.2 | IpAddress | read-create | The IP Network Mask associated with this in-band SNMP Management IP Address. |
| NUM qbAtmInBandMgtIpIfIndex | 1.3.6.1.4.1.4323.2.7.1.11.1.3 | InterfaceIndex | read-create | The Interface associated with this in-band management address. |
| IP qbAtmInBandMgtNeighborIp | 1.3.6.1.4.1.4323.2.7.1.11.1.4 | IpAddress | read-create | This is the neighbor IP address associated with the in-band Management Interface. If the qbAtmInBandMgtConnKind is any value other than pvc(1), this object is non-applicable. |
| NUM qbAtmInBandMgtIfIndex | 1.3.6.1.4.1.4323.2.7.1.11.1.5 | InterfaceIndex | read-create | This is the interface index associated with the in-band Management connection. If the qbAtmInBandMgtConnKind is any value other than pvc(1), this object is non-applicable. |
| OID qbAtmInBandMgtVpi | 1.3.6.1.4.1.4323.2.7.1.11.1.6 | AtmVpIdentifier | read-create | If the value of qbAtmInBandMgtConnKind is pvc(1), this is the VPI associated with this in-band management connection. If the value of qbAtmInBandMgtConnKind is spvcInitiator(4), this object is target VPI. In all other cases, the value of this object is non-applicable. |
| OID qbAtmInBandMgtVci | 1.3.6.1.4.1.4323.2.7.1.11.1.7 | AtmVcIdentifier | read-create | If the value of qbAtmInBandMgtConnKind is pvc(1), this is the VCI associated with this in-band management connection. If the value of qbAtmInBandMgtConnKind is spvcInitiator(4), this object is target VCI. In all other cases, the value of this object is non-applicable. |
| ATM qbAtmInBandMgtConnKind | 1.3.6.1.4.1.4323.2.7.1.11.1.8 | AtmConnKind | read-create | This is the connection type associated with the in-band Management connection. The currently accepted types are pvc(1), spvcInitiator(4) and spvcTarget(5). |
| ATM qbAtmInBandMgtTxTd | 1.3.6.1.4.1.4323.2.7.1.11.1.9 | AtmTrafficDescrParamIndex | read-create | The Transmit traffic descriptor associated with this in-band management channel. |
| ATM qbAtmInBandMgtRxTd | 1.3.6.1.4.1.4323.2.7.1.11.1.10 | AtmTrafficDescrParamIndex | read-create | The Receive traffic descriptor associated with this in-band management channel. |
| ATM qbAtmInBandMgtTargetNsapAddr | 1.3.6.1.4.1.4323.2.7.1.11.1.11 | AtmAddr | read-create | If the value of qbAtmInBandMgtConnKind is spvcInitiator(4) this object represetns the Target NSAP Address of the connection. In all other cases, the value of this object is non-applicable. |
| ROW qbAtmInBandMgtRowStatus | 1.3.6.1.4.1.4323.2.7.1.11.1.12 | RowStatus | read-create | To create, or delete an Entry in this table. Setting this object to createAndGo(4) causes the corresponding row to be created. Setting this object to destroy(6) causes the corresponding row to be deleted. Note that -- currently-- only a single instance of a row can be created in this table. |
| qbAtmTrafficDescriptorTypes | 1.3.6.1.4.1.4323.2.7.1.12 | |||
| qbAtmPkt | 1.3.6.1.4.1.4323.2.7.1.12.1 | This traffic descriptor type is to define a connection with an Ethernet endpoint, and it is for a user that does not want to use ATM parameters directly. The EtherNet bandwidth will be converted to a nrtVbr traffic descriptor. The conversion from Ethernet bandwidth to ATM cell rate must add an ATM cell tax. This is defined using the pcbe (packet-to-cell bandwidth expansion) factor. If this is not defined for the traffic descriptor, then the system default (qbAtmDefaultPCBE)should be used. The use of the parameter vector for this type: Parameter 1: minbw, the minimum guarnteed bandwidth fo rthe connection. This is defined in Mb/sec. (0-100). Parameter 2: maxbw, the maximum bursting capability of the connection. This is defined in Mb/sec (1-100). It is default to minbw. Parameter 3: bw, indicates the bandwidth for the PON segment. Vaules are expressed in Mb, and may take interger value between 1 and 100. (only apply to 155Mb PON). It is default to minbw. Parameter 4: pcbe, it defines the packed-to-cell bandwidth expansion. This is the percentage overhead that is used to convert Ethernet bandwidth to ATM cell rates. It is default to qbAtmDefaultPCBE. Parameter 5: not used. | ||
| qbAtmConformance | 1.3.6.1.4.1.4323.2.7.2 | |||
| qbAtmCompliances | 1.3.6.1.4.1.4323.2.7.2.1 | |||
| qbAtmCompliance | 1.3.6.1.4.1.4323.2.7.2.1.1 | The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB. | ||
| qbAtmGroups | 1.3.6.1.4.1.4323.2.7.2.2 | |||
| qbAtmInterfaceConfGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.1 | The set of all accessible objects in the Interface group of this MIB. | ||
| qbAtmTrafficDescrParamGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.2 | The set of all accessible objects in the Traffic group of this MIB. | ||
| qbAtmVclGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.3 | The set of all accessible objects in the VCL group of this MIB. | ||
| qbAtmVplGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.4 | The set of all accessible objects in the VPL group of this MIB. | ||
| qbAtmVcCrossConnectGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.5 | The set of all accessible objects in the VPL group of this MIB. | ||
| qbAtmVpCrossConnectGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.6 | The set of all accessible objects in the VPL group of this MIB. | ||
| qbAtmPnniNodeGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.7 | The set of all accessible objects in the VPL group of this MIB. | ||
| qbAtmPnniIfGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.8 | The set of all accessible objects in the PNNI interface group of this MIB. | ||
| qbAtmPnniRouteAddrGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.9 | The set of all accessible objects in the Route group of this MIB. | ||
| qbAtmInterfaceConfSigGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.10 | The set of all accessible objects in the Route group of this MIB. | ||
| qbAtmPnniNbrPeerGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.11 | The set of all accessible objects in the PNNI Peer Nbr group of this MIB. | ||
| qbAtmPnniPglGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.12 | The set of all accessible objects in the PGL group of this MIB. | ||
| qbAtmPnniTimerGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.13 | The set of all accessible objects in the PNNI Timer group of this MIB. | ||
| qbAtmPnniLinkGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.14 | The set of all accessible objects in the PNNI Link group of this MIB. | ||
| qbAtmInBandMgtGroupInfo | 1.3.6.1.4.1.4323.2.7.2.2.15 | The set of all accessible objects in the in-band management group of this MIB. | ||
| qbAtmBaseGroup | 1.3.6.1.4.1.4323.2.7.3 | |||
| OCT qbAtmF4F5LLID | 1.3.6.1.4.1.4323.2.7.3.1 | OCTET STRING | read-write | This object stores Loopback Location ID (LLID). |
| INT qbAtmDefaultPCBE | 1.3.6.1.4.1.4323.2.7.3.2 | INTEGER | read-write | This object stores the default atm cell tax to be used by the system. |
RFC description
Vendor MIB module for managing ATM (Asynchronous Transfer Mode) network interfaces and related ATM objects on QB networking equipment.
Start monitoring Quantum Bridge ATM broadband access switch (PNNI signaling) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.