POWERHUB-TCPIP-MIB

All MIBs › POWERHUB-TCPIP-MIB

Category: Switching

Description: Manages TCP/IP stack configuration and routing table entries on the 3Com PowerHub Ethernet switching platform.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is POWERHUB-TCPIP-MIB?

POWERHUB-TCPIP-MIB manages TCP/IP stack configuration and IP routing table entries on the 3Com PowerHub Ethernet switching platform. It exposes network-layer configuration data such as IP addressing and routing table entries rather than physical hardware sensors. Its monitoring value is primarily around software/protocol state: confirming the device's IP stack configuration is correct and that its routing table reflects the expected topology, which indirectly signals whether the switch's control-plane software is operating correctly. It parallels concepts found in the standard IP-MIB and IP-FORWARD-MIB for routing table representation, suggesting conceptual dependency on those IETF standards. It is deployed alongside POWERHUB-CORE-MIB in legacy 3Com PowerHub chassis switch installations that route as well as switch traffic. Engineers can download the POWERHUB-TCPIP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in POWERHUB-TCPIP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

3Com PowerHub chassis switch

Monitoring Examples

No sample_objects were provided in the source, so specific object or table names cannot be cited; in general an admin would poll the routing table entries to verify expected routes are present and IP configuration objects to confirm addressing is correct. A missing expected route or an unexpected default route change would be a realistic anomaly this MIB could reveal. This remains a general description pending concrete identifiers.

Imported Objects

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
OBJECT-TYPE
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
fore	1.3.6.1.4.1.326
systems	1.3.6.1.4.1.326.2
lsd	1.3.6.1.4.1.326.2.6
lsdproducts	1.3.6.1.4.1.326.2.6.1
lsdcommon	1.3.6.1.4.1.326.2.6.2
alrip	1.3.6.1.4.1.326.2.6.2.4
INT alripControlType	1.3.6.1.4.1.326.2.6.2.4.1	INTEGER	read-write	control type to change the RIP update mechanism
alRipNormalConfigTable	1.3.6.1.4.1.326.2.6.2.4.2		not-accessible	Per port RIP configuration per segment method.
alripNormalConfigEntry	1.3.6.1.4.1.326.2.6.2.4.2.1		not-accessible	information about a specific RIP configuration entry
INT alripNormalConfigPort	1.3.6.1.4.1.326.2.6.2.4.2.1.1	INTEGER	read-write	Port number for which the RIP parameters are to be set or viewed.
INT alripNormalConfigTalk	1.3.6.1.4.1.326.2.6.2.4.2.1.2	INTEGER	read-write	Controls whether the hub generates RIP packets on the port identified by the instance of ripConfigPort.
INT alripNormalConfigListen	1.3.6.1.4.1.326.2.6.2.4.2.1.3	INTEGER	read-write	Controls whether the hub processes RIP packets received on the port identified by the instance of ripConfigPort.
INT alripNormalConfigPoison	1.3.6.1.4.1.326.2.6.2.4.2.1.4	INTEGER	read-write	Controls what happens when a route goes down. If set to no(2), the hub simply stops reporting the route. If set to yes(1), the hub reports it one more time, but with a metric value of 16, which infinity as far as RIP is concerned. Thus other routers learn immediately that the route is down.
INT alripNormalConfigRptStaticRt	1.3.6.1.4.1.326.2.6.2.4.2.1.5	INTEGER	read-write	When RIP packets are generated on the port, controls whether the hub reports the static routes in its route table.
INT alripNormalConfigRptDefaultRt	1.3.6.1.4.1.326.2.6.2.4.2.1.6	INTEGER	read-write	When RIP packets are generated on the port, controls whether the hub reports the default routes, if any, in ints route table.
INT alripNormalConfigAccptDefaultRt	1.3.6.1.4.1.326.2.6.2.4.2.1.7	INTEGER	read-write	When RIP packets are received on the port, controls whether the hub accepts(learns) a default route that is reported in a RIP packet.
alRipVLANConfigTable	1.3.6.1.4.1.326.2.6.2.4.3		not-accessible	Per port RIP configuration per VLAN method.
alripVLANConfigEntry	1.3.6.1.4.1.326.2.6.2.4.3.1		not-accessible	information about a specific RIP configuration entry
IP alripVLANConfigNetNumber	1.3.6.1.4.1.326.2.6.2.4.3.1.1	IpAddress	read-write	IP network number for which the RIP parameters are to be set or viewed.
INT alripVLANConfigTalk	1.3.6.1.4.1.326.2.6.2.4.3.1.2	INTEGER	read-write	Controls whether the hub generates RIP packets on the port identified by the instance of ripConfigPort.
INT alripVLANConfigListen	1.3.6.1.4.1.326.2.6.2.4.3.1.3	INTEGER	read-write	Controls whether the hub processes RIP packets received on the port identified by the instance of ripConfigPort. This field cannot be activated if this interface is controlled by OSPF
INT alripVLANConfigPoison	1.3.6.1.4.1.326.2.6.2.4.3.1.4	INTEGER	read-write	Controls what happens when a route goes down. If set to no(2), the hub simply stops reporting the route. If set to yes(1), the hub reports it one more time, but with a metric value of 16, which infinity as far as RIP is concerned. Thus other routers learn immediately that the route is down.
INT alripVLANConfigRptStaticRt	1.3.6.1.4.1.326.2.6.2.4.3.1.5	INTEGER	read-write	When RIP packets are generated on the port, controls whether the hub reports the static routes in its route table.
INT alripVLANConfigRptDefaultRt	1.3.6.1.4.1.326.2.6.2.4.3.1.6	INTEGER	read-write	When RIP packets are generated on the port, controls whether the hub reports the default routes, if any, in ints route table.
INT alripVLANConfigAccptDefaultRt	1.3.6.1.4.1.326.2.6.2.4.3.1.7	INTEGER	read-write	When RIP packets are received on the port, controls whether the hub accepts(learns) a default
INT alripVLANConfigDelete	1.3.6.1.4.1.326.2.6.2.4.3.1.8	INTEGER	read-write	When set to 1, this entry is deleted.
INT alripStatsClear	1.3.6.1.4.1.326.2.6.2.4.4	INTEGER	read-write	When set to 1, clears the RIP stats
CTR alRipStatPktsRcvd	1.3.6.1.4.1.326.2.6.2.4.5	Counter	read-only	Packets Received.
CTR alRipStatPktsXmitted	1.3.6.1.4.1.326.2.6.2.4.6	Counter	read-only	Packets Sent.
CTR alRipStatReqsRcvd	1.3.6.1.4.1.326.2.6.2.4.7	Counter	read-only	Requests Received.
CTR alRipStatRespRcvd	1.3.6.1.4.1.326.2.6.2.4.8	Counter	read-only	Responses Received.
CTR alRipStatReqsXmitted	1.3.6.1.4.1.326.2.6.2.4.9	Counter	read-only	Requests Sent.
CTR alRipStatRespXmitted	1.3.6.1.4.1.326.2.6.2.4.10	Counter	read-only	Responses Sent.
CTR alRipStatRouteTimeOuts	1.3.6.1.4.1.326.2.6.2.4.11	Counter	read-only	Route Timeouts.
CTR alRipStatShortPkts	1.3.6.1.4.1.326.2.6.2.4.12	Counter	read-only	Short packets received.
CTR alRipStatBadVer	1.3.6.1.4.1.326.2.6.2.4.13	Counter	read-only	Bad version pkts received.
CTR alRipStatBadZeroes	1.3.6.1.4.1.326.2.6.2.4.14	Counter	read-only	Bad zeroes received.
CTR alRipStatBadSrcPort	1.3.6.1.4.1.326.2.6.2.4.15	Counter	read-only	Packets with bad Source port received.
CTR alRipStatBadSrcIp	1.3.6.1.4.1.326.2.6.2.4.16	Counter	read-only	Packets with bad source IP address received.
CTR alRipStatPktsSelf	1.3.6.1.4.1.326.2.6.2.4.17	Counter	read-only	Packets from self received.
CTR alRipigUpdates	1.3.6.1.4.1.326.2.6.2.4.18	Counter	read-only	number of RIP update trigged.
CTR alRipStatPqueuePktsQueued	1.3.6.1.4.1.326.2.6.2.4.19	Counter	read-only	Packets queued in RIP process queue.
CTR alRipStatPqueueFreeQueue	1.3.6.1.4.1.326.2.6.2.4.20	Counter	read-only	Free entries in the RIP processing queue.
CTR alRipStatTqueuePktsQueued	1.3.6.1.4.1.326.2.6.2.4.21	Counter	read-only	Packets queued in the RIP route timeout process queue.
CTR alRipStatTqueueFreeQueue	1.3.6.1.4.1.326.2.6.2.4.22	Counter	read-only	Free entries in the RIP route timeout queue.
CTR alRipDynPktsRcvd	1.3.6.1.4.1.326.2.6.2.4.23	Counter	read-only	Packets Received.
CTR alRipDynPktsXmitted	1.3.6.1.4.1.326.2.6.2.4.24	Counter	read-only	Packets Sent.
CTR alRipDynReqsRcvd	1.3.6.1.4.1.326.2.6.2.4.25	Counter	read-only	Requests Received.
CTR alRipDynRespRcvd	1.3.6.1.4.1.326.2.6.2.4.26	Counter	read-only	Responses Received.
CTR alRipDynReqsXmitted	1.3.6.1.4.1.326.2.6.2.4.27	Counter	read-only	Requests Sent.
CTR alRipDynRespXmitted	1.3.6.1.4.1.326.2.6.2.4.28	Counter	read-only	Responses Sent.
CTR alRipDynRouteTimeOuts	1.3.6.1.4.1.326.2.6.2.4.29	Counter	read-only	Route Timeouts.
CTR alRipDynShortPkts	1.3.6.1.4.1.326.2.6.2.4.30	Counter	read-only	Short packets received.
CTR alRipDynBadVer	1.3.6.1.4.1.326.2.6.2.4.31	Counter	read-only	Bad version pkts received.
CTR alRipDynBadZeroes	1.3.6.1.4.1.326.2.6.2.4.32	Counter	read-only	Bad zeroes received.
CTR alRipDynBadSrcPort	1.3.6.1.4.1.326.2.6.2.4.33	Counter	read-only	Packets with bad Source port received.
CTR alRipDynBadSrcIp	1.3.6.1.4.1.326.2.6.2.4.34	Counter	read-only	Packets with bad source IP address received.
CTR alRipDynPktsSelf	1.3.6.1.4.1.326.2.6.2.4.35	Counter	read-only	Packets from self received.
CTR alRipDynNumTrigUpdates	1.3.6.1.4.1.326.2.6.2.4.36	Counter	read-only	number of RIP update trigged.
CTR alRipDyntPqueuePktsQueued	1.3.6.1.4.1.326.2.6.2.4.37	Counter	read-only	Packets queued in RIP process queue.
CTR alRipDynPqueueFreeQueue	1.3.6.1.4.1.326.2.6.2.4.38	Counter	read-only	Free entries in the RIP processing queue.
CTR alRipDynTqueuePktsQueued	1.3.6.1.4.1.326.2.6.2.4.39	Counter	read-only	Packets queued in the RIP route timeout process queue.
CTR alRipDynTqueueFreeQueue	1.3.6.1.4.1.326.2.6.2.4.40	Counter	read-only	Free entries in the RIP route timeout queue.
alRipAccptFilTable	1.3.6.1.4.1.326.2.6.2.4.41		not-accessible	RIP Accept filter table
ripAccptFilEntry	1.3.6.1.4.1.326.2.6.2.4.41.1		not-accessible	RIP Accept filter entry
INT ripAccptFilNumber	1.3.6.1.4.1.326.2.6.2.4.41.1.1	INTEGER	read-write	Filter Number; Range 1-64
IP ripAccptFilAddr	1.3.6.1.4.1.326.2.6.2.4.41.1.2	IpAddress	read-write	Valid network or subnet address
IP ripAccptFilMask	1.3.6.1.4.1.326.2.6.2.4.41.1.3	IpAddress	read-write	Accept filter Mask
INT ripAccptFilPort	1.3.6.1.4.1.326.2.6.2.4.41.1.4	INTEGER	read-write	Port number on which network should be accepted or not. Range 1-14.
alRipReportFilTable	1.3.6.1.4.1.326.2.6.2.4.42		not-accessible	RIP Report filter table
ripReportFilEntry	1.3.6.1.4.1.326.2.6.2.4.42.1		not-accessible	RIP Report filter entry
INT ripReportFilNumber	1.3.6.1.4.1.326.2.6.2.4.42.1.1	INTEGER	read-write	Filter Number; Range 1-64
IP ripReportFilAddr	1.3.6.1.4.1.326.2.6.2.4.42.1.2	IpAddress	read-write	Valid network or subnet address
IP ripReportFilMask	1.3.6.1.4.1.326.2.6.2.4.42.1.3	IpAddress	read-write	Report filter Mask
INT ripReportFilPort	1.3.6.1.4.1.326.2.6.2.4.42.1.4	INTEGER	read-write	Port number on which network should be reported or not. Port number range 1-14
altcp	1.3.6.1.4.1.326.2.6.2.5
INT alTcpConnIdleTime	1.3.6.1.4.1.326.2.6.2.5.1	INTEGER	read-write	Time in minutes before sending keep-alives. The range is 5 to 30 minutes.
INT alTcpKeepAliveInt	1.3.6.1.4.1.326.2.6.2.5.2	INTEGER	read-write	Time interval in seconds between two successive keep-alive sends. The range is 30 to 240 seconds.
INT alTcpDisconnectInt	1.3.6.1.4.1.326.2.6.2.5.3	INTEGER	read-only	Time interval in seconds, before an idle connection is dropped. This equals to the sum of alTcpConnIdleTime plus eight times the alTcpKeepAliveInt interval.
INT alTcpShortSegRcvd	1.3.6.1.4.1.326.2.6.2.5.4	INTEGER	read-only	Number of short segments received.
INT alTcpStatsClear	1.3.6.1.4.1.326.2.6.2.5.5	INTEGER	read-write	When set to 1, clears the TCP stats.
alTcpConnTable	1.3.6.1.4.1.326.2.6.2.5.6		not-accessible	A table containing TCP connection-specific information.
alTcpConnEntry	1.3.6.1.4.1.326.2.6.2.5.6.1		not-accessible	Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state.
INT alTcpConnId	1.3.6.1.4.1.326.2.6.2.5.6.1.1	INTEGER	read-only	The connection Identifier by which a connection is addressed.
INT alTcpConnState	1.3.6.1.4.1.326.2.6.2.5.6.1.2	INTEGER	read-write	The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection.
IP alTcpConnLocalAddress	1.3.6.1.4.1.326.2.6.2.5.6.1.3	IpAddress	read-only	The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used.
INT alTcpConnLocalPort	1.3.6.1.4.1.326.2.6.2.5.6.1.4	INTEGER	read-only	The local port number for this TCP connection.
IP alTcpConnRemAddress	1.3.6.1.4.1.326.2.6.2.5.6.1.5	IpAddress	read-only	The remote IP address for this TCP connection.
INT alTcpConnRemPort	1.3.6.1.4.1.326.2.6.2.5.6.1.6	INTEGER	read-only	The remote port number for this TCP connection.
alTcpFilTable	1.3.6.1.4.1.326.2.6.2.5.7		not-accessible	TCP filter table
tcpFilEntry	1.3.6.1.4.1.326.2.6.2.5.7.1		not-accessible	TCP filter entry
INT tcpFilNumber	1.3.6.1.4.1.326.2.6.2.5.7.1.1	INTEGER	read-write	Filter Number; Range 1-32
IP tcpFilSrcAddr	1.3.6.1.4.1.326.2.6.2.5.7.1.2	IpAddress	read-write	Source address
IP tcpFilSrcMask	1.3.6.1.4.1.326.2.6.2.5.7.1.3	IpAddress	read-write	Mask
INT tcpFilProtocol	1.3.6.1.4.1.326.2.6.2.5.7.1.4	INTEGER	read-write	tcp(1) or udp(2)
INT tcpFilDstPort	1.3.6.1.4.1.326.2.6.2.5.7.1.5	INTEGER	read-write	smtp(1000), telnet(2000), ftp(3000) or valid port Number
alip	1.3.6.1.4.1.326.2.6.2.6
INT alArpTableClear	1.3.6.1.4.1.326.2.6.2.6.1	INTEGER	read-write	When set, clears the ARP table.
INT alArpAge	1.3.6.1.4.1.326.2.6.2.6.2	INTEGER	read-write	Timeout in minutes for aging ARP entries; when set to zero, set-arpage is turned off.
CTR alArpStatReqsRcvd	1.3.6.1.4.1.326.2.6.2.6.3	Counter	read-only	Requests Received.
CTR alArpStatRepliesRcvd	1.3.6.1.4.1.326.2.6.2.6.4	Counter	read-only	Replies Received.
CTR alArpStatInvalidOpcodes	1.3.6.1.4.1.326.2.6.2.6.5	Counter	read-only	Invalid Opcodes Received.
CTR alArpStatRequestsSent	1.3.6.1.4.1.326.2.6.2.6.6	Counter	read-only	Requests Sent.
CTR alArpStatRepliesSent	1.3.6.1.4.1.326.2.6.2.6.7	Counter	read-only	Replies Sent.
CTR alArpStatProxyReplies	1.3.6.1.4.1.326.2.6.2.6.8	Counter	read-only	number of proxy replied
CTR alArpDynReqsRcvd	1.3.6.1.4.1.326.2.6.2.6.9	Counter	read-only	Requests Received.
CTR alArpDynRepliesRcvd	1.3.6.1.4.1.326.2.6.2.6.10	Counter	read-only	Replies Received.
CTR alArpDynInvalidOpcodes	1.3.6.1.4.1.326.2.6.2.6.11	Counter	read-only	Invalid Opcodes Received.
CTR alArpDynRequestsSent	1.3.6.1.4.1.326.2.6.2.6.12	Counter	read-only	Requests Sent.
CTR alArpDynRepliesSent	1.3.6.1.4.1.326.2.6.2.6.13	Counter	read-only	Replies Sent.
CTR alArpDynProxyReplies	1.3.6.1.4.1.326.2.6.2.6.14	Counter	read-only	number of proxy replied
INT alArpStatsClear	1.3.6.1.4.1.326.2.6.2.6.15	INTEGER	read-write	When set to 1, clears the ARP statistics.
alArpProxyTable	1.3.6.1.4.1.326.2.6.2.6.16		not-accessible	Per port proxy arp enable/disable
arpProxyEntry	1.3.6.1.4.1.326.2.6.2.6.16.1		not-accessible	information of a specific arp proxy entry
INT arpProxyPort	1.3.6.1.4.1.326.2.6.2.6.16.1.1	INTEGER	read-only	Port Number
INT arpProxyEnable	1.3.6.1.4.1.326.2.6.2.6.16.1.2	INTEGER	read-write	If set to Enable(1), enables proxy arp arp requests received on the port identified by the instance of arpProxyPort. If set to Disable(2), it disables the proxy arp for arp requests received on the ports identified by the instance of arpProxyPort.
alIpTemplateTable	1.3.6.1.4.1.326.2.6.2.6.17		not-accessible	Per template information
alipTemplateEntry	1.3.6.1.4.1.326.2.6.2.6.17.1		not-accessible	Information about a filtering template
INT alipTemplateNumber	1.3.6.1.4.1.326.2.6.2.6.17.1.1	INTEGER	read-write	The number of the template with which it is identified.
INT alipTemplateDelete	1.3.6.1.4.1.326.2.6.2.6.17.1.2	INTEGER	read-write	When set to 1, this entry is deleted.
INT alipTemplateAction	1.3.6.1.4.1.326.2.6.2.6.17.1.3	INTEGER	read-write	Whether the packet being filtered should be forwarded or blocked
IP alipTemplateSrcAddr	1.3.6.1.4.1.326.2.6.2.6.17.1.4	IpAddress	read-write	The portion of the packet's source address specified by ipTemplateSrcMask is matched with this address.
IP alipTemplateSrcMask	1.3.6.1.4.1.326.2.6.2.6.17.1.5	IpAddress	read-write	Source Mask. The portion specified by this mask is matched with source address.
IP alipTemplateDstAddr	1.3.6.1.4.1.326.2.6.2.6.17.1.6	IpAddress	read-write	The portion of the packet's destination address specified by ipTemplateDstMask is matched with this address.
IP alipTemplateDstMask	1.3.6.1.4.1.326.2.6.2.6.17.1.7	IpAddress	read-write	Destination mask. The portion specified by this mask is matched with destination address.
INT alipTemplateProtocol	1.3.6.1.4.1.326.2.6.2.6.17.1.8	INTEGER	read-write	Determines the type of packets that need to be filtered. PowerHub currently recognizes ip(1) , icmp(1), ipinip(4), tcp(6), udp(17), ospf(89). If all(0) is specified, the filter looks for all protocols other than the ones PowerHub currently accepts. The IP protocol numbers are listed in RFC 1340
INT alipTemplateOperator	1.3.6.1.4.1.326.2.6.2.6.17.1.9	INTEGER	read-write	Allowed only if the protocol field is tcp or udp. The following operators allowed: (1) Unknown =(2) Equal to ~=(3) Not equal to (5) Greater than conreq(6) Connect request. Connect request is valid only if protocol is tcp
INT alipTemplateDstPort	1.3.6.1.4.1.326.2.6.2.6.17.1.10	INTEGER	read-write	This is expressed as either a well-known protocol name or a well-known tcp or udp port number. 0 means unknown
alIpRuleTable	1.3.6.1.4.1.326.2.6.2.6.18		not-accessible	Per template information
alipRuleEntry	1.3.6.1.4.1.326.2.6.2.6.18.1		not-accessible	Information about a specific filtering rule
INT alipRuleNumber	1.3.6.1.4.1.326.2.6.2.6.18.1.1	INTEGER	read-write	The number of the rule with which it is Identified.
INT alipRuleDelete	1.3.6.1.4.1.326.2.6.2.6.18.1.2	INTEGER	read-write	If set to 1 the entry is deleted.
STR alipRuleTemplates	1.3.6.1.4.1.326.2.6.2.6.18.1.3	DisplayString	read-write	The templates associated with the rule identified by the instance of ipRuleNumber.
alipAcsCtrlTable	1.3.6.1.4.1.326.2.6.2.6.19		not-accessible	Per port IP access control filters
alipAcsCtrlEntry	1.3.6.1.4.1.326.2.6.2.6.19.1		not-accessible	information of a specific rule applied to segment
INT alipAcsCtrlPort	1.3.6.1.4.1.326.2.6.2.6.19.1.1	INTEGER	read-write	Port number of the port for which the source and destination access filter apply.
INT alipAcsCtrlDelete	1.3.6.1.4.1.326.2.6.2.6.19.1.2	INTEGER	read-write	If set to 1, the entry is deleted.
INT alipAcsCtrlSourceRule	1.3.6.1.4.1.326.2.6.2.6.19.1.3	INTEGER	read-write	the source rule is assigned to the segment
INT alipAcsCtrlDestRule	1.3.6.1.4.1.326.2.6.2.6.19.1.4	INTEGER	read-write	the destination rule is assigned to the segment
alipFilStatStatsTable	1.3.6.1.4.1.326.2.6.2.6.20		not-accessible	Per template static statistics -- stats from the beginning of the last system reboot.
alipFilStatStatsEntry	1.3.6.1.4.1.326.2.6.2.6.20.1		not-accessible	filter statistics entry
CTR alipFilStatStatsTemplate	1.3.6.1.4.1.326.2.6.2.6.20.1.1	Counter	read-only	The template number for which the stats are displayed
CTR alipFilStatStatsInPkts	1.3.6.1.4.1.326.2.6.2.6.20.1.2	Counter	read-only	The number of packets that matched the template identified by the instance of alipFilStatStatsTemplate. The template has to be a Source template.
CTR alipFilStatStatsOutPkts	1.3.6.1.4.1.326.2.6.2.6.20.1.3	Counter	read-only	The number of packets that matched the template identified by the instance of alipFilStatStatsTemplate. The template has to be a Destination template.
alipFilDynStatsTable	1.3.6.1.4.1.326.2.6.2.6.21		not-accessible	Per template dynamic statistics -- stats from the beginning of the last clear.
alipFilDynStatsEntry	1.3.6.1.4.1.326.2.6.2.6.21.1		not-accessible	information of a specific statistic entry
CTR alipFilDynStatsTemplate	1.3.6.1.4.1.326.2.6.2.6.21.1.1	Counter	read-only	The template number for which the stats are displayed
CTR alipFilDynStatsInPkts	1.3.6.1.4.1.326.2.6.2.6.21.1.2	Counter	read-only	The number of packets that matched the template identified by the instance of alipFilDynStatsTemplate. The template has to be a Source template.
CTR alipFilDynStatsOutPkts	1.3.6.1.4.1.326.2.6.2.6.21.1.3	Counter	read-only	The number of packets that matched the template identified by the instance of alipFilDynStatsTemplate. The template has to be a Destination template.
INT alipFilDynStatsClear	1.3.6.1.4.1.326.2.6.2.6.21.1.4	INTEGER	write-only	Setting the value of 1, it will clear all the stats for the template identified by the instance of alipFilDynStatsTemplate.
CTR alipTotalFilPacketForward	1.3.6.1.4.1.326.2.6.2.6.22	Counter	read-only	The total number of packets forwarded since last system reset.
CTR alipTotalFilPacketBlock	1.3.6.1.4.1.326.2.6.2.6.23	Counter	read-only	The total number of packets blocked since last system reset.
CTR alipCurrentFilPacketForward	1.3.6.1.4.1.326.2.6.2.6.24	Counter	read-only	The total number of packets forwarded since the last statistical clear.
CTR alipCurrentFilPacketBlock	1.3.6.1.4.1.326.2.6.2.6.25	Counter	read-only	The total number of packets blocked since the last statistical clear.
alIpInterfaceTable	1.3.6.1.4.1.326.2.6.2.6.26		not-accessible	IP interface table corresponding to the command - interface-table.
alIpInterfaceEntry	1.3.6.1.4.1.326.2.6.2.6.26.1		not-accessible	Entry of IP interface
INT ipInterfaceNumber	1.3.6.1.4.1.326.2.6.2.6.26.1.1	INTEGER	read-write	Segment number of the selecetd IP address interface entry.
IP ipInterfaceAddress	1.3.6.1.4.1.326.2.6.2.6.26.1.2	IpAddress	read-write	IP address of the selected IP segment number.
IP ipInterfaceSubnetMask	1.3.6.1.4.1.326.2.6.2.6.26.1.3	IpAddress	read-write	IP subnet mask for the selected IP address.
INT ipInterfaceBroadCast	1.3.6.1.4.1.326.2.6.2.6.26.1.4	INTEGER	read-write	Specifies style of broadcast address on a segment basis: when you specify 'br0', the hub sends an 'all-0s' broadcast; when you sepcify 'br1', the hub sends 'all-1s' broadcast. The default is 'br1'.
INT ipInterfaceCost	1.3.6.1.4.1.326.2.6.2.6.26.1.5	INTEGER	read-write	Specifies an additiopnal cost of using the subnet interface. This cost is the number of extra hops to the destination. The range is 1 thru 14. The default is 0. When you set the cost to a value greater than zero, routing is forced thru the other hub if it is alive.
INT ipInterfaceDelete	1.3.6.1.4.1.326.2.6.2.6.26.1.6	INTEGER	read-write	When this object is set with value 1, the IP interface corresponds to the segment number will be deleted; otherwise this object returns value 0.
INT ipInterfaceMtu	1.3.6.1.4.1.326.2.6.2.6.26.1.7	INTEGER	read-only	Displays the maximum transimission unit size allowed on this IP interface.
INT ipInterfaceState	1.3.6.1.4.1.326.2.6.2.6.26.1.8	INTEGER	read-only	Displays the up/down status of the IP interface.
CTR ipInterfacePktsIn	1.3.6.1.4.1.326.2.6.2.6.26.1.9	Counter	read-only	Total number of packets received on this interface.
CTR ipInterfaceOctetsIn	1.3.6.1.4.1.326.2.6.2.6.26.1.10	Counter	read-only	Total number of bytes received on this interface.
CTR ipInterfacePktsOut	1.3.6.1.4.1.326.2.6.2.6.26.1.11	Counter	read-only	Total number of packets transmitted to the network by this interface.
CTR ipInterfaceOctetsOut	1.3.6.1.4.1.326.2.6.2.6.26.1.12	Counter	read-only	Total number of bytes transimitted to the network by this interface.
alIpRtCacheTable	1.3.6.1.4.1.326.2.6.2.6.27		not-accessible	IP Route Cache for all ports
alIpRtCacheEntry	1.3.6.1.4.1.326.2.6.2.6.27.1		not-accessible	IP Route cache for each port
INT ipRtCachePort	1.3.6.1.4.1.326.2.6.2.6.27.1.1	INTEGER	read-write	Port number for the ip route cache.
INT ipRtCacheDstAddress	1.3.6.1.4.1.326.2.6.2.6.27.1.2	INTEGER	read-write	Ip route cache destination address.
INT ipRtCacheClear	1.3.6.1.4.1.326.2.6.2.6.27.1.3	INTEGER	write-only	Setting this to Clear(1), will clear the routecache for the port and Destination address identified by the instance of ipRtCachePort and ipRtCacheDstAddress.
alVlanIpInterfaceTable	1.3.6.1.4.1.326.2.6.2.6.28		not-accessible	Vlan IP interface table corresponding to the command - vlan add/del IP interface.
alVlanIpInterfaceEntry	1.3.6.1.4.1.326.2.6.2.6.28.1		not-accessible	Entry of Vlan IP interface
INT vlanIpInterfaceNameLen	1.3.6.1.4.1.326.2.6.2.6.28.1.1	INTEGER	read-only	The string length of Vlan name of the selecetd vlan IP interface entry.
STR vlanIpInterfaceName	1.3.6.1.4.1.326.2.6.2.6.28.1.2	DisplayString	read-only	Vlan name of the selecetd vlan IP interface entry.
IP vlanIpInterfaceAddress	1.3.6.1.4.1.326.2.6.2.6.28.1.3	IpAddress	read-only	IP address of the selected vlan IP interface entry.
IP vlanIpInterfaceSubnetMask	1.3.6.1.4.1.326.2.6.2.6.28.1.4	IpAddress	read-write	IP subnet mask for the selected vlan IP interface entry.
INT vlanIpInterfaceType	1.3.6.1.4.1.326.2.6.2.6.28.1.5	INTEGER	read-write	Specifies type of interface of vlan The types are are broadcast, nbma (nonBroadcastMultiAccess i.e.,CLIP), ptop (i.e.,PVC). Default is broadcast. The discontinuos enumeration values actually mean bitmask value which maps to bit positions in the agent.
IP vlanIpInterfaceNeighborAddress	1.3.6.1.4.1.326.2.6.2.6.28.1.6	IpAddress	read-write	Specifies the ip address of neightbors of the interfaces of the vlan. This object apply only when interface type is pointToPoint.
INT vlanIpInterfaceRowStatus	1.3.6.1.4.1.326.2.6.2.6.28.1.7	INTEGER	read-write	The status of the table. The table can not be changed when it is active.

RFC description

Vendor-private MIB for Fore Systems PowerHub ATM switching platform defining TCP/IP protocol configuration and statistics.

Start monitoring 3Com PowerHub chassis switch (TCP/IP stack/routing configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download POWERHUB-TCPIP-MIB

What Is POWERHUB-TCPIP-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description