All MIBs › POWERHUB-CORE-MIB
Category: Switching
Description: Defines core system management objects for the 3Com PowerHub chassis, including inventory, power, and slot status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is POWERHUB-CORE-MIB?
POWERHUB-CORE-MIB defines core system management objects for the 3Com PowerHub chassis-based Ethernet switching platform. It exposes chassis inventory, power supply status, and slot/module presence and state information. This is primarily a hardware status MIB: it enables monitoring of power supply health and slot occupancy/state, which are key indicators of physical chassis reliability in a modular switch. It is largely self-contained as a core chassis MIB, though it likely works alongside companion PowerHub MIBs (such as POWERHUB-TCPIP-MIB) for a complete management picture. It is deployed in legacy enterprise/campus network cores built on the 3Com PowerHub modular chassis platform. Network engineers evaluating or troubleshooting this functionality can download the POWERHUB-CORE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in POWERHUB-CORE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- 3Com PowerHub chassis switch
Monitoring Examples
No sample_objects were provided in the source, so specific object or table names cannot be cited; in general an admin would poll chassis slot state and power supply status to detect a failed power module or an empty/faulted slot. Given the description references inventory, power, and slot status, a realistic scenario is checking for a power supply going from normal to failed state, triggering a redundancy alert. This remains a general characterization absent concrete identifiers.
This MIB depends on
Related MIBs
Imported Objects
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| NetworkAddress | |
| OBJECT-TYPE | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| fore | 1.3.6.1.4.1.326 | |||
| systems | 1.3.6.1.4.1.326.2 | |||
| lsd | 1.3.6.1.4.1.326.2.6 | |||
| lsdproducts | 1.3.6.1.4.1.326.2.6.1 | |||
| powerhub4k6k7k | 1.3.6.1.4.1.326.2.6.1.1 | |||
| alchassis | 1.3.6.1.4.1.326.2.6.1.1.1 | |||
| NTF powerFailure | 1.3.6.1.4.1.326.2.6.1.1.1.0.1 | The powerFailure trap indicates that powerFailure occured in the particular powersupply unit. | ||
| NTF boardFailure | 1.3.6.1.4.1.326.2.6.1.1.1.0.2 | The boardFailure trap indicates that intelligent card failure occured in the particular slot. | ||
| alSlotTable | 1.3.6.1.4.1.326.2.6.1.1.1.1 | not-accessible | A table that contains information about each slot in the PowerHub 4k6k7k chassis. | |
| alSlotEntry | 1.3.6.1.4.1.326.2.6.1.1.1.1.1 | not-accessible | Information about a specific slot. | |
| INT alSlotNumber | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.1 | INTEGER | read-only | The slot number for which the following information applies. |
| INT alSlotCardType | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.2 | INTEGER | read-only | The card type for this slot. |
| INT alSlotStatus | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.3 | INTEGER | read-only | The status of the card in this slot. |
| STR alSlotModel | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.4 | DisplayString | read-only | The model number for this card. |
| STR alSlotRevision | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.5 | DisplayString | read-only | The revision number for this card. |
| STR alSlotIssue | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.6 | DisplayString | read-only | The issue number for this slot. |
| STR alSlotDeviation | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.7 | DisplayString | read-only | The deviation for this slot. |
| STR alSlotSerialNumber | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.8 | DisplayString | read-only | The serial number of this card this slot. |
| INT alSlotPower5 | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.9 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at 5 Volts. |
| INT alSlotPower12 | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.10 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at 12 Volts. |
| INT alSlotPower33 | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.11 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at 3.3 Volts. |
| INT alSlotPowerOther | 1.3.6.1.4.1.326.2.6.1.1.1.1.1.12 | INTEGER | read-only | The number of milliamps. of current drawn by this slot at OTHER voltage. |
| alVportTable | 1.3.6.1.4.1.326.2.6.1.1.1.2 | not-accessible | A table that contains information about each virtual port in the PowerHub 4k6k7k chassis. This table differs from the alSlotToVportTable mainly in how this table is indexed. | |
| alVportEntry | 1.3.6.1.4.1.326.2.6.1.1.1.2.1 | not-accessible | Information about a specific virtual port. | |
| INT alVportNumber | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.1 | INTEGER | read-only | The virtual port number for which the following information applies. |
| INT alVportSlotNumber | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.2 | INTEGER | read-only | The slot number which holds the physical port that corresponds to the virtual port of interest. |
| INT alVportPortNumber | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.3 | INTEGER | read-only | The physical port number on the slot that corresponds to this virtual port number, identified by alVportNumber. |
| INT alVportPortType | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.4 | INTEGER | read-only | The port type for this virtual port. |
| INT alVportStatus | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.5 | INTEGER | read-only | The port status for this virtual port. |
| INT alVportControllerType | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.6 | INTEGER | read-only | The controller type for this virtual port. |
| INT alVportDataRateConfig | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.7 | INTEGER | read-write | The data rate requested for this virtual port. |
| INT alVportOperModeConfig | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.8 | INTEGER | read-write | The operating mode requested for this virtual port. |
| INT alVportAutoNegotiateConfig | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.9 | INTEGER | read-write | The auto-negotiation requested for this virtual port. |
| INT alVportDataRateStatus | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.10 | INTEGER | read-only | The actual data rate for this virtual port. |
| INT alVportOperModeStatus | 1.3.6.1.4.1.326.2.6.1.1.1.2.1.11 | INTEGER | read-only | The actual operating mode for this virtual port. |
| alSlotToVportTable | 1.3.6.1.4.1.326.2.6.1.1.1.3 | not-accessible | A table that contains information about each port of each slot in the PowerHub 4k6k7k chassis. This table is established as a way to specify the information about a physical port located on a slot in the PowerHub 4k6k7k chassis. This table a slot and port number scheme. This table differs from uses two indices (the slot number and the port number) to identify a port. | |
| alSlotVportEntry | 1.3.6.1.4.1.326.2.6.1.1.1.3.1 | not-accessible | Information about a specific port in a specific slot. The slot number and the port number in that slot (numbered left to right in ascending order) identifies a specific port. | |
| INT alSlotVportSlotNumber | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.1 | INTEGER | read-only | The slot number which holds the port of interest. |
| INT alSlotVportPortNumber | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.2 | INTEGER | read-only | The physical port number on a slot which represents the port of interest. The physical port is numbered from left to right in a slot. |
| INT alSlotVportNumber | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.3 | INTEGER | read-only | The virtual port number which corresponds to the port that is identified by the slot and port number. This scheme thereby relates each virtual port to a slot and physical port tuplet. |
| INT alSlotVportPortType | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.4 | INTEGER | read-only | The port type for this port. |
| INT alSlotVportStatus | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.5 | INTEGER | read-only | The status for this port. |
| INT alSlotVportControllerType | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.6 | INTEGER | read-only | The controller type for this port. |
| INT alSlotVportDataRateConfig | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.7 | INTEGER | read-write | The data rate requested for this port. The actual data rate may be different from the requested data rate. |
| INT alSlotVportOperModeConfig | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.8 | INTEGER | read-write | The operating mode requested for this port. |
| INT alSlotVportAutoNegotiateConfig | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.9 | INTEGER | read-write | The auto-negotiation requested for this port. |
| INT alSlotVportDataRateStatus | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.10 | INTEGER | read-only | The actual data rate for this port. |
| INT alSlotVportOperModeStatus | 1.3.6.1.4.1.326.2.6.1.1.1.3.1.11 | INTEGER | read-only | The actual operating mode for this port. |
| alPSTable | 1.3.6.1.4.1.326.2.6.1.1.1.4 | not-accessible | A table that contains information about each power supply in the PowerHub 4k6k7k chassis. | |
| alPSEntry | 1.3.6.1.4.1.326.2.6.1.1.1.4.1 | not-accessible | Information about a specific power supply. | |
| INT alPSNumber | 1.3.6.1.4.1.326.2.6.1.1.1.4.1.1 | INTEGER | read-only | The power supply number |
| INT alPSStatus | 1.3.6.1.4.1.326.2.6.1.1.1.4.1.2 | INTEGER | read-only | The status of the power supply identified by the instance of alPSNumber. |
| INT alCpuSlot | 1.3.6.1.4.1.326.2.6.1.1.1.5 | INTEGER | read-only | The slot number in which the packet engine resides |
| INT alSlotChassis | 1.3.6.1.4.1.326.2.6.1.1.1.6 | INTEGER | read-only | The maximum number of slots available in the powerhub. Presently it could either be a 5, 10, or 15 slot chassis. This object is used only for PH7000. |
| powerbits | 1.3.6.1.4.1.326.2.6.1.2 | |||
| asn9000 | 1.3.6.1.4.1.326.2.6.1.3 | |||
| lsdcommon | 1.3.6.1.4.1.326.2.6.2 | |||
| alsystem | 1.3.6.1.4.1.326.2.6.2.1 | |||
| NTF alLoginFailure | 1.3.6.1.4.1.326.2.6.2.1.0.1 | The login failure trap indicates that the login failed due to some error condition during the login process. | ||
| INT alChassisType | 1.3.6.1.4.1.326.2.6.2.1.1 | INTEGER | read-only | The model type of the PowerHub |
| STR alMcpuRtVer | 1.3.6.1.4.1.326.2.6.2.1.2 | DisplayString | read-only | Runtime software version of the motherboard CPU; it is an ASCII string that describes the version as well as the date and time the software was released from the factory. |
| STR alMcpuPromVer | 1.3.6.1.4.1.326.2.6.2.1.3 | DisplayString | read-only | PROM software version of the motherboard CPU; it is an ASCII string that describes the version as well as the date and time the software was released from the factory. |
| STR alFcpuOneRtVer | 1.3.6.1.4.1.326.2.6.2.1.4 | DisplayString | read-only | Runtime software version of F-bus CPU for the first FDDI board. |
| STR alFcpuTwoRtVer | 1.3.6.1.4.1.326.2.6.2.1.5 | DisplayString | read-only | Runtime software version of F-bus CPU for the second FDDI board. |
| STR alFcpuOnePromVer | 1.3.6.1.4.1.326.2.6.2.1.6 | DisplayString | read-only | PROM software version of F-bus CPU for the first FDDI board. |
| STR alFcpuTwoPromVer | 1.3.6.1.4.1.326.2.6.2.1.7 | DisplayString | read-only | PROM software version of F-bus CPU for the second FDDI board. |
| STR alRcpuOneRtVer | 1.3.6.1.4.1.326.2.6.2.1.8 | DisplayString | read-only | Runtime software version of Ring CPU for the first FDDI board. |
| STR alRcpuTwoRtVer | 1.3.6.1.4.1.326.2.6.2.1.9 | DisplayString | read-only | Runtime software version of Ring CPU for the second FDDI board. |
| STR alRcpuOnePromVer | 1.3.6.1.4.1.326.2.6.2.1.10 | DisplayString | read-only | PROM software version of Ring CPU for the first FDDI board. |
| STR alRcpuTwoPromVer | 1.3.6.1.4.1.326.2.6.2.1.11 | DisplayString | read-only | PROM software version of Ring CPU for the second FDDI board. |
| STR alLastLoginFailureTimeDate | 1.3.6.1.4.1.326.2.6.2.1.12 | DisplayString | read-only | Time and date string of the last login session that failed. |
| STR alLastLoginFailureUserId | 1.3.6.1.4.1.326.2.6.2.1.13 | DisplayString | read-only | User id of the last login session that failed. |
| INT alLastLoginFailureReason | 1.3.6.1.4.1.326.2.6.2.1.14 | INTEGER | read-only | Reason code for the last login failure. |
| STR alLastLoginSourceAddress | 1.3.6.1.4.1.326.2.6.2.1.15 | DisplayString | read-only | Source address of the last login session that failed. The value would be either 'console' or ipaddress string of the telnet session. |
| INT alConsoleSyslogLevel | 1.3.6.1.4.1.326.2.6.2.1.17 | INTEGER | read-write | Level which generates a logging messsage for console port commands (telnet, tip, etc.); no messages if set to off(1). |
| INT alSnmpSyslogLevel | 1.3.6.1.4.1.326.2.6.2.1.18 | INTEGER | read-write | Level which generates a logging messsage for snmp induced changes; no messages if set to off(1). |
| INT alIlmiSyslogLevel | 1.3.6.1.4.1.326.2.6.2.1.19 | INTEGER | read-write | Level which generates a logging messsage for ilmi configuration changes; no messages if set to off(1). |
| INT alSyslogHostType | 1.3.6.1.4.1.326.2.6.2.1.20 | INTEGER | read-write | Host which receives syslog messages: notSet(1) if no host is set or becomes unset; local(2) if messages go to console; ip(3) if messages go to a remote host |
| STR alSyslogHostIp | 1.3.6.1.4.1.326.2.6.2.1.21 | DisplayString | read-write | IP address of remote host which receives syslog messages; must be set if alSyslogHost is set to ip. |
| INT alSyslogHostIpFacility | 1.3.6.1.4.1.326.2.6.2.1.22 | INTEGER | read-write | Syslog facility to be assigned to all syslog messages. Default is daemon(1). |
| albridge | 1.3.6.1.4.1.326.2.6.2.2 | |||
| alBridgeTable | 1.3.6.1.4.1.326.2.6.2.2.1 | not-accessible | A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. | |
| alBridgeEntry | 1.3.6.1.4.1.326.2.6.2.2.1.1 | not-accessible | Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information. | |
| MAC alBridgeEntryAddress | 1.3.6.1.4.1.326.2.6.2.2.1.1.1 | MacAddress | read-only | The MAC address for which the bridge has forwarding and/or filtering information. |
| INT alBridgeEntryPort | 1.3.6.1.4.1.326.2.6.2.2.1.1.2 | INTEGER | read-only | The port number of the port on which a frame having a source address equal to the value of the corresponding instance of alBridgeEntryAddress has been seen. |
| INT alBridgeEntryLink | 1.3.6.1.4.1.326.2.6.2.2.1.1.3 | INTEGER | read-only | The link number on the port on which a frame having as ource address equal to the value of the corresponding instance of alBridgeEntryAddress has been seen. Only applies to the UTP port type. |
| INT alBridgeEntryRule | 1.3.6.1.4.1.326.2.6.2.2.1.1.4 | INTEGER | read-only | The rule number that is applied to packets that are forwarded to or from this address. |
| INT alBridgeEntryFlags | 1.3.6.1.4.1.326.2.6.2.2.1.1.5 | INTEGER | read-only | The status of this entry. |
| INT alBridgeTblClear | 1.3.6.1.4.1.326.2.6.2.2.2 | INTEGER | read-write | When set, clears the Bridge table. |
| INT alBrFlushCache | 1.3.6.1.4.1.326.2.6.2.2.3 | INTEGER | read-write | When set, flushes the cache. |
| alPortStatsTable | 1.3.6.1.4.1.326.2.6.2.2.4 | not-accessible | Per port statistics | |
| portStatsEntry | 1.3.6.1.4.1.326.2.6.2.2.4.1 | not-accessible | Per port statistics entries. | |
| INT portStatsPort | 1.3.6.1.4.1.326.2.6.2.2.4.1.1 | INTEGER | read-only | Segment for which the statistics collected. |
| CTR portStatsPktsIn | 1.3.6.1.4.1.326.2.6.2.2.4.1.2 | Counter | read-only | Good packets received on the segment. Packets are listed regardless of packet type, or whether the packet is forwarded to another segment. Error packets are not listed. |
| CTR portStatsPktsOut | 1.3.6.1.4.1.326.2.6.2.2.4.1.3 | Counter | read-only | Packets transmitted on the segment. This statistic is incremented when a packet is scheduled for transmission, not when it is actually transmitted. |
| CTR portStatsOctetsIn | 1.3.6.1.4.1.326.2.6.2.2.4.1.4 | Counter | read-only | Good octets received on the segment. This statistic includes 8 octets per packet to account for the preamble. |
| CTR portStatsOctetsOut | 1.3.6.1.4.1.326.2.6.2.2.4.1.5 | Counter | read-only | Octets transmitted from the segment. This statistic is incremented when a packet is scheduled for transmission, not when it is actually transmitted. This statistic includes 8 octets per packet to account for the preamble. |
| CTR portStatsMulticastPktsIn | 1.3.6.1.4.1.326.2.6.2.2.4.1.6 | Counter | read-only | Broadcast multicast packets received on the segment. This statistic is incremented for each good broadcast or multicast packet received on the segment. |
| CTR portStatsMulticastPktsOut | 1.3.6.1.4.1.326.2.6.2.2.4.1.7 | Counter | read-only | Broadcast multicast packets transmitted from the segment. This statistic is incremented once for each broadcast or multicast packet scheduled for transmission on the segment. |
| CTR portStatsTableMisses | 1.3.6.1.4.1.326.2.6.2.2.4.1.8 | Counter | read-only | Packets received that have unknown destination addresses. When address learning is enabled, this statistic is usually incremented only for the first packet transmitted to a workstation or other device connected to the segment. After a reply is received, the device's source address is added to the bridging table. |
| CTR portStatsRcvBuffErrs | 1.3.6.1.4.1.326.2.6.2.2.4.1.9 | Counter | read-only | Incremented each time the hub detects an incoming packet but does not have a buffer in which to store the packet. |
| CTR portStatsXmitBuffErrs | 1.3.6.1.4.1.326.2.6.2.2.4.1.10 | Counter | read-only | Incremented each time the hub attempts to forward a packet to a busy destination segment whose output buffers all are full. |
| CTR portStatsTotalCollisions | 1.3.6.1.4.1.326.2.6.2.2.4.1.11 | Counter | read-only | The total number of collisions detected on the segment while attempting to transmit and receive packets. For FDDI segments, this statistic is always 0. |
| CTR portStatsRcvCollisions | 1.3.6.1.4.1.326.2.6.2.2.4.1.12 | Counter | read-only | The number of collisions detected on the segment while listening for incoming packets. This statistic is only available for UTP segments. For segments on other module types, this statistic is always 0. |
| CTR portStatsXmitCollisions | 1.3.6.1.4.1.326.2.6.2.2.4.1.13 | Counter | read-only | The number of collisions detected on the segment while attempting to transmit packets. For FDDI segments, this statistic is always 0. |
| CTR portStatsXmitQLen | 1.3.6.1.4.1.326.2.6.2.2.4.1.14 | Counter | read-only | The number of outgoing packets in the transmit queue. These packets have been scheduled for transmission, but have not been transmitted yet. |
| CTR portStatsPeakUtilization | 1.3.6.1.4.1.326.2.6.2.2.4.1.15 | Counter | read-only | The segment's maximum utilization during a one-second interval since the statistics last were cleared. For Ethernet segments, the current utilization is calculated as follows: Once per second, the current one- second utilization is computed as (total # octets) x (8 bits/octets) / 10 Mb/s. The peak utilization is then set to the maximum of the current one-second utilization and the previous peak utilization. NOTE: Total # octets is all octets transmitted and received on the segment during the previous second, including 8 octets of preamble per packet. The Ethernet rate is 10Mb. |
| CTR portStatsCurrUtilization | 1.3.6.1.4.1.326.2.6.2.2.4.1.16 | Counter | read-only | For Ethernet segments, the current utilization is calculated as follows: Once per second, the current one-second utilization is computed as (total # octets) x (8 bits/octets) / 10 Mb/s. NOTE: Total # octets is all octets transmitted and received on the segment during the previous second, including 8 octets of preamble per packet. The Ethernet rate is 10Mb. |
| CTR portStatsLossOfCarrier | 1.3.6.1.4.1.326.2.6.2.2.4.1.17 | Counter | read-only | Indicates that an AUI segment has no cable attached, or the cable or transceiver is faulty. |
| CTR portStatsExcessRetries | 1.3.6.1.4.1.326.2.6.2.2.4.1.18 | Counter | read-only | Incremented whenever all of 15 attempts to transmit a single packet cause collisions. This can happen in very busy networks, or when no cable is attached to an enabled BNC port. |
| INT alBridgeStatsClear | 1.3.6.1.4.1.326.2.6.2.2.5 | INTEGER | read-write | When set, clears the statistics for the bridge. When not set, value 0 is returned. |
| INT alBridgePPControl | 1.3.6.1.4.1.326.2.6.2.2.6 | INTEGER | read-write | When set to 3 , disables the port to port collection of the stats; when set to 1, enables the port to port stats collection; when set to 2, clears the port to port stats. |
| alPortToPortTable | 1.3.6.1.4.1.326.2.6.2.2.7 | not-accessible | Statistics for port to port traffic. | |
| portToPortEntry | 1.3.6.1.4.1.326.2.6.2.2.7.1 | not-accessible | Statistics for port to port traffic | |
| INT alPPSourcePort | 1.3.6.1.4.1.326.2.6.2.2.7.1.1 | INTEGER | read-only | Source port number |
| INT alPPDestinationPort | 1.3.6.1.4.1.326.2.6.2.2.7.1.2 | INTEGER | read-only | Destination port number |
| INT portToPortPackets | 1.3.6.1.4.1.326.2.6.2.2.7.1.3 | INTEGER | read-only | Port to port packets. |
| INT portToPortOctets | 1.3.6.1.4.1.326.2.6.2.2.7.1.4 | INTEGER | read-only | Port to port octets. |
| alPortConfigTable | 1.3.6.1.4.1.326.2.6.2.2.8 | not-accessible | Per port configuration for configuring Source and Destination Rules etc. | |
| portConfigEntry | 1.3.6.1.4.1.326.2.6.2.2.8.1 | not-accessible | Per port configuration. | |
| INT portConfigPort | 1.3.6.1.4.1.326.2.6.2.2.8.1.1 | INTEGER | read-only | The port number for this table entry |
| INT portConfigSrcRule | 1.3.6.1.4.1.326.2.6.2.2.8.1.2 | INTEGER | read-write | Source Rule for the port number identified by the instance of portConfigPort |
| INT portConfigDstRule | 1.3.6.1.4.1.326.2.6.2.2.8.1.3 | INTEGER | read-write | Destination Rule for the port number identified by the instance of portConfigPort |
| INT portConfigBlockLearnedEntries | 1.3.6.1.4.1.326.2.6.2.2.8.1.4 | INTEGER | read-write | When set to True (1), the port identified by the instance of portConfigPort will block the learned entries; if set to False (2) the port will not block the learned entries |
| INT alBridgeIpBridging | 1.3.6.1.4.1.326.2.6.2.2.9 | INTEGER | read-write | When set to enable(1), enables the IP bridging and if set to disable(2), disables the IP bridging. |
| alBrTemplateTable | 1.3.6.1.4.1.326.2.6.2.2.10 | not-accessible | Per template information | |
| brTemplateEntry | 1.3.6.1.4.1.326.2.6.2.2.10.1 | not-accessible | Template entry. | |
| INT brTemplateNumber | 1.3.6.1.4.1.326.2.6.2.2.10.1.1 | INTEGER | read-only | The number of the template with which it is identified. |
| INT brTemplateOffset | 1.3.6.1.4.1.326.2.6.2.2.10.1.2 | INTEGER | read-write | A displacement, in octets, from the beginning of the packet. This must be a multiple of 4 in the range from 0 to 124 decimal. A value of -1 will delete the entry |
| STR brTemplateMask | 1.3.6.1.4.1.326.2.6.2.2.10.1.3 | DisplayString | read-write | A 4-byte (32-bit) number, normally specified as eight hexadecimal digits (00000000 - ffffffff) Description: The bytes in the mask are numbered from 0 to 3, starting with the high-order byte (big-endian format). Each byte of the mask is ANDed with the octet in the packet at displacement 'offset + i' to form a 4-byte 'masked value'. |
| STR brTemplateComparator | 1.3.6.1.4.1.326.2.6.2.2.10.1.4 | DisplayString | read-write | A 4-byte number, usually specified as eight hexadecimal digits (00000000 - ffffffff) Description: If the masked value defined above equals the comparator, then the template returns a value of 'true'; otherwise, it returns a value of 'false'. |
| INT brTemplateOption | 1.3.6.1.4.1.326.2.6.2.2.10.1.5 | INTEGER | read-write | Setting this value to 0 assume all 32 bits mask and comparator specified; value 1 assume half-word (2 bytes) qunatity; and value 2 assume single-byte quantity. |
| alBrRuleTable | 1.3.6.1.4.1.326.2.6.2.2.11 | not-accessible | Per rule information | |
| brRuleEntry | 1.3.6.1.4.1.326.2.6.2.2.11.1 | not-accessible | Rule entry. | |
| INT brRuleNumber | 1.3.6.1.4.1.326.2.6.2.2.11.1.1 | INTEGER | read-only | A rule number in the range 101-162. You can define up to 62 rules. |
| STR brRuleStatement | 1.3.6.1.4.1.326.2.6.2.2.11.1.2 | DisplayString | read-write | Specifies the templates and the logical operators that make up the rule. Rule statements consist of rule numbers joined by the following logical operators: Operator Means... & AND | OR ~ NOT Rule statements are interpreted from left to right. Use parentheses to group expressions. You can use up to eight sets of parentheses to group template numbers and logical operators. The total maximum number of characters, including blanks, is 64. |
| alBrRuleToNodeTable | 1.3.6.1.4.1.326.2.6.2.2.12 | not-accessible | Rules to specific node. | |
| alBrRuleToNodeEntry | 1.3.6.1.4.1.326.2.6.2.2.12.1 | not-accessible | Rule node entry. | |
| INT brRuleToNodePort | 1.3.6.1.4.1.326.2.6.2.2.12.1.1 | INTEGER | read-write | The number of the port for which this rule applies |
| PHY brRuleToNodeMacAddr | 1.3.6.1.4.1.326.2.6.2.2.12.1.2 | PhysAddress | read-write | The source MAC address |
| INT brRuleToNodeRule | 1.3.6.1.4.1.326.2.6.2.2.12.1.3 | INTEGER | read-write | The rule number that applies to this entry. |
| alBrGroupTable | 1.3.6.1.4.1.326.2.6.2.2.13 | not-accessible | Bridge group table. | |
| alBrGroupEntry | 1.3.6.1.4.1.326.2.6.2.2.13.1 | not-accessible | Bridge group entry. | |
| INT brGroupNumber | 1.3.6.1.4.1.326.2.6.2.2.13.1.1 | INTEGER | read-only | The group number by which the group is identified with. |
| STR brGroupPortsMask | 1.3.6.1.4.1.326.2.6.2.2.13.1.2 | DisplayString | read-write | The ports associated with the group number identified by the instance of brGroupNumber. The mask is ascii segments separated by commas. A value of -1 would invalidate the appropriate group. |
| STR brGroupName | 1.3.6.1.4.1.326.2.6.2.2.13.1.3 | DisplayString | read-write | The name of the group for which this entry applies |
| INT alBridgeSTPControl | 1.3.6.1.4.1.326.2.6.2.2.14 | INTEGER | read-write | When set to 2 , disables the spanning tree. set to 1, enables the spanning tree. |
| alPortStateTable | 1.3.6.1.4.1.326.2.6.2.2.15 | not-accessible | Per port state information about spanning tree, dignostics and management. | |
| portStateEntry | 1.3.6.1.4.1.326.2.6.2.2.15.1 | not-accessible | Port state entry. | |
| INT portStatePort | 1.3.6.1.4.1.326.2.6.2.2.15.1.1 | INTEGER | read-only | The port number for this table entry |
| INT portStateDiag | 1.3.6.1.4.1.326.2.6.2.2.15.1.2 | INTEGER | read-only | The diagnostics state of the port |
| INT portStateMgmt | 1.3.6.1.4.1.326.2.6.2.2.15.1.3 | INTEGER | read-only | The management state of the port |
| INT portStateStp | 1.3.6.1.4.1.326.2.6.2.2.15.1.4 | INTEGER | read-only | The spanning tree state of the port. |
| STR portStatePortName | 1.3.6.1.4.1.326.2.6.2.2.15.1.5 | DisplayString | read-only | The name of this port |
| almgmt | 1.3.6.1.4.1.326.2.6.2.3 | |||
| alAutoPortStateTable | 1.3.6.1.4.1.326.2.6.2.3.1 | not-accessible | auto port stat table | |
| autoportStateEntry | 1.3.6.1.4.1.326.2.6.2.3.1.1 | not-accessible | auto port stat entry. | |
| INT autoPortStatePort | 1.3.6.1.4.1.326.2.6.2.3.1.1.1 | INTEGER | read-only | The port number for this table entry |
| INT autoPortState | 1.3.6.1.4.1.326.2.6.2.3.1.1.2 | INTEGER | read-write | Whether the auto port state detection is turned on or not. |
| INT autoPortStateThreshold | 1.3.6.1.4.1.326.2.6.2.3.1.1.3 | INTEGER | read-write | Corresponding to the threshold parameter of the autoportstate command. |
| INT alLinkStatsCollect | 1.3.6.1.4.1.326.2.6.2.3.2 | INTEGER | read-write | When set to enable(1), per link stats collection is enabled; when set to disable(0), the per link stats are not collected. |
| INT alLinkStatsClear | 1.3.6.1.4.1.326.2.6.2.3.3 | INTEGER | read-write | When set, clears the link stats; otherwise value 0 is returned. |
| alLinkStatsTable | 1.3.6.1.4.1.326.2.6.2.3.4 | not-accessible | Per link stats table | |
| linkStatsEntry | 1.3.6.1.4.1.326.2.6.2.3.4.1 | read-write | link stats entry. | |
| INT linkStatsPort | 1.3.6.1.4.1.326.2.6.2.3.4.1.1 | INTEGER | read-only | Port Number |
| CTR linkStatsLink | 1.3.6.1.4.1.326.2.6.2.3.4.1.2 | Counter | read-only | Link Number |
| CTR linkStatsPktsIn | 1.3.6.1.4.1.326.2.6.2.3.4.1.3 | Counter | read-only | Pkts In - corresponds to pi |
| CTR linkStatsOctetsIn | 1.3.6.1.4.1.326.2.6.2.3.4.1.4 | Counter | read-only | Octets In - corresponds to oi |
| CTR linkStatsBMCastPktsIn | 1.3.6.1.4.1.326.2.6.2.3.4.1.5 | Counter | read-only | Bmcast Pks In - corresponds to bpi |
| CTR linkStatsGiantPkts | 1.3.6.1.4.1.326.2.6.2.3.4.1.6 | Counter | read-only | Giant Pkts - corresponds to gp |
| CTR linkStatsFrameErrs | 1.3.6.1.4.1.326.2.6.2.3.4.1.7 | Counter | read-only | Frame Errors - corresponds to fa |
| CTR linkStatsFCSErrs | 1.3.6.1.4.1.326.2.6.2.3.4.1.8 | Counter | read-only | FCS Errors corresponds to fcs |
| CTR linkStatsCodingErrors | 1.3.6.1.4.1.326.2.6.2.3.4.1.9 | Counter | read-only | This Counter is incremented when the receiver (RX) port detects an invalid symbol in the incoming code sent by the TX port using symbol mode. |
| CTR linkStatsDataRateMismatch | 1.3.6.1.4.1.326.2.6.2.3.4.1.10 | Counter | read-only | This counter is incremented by one for each frame received on this port that meets all of the following conditions: 1) The Collision Event signal is not asserted 2) The Activity duration is greater than ValidPacketMinTime 3) The frequency (data rate) is detectably mismatched from the local transmit frequency |
| CTR linkStatsJabbers | 1.3.6.1.4.1.326.2.6.2.3.4.1.11 | Counter | read-only | This Counter is incremented for each CarrierEvent on this port whose ActivityDuration is greater than the MAU Jabber Lockup Protection timer |
| CTR linkStatsShortEvents | 1.3.6.1.4.1.326.2.6.2.3.4.1.12 | Counter | read-only | This counter is incremented for each CarrierEvent on this port with ActivityDuration less than ShortEventMaxTime. |
| CTR linkStatsRunts | 1.3.6.1.4.1.326.2.6.2.3.4.1.13 | Counter | read-only | An event whose length is greater than 74 bit times but less than 82 bit times shall increment either the shortEvents counter or the runts counter but not both |
| CTR linkStatsPortCollision | 1.3.6.1.4.1.326.2.6.2.3.4.1.14 | Counter | read-only | This counter is incremented for any CarrierEvent signal on any port for which the CollisionEvent signal on this port is also asserted. |
| CTR linkStatsLateCollision | 1.3.6.1.4.1.326.2.6.2.3.4.1.15 | Counter | read-only | This counter is incremented for each CarrierEvent on this port in which the CollIn(X) variable transitions to the value SQE while the ActivityDuration is greater than the LAteEventThreshold. |
| CTR linkStatsAutoPartition | 1.3.6.1.4.1.326.2.6.2.3.4.1.16 | Counter | read-only | This counter is incremented each time the repeater has automatically partitioned this port |
| CTR linkStatsIsolates | 1.3.6.1.4.1.326.2.6.2.3.4.1.17 | Counter | read-only | This counter is incremented whenever the port detects two consecutive carrier integrity false carriers. |
| CTR linkStatsSaFieldChanges | 1.3.6.1.4.1.326.2.6.2.3.4.1.18 | Counter | read-only | This counter is incremented for each time that the rptrAddrTrackLastSourceAddress attribute for this port has changed. |
| MAC linkStatsLastSa | 1.3.6.1.4.1.326.2.6.2.3.4.1.19 | MacAddress | read-only | This object is the SourceAddress of the last readable frame received by this port. |
| alLinkControlTable | 1.3.6.1.4.1.326.2.6.2.3.5 | not-accessible | Per link stats table | |
| linkControlEntry | 1.3.6.1.4.1.326.2.6.2.3.5.1 | read-write | link control entry. | |
| INT linkControlPort | 1.3.6.1.4.1.326.2.6.2.3.5.1.1 | INTEGER | read-only | Port number for this entry. |
| INT linkControlLink | 1.3.6.1.4.1.326.2.6.2.3.5.1.2 | INTEGER | read-only | Link number for this entry. |
| INT linkControlEnlState | 1.3.6.1.4.1.326.2.6.2.3.5.1.3 | INTEGER | read-write | Setting the value of this object to Enable (1) will enable the link and setting to Disable(2) will disable the link. |
| INT linkControlLinkTest | 1.3.6.1.4.1.326.2.6.2.3.5.1.4 | INTEGER | read-only | Link test status for the link; corresponds to lt option of the lkd command. |
| INT linkControlPartition | 1.3.6.1.4.1.326.2.6.2.3.5.1.5 | INTEGER | read-only | Partitioning state of the link |
| INT linkControlPolarity | 1.3.6.1.4.1.326.2.6.2.3.5.1.6 | INTEGER | read-only | Polarity of the link |
| alPortLinkTable | 1.3.6.1.4.1.326.2.6.2.3.6 | not-accessible | Per port link type | |
| portLinkEntry | 1.3.6.1.4.1.326.2.6.2.3.6.1 | not-accessible | port link entry. | |
| INT portLinkPort | 1.3.6.1.4.1.326.2.6.2.3.6.1.1 | INTEGER | read-only | The port number for which the port type is to be set |
| INT portLinkType | 1.3.6.1.4.1.326.2.6.2.3.6.1.2 | INTEGER | read-write | The type of port |
| alFiberStatsTable | 1.3.6.1.4.1.326.2.6.2.3.7 | not-accessible | Per port fiber stats and Fiber Security | |
| fiberStatsEntry | 1.3.6.1.4.1.326.2.6.2.3.7.1 | not-accessible | fiber stat entry. | |
| INT fiberStatsPort | 1.3.6.1.4.1.326.2.6.2.3.7.1.1 | INTEGER | read-only | The fiber port for which the stats are requested or the Fiber violation is set |
| INT fiberAuiStatus | 1.3.6.1.4.1.326.2.6.2.3.7.1.2 | INTEGER | read-only | The fiber aui status for the port that is specified by the instance of fiberStatsPort |
| INT fiberSecurityViolation | 1.3.6.1.4.1.326.2.6.2.3.7.1.3 | INTEGER | read-write | The fiber port for which the stats are requested or the Fiber violation is set |
| INT alPortMonitorClose | 1.3.6.1.4.1.326.2.6.2.3.8 | INTEGER | read-write | Setting the value to close(1), will turn the port monitoring off. |
| alPortMonitorTable | 1.3.6.1.4.1.326.2.6.2.3.9 | not-accessible | port monitor table. | |
| portMonitorEntry | 1.3.6.1.4.1.326.2.6.2.3.9.1 | not-accessible | port monitor entry. | |
| INT portMonSrcPort | 1.3.6.1.4.1.326.2.6.2.3.9.1.1 | INTEGER | read-only | The traffic to/from this port will be monitored on the portMonDstPort |
| INT portMonDstPort | 1.3.6.1.4.1.326.2.6.2.3.9.1.2 | INTEGER | read-only | The traffic to/from portMonSrcPort will be monitored on this port |
| INT portMonTrafficType | 1.3.6.1.4.1.326.2.6.2.3.9.1.3 | INTEGER | read-write | Setting this value to 1, will let the port monitor monitor forwarded traffic; setting to 8 means the forwarded traffic will not be monitored. |
| INT alReboot | 1.3.6.1.4.1.326.2.6.2.3.10 | INTEGER | write-only | Setting the value to Reboot(1), will reboot the PowerHub. |
| alPortMonitorViewTable | 1.3.6.1.4.1.326.2.6.2.3.11 | not-accessible | port monitor view table. | |
| portMonitorViewEntry | 1.3.6.1.4.1.326.2.6.2.3.11.1 | not-accessible | port monitor view entry. | |
| INT portMonViewSrcPort | 1.3.6.1.4.1.326.2.6.2.3.11.1.1 | INTEGER | read-only | The traffic from this port to the port designated by portMonViewDstPort will be monitored on portMonViewMonitorPort. |
| INT portMonViewDstPort | 1.3.6.1.4.1.326.2.6.2.3.11.1.2 | INTEGER | read-only | The traffic to this port from the port designated by portMonViewSrcPort will be monitored on portMonViewMonitorPort. |
| STR portMonViewMonitorPort | 1.3.6.1.4.1.326.2.6.2.3.11.1.3 | DisplayString | read-write | The traffic to portMonViewDstPort from the port designated by portMonViewSrcPort will be monitored on portMonViewMonitorPort. The mask is ascii, segments separated by commas. |
| INT alCfgLocalMediaScope | 1.3.6.1.4.1.326.2.6.2.3.12 | INTEGER | read-only | This object display the types of local media currently available on the PH for storing files. The PH4000 and PH6000 do not support floppy whereas the PH3000 and PH5000 do not support flash. The flash is optional on PH6000 & PH7000. All models do support tftpHost save options. Depending on the value of this object, the user can specify the appropriate filename and the media type in other objects for doing the save operation. |
| INT alCfgMediaName | 1.3.6.1.4.1.326.2.6.2.3.13 | INTEGER | read-write | This object specify the medium name to which the the powerhub will save the configurations. The value 'none' is returned when user have not set the valid save medium. Save operation cannot be performed when value is set to 'none'. |
| IP alCfgTftpHostAddr | 1.3.6.1.4.1.326.2.6.2.3.14 | IpAddress | read-write | This object specify the IP address of the tftp host system to which the configs get saved when the object alCfgMediaName is set with value tftpHost(3). |
| STR alCfgFileName | 1.3.6.1.4.1.326.2.6.2.3.15 | DisplayString | read-write | This object specify the configuration filename to which the PH will save the configuration. Depending on the medium (floppy, flash, or tftpHost) in which the saving will be done, the filename have to be set correctly. For example, the filename for floppy and flash medium cannot exceed 8 characters. The filnames can be appended with the optional dot character followed by 3 character extension. The filenames for tftp host should have been pre-created on the host and it should be writable by the PH. All tftp file access restrictions apply. |
| INT alCfgSaveOp | 1.3.6.1.4.1.326.2.6.2.3.16 | INTEGER | read-write | Save config operation can be performed only when this object is set to value '1'. This field returns a dummy value 100 for get operations. |
RFC description
Manages Fore Systems PowerHub 4k/6k/7k telecommunications chassis and ATM switch components. Provides monitoring of slots, system, bridge, and management functions.
Start monitoring 3Com PowerHub chassis switch (core chassis/power supply/slot status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.