QB-DWS-MIB

All MIBs › QB-DWS-MIB

Organization: Quantum Bridge Communications, Inc.

Last Updated: 2001-07-07

Category: DSL and Broadband Access, Physical Layer and Interfaces

Description: Handles optical channel configuration and cross-connect state for Quantum Bridge Dense Wavelength Switching (DWS).

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is QB-DWS-MIB?

QB-DWS-MIB is a private Quantum Bridge Technologies MIB module that adds provisioning and management objects for Dense Wavelength Switching (DWS) optical links on Quantum Bridge devices. It is expected to expose objects for configuring and tracking optical channel/cross-connect assignments, such as which wavelength channel is mapped to which cross-connect path. Its monitoring value centers on confirming the operational/provisioning state of DWS cross-connects and optical channels — essentially a configuration and link-state health check for optical transport hardware — though no specific sample objects were supplied to confirm exact table names. It supplements a base Quantum Bridge DWS MIB (implied by 'additional objects' in its description) rather than standing alone, and is likely layered on general optical-networking management conventions. It would be deployed on Quantum Bridge DWS optical switching platforms in metro/DWDM transport networks where operators verify cross-connect provisioning and channel status. Configuring QB-DWS-MIB SNMP monitoring typically means polling these cross-connect and channel-state objects alongside the base Quantum Bridge MIB to get a complete picture of optical link health.

IPNetwork Monitor allows you to monitor SNMP objects defined in QB-DWS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Quantum Bridge DWS optical switching platforms

Monitoring Examples

No sample objects were provided for this module, so a concrete object-level scenario cannot be confirmed; based on its stated purpose of provisioning and managing DWS links, an operator would expect to poll cross-connect and optical-channel state objects to confirm a provisioned wavelength path is correctly established and operational, with a mismatched or down cross-connect state indicating a provisioning error or optical link fault.

Imported Objects

From ATM-TC-MIB

AtmAddr
AtmConnCastType
AtmConnKind
AtmServiceCategory
AtmTrafficDescrParamIndex
AtmVcIdentifier
AtmVorXAdminStatus
AtmVorXLastChange
AtmVorXOperStatus
AtmVpIdentifier
atmNoClpNoScr	OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From QBSYS-SYSTEM-MIB

qbSysIotSerialNumber	OBJECT-TYPE
qbSysModuleSlot	OBJECT-TYPE

From QUANTUMBRIDGE-REG

qbMibs

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using qbDwsIotIfStatsUtil OID:

Select a Quantum Bridge DWS optical switching platform as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type qbDwsIotIfStatsUtil into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the utilization of this IOT DWS interface's transmission-rate capacity, as a percentage. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if utilization exceeds 80%, since sustained high link utilization often precedes latency and packet loss. Click Finish to create the monitor; you can adjust any parameter later.

See also: qbTContNumber

OIDs

OID symbolic	OID numeric	Type	Access	Description
qbDwsMIB	1.3.6.1.4.1.4323.2.3			This module defines additional objects for the provisioning and management of DWS links in Quantum bridge devices.
qbDwsObjects	1.3.6.1.4.1.4323.2.3.1
qbDwsNetGroup	1.3.6.1.4.1.4323.2.3.1.1
INT qbDwsSysRangeMode	1.3.6.1.4.1.4323.2.3.1.1.1	INTEGER	read-write	The object that indicates a system wide range mode. When read, this object always returns the value 'ready(1)'. Setting this object to rangeAll(2) causes ranging of all IOTs that connect to this OAS.
INT qbSysIotRecoverMode	1.3.6.1.4.1.4323.2.3.1.1.2	INTEGER	read-write	The object allows to set the IOT auto-recovery feature on the IOAS. Auto-recovery is global in scope, so when it is enabled, auto-recovery is attempted for all IOTs that are attached to the IOAS.
qbDwsNetTable	1.3.6.1.4.1.4323.2.3.1.1.3		not-accessible	The Quantum Bridge PON Interface Table contains extensions of the standard MIB Interface Table, one entry per IOAS DWS interface. The table contains read-only objects and shows MIB objects for every Network interface
qbDwsNetEntry	1.3.6.1.4.1.4323.2.3.1.1.3.1		not-accessible	An entry in the Quantum Bridge DWS Interface Table that contains the Network interface's specific objects.
NUM qbDwsNetIfIndex	1.3.6.1.4.1.4323.2.3.1.1.3.1.1	InterfaceIndex	read-only	The value of this object is the same as the corresponding ifIndex of the Network Interface in the ifTable.
QBB qbDwsNetBw	1.3.6.1.4.1.4323.2.3.1.1.3.1.2	QbBitRate	read-only	The object indicates the total bandwidth rate that is available for reservation on this interface. This object is specified in Bits per second.
QBB qbDwsNetAllocatedBw	1.3.6.1.4.1.4323.2.3.1.1.3.1.3	QbBitRate	read-only	The object indicates the total bandwidth rate that is currently subscribed. The subscribed bandwidth rate consists of the bandwidth rate allocated for all provisoned connections. This object is specified in Bits per sec(Bps).
QBB qbDwsNetAvailableBw	1.3.6.1.4.1.4323.2.3.1.1.3.1.4	QbBitRate	read-only	The portion of this interface's capacity in bits per sec that is available for data traffic. This variable is adjusted for the allocated bandwidth. The formula for calculating this value is qbDwsNetBw - qbDwsNetAllocatedBw This object is specified in Bps.
QBB qbDwsNetAllocatedUbrBw	1.3.6.1.4.1.4323.2.3.1.1.3.1.5	QbBitRate	read-only	The object indicates the total number of bandwidth that are currently allocated for packet/ubr traffic. This object is specified in Bps.
QBB qbDwsNetAllocatedCbrBw	1.3.6.1.4.1.4323.2.3.1.1.3.1.6	QbBitRate	read-only	The object indicates the total number of bandwidth that is currently allocated for CBR traffic. This object is specified in Bps.
I32 qbDwsNetNumCbrConn	1.3.6.1.4.1.4323.2.3.1.1.3.1.7	Integer32	read-only	The object indicates the total number of inactive and in-service CBR connections that are currently provisioned on this interface.
I32 qbDwsNetNumUbrConn	1.3.6.1.4.1.4323.2.3.1.1.3.1.8	Integer32	read-only	The object indicates the total number of inactive and in-serice UBR connections that are currently provisioned on this interface.
I32 qbDwsNetNumIot	1.3.6.1.4.1.4323.2.3.1.1.3.1.9	Integer32	read-only	The number of IOTs that are provisioned on the Network interface.
QBD qbDwsNetTxStatus	1.3.6.1.4.1.4323.2.3.1.1.3.1.10	QbDwsIfStatus	read-only	This objects indicates the status of the DWS transmitter. The trap is generated by the SNMP agent when the IOAS DWS transmitter problem is detected. The trap contains the DWS module interface index.
TIM qbDwsNetTxStatusLastChange	1.3.6.1.4.1.4323.2.3.1.1.3.1.11	TimeStamp	read-only	The value of MIB II's sysUpTime object at the time this DWS Interface entered its current status state.
I32 qbDwsNetLosIotAddr	1.3.6.1.4.1.4323.2.3.1.1.3.1.12	Integer32	read-only	The object contains the address of the IOT for which a Los condition is detected. This indicates that no signal was detected within the expected time slot window. Note: The Los indication at the IOAS DWS card is a signal that an IOT is non-functioning.
TIM qbDwsNetLosIotTime	1.3.6.1.4.1.4323.2.3.1.1.3.1.13	TimeStamp	read-only	The value of MIB II's sysUpTime object at the time when the qbDwsNetIotLos condition was detected.
T/F qbDwsNetEncryptStatus	1.3.6.1.4.1.4323.2.3.1.1.3.1.14	TruthValue	read-write	The object that enables and disables encryption on this interface.
INT qbDwsNetRangeMode	1.3.6.1.4.1.4323.2.3.1.1.3.1.15	INTEGER	read-write	The object that indicates a range mode. When read, this object always returns the value 'ready(1)'. Setting this object to rangeAll(2) causes ranging of all IOTs connected to this interface.
C32 qbDwsNetRxTsCount	1.3.6.1.4.1.4323.2.3.1.1.3.1.16	Counter32	read-only	The total number of successfully received time slots.
C32 qbDwsNetTxTsCount	1.3.6.1.4.1.4323.2.3.1.1.3.1.17	Counter32	read-only	The total number of successfully transmitted time slots.
C32 qbDwsNetRxMissingTs	1.3.6.1.4.1.4323.2.3.1.1.3.1.18	Counter32	read-only	The number received time slots that have been missed.
C32 qbDwsNetRxIllegalTs	1.3.6.1.4.1.4323.2.3.1.1.3.1.19	Counter32	read-only	The number illegal received time slots that have been detected.
C32 qbDwsNetTxJabberTs	1.3.6.1.4.1.4323.2.3.1.1.3.1.20	Counter32	read-only	The number jabber transmitted time slots that have been detected.
C32 qbDwsNetTxOutOfFrameTs	1.3.6.1.4.1.4323.2.3.1.1.3.1.21	Counter32	read-only	The number out of frame transmitted timeslots that have been detected.
C32 qbDwsNetTxHdrCrcTsErrs	1.3.6.1.4.1.4323.2.3.1.1.3.1.22	Counter32	read-only	The number transmitted timeslots with the header protection error that have been detected.
C32 qbDwsNetOamRequests	1.3.6.1.4.1.4323.2.3.1.1.3.1.23	Counter32	read-only	The number of OAM requests. These OAM requests are originated by the IOAS and sent to downstream IOTs.
C32 qbDwsNetOamResponses	1.3.6.1.4.1.4323.2.3.1.1.3.1.24	Counter32	read-only	The number of OAM responses. These responses are generated by IOTs in response to downstream requests.
C32 qbDwsNetOamEvents	1.3.6.1.4.1.4323.2.3.1.1.3.1.25	Counter32	read-only	The number of OAM events. These events are originated by IOT devices to signal abnormal conditions.
C32 qbDwsNetOamBadMsgs	1.3.6.1.4.1.4323.2.3.1.1.3.1.26	Counter32	read-only	The total number of bad OAM messages.
INT qbDwsNetLoopBack	1.3.6.1.4.1.4323.2.3.1.1.3.1.27	INTEGER	read-write	The Loopback status of this DWS port. Writing configures the port to go into the loopback mode. When placed in loopback mode the DWS port does a 'payload' loopback.
qbDwsIotIfGroup	1.3.6.1.4.1.4323.2.3.1.2
qbDwsIotIfConfTable	1.3.6.1.4.1.4323.2.3.1.2.1		not-accessible	The Quantum DWS interface table. One entry per each IOT's DWS interface.
qbDwsIotIfConfEntry	1.3.6.1.4.1.4323.2.3.1.2.1.1		not-accessible	An entry in the Quantum Bridge DWS Interface Table. The ifIndex is a DWS interface index from ifTable.
NUM qbDwsIotIfIndex	1.3.6.1.4.1.4323.2.3.1.2.1.1.1	InterfaceIndex	not-accessible	The ifIndex of this interface in the ifTable.
NUM qbDwsIotNetIfIndex	1.3.6.1.4.1.4323.2.3.1.2.1.1.2	InterfaceIndex	read-only	The ifIndex of this PON interface in the ifTable.
I32 qbDwsIotIfAddr	1.3.6.1.4.1.4323.2.3.1.2.1.1.3	Integer32	read-only	The IOT terminal address.
I32 qbDwsIotIfConfPowerLevel	1.3.6.1.4.1.4323.2.3.1.2.1.1.4	Integer32	read-only	The DWS interface's power level.
TIK qbDwsIotIfConfEqDelay	1.3.6.1.4.1.4323.2.3.1.2.1.1.5	TimeTicks	read-only	The equal Delay time (in hundredths of a second).
I32 qbDwsIotIfConfWaveLength	1.3.6.1.4.1.4323.2.3.1.2.1.1.6	Integer32	read-only	The wave length value for this DWS interface.
QBB qbDwsIotIfUbrBw	1.3.6.1.4.1.4323.2.3.1.2.1.1.7	QbBitRate	read-only	The object indicates the total UBR bandwidth rate that is reserved for a given IOT interface. This object is specified in Bits per second.
QBB qbDwsIotIfCbrBw	1.3.6.1.4.1.4323.2.3.1.2.1.1.8	QbBitRate	read-only	The object indicates the total CBR bandwidth rate that is reserved for a given IOT interface. This object is specified in Bits per second.
QBD qbDwsIotIfTxStatus	1.3.6.1.4.1.4323.2.3.1.2.1.1.9	QbDwsIfStatus	read-only	This objects indicates the status of the IOT DWS Port. The txFailure(2) state indicates that the laser transmitter failed. The rxFailure(3) state indicates that no signal was detected within the expected timeslot window. It signals that there is a problem with the DWS port receiver. When this object is changed, the ifOperStatus and ifLastChnaged of this interface must also be changed. Note: The trap is generated by the SNMP agent when the IOT DWS status is changed. The trap contains the IOAS DWS card interface index and IOT address.
TIM qbDwsIotIfTxStatusLastChange	1.3.6.1.4.1.4323.2.3.1.2.1.1.10	TimeStamp	read-only	The value of MIB II's sysUpTime object at the time this DWS Interface enters its current status state.
TIM qbDwsIotIfLastRangeTime	1.3.6.1.4.1.4323.2.3.1.2.1.1.11	TimeStamp	read-only	The value of MIB II's sysUpTime object at the last time when this IOT is ranged
qbDwsIotIfStatsTable	1.3.6.1.4.1.4323.2.3.1.2.2		not-accessible	The Quantum Bridge IOT's terminal table. One entry per each RT.
qbDwsIotIfStatsEntry	1.3.6.1.4.1.4323.2.3.1.2.2.1		not-accessible	An entry in the Quantum DWS Interface Statistics Table.
INT qbDwsIotIfStatsUtilEx	1.3.6.1.4.1.4323.2.3.1.2.2.1.1	INTEGER	read-only	The object indicates the utilization of the Network Interface transmission rate capacity by the IOT DWS interface. This object is specified in percents.
C32 qbDwsIotIfStatsOamRequests	1.3.6.1.4.1.4323.2.3.1.2.2.1.2	Counter32	read-only	The number of received downstream OAM request messages.
C32 qbDwsIotIfStatsOamResponses	1.3.6.1.4.1.4323.2.3.1.2.2.1.3	Counter32	read-only	The number of transmitted upstream OAM response messages.
C32 qbDwsIotIfStatsOamEvents	1.3.6.1.4.1.4323.2.3.1.2.2.1.4	Counter32	read-only	The number of OAM event messages originated by the interface.
C32 qbDwsIotIfStatsOamBadMsgs	1.3.6.1.4.1.4323.2.3.1.2.2.1.5	Counter32	read-only	The number of wrong OAM messages received on this interface.
C32 qbDwsIotIfStatsCrcErrs	1.3.6.1.4.1.4323.2.3.1.2.2.1.6	Counter32	read-only	The summary number of the IOT DWS CRC subframe and time slot header CRC errors.
C32 qbDwsIotIfStatsTsHdrParityErrs	1.3.6.1.4.1.4323.2.3.1.2.2.1.7	Counter32	read-only	The number of Time Slot header parity errors that have been detected on the interface.
C32 qbDwsIotIfStatsFrameLossErrs	1.3.6.1.4.1.4323.2.3.1.2.2.1.8	Counter32	read-only	The number of Loss frame errors that have been detected on the interface.
C32 qbDwsIotIfStatsSignalLossErrs	1.3.6.1.4.1.4323.2.3.1.2.2.1.9	Counter32	read-only	The number of Loss signal errors that have been detected on the interface.
C32 qbDwsIotIfStatsRxAal1Cells	1.3.6.1.4.1.4323.2.3.1.2.2.1.10	Counter32	read-only	The number of received AAL1 ATM cells.
C32 qbDwsIotIfStatsTxAal1Cells	1.3.6.1.4.1.4323.2.3.1.2.2.1.11	Counter32	read-only	The number of transmitted ATM cells .
qbIotPktIfGroup	1.3.6.1.4.1.4323.2.3.1.3
qbIotPktIfConfTable	1.3.6.1.4.1.4323.2.3.1.3.1		not-accessible	The Quantum Bridge PKT configuration table contains cross-connections between Ethernet interfaces and corresponding PVC/AAL5 that are configured at a WAN port. An entry in the table may be created, destroyed or modified. This table lists all PVCs within the System that send/receive packet traffic to/from the ATM cloud.
qbIotPktIfConfEntry	1.3.6.1.4.1.4323.2.3.1.3.1.1		not-accessible	An entry in the Quantum Bridge IP configuration table. For every IP traffic flow, there is a corresponding row in this table which contains a DWS interface index, and a VPI/VCI pair of PVC configured at a SONET port for a given DWS interface. The creation of a row in this table causes a corresponding entry in the atmVclTable of the ATM-MIB to be automatically created if an atmVclEntry with qbPktIotIfConfVpi and qbPktIotIfConfVci values does not exist. This corresponding entry can be removed only if the qbPktIotIfConfEntry is removed. The qbPktIotIfConfIndex of this table is an ifIndex of the DWS interface from the ifTable.
NUM qbIotPktIfConfIndex	1.3.6.1.4.1.4323.2.3.1.3.1.1.1	InterfaceIndex	not-accessible	An interface index of the Ethernet port interface.
NUM qbAtmIfIndex	1.3.6.1.4.1.4323.2.3.1.3.1.1.2	InterfaceIndex	read-create	An interface index of the ATM interface that is stacked on top of the WAN/SONET interface.
OID qbIotPktIfConfVpi	1.3.6.1.4.1.4323.2.3.1.3.1.1.3	AtmVpIdentifier	read-create	A VPI of the AAL5 PVC that connects this interface to the ATM cloud. This PVC is automatically configured at the SONET port of the WAN card (atmVclTable).
OID qbIotPktIfConfVci	1.3.6.1.4.1.4323.2.3.1.3.1.1.4	AtmVcIdentifier	read-create	A VCI of the AAL5 bi-directional PVC that connects this interface to the ATM cloud. This PVC is automatically configured or removed at the SONET port of the WAN card (atmVclTable).
STR qbIotPktIfConfConnName	1.3.6.1.4.1.4323.2.3.1.3.1.1.5	DisplayString	read-create	The textual name of the connection(PVC) as specified by a user. It provides a non-volatile handle for this PVC. The supplied name in the qbPktIotIfConfPvcName is associated with the same PVC for as long as that PVC/conection remains.
ATM qbIotPktIfConfRxTrafficDescrIndex	1.3.6.1.4.1.4323.2.3.1.3.1.1.6	AtmTrafficDescrParamIndex	read-create	The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCL.
ATM qbIotPktIfConfTxTrafficDescrIndex	1.3.6.1.4.1.4323.2.3.1.3.1.1.7	AtmTrafficDescrParamIndex	read-create	The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.
ATM qbIotPktIfConfAdminStatus	1.3.6.1.4.1.4323.2.3.1.3.1.1.8	AtmVorXAdminStatus	read-create	The desired administrative status of the packet connection The up and down states indicate that the traffic flow is enabled or disabled respectively across the ATM cloud.
ATM qbIotPktIfConfOperStatus	1.3.6.1.4.1.4323.2.3.1.3.1.1.9	AtmVorXOperStatus	read-only	The current operational status of the connect.
ROW qbIotPktIfConfRowStatus	1.3.6.1.4.1.4323.2.3.1.3.1.1.10	RowStatus	read-create	The status column for this IOT ENET interface. This OBJECT can be set to: createAndGo(4) destroy(6) The following values may be read: active(1) This object may only be set to createAndGo(4). Setting this object to active(1) when its value is already active(1) is a no-op. Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to destroy(6) will remove the corresponding entry in this table, and disable data traffic.
QBE qbIotPktIfConfLoopback	1.3.6.1.4.1.4323.2.3.1.3.1.1.11	QbEnableStatus	read-create	This object enables loopback on the IOT ENET enedpoint.
QBP qbIotPktIfConfConnKind	1.3.6.1.4.1.4323.2.3.1.3.1.1.12	QbPvcConnKind	read-create	The PVC connection type.
qbIotAddrGroup	1.3.6.1.4.1.4323.2.3.1.4
qbIotAddrTable	1.3.6.1.4.1.4323.2.3.1.4.1		not-accessible	The Quantum Bridge IOT address table. This table contains information to convert an IOT's address into an IOT's serial number. This table has two indexes: 1. Interface index of the IOAS interface to which a terminal connects. The interface identified by a particular value of this index is the same as the interface identified by the same value of ifIndex. 2. IOT terminal address. A row exists in this table for each discovered IOT terminal. Whenever an IOT is discovered a row is added to the table
qbIotAddrEntry	1.3.6.1.4.1.4323.2.3.1.4.1.1		not-accessible	For every IOT terminal there is a row in this table. This contains the IOT address and serial number.
I32 qbIotAddr	1.3.6.1.4.1.4323.2.3.1.4.1.1.1	Integer32	not-accessible	The IOT's address.
QBS qbIotSerialNum	1.3.6.1.4.1.4323.2.3.1.4.1.1.2	QbSerialNum	read-only	The IOT's serial number.
qbIotPortCrossConnGroup	1.3.6.1.4.1.4323.2.3.1.5
qbIotPortCrossConnTable	1.3.6.1.4.1.4323.2.3.1.5.1		not-accessible	The Quantum Bridge IOT port cross-connection table. This table defines all IOT port point-to-point cross-connections within a single OAS system. The connection can be set between two Ethernet, two DS1 or two E1 ports on different IOTs. The table has two indexes: the interface index of the first end-point and the interface index of the second endpoint. Note: Connections that are listed in this table are not reflected in the atmVclTable.
qbIotPortCrossConnEntry	1.3.6.1.4.1.4323.2.3.1.5.1.1		not-accessible	An entry in the Quantum Bridge qbIotPortConnTable two contains a connection between the same port type of different IOTs.
NUM qbIotPortCrossConnEndpt1IfIndex	1.3.6.1.4.1.4323.2.3.1.5.1.1.1	InterfaceIndex	not-accessible	The ifIndex of the first IOT port((end-point) for the configured IOT cross-connect.
NUM qbIotPortCrossConnEndpt2IfIndex	1.3.6.1.4.1.4323.2.3.1.5.1.1.2	InterfaceIndex	not-accessible	The ifIndex of the second IOT port(end-point) for the configured IOT cross-connect.
ATM qbIotPortCrossConnAdminStatus	1.3.6.1.4.1.4323.2.3.1.5.1.1.3	AtmVorXAdminStatus	read-create	The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.
ATM qbIotPortCrossConnOperStatus	1.3.6.1.4.1.4323.2.3.1.5.1.1.4	AtmVorXOperStatus	read-only	The current operational status of the connection.
ATM qbIotPortCrossConnLastChange	1.3.6.1.4.1.4323.2.3.1.5.1.1.5	AtmVorXLastChange	read-only	The value of sysUpTime at the time this connection entered its current operational state.
ATM qbIotPortCrossConnRxTrafficDescrIndex	1.3.6.1.4.1.4323.2.3.1.5.1.1.6	AtmTrafficDescrParamIndex	read-create	The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this connection.
ATM qbIotPortCrossConnTxTrafficDescrIndex	1.3.6.1.4.1.4323.2.3.1.5.1.1.7	AtmTrafficDescrParamIndex	read-create	The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this connection.
STR qbIotPortCrossConnName	1.3.6.1.4.1.4323.2.3.1.5.1.1.8	DisplayString	read-create	The textual name of the connection as specified by a user. It provides a non-volatile handle for this connection. The supplied name in the qbIotPortConnName is associated with the same connection for as long as that conection remains.
ROW qbIotPortCrossConnRowStatus	1.3.6.1.4.1.4323.2.3.1.5.1.1.9	RowStatus	read-create	The status of the port connect entry. Changing the value of this object from 'active' to 'destroy' will remove this entry from the database. It will disrupt traffic between two IOT packet interfaces.
QBE qbIotPortCrossConnLoopback	1.3.6.1.4.1.4323.2.3.1.5.1.1.10	QbEnableStatus	read-create	This object enables loopback on this IOT to IOT port enedpoint. The endpoint on which loopback is enabled is defined by qbIotPortCrossConnLoopbackEndpt.
INT qbIotPortCrossConnLoopbackEndpt	1.3.6.1.4.1.4323.2.3.1.5.1.1.11	INTEGER	read-create	This object defines loopback on the selected endpoint.
QBP qbIotPortCrossConnKind	1.3.6.1.4.1.4323.2.3.1.5.1.1.12	QbPvcConnKind	read-create	The VCL connection type.
qbTContGroup	1.3.6.1.4.1.4323.2.3.1.6
I32 qbTContNumberEx	1.3.6.1.4.1.4323.2.3.1.6.1	Integer32	read-only	The total number of provisioned Ethernet to ATM PVCs.
I32 qbNextFreeTContIndex	1.3.6.1.4.1.4323.2.3.1.6.2	Integer32	read-only	The next available Container index.
qbTContTable	1.3.6.1.4.1.4323.2.3.1.6.3		not-accessible	The Quantum Bridge Traffic Container table(TCons) contains traffic containers of IOTs.
qbTContEntry	1.3.6.1.4.1.4323.2.3.1.6.3.1		not-accessible	An entry in the qbTContTable. There is one entry in the table per IOT on the PON for Release 3.0. The creation of a row in the qbSysIotTable causes a corresponding entry in this table to be automatically created. The deletion of a row in the qbSysIotTable causes a corresponding entry in this table to be automatically removed.
INT qbTContIndex	1.3.6.1.4.1.4323.2.3.1.6.3.1.1	INTEGER	not-accessible	The value of this object identifies the row of the Traffic Container Table. Note tht this value can be set to 1 only for Release 3.0.
INT qbTContType	1.3.6.1.4.1.4323.2.3.1.6.3.1.2	INTEGER	read-write	The Traffic container type. Note that this object can be set to type1 for Release 3.0
INT qbTContMaxBw	1.3.6.1.4.1.4323.2.3.1.6.3.1.3	INTEGER	read-write	The maximum bandwidth to be assigned to this TCONT. Note that the read-only access is supported for Release 3.0
INT qbTContFixedBw	1.3.6.1.4.1.4323.2.3.1.6.3.1.4	INTEGER	read-write	The lower limit of bandwidth for this TCONT.
INT qbTContAssuredBw	1.3.6.1.4.1.4323.2.3.1.6.3.1.5	INTEGER	read-write	The guaranteed minimum bandwidth for this TCONT. TCONT. Note that the read-only access is supported for Release 3.0
INT qbTContGrantNum	1.3.6.1.4.1.4323.2.3.1.6.3.1.6	INTEGER	read-write	FSAN grant number that is assigned to this TCONT. Note that the read-only access is supported for Release 3.0
qbDwsNotifications	1.3.6.1.4.1.4323.2.3.2
qbDwsNotificationPrefix	1.3.6.1.4.1.4323.2.3.2.0
NTF qbDwsIotRxLos	1.3.6.1.4.1.4323.2.3.2.0.1			A qbDwsIotRxLos trap indicates Loss of Signal by the IOT's. This trap is generated by an IOT when Analog DS1/E1 Analog or Digital Los occur.
NTF qbDwsRxIoasLos	1.3.6.1.4.1.4323.2.3.2.0.2			A qbDwsRxIoasLos trap indicates Loss of Signal by the IOAS's DWS receiver. This trap is generated by an IOAS DWS card when no signal from an IOT is detected within the timeslot window.
NTF qbDwsIoasTxFailure	1.3.6.1.4.1.4323.2.3.2.0.3			A qbDwsTxFailure trap indicates that the IOAS card transmitter does not work. The trap is generated by an IOAS card when the IOAS DWS card transmitter problem is detected. The trap contains the DWS card interface index.
NTF qbDwsIotRangeTimeout	1.3.6.1.4.1.4323.2.3.2.0.4			A qbDwsTxFailure trap indicates that IOT not responding during the ranging process.
qbDwsConformance	1.3.6.1.4.1.4323.2.3.3
qbDwsCompliances	1.3.6.1.4.1.4323.2.3.3.1
qbDwsCompliance	1.3.6.1.4.1.4323.2.3.3.1.1			The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB.
qbDwsGroups	1.3.6.1.4.1.4323.2.3.3.2
qbDwsNetGroupInfo	1.3.6.1.4.1.4323.2.3.3.2.1			The set of all accessible objects in the DWS Network Group of this MIB.
qbDwsIotGroupInfo	1.3.6.1.4.1.4323.2.3.3.2.2			The set of all accessible objects in the IOT Group of this MIB.
qbDwsPktGroupInfo	1.3.6.1.4.1.4323.2.3.3.2.3			The set of all accessible objects in the Packet Group ofthis MIB.
qbDwsIotAddrGroupInfo	1.3.6.1.4.1.4323.2.3.3.2.4			The set of all accessible objects in the IOT address group of this MIB.

RFC description

Manages Quantum Bridge Dense Wavelength Switching (DWS) optical channel configuration and cross-connect state.

Start monitoring Quantum Bridge DWS optical switching platforms with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download QB-DWS-MIB

What Is QB-DWS-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

How to Use in IPNetwork Monitor

RFC description