Nortel-Magellan-Passport-AtmPnniMIB

All MIBs › Nortel-Magellan-Passport-AtmPnniMIB

Category: ATM

Description: Manages Nortel Magellan Passport ATM PNNI routing protocol topology, peer groups, and reachability.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-Magellan-Passport-AtmPnniMIB?

This Nortel Magellan Passport module manages PNNI (Private Network-to-Network Interface) ATM routing protocol configuration on Passport switches, covering topology, peer group membership, and reachability information used for dynamic ATM call routing. It exposes provisioning tables (atmIfVptPnniProvTable) and row-status tables (atmIfVptPnniRowStatusTable) for PNNI-enabled interfaces, along with signaling-related retry and hold-off timer settings for soft PVC/PVP connections. In monitoring terms it verifies PNNI protocol configuration health: confirming PNNI interfaces are correctly provisioned and active, and that soft PVC/PVP retry periods and hold-off timers are set appropriately to control how quickly failed soft connections are retried, which matters for network resilience during link failures. As a PNNI-specific module it depends on the ATM Forum's PNNI routing standard and sits alongside the sibling AtmBearerServiceMIB in the Passport MIB family, sharing row-status/component conventions. It was deployed on Nortel Magellan Passport ATM switches forming carrier-grade ATM backbone networks using dynamic PNNI routing, where Nortel-Magellan-Passport-AtmPnniMIB SNMP monitoring helped confirm PNNI interfaces stayed correctly provisioned and active.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-AtmPnniMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Magellan Passport ATM switch

Monitoring Examples

An operator troubleshooting slow reconvergence after an ATM link failure would check atmIfVptPnniSoftPvcRetryPeriod and atmIfVptPnniSoftPvpAndPvcHoldOffTime to confirm the configured retry/hold-off intervals for soft PVC/PVP re-establishment, and poll atmIfVptPnniProvTable/atmIfVptPnniProvEntry to verify PNNI interface provisioning is correct. A row in atmIfVptPnniRowStatusTable stuck outside the active state would indicate the PNNI interface failed to come up, disrupting topology advertisement to peer nodes.

What Can Be Monitored

PNNI interface provisioning/status
soft PVC/PVP retry period
soft PVC/PVP hold-off time
row status of PNNI-enabled interfaces

Imported Objects

From Nortel-Magellan-Passport-AtmCoreMIB

atmIf	OBJECT-IDENTITY
atmIfIndex	OBJECT-TYPE
atmIfVpt	OBJECT-IDENTITY
atmIfVptIndex	OBJECT-TYPE

From Nortel-Magellan-Passport-StandardTextualConventionsMIB

Counter32
DisplayString
Gauge32
Integer32
RowStatus
StorageType
Unsigned32

From Nortel-Magellan-Passport-TextualConventionsMIB

AsciiStringIndex
FixedPoint1
Hex
HexString
NonReplicated

From Nortel-Magellan-Passport-UsefulDefinitionsMIB

passportMIBs

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
atmIfVptPnni	1.3.6.1.4.1.562.2.4.1.114.9.7
atmIfVptPnniRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnni components.
atmIfVptPnniRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnni component.
ROW atmIfVptPnniRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptPnni components. These components can be added and deleted.
STR atmIfVptPnniComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnni tables.
NON atmIfVptPnniIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptPnni tables.
atmIfVptPnniSig	1.3.6.1.4.1.562.2.4.1.114.9.7.2
atmIfVptPnniSigRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnniSig components.
atmIfVptPnniSigRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnniSig component.
ROW atmIfVptPnniSigRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfVptPnniSig components. These components cannot be added nor deleted.
STR atmIfVptPnniSigComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniSigStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnniSig tables.
NON atmIfVptPnniSigIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptPnniSig tables.
atmIfVptPnniSigVcd	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2
atmIfVptPnniSigVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnniSigVcd components.
atmIfVptPnniSigVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnniSigVcd component.
ROW atmIfVptPnniSigVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptPnniSigVcd components. These components can be added and deleted.
STR atmIfVptPnniSigVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniSigVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnniSigVcd tables.
NON atmIfVptPnniSigVcdIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptPnniSigVcd tables.
atmIfVptPnniSigVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfVptPnniSigVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10.1		not-accessible	An entry in the atmIfVptPnniSigVcdProvTable.
INT atmIfVptPnniSigVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfVptPnniSigVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfVptPnniSigVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfVptPnniSigVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfVptPnniSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfVptPnniSigVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfVptPnniSigVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfVptPnniSigVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.387.1		not-accessible	An entry in the atmIfVptPnniSigVcdTdpTable.
I32 atmIfVptPnniSigVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfVptPnniSigVcdTdpTable specific index for the atmIfVptPnniSigVcdTdpTable.
U32 atmIfVptPnniSigVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.9.7.2.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfVptPnniSigVcdTdpTable.
atmIfVptPnniSigProvTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
atmIfVptPnniSigProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.10.1		not-accessible	An entry in the atmIfVptPnniSigProvTable.
U32 atmIfVptPnniSigVci	1.3.6.1.4.1.562.2.4.1.114.9.7.2.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT atmIfVptPnniSigAddressConversion	1.3.6.1.4.1.562.2.4.1.114.9.7.2.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
atmIfVptPnniSigStateTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfVptPnniSigStateEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.11.1		not-accessible	An entry in the atmIfVptPnniSigStateTable.
INT atmIfVptPnniSigAdminState	1.3.6.1.4.1.562.2.4.1.114.9.7.2.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfVptPnniSigOperationalState	1.3.6.1.4.1.562.2.4.1.114.9.7.2.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfVptPnniSigUsageState	1.3.6.1.4.1.562.2.4.1.114.9.7.2.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfVptPnniSigOperTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
atmIfVptPnniSigOperEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.12.1		not-accessible	An entry in the atmIfVptPnniSigOperTable.
U32 atmIfVptPnniSigLastTxCauseCode	1.3.6.1.4.1.562.2.4.1.114.9.7.2.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfVptPnniSigLastTxDiagCode	1.3.6.1.4.1.562.2.4.1.114.9.7.2.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 atmIfVptPnniSigLastRxCauseCode	1.3.6.1.4.1.562.2.4.1.114.9.7.2.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfVptPnniSigLastRxDiagCode	1.3.6.1.4.1.562.2.4.1.114.9.7.2.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
atmIfVptPnniSigStatsTable	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
atmIfVptPnniSigStatsEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1		not-accessible	An entry in the atmIfVptPnniSigStatsTable.
C32 atmIfVptPnniSigCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 atmIfVptPnniSigPeakConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 atmIfVptPnniSigSuccessfulConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptPnniSigFailedConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptPnniSigTxPdus	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptPnniSigRxPdus	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfVptPnniSigCurrentPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 atmIfVptPnniSigPeakPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 atmIfVptPnniSigSuccessfulPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptPnniSigFailedPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfVptPnniSigNewCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.9.7.2.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
atmIfVptPnniRcc	1.3.6.1.4.1.562.2.4.1.114.9.7.3
atmIfVptPnniRccRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnniRcc components.
atmIfVptPnniRccRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnniRcc component.
ROW atmIfVptPnniRccRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfVptPnniRcc components. These components cannot be added nor deleted.
STR atmIfVptPnniRccComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniRccStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnniRcc tables.
NON atmIfVptPnniRccIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptPnniRcc tables.
atmIfVptPnniRccVcd	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2
atmIfVptPnniRccVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnniRccVcd components.
atmIfVptPnniRccVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnniRccVcd component.
ROW atmIfVptPnniRccVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptPnniRccVcd components. These components can be added and deleted.
STR atmIfVptPnniRccVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniRccVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnniRccVcd tables.
NON atmIfVptPnniRccVcdIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptPnniRccVcd tables.
atmIfVptPnniRccVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfVptPnniRccVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10.1		not-accessible	An entry in the atmIfVptPnniRccVcdProvTable.
INT atmIfVptPnniRccVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfVptPnniRccVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfVptPnniRccVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfVptPnniRccVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfVptPnniRccVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfVptPnniRccVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfVptPnniRccVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfVptPnniRccVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.387.1		not-accessible	An entry in the atmIfVptPnniRccVcdTdpTable.
I32 atmIfVptPnniRccVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfVptPnniRccVcdTdpTable specific index for the atmIfVptPnniRccVcdTdpTable.
U32 atmIfVptPnniRccVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.9.7.3.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfVptPnniRccVcdTdpTable.
atmIfVptPnniRccProvTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.10		not-accessible	This group contains the generic provisionable attributes of an Rcc component.
atmIfVptPnniRccProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.10.1		not-accessible	An entry in the atmIfVptPnniRccProvTable.
U32 atmIfVptPnniRccVci	1.3.6.1.4.1.562.2.4.1.114.9.7.3.10.1.1	Unsigned32	read-write	This attribute specifies the VCI for the Routing Control Channel (RCC). It is not recommended that the value be changed from the default of 18 unless absolutely necessary. If a different VCI is specified, ensure that the RCC at the far end is provisioned to use the same VCI, otherwise the RCC will not come up.
atmIfVptPnniRccHlParmsTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.11		not-accessible	This group contains the provisionable Hello protocol parameters for an Rcc component.
atmIfVptPnniRccHlParmsEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.11.1		not-accessible	An entry in the atmIfVptPnniRccHlParmsTable.
NUM atmIfVptPnniRccHelloHoldDown	1.3.6.1.4.1.562.2.4.1.114.9.7.3.11.1.1	FixedPoint1	read-write	This attribute is used to limit the rate at which this node sends out Hello packets. Specifically, it specifies the minimum time between successive Hellos. A value of 0 specifies that the value provisioned for the helloHoldDown attribute of the ARtg Pnni component should be used.
U32 atmIfVptPnniRccHelloInterval	1.3.6.1.4.1.562.2.4.1.114.9.7.3.11.1.2	Unsigned32	read-write	This attribute specifies the duration of the Hello Timer. Every helloInterval seconds, this node will send out a Hello packet to the neighbor node, subject to the helloHoldDown timer having expired at least once since the last Hello packet was sent. A value of 0 specifies that the value provisioned for the helloInterval attribute of the ARtg Pnni component should be used.
U32 atmIfVptPnniRccHelloInactivityFactor	1.3.6.1.4.1.562.2.4.1.114.9.7.3.11.1.3	Unsigned32	read-write	This attribute specifies the number of Hello intervals allowed to pass without receiving a Hello from the neighbor node, before an attempt is made to re-stage. The hello inactivity timer is enabled in the oneWayInside, twoWayInside, oneWayOutside, twoWayOutside and commonOutside hello states (see the helloState attribute on the Rcc component for a description of these states). Note that the value for the Hello interval used in the calculation is the one specified in the Hello packet from the neighbor node. A value of 0 specifies that the value provisioned for the helloInactivityFactor attribute of the ARtg Pnni component should be used. DESCRIPTION
atmIfVptPnniRccStateTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfVptPnniRccStateEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.12.1		not-accessible	An entry in the atmIfVptPnniRccStateTable.
INT atmIfVptPnniRccAdminState	1.3.6.1.4.1.562.2.4.1.114.9.7.3.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfVptPnniRccOperationalState	1.3.6.1.4.1.562.2.4.1.114.9.7.3.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfVptPnniRccUsageState	1.3.6.1.4.1.562.2.4.1.114.9.7.3.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfVptPnniRccOperTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.13		not-accessible	This group contains the operational attributes for an Rcc component.
atmIfVptPnniRccOperEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.13.1		not-accessible	An entry in the atmIfVptPnniRccOperTable.
INT atmIfVptPnniRccType	1.3.6.1.4.1.562.2.4.1.114.9.7.3.13.1.1	INTEGER	read-only	This attribute indicates the role of this link in the PNNI hierarchy. The following values are possible: unknown: the Hello protocol has not yet determined the role of the link. lowestLevelHorizLink: the link is a horizontal link between two lowest level nodes. lowestLevelOutsideLink: the link is an outside link between two border nodes. horizontalLinkToLgn: the link is a horizontal link to a Logical Group Node (LGN). uplink: the link is a uplink to a higher level LGN.
INT atmIfVptPnniRccNegotiatedVersion	1.3.6.1.4.1.562.2.4.1.114.9.7.3.13.1.2	INTEGER	read-only	This attribute indicates the PNNI version negotiated with the neighbor node.
INT atmIfVptPnniRccHelloState	1.3.6.1.4.1.562.2.4.1.114.9.7.3.13.1.3	INTEGER	read-only	This attribute indicates the state of the Hello protocol exchange over this link. The following are the possible values for this attribute: down: the link is down; no PNNI routing packets will be sent over or received over such a link. This is the initial state of the Hello Finite State Machine, and can also be reached when lower-level protocols have indicated that the link is not usable. attempt: no Hello packets or Hello packets, with mismatch information, have been received recently from the neighbor. Attempts are made to contact the neighbor node by sending out Hello packets every helloInterval seconds. oneWayInside: Hello packets have been recently received from the neighbor and it has been established that both nodes are members of the same peer group, but the remote node ID and remote port ID in the neighbor's Hello packets were set to zero. A Hello packet is sent to the neighbor and the Hello timer is restarted. twoWayInside: Bidirectional communication over this link between this node and the neighbor node has been achieved. oneWayOutside: Hello packets have been recently received from the neighbor and it has been established that both nodes are members of a different peer group, but the remote node ID and remote port ID in the neighbor's Hello packets were set to zero. twoWayOutside: Hellos have recently been received from the neighbor indicating that the neighbor node belongs to a different peer group. The correct remote node ID and remote port ID fields were included in the Hello packet, but the nodal hierarchy list did not include any common peer group. This state can also be reached if a hierarchy mismatch occurs while in the commonOutside state. commonOutside: A common level of the routing hierarchy has been found, in addition to achieving full bi-directional communication between the two nodes.
STR atmIfVptPnniRccRemoteNodeId	1.3.6.1.4.1.562.2.4.1.114.9.7.3.13.1.4	HexString	read-only	This attribute indicates the neighbor node's node id.
U32 atmIfVptPnniRccRemotePortId	1.3.6.1.4.1.562.2.4.1.114.9.7.3.13.1.5	Unsigned32	read-only	This attribute indicates the neighbor node's port id.
atmIfVptPnniRccStatsTable	1.3.6.1.4.1.562.2.4.1.114.9.7.3.14		not-accessible	This group contains the statistical attributes for an Rcc component.
atmIfVptPnniRccStatsEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.3.14.1		not-accessible	An entry in the atmIfVptPnniRccStatsTable.
C32 atmIfVptPnniRccHelloPacketsRx	1.3.6.1.4.1.562.2.4.1.114.9.7.3.14.1.1	Counter32	read-only	This attribute counts the total number of Hello packets received across this RCC, including bad and mismatched Hello packets. The counter wraps when it exceeds the maximum value.
C32 atmIfVptPnniRccHelloPacketsTx	1.3.6.1.4.1.562.2.4.1.114.9.7.3.14.1.2	Counter32	read-only	This attribute counts the total number of Hello packets transmitted across this RCC. The counter wraps when it exceeds the maximum value.
C32 atmIfVptPnniRccMismatchedHelloPacketsRx	1.3.6.1.4.1.562.2.4.1.114.9.7.3.14.1.3	Counter32	read-only	This attribute counts the total number of mismatched Hello packets received over this RCC. The counter wraps when it exceeds the maximum value.
C32 atmIfVptPnniRccBadHelloPacketsRx	1.3.6.1.4.1.562.2.4.1.114.9.7.3.14.1.4	Counter32	read-only	This attribute counts the total number of bad Hello packets received over this RCC. The counter wraps when it exceeds the maximum value.
atmIfVptPnniAddr	1.3.6.1.4.1.562.2.4.1.114.9.7.4
atmIfVptPnniAddrRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.4.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnniAddr components.
atmIfVptPnniAddrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.4.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnniAddr component.
ROW atmIfVptPnniAddrRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptPnniAddr components. These components can be added and deleted.
STR atmIfVptPnniAddrComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniAddrStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnniAddr tables.
STR atmIfVptPnniAddrAddressIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.4.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the atmIfVptPnniAddr tables.
INT atmIfVptPnniAddrAddressTypeIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.4.1.1.11	INTEGER	not-accessible	This variable represents an index for the atmIfVptPnniAddr tables.
atmIfVptPnniAddrTermSP	1.3.6.1.4.1.562.2.4.1.114.9.7.4.2
atmIfVptPnniAddrTermSPRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.4.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnniAddrTermSP components.
atmIfVptPnniAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.4.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnniAddrTermSP component.
ROW atmIfVptPnniAddrTermSPRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptPnniAddrTermSP components. These components can be added and deleted.
STR atmIfVptPnniAddrTermSPComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniAddrTermSPStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnniAddrTermSP tables.
NON atmIfVptPnniAddrTermSPIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.4.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptPnniAddrTermSP tables.
atmIfVptPnniAddrPnniInfo	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3
atmIfVptPnniAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.1		not-accessible	This entry controls the addition and deletion of atmIfVptPnniAddrPnniInfo components.
atmIfVptPnniAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.1.1		not-accessible	A single entry in the table represents a single atmIfVptPnniAddrPnniInfo component.
ROW atmIfVptPnniAddrPnniInfoRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptPnniAddrPnniInfo components. These components can be added and deleted.
STR atmIfVptPnniAddrPnniInfoComponentName	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptPnniAddrPnniInfoStorageType	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptPnniAddrPnniInfo tables.
NON atmIfVptPnniAddrPnniInfoIndex	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptPnniAddrPnniInfo tables.
atmIfVptPnniAddrPnniInfoProvTable	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
atmIfVptPnniAddrPnniInfoProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.10.1		not-accessible	An entry in the atmIfVptPnniAddrPnniInfoProvTable.
INT atmIfVptPnniAddrPnniInfoScope	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT atmIfVptPnniAddrPnniInfoReachability	1.3.6.1.4.1.562.2.4.1.114.9.7.4.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfVptPnniAddrOperTable	1.3.6.1.4.1.562.2.4.1.114.9.7.4.10		not-accessible	This attribute group contains the operational attributes for the Address component.
atmIfVptPnniAddrOperEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.4.10.1		not-accessible	An entry in the atmIfVptPnniAddrOperTable.
INT atmIfVptPnniAddrScope	1.3.6.1.4.1.562.2.4.1.114.9.7.4.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT atmIfVptPnniAddrReachability	1.3.6.1.4.1.562.2.4.1.114.9.7.4.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfVptPnniProvTable	1.3.6.1.4.1.562.2.4.1.114.9.7.10		not-accessible	This group contains the provisionable attributes for the Pnni component.
atmIfVptPnniProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.10.1		not-accessible	An entry in the atmIfVptPnniProvTable.
U32 atmIfVptPnniSoftPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.9.7.10.1.1	Unsigned32	read-write	This attribute represents the time in seconds to wait between call setup retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 atmIfVptPnniSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.9.7.10.1.2	Unsigned32	read-write	This attribute represents the time in seconds to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 atmIfVptPnniSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.2.4.1.114.9.7.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
atmIfVptPnniAdminWeightsTable	1.3.6.1.4.1.562.2.4.1.114.9.7.11		not-accessible	This group contains the provisionable administrative weights for the Pnni component. These weights will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion.
atmIfVptPnniAdminWeightsEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.11.1		not-accessible	An entry in the atmIfVptPnniAdminWeightsTable.
U32 atmIfVptPnniCbrWeight	1.3.6.1.4.1.562.2.4.1.114.9.7.11.1.1	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Constant Bit Rate (CBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
U32 atmIfVptPnniRtVbrWeight	1.3.6.1.4.1.562.2.4.1.114.9.7.11.1.2	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Real-Time Variable Bit Rate (RT-VBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
U32 atmIfVptPnniNrtVbrWeight	1.3.6.1.4.1.562.2.4.1.114.9.7.11.1.3	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Non Real-Time Variable Bit Rate (NRT-VBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
U32 atmIfVptPnniUbrWeight	1.3.6.1.4.1.562.2.4.1.114.9.7.11.1.4	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Unspecified Bit Rate (UBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
atmIfVptPnniAcctOptTable	1.3.6.1.4.1.562.2.4.1.114.9.7.12		not-accessible	This group contains the provisionable attributes for accounting.
atmIfVptPnniAcctOptEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.12.1		not-accessible	An entry in the atmIfVptPnniAcctOptTable.
OCT atmIfVptPnniAccountCollection	1.3.6.1.4.1.562.2.4.1.114.9.7.12.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT atmIfVptPnniAccountConnectionType	1.3.6.1.4.1.562.2.4.1.114.9.7.12.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 atmIfVptPnniAccountClass	1.3.6.1.4.1.562.2.4.1.114.9.7.12.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 atmIfVptPnniServiceExchange	1.3.6.1.4.1.562.2.4.1.114.9.7.12.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
atmIfVptPnniOperationalTable	1.3.6.1.4.1.562.2.4.1.114.9.7.13		not-accessible	This group contains the operational attributes for a Pnni component.
atmIfVptPnniOperationalEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.13.1		not-accessible	An entry in the atmIfVptPnniOperationalTable.
U32 atmIfVptPnniPortId	1.3.6.1.4.1.562.2.4.1.114.9.7.13.1.1	Unsigned32	read-only	This attribute indicates the port id of the PNNI interface, which is the parent AtmIf's instance number.
atmIfVptPnniVProvTable	1.3.6.1.4.1.562.2.4.1.114.9.7.14		not-accessible	This group contains the provisionable attributes for the Pnni component which are specific to virtual PNNI interfaces.
atmIfVptPnniVProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.7.14.1		not-accessible	An entry in the atmIfVptPnniVProvTable.
U32 atmIfVptPnniVpci	1.3.6.1.4.1.562.2.4.1.114.9.7.14.1.1	Unsigned32	read-write	This attribute specifies the Virtual Path Connection Identifier (VPCI) to be used between this signalling entity and its peer. The VPCI of the peer virtual PNNI must have the same value for switched connections to be set up across the interface.
atmIfPnni	1.3.6.1.4.1.562.2.4.1.114.96
atmIfPnniRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.1		not-accessible	This entry controls the addition and deletion of atmIfPnni components.
atmIfPnniRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.1.1		not-accessible	A single entry in the table represents a single atmIfPnni component.
ROW atmIfPnniRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfPnni components. These components can be added and deleted.
STR atmIfPnniComponentName	1.3.6.1.4.1.562.2.4.1.114.96.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniStorageType	1.3.6.1.4.1.562.2.4.1.114.96.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnni tables.
NON atmIfPnniIndex	1.3.6.1.4.1.562.2.4.1.114.96.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfPnni tables.
atmIfPnniSig	1.3.6.1.4.1.562.2.4.1.114.96.2
atmIfPnniSigRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.2.1		not-accessible	This entry controls the addition and deletion of atmIfPnniSig components.
atmIfPnniSigRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.1.1		not-accessible	A single entry in the table represents a single atmIfPnniSig component.
ROW atmIfPnniSigRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfPnniSig components. These components cannot be added nor deleted.
STR atmIfPnniSigComponentName	1.3.6.1.4.1.562.2.4.1.114.96.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniSigStorageType	1.3.6.1.4.1.562.2.4.1.114.96.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnniSig tables.
NON atmIfPnniSigIndex	1.3.6.1.4.1.562.2.4.1.114.96.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfPnniSig tables.
atmIfPnniSigVcd	1.3.6.1.4.1.562.2.4.1.114.96.2.2
atmIfPnniSigVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.2.2.1		not-accessible	This entry controls the addition and deletion of atmIfPnniSigVcd components.
atmIfPnniSigVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.2.1.1		not-accessible	A single entry in the table represents a single atmIfPnniSigVcd component.
ROW atmIfPnniSigVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.2.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfPnniSigVcd components. These components can be added and deleted.
STR atmIfPnniSigVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.96.2.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniSigVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.96.2.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnniSigVcd tables.
NON atmIfPnniSigVcdIndex	1.3.6.1.4.1.562.2.4.1.114.96.2.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfPnniSigVcd tables.
atmIfPnniSigVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfPnniSigVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10.1		not-accessible	An entry in the atmIfPnniSigVcdProvTable.
INT atmIfPnniSigVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfPnniSigVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfPnniSigVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfPnniSigVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfPnniSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfPnniSigVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.96.2.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfPnniSigVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.96.2.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfPnniSigVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.2.387.1		not-accessible	An entry in the atmIfPnniSigVcdTdpTable.
I32 atmIfPnniSigVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.96.2.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfPnniSigVcdTdpTable specific index for the atmIfPnniSigVcdTdpTable.
U32 atmIfPnniSigVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.96.2.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfPnniSigVcdTdpTable.
atmIfPnniSigProvTable	1.3.6.1.4.1.562.2.4.1.114.96.2.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
atmIfPnniSigProvEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.10.1		not-accessible	An entry in the atmIfPnniSigProvTable.
U32 atmIfPnniSigVci	1.3.6.1.4.1.562.2.4.1.114.96.2.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT atmIfPnniSigAddressConversion	1.3.6.1.4.1.562.2.4.1.114.96.2.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
atmIfPnniSigStateTable	1.3.6.1.4.1.562.2.4.1.114.96.2.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfPnniSigStateEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.11.1		not-accessible	An entry in the atmIfPnniSigStateTable.
INT atmIfPnniSigAdminState	1.3.6.1.4.1.562.2.4.1.114.96.2.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfPnniSigOperationalState	1.3.6.1.4.1.562.2.4.1.114.96.2.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfPnniSigUsageState	1.3.6.1.4.1.562.2.4.1.114.96.2.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfPnniSigOperTable	1.3.6.1.4.1.562.2.4.1.114.96.2.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
atmIfPnniSigOperEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.12.1		not-accessible	An entry in the atmIfPnniSigOperTable.
U32 atmIfPnniSigLastTxCauseCode	1.3.6.1.4.1.562.2.4.1.114.96.2.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfPnniSigLastTxDiagCode	1.3.6.1.4.1.562.2.4.1.114.96.2.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 atmIfPnniSigLastRxCauseCode	1.3.6.1.4.1.562.2.4.1.114.96.2.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfPnniSigLastRxDiagCode	1.3.6.1.4.1.562.2.4.1.114.96.2.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
atmIfPnniSigStatsTable	1.3.6.1.4.1.562.2.4.1.114.96.2.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
atmIfPnniSigStatsEntry	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1		not-accessible	An entry in the atmIfPnniSigStatsTable.
C32 atmIfPnniSigCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 atmIfPnniSigPeakConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 atmIfPnniSigSuccessfulConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfPnniSigFailedConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfPnniSigTxPdus	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfPnniSigRxPdus	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfPnniSigCurrentPmpConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 atmIfPnniSigPeakPmpConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 atmIfPnniSigSuccessfulPmpConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfPnniSigFailedPmpConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfPnniSigNewCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.96.2.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
atmIfPnniRcc	1.3.6.1.4.1.562.2.4.1.114.96.3
atmIfPnniRccRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.3.1		not-accessible	This entry controls the addition and deletion of atmIfPnniRcc components.
atmIfPnniRccRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.1.1		not-accessible	A single entry in the table represents a single atmIfPnniRcc component.
ROW atmIfPnniRccRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfPnniRcc components. These components cannot be added nor deleted.
STR atmIfPnniRccComponentName	1.3.6.1.4.1.562.2.4.1.114.96.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniRccStorageType	1.3.6.1.4.1.562.2.4.1.114.96.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnniRcc tables.
NON atmIfPnniRccIndex	1.3.6.1.4.1.562.2.4.1.114.96.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfPnniRcc tables.
atmIfPnniRccVcd	1.3.6.1.4.1.562.2.4.1.114.96.3.2
atmIfPnniRccVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.3.2.1		not-accessible	This entry controls the addition and deletion of atmIfPnniRccVcd components.
atmIfPnniRccVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.2.1.1		not-accessible	A single entry in the table represents a single atmIfPnniRccVcd component.
ROW atmIfPnniRccVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfPnniRccVcd components. These components can be added and deleted.
STR atmIfPnniRccVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.96.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniRccVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.96.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnniRccVcd tables.
NON atmIfPnniRccVcdIndex	1.3.6.1.4.1.562.2.4.1.114.96.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfPnniRccVcd tables.
atmIfPnniRccVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfPnniRccVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10.1		not-accessible	An entry in the atmIfPnniRccVcdProvTable.
INT atmIfPnniRccVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfPnniRccVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfPnniRccVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfPnniRccVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfPnniRccVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfPnniRccVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.96.3.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfPnniRccVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.96.3.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfPnniRccVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.2.387.1		not-accessible	An entry in the atmIfPnniRccVcdTdpTable.
I32 atmIfPnniRccVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.96.3.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfPnniRccVcdTdpTable specific index for the atmIfPnniRccVcdTdpTable.
U32 atmIfPnniRccVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.96.3.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfPnniRccVcdTdpTable.
atmIfPnniRccProvTable	1.3.6.1.4.1.562.2.4.1.114.96.3.10		not-accessible	This group contains the generic provisionable attributes of an Rcc component.
atmIfPnniRccProvEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.10.1		not-accessible	An entry in the atmIfPnniRccProvTable.
U32 atmIfPnniRccVci	1.3.6.1.4.1.562.2.4.1.114.96.3.10.1.1	Unsigned32	read-write	This attribute specifies the VCI for the Routing Control Channel (RCC). It is not recommended that the value be changed from the default of 18 unless absolutely necessary. If a different VCI is specified, ensure that the RCC at the far end is provisioned to use the same VCI, otherwise the RCC will not come up.
atmIfPnniRccHlParmsTable	1.3.6.1.4.1.562.2.4.1.114.96.3.11		not-accessible	This group contains the provisionable Hello protocol parameters for an Rcc component.
atmIfPnniRccHlParmsEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.11.1		not-accessible	An entry in the atmIfPnniRccHlParmsTable.
NUM atmIfPnniRccHelloHoldDown	1.3.6.1.4.1.562.2.4.1.114.96.3.11.1.1	FixedPoint1	read-write	This attribute is used to limit the rate at which this node sends out Hello packets. Specifically, it specifies the minimum time between successive Hellos. A value of 0 specifies that the value provisioned for the helloHoldDown attribute of the ARtg Pnni component should be used.
U32 atmIfPnniRccHelloInterval	1.3.6.1.4.1.562.2.4.1.114.96.3.11.1.2	Unsigned32	read-write	This attribute specifies the duration of the Hello Timer. Every helloInterval seconds, this node will send out a Hello packet to the neighbor node, subject to the helloHoldDown timer having expired at least once since the last Hello packet was sent. A value of 0 specifies that the value provisioned for the helloInterval attribute of the ARtg Pnni component should be used.
U32 atmIfPnniRccHelloInactivityFactor	1.3.6.1.4.1.562.2.4.1.114.96.3.11.1.3	Unsigned32	read-write	This attribute specifies the number of Hello intervals allowed to pass without receiving a Hello from the neighbor node, before an attempt is made to re-stage. The hello inactivity timer is enabled in the oneWayInside, twoWayInside, oneWayOutside, twoWayOutside and commonOutside hello states (see the helloState attribute on the Rcc component for a description of these states). Note that the value for the Hello interval used in the calculation is the one specified in the Hello packet from the neighbor node. A value of 0 specifies that the value provisioned for the helloInactivityFactor attribute of the ARtg Pnni component should be used. DESCRIPTION
atmIfPnniRccStateTable	1.3.6.1.4.1.562.2.4.1.114.96.3.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfPnniRccStateEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.12.1		not-accessible	An entry in the atmIfPnniRccStateTable.
INT atmIfPnniRccAdminState	1.3.6.1.4.1.562.2.4.1.114.96.3.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfPnniRccOperationalState	1.3.6.1.4.1.562.2.4.1.114.96.3.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfPnniRccUsageState	1.3.6.1.4.1.562.2.4.1.114.96.3.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfPnniRccOperTable	1.3.6.1.4.1.562.2.4.1.114.96.3.13		not-accessible	This group contains the operational attributes for an Rcc component.
atmIfPnniRccOperEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.13.1		not-accessible	An entry in the atmIfPnniRccOperTable.
INT atmIfPnniRccType	1.3.6.1.4.1.562.2.4.1.114.96.3.13.1.1	INTEGER	read-only	This attribute indicates the role of this link in the PNNI hierarchy. The following values are possible: unknown: the Hello protocol has not yet determined the role of the link. lowestLevelHorizLink: the link is a horizontal link between two lowest level nodes. lowestLevelOutsideLink: the link is an outside link between two border nodes. horizontalLinkToLgn: the link is a horizontal link to a Logical Group Node (LGN). uplink: the link is a uplink to a higher level LGN.
INT atmIfPnniRccNegotiatedVersion	1.3.6.1.4.1.562.2.4.1.114.96.3.13.1.2	INTEGER	read-only	This attribute indicates the PNNI version negotiated with the neighbor node.
INT atmIfPnniRccHelloState	1.3.6.1.4.1.562.2.4.1.114.96.3.13.1.3	INTEGER	read-only	This attribute indicates the state of the Hello protocol exchange over this link. The following are the possible values for this attribute: down: the link is down; no PNNI routing packets will be sent over or received over such a link. This is the initial state of the Hello Finite State Machine, and can also be reached when lower-level protocols have indicated that the link is not usable. attempt: no Hello packets or Hello packets, with mismatch information, have been received recently from the neighbor. Attempts are made to contact the neighbor node by sending out Hello packets every helloInterval seconds. oneWayInside: Hello packets have been recently received from the neighbor and it has been established that both nodes are members of the same peer group, but the remote node ID and remote port ID in the neighbor's Hello packets were set to zero. A Hello packet is sent to the neighbor and the Hello timer is restarted. twoWayInside: Bidirectional communication over this link between this node and the neighbor node has been achieved. oneWayOutside: Hello packets have been recently received from the neighbor and it has been established that both nodes are members of a different peer group, but the remote node ID and remote port ID in the neighbor's Hello packets were set to zero. twoWayOutside: Hellos have recently been received from the neighbor indicating that the neighbor node belongs to a different peer group. The correct remote node ID and remote port ID fields were included in the Hello packet, but the nodal hierarchy list did not include any common peer group. This state can also be reached if a hierarchy mismatch occurs while in the commonOutside state. commonOutside: A common level of the routing hierarchy has been found, in addition to achieving full bi-directional communication between the two nodes.
STR atmIfPnniRccRemoteNodeId	1.3.6.1.4.1.562.2.4.1.114.96.3.13.1.4	HexString	read-only	This attribute indicates the neighbor node's node id.
U32 atmIfPnniRccRemotePortId	1.3.6.1.4.1.562.2.4.1.114.96.3.13.1.5	Unsigned32	read-only	This attribute indicates the neighbor node's port id.
atmIfPnniRccStatsTable	1.3.6.1.4.1.562.2.4.1.114.96.3.14		not-accessible	This group contains the statistical attributes for an Rcc component.
atmIfPnniRccStatsEntry	1.3.6.1.4.1.562.2.4.1.114.96.3.14.1		not-accessible	An entry in the atmIfPnniRccStatsTable.
C32 atmIfPnniRccHelloPacketsRx	1.3.6.1.4.1.562.2.4.1.114.96.3.14.1.1	Counter32	read-only	This attribute counts the total number of Hello packets received across this RCC, including bad and mismatched Hello packets. The counter wraps when it exceeds the maximum value.
C32 atmIfPnniRccHelloPacketsTx	1.3.6.1.4.1.562.2.4.1.114.96.3.14.1.2	Counter32	read-only	This attribute counts the total number of Hello packets transmitted across this RCC. The counter wraps when it exceeds the maximum value.
C32 atmIfPnniRccMismatchedHelloPacketsRx	1.3.6.1.4.1.562.2.4.1.114.96.3.14.1.3	Counter32	read-only	This attribute counts the total number of mismatched Hello packets received over this RCC. The counter wraps when it exceeds the maximum value.
C32 atmIfPnniRccBadHelloPacketsRx	1.3.6.1.4.1.562.2.4.1.114.96.3.14.1.4	Counter32	read-only	This attribute counts the total number of bad Hello packets received over this RCC. The counter wraps when it exceeds the maximum value.
atmIfPnniAddr	1.3.6.1.4.1.562.2.4.1.114.96.4
atmIfPnniAddrRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.4.1		not-accessible	This entry controls the addition and deletion of atmIfPnniAddr components.
atmIfPnniAddrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.4.1.1		not-accessible	A single entry in the table represents a single atmIfPnniAddr component.
ROW atmIfPnniAddrRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfPnniAddr components. These components can be added and deleted.
STR atmIfPnniAddrComponentName	1.3.6.1.4.1.562.2.4.1.114.96.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniAddrStorageType	1.3.6.1.4.1.562.2.4.1.114.96.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnniAddr tables.
STR atmIfPnniAddrAddressIndex	1.3.6.1.4.1.562.2.4.1.114.96.4.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the atmIfPnniAddr tables.
INT atmIfPnniAddrAddressTypeIndex	1.3.6.1.4.1.562.2.4.1.114.96.4.1.1.11	INTEGER	not-accessible	This variable represents an index for the atmIfPnniAddr tables.
atmIfPnniAddrTermSP	1.3.6.1.4.1.562.2.4.1.114.96.4.2
atmIfPnniAddrTermSPRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.4.2.1		not-accessible	This entry controls the addition and deletion of atmIfPnniAddrTermSP components.
atmIfPnniAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.4.2.1.1		not-accessible	A single entry in the table represents a single atmIfPnniAddrTermSP component.
ROW atmIfPnniAddrTermSPRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfPnniAddrTermSP components. These components can be added and deleted.
STR atmIfPnniAddrTermSPComponentName	1.3.6.1.4.1.562.2.4.1.114.96.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniAddrTermSPStorageType	1.3.6.1.4.1.562.2.4.1.114.96.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnniAddrTermSP tables.
NON atmIfPnniAddrTermSPIndex	1.3.6.1.4.1.562.2.4.1.114.96.4.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfPnniAddrTermSP tables.
atmIfPnniAddrPnniInfo	1.3.6.1.4.1.562.2.4.1.114.96.4.3
atmIfPnniAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.96.4.3.1		not-accessible	This entry controls the addition and deletion of atmIfPnniAddrPnniInfo components.
atmIfPnniAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.96.4.3.1.1		not-accessible	A single entry in the table represents a single atmIfPnniAddrPnniInfo component.
ROW atmIfPnniAddrPnniInfoRowStatus	1.3.6.1.4.1.562.2.4.1.114.96.4.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfPnniAddrPnniInfo components. These components can be added and deleted.
STR atmIfPnniAddrPnniInfoComponentName	1.3.6.1.4.1.562.2.4.1.114.96.4.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfPnniAddrPnniInfoStorageType	1.3.6.1.4.1.562.2.4.1.114.96.4.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfPnniAddrPnniInfo tables.
NON atmIfPnniAddrPnniInfoIndex	1.3.6.1.4.1.562.2.4.1.114.96.4.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfPnniAddrPnniInfo tables.
atmIfPnniAddrPnniInfoProvTable	1.3.6.1.4.1.562.2.4.1.114.96.4.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
atmIfPnniAddrPnniInfoProvEntry	1.3.6.1.4.1.562.2.4.1.114.96.4.3.10.1		not-accessible	An entry in the atmIfPnniAddrPnniInfoProvTable.
INT atmIfPnniAddrPnniInfoScope	1.3.6.1.4.1.562.2.4.1.114.96.4.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT atmIfPnniAddrPnniInfoReachability	1.3.6.1.4.1.562.2.4.1.114.96.4.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfPnniAddrOperTable	1.3.6.1.4.1.562.2.4.1.114.96.4.10		not-accessible	This attribute group contains the operational attributes for the Address component.
atmIfPnniAddrOperEntry	1.3.6.1.4.1.562.2.4.1.114.96.4.10.1		not-accessible	An entry in the atmIfPnniAddrOperTable.
INT atmIfPnniAddrScope	1.3.6.1.4.1.562.2.4.1.114.96.4.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT atmIfPnniAddrReachability	1.3.6.1.4.1.562.2.4.1.114.96.4.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfPnniProvTable	1.3.6.1.4.1.562.2.4.1.114.96.10		not-accessible	This group contains the provisionable attributes for the Pnni component.
atmIfPnniProvEntry	1.3.6.1.4.1.562.2.4.1.114.96.10.1		not-accessible	An entry in the atmIfPnniProvTable.
U32 atmIfPnniSoftPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.96.10.1.1	Unsigned32	read-write	This attribute represents the time in seconds to wait between call setup retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 atmIfPnniSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.96.10.1.2	Unsigned32	read-write	This attribute represents the time in seconds to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 atmIfPnniSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.2.4.1.114.96.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
atmIfPnniAdminWeightsTable	1.3.6.1.4.1.562.2.4.1.114.96.11		not-accessible	This group contains the provisionable administrative weights for the Pnni component. These weights will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion.
atmIfPnniAdminWeightsEntry	1.3.6.1.4.1.562.2.4.1.114.96.11.1		not-accessible	An entry in the atmIfPnniAdminWeightsTable.
U32 atmIfPnniCbrWeight	1.3.6.1.4.1.562.2.4.1.114.96.11.1.1	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Constant Bit Rate (CBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
U32 atmIfPnniRtVbrWeight	1.3.6.1.4.1.562.2.4.1.114.96.11.1.2	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Real-Time Variable Bit Rate (RT-VBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
U32 atmIfPnniNrtVbrWeight	1.3.6.1.4.1.562.2.4.1.114.96.11.1.3	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Non Real-Time Variable Bit Rate (NRT-VBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
U32 atmIfPnniUbrWeight	1.3.6.1.4.1.562.2.4.1.114.96.11.1.4	Unsigned32	read-write	This attribute specifies the administrative weight assigned for setting up switched calls with a service category of Unspecified Bit Rate (UBR) for this PNNI interface. The value specified will be used by Generic Connection Admission Control (GCAC) if administrative weight is the selected optimization criterion; the higher the value, the less desirable the link will be in path selection.
atmIfPnniAcctOptTable	1.3.6.1.4.1.562.2.4.1.114.96.12		not-accessible	This group contains the provisionable attributes for accounting.
atmIfPnniAcctOptEntry	1.3.6.1.4.1.562.2.4.1.114.96.12.1		not-accessible	An entry in the atmIfPnniAcctOptTable.
OCT atmIfPnniAccountCollection	1.3.6.1.4.1.562.2.4.1.114.96.12.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT atmIfPnniAccountConnectionType	1.3.6.1.4.1.562.2.4.1.114.96.12.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 atmIfPnniAccountClass	1.3.6.1.4.1.562.2.4.1.114.96.12.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 atmIfPnniServiceExchange	1.3.6.1.4.1.562.2.4.1.114.96.12.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
atmIfPnniOperationalTable	1.3.6.1.4.1.562.2.4.1.114.96.13		not-accessible	This group contains the operational attributes for a Pnni component.
atmIfPnniOperationalEntry	1.3.6.1.4.1.562.2.4.1.114.96.13.1		not-accessible	An entry in the atmIfPnniOperationalTable.
U32 atmIfPnniPortId	1.3.6.1.4.1.562.2.4.1.114.96.13.1.1	Unsigned32	read-only	This attribute indicates the port id of the PNNI interface, which is the parent AtmIf's instance number.
atmPnniMIB	1.3.6.1.4.1.562.2.4.2.72
atmPnniGroup	1.3.6.1.4.1.562.2.4.2.72.1
atmPnniGroupBE	1.3.6.1.4.1.562.2.4.2.72.1.5
atmPnniGroupBE00	1.3.6.1.4.1.562.2.4.2.72.1.5.1
atmPnniGroupBE00A	1.3.6.1.4.1.562.2.4.2.72.1.5.1.2
atmPnniCapabilities	1.3.6.1.4.1.562.2.4.2.72.3
atmPnniCapabilitiesBE	1.3.6.1.4.1.562.2.4.2.72.3.5
atmPnniCapabilitiesBE00	1.3.6.1.4.1.562.2.4.2.72.3.5.1
atmPnniCapabilitiesBE00A	1.3.6.1.4.1.562.2.4.2.72.3.5.1.2

RFC description

ATM Private Network-Network Interface (PNNI) management for Nortel Magellan Passport systems.

Start monitoring Nortel Magellan Passport ATM switch (PNNI routing) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-Magellan-Passport-AtmPnniMIB

What Is Nortel-Magellan-Passport-AtmPnniMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description